Chris Packham <[email protected]> writes:
> Both the CN9130-CRB and CN9130-DB use the SPI1 interface but had the
> pinctrl node labelled as "cp0_spi0_pins". Use the label "cp0_spi1_pins"
> and update the node name to "cp0-spi-pins-1" to avoid confusion with the
> pinctrl options for SPI0.
>
> Fixes: 4c43a41e5b8c ("arm64: dts: cn913x: add device trees for topology B boards")
> Fixes: 5c0ee54723f3 ("arm64: dts: add support for Marvell cn9130-crb platform")
> Signed-off-by: Chris Packham <[email protected]>
> ---
>
> Notes:
> We noticed this while tracking down a U-Boot bug on one of our
> platforms. This mislabeling had been copied and we ended up using the
> label when configuring SPI0 which had the nasty side effect of
> reconfiguring the NAND/DEV pins into SPI1 mode when SPI0 was probed.
>
> It probably went unnoticed because none of the CN9130 platforms
> supported in upstream U-Boot use NAND.
>
Applied on mvebu/dt64
Thanks,
Gregory
> arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 4 ++--
> arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 4 ++--
> 2 files changed, 4 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
> index 32cfb3e2efc3..47d45ff3d6f5 100644
> --- a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
> +++ b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
> @@ -120,7 +120,7 @@ cp0_sdhci_pins: cp0-sdhi-pins-0 {
> "mpp59", "mpp60", "mpp61";
> marvell,function = "sdio";
> };
> - cp0_spi0_pins: cp0-spi-pins-0 {
> + cp0_spi1_pins: cp0-spi-pins-1 {
> marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
> marvell,function = "spi1";
> };
> @@ -170,7 +170,7 @@ &cp0_sdhci0 {
>
> &cp0_spi1 {
> pinctrl-names = "default";
> - pinctrl-0 = <&cp0_spi0_pins>;
> + pinctrl-0 = <&cp0_spi1_pins>;
> reg = <0x700680 0x50>, /* control */
> <0x2000000 0x1000000>; /* CS0 */
> status = "okay";
> diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi
> index c7de1ea0d470..6eb6a175de38 100644
> --- a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi
> +++ b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi
> @@ -307,7 +307,7 @@ &cp0_sdhci0 {
> &cp0_spi1 {
> status = "disabled";
> pinctrl-names = "default";
> - pinctrl-0 = <&cp0_spi0_pins>;
> + pinctrl-0 = <&cp0_spi1_pins>;
> reg = <0x700680 0x50>;
>
> flash@0 {
> @@ -371,7 +371,7 @@ cp0_sdhci_pins: cp0-sdhi-pins-0 {
> "mpp59", "mpp60", "mpp61";
> marvell,function = "sdio";
> };
> - cp0_spi0_pins: cp0-spi-pins-0 {
> + cp0_spi1_pins: cp0-spi-pins-1 {
> marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
> marvell,function = "spi1";
> };
> --
> 2.41.0
>
--
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com