2020-01-08 17:55:57

by Lad, Prabhakar

[permalink] [raw]
Subject: [v3 0/6] Add support for PCIe controller to work in endpoint mode on R-Car SoCs

This patch series adds support for PCIe controller on rcar to work in
endpoint mode, this also extends the epf framework to handle base region
for mapping PCI address locally..

Note:
The cadence/rockchip/designware endpoint drivers are build tested only.

Changes for v3:
1] Fixed review comments from Bjorn and Kishon.
3] Converted to DT schema

Changes for v2:
1] Fixed review comments from Biju for dt-bindings to include an example
for a tested platform.
2] Fixed review comments from Kishon to extend the features of outbound
regions in epf framework.
3] Added support to parse outbound-ranges in OF.

lspci output on host:
=====================

01:00.0 Unassigned class [ff00]: Renesas Technology Corp. Device 002d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 152
Region 0: Memory at fe200200 (64-bit, non-prefetchable) [size=128]
Region 2: Memory at fe200000 (64-bit, non-prefetchable) [size=256]
Region 4: Memory at fe200100 (64-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
Address: 00000004fa36d000 Data: 0001
Masking: fffffffe Pending: 00000000
Capabilities: [70] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s, Exit Latency L0s unlimited
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: pci-endpoint-test

BAR Test
========
root@g2e:~# pcitest -b 0
BAR0: OKAY
root@g2e:~# pcitest -b 1
BAR1: NOT OKAY
root@g2e:~# pcitest -b 2
BAR2: OKAY
root@g2e:~# pcitest -b 3
BAR3: NOT OKAY
root@g2e:~# pcitest -b 4
BAR4: OKAY
root@g2e:~# pcitest -b 5
BAR5: NOT OKAY

Note: BAR test for 1/3/5 fail because they are configured to be 64bits

Interrupt Test
==============
root@g2e:~# pcitest -i 0
SET IRQ TYPE TO LEGACY: OKAY
root@g2e:~# pcitest -l
LEGACY IRQ: OKAY

Read Test
=========
root@g2e:~# pcitest -r -s 1
READ ( 1 bytes): OKAY
root@g2e:~# pcitest -r -s 1024
READ ( 1024 bytes): OKAY
root@g2e:~# pcitest -r -s 1025
READ ( 1025 bytes): OKAY
root@g2e:~# pcitest -r -s 1024000
READ (1024000 bytes): OKAY
root@g2e:~# pcitest -r -s 1024001
READ (1024001 bytes): OKAY

Write Test
==========
root@g2e:~# pcitest -w -s 1
WRITE ( 1 bytes): OKAY
root@g2e:~# pcitest -w -s 1024
WRITE ( 1024 bytes): OKAY
root@g2e:~# pcitest -w -s 1025
WRITE ( 1025 bytes): OKAY
root@g2e:~# pcitest -w -s 1024000
WRITE (1024000 bytes): OKAY
root@g2e:~# pcitest -w -s 1024001
WRITE (1024001 bytes): OKAY

Copy Test
=========
root@g2e:~# pcitest -c -s 1
COPY ( 1 bytes): OKAY
root@g2e:~# pcitest -c -s 1024
COPY ( 1024 bytes): OKAY
root@g2e:~# pcitest -c -s 1025
COPY ( 1025 bytes): OKAY
root@g2e:~# pcitest -c -s 1024000
COPY (1024000 bytes): OKAY
root@g2e:~# pcitest -c -s 1024001
COPY (1024001 bytes): OKAY


Lad Prabhakar (6):
PCI: rcar: Preparation for adding endpoint support
PCI: rcar: Fix calculating mask for PCIEPAMR register
PCI: endpoint: Add support to handle multiple base for mapping
outbound memory
dt-bindings: PCI: rcar: Add bindings for R-Car PCIe endpoint
controller
PCI: rcar: Add support for rcar PCIe controller in endpoint mode
misc: pci_endpoint_test: Add Device ID for RZ/G2E PCIe controller

.../devicetree/bindings/pci/rcar-pci-ep.yaml | 76 +
arch/arm64/configs/defconfig | 2 +-
drivers/misc/pci_endpoint_test.c | 3 +
drivers/pci/controller/Kconfig | 11 +-
drivers/pci/controller/Makefile | 3 +-
.../pci/controller/cadence/pcie-cadence-ep.c | 12 +-
.../pci/controller/dwc/pcie-designware-ep.c | 31 +-
drivers/pci/controller/pcie-rcar-ep.c | 497 +++++++
drivers/pci/controller/pcie-rcar-host.c | 1044 ++++++++++++++
drivers/pci/controller/pcie-rcar.c | 1232 +----------------
drivers/pci/controller/pcie-rcar.h | 132 ++
drivers/pci/controller/pcie-rockchip-ep.c | 14 +-
drivers/pci/endpoint/functions/pci-epf-test.c | 29 +-
drivers/pci/endpoint/pci-epc-core.c | 7 +-
drivers/pci/endpoint/pci-epc-mem.c | 199 ++-
include/linux/pci-epc.h | 46 +-
16 files changed, 2064 insertions(+), 1274 deletions(-)
create mode 100644 Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
create mode 100644 drivers/pci/controller/pcie-rcar-ep.c
create mode 100644 drivers/pci/controller/pcie-rcar-host.c
create mode 100644 drivers/pci/controller/pcie-rcar.h

--
2.20.1


2020-01-08 17:56:18

by Lad, Prabhakar

[permalink] [raw]
Subject: [v3 4/6] dt-bindings: PCI: rcar: Add bindings for R-Car PCIe endpoint controller

This patch adds the bindings for the R-Car PCIe endpoint driver.

Signed-off-by: Lad Prabhakar <[email protected]>
---
.../devicetree/bindings/pci/rcar-pci-ep.yaml | 76 +++++++++++++++++++
1 file changed, 76 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml

diff --git a/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml b/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
new file mode 100644
index 000000000000..99c2a1174463
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
@@ -0,0 +1,76 @@
+# SPDX-License-Identifier: GPL-2.0
+# Copyright (C) 2020 Renesas Electronics Europe GmbH - https://www.renesas.com/eu/en/
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/rcar-pcie-ep.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas R-Car PCIe Endpoint
+
+maintainers:
+ - Lad Prabhakar <[email protected]>
+
+properties:
+ compatible:
+ items:
+ - const: renesas,r8a774c0-pcie-ep
+ - const: renesas,rcar-gen3-pcie-ep
+
+ reg:
+ maxItems: 5
+
+ reg-names:
+ items:
+ - const: apb-base
+ - const: memory0
+ - const: memory1
+ - const: memory2
+ - const: memory3
+
+ power-domains:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ items:
+ - const: pcie
+
+ max-functions:
+ minimum: 1
+ maximum: 6
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - resets
+ - power-domains
+ - clocks
+ - clock-names
+ - max-functions
+
+examples:
+ - |
+ #include <dt-bindings/clock/r8a774c0-cpg-mssr.h>
+ #include <dt-bindings/power/r8a774c0-sysc.h>
+
+ pcie0_ep: pcie-ep@fe000000 {
+ compatible = "renesas,r8a774c0-pcie-ep",
+ "renesas,rcar-gen3-pcie-ep";
+ reg = <0 0xfe000000 0 0x80000>,
+ <0x0 0xfe100000 0 0x100000>,
+ <0x0 0xfe200000 0 0x200000>,
+ <0x0 0x30000000 0 0x8000000>,
+ <0x0 0x38000000 0 0x8000000>;
+ reg-names = "apb-base", "memory0", "memory1", "memory2", "memory3";
+ resets = <&cpg 319>;
+ power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>;
+ clocks = <&cpg CPG_MOD 319>;
+ clock-names = "pcie";
+ max-functions = /bits/ 8 <1>;
+ };
--
2.20.1

2020-01-08 18:47:11

by Lad, Prabhakar

[permalink] [raw]
Subject: [v3 1/6] PCI: rcar: Preparation for adding endpoint support

Prepare for adding endpoint support to rcar controller, there are no
functional changes with this patch, a common file is created so that
it can be shared with endpoint driver.

Signed-off-by: Lad Prabhakar <[email protected]>
---
arch/arm64/configs/defconfig | 2 +-
drivers/pci/controller/Kconfig | 4 +-
drivers/pci/controller/Makefile | 2 +-
drivers/pci/controller/pcie-rcar-host.c | 1044 +++++++++++++++++++
drivers/pci/controller/pcie-rcar.c | 1229 +----------------------
drivers/pci/controller/pcie-rcar.h | 126 +++
6 files changed, 1227 insertions(+), 1180 deletions(-)
create mode 100644 drivers/pci/controller/pcie-rcar-host.c
create mode 100644 drivers/pci/controller/pcie-rcar.h

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 6a83ba2aea3e..49d973c6c034 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -182,7 +182,7 @@ CONFIG_HOTPLUG_PCI=y
CONFIG_HOTPLUG_PCI_ACPI=y
CONFIG_PCI_AARDVARK=y
CONFIG_PCI_TEGRA=y
-CONFIG_PCIE_RCAR=y
+CONFIG_PCIE_RCAR_HOST=y
CONFIG_PCI_HOST_GENERIC=y
CONFIG_PCI_XGENE=y
CONFIG_PCIE_ALTERA=y
diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
index 24f9bcb8ba4b..b022ac5678f7 100644
--- a/drivers/pci/controller/Kconfig
+++ b/drivers/pci/controller/Kconfig
@@ -54,12 +54,12 @@ config PCI_RCAR_GEN2
There are 3 internal PCI controllers available with a single
built-in EHCI/OHCI host controller present on each one.

-config PCIE_RCAR
+config PCIE_RCAR_HOST
bool "Renesas R-Car PCIe controller"
depends on ARCH_RENESAS || COMPILE_TEST
depends on PCI_MSI_IRQ_DOMAIN
help
- Say Y here if you want PCIe controller support on R-Car SoCs.
+ Say Y here if you want PCIe controller support on R-Car SoCs in host mode.

config PCI_HOST_COMMON
bool
diff --git a/drivers/pci/controller/Makefile b/drivers/pci/controller/Makefile
index 3d4f597f15ce..69ba1dbf837b 100644
--- a/drivers/pci/controller/Makefile
+++ b/drivers/pci/controller/Makefile
@@ -7,7 +7,7 @@ obj-$(CONFIG_PCI_MVEBU) += pci-mvebu.o
obj-$(CONFIG_PCI_AARDVARK) += pci-aardvark.o
obj-$(CONFIG_PCI_TEGRA) += pci-tegra.o
obj-$(CONFIG_PCI_RCAR_GEN2) += pci-rcar-gen2.o
-obj-$(CONFIG_PCIE_RCAR) += pcie-rcar.o
+obj-$(CONFIG_PCIE_RCAR_HOST) += pcie-rcar.o pcie-rcar-host.o
obj-$(CONFIG_PCI_HOST_COMMON) += pci-host-common.o
obj-$(CONFIG_PCI_HOST_GENERIC) += pci-host-generic.o
obj-$(CONFIG_PCIE_XILINX) += pcie-xilinx.o
diff --git a/drivers/pci/controller/pcie-rcar-host.c b/drivers/pci/controller/pcie-rcar-host.c
new file mode 100644
index 000000000000..35cdac2a6dd2
--- /dev/null
+++ b/drivers/pci/controller/pcie-rcar-host.c
@@ -0,0 +1,1044 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * PCIe driver for Renesas R-Car SoCs
+ * Copyright (C) 2014-2020 Renesas Electronics Europe Ltd
+ *
+ * Based on:
+ * arch/sh/drivers/pci/pcie-sh7786.c
+ * arch/sh/drivers/pci/ops-sh7786.c
+ * Copyright (C) 2009-2011 Paul Mundt
+ *
+ * Author: Phil Edworthy <[email protected]>
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/msi.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_pci.h>
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+#include <linux/phy/phy.h>
+
+#include "pcie-rcar.h"
+
+struct rcar_msi {
+ DECLARE_BITMAP(used, INT_PCI_MSI_NR);
+ struct irq_domain *domain;
+ struct msi_controller chip;
+ unsigned long pages;
+ struct mutex lock;
+ int irq1;
+ int irq2;
+};
+
+static inline struct rcar_msi *to_rcar_msi(struct msi_controller *chip)
+{
+ return container_of(chip, struct rcar_msi, chip);
+}
+
+/* Structure representing the PCIe interface */
+struct rcar_pcie {
+ struct device *dev;
+ struct phy *phy;
+ void __iomem *base;
+ struct list_head resources;
+ int root_bus_nr;
+ struct clk *bus_clk;
+ struct rcar_msi msi;
+};
+
+static u32 rcar_read_conf(struct rcar_pcie *pcie, int where)
+{
+ unsigned int shift = BITS_PER_BYTE * (where & 3);
+ u32 val = rcar_pci_read_reg(pcie->base, where & ~3);
+
+ return val >> shift;
+}
+
+/* Serialization is provided by 'pci_lock' in drivers/pci/access.c */
+static int rcar_pcie_config_access(struct rcar_pcie *pcie,
+ unsigned char access_type, struct pci_bus *bus,
+ unsigned int devfn, int where, u32 *data)
+{
+ unsigned int dev, func, reg, index;
+
+ dev = PCI_SLOT(devfn);
+ func = PCI_FUNC(devfn);
+ reg = where & ~3;
+ index = reg / 4;
+
+ /*
+ * While each channel has its own memory-mapped extended config
+ * space, it's generally only accessible when in endpoint mode.
+ * When in root complex mode, the controller is unable to target
+ * itself with either type 0 or type 1 accesses, and indeed, any
+ * controller initiated target transfer to its own config space
+ * result in a completer abort.
+ *
+ * Each channel effectively only supports a single device, but as
+ * the same channel <-> device access works for any PCI_SLOT()
+ * value, we cheat a bit here and bind the controller's config
+ * space to devfn 0 in order to enable self-enumeration. In this
+ * case the regular ECAR/ECDR path is sidelined and the mangled
+ * config access itself is initiated as an internal bus transaction.
+ */
+ if (pci_is_root_bus(bus)) {
+ if (dev != 0)
+ return PCIBIOS_DEVICE_NOT_FOUND;
+
+ if (access_type == RCAR_PCI_ACCESS_READ) {
+ *data = rcar_pci_read_reg(pcie->base, PCICONF(index));
+ } else {
+ /* Keep an eye out for changes to the root bus number */
+ if (pci_is_root_bus(bus) && (reg == PCI_PRIMARY_BUS))
+ pcie->root_bus_nr = *data & 0xff;
+
+ rcar_pci_write_reg(pcie->base, *data, PCICONF(index));
+ }
+
+ return PCIBIOS_SUCCESSFUL;
+ }
+
+ if (pcie->root_bus_nr < 0)
+ return PCIBIOS_DEVICE_NOT_FOUND;
+
+ /* Clear errors */
+ rcar_pci_write_reg(pcie->base, rcar_pci_read_reg(pcie->base, PCIEERRFR),
+ PCIEERRFR);
+
+ /* Set the PIO address */
+ rcar_pci_write_reg(pcie->base, PCIE_CONF_BUS(bus->number) |
+ PCIE_CONF_DEV(dev) | PCIE_CONF_FUNC(func) | reg, PCIECAR);
+
+ /* Enable the configuration access */
+ if (bus->parent->number == pcie->root_bus_nr)
+ rcar_pci_write_reg(pcie->base, CONFIG_SEND_ENABLE | TYPE0,
+ PCIECCTLR);
+ else
+ rcar_pci_write_reg(pcie->base, CONFIG_SEND_ENABLE | TYPE1,
+ PCIECCTLR);
+
+ /* Check for errors */
+ if (rcar_pci_read_reg(pcie->base, PCIEERRFR) & UNSUPPORTED_REQUEST)
+ return PCIBIOS_DEVICE_NOT_FOUND;
+
+ /* Check for master and target aborts */
+ if (rcar_read_conf(pcie, RCONF(PCI_STATUS)) &
+ (PCI_STATUS_REC_MASTER_ABORT | PCI_STATUS_REC_TARGET_ABORT))
+ return PCIBIOS_DEVICE_NOT_FOUND;
+
+ if (access_type == RCAR_PCI_ACCESS_READ)
+ *data = rcar_pci_read_reg(pcie->base, PCIECDR);
+ else
+ rcar_pci_write_reg(pcie->base, *data, PCIECDR);
+
+ /* Disable the configuration access */
+ rcar_pci_write_reg(pcie->base, 0, PCIECCTLR);
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+static int rcar_pcie_read_conf(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 *val)
+{
+ struct rcar_pcie *pcie = bus->sysdata;
+ int ret;
+
+ ret = rcar_pcie_config_access(pcie, RCAR_PCI_ACCESS_READ,
+ bus, devfn, where, val);
+ if (ret != PCIBIOS_SUCCESSFUL) {
+ *val = 0xffffffff;
+ return ret;
+ }
+
+ if (size == 1)
+ *val = (*val >> (BITS_PER_BYTE * (where & 3))) & 0xff;
+ else if (size == 2)
+ *val = (*val >> (BITS_PER_BYTE * (where & 2))) & 0xffff;
+
+ dev_dbg(&bus->dev, "pcie-config-read: bus=%3d devfn=0x%04x where=0x%04x size=%d val=0x%08x\n",
+ bus->number, devfn, where, size, *val);
+
+ return ret;
+}
+
+/* Serialization is provided by 'pci_lock' in drivers/pci/access.c */
+static int rcar_pcie_write_conf(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 val)
+{
+ struct rcar_pcie *pcie = bus->sysdata;
+ unsigned int shift;
+ u32 data;
+ int ret;
+
+ ret = rcar_pcie_config_access(pcie, RCAR_PCI_ACCESS_READ,
+ bus, devfn, where, &data);
+ if (ret != PCIBIOS_SUCCESSFUL)
+ return ret;
+
+ dev_dbg(&bus->dev, "pcie-config-write: bus=%3d devfn=0x%04x where=0x%04x size=%d val=0x%08x\n",
+ bus->number, devfn, where, size, val);
+
+ if (size == 1) {
+ shift = BITS_PER_BYTE * (where & 3);
+ data &= ~(0xff << shift);
+ data |= ((val & 0xff) << shift);
+ } else if (size == 2) {
+ shift = BITS_PER_BYTE * (where & 2);
+ data &= ~(0xffff << shift);
+ data |= ((val & 0xffff) << shift);
+ } else
+ data = val;
+
+ ret = rcar_pcie_config_access(pcie, RCAR_PCI_ACCESS_WRITE,
+ bus, devfn, where, &data);
+
+ return ret;
+}
+
+static struct pci_ops rcar_pcie_ops = {
+ .read = rcar_pcie_read_conf,
+ .write = rcar_pcie_write_conf,
+};
+
+static int rcar_pcie_setup(struct list_head *resource, struct rcar_pcie *pci)
+{
+ struct resource_entry *win;
+ int i = 0;
+
+ /* Setup PCI resources */
+ resource_list_for_each_entry(win, &pci->resources) {
+ struct resource *res = win->res;
+
+ if (!res->flags)
+ continue;
+
+ switch (resource_type(res)) {
+ case IORESOURCE_IO:
+ case IORESOURCE_MEM:
+ rcar_pcie_set_outbound(i, pci->base, res, true);
+ i++;
+ break;
+ case IORESOURCE_BUS:
+ pci->root_bus_nr = res->start;
+ break;
+ default:
+ continue;
+ }
+
+ pci_add_resource(resource, res);
+ }
+
+ return 1;
+}
+
+static void rcar_pcie_force_speedup(struct rcar_pcie *pcie)
+{
+ struct device *dev = pcie->dev;
+ unsigned int timeout = 1000;
+ u32 macsr;
+
+ if ((rcar_pci_read_reg(pcie->base, MACS2R) & LINK_SPEED) !=
+ LINK_SPEED_5_0GTS)
+ return;
+
+ if (rcar_pci_read_reg(pcie->base, MACCTLR) & SPEED_CHANGE) {
+ dev_err(dev, "Speed change already in progress\n");
+ return;
+ }
+
+ macsr = rcar_pci_read_reg(pcie->base, MACSR);
+ if ((macsr & LINK_SPEED) == LINK_SPEED_5_0GTS)
+ goto done;
+
+ /* Set target link speed to 5.0 GT/s */
+ rcar_rmw32(pcie->base, EXPCAP(12), PCI_EXP_LNKSTA_CLS,
+ PCI_EXP_LNKSTA_CLS_5_0GB);
+
+ /* Set speed change reason as intentional factor */
+ rcar_rmw32(pcie->base, MACCGSPSETR, SPCNGRSN, 0);
+
+ /* Clear SPCHGFIN, SPCHGSUC, and SPCHGFAIL */
+ if (macsr & (SPCHGFIN | SPCHGSUC | SPCHGFAIL))
+ rcar_pci_write_reg(pcie->base, macsr, MACSR);
+
+ /* Start link speed change */
+ rcar_rmw32(pcie->base, MACCTLR, SPEED_CHANGE, SPEED_CHANGE);
+
+ while (timeout--) {
+ macsr = rcar_pci_read_reg(pcie->base, MACSR);
+ if (macsr & SPCHGFIN) {
+ /* Clear the interrupt bits */
+ rcar_pci_write_reg(pcie->base, macsr, MACSR);
+
+ if (macsr & SPCHGFAIL)
+ dev_err(dev, "Speed change failed\n");
+
+ goto done;
+ }
+
+ msleep(1);
+ }
+
+ dev_err(dev, "Speed change timed out\n");
+
+done:
+ dev_info(dev, "Current link speed is %s GT/s\n",
+ (macsr & LINK_SPEED) == LINK_SPEED_5_0GTS ? "5" : "2.5");
+}
+
+static int rcar_pcie_enable(struct rcar_pcie *pcie)
+{
+ struct device *dev = pcie->dev;
+ struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
+ struct pci_bus *bus, *child;
+ int ret;
+
+ /* Try setting 5 GT/s link speed */
+ rcar_pcie_force_speedup(pcie);
+
+ rcar_pcie_setup(&bridge->windows, pcie);
+
+ pci_add_flags(PCI_REASSIGN_ALL_BUS);
+
+ bridge->dev.parent = dev;
+ bridge->sysdata = pcie;
+ bridge->busnr = pcie->root_bus_nr;
+ bridge->ops = &rcar_pcie_ops;
+ bridge->map_irq = of_irq_parse_and_map_pci;
+ bridge->swizzle_irq = pci_common_swizzle;
+ if (IS_ENABLED(CONFIG_PCI_MSI))
+ bridge->msi = &pcie->msi.chip;
+
+ ret = pci_scan_root_bus_bridge(bridge);
+ if (ret < 0)
+ return ret;
+
+ bus = bridge->bus;
+
+ pci_bus_size_bridges(bus);
+ pci_bus_assign_resources(bus);
+
+ list_for_each_entry(child, &bus->children, node)
+ pcie_bus_configure_settings(child);
+
+ pci_bus_add_devices(bus);
+
+ return 0;
+}
+
+static int phy_wait_for_ack(struct rcar_pcie *pcie)
+{
+ struct device *dev = pcie->dev;
+ unsigned int timeout = 100;
+
+ while (timeout--) {
+ if (rcar_pci_read_reg(pcie->base, H1_PCIEPHYADRR) & PHY_ACK)
+ return 0;
+
+ udelay(100);
+ }
+
+ dev_err(dev, "Access to PCIe phy timed out\n");
+
+ return -ETIMEDOUT;
+}
+
+static void phy_write_reg(struct rcar_pcie *pcie,
+ unsigned int rate, u32 addr,
+ unsigned int lane, u32 data)
+{
+ u32 phyaddr;
+
+ phyaddr = WRITE_CMD |
+ ((rate & 1) << RATE_POS) |
+ ((lane & 0xf) << LANE_POS) |
+ ((addr & 0xff) << ADR_POS);
+
+ /* Set write data */
+ rcar_pci_write_reg(pcie->base, data, H1_PCIEPHYDOUTR);
+ rcar_pci_write_reg(pcie->base, phyaddr, H1_PCIEPHYADRR);
+
+ /* Ignore errors as they will be dealt with if the data link is down */
+ phy_wait_for_ack(pcie);
+
+ /* Clear command */
+ rcar_pci_write_reg(pcie->base, 0, H1_PCIEPHYDOUTR);
+ rcar_pci_write_reg(pcie->base, 0, H1_PCIEPHYADRR);
+
+ /* Ignore errors as they will be dealt with if the data link is down */
+ phy_wait_for_ack(pcie);
+}
+
+static int rcar_pcie_hw_init(struct rcar_pcie *pcie)
+{
+ int err;
+
+ /* Begin initialization */
+ rcar_pci_write_reg(pcie->base, 0, PCIETCTLR);
+
+ /* Set mode */
+ rcar_pci_write_reg(pcie->base, 1, PCIEMSR);
+
+ err = rcar_pcie_wait_for_phyrdy(pcie->base);
+ if (err)
+ return err;
+
+ /*
+ * Initial header for port config space is type 1, set the device
+ * class to match. Hardware takes care of propagating the IDSETR
+ * settings, so there is no need to bother with a quirk.
+ */
+ rcar_pci_write_reg(pcie->base, PCI_CLASS_BRIDGE_PCI << 16, IDSETR1);
+
+ /*
+ * Setup Secondary Bus Number & Subordinate Bus Number, even though
+ * they aren't used, to avoid bridge being detected as broken.
+ */
+ rcar_rmw32(pcie->base, RCONF(PCI_SECONDARY_BUS), 0xff, 1);
+ rcar_rmw32(pcie->base, RCONF(PCI_SUBORDINATE_BUS), 0xff, 1);
+
+ /* Initialize default capabilities. */
+ rcar_rmw32(pcie->base, REXPCAP(0), 0xff, PCI_CAP_ID_EXP);
+ rcar_rmw32(pcie->base, REXPCAP(PCI_EXP_FLAGS),
+ PCI_EXP_FLAGS_TYPE, PCI_EXP_TYPE_ROOT_PORT << 4);
+ rcar_rmw32(pcie->base, RCONF(PCI_HEADER_TYPE), 0x7f,
+ PCI_HEADER_TYPE_BRIDGE);
+
+ /* Enable data link layer active state reporting */
+ rcar_rmw32(pcie->base, REXPCAP(PCI_EXP_LNKCAP), PCI_EXP_LNKCAP_DLLLARC,
+ PCI_EXP_LNKCAP_DLLLARC);
+
+ /* Write out the physical slot number = 0 */
+ rcar_rmw32(pcie->base, REXPCAP(PCI_EXP_SLTCAP), PCI_EXP_SLTCAP_PSN, 0);
+
+ /* Set the completion timer timeout to the maximum 50ms. */
+ rcar_rmw32(pcie->base, TLCTLR + 1, 0x3f, 50);
+
+ /* Terminate list of capabilities (Next Capability Offset=0) */
+ rcar_rmw32(pcie->base, RVCCAP(0), 0xfff00000, 0);
+
+ /* Enable MSI */
+ if (IS_ENABLED(CONFIG_PCI_MSI))
+ rcar_pci_write_reg(pcie->base, 0x801f0000, PCIEMSITXR);
+
+ rcar_pci_write_reg(pcie->base, MACCTLR_INIT_VAL, MACCTLR);
+
+ /* Finish initialization - establish a PCI Express link */
+ rcar_pci_write_reg(pcie->base, CFINIT, PCIETCTLR);
+
+ /* This will timeout if we don't have a link. */
+ err = rcar_pcie_wait_for_dl(pcie->base);
+ if (err)
+ return err;
+
+ /* Enable INTx interrupts */
+ rcar_rmw32(pcie->base, PCIEINTXR, 0, 0xF << 8);
+
+ wmb();
+
+ return 0;
+}
+
+static int rcar_pcie_phy_init_h1(struct rcar_pcie *pcie)
+{
+ /* Initialize the phy */
+ phy_write_reg(pcie, 0, 0x42, 0x1, 0x0EC34191);
+ phy_write_reg(pcie, 1, 0x42, 0x1, 0x0EC34180);
+ phy_write_reg(pcie, 0, 0x43, 0x1, 0x00210188);
+ phy_write_reg(pcie, 1, 0x43, 0x1, 0x00210188);
+ phy_write_reg(pcie, 0, 0x44, 0x1, 0x015C0014);
+ phy_write_reg(pcie, 1, 0x44, 0x1, 0x015C0014);
+ phy_write_reg(pcie, 1, 0x4C, 0x1, 0x786174A0);
+ phy_write_reg(pcie, 1, 0x4D, 0x1, 0x048000BB);
+ phy_write_reg(pcie, 0, 0x51, 0x1, 0x079EC062);
+ phy_write_reg(pcie, 0, 0x52, 0x1, 0x20000000);
+ phy_write_reg(pcie, 1, 0x52, 0x1, 0x20000000);
+ phy_write_reg(pcie, 1, 0x56, 0x1, 0x00003806);
+
+ phy_write_reg(pcie, 0, 0x60, 0x1, 0x004B03A5);
+ phy_write_reg(pcie, 0, 0x64, 0x1, 0x3F0F1F0F);
+ phy_write_reg(pcie, 0, 0x66, 0x1, 0x00008000);
+
+ return 0;
+}
+
+static int rcar_pcie_phy_init_gen2(struct rcar_pcie *pcie)
+{
+ /*
+ * These settings come from the R-Car Series, 2nd Generation User's
+ * Manual, section 50.3.1 (2) Initialization of the physical layer.
+ */
+ rcar_pci_write_reg(pcie->base, 0x000f0030, GEN2_PCIEPHYADDR);
+ rcar_pci_write_reg(pcie->base, 0x00381203, GEN2_PCIEPHYDATA);
+ rcar_pci_write_reg(pcie->base, 0x00000001, GEN2_PCIEPHYCTRL);
+ rcar_pci_write_reg(pcie->base, 0x00000006, GEN2_PCIEPHYCTRL);
+
+ rcar_pci_write_reg(pcie->base, 0x000f0054, GEN2_PCIEPHYADDR);
+ /* The following value is for DC connection, no termination resistor */
+ rcar_pci_write_reg(pcie->base, 0x13802007, GEN2_PCIEPHYDATA);
+ rcar_pci_write_reg(pcie->base, 0x00000001, GEN2_PCIEPHYCTRL);
+ rcar_pci_write_reg(pcie->base, 0x00000006, GEN2_PCIEPHYCTRL);
+
+ return 0;
+}
+
+static int rcar_pcie_phy_init_gen3(struct rcar_pcie *pcie)
+{
+ int err;
+
+ err = phy_init(pcie->phy);
+ if (err)
+ return err;
+
+ err = phy_power_on(pcie->phy);
+ if (err)
+ phy_exit(pcie->phy);
+
+ return err;
+}
+
+static int rcar_msi_alloc(struct rcar_msi *chip)
+{
+ int msi;
+
+ mutex_lock(&chip->lock);
+
+ msi = find_first_zero_bit(chip->used, INT_PCI_MSI_NR);
+ if (msi < INT_PCI_MSI_NR)
+ set_bit(msi, chip->used);
+ else
+ msi = -ENOSPC;
+
+ mutex_unlock(&chip->lock);
+
+ return msi;
+}
+
+static int rcar_msi_alloc_region(struct rcar_msi *chip, int no_irqs)
+{
+ int msi;
+
+ mutex_lock(&chip->lock);
+ msi = bitmap_find_free_region(chip->used, INT_PCI_MSI_NR,
+ order_base_2(no_irqs));
+ mutex_unlock(&chip->lock);
+
+ return msi;
+}
+
+static void rcar_msi_free(struct rcar_msi *chip, unsigned long irq)
+{
+ mutex_lock(&chip->lock);
+ clear_bit(irq, chip->used);
+ mutex_unlock(&chip->lock);
+}
+
+static irqreturn_t rcar_pcie_msi_irq(int irq, void *data)
+{
+ struct rcar_pcie *pcie = data;
+ struct rcar_msi *msi = &pcie->msi;
+ struct device *dev = pcie->dev;
+ unsigned long reg;
+
+ reg = rcar_pci_read_reg(pcie->base, PCIEMSIFR);
+
+ /* MSI & INTx share an interrupt - we only handle MSI here */
+ if (!reg)
+ return IRQ_NONE;
+
+ while (reg) {
+ unsigned int index = find_first_bit(&reg, 32);
+ unsigned int msi_irq;
+
+ /* clear the interrupt */
+ rcar_pci_write_reg(pcie->base, 1 << index, PCIEMSIFR);
+
+ msi_irq = irq_find_mapping(msi->domain, index);
+ if (msi_irq) {
+ if (test_bit(index, msi->used))
+ generic_handle_irq(msi_irq);
+ else
+ dev_info(dev, "unhandled MSI\n");
+ } else {
+ /* Unknown MSI, just clear it */
+ dev_dbg(dev, "unexpected MSI\n");
+ }
+
+ /* see if there's any more pending in this vector */
+ reg = rcar_pci_read_reg(pcie->base, PCIEMSIFR);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int rcar_msi_setup_irq(struct msi_controller *chip, struct pci_dev *pdev,
+ struct msi_desc *desc)
+{
+ struct rcar_msi *msi = to_rcar_msi(chip);
+ struct rcar_pcie *pcie = container_of(chip, struct rcar_pcie, msi.chip);
+ struct msi_msg msg;
+ unsigned int irq;
+ int hwirq;
+
+ hwirq = rcar_msi_alloc(msi);
+ if (hwirq < 0)
+ return hwirq;
+
+ irq = irq_find_mapping(msi->domain, hwirq);
+ if (!irq) {
+ rcar_msi_free(msi, hwirq);
+ return -EINVAL;
+ }
+
+ irq_set_msi_desc(irq, desc);
+
+ msg.address_lo = rcar_pci_read_reg(pcie->base, PCIEMSIALR) & ~MSIFE;
+ msg.address_hi = rcar_pci_read_reg(pcie->base, PCIEMSIAUR);
+ msg.data = hwirq;
+
+ pci_write_msi_msg(irq, &msg);
+
+ return 0;
+}
+
+static int rcar_msi_setup_irqs(struct msi_controller *chip,
+ struct pci_dev *pdev, int nvec, int type)
+{
+ struct rcar_pcie *pcie = container_of(chip, struct rcar_pcie, msi.chip);
+ struct rcar_msi *msi = to_rcar_msi(chip);
+ struct msi_desc *desc;
+ struct msi_msg msg;
+ unsigned int irq;
+ int hwirq;
+ int i;
+
+ /* MSI-X interrupts are not supported */
+ if (type == PCI_CAP_ID_MSIX)
+ return -EINVAL;
+
+ WARN_ON(!list_is_singular(&pdev->dev.msi_list));
+ desc = list_entry(pdev->dev.msi_list.next, struct msi_desc, list);
+
+ hwirq = rcar_msi_alloc_region(msi, nvec);
+ if (hwirq < 0)
+ return -ENOSPC;
+
+ irq = irq_find_mapping(msi->domain, hwirq);
+ if (!irq)
+ return -ENOSPC;
+
+ for (i = 0; i < nvec; i++) {
+ /*
+ * irq_create_mapping() called from rcar_pcie_probe() pre-
+ * allocates descs, so there is no need to allocate descs here.
+ * We can therefore assume that if irq_find_mapping() above
+ * returns non-zero, then the descs are also successfully
+ * allocated.
+ */
+ if (irq_set_msi_desc_off(irq, i, desc)) {
+ /* TODO: clear */
+ return -EINVAL;
+ }
+ }
+
+ desc->nvec_used = nvec;
+ desc->msi_attrib.multiple = order_base_2(nvec);
+
+ msg.address_lo = rcar_pci_read_reg(pcie->base, PCIEMSIALR) & ~MSIFE;
+ msg.address_hi = rcar_pci_read_reg(pcie->base, PCIEMSIAUR);
+ msg.data = hwirq;
+
+ pci_write_msi_msg(irq, &msg);
+
+ return 0;
+}
+
+static void rcar_msi_teardown_irq(struct msi_controller *chip, unsigned int irq)
+{
+ struct rcar_msi *msi = to_rcar_msi(chip);
+ struct irq_data *d = irq_get_irq_data(irq);
+
+ rcar_msi_free(msi, d->hwirq);
+}
+
+static struct irq_chip rcar_msi_irq_chip = {
+ .name = "R-Car PCIe MSI",
+ .irq_enable = pci_msi_unmask_irq,
+ .irq_disable = pci_msi_mask_irq,
+ .irq_mask = pci_msi_mask_irq,
+ .irq_unmask = pci_msi_unmask_irq,
+};
+
+static int rcar_msi_map(struct irq_domain *domain, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ irq_set_chip_and_handler(irq, &rcar_msi_irq_chip, handle_simple_irq);
+ irq_set_chip_data(irq, domain->host_data);
+
+ return 0;
+}
+
+static const struct irq_domain_ops msi_domain_ops = {
+ .map = rcar_msi_map,
+};
+
+static void rcar_pcie_unmap_msi(struct rcar_pcie *pcie)
+{
+ struct rcar_msi *msi = &pcie->msi;
+ int i, irq;
+
+ for (i = 0; i < INT_PCI_MSI_NR; i++) {
+ irq = irq_find_mapping(msi->domain, i);
+ if (irq > 0)
+ irq_dispose_mapping(irq);
+ }
+
+ irq_domain_remove(msi->domain);
+}
+
+static int rcar_pcie_enable_msi(struct rcar_pcie *pcie)
+{
+ struct rcar_msi *msi = &pcie->msi;
+ struct device *dev = pcie->dev;
+ phys_addr_t base;
+ int err, i;
+
+ mutex_init(&msi->lock);
+
+ msi->chip.dev = dev;
+ msi->chip.setup_irq = rcar_msi_setup_irq;
+ msi->chip.setup_irqs = rcar_msi_setup_irqs;
+ msi->chip.teardown_irq = rcar_msi_teardown_irq;
+
+ msi->domain = irq_domain_add_linear(dev->of_node, INT_PCI_MSI_NR,
+ &msi_domain_ops, &msi->chip);
+ if (!msi->domain) {
+ dev_err(dev, "failed to create IRQ domain\n");
+ return -ENOMEM;
+ }
+
+ for (i = 0; i < INT_PCI_MSI_NR; i++)
+ irq_create_mapping(msi->domain, i);
+
+ /* Two irqs are for MSI, but they are also used for non-MSI irqs */
+ err = devm_request_irq(dev, msi->irq1, rcar_pcie_msi_irq,
+ IRQF_SHARED | IRQF_NO_THREAD,
+ rcar_msi_irq_chip.name, pcie);
+ if (err < 0) {
+ dev_err(dev, "failed to request IRQ: %d\n", err);
+ goto err;
+ }
+
+ err = devm_request_irq(dev, msi->irq2, rcar_pcie_msi_irq,
+ IRQF_SHARED | IRQF_NO_THREAD,
+ rcar_msi_irq_chip.name, pcie);
+ if (err < 0) {
+ dev_err(dev, "failed to request IRQ: %d\n", err);
+ goto err;
+ }
+
+ /* setup MSI data target */
+ msi->pages = __get_free_pages(GFP_KERNEL, 0);
+ if (!msi->pages) {
+ err = -ENOMEM;
+ goto err;
+ }
+ base = virt_to_phys((void *)msi->pages);
+
+ rcar_pci_write_reg(pcie->base, lower_32_bits(base) | MSIFE, PCIEMSIALR);
+ rcar_pci_write_reg(pcie->base, upper_32_bits(base), PCIEMSIAUR);
+
+ /* enable all MSI interrupts */
+ rcar_pci_write_reg(pcie->base, 0xffffffff, PCIEMSIIER);
+
+ return 0;
+
+err:
+ rcar_pcie_unmap_msi(pcie);
+ return err;
+}
+
+static void rcar_pcie_teardown_msi(struct rcar_pcie *pcie)
+{
+ struct rcar_msi *msi = &pcie->msi;
+
+ /* Disable all MSI interrupts */
+ rcar_pci_write_reg(pcie->base, 0, PCIEMSIIER);
+
+ /* Disable address decoding of the MSI interrupt, MSIFE */
+ rcar_pci_write_reg(pcie->base, 0, PCIEMSIALR);
+
+ free_pages(msi->pages, 0);
+
+ rcar_pcie_unmap_msi(pcie);
+}
+
+static int rcar_pcie_get_resources(struct rcar_pcie *pcie)
+{
+ struct device *dev = pcie->dev;
+ struct resource res;
+ int err, i;
+
+ pcie->phy = devm_phy_optional_get(dev, "pcie");
+ if (IS_ERR(pcie->phy))
+ return PTR_ERR(pcie->phy);
+
+ err = of_address_to_resource(dev->of_node, 0, &res);
+ if (err)
+ return err;
+
+ pcie->base = devm_ioremap_resource(dev, &res);
+ if (IS_ERR(pcie->base))
+ return PTR_ERR(pcie->base);
+
+ pcie->bus_clk = devm_clk_get(dev, "pcie_bus");
+ if (IS_ERR(pcie->bus_clk)) {
+ dev_err(dev, "cannot get pcie bus clock\n");
+ return PTR_ERR(pcie->bus_clk);
+ }
+
+ i = irq_of_parse_and_map(dev->of_node, 0);
+ if (!i) {
+ dev_err(dev, "cannot get platform resources for msi interrupt\n");
+ err = -ENOENT;
+ goto err_irq1;
+ }
+ pcie->msi.irq1 = i;
+
+ i = irq_of_parse_and_map(dev->of_node, 1);
+ if (!i) {
+ dev_err(dev, "cannot get platform resources for msi interrupt\n");
+ err = -ENOENT;
+ goto err_irq2;
+ }
+ pcie->msi.irq2 = i;
+
+ return 0;
+
+err_irq2:
+ irq_dispose_mapping(pcie->msi.irq1);
+err_irq1:
+ return err;
+}
+
+static int rcar_pcie_inbound_ranges(struct rcar_pcie *pcie,
+ struct resource_entry *entry,
+ int *index)
+{
+ u64 restype = entry->res->flags;
+ u64 cpu_addr = entry->res->start;
+ u64 cpu_end = entry->res->end;
+ u64 pci_addr = entry->res->start - entry->offset;
+ u32 flags = LAM_64BIT | LAR_ENABLE;
+ u64 mask;
+ u64 size = resource_size(entry->res);
+ int idx = *index;
+
+ if (restype & IORESOURCE_PREFETCH)
+ flags |= LAM_PREFETCH;
+
+ while (cpu_addr < cpu_end) {
+ if (idx >= MAX_NR_INBOUND_MAPS - 1) {
+ dev_err(pcie->dev, "Failed to map inbound regions!\n");
+ return -EINVAL;
+ }
+ /*
+ * If the size of the range is larger than the alignment of
+ * the start address, we have to use multiple entries to
+ * perform the mapping.
+ */
+ if (cpu_addr > 0) {
+ unsigned long nr_zeros = __ffs64(cpu_addr);
+ u64 alignment = 1ULL << nr_zeros;
+
+ size = min(size, alignment);
+ }
+ /* Hardware supports max 4GiB inbound region */
+ size = min(size, 1ULL << 32);
+
+ mask = roundup_pow_of_two(size) - 1;
+ mask &= ~0xf;
+
+ rcar_pcie_set_inbound(pcie->base, cpu_addr, pci_addr,
+ mask | flags, idx, true);
+
+ pci_addr += size;
+ cpu_addr += size;
+ idx += 2;
+ }
+ *index = idx;
+
+ return 0;
+}
+
+static int rcar_pcie_parse_map_dma_ranges(struct rcar_pcie *pcie)
+{
+ struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
+ struct resource_entry *entry;
+ int index = 0, err = 0;
+
+ resource_list_for_each_entry(entry, &bridge->dma_ranges) {
+ err = rcar_pcie_inbound_ranges(pcie, entry, &index);
+ if (err)
+ break;
+ }
+
+ return err;
+}
+
+static const struct of_device_id rcar_pcie_of_match[] = {
+ { .compatible = "renesas,pcie-r8a7779",
+ .data = rcar_pcie_phy_init_h1 },
+ { .compatible = "renesas,pcie-r8a7790",
+ .data = rcar_pcie_phy_init_gen2 },
+ { .compatible = "renesas,pcie-r8a7791",
+ .data = rcar_pcie_phy_init_gen2 },
+ { .compatible = "renesas,pcie-rcar-gen2",
+ .data = rcar_pcie_phy_init_gen2 },
+ { .compatible = "renesas,pcie-r8a7795",
+ .data = rcar_pcie_phy_init_gen3 },
+ { .compatible = "renesas,pcie-rcar-gen3",
+ .data = rcar_pcie_phy_init_gen3 },
+ {},
+};
+
+static int rcar_pcie_probe(struct platform_device *pdev)
+{
+ int (*phy_init_fn)(struct rcar_pcie *pcie);
+ struct device *dev = &pdev->dev;
+ struct pci_host_bridge *bridge;
+ struct rcar_pcie *pcie;
+ u32 data;
+ int err;
+
+ bridge = pci_alloc_host_bridge(sizeof(*pcie));
+ if (!bridge)
+ return -ENOMEM;
+
+ pcie = pci_host_bridge_priv(bridge);
+
+ pcie->dev = dev;
+ platform_set_drvdata(pdev, pcie);
+
+ err = pci_parse_request_of_pci_ranges(dev, &pcie->resources,
+ &bridge->dma_ranges, NULL);
+ if (err)
+ goto err_free_bridge;
+
+ pm_runtime_enable(pcie->dev);
+ err = pm_runtime_get_sync(pcie->dev);
+ if (err < 0) {
+ dev_err(pcie->dev, "pm_runtime_get_sync failed\n");
+ goto err_pm_disable;
+ }
+
+ err = rcar_pcie_get_resources(pcie);
+ if (err < 0) {
+ dev_err(dev, "failed to request resources: %d\n", err);
+ goto err_pm_put;
+ }
+
+ err = clk_prepare_enable(pcie->bus_clk);
+ if (err) {
+ dev_err(dev, "failed to enable bus clock: %d\n", err);
+ goto err_unmap_msi_irqs;
+ }
+
+ err = rcar_pcie_parse_map_dma_ranges(pcie);
+ if (err)
+ goto err_clk_disable;
+
+ phy_init_fn = of_device_get_match_data(dev);
+ err = phy_init_fn(pcie);
+ if (err) {
+ dev_err(dev, "failed to init PCIe PHY\n");
+ goto err_clk_disable;
+ }
+
+ /* Failure to get a link might just be that no cards are inserted */
+ if (rcar_pcie_hw_init(pcie)) {
+ dev_info(dev, "PCIe link down\n");
+ err = -ENODEV;
+ goto err_phy_shutdown;
+ }
+
+ data = rcar_pci_read_reg(pcie->base, MACSR);
+ dev_info(dev, "PCIe x%d: link up\n", (data >> 20) & 0x3f);
+
+ if (IS_ENABLED(CONFIG_PCI_MSI)) {
+ err = rcar_pcie_enable_msi(pcie);
+ if (err < 0) {
+ dev_err(dev,
+ "failed to enable MSI support: %d\n",
+ err);
+ goto err_phy_shutdown;
+ }
+ }
+
+ err = rcar_pcie_enable(pcie);
+ if (err)
+ goto err_msi_teardown;
+
+ return 0;
+
+err_msi_teardown:
+ if (IS_ENABLED(CONFIG_PCI_MSI))
+ rcar_pcie_teardown_msi(pcie);
+
+err_phy_shutdown:
+ if (pcie->phy) {
+ phy_power_off(pcie->phy);
+ phy_exit(pcie->phy);
+ }
+
+err_clk_disable:
+ clk_disable_unprepare(pcie->bus_clk);
+
+err_unmap_msi_irqs:
+ irq_dispose_mapping(pcie->msi.irq2);
+ irq_dispose_mapping(pcie->msi.irq1);
+
+err_pm_put:
+ pm_runtime_put(dev);
+
+err_pm_disable:
+ pm_runtime_disable(dev);
+ pci_free_resource_list(&pcie->resources);
+
+err_free_bridge:
+ pci_free_host_bridge(bridge);
+
+ return err;
+}
+
+static int rcar_pcie_resume_noirq(struct device *dev)
+{
+ struct rcar_pcie *pcie = dev_get_drvdata(dev);
+
+ if (rcar_pci_read_reg(pcie->base, PMSR) &&
+ !(rcar_pci_read_reg(pcie->base, PCIETCTLR) & DL_DOWN))
+ return 0;
+
+ /* Re-establish the PCIe link */
+ rcar_pci_write_reg(pcie->base, MACCTLR_INIT_VAL, MACCTLR);
+ rcar_pci_write_reg(pcie->base, CFINIT, PCIETCTLR);
+ return rcar_pcie_wait_for_dl(pcie->base);
+}
+
+static const struct dev_pm_ops rcar_pcie_pm_ops = {
+ .resume_noirq = rcar_pcie_resume_noirq,
+};
+
+static struct platform_driver rcar_pcie_driver = {
+ .driver = {
+ .name = "rcar-pcie",
+ .of_match_table = rcar_pcie_of_match,
+ .pm = &rcar_pcie_pm_ops,
+ .suppress_bind_attrs = true,
+ },
+ .probe = rcar_pcie_probe,
+};
+builtin_platform_driver(rcar_pcie_driver);
diff --git a/drivers/pci/controller/pcie-rcar.c b/drivers/pci/controller/pcie-rcar.c
index 759c6542c5c8..d5568db27efc 100644
--- a/drivers/pci/controller/pcie-rcar.c
+++ b/drivers/pci/controller/pcie-rcar.c
@@ -1,7 +1,7 @@
// SPDX-License-Identifier: GPL-2.0
/*
* PCIe driver for Renesas R-Car SoCs
- * Copyright (C) 2014 Renesas Electronics Europe Ltd
+ * Copyright (C) 2014-2020 Renesas Electronics Europe Ltd
*
* Based on:
* arch/sh/drivers/pci/pcie-sh7786.c
@@ -11,336 +11,69 @@
* Author: Phil Edworthy <[email protected]>
*/

-#include <linux/bitops.h>
-#include <linux/clk.h>
#include <linux/delay.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/irqdomain.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/msi.h>
-#include <linux/of_address.h>
-#include <linux/of_irq.h>
-#include <linux/of_pci.h>
-#include <linux/of_platform.h>
#include <linux/pci.h>
-#include <linux/phy/phy.h>
-#include <linux/platform_device.h>
-#include <linux/pm_runtime.h>
-#include <linux/slab.h>

-#define PCIECAR 0x000010
-#define PCIECCTLR 0x000018
-#define CONFIG_SEND_ENABLE BIT(31)
-#define TYPE0 (0 << 8)
-#define TYPE1 BIT(8)
-#define PCIECDR 0x000020
-#define PCIEMSR 0x000028
-#define PCIEINTXR 0x000400
-#define PCIEPHYSR 0x0007f0
-#define PHYRDY BIT(0)
-#define PCIEMSITXR 0x000840
+#include "pcie-rcar.h"

-/* Transfer control */
-#define PCIETCTLR 0x02000
-#define DL_DOWN BIT(3)
-#define CFINIT BIT(0)
-#define PCIETSTR 0x02004
-#define DATA_LINK_ACTIVE BIT(0)
-#define PCIEERRFR 0x02020
-#define UNSUPPORTED_REQUEST BIT(4)
-#define PCIEMSIFR 0x02044
-#define PCIEMSIALR 0x02048
-#define MSIFE BIT(0)
-#define PCIEMSIAUR 0x0204c
-#define PCIEMSIIER 0x02050
-
-/* root port address */
-#define PCIEPRAR(x) (0x02080 + ((x) * 0x4))
-
-/* local address reg & mask */
-#define PCIELAR(x) (0x02200 + ((x) * 0x20))
-#define PCIELAMR(x) (0x02208 + ((x) * 0x20))
-#define LAM_PREFETCH BIT(3)
-#define LAM_64BIT BIT(2)
-#define LAR_ENABLE BIT(1)
-
-/* PCIe address reg & mask */
-#define PCIEPALR(x) (0x03400 + ((x) * 0x20))
-#define PCIEPAUR(x) (0x03404 + ((x) * 0x20))
-#define PCIEPAMR(x) (0x03408 + ((x) * 0x20))
-#define PCIEPTCTLR(x) (0x0340c + ((x) * 0x20))
-#define PAR_ENABLE BIT(31)
-#define IO_SPACE BIT(8)
-
-/* Configuration */
-#define PCICONF(x) (0x010000 + ((x) * 0x4))
-#define PMCAP(x) (0x010040 + ((x) * 0x4))
-#define EXPCAP(x) (0x010070 + ((x) * 0x4))
-#define VCCAP(x) (0x010100 + ((x) * 0x4))
-
-/* link layer */
-#define IDSETR1 0x011004
-#define TLCTLR 0x011048
-#define MACSR 0x011054
-#define SPCHGFIN BIT(4)
-#define SPCHGFAIL BIT(6)
-#define SPCHGSUC BIT(7)
-#define LINK_SPEED (0xf << 16)
-#define LINK_SPEED_2_5GTS (1 << 16)
-#define LINK_SPEED_5_0GTS (2 << 16)
-#define MACCTLR 0x011058
-#define MACCTLR_NFTS_MASK GENMASK(23, 16) /* The name is from SH7786 */
-#define SPEED_CHANGE BIT(24)
-#define SCRAMBLE_DISABLE BIT(27)
-#define LTSMDIS BIT(31)
-#define MACCTLR_INIT_VAL (LTSMDIS | MACCTLR_NFTS_MASK)
-#define PMSR 0x01105c
-#define MACS2R 0x011078
-#define MACCGSPSETR 0x011084
-#define SPCNGRSN BIT(31)
-
-/* R-Car H1 PHY */
-#define H1_PCIEPHYADRR 0x04000c
-#define WRITE_CMD BIT(16)
-#define PHY_ACK BIT(24)
-#define RATE_POS 12
-#define LANE_POS 8
-#define ADR_POS 0
-#define H1_PCIEPHYDOUTR 0x040014
-
-/* R-Car Gen2 PHY */
-#define GEN2_PCIEPHYADDR 0x780
-#define GEN2_PCIEPHYDATA 0x784
-#define GEN2_PCIEPHYCTRL 0x78c
-
-#define INT_PCI_MSI_NR 32
-
-#define RCONF(x) (PCICONF(0) + (x))
-#define RPMCAP(x) (PMCAP(0) + (x))
-#define REXPCAP(x) (EXPCAP(0) + (x))
-#define RVCCAP(x) (VCCAP(0) + (x))
-
-#define PCIE_CONF_BUS(b) (((b) & 0xff) << 24)
-#define PCIE_CONF_DEV(d) (((d) & 0x1f) << 19)
-#define PCIE_CONF_FUNC(f) (((f) & 0x7) << 16)
-
-#define RCAR_PCI_MAX_RESOURCES 4
-#define MAX_NR_INBOUND_MAPS 6
-
-struct rcar_msi {
- DECLARE_BITMAP(used, INT_PCI_MSI_NR);
- struct irq_domain *domain;
- struct msi_controller chip;
- unsigned long pages;
- struct mutex lock;
- int irq1;
- int irq2;
-};
-
-static inline struct rcar_msi *to_rcar_msi(struct msi_controller *chip)
+void rcar_pci_write_reg(void __iomem *base, u32 val, unsigned int reg)
{
- return container_of(chip, struct rcar_msi, chip);
+ writel(val, base + reg);
}

-/* Structure representing the PCIe interface */
-struct rcar_pcie {
- struct device *dev;
- struct phy *phy;
- void __iomem *base;
- struct list_head resources;
- int root_bus_nr;
- struct clk *bus_clk;
- struct rcar_msi msi;
-};
-
-static void rcar_pci_write_reg(struct rcar_pcie *pcie, u32 val,
- unsigned int reg)
+u32 rcar_pci_read_reg(void __iomem *base, unsigned int reg)
{
- writel(val, pcie->base + reg);
+ return readl(base + reg);
}

-static u32 rcar_pci_read_reg(struct rcar_pcie *pcie, unsigned int reg)
-{
- return readl(pcie->base + reg);
-}
-
-enum {
- RCAR_PCI_ACCESS_READ,
- RCAR_PCI_ACCESS_WRITE,
-};
-
-static void rcar_rmw32(struct rcar_pcie *pcie, int where, u32 mask, u32 data)
+void rcar_rmw32(void __iomem *base, int where, u32 mask, u32 data)
{
unsigned int shift = BITS_PER_BYTE * (where & 3);
- u32 val = rcar_pci_read_reg(pcie, where & ~3);
+ u32 val = rcar_pci_read_reg(base, where & ~3);

val &= ~(mask << shift);
val |= data << shift;
- rcar_pci_write_reg(pcie, val, where & ~3);
-}
-
-static u32 rcar_read_conf(struct rcar_pcie *pcie, int where)
-{
- unsigned int shift = BITS_PER_BYTE * (where & 3);
- u32 val = rcar_pci_read_reg(pcie, where & ~3);
-
- return val >> shift;
+ rcar_pci_write_reg(base, val, where & ~3);
}

-/* Serialization is provided by 'pci_lock' in drivers/pci/access.c */
-static int rcar_pcie_config_access(struct rcar_pcie *pcie,
- unsigned char access_type, struct pci_bus *bus,
- unsigned int devfn, int where, u32 *data)
+int rcar_pcie_wait_for_phyrdy(void __iomem *base)
{
- unsigned int dev, func, reg, index;
-
- dev = PCI_SLOT(devfn);
- func = PCI_FUNC(devfn);
- reg = where & ~3;
- index = reg / 4;
-
- /*
- * While each channel has its own memory-mapped extended config
- * space, it's generally only accessible when in endpoint mode.
- * When in root complex mode, the controller is unable to target
- * itself with either type 0 or type 1 accesses, and indeed, any
- * controller initiated target transfer to its own config space
- * result in a completer abort.
- *
- * Each channel effectively only supports a single device, but as
- * the same channel <-> device access works for any PCI_SLOT()
- * value, we cheat a bit here and bind the controller's config
- * space to devfn 0 in order to enable self-enumeration. In this
- * case the regular ECAR/ECDR path is sidelined and the mangled
- * config access itself is initiated as an internal bus transaction.
- */
- if (pci_is_root_bus(bus)) {
- if (dev != 0)
- return PCIBIOS_DEVICE_NOT_FOUND;
-
- if (access_type == RCAR_PCI_ACCESS_READ) {
- *data = rcar_pci_read_reg(pcie, PCICONF(index));
- } else {
- /* Keep an eye out for changes to the root bus number */
- if (pci_is_root_bus(bus) && (reg == PCI_PRIMARY_BUS))
- pcie->root_bus_nr = *data & 0xff;
-
- rcar_pci_write_reg(pcie, *data, PCICONF(index));
- }
-
- return PCIBIOS_SUCCESSFUL;
- }
-
- if (pcie->root_bus_nr < 0)
- return PCIBIOS_DEVICE_NOT_FOUND;
-
- /* Clear errors */
- rcar_pci_write_reg(pcie, rcar_pci_read_reg(pcie, PCIEERRFR), PCIEERRFR);
-
- /* Set the PIO address */
- rcar_pci_write_reg(pcie, PCIE_CONF_BUS(bus->number) |
- PCIE_CONF_DEV(dev) | PCIE_CONF_FUNC(func) | reg, PCIECAR);
-
- /* Enable the configuration access */
- if (bus->parent->number == pcie->root_bus_nr)
- rcar_pci_write_reg(pcie, CONFIG_SEND_ENABLE | TYPE0, PCIECCTLR);
- else
- rcar_pci_write_reg(pcie, CONFIG_SEND_ENABLE | TYPE1, PCIECCTLR);
-
- /* Check for errors */
- if (rcar_pci_read_reg(pcie, PCIEERRFR) & UNSUPPORTED_REQUEST)
- return PCIBIOS_DEVICE_NOT_FOUND;
-
- /* Check for master and target aborts */
- if (rcar_read_conf(pcie, RCONF(PCI_STATUS)) &
- (PCI_STATUS_REC_MASTER_ABORT | PCI_STATUS_REC_TARGET_ABORT))
- return PCIBIOS_DEVICE_NOT_FOUND;
-
- if (access_type == RCAR_PCI_ACCESS_READ)
- *data = rcar_pci_read_reg(pcie, PCIECDR);
- else
- rcar_pci_write_reg(pcie, *data, PCIECDR);
-
- /* Disable the configuration access */
- rcar_pci_write_reg(pcie, 0, PCIECCTLR);
-
- return PCIBIOS_SUCCESSFUL;
-}
+ unsigned int timeout = 10;

-static int rcar_pcie_read_conf(struct pci_bus *bus, unsigned int devfn,
- int where, int size, u32 *val)
-{
- struct rcar_pcie *pcie = bus->sysdata;
- int ret;
+ while (timeout--) {
+ if (rcar_pci_read_reg(base, PCIEPHYSR) & PHYRDY)
+ return 0;

- ret = rcar_pcie_config_access(pcie, RCAR_PCI_ACCESS_READ,
- bus, devfn, where, val);
- if (ret != PCIBIOS_SUCCESSFUL) {
- *val = 0xffffffff;
- return ret;
+ msleep(5);
}

- if (size == 1)
- *val = (*val >> (BITS_PER_BYTE * (where & 3))) & 0xff;
- else if (size == 2)
- *val = (*val >> (BITS_PER_BYTE * (where & 2))) & 0xffff;
-
- dev_dbg(&bus->dev, "pcie-config-read: bus=%3d devfn=0x%04x where=0x%04x size=%d val=0x%08x\n",
- bus->number, devfn, where, size, *val);
-
- return ret;
+ return -ETIMEDOUT;
}

-/* Serialization is provided by 'pci_lock' in drivers/pci/access.c */
-static int rcar_pcie_write_conf(struct pci_bus *bus, unsigned int devfn,
- int where, int size, u32 val)
+int rcar_pcie_wait_for_dl(void __iomem *base)
{
- struct rcar_pcie *pcie = bus->sysdata;
- unsigned int shift;
- u32 data;
- int ret;
-
- ret = rcar_pcie_config_access(pcie, RCAR_PCI_ACCESS_READ,
- bus, devfn, where, &data);
- if (ret != PCIBIOS_SUCCESSFUL)
- return ret;
-
- dev_dbg(&bus->dev, "pcie-config-write: bus=%3d devfn=0x%04x where=0x%04x size=%d val=0x%08x\n",
- bus->number, devfn, where, size, val);
+ unsigned int timeout = 10000;

- if (size == 1) {
- shift = BITS_PER_BYTE * (where & 3);
- data &= ~(0xff << shift);
- data |= ((val & 0xff) << shift);
- } else if (size == 2) {
- shift = BITS_PER_BYTE * (where & 2);
- data &= ~(0xffff << shift);
- data |= ((val & 0xffff) << shift);
- } else
- data = val;
+ while (timeout--) {
+ if ((rcar_pci_read_reg(base, PCIETSTR) & DATA_LINK_ACTIVE))
+ return 0;

- ret = rcar_pcie_config_access(pcie, RCAR_PCI_ACCESS_WRITE,
- bus, devfn, where, &data);
+ udelay(5);
+ cpu_relax();
+ }

- return ret;
+ return -ETIMEDOUT;
}

-static struct pci_ops rcar_pcie_ops = {
- .read = rcar_pcie_read_conf,
- .write = rcar_pcie_write_conf,
-};
-
-static void rcar_pcie_setup_window(int win, struct rcar_pcie *pcie,
- struct resource *res)
+void rcar_pcie_set_outbound(int win, void __iomem *base,
+ struct resource *res, bool host)
{
/* Setup PCIe address space mappings for each resource */
- resource_size_t size;
resource_size_t res_start;
+ resource_size_t size;
u32 mask;

- rcar_pci_write_reg(pcie, 0x00000000, PCIEPTCTLR(win));
+ rcar_pci_write_reg(base, 0x00000000, PCIEPTCTLR(win));

/*
* The PAMR mask is calculated in units of 128Bytes, which
@@ -348,15 +81,19 @@ static void rcar_pcie_setup_window(int win, struct rcar_pcie *pcie,
*/
size = resource_size(res);
mask = (roundup_pow_of_two(size) / SZ_128) - 1;
- rcar_pci_write_reg(pcie, mask << 7, PCIEPAMR(win));
+ rcar_pci_write_reg(base, mask << 7, PCIEPAMR(win));

- if (res->flags & IORESOURCE_IO)
- res_start = pci_pio_to_address(res->start);
- else
+ if (!host) {
res_start = res->start;
+ } else {
+ if (res->flags & IORESOURCE_IO)
+ res_start = pci_pio_to_address(res->start);
+ else
+ res_start = res->start;
+ }

- rcar_pci_write_reg(pcie, upper_32_bits(res_start), PCIEPAUR(win));
- rcar_pci_write_reg(pcie, lower_32_bits(res_start) & ~0x7F,
+ rcar_pci_write_reg(base, upper_32_bits(res_start), PCIEPAUR(win));
+ rcar_pci_write_reg(base, lower_32_bits(res_start) & ~0x7F,
PCIEPALR(win));

/* First resource is for IO */
@@ -364,886 +101,26 @@ static void rcar_pcie_setup_window(int win, struct rcar_pcie *pcie,
if (res->flags & IORESOURCE_IO)
mask |= IO_SPACE;

- rcar_pci_write_reg(pcie, mask, PCIEPTCTLR(win));
-}
-
-static int rcar_pcie_setup(struct list_head *resource, struct rcar_pcie *pci)
-{
- struct resource_entry *win;
- int i = 0;
-
- /* Setup PCI resources */
- resource_list_for_each_entry(win, &pci->resources) {
- struct resource *res = win->res;
-
- if (!res->flags)
- continue;
-
- switch (resource_type(res)) {
- case IORESOURCE_IO:
- case IORESOURCE_MEM:
- rcar_pcie_setup_window(i, pci, res);
- i++;
- break;
- case IORESOURCE_BUS:
- pci->root_bus_nr = res->start;
- break;
- default:
- continue;
- }
-
- pci_add_resource(resource, res);
- }
-
- return 1;
-}
-
-static void rcar_pcie_force_speedup(struct rcar_pcie *pcie)
-{
- struct device *dev = pcie->dev;
- unsigned int timeout = 1000;
- u32 macsr;
-
- if ((rcar_pci_read_reg(pcie, MACS2R) & LINK_SPEED) != LINK_SPEED_5_0GTS)
- return;
-
- if (rcar_pci_read_reg(pcie, MACCTLR) & SPEED_CHANGE) {
- dev_err(dev, "Speed change already in progress\n");
- return;
- }
-
- macsr = rcar_pci_read_reg(pcie, MACSR);
- if ((macsr & LINK_SPEED) == LINK_SPEED_5_0GTS)
- goto done;
-
- /* Set target link speed to 5.0 GT/s */
- rcar_rmw32(pcie, EXPCAP(12), PCI_EXP_LNKSTA_CLS,
- PCI_EXP_LNKSTA_CLS_5_0GB);
-
- /* Set speed change reason as intentional factor */
- rcar_rmw32(pcie, MACCGSPSETR, SPCNGRSN, 0);
-
- /* Clear SPCHGFIN, SPCHGSUC, and SPCHGFAIL */
- if (macsr & (SPCHGFIN | SPCHGSUC | SPCHGFAIL))
- rcar_pci_write_reg(pcie, macsr, MACSR);
-
- /* Start link speed change */
- rcar_rmw32(pcie, MACCTLR, SPEED_CHANGE, SPEED_CHANGE);
-
- while (timeout--) {
- macsr = rcar_pci_read_reg(pcie, MACSR);
- if (macsr & SPCHGFIN) {
- /* Clear the interrupt bits */
- rcar_pci_write_reg(pcie, macsr, MACSR);
-
- if (macsr & SPCHGFAIL)
- dev_err(dev, "Speed change failed\n");
-
- goto done;
- }
-
- msleep(1);
- }
-
- dev_err(dev, "Speed change timed out\n");
-
-done:
- dev_info(dev, "Current link speed is %s GT/s\n",
- (macsr & LINK_SPEED) == LINK_SPEED_5_0GTS ? "5" : "2.5");
-}
-
-static int rcar_pcie_enable(struct rcar_pcie *pcie)
-{
- struct device *dev = pcie->dev;
- struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
- struct pci_bus *bus, *child;
- int ret;
-
- /* Try setting 5 GT/s link speed */
- rcar_pcie_force_speedup(pcie);
-
- rcar_pcie_setup(&bridge->windows, pcie);
-
- pci_add_flags(PCI_REASSIGN_ALL_BUS);
-
- bridge->dev.parent = dev;
- bridge->sysdata = pcie;
- bridge->busnr = pcie->root_bus_nr;
- bridge->ops = &rcar_pcie_ops;
- bridge->map_irq = of_irq_parse_and_map_pci;
- bridge->swizzle_irq = pci_common_swizzle;
- if (IS_ENABLED(CONFIG_PCI_MSI))
- bridge->msi = &pcie->msi.chip;
-
- ret = pci_scan_root_bus_bridge(bridge);
- if (ret < 0)
- return ret;
-
- bus = bridge->bus;
-
- pci_bus_size_bridges(bus);
- pci_bus_assign_resources(bus);
-
- list_for_each_entry(child, &bus->children, node)
- pcie_bus_configure_settings(child);
-
- pci_bus_add_devices(bus);
-
- return 0;
-}
-
-static int phy_wait_for_ack(struct rcar_pcie *pcie)
-{
- struct device *dev = pcie->dev;
- unsigned int timeout = 100;
-
- while (timeout--) {
- if (rcar_pci_read_reg(pcie, H1_PCIEPHYADRR) & PHY_ACK)
- return 0;
-
- udelay(100);
- }
-
- dev_err(dev, "Access to PCIe phy timed out\n");
-
- return -ETIMEDOUT;
-}
-
-static void phy_write_reg(struct rcar_pcie *pcie,
- unsigned int rate, u32 addr,
- unsigned int lane, u32 data)
-{
- u32 phyaddr;
-
- phyaddr = WRITE_CMD |
- ((rate & 1) << RATE_POS) |
- ((lane & 0xf) << LANE_POS) |
- ((addr & 0xff) << ADR_POS);
-
- /* Set write data */
- rcar_pci_write_reg(pcie, data, H1_PCIEPHYDOUTR);
- rcar_pci_write_reg(pcie, phyaddr, H1_PCIEPHYADRR);
-
- /* Ignore errors as they will be dealt with if the data link is down */
- phy_wait_for_ack(pcie);
-
- /* Clear command */
- rcar_pci_write_reg(pcie, 0, H1_PCIEPHYDOUTR);
- rcar_pci_write_reg(pcie, 0, H1_PCIEPHYADRR);
-
- /* Ignore errors as they will be dealt with if the data link is down */
- phy_wait_for_ack(pcie);
-}
-
-static int rcar_pcie_wait_for_phyrdy(struct rcar_pcie *pcie)
-{
- unsigned int timeout = 10;
-
- while (timeout--) {
- if (rcar_pci_read_reg(pcie, PCIEPHYSR) & PHYRDY)
- return 0;
-
- msleep(5);
- }
-
- return -ETIMEDOUT;
-}
-
-static int rcar_pcie_wait_for_dl(struct rcar_pcie *pcie)
-{
- unsigned int timeout = 10000;
-
- while (timeout--) {
- if ((rcar_pci_read_reg(pcie, PCIETSTR) & DATA_LINK_ACTIVE))
- return 0;
-
- udelay(5);
- cpu_relax();
- }
-
- return -ETIMEDOUT;
-}
-
-static int rcar_pcie_hw_init(struct rcar_pcie *pcie)
-{
- int err;
-
- /* Begin initialization */
- rcar_pci_write_reg(pcie, 0, PCIETCTLR);
-
- /* Set mode */
- rcar_pci_write_reg(pcie, 1, PCIEMSR);
-
- err = rcar_pcie_wait_for_phyrdy(pcie);
- if (err)
- return err;
-
- /*
- * Initial header for port config space is type 1, set the device
- * class to match. Hardware takes care of propagating the IDSETR
- * settings, so there is no need to bother with a quirk.
- */
- rcar_pci_write_reg(pcie, PCI_CLASS_BRIDGE_PCI << 16, IDSETR1);
-
- /*
- * Setup Secondary Bus Number & Subordinate Bus Number, even though
- * they aren't used, to avoid bridge being detected as broken.
- */
- rcar_rmw32(pcie, RCONF(PCI_SECONDARY_BUS), 0xff, 1);
- rcar_rmw32(pcie, RCONF(PCI_SUBORDINATE_BUS), 0xff, 1);
-
- /* Initialize default capabilities. */
- rcar_rmw32(pcie, REXPCAP(0), 0xff, PCI_CAP_ID_EXP);
- rcar_rmw32(pcie, REXPCAP(PCI_EXP_FLAGS),
- PCI_EXP_FLAGS_TYPE, PCI_EXP_TYPE_ROOT_PORT << 4);
- rcar_rmw32(pcie, RCONF(PCI_HEADER_TYPE), 0x7f,
- PCI_HEADER_TYPE_BRIDGE);
-
- /* Enable data link layer active state reporting */
- rcar_rmw32(pcie, REXPCAP(PCI_EXP_LNKCAP), PCI_EXP_LNKCAP_DLLLARC,
- PCI_EXP_LNKCAP_DLLLARC);
-
- /* Write out the physical slot number = 0 */
- rcar_rmw32(pcie, REXPCAP(PCI_EXP_SLTCAP), PCI_EXP_SLTCAP_PSN, 0);
-
- /* Set the completion timer timeout to the maximum 50ms. */
- rcar_rmw32(pcie, TLCTLR + 1, 0x3f, 50);
-
- /* Terminate list of capabilities (Next Capability Offset=0) */
- rcar_rmw32(pcie, RVCCAP(0), 0xfff00000, 0);
-
- /* Enable MSI */
- if (IS_ENABLED(CONFIG_PCI_MSI))
- rcar_pci_write_reg(pcie, 0x801f0000, PCIEMSITXR);
-
- rcar_pci_write_reg(pcie, MACCTLR_INIT_VAL, MACCTLR);
-
- /* Finish initialization - establish a PCI Express link */
- rcar_pci_write_reg(pcie, CFINIT, PCIETCTLR);
-
- /* This will timeout if we don't have a link. */
- err = rcar_pcie_wait_for_dl(pcie);
- if (err)
- return err;
-
- /* Enable INTx interrupts */
- rcar_rmw32(pcie, PCIEINTXR, 0, 0xF << 8);
-
- wmb();
-
- return 0;
-}
-
-static int rcar_pcie_phy_init_h1(struct rcar_pcie *pcie)
-{
- /* Initialize the phy */
- phy_write_reg(pcie, 0, 0x42, 0x1, 0x0EC34191);
- phy_write_reg(pcie, 1, 0x42, 0x1, 0x0EC34180);
- phy_write_reg(pcie, 0, 0x43, 0x1, 0x00210188);
- phy_write_reg(pcie, 1, 0x43, 0x1, 0x00210188);
- phy_write_reg(pcie, 0, 0x44, 0x1, 0x015C0014);
- phy_write_reg(pcie, 1, 0x44, 0x1, 0x015C0014);
- phy_write_reg(pcie, 1, 0x4C, 0x1, 0x786174A0);
- phy_write_reg(pcie, 1, 0x4D, 0x1, 0x048000BB);
- phy_write_reg(pcie, 0, 0x51, 0x1, 0x079EC062);
- phy_write_reg(pcie, 0, 0x52, 0x1, 0x20000000);
- phy_write_reg(pcie, 1, 0x52, 0x1, 0x20000000);
- phy_write_reg(pcie, 1, 0x56, 0x1, 0x00003806);
-
- phy_write_reg(pcie, 0, 0x60, 0x1, 0x004B03A5);
- phy_write_reg(pcie, 0, 0x64, 0x1, 0x3F0F1F0F);
- phy_write_reg(pcie, 0, 0x66, 0x1, 0x00008000);
-
- return 0;
+ rcar_pci_write_reg(base, mask, PCIEPTCTLR(win));
}

-static int rcar_pcie_phy_init_gen2(struct rcar_pcie *pcie)
+void rcar_pcie_set_inbound(void __iomem *base,
+ u64 cpu_addr, u64 pci_addr,
+ u64 mask, int idx, bool host)
{
/*
- * These settings come from the R-Car Series, 2nd Generation User's
- * Manual, section 50.3.1 (2) Initialization of the physical layer.
+ * Set up 64-bit inbound regions as the range parser doesn't
+ * distinguish between 32 and 64-bit types.
*/
- rcar_pci_write_reg(pcie, 0x000f0030, GEN2_PCIEPHYADDR);
- rcar_pci_write_reg(pcie, 0x00381203, GEN2_PCIEPHYDATA);
- rcar_pci_write_reg(pcie, 0x00000001, GEN2_PCIEPHYCTRL);
- rcar_pci_write_reg(pcie, 0x00000006, GEN2_PCIEPHYCTRL);
-
- rcar_pci_write_reg(pcie, 0x000f0054, GEN2_PCIEPHYADDR);
- /* The following value is for DC connection, no termination resistor */
- rcar_pci_write_reg(pcie, 0x13802007, GEN2_PCIEPHYDATA);
- rcar_pci_write_reg(pcie, 0x00000001, GEN2_PCIEPHYCTRL);
- rcar_pci_write_reg(pcie, 0x00000006, GEN2_PCIEPHYCTRL);
-
- return 0;
-}
-
-static int rcar_pcie_phy_init_gen3(struct rcar_pcie *pcie)
-{
- int err;
-
- err = phy_init(pcie->phy);
- if (err)
- return err;
-
- err = phy_power_on(pcie->phy);
- if (err)
- phy_exit(pcie->phy);
-
- return err;
-}
-
-static int rcar_msi_alloc(struct rcar_msi *chip)
-{
- int msi;
-
- mutex_lock(&chip->lock);
-
- msi = find_first_zero_bit(chip->used, INT_PCI_MSI_NR);
- if (msi < INT_PCI_MSI_NR)
- set_bit(msi, chip->used);
- else
- msi = -ENOSPC;
-
- mutex_unlock(&chip->lock);
-
- return msi;
-}
-
-static int rcar_msi_alloc_region(struct rcar_msi *chip, int no_irqs)
-{
- int msi;
-
- mutex_lock(&chip->lock);
- msi = bitmap_find_free_region(chip->used, INT_PCI_MSI_NR,
- order_base_2(no_irqs));
- mutex_unlock(&chip->lock);
-
- return msi;
-}
-
-static void rcar_msi_free(struct rcar_msi *chip, unsigned long irq)
-{
- mutex_lock(&chip->lock);
- clear_bit(irq, chip->used);
- mutex_unlock(&chip->lock);
-}
-
-static irqreturn_t rcar_pcie_msi_irq(int irq, void *data)
-{
- struct rcar_pcie *pcie = data;
- struct rcar_msi *msi = &pcie->msi;
- struct device *dev = pcie->dev;
- unsigned long reg;
-
- reg = rcar_pci_read_reg(pcie, PCIEMSIFR);
-
- /* MSI & INTx share an interrupt - we only handle MSI here */
- if (!reg)
- return IRQ_NONE;
-
- while (reg) {
- unsigned int index = find_first_bit(&reg, 32);
- unsigned int msi_irq;
-
- /* clear the interrupt */
- rcar_pci_write_reg(pcie, 1 << index, PCIEMSIFR);
-
- msi_irq = irq_find_mapping(msi->domain, index);
- if (msi_irq) {
- if (test_bit(index, msi->used))
- generic_handle_irq(msi_irq);
- else
- dev_info(dev, "unhandled MSI\n");
- } else {
- /* Unknown MSI, just clear it */
- dev_dbg(dev, "unexpected MSI\n");
- }
-
- /* see if there's any more pending in this vector */
- reg = rcar_pci_read_reg(pcie, PCIEMSIFR);
- }
-
- return IRQ_HANDLED;
-}
-
-static int rcar_msi_setup_irq(struct msi_controller *chip, struct pci_dev *pdev,
- struct msi_desc *desc)
-{
- struct rcar_msi *msi = to_rcar_msi(chip);
- struct rcar_pcie *pcie = container_of(chip, struct rcar_pcie, msi.chip);
- struct msi_msg msg;
- unsigned int irq;
- int hwirq;
-
- hwirq = rcar_msi_alloc(msi);
- if (hwirq < 0)
- return hwirq;
-
- irq = irq_find_mapping(msi->domain, hwirq);
- if (!irq) {
- rcar_msi_free(msi, hwirq);
- return -EINVAL;
- }
-
- irq_set_msi_desc(irq, desc);
-
- msg.address_lo = rcar_pci_read_reg(pcie, PCIEMSIALR) & ~MSIFE;
- msg.address_hi = rcar_pci_read_reg(pcie, PCIEMSIAUR);
- msg.data = hwirq;
-
- pci_write_msi_msg(irq, &msg);
-
- return 0;
-}
-
-static int rcar_msi_setup_irqs(struct msi_controller *chip,
- struct pci_dev *pdev, int nvec, int type)
-{
- struct rcar_pcie *pcie = container_of(chip, struct rcar_pcie, msi.chip);
- struct rcar_msi *msi = to_rcar_msi(chip);
- struct msi_desc *desc;
- struct msi_msg msg;
- unsigned int irq;
- int hwirq;
- int i;
-
- /* MSI-X interrupts are not supported */
- if (type == PCI_CAP_ID_MSIX)
- return -EINVAL;
-
- WARN_ON(!list_is_singular(&pdev->dev.msi_list));
- desc = list_entry(pdev->dev.msi_list.next, struct msi_desc, list);
-
- hwirq = rcar_msi_alloc_region(msi, nvec);
- if (hwirq < 0)
- return -ENOSPC;
-
- irq = irq_find_mapping(msi->domain, hwirq);
- if (!irq)
- return -ENOSPC;
-
- for (i = 0; i < nvec; i++) {
- /*
- * irq_create_mapping() called from rcar_pcie_probe() pre-
- * allocates descs, so there is no need to allocate descs here.
- * We can therefore assume that if irq_find_mapping() above
- * returns non-zero, then the descs are also successfully
- * allocated.
- */
- if (irq_set_msi_desc_off(irq, i, desc)) {
- /* TODO: clear */
- return -EINVAL;
- }
- }
-
- desc->nvec_used = nvec;
- desc->msi_attrib.multiple = order_base_2(nvec);
-
- msg.address_lo = rcar_pci_read_reg(pcie, PCIEMSIALR) & ~MSIFE;
- msg.address_hi = rcar_pci_read_reg(pcie, PCIEMSIAUR);
- msg.data = hwirq;
-
- pci_write_msi_msg(irq, &msg);
-
- return 0;
-}
-
-static void rcar_msi_teardown_irq(struct msi_controller *chip, unsigned int irq)
-{
- struct rcar_msi *msi = to_rcar_msi(chip);
- struct irq_data *d = irq_get_irq_data(irq);
-
- rcar_msi_free(msi, d->hwirq);
-}
-
-static struct irq_chip rcar_msi_irq_chip = {
- .name = "R-Car PCIe MSI",
- .irq_enable = pci_msi_unmask_irq,
- .irq_disable = pci_msi_mask_irq,
- .irq_mask = pci_msi_mask_irq,
- .irq_unmask = pci_msi_unmask_irq,
-};
-
-static int rcar_msi_map(struct irq_domain *domain, unsigned int irq,
- irq_hw_number_t hwirq)
-{
- irq_set_chip_and_handler(irq, &rcar_msi_irq_chip, handle_simple_irq);
- irq_set_chip_data(irq, domain->host_data);
-
- return 0;
-}
-
-static const struct irq_domain_ops msi_domain_ops = {
- .map = rcar_msi_map,
-};
-
-static void rcar_pcie_unmap_msi(struct rcar_pcie *pcie)
-{
- struct rcar_msi *msi = &pcie->msi;
- int i, irq;
-
- for (i = 0; i < INT_PCI_MSI_NR; i++) {
- irq = irq_find_mapping(msi->domain, i);
- if (irq > 0)
- irq_dispose_mapping(irq);
- }
-
- irq_domain_remove(msi->domain);
-}
-
-static int rcar_pcie_enable_msi(struct rcar_pcie *pcie)
-{
- struct device *dev = pcie->dev;
- struct rcar_msi *msi = &pcie->msi;
- phys_addr_t base;
- int err, i;
-
- mutex_init(&msi->lock);
-
- msi->chip.dev = dev;
- msi->chip.setup_irq = rcar_msi_setup_irq;
- msi->chip.setup_irqs = rcar_msi_setup_irqs;
- msi->chip.teardown_irq = rcar_msi_teardown_irq;
-
- msi->domain = irq_domain_add_linear(dev->of_node, INT_PCI_MSI_NR,
- &msi_domain_ops, &msi->chip);
- if (!msi->domain) {
- dev_err(dev, "failed to create IRQ domain\n");
- return -ENOMEM;
- }
-
- for (i = 0; i < INT_PCI_MSI_NR; i++)
- irq_create_mapping(msi->domain, i);
-
- /* Two irqs are for MSI, but they are also used for non-MSI irqs */
- err = devm_request_irq(dev, msi->irq1, rcar_pcie_msi_irq,
- IRQF_SHARED | IRQF_NO_THREAD,
- rcar_msi_irq_chip.name, pcie);
- if (err < 0) {
- dev_err(dev, "failed to request IRQ: %d\n", err);
- goto err;
- }
-
- err = devm_request_irq(dev, msi->irq2, rcar_pcie_msi_irq,
- IRQF_SHARED | IRQF_NO_THREAD,
- rcar_msi_irq_chip.name, pcie);
- if (err < 0) {
- dev_err(dev, "failed to request IRQ: %d\n", err);
- goto err;
- }
-
- /* setup MSI data target */
- msi->pages = __get_free_pages(GFP_KERNEL, 0);
- if (!msi->pages) {
- err = -ENOMEM;
- goto err;
- }
- base = virt_to_phys((void *)msi->pages);
-
- rcar_pci_write_reg(pcie, lower_32_bits(base) | MSIFE, PCIEMSIALR);
- rcar_pci_write_reg(pcie, upper_32_bits(base), PCIEMSIAUR);
-
- /* enable all MSI interrupts */
- rcar_pci_write_reg(pcie, 0xffffffff, PCIEMSIIER);
-
- return 0;
-
-err:
- rcar_pcie_unmap_msi(pcie);
- return err;
-}
-
-static void rcar_pcie_teardown_msi(struct rcar_pcie *pcie)
-{
- struct rcar_msi *msi = &pcie->msi;
-
- /* Disable all MSI interrupts */
- rcar_pci_write_reg(pcie, 0, PCIEMSIIER);
-
- /* Disable address decoding of the MSI interrupt, MSIFE */
- rcar_pci_write_reg(pcie, 0, PCIEMSIALR);
-
- free_pages(msi->pages, 0);
-
- rcar_pcie_unmap_msi(pcie);
-}
-
-static int rcar_pcie_get_resources(struct rcar_pcie *pcie)
-{
- struct device *dev = pcie->dev;
- struct resource res;
- int err, i;
-
- pcie->phy = devm_phy_optional_get(dev, "pcie");
- if (IS_ERR(pcie->phy))
- return PTR_ERR(pcie->phy);
-
- err = of_address_to_resource(dev->of_node, 0, &res);
- if (err)
- return err;
-
- pcie->base = devm_ioremap_resource(dev, &res);
- if (IS_ERR(pcie->base))
- return PTR_ERR(pcie->base);
-
- pcie->bus_clk = devm_clk_get(dev, "pcie_bus");
- if (IS_ERR(pcie->bus_clk)) {
- dev_err(dev, "cannot get pcie bus clock\n");
- return PTR_ERR(pcie->bus_clk);
- }
-
- i = irq_of_parse_and_map(dev->of_node, 0);
- if (!i) {
- dev_err(dev, "cannot get platform resources for msi interrupt\n");
- err = -ENOENT;
- goto err_irq1;
- }
- pcie->msi.irq1 = i;
-
- i = irq_of_parse_and_map(dev->of_node, 1);
- if (!i) {
- dev_err(dev, "cannot get platform resources for msi interrupt\n");
- err = -ENOENT;
- goto err_irq2;
- }
- pcie->msi.irq2 = i;
-
- return 0;
-
-err_irq2:
- irq_dispose_mapping(pcie->msi.irq1);
-err_irq1:
- return err;
-}
-
-static int rcar_pcie_inbound_ranges(struct rcar_pcie *pcie,
- struct resource_entry *entry,
- int *index)
-{
- u64 restype = entry->res->flags;
- u64 cpu_addr = entry->res->start;
- u64 cpu_end = entry->res->end;
- u64 pci_addr = entry->res->start - entry->offset;
- u32 flags = LAM_64BIT | LAR_ENABLE;
- u64 mask;
- u64 size = resource_size(entry->res);
- int idx = *index;
-
- if (restype & IORESOURCE_PREFETCH)
- flags |= LAM_PREFETCH;
-
- while (cpu_addr < cpu_end) {
- if (idx >= MAX_NR_INBOUND_MAPS - 1) {
- dev_err(pcie->dev, "Failed to map inbound regions!\n");
- return -EINVAL;
- }
- /*
- * If the size of the range is larger than the alignment of
- * the start address, we have to use multiple entries to
- * perform the mapping.
- */
- if (cpu_addr > 0) {
- unsigned long nr_zeros = __ffs64(cpu_addr);
- u64 alignment = 1ULL << nr_zeros;
-
- size = min(size, alignment);
- }
- /* Hardware supports max 4GiB inbound region */
- size = min(size, 1ULL << 32);
-
- mask = roundup_pow_of_two(size) - 1;
- mask &= ~0xf;
-
- /*
- * Set up 64-bit inbound regions as the range parser doesn't
- * distinguish between 32 and 64-bit types.
- */
- rcar_pci_write_reg(pcie, lower_32_bits(pci_addr),
+ if (host)
+ rcar_pci_write_reg(base, lower_32_bits(pci_addr),
PCIEPRAR(idx));
- rcar_pci_write_reg(pcie, lower_32_bits(cpu_addr), PCIELAR(idx));
- rcar_pci_write_reg(pcie, lower_32_bits(mask) | flags,
- PCIELAMR(idx));
+ rcar_pci_write_reg(base, lower_32_bits(cpu_addr), PCIELAR(idx));
+ rcar_pci_write_reg(base, lower_32_bits(mask), PCIELAMR(idx));

- rcar_pci_write_reg(pcie, upper_32_bits(pci_addr),
+ if (host)
+ rcar_pci_write_reg(base, upper_32_bits(pci_addr),
PCIEPRAR(idx + 1));
- rcar_pci_write_reg(pcie, upper_32_bits(cpu_addr),
- PCIELAR(idx + 1));
- rcar_pci_write_reg(pcie, 0, PCIELAMR(idx + 1));
-
- pci_addr += size;
- cpu_addr += size;
- idx += 2;
- }
- *index = idx;
-
- return 0;
-}
-
-static int rcar_pcie_parse_map_dma_ranges(struct rcar_pcie *pcie)
-{
- struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
- struct resource_entry *entry;
- int index = 0, err = 0;
-
- resource_list_for_each_entry(entry, &bridge->dma_ranges) {
- err = rcar_pcie_inbound_ranges(pcie, entry, &index);
- if (err)
- break;
- }
-
- return err;
+ rcar_pci_write_reg(base, upper_32_bits(cpu_addr), PCIELAR(idx + 1));
+ rcar_pci_write_reg(base, 0, PCIELAMR(idx + 1));
}
-
-static const struct of_device_id rcar_pcie_of_match[] = {
- { .compatible = "renesas,pcie-r8a7779",
- .data = rcar_pcie_phy_init_h1 },
- { .compatible = "renesas,pcie-r8a7790",
- .data = rcar_pcie_phy_init_gen2 },
- { .compatible = "renesas,pcie-r8a7791",
- .data = rcar_pcie_phy_init_gen2 },
- { .compatible = "renesas,pcie-rcar-gen2",
- .data = rcar_pcie_phy_init_gen2 },
- { .compatible = "renesas,pcie-r8a7795",
- .data = rcar_pcie_phy_init_gen3 },
- { .compatible = "renesas,pcie-rcar-gen3",
- .data = rcar_pcie_phy_init_gen3 },
- {},
-};
-
-static int rcar_pcie_probe(struct platform_device *pdev)
-{
- struct device *dev = &pdev->dev;
- struct rcar_pcie *pcie;
- u32 data;
- int err;
- int (*phy_init_fn)(struct rcar_pcie *);
- struct pci_host_bridge *bridge;
-
- bridge = pci_alloc_host_bridge(sizeof(*pcie));
- if (!bridge)
- return -ENOMEM;
-
- pcie = pci_host_bridge_priv(bridge);
-
- pcie->dev = dev;
- platform_set_drvdata(pdev, pcie);
-
- err = pci_parse_request_of_pci_ranges(dev, &pcie->resources,
- &bridge->dma_ranges, NULL);
- if (err)
- goto err_free_bridge;
-
- pm_runtime_enable(pcie->dev);
- err = pm_runtime_get_sync(pcie->dev);
- if (err < 0) {
- dev_err(pcie->dev, "pm_runtime_get_sync failed\n");
- goto err_pm_disable;
- }
-
- err = rcar_pcie_get_resources(pcie);
- if (err < 0) {
- dev_err(dev, "failed to request resources: %d\n", err);
- goto err_pm_put;
- }
-
- err = clk_prepare_enable(pcie->bus_clk);
- if (err) {
- dev_err(dev, "failed to enable bus clock: %d\n", err);
- goto err_unmap_msi_irqs;
- }
-
- err = rcar_pcie_parse_map_dma_ranges(pcie);
- if (err)
- goto err_clk_disable;
-
- phy_init_fn = of_device_get_match_data(dev);
- err = phy_init_fn(pcie);
- if (err) {
- dev_err(dev, "failed to init PCIe PHY\n");
- goto err_clk_disable;
- }
-
- /* Failure to get a link might just be that no cards are inserted */
- if (rcar_pcie_hw_init(pcie)) {
- dev_info(dev, "PCIe link down\n");
- err = -ENODEV;
- goto err_phy_shutdown;
- }
-
- data = rcar_pci_read_reg(pcie, MACSR);
- dev_info(dev, "PCIe x%d: link up\n", (data >> 20) & 0x3f);
-
- if (IS_ENABLED(CONFIG_PCI_MSI)) {
- err = rcar_pcie_enable_msi(pcie);
- if (err < 0) {
- dev_err(dev,
- "failed to enable MSI support: %d\n",
- err);
- goto err_phy_shutdown;
- }
- }
-
- err = rcar_pcie_enable(pcie);
- if (err)
- goto err_msi_teardown;
-
- return 0;
-
-err_msi_teardown:
- if (IS_ENABLED(CONFIG_PCI_MSI))
- rcar_pcie_teardown_msi(pcie);
-
-err_phy_shutdown:
- if (pcie->phy) {
- phy_power_off(pcie->phy);
- phy_exit(pcie->phy);
- }
-
-err_clk_disable:
- clk_disable_unprepare(pcie->bus_clk);
-
-err_unmap_msi_irqs:
- irq_dispose_mapping(pcie->msi.irq2);
- irq_dispose_mapping(pcie->msi.irq1);
-
-err_pm_put:
- pm_runtime_put(dev);
-
-err_pm_disable:
- pm_runtime_disable(dev);
- pci_free_resource_list(&pcie->resources);
-
-err_free_bridge:
- pci_free_host_bridge(bridge);
-
- return err;
-}
-
-static int rcar_pcie_resume_noirq(struct device *dev)
-{
- struct rcar_pcie *pcie = dev_get_drvdata(dev);
-
- if (rcar_pci_read_reg(pcie, PMSR) &&
- !(rcar_pci_read_reg(pcie, PCIETCTLR) & DL_DOWN))
- return 0;
-
- /* Re-establish the PCIe link */
- rcar_pci_write_reg(pcie, MACCTLR_INIT_VAL, MACCTLR);
- rcar_pci_write_reg(pcie, CFINIT, PCIETCTLR);
- return rcar_pcie_wait_for_dl(pcie);
-}
-
-static const struct dev_pm_ops rcar_pcie_pm_ops = {
- .resume_noirq = rcar_pcie_resume_noirq,
-};
-
-static struct platform_driver rcar_pcie_driver = {
- .driver = {
- .name = "rcar-pcie",
- .of_match_table = rcar_pcie_of_match,
- .pm = &rcar_pcie_pm_ops,
- .suppress_bind_attrs = true,
- },
- .probe = rcar_pcie_probe,
-};
-builtin_platform_driver(rcar_pcie_driver);
diff --git a/drivers/pci/controller/pcie-rcar.h b/drivers/pci/controller/pcie-rcar.h
new file mode 100644
index 000000000000..cbb21d37b539
--- /dev/null
+++ b/drivers/pci/controller/pcie-rcar.h
@@ -0,0 +1,126 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * PCIe driver for Renesas R-Car SoCs
+ * Copyright (C) 2014-2020 Renesas Electronics Europe Ltd
+ *
+ * Author: Phil Edworthy <[email protected]>
+ */
+
+#ifndef _PCIE_RCAR_H
+#define _PCIE_RCAR_H
+
+#define PCIECAR 0x000010
+#define PCIECCTLR 0x000018
+#define CONFIG_SEND_ENABLE BIT(31)
+#define TYPE0 (0 << 8)
+#define TYPE1 BIT(8)
+#define PCIECDR 0x000020
+#define PCIEMSR 0x000028
+#define PCIEINTXR 0x000400
+#define PCIEPHYSR 0x0007f0
+#define PHYRDY BIT(0)
+#define PCIEMSITXR 0x000840
+
+/* Transfer control */
+#define PCIETCTLR 0x02000
+#define DL_DOWN BIT(3)
+#define CFINIT BIT(0)
+#define PCIETSTR 0x02004
+#define DATA_LINK_ACTIVE BIT(0)
+#define PCIEERRFR 0x02020
+#define UNSUPPORTED_REQUEST BIT(4)
+#define PCIEMSIFR 0x02044
+#define PCIEMSIALR 0x02048
+#define MSIFE BIT(0)
+#define PCIEMSIAUR 0x0204c
+#define PCIEMSIIER 0x02050
+
+/* root port address */
+#define PCIEPRAR(x) (0x02080 + ((x) * 0x4))
+
+/* local address reg & mask */
+#define PCIELAR(x) (0x02200 + ((x) * 0x20))
+#define PCIELAMR(x) (0x02208 + ((x) * 0x20))
+#define LAM_PREFETCH BIT(3)
+#define LAM_64BIT BIT(2)
+#define LAR_ENABLE BIT(1)
+
+/* PCIe address reg & mask */
+#define PCIEPALR(x) (0x03400 + ((x) * 0x20))
+#define PCIEPAUR(x) (0x03404 + ((x) * 0x20))
+#define PCIEPAMR(x) (0x03408 + ((x) * 0x20))
+#define PCIEPTCTLR(x) (0x0340c + ((x) * 0x20))
+#define PAR_ENABLE BIT(31)
+#define IO_SPACE BIT(8)
+
+/* Configuration */
+#define PCICONF(x) (0x010000 + ((x) * 0x4))
+#define PMCAP(x) (0x010040 + ((x) * 0x4))
+#define EXPCAP(x) (0x010070 + ((x) * 0x4))
+#define VCCAP(x) (0x010100 + ((x) * 0x4))
+
+/* link layer */
+#define IDSETR1 0x011004
+#define TLCTLR 0x011048
+#define MACSR 0x011054
+#define SPCHGFIN BIT(4)
+#define SPCHGFAIL BIT(6)
+#define SPCHGSUC BIT(7)
+#define LINK_SPEED (0xf << 16)
+#define LINK_SPEED_2_5GTS (1 << 16)
+#define LINK_SPEED_5_0GTS (2 << 16)
+#define MACCTLR 0x011058
+#define MACCTLR_NFTS_MASK GENMASK(23, 16) /* The name is from SH7786 */
+#define SPEED_CHANGE BIT(24)
+#define SCRAMBLE_DISABLE BIT(27)
+#define LTSMDIS BIT(31)
+#define MACCTLR_INIT_VAL (LTSMDIS | MACCTLR_NFTS_MASK)
+#define PMSR 0x01105c
+#define MACS2R 0x011078
+#define MACCGSPSETR 0x011084
+#define SPCNGRSN BIT(31)
+
+/* R-Car H1 PHY */
+#define H1_PCIEPHYADRR 0x04000c
+#define WRITE_CMD BIT(16)
+#define PHY_ACK BIT(24)
+#define RATE_POS 12
+#define LANE_POS 8
+#define ADR_POS 0
+#define H1_PCIEPHYDOUTR 0x040014
+
+/* R-Car Gen2 PHY */
+#define GEN2_PCIEPHYADDR 0x780
+#define GEN2_PCIEPHYDATA 0x784
+#define GEN2_PCIEPHYCTRL 0x78c
+
+#define INT_PCI_MSI_NR 32
+
+#define RCONF(x) (PCICONF(0) + (x))
+#define RPMCAP(x) (PMCAP(0) + (x))
+#define REXPCAP(x) (EXPCAP(0) + (x))
+#define RVCCAP(x) (VCCAP(0) + (x))
+
+#define PCIE_CONF_BUS(b) (((b) & 0xff) << 24)
+#define PCIE_CONF_DEV(d) (((d) & 0x1f) << 19)
+#define PCIE_CONF_FUNC(f) (((f) & 0x7) << 16)
+
+#define RCAR_PCI_MAX_RESOURCES 4
+#define MAX_NR_INBOUND_MAPS 6
+
+enum {
+ RCAR_PCI_ACCESS_READ,
+ RCAR_PCI_ACCESS_WRITE,
+};
+
+void rcar_pci_write_reg(void __iomem *base, u32 val, unsigned int reg);
+u32 rcar_pci_read_reg(void __iomem *base, unsigned int reg);
+void rcar_rmw32(void __iomem *base, int where, u32 mask, u32 data);
+int rcar_pcie_wait_for_phyrdy(void __iomem *base);
+int rcar_pcie_wait_for_dl(void __iomem *base);
+void rcar_pcie_set_outbound(int win, void __iomem *base,
+ struct resource *res, bool host);
+void rcar_pcie_set_inbound(void __iomem *base, u64 cpu_addr, u64 pci_addr,
+ u64 mask, int idx, bool host);
+
+#endif
--
2.20.1

2020-01-13 21:26:34

by Rob Herring (Arm)

[permalink] [raw]
Subject: Re: [v3 4/6] dt-bindings: PCI: rcar: Add bindings for R-Car PCIe endpoint controller

On Wed, Jan 08, 2020 at 04:22:09PM +0000, Lad Prabhakar wrote:
> This patch adds the bindings for the R-Car PCIe endpoint driver.
>
> Signed-off-by: Lad Prabhakar <[email protected]>
> ---
> .../devicetree/bindings/pci/rcar-pci-ep.yaml | 76 +++++++++++++++++++
> 1 file changed, 76 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml

Fails 'make dt_binding_check':

Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml: $id:
path/filename 'pci/rcar-pcie-ep.yaml' doesn't match actual filename

>
> diff --git a/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml b/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
> new file mode 100644
> index 000000000000..99c2a1174463
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
> @@ -0,0 +1,76 @@
> +# SPDX-License-Identifier: GPL-2.0
> +# Copyright (C) 2020 Renesas Electronics Europe GmbH - https://www.renesas.com/eu/en/
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pci/rcar-pcie-ep.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Renesas R-Car PCIe Endpoint
> +
> +maintainers:
> + - Lad Prabhakar <[email protected]>
> +
> +properties:
> + compatible:
> + items:
> + - const: renesas,r8a774c0-pcie-ep
> + - const: renesas,rcar-gen3-pcie-ep
> +
> + reg:
> + maxItems: 5
> +
> + reg-names:
> + items:
> + - const: apb-base
> + - const: memory0
> + - const: memory1
> + - const: memory2
> + - const: memory3
> +
> + power-domains:
> + maxItems: 1
> +
> + resets:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 1
> +
> + clock-names:
> + items:
> + - const: pcie
> +
> + max-functions:
> + minimum: 1
> + maximum: 6
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - resets
> + - power-domains
> + - clocks
> + - clock-names
> + - max-functions
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/r8a774c0-cpg-mssr.h>
> + #include <dt-bindings/power/r8a774c0-sysc.h>
> +
> + pcie0_ep: pcie-ep@fe000000 {
> + compatible = "renesas,r8a774c0-pcie-ep",
> + "renesas,rcar-gen3-pcie-ep";
> + reg = <0 0xfe000000 0 0x80000>,
> + <0x0 0xfe100000 0 0x100000>,
> + <0x0 0xfe200000 0 0x200000>,
> + <0x0 0x30000000 0 0x8000000>,
> + <0x0 0x38000000 0 0x8000000>;
> + reg-names = "apb-base", "memory0", "memory1", "memory2", "memory3";
> + resets = <&cpg 319>;
> + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>;
> + clocks = <&cpg CPG_MOD 319>;
> + clock-names = "pcie";
> + max-functions = /bits/ 8 <1>;
> + };
> --
> 2.20.1
>

2020-01-14 08:13:10

by Lad, Prabhakar

[permalink] [raw]
Subject: Re: [v3 4/6] dt-bindings: PCI: rcar: Add bindings for R-Car PCIe endpoint controller

Hi Rob,

thank you for the review.

On Mon, Jan 13, 2020 at 9:23 PM Rob Herring <[email protected]> wrote:
>
> On Wed, Jan 08, 2020 at 04:22:09PM +0000, Lad Prabhakar wrote:
> > This patch adds the bindings for the R-Car PCIe endpoint driver.
> >
> > Signed-off-by: Lad Prabhakar <[email protected]>
> > ---
> > .../devicetree/bindings/pci/rcar-pci-ep.yaml | 76 +++++++++++++++++++
> > 1 file changed, 76 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
>
> Fails 'make dt_binding_check':
>
> Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml: $id:
> path/filename 'pci/rcar-pcie-ep.yaml' doesn't match actual filename
>
my bad fill that and post a v4.

Cheers,
--Prabhakar Lad
> >
> > diff --git a/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml b/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
> > new file mode 100644
> > index 000000000000..99c2a1174463
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
> > @@ -0,0 +1,76 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +# Copyright (C) 2020 Renesas Electronics Europe GmbH - https://www.renesas.com/eu/en/
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/pci/rcar-pcie-ep.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Renesas R-Car PCIe Endpoint
> > +
> > +maintainers:
> > + - Lad Prabhakar <[email protected]>
> > +
> > +properties:
> > + compatible:
> > + items:
> > + - const: renesas,r8a774c0-pcie-ep
> > + - const: renesas,rcar-gen3-pcie-ep
> > +
> > + reg:
> > + maxItems: 5
> > +
> > + reg-names:
> > + items:
> > + - const: apb-base
> > + - const: memory0
> > + - const: memory1
> > + - const: memory2
> > + - const: memory3
> > +
> > + power-domains:
> > + maxItems: 1
> > +
> > + resets:
> > + maxItems: 1
> > +
> > + clocks:
> > + maxItems: 1
> > +
> > + clock-names:
> > + items:
> > + - const: pcie
> > +
> > + max-functions:
> > + minimum: 1
> > + maximum: 6
> > +
> > +required:
> > + - compatible
> > + - reg
> > + - reg-names
> > + - resets
> > + - power-domains
> > + - clocks
> > + - clock-names
> > + - max-functions
> > +
> > +examples:
> > + - |
> > + #include <dt-bindings/clock/r8a774c0-cpg-mssr.h>
> > + #include <dt-bindings/power/r8a774c0-sysc.h>
> > +
> > + pcie0_ep: pcie-ep@fe000000 {
> > + compatible = "renesas,r8a774c0-pcie-ep",
> > + "renesas,rcar-gen3-pcie-ep";
> > + reg = <0 0xfe000000 0 0x80000>,
> > + <0x0 0xfe100000 0 0x100000>,
> > + <0x0 0xfe200000 0 0x200000>,
> > + <0x0 0x30000000 0 0x8000000>,
> > + <0x0 0x38000000 0 0x8000000>;
> > + reg-names = "apb-base", "memory0", "memory1", "memory2", "memory3";
> > + resets = <&cpg 319>;
> > + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>;
> > + clocks = <&cpg CPG_MOD 319>;
> > + clock-names = "pcie";
> > + max-functions = /bits/ 8 <1>;
> > + };
> > --
> > 2.20.1
> >
>
> _______________________________________________
> linux-arm-kernel mailing list
> [email protected]
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

2020-01-21 17:58:48

by Lad, Prabhakar

[permalink] [raw]
Subject: Re: [v3 4/6] dt-bindings: PCI: rcar: Add bindings for R-Car PCIe endpoint controller

Hi Rob/Kishon,

On Wed, Jan 8, 2020 at 4:22 PM Lad Prabhakar <[email protected]> wrote:
>
> This patch adds the bindings for the R-Car PCIe endpoint driver.
>
> Signed-off-by: Lad Prabhakar <[email protected]>
> ---
> .../devicetree/bindings/pci/rcar-pci-ep.yaml | 76 +++++++++++++++++++
> 1 file changed, 76 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
>
> diff --git a/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml b/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
> new file mode 100644
> index 000000000000..99c2a1174463
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
> @@ -0,0 +1,76 @@
> +# SPDX-License-Identifier: GPL-2.0
> +# Copyright (C) 2020 Renesas Electronics Europe GmbH - https://www.renesas.com/eu/en/
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pci/rcar-pcie-ep.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Renesas R-Car PCIe Endpoint
> +
> +maintainers:
> + - Lad Prabhakar <[email protected]>
> +
> +properties:
> + compatible:
> + items:
> + - const: renesas,r8a774c0-pcie-ep
> + - const: renesas,rcar-gen3-pcie-ep
> +
> + reg:
> + maxItems: 5
> +
> + reg-names:
> + items:
> + - const: apb-base
> + - const: memory0
> + - const: memory1
> + - const: memory2
> + - const: memory3
> +
> + power-domains:
> + maxItems: 1
> +
> + resets:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 1
> +
> + clock-names:
> + items:
> + - const: pcie
> +
> + max-functions:
> + minimum: 1
> + maximum: 6
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - resets
> + - power-domains
> + - clocks
> + - clock-names
> + - max-functions
> +
apart from dt_binding_check error are we OK with dt bindings ?

Cheers,
--Prabhakar

> +examples:
> + - |
> + #include <dt-bindings/clock/r8a774c0-cpg-mssr.h>
> + #include <dt-bindings/power/r8a774c0-sysc.h>
> +
> + pcie0_ep: pcie-ep@fe000000 {
> + compatible = "renesas,r8a774c0-pcie-ep",
> + "renesas,rcar-gen3-pcie-ep";
> + reg = <0 0xfe000000 0 0x80000>,
> + <0x0 0xfe100000 0 0x100000>,
> + <0x0 0xfe200000 0 0x200000>,
> + <0x0 0x30000000 0 0x8000000>,
> + <0x0 0x38000000 0 0x8000000>;
> + reg-names = "apb-base", "memory0", "memory1", "memory2", "memory3";
> + resets = <&cpg 319>;
> + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>;
> + clocks = <&cpg CPG_MOD 319>;
> + clock-names = "pcie";
> + max-functions = /bits/ 8 <1>;
> + };
> --
> 2.20.1
>

2020-01-22 08:14:43

by Kishon Vijay Abraham I

[permalink] [raw]
Subject: Re: [v3 4/6] dt-bindings: PCI: rcar: Add bindings for R-Car PCIe endpoint controller

Hi Prabhakar,

On 21/01/20 11:27 PM, Lad, Prabhakar wrote:
> Hi Rob/Kishon,
>
> On Wed, Jan 8, 2020 at 4:22 PM Lad Prabhakar <[email protected]> wrote:
>>
>> This patch adds the bindings for the R-Car PCIe endpoint driver.
>>
>> Signed-off-by: Lad Prabhakar <[email protected]>
>> ---
>> .../devicetree/bindings/pci/rcar-pci-ep.yaml | 76 +++++++++++++++++++
>> 1 file changed, 76 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml b/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
>> new file mode 100644
>> index 000000000000..99c2a1174463
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
>> @@ -0,0 +1,76 @@
>> +# SPDX-License-Identifier: GPL-2.0
>> +# Copyright (C) 2020 Renesas Electronics Europe GmbH - https://www.renesas.com/eu/en/
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/pci/rcar-pcie-ep.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Renesas R-Car PCIe Endpoint
>> +
>> +maintainers:
>> + - Lad Prabhakar <[email protected]>
>> +
>> +properties:
>> + compatible:
>> + items:
>> + - const: renesas,r8a774c0-pcie-ep
>> + - const: renesas,rcar-gen3-pcie-ep
>> +
>> + reg:
>> + maxItems: 5
>> +
>> + reg-names:
>> + items:
>> + - const: apb-base
>> + - const: memory0
>> + - const: memory1
>> + - const: memory2
>> + - const: memory3

As I had mentioned in the other patch, I'd prefer if we can create
standard binding for representing the memory regions. IMHO we should
create subnode for memory regions Each sub-node itself may or may not
have more than one memory region.

In your platform, since there can be only one allocation in a memory
region, there should be 4 sub-nodes for each of the memory region and
each node should have page_size (or some equivalent property) property
to indicate page_size (= region_size).

For a platform that doesn't have the restriction, there can be a single
sub-node containing all the memory region.

Let's wait for Rob's comment though.

Thanks
Kishon
>> +
>> + power-domains:
>> + maxItems: 1
>> +
>> + resets:
>> + maxItems: 1
>> +
>> + clocks:
>> + maxItems: 1
>> +
>> + clock-names:
>> + items:
>> + - const: pcie
>> +
>> + max-functions:
>> + minimum: 1
>> + maximum: 6
>> +
>> +required:
>> + - compatible
>> + - reg
>> + - reg-names
>> + - resets
>> + - power-domains
>> + - clocks
>> + - clock-names
>> + - max-functions
>> +
> apart from dt_binding_check error are we OK with dt bindings ?
>
> Cheers,
> --Prabhakar
>
>> +examples:
>> + - |
>> + #include <dt-bindings/clock/r8a774c0-cpg-mssr.h>
>> + #include <dt-bindings/power/r8a774c0-sysc.h>
>> +
>> + pcie0_ep: pcie-ep@fe000000 {
>> + compatible = "renesas,r8a774c0-pcie-ep",
>> + "renesas,rcar-gen3-pcie-ep";
>> + reg = <0 0xfe000000 0 0x80000>,
>> + <0x0 0xfe100000 0 0x100000>,
>> + <0x0 0xfe200000 0 0x200000>,
>> + <0x0 0x30000000 0 0x8000000>,
>> + <0x0 0x38000000 0 0x8000000>;
>> + reg-names = "apb-base", "memory0", "memory1", "memory2", "memory3";
>> + resets = <&cpg 319>;
>> + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>;
>> + clocks = <&cpg CPG_MOD 319>;
>> + clock-names = "pcie";
>> + max-functions = /bits/ 8 <1>;
>> + };
>> --
>> 2.20.1
>>

2020-01-30 20:56:55

by Lad, Prabhakar

[permalink] [raw]
Subject: Re: [v3 4/6] dt-bindings: PCI: rcar: Add bindings for R-Car PCIe endpoint controller

Hi Rob,

On Wed, Jan 22, 2020 at 8:13 AM Kishon Vijay Abraham I <[email protected]> wrote:
>
> Hi Prabhakar,
>
> On 21/01/20 11:27 PM, Lad, Prabhakar wrote:
> > Hi Rob/Kishon,
> >
> > On Wed, Jan 8, 2020 at 4:22 PM Lad Prabhakar <[email protected]> wrote:
> >>
> >> This patch adds the bindings for the R-Car PCIe endpoint driver.
> >>
> >> Signed-off-by: Lad Prabhakar <[email protected]>
> >> ---
> >> .../devicetree/bindings/pci/rcar-pci-ep.yaml | 76 +++++++++++++++++++
> >> 1 file changed, 76 insertions(+)
> >> create mode 100644 Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
> >>
> >> diff --git a/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml b/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
> >> new file mode 100644
> >> index 000000000000..99c2a1174463
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/pci/rcar-pci-ep.yaml
> >> @@ -0,0 +1,76 @@
> >> +# SPDX-License-Identifier: GPL-2.0
> >> +# Copyright (C) 2020 Renesas Electronics Europe GmbH - https://www.renesas.com/eu/en/
> >> +%YAML 1.2
> >> +---
> >> +$id: http://devicetree.org/schemas/pci/rcar-pcie-ep.yaml#
> >> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> >> +
> >> +title: Renesas R-Car PCIe Endpoint
> >> +
> >> +maintainers:
> >> + - Lad Prabhakar <[email protected]>
> >> +
> >> +properties:
> >> + compatible:
> >> + items:
> >> + - const: renesas,r8a774c0-pcie-ep
> >> + - const: renesas,rcar-gen3-pcie-ep
> >> +
> >> + reg:
> >> + maxItems: 5
> >> +
> >> + reg-names:
> >> + items:
> >> + - const: apb-base
> >> + - const: memory0
> >> + - const: memory1
> >> + - const: memory2
> >> + - const: memory3
>
> As I had mentioned in the other patch, I'd prefer if we can create
> standard binding for representing the memory regions. IMHO we should
> create subnode for memory regions Each sub-node itself may or may not
> have more than one memory region.
>
> In your platform, since there can be only one allocation in a memory
> region, there should be 4 sub-nodes for each of the memory region and
> each node should have page_size (or some equivalent property) property
> to indicate page_size (= region_size).
>
> For a platform that doesn't have the restriction, there can be a single
> sub-node containing all the memory region.
>
> Let's wait for Rob's comment though.
>
Gentle ping.on the suggestions above.

Cheers,
--Prabhakar

> Thanks
> Kishon
> >> +
> >> + power-domains:
> >> + maxItems: 1
> >> +
> >> + resets:
> >> + maxItems: 1
> >> +
> >> + clocks:
> >> + maxItems: 1
> >> +
> >> + clock-names:
> >> + items:
> >> + - const: pcie
> >> +
> >> + max-functions:
> >> + minimum: 1
> >> + maximum: 6
> >> +
> >> +required:
> >> + - compatible
> >> + - reg
> >> + - reg-names
> >> + - resets
> >> + - power-domains
> >> + - clocks
> >> + - clock-names
> >> + - max-functions
> >> +
> > apart from dt_binding_check error are we OK with dt bindings ?
> >
> > Cheers,
> > --Prabhakar
> >
> >> +examples:
> >> + - |
> >> + #include <dt-bindings/clock/r8a774c0-cpg-mssr.h>
> >> + #include <dt-bindings/power/r8a774c0-sysc.h>
> >> +
> >> + pcie0_ep: pcie-ep@fe000000 {
> >> + compatible = "renesas,r8a774c0-pcie-ep",
> >> + "renesas,rcar-gen3-pcie-ep";
> >> + reg = <0 0xfe000000 0 0x80000>,
> >> + <0x0 0xfe100000 0 0x100000>,
> >> + <0x0 0xfe200000 0 0x200000>,
> >> + <0x0 0x30000000 0 0x8000000>,
> >> + <0x0 0x38000000 0 0x8000000>;
> >> + reg-names = "apb-base", "memory0", "memory1", "memory2", "memory3";
> >> + resets = <&cpg 319>;
> >> + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>;
> >> + clocks = <&cpg CPG_MOD 319>;
> >> + clock-names = "pcie";
> >> + max-functions = /bits/ 8 <1>;
> >> + };
> >> --
> >> 2.20.1
> >>