The 8-bit ov7725 sensors can also be connected to the camera daughter
board.
This patch creates a separate dtsi file for ov7725 sensors and is included
in r8a7742-iwg21d-q7-dbcm-ca.dts. The user can set VINx_SENSOR depending
on the cameras connected.
Signed-off-by: Lad Prabhakar <[email protected]>
Reviewed-by: Biju Das <[email protected]>
---
.../boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts | 7 ++
.../dts/r8a7742-iwg21d-q7-dbcm-ov7725.dtsi | 112 ++++++++++++++++++
2 files changed, 119 insertions(+)
create mode 100644 arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov7725.dtsi
diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
index 1ab4f9771a34..915ff5fd437c 100644
--- a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
+++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
@@ -11,6 +11,7 @@
#define SENSOR_NONE 1
#define SENSOR_OV5640 2
+#define SENSOR_OV7725 3
/* 8bit CMOS Camera 1 (J13) */
#define CAM1_PARENT_I2C i2c0
@@ -40,6 +41,11 @@
* VIN2 interface and also the ov5640 node connected to it)
* #define VIN2_SENSOR SENSOR_NONE
*
+ * To tie VINx endpoints to ov7725_x endpoints set VINx_SENSOR to
+ * SENSOR_OV7725 for example if ov7725_3 is connected to the VIN3
+ * interface set the below (this disables the ov5640_3)
+ * #define VIN3_SENSOR SENSOR_OV7725
+ *
*/
#define VIN0_SENSOR SENSOR_OV5640
#define VIN1_SENSOR SENSOR_OV5640
@@ -47,6 +53,7 @@
#define VIN3_SENSOR SENSOR_OV5640
#include "r8a7742-iwg21d-q7-dbcm-ov5640.dtsi"
+#include "r8a7742-iwg21d-q7-dbcm-ov7725.dtsi"
#if (VIN0_SENSOR == SENSOR_NONE)
#undef VIN0_REMOTE_EP
diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov7725.dtsi b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov7725.dtsi
new file mode 100644
index 000000000000..054d0a7cc5ce
--- /dev/null
+++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov7725.dtsi
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * This include file ties VIN interfaces with ov7725 sensors on
+ * iWave-RZ/G1H Qseven board development platform connected with
+ * camera daughter board.
+ *
+ * Copyright (C) 2020 Renesas Electronics Corp.
+ */
+
+#if (VIN0_SENSOR == SENSOR_OV7725)
+#define OV7725_0_STATUS "okay"
+#define OV7725_0_REMOTE_EP &VIN0_EP
+#define VIN0_REMOTE_EP &ov7725_0
+#else
+#define OV7725_0_STATUS "disabled"
+#define OV7725_0_REMOTE_EP 0
+#endif
+
+#if (VIN1_SENSOR == SENSOR_OV7725)
+#define OV7725_1_STATUS "okay"
+#define OV7725_1_REMOTE_EP &VIN1_EP
+#define VIN1_REMOTE_EP &ov7725_1
+#else
+#define OV7725_1_STATUS "disabled"
+#define OV7725_1_REMOTE_EP 0
+#endif
+
+#if (VIN2_SENSOR == SENSOR_OV7725)
+#define OV7725_2_STATUS "okay"
+#define OV7725_2_REMOTE_EP &VIN2_EP
+#define VIN2_REMOTE_EP &ov7725_2
+#else
+#define OV7725_2_STATUS "disabled"
+#define OV7725_2_REMOTE_EP 0
+#endif
+
+#if (VIN3_SENSOR == SENSOR_OV7725)
+#define OV7725_3_STATUS "okay"
+#define OV7725_3_REMOTE_EP &VIN3_EP
+#define VIN3_REMOTE_EP &ov7725_3
+#else
+#define OV7725_3_STATUS "disabled"
+#define OV7725_3_REMOTE_EP 0
+#endif
+
+&CAM1_PARENT_I2C {
+ ov7725@21 {
+ compatible = "ovti,ov7725";
+ reg = <0x21>;
+ clocks = <&MCLK_CAM1>;
+ status = OV7725_0_STATUS;
+
+ port {
+ ov7725_0: endpoint {
+ bus-width = <8>;
+ bus-type = <6>;
+ remote-endpoint = <OV7725_0_REMOTE_EP>;
+ };
+ };
+ };
+};
+
+&CAM2_PARENT_I2C {
+ ov7725@21 {
+ compatible = "ovti,ov7725";
+ reg = <0x21>;
+ clocks = <&MCLK_CAM2>;
+ status = OV7725_1_STATUS;
+
+ port {
+ ov7725_1: endpoint {
+ bus-width = <8>;
+ bus-type = <6>;
+ remote-endpoint = <OV7725_1_REMOTE_EP>;
+ };
+ };
+ };
+};
+
+&CAM3_PARENT_I2C {
+ ov7725@21 {
+ compatible = "ovti,ov7725";
+ reg = <0x21>;
+ clocks = <&MCLK_CAM3>;
+ status = OV7725_2_STATUS;
+
+ port {
+ ov7725_2: endpoint {
+ bus-width = <8>;
+ bus-type = <6>;
+ remote-endpoint = <OV7725_2_REMOTE_EP>;
+ };
+ };
+ };
+};
+
+&CAM4_PARENT_I2C {
+ ov7725@21 {
+ compatible = "ovti,ov7725";
+ reg = <0x21>;
+ clocks = <&MCLK_CAM4>;
+ status = OV7725_3_STATUS;
+
+ port {
+ ov7725_3: endpoint {
+ bus-width = <8>;
+ bus-type = <6>;
+ remote-endpoint = <OV7725_3_REMOTE_EP>;
+ };
+ };
+ };
+};
--
2.17.1
Hi Prabhakar,
On Thu, Nov 26, 2020 at 11:31 AM Lad Prabhakar
<[email protected]> wrote:
> The 8-bit ov7725 sensors can also be connected to the camera daughter
> board.
>
> This patch creates a separate dtsi file for ov7725 sensors and is included
> in r8a7742-iwg21d-q7-dbcm-ca.dts. The user can set VINx_SENSOR depending
> on the cameras connected.
>
> Signed-off-by: Lad Prabhakar <[email protected]>
> Reviewed-by: Biju Das <[email protected]>
Thanks for your patch!
Reviewed-by: Geert Uytterhoeven <[email protected]>
However, I think this can still be improved upon. As it's a bit difficult
to explain, I'll send an updated version of your series with my
suggestions applied.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Hello,
On Thu, Nov 26, 2020 at 10:30:53AM +0000, Lad Prabhakar wrote:
> The 8-bit ov7725 sensors can also be connected to the camera daughter
> board.
>
> This patch creates a separate dtsi file for ov7725 sensors and is included
> in r8a7742-iwg21d-q7-dbcm-ca.dts. The user can set VINx_SENSOR depending
> on the cameras connected.
>
> Signed-off-by: Lad Prabhakar <[email protected]>
> Reviewed-by: Biju Das <[email protected]>
> ---
> .../boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts | 7 ++
> .../dts/r8a7742-iwg21d-q7-dbcm-ov7725.dtsi | 112 ++++++++++++++++++
> 2 files changed, 119 insertions(+)
> create mode 100644 arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov7725.dtsi
>
> diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
> index 1ab4f9771a34..915ff5fd437c 100644
> --- a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
> +++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
> @@ -11,6 +11,7 @@
>
> #define SENSOR_NONE 1
> #define SENSOR_OV5640 2
> +#define SENSOR_OV7725 3
>
> /* 8bit CMOS Camera 1 (J13) */
> #define CAM1_PARENT_I2C i2c0
> @@ -40,6 +41,11 @@
> * VIN2 interface and also the ov5640 node connected to it)
> * #define VIN2_SENSOR SENSOR_NONE
> *
> + * To tie VINx endpoints to ov7725_x endpoints set VINx_SENSOR to
> + * SENSOR_OV7725 for example if ov7725_3 is connected to the VIN3
> + * interface set the below (this disables the ov5640_3)
> + * #define VIN3_SENSOR SENSOR_OV7725
> + *
> */
> #define VIN0_SENSOR SENSOR_OV5640
> #define VIN1_SENSOR SENSOR_OV5640
> @@ -47,6 +53,7 @@
> #define VIN3_SENSOR SENSOR_OV5640
>
> #include "r8a7742-iwg21d-q7-dbcm-ov5640.dtsi"
> +#include "r8a7742-iwg21d-q7-dbcm-ov7725.dtsi"
Mmm, can't we alternatively include one .dtsi or the other depending
on a define symbol ? The .dtsi describe pluggable expansion boards,
they cannot be mixed, right ?
Thanks
j
>
> #if (VIN0_SENSOR == SENSOR_NONE)
> #undef VIN0_REMOTE_EP
> diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov7725.dtsi b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov7725.dtsi
> new file mode 100644
> index 000000000000..054d0a7cc5ce
> --- /dev/null
> +++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov7725.dtsi
> @@ -0,0 +1,112 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * This include file ties VIN interfaces with ov7725 sensors on
> + * iWave-RZ/G1H Qseven board development platform connected with
> + * camera daughter board.
> + *
> + * Copyright (C) 2020 Renesas Electronics Corp.
> + */
> +
> +#if (VIN0_SENSOR == SENSOR_OV7725)
> +#define OV7725_0_STATUS "okay"
> +#define OV7725_0_REMOTE_EP &VIN0_EP
> +#define VIN0_REMOTE_EP &ov7725_0
> +#else
> +#define OV7725_0_STATUS "disabled"
> +#define OV7725_0_REMOTE_EP 0
> +#endif
> +
> +#if (VIN1_SENSOR == SENSOR_OV7725)
> +#define OV7725_1_STATUS "okay"
> +#define OV7725_1_REMOTE_EP &VIN1_EP
> +#define VIN1_REMOTE_EP &ov7725_1
> +#else
> +#define OV7725_1_STATUS "disabled"
> +#define OV7725_1_REMOTE_EP 0
> +#endif
> +
> +#if (VIN2_SENSOR == SENSOR_OV7725)
> +#define OV7725_2_STATUS "okay"
> +#define OV7725_2_REMOTE_EP &VIN2_EP
> +#define VIN2_REMOTE_EP &ov7725_2
> +#else
> +#define OV7725_2_STATUS "disabled"
> +#define OV7725_2_REMOTE_EP 0
> +#endif
> +
> +#if (VIN3_SENSOR == SENSOR_OV7725)
> +#define OV7725_3_STATUS "okay"
> +#define OV7725_3_REMOTE_EP &VIN3_EP
> +#define VIN3_REMOTE_EP &ov7725_3
> +#else
> +#define OV7725_3_STATUS "disabled"
> +#define OV7725_3_REMOTE_EP 0
> +#endif
> +
> +&CAM1_PARENT_I2C {
> + ov7725@21 {
> + compatible = "ovti,ov7725";
> + reg = <0x21>;
> + clocks = <&MCLK_CAM1>;
> + status = OV7725_0_STATUS;
> +
> + port {
> + ov7725_0: endpoint {
> + bus-width = <8>;
> + bus-type = <6>;
> + remote-endpoint = <OV7725_0_REMOTE_EP>;
> + };
> + };
> + };
> +};
> +
> +&CAM2_PARENT_I2C {
> + ov7725@21 {
> + compatible = "ovti,ov7725";
> + reg = <0x21>;
> + clocks = <&MCLK_CAM2>;
> + status = OV7725_1_STATUS;
> +
> + port {
> + ov7725_1: endpoint {
> + bus-width = <8>;
> + bus-type = <6>;
> + remote-endpoint = <OV7725_1_REMOTE_EP>;
> + };
> + };
> + };
> +};
> +
> +&CAM3_PARENT_I2C {
> + ov7725@21 {
> + compatible = "ovti,ov7725";
> + reg = <0x21>;
> + clocks = <&MCLK_CAM3>;
> + status = OV7725_2_STATUS;
> +
> + port {
> + ov7725_2: endpoint {
> + bus-width = <8>;
> + bus-type = <6>;
> + remote-endpoint = <OV7725_2_REMOTE_EP>;
> + };
> + };
> + };
> +};
> +
> +&CAM4_PARENT_I2C {
> + ov7725@21 {
> + compatible = "ovti,ov7725";
> + reg = <0x21>;
> + clocks = <&MCLK_CAM4>;
> + status = OV7725_3_STATUS;
> +
> + port {
> + ov7725_3: endpoint {
> + bus-width = <8>;
> + bus-type = <6>;
> + remote-endpoint = <OV7725_3_REMOTE_EP>;
> + };
> + };
> + };
> +};
> --
> 2.17.1
>
Hi Jacopo,
Thank you for the review.
On Tue, Dec 15, 2020 at 11:49 AM Jacopo Mondi <[email protected]> wrote:
>
> Hello,
>
> On Thu, Nov 26, 2020 at 10:30:53AM +0000, Lad Prabhakar wrote:
> > The 8-bit ov7725 sensors can also be connected to the camera daughter
> > board.
> >
> > This patch creates a separate dtsi file for ov7725 sensors and is included
> > in r8a7742-iwg21d-q7-dbcm-ca.dts. The user can set VINx_SENSOR depending
> > on the cameras connected.
> >
> > Signed-off-by: Lad Prabhakar <[email protected]>
> > Reviewed-by: Biju Das <[email protected]>
> > ---
> > .../boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts | 7 ++
> > .../dts/r8a7742-iwg21d-q7-dbcm-ov7725.dtsi | 112 ++++++++++++++++++
> > 2 files changed, 119 insertions(+)
> > create mode 100644 arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov7725.dtsi
> >
> > diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
> > index 1ab4f9771a34..915ff5fd437c 100644
> > --- a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
> > +++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
> > @@ -11,6 +11,7 @@
> >
> > #define SENSOR_NONE 1
> > #define SENSOR_OV5640 2
> > +#define SENSOR_OV7725 3
> >
> > /* 8bit CMOS Camera 1 (J13) */
> > #define CAM1_PARENT_I2C i2c0
> > @@ -40,6 +41,11 @@
> > * VIN2 interface and also the ov5640 node connected to it)
> > * #define VIN2_SENSOR SENSOR_NONE
> > *
> > + * To tie VINx endpoints to ov7725_x endpoints set VINx_SENSOR to
> > + * SENSOR_OV7725 for example if ov7725_3 is connected to the VIN3
> > + * interface set the below (this disables the ov5640_3)
> > + * #define VIN3_SENSOR SENSOR_OV7725
> > + *
> > */
> > #define VIN0_SENSOR SENSOR_OV5640
> > #define VIN1_SENSOR SENSOR_OV5640
> > @@ -47,6 +53,7 @@
> > #define VIN3_SENSOR SENSOR_OV5640
> >
> > #include "r8a7742-iwg21d-q7-dbcm-ov5640.dtsi"
> > +#include "r8a7742-iwg21d-q7-dbcm-ov7725.dtsi"
>
> Mmm, can't we alternatively include one .dtsi or the other depending
> on a define symbol ? The .dtsi describe pluggable expansion boards,
> they cannot be mixed, right ?
>
Since the cameras on the daughter can be mixed and matched a much
better version of the patches [1] which handle this case elegantly has
been posted by Geert.
[1] https://patchwork.kernel.org/project/linux-renesas-soc/cover/[email protected]/
Cheers,
Prabhakar
Hi Prabhakar,
On Tue, Dec 15, 2020 at 03:57:32PM +0000, Lad, Prabhakar wrote:
> Hi Jacopo,
>
> Thank you for the review.
>
> On Tue, Dec 15, 2020 at 11:49 AM Jacopo Mondi <[email protected]> wrote:
> >
> > Hello,
> >
> > On Thu, Nov 26, 2020 at 10:30:53AM +0000, Lad Prabhakar wrote:
> > > The 8-bit ov7725 sensors can also be connected to the camera daughter
> > > board.
> > >
> > > This patch creates a separate dtsi file for ov7725 sensors and is included
> > > in r8a7742-iwg21d-q7-dbcm-ca.dts. The user can set VINx_SENSOR depending
> > > on the cameras connected.
> > >
> > > Signed-off-by: Lad Prabhakar <[email protected]>
> > > Reviewed-by: Biju Das <[email protected]>
> > > ---
> > > .../boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts | 7 ++
> > > .../dts/r8a7742-iwg21d-q7-dbcm-ov7725.dtsi | 112 ++++++++++++++++++
> > > 2 files changed, 119 insertions(+)
> > > create mode 100644 arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov7725.dtsi
> > >
> > > diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
> > > index 1ab4f9771a34..915ff5fd437c 100644
> > > --- a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
> > > +++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
> > > @@ -11,6 +11,7 @@
> > >
> > > #define SENSOR_NONE 1
> > > #define SENSOR_OV5640 2
> > > +#define SENSOR_OV7725 3
> > >
> > > /* 8bit CMOS Camera 1 (J13) */
> > > #define CAM1_PARENT_I2C i2c0
> > > @@ -40,6 +41,11 @@
> > > * VIN2 interface and also the ov5640 node connected to it)
> > > * #define VIN2_SENSOR SENSOR_NONE
> > > *
> > > + * To tie VINx endpoints to ov7725_x endpoints set VINx_SENSOR to
> > > + * SENSOR_OV7725 for example if ov7725_3 is connected to the VIN3
> > > + * interface set the below (this disables the ov5640_3)
> > > + * #define VIN3_SENSOR SENSOR_OV7725
> > > + *
> > > */
> > > #define VIN0_SENSOR SENSOR_OV5640
> > > #define VIN1_SENSOR SENSOR_OV5640
> > > @@ -47,6 +53,7 @@
> > > #define VIN3_SENSOR SENSOR_OV5640
> > >
> > > #include "r8a7742-iwg21d-q7-dbcm-ov5640.dtsi"
> > > +#include "r8a7742-iwg21d-q7-dbcm-ov7725.dtsi"
> >
> > Mmm, can't we alternatively include one .dtsi or the other depending
> > on a define symbol ? The .dtsi describe pluggable expansion boards,
> > they cannot be mixed, right ?
> >
> Since the cameras on the daughter can be mixed and matched a much
> better version of the patches [1] which handle this case elegantly has
> been posted by Geert.
>
> [1] https://patchwork.kernel.org/project/linux-renesas-soc/cover/[email protected]/
Oh, I see the discussion know, sorry for the noise.
>
> Cheers,
> Prabhakar