2015-11-14 22:05:57

by Ondrej Zary

Subject: [PATCH 1/2] dl2k: Add support for IP1000A-based cards

Add support for IP1000A chips to dl2k driver.
IP1000A chip looks like a TC9020 with integrated PHY.

This allows IP1000A chips to work reliably because the ipg driver is
buggy - it loses packets under load and then completely stops
transmitting data.

Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps.
Also verified that it does not break D-Link DGE-550T.

Signed-off-by: Ondrej Zary <[email protected]>
---
drivers/net/ethernet/dlink/Kconfig | 5 ++--
drivers/net/ethernet/dlink/dl2k.c | 51 +++++++++++++++++++++++++++++++++---
drivers/net/ethernet/dlink/dl2k.h | 15 ++++++++++-
3 files changed, 65 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ethernet/dlink/Kconfig b/drivers/net/ethernet/dlink/Kconfig
index f6e858d..ebdc832 100644
--- a/drivers/net/ethernet/dlink/Kconfig
+++ b/drivers/net/ethernet/dlink/Kconfig
@@ -17,15 +17,16 @@ config NET_VENDOR_DLINK
if NET_VENDOR_DLINK

config DL2K
- tristate "DL2000/TC902x-based Gigabit Ethernet support"
+ tristate "DL2000/TC902x/IP1000A-based Gigabit Ethernet support"
depends on PCI
select CRC32
---help---
- This driver supports DL2000/TC902x-based Gigabit ethernet cards,
+ This driver supports DL2000/TC902x/IP1000A-based Gigabit ethernet cards,
which includes
D-Link DGE-550T Gigabit Ethernet Adapter.
D-Link DL2000-based Gigabit Ethernet Adapter.
Sundance/Tamarack TC902x Gigabit Ethernet Adapter.
+ ICPlus IP1000A-based cards

To compile this driver as a module, choose M here: the
module will be called dl2k.
diff --git a/drivers/net/ethernet/dlink/dl2k.c b/drivers/net/ethernet/dlink/dl2k.c
index cf0a5fc..c8a1cfd 100644
--- a/drivers/net/ethernet/dlink/dl2k.c
+++ b/drivers/net/ethernet/dlink/dl2k.c
@@ -253,6 +253,18 @@ rio_probe1 (struct pci_dev *pdev, const struct pci_device_id *ent)
if (err)
goto err_out_unmap_rx;

+ if (np->chip_id == CHIP_IP1000A &&
+ (np->pdev->revision == 0x40 || np->pdev->revision == 0x41)) {
+ /* PHY magic taken from ipg driver */
+ mii_write(dev, np->phy_addr, 31, 0x0001);
+ mii_write(dev, np->phy_addr, 27, 0x01e0);
+ mii_write(dev, np->phy_addr, 31, 0x0002);
+ mii_write(dev, np->phy_addr, 27, 0xeb8e);
+ mii_write(dev, np->phy_addr, 31, 0x0000);
+ mii_write(dev, np->phy_addr, 30, 0x005e);
+ mii_write(dev, np->phy_addr, 9, 0x0700);
+ }
+
/* Fiber device? */
np->phy_media = (dr16(ASICCtrl) & PhyMedia) ? 1 : 0;
np->link_status = 0;
@@ -361,6 +373,11 @@ parse_eeprom (struct net_device *dev)
for (i = 0; i < 6; i++)
dev->dev_addr[i] = psrom->mac_addr[i];

+ if (np->chip_id == CHIP_IP1000A) {
+ np->led_mode = psrom->led_mode;
+ return 0;
+ }
+
if (np->pdev->vendor != PCI_VENDOR_ID_DLINK) {
return 0;
}
@@ -406,6 +423,28 @@ parse_eeprom (struct net_device *dev)
return 0;
}

+static void rio_set_led_mode(struct net_device *dev)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ void __iomem *ioaddr = np->ioaddr;
+ u32 mode;
+
+ if (np->chip_id != CHIP_IP1000A)
+ return;
+
+ mode = dr32(ASICCtrl);
+ mode &= ~(IPG_AC_LED_MODE_BIT_1 | IPG_AC_LED_MODE | IPG_AC_LED_SPEED);
+
+ if ((np->led_mode & 0x03) > 1)
+ mode |= IPG_AC_LED_MODE_BIT_1;
+ if ((np->led_mode & 0x01) == 1)
+ mode |= IPG_AC_LED_MODE;
+ if ((np->led_mode & 0x08) == 8)
+ mode |= IPG_AC_LED_SPEED;
+
+ dw32(ASICCtrl, mode);
+}
+
static int
rio_open (struct net_device *dev)
{
@@ -424,6 +463,8 @@ rio_open (struct net_device *dev)
GlobalReset | DMAReset | FIFOReset | NetworkReset | HostReset);
mdelay(10);

+ rio_set_led_mode(dev);
+
/* DebugCtrl bit 4, 5, 9 must set */
dw32(DebugCtrl, dr32(DebugCtrl) | 0x0230);

@@ -433,9 +474,10 @@ rio_open (struct net_device *dev)

alloc_list (dev);

- /* Get station address */
- for (i = 0; i < 6; i++)
- dw8(StationAddr0 + i, dev->dev_addr[i]);
+ /* Set station address */
+ for (i = 0; i < 3; i++)
+ dw16(StationAddr0 + 2 * i,
+ cpu_to_le16(((u16 *)dev->dev_addr)[i]));

set_multicast (dev);
if (np->coalesce) {
@@ -780,6 +822,7 @@ tx_error (struct net_device *dev, int tx_status)
break;
mdelay (1);
}
+ rio_set_led_mode(dev);
rio_free_tx (dev, 1);
/* Reset TFDListPtr */
dw32(TFDListPtr0, np->tx_ring_dma +
@@ -799,6 +842,7 @@ tx_error (struct net_device *dev, int tx_status)
break;
mdelay (1);
}
+ rio_set_led_mode(dev);
/* Let TxStartThresh stay default value */
}
/* Maximum Collisions */
@@ -965,6 +1009,7 @@ rio_error (struct net_device *dev, int int_status)
dev->name, int_status);
dw16(ASICCtrl + 2, GlobalReset | HostReset);
mdelay (500);
+ rio_set_led_mode(dev);
}
}

diff --git a/drivers/net/ethernet/dlink/dl2k.h b/drivers/net/ethernet/dlink/dl2k.h
index 23c07b0..8f4f612 100644
--- a/drivers/net/ethernet/dlink/dl2k.h
+++ b/drivers/net/ethernet/dlink/dl2k.h
@@ -211,6 +211,10 @@ enum ASICCtrl_HiWord_bits {
ResetBusy = 0x0400,
};

+#define IPG_AC_LED_MODE BIT(14)
+#define IPG_AC_LED_SPEED BIT(27)
+#define IPG_AC_LED_MODE_BIT_1 BIT(29)
+
/* Transmit Frame Control bits */
enum TFC_bits {
DwordAlign = 0x00000000,
@@ -332,7 +336,10 @@ typedef struct t_SROM {
u16 asic_ctrl; /* 0x02 */
u16 sub_vendor_id; /* 0x04 */
u16 sub_system_id; /* 0x06 */
- u16 reserved1[12]; /* 0x08-0x1f */
+ u16 pci_base_1; /* 0x08 (IP1000A only) */
+ u16 pci_base_2; /* 0x0a (IP1000A only) */
+ u16 led_mode; /* 0x0c (IP1000A only) */
+ u16 reserved1[9]; /* 0x0e-0x1f */
u8 mac_addr[6]; /* 0x20-0x25 */
u8 reserved2[10]; /* 0x26-0x2f */
u8 sib[204]; /* 0x30-0xfb */
@@ -397,6 +404,7 @@ struct netdev_private {
u16 advertising; /* NWay media advertisement */
u16 negotiate; /* Negotiated media */
int phy_addr; /* PHY addresses. */
+ u16 led_mode; /* LED mode read from EEPROM (IP1000A only) */
};

/* The station address location in the EEPROM. */
@@ -407,10 +415,15 @@ struct netdev_private {
class_mask of the class are honored during the comparison.
driver_data Data private to the driver.
*/
+#define CHIP_IP1000A 1

static const struct pci_device_id rio_pci_tbl[] = {
{0x1186, 0x4000, PCI_ANY_ID, PCI_ANY_ID, },
{0x13f0, 0x1021, PCI_ANY_ID, PCI_ANY_ID, },
+ { PCI_VDEVICE(SUNDANCE, 0x1023), CHIP_IP1000A },
+ { PCI_VDEVICE(SUNDANCE, 0x2021), CHIP_IP1000A },
+ { PCI_VDEVICE(DLINK, 0x9021), CHIP_IP1000A },
+ { PCI_VDEVICE(DLINK, 0x4020), CHIP_IP1000A },
{ }
};
MODULE_DEVICE_TABLE (pci, rio_pci_tbl);
--
Ondrej Zary

2015-11-14 22:06:15

by Ondrej Zary

Subject: [PATCH 2/2] ipg: Remove ipg driver

Now that IP1000A chips are supported by dl2k driver, the buggy ipg
driver can be removed. The ipg driver loses packets under load and then
completely stops transmitting data.


Signed-off-by: Ondrej Zary <[email protected]>
---
MAINTAINERS | 7 -
drivers/net/ethernet/Kconfig | 1 -
drivers/net/ethernet/Makefile | 1 -
drivers/net/ethernet/icplus/Kconfig | 13 -
drivers/net/ethernet/icplus/Makefile | 5 -
drivers/net/ethernet/icplus/ipg.c | 2300 ----------------------------------
drivers/net/ethernet/icplus/ipg.h | 748 -----------
7 files changed, 3075 deletions(-)
delete mode 100644 drivers/net/ethernet/icplus/Kconfig
delete mode 100644 drivers/net/ethernet/icplus/Makefile
delete mode 100644 drivers/net/ethernet/icplus/ipg.c
delete mode 100644 drivers/net/ethernet/icplus/ipg.h

diff --git a/MAINTAINERS b/MAINTAINERS
index 7ba7ab7..b683820 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5588,13 +5588,6 @@ M: Juanjo Ciarlante <[email protected]>
S: Maintained
F: net/ipv4/netfilter/ipt_MASQUERADE.c

-IP1000A 10/100/1000 GIGABIT ETHERNET DRIVER
-M: Francois Romieu <[email protected]>
-M: Sorbica Shieh <[email protected]>
-L: [email protected]
-S: Maintained
-F: drivers/net/ethernet/icplus/ipg.*
-
IPATH DRIVER
M: Mike Marciniszyn <[email protected]>
L: [email protected]
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 05aa759..955d06b 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -78,7 +78,6 @@ source "drivers/net/ethernet/ibm/Kconfig"
source "drivers/net/ethernet/intel/Kconfig"
source "drivers/net/ethernet/i825xx/Kconfig"
source "drivers/net/ethernet/xscale/Kconfig"
-source "drivers/net/ethernet/icplus/Kconfig"

config JME
tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index ddfc808..4a2ee98 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -41,7 +41,6 @@ obj-$(CONFIG_NET_VENDOR_IBM) += ibm/
obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
obj-$(CONFIG_NET_VENDOR_I825XX) += i825xx/
obj-$(CONFIG_NET_VENDOR_XSCALE) += xscale/
-obj-$(CONFIG_IP1000) += icplus/
obj-$(CONFIG_JME) += jme.o
obj-$(CONFIG_KORINA) += korina.o
obj-$(CONFIG_LANTIQ_ETOP) += lantiq_etop.o
diff --git a/drivers/net/ethernet/icplus/Kconfig b/drivers/net/ethernet/icplus/Kconfig
deleted file mode 100644
index 14a66e9..0000000
--- a/drivers/net/ethernet/icplus/Kconfig
+++ /dev/null
@@ -1,13 +0,0 @@
-#
-# IC Plus device configuration
-#
-
-config IP1000
- tristate "IP1000 Gigabit Ethernet support"
- depends on PCI
- select MII
- ---help---
- This driver supports IP1000 gigabit Ethernet cards.
-
- To compile this driver as a module, choose M here: the module
- will be called ipg. This is recommended.
diff --git a/drivers/net/ethernet/icplus/Makefile b/drivers/net/ethernet/icplus/Makefile
deleted file mode 100644
index 5bc87c1..0000000
--- a/drivers/net/ethernet/icplus/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-#
-# Makefile for the IC Plus device drivers
-#
-
-obj-$(CONFIG_IP1000) += ipg.o
diff --git a/drivers/net/ethernet/icplus/ipg.c b/drivers/net/ethernet/icplus/ipg.c
deleted file mode 100644
index c3b6af8..0000000
--- a/drivers/net/ethernet/icplus/ipg.c
+++ /dev/null
@@ -1,2300 +0,0 @@
-/*
- * ipg.c: Device Driver for the IP1000 Gigabit Ethernet Adapter
- *
- * Copyright (C) 2003, 2007 IC Plus Corp
- *
- * Original Author:
- *
- * Craig Rich
- * Sundance Technology, Inc.
- * http://www.sundanceti.com
- * [email protected]
- *
- * Current Maintainer:
- *
- * Sorbica Shieh.
- * http://www.icplus.com.tw
- * [email protected]
- *
- * Jesse Huang
- * http://www.icplus.com.tw
- * [email protected]
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/crc32.h>
-#include <linux/ethtool.h>
-#include <linux/interrupt.h>
-#include <linux/gfp.h>
-#include <linux/mii.h>
-#include <linux/mutex.h>
-
-#include <asm/div64.h>
-
-#define IPG_RX_RING_BYTES (sizeof(struct ipg_rx) * IPG_RFDLIST_LENGTH)
-#define IPG_TX_RING_BYTES (sizeof(struct ipg_tx) * IPG_TFDLIST_LENGTH)
-#define IPG_RESET_MASK \
- (IPG_AC_GLOBAL_RESET | IPG_AC_RX_RESET | IPG_AC_TX_RESET | \
- IPG_AC_DMA | IPG_AC_FIFO | IPG_AC_NETWORK | IPG_AC_HOST | \
- IPG_AC_AUTO_INIT)
-
-#define ipg_w32(val32, reg) iowrite32((val32), ioaddr + (reg))
-#define ipg_w16(val16, reg) iowrite16((val16), ioaddr + (reg))
-#define ipg_w8(val8, reg) iowrite8((val8), ioaddr + (reg))
-
-#define ipg_r32(reg) ioread32(ioaddr + (reg))
-#define ipg_r16(reg) ioread16(ioaddr + (reg))
-#define ipg_r8(reg) ioread8(ioaddr + (reg))
-
-enum {
- netdev_io_size = 128
-};
-
-#include "ipg.h"
-#define DRV_NAME "ipg"
-
-MODULE_AUTHOR("IC Plus Corp. 2003");
-MODULE_DESCRIPTION("IC Plus IP1000 Gigabit Ethernet Adapter Linux Driver");
-MODULE_LICENSE("GPL");
-
-/*
- * Defaults
- */
-#define IPG_MAX_RXFRAME_SIZE 0x0600
-#define IPG_RXFRAG_SIZE 0x0600
-#define IPG_RXSUPPORT_SIZE 0x0600
-#define IPG_IS_JUMBO false
-
-/*
- * Variable record -- index by leading revision/length
- * Revision/Length(=N*4), Address1, Data1, Address2, Data2,...,AddressN,DataN
- */
-static const unsigned short DefaultPhyParam[] = {
- /* 11/12/03 IP1000A v1-3 rev=0x40 */
- /*--------------------------------------------------------------------------
- (0x4000|(15*4)), 31, 0x0001, 27, 0x01e0, 31, 0x0002, 22, 0x85bd, 24, 0xfff2,
- 27, 0x0c10, 28, 0x0c10, 29, 0x2c10, 31, 0x0003, 23, 0x92f6,
- 31, 0x0000, 23, 0x003d, 30, 0x00de, 20, 0x20e7, 9, 0x0700,
- --------------------------------------------------------------------------*/
- /* 12/17/03 IP1000A v1-4 rev=0x40 */
- (0x4000 | (07 * 4)), 31, 0x0001, 27, 0x01e0, 31, 0x0002, 27, 0xeb8e, 31,
- 0x0000,
- 30, 0x005e, 9, 0x0700,
- /* 01/09/04 IP1000A v1-5 rev=0x41 */
- (0x4100 | (07 * 4)), 31, 0x0001, 27, 0x01e0, 31, 0x0002, 27, 0xeb8e, 31,
- 0x0000,
- 30, 0x005e, 9, 0x0700,
- 0x0000
-};
-
-static const char * const ipg_brand_name[] = {
- "IC PLUS IP1000 1000/100/10 based NIC",
- "Sundance Technology ST2021 based NIC",
- "Tamarack Microelectronics TC9020/9021 based NIC",
- "D-Link NIC IP1000A"
-};
-
-static const struct pci_device_id ipg_pci_tbl[] = {
- { PCI_VDEVICE(SUNDANCE, 0x1023), 0 },
- { PCI_VDEVICE(SUNDANCE, 0x2021), 1 },
- { PCI_VDEVICE(DLINK, 0x9021), 2 },
- { PCI_VDEVICE(DLINK, 0x4020), 3 },
- { 0, }
-};
-
-MODULE_DEVICE_TABLE(pci, ipg_pci_tbl);
-
-static inline void __iomem *ipg_ioaddr(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- return sp->ioaddr;
-}
-
-#ifdef IPG_DEBUG
-static void ipg_dump_rfdlist(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int i;
- u32 offset;
-
- IPG_DEBUG_MSG("_dump_rfdlist\n");
-
- netdev_info(dev, "rx_current = %02x\n", sp->rx_current);
- netdev_info(dev, "rx_dirty = %02x\n", sp->rx_dirty);
- netdev_info(dev, "RFDList start address = %016lx\n",
- (unsigned long)sp->rxd_map);
- netdev_info(dev, "RFDListPtr register = %08x%08x\n",
- ipg_r32(IPG_RFDLISTPTR1), ipg_r32(IPG_RFDLISTPTR0));
-
- for (i = 0; i < IPG_RFDLIST_LENGTH; i++) {
- offset = (u32) &sp->rxd[i].next_desc - (u32) sp->rxd;
- netdev_info(dev, "%02x %04x RFDNextPtr = %016lx\n",
- i, offset, (unsigned long)sp->rxd[i].next_desc);
- offset = (u32) &sp->rxd[i].rfs - (u32) sp->rxd;
- netdev_info(dev, "%02x %04x RFS = %016lx\n",
- i, offset, (unsigned long)sp->rxd[i].rfs);
- offset = (u32) &sp->rxd[i].frag_info - (u32) sp->rxd;
- netdev_info(dev, "%02x %04x frag_info = %016lx\n",
- i, offset, (unsigned long)sp->rxd[i].frag_info);
- }
-}
-
-static void ipg_dump_tfdlist(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int i;
- u32 offset;
-
- IPG_DEBUG_MSG("_dump_tfdlist\n");
-
- netdev_info(dev, "tx_current = %02x\n", sp->tx_current);
- netdev_info(dev, "tx_dirty = %02x\n", sp->tx_dirty);
- netdev_info(dev, "TFDList start address = %016lx\n",
- (unsigned long) sp->txd_map);
- netdev_info(dev, "TFDListPtr register = %08x%08x\n",
- ipg_r32(IPG_TFDLISTPTR1), ipg_r32(IPG_TFDLISTPTR0));
-
- for (i = 0; i < IPG_TFDLIST_LENGTH; i++) {
- offset = (u32) &sp->txd[i].next_desc - (u32) sp->txd;
- netdev_info(dev, "%02x %04x TFDNextPtr = %016lx\n",
- i, offset, (unsigned long)sp->txd[i].next_desc);
-
- offset = (u32) &sp->txd[i].tfc - (u32) sp->txd;
- netdev_info(dev, "%02x %04x TFC = %016lx\n",
- i, offset, (unsigned long) sp->txd[i].tfc);
- offset = (u32) &sp->txd[i].frag_info - (u32) sp->txd;
- netdev_info(dev, "%02x %04x frag_info = %016lx\n",
- i, offset, (unsigned long) sp->txd[i].frag_info);
- }
-}
-#endif
-
-static void ipg_write_phy_ctl(void __iomem *ioaddr, u8 data)
-{
- ipg_w8(IPG_PC_RSVD_MASK & data, PHY_CTRL);
- ndelay(IPG_PC_PHYCTRLWAIT_NS);
-}
-
-static void ipg_drive_phy_ctl_low_high(void __iomem *ioaddr, u8 data)
-{
- ipg_write_phy_ctl(ioaddr, IPG_PC_MGMTCLK_LO | data);
- ipg_write_phy_ctl(ioaddr, IPG_PC_MGMTCLK_HI | data);
-}
-
-static void send_three_state(void __iomem *ioaddr, u8 phyctrlpolarity)
-{
- phyctrlpolarity |= (IPG_PC_MGMTDATA & 0) | IPG_PC_MGMTDIR;
-
- ipg_drive_phy_ctl_low_high(ioaddr, phyctrlpolarity);
-}
-
-static void send_end(void __iomem *ioaddr, u8 phyctrlpolarity)
-{
- ipg_w8((IPG_PC_MGMTCLK_LO | (IPG_PC_MGMTDATA & 0) | IPG_PC_MGMTDIR |
- phyctrlpolarity) & IPG_PC_RSVD_MASK, PHY_CTRL);
-}
-
-static u16 read_phy_bit(void __iomem *ioaddr, u8 phyctrlpolarity)
-{
- u16 bit_data;
-
- ipg_write_phy_ctl(ioaddr, IPG_PC_MGMTCLK_LO | phyctrlpolarity);
-
- bit_data = ((ipg_r8(PHY_CTRL) & IPG_PC_MGMTDATA) >> 1) & 1;
-
- ipg_write_phy_ctl(ioaddr, IPG_PC_MGMTCLK_HI | phyctrlpolarity);
-
- return bit_data;
-}
-
-/*
- * Read a register from the Physical Layer device located
- * on the IPG NIC, using the IPG PHYCTRL register.
- */
-static int mdio_read(struct net_device *dev, int phy_id, int phy_reg)
-{
- void __iomem *ioaddr = ipg_ioaddr(dev);
- /*
- * The GMII mangement frame structure for a read is as follows:
- *
- * |Preamble|st|op|phyad|regad|ta| data |idle|
- * |< 32 1s>|01|10|AAAAA|RRRRR|z0|DDDDDDDDDDDDDDDD|z |
- *
- * <32 1s> = 32 consecutive logic 1 values
- * A = bit of Physical Layer device address (MSB first)
- * R = bit of register address (MSB first)
- * z = High impedance state
- * D = bit of read data (MSB first)
- *
- * Transmission order is 'Preamble' field first, bits transmitted
- * left to right (first to last).
- */
- struct {
- u32 field;
- unsigned int len;
- } p[] = {
- { GMII_PREAMBLE, 32 }, /* Preamble */
- { GMII_ST, 2 }, /* ST */
- { GMII_READ, 2 }, /* OP */
- { phy_id, 5 }, /* PHYAD */
- { phy_reg, 5 }, /* REGAD */
- { 0x0000, 2 }, /* TA */
- { 0x0000, 16 }, /* DATA */
- { 0x0000, 1 } /* IDLE */
- };
- unsigned int i, j;
- u8 polarity, data;
-
- polarity = ipg_r8(PHY_CTRL);
- polarity &= (IPG_PC_DUPLEX_POLARITY | IPG_PC_LINK_POLARITY);
-
- /* Create the Preamble, ST, OP, PHYAD, and REGAD field. */
- for (j = 0; j < 5; j++) {
- for (i = 0; i < p[j].len; i++) {
- /* For each variable length field, the MSB must be
- * transmitted first. Rotate through the field bits,
- * starting with the MSB, and move each bit into the
- * the 1st (2^1) bit position (this is the bit position
- * corresponding to the MgmtData bit of the PhyCtrl
- * register for the IPG).
- *
- * Example: ST = 01;
- *
- * First write a '0' to bit 1 of the PhyCtrl
- * register, then write a '1' to bit 1 of the
- * PhyCtrl register.
- *
- * To do this, right shift the MSB of ST by the value:
- * [field length - 1 - #ST bits already written]
- * then left shift this result by 1.
- */
- data = (p[j].field >> (p[j].len - 1 - i)) << 1;
- data &= IPG_PC_MGMTDATA;
- data |= polarity | IPG_PC_MGMTDIR;
-
- ipg_drive_phy_ctl_low_high(ioaddr, data);
- }
- }
-
- send_three_state(ioaddr, polarity);
-
- read_phy_bit(ioaddr, polarity);
-
- /*
- * For a read cycle, the bits for the next two fields (TA and
- * DATA) are driven by the PHY (the IPG reads these bits).
- */
- for (i = 0; i < p[6].len; i++) {
- p[6].field |=
- (read_phy_bit(ioaddr, polarity) << (p[6].len - 1 - i));
- }
-
- send_three_state(ioaddr, polarity);
- send_three_state(ioaddr, polarity);
- send_three_state(ioaddr, polarity);
- send_end(ioaddr, polarity);
-
- /* Return the value of the DATA field. */
- return p[6].field;
-}
-
-/*
- * Write to a register from the Physical Layer device located
- * on the IPG NIC, using the IPG PHYCTRL register.
- */
-static void mdio_write(struct net_device *dev, int phy_id, int phy_reg, int val)
-{
- void __iomem *ioaddr = ipg_ioaddr(dev);
- /*
- * The GMII mangement frame structure for a read is as follows:
- *
- * |Preamble|st|op|phyad|regad|ta| data |idle|
- * |< 32 1s>|01|10|AAAAA|RRRRR|z0|DDDDDDDDDDDDDDDD|z |
- *
- * <32 1s> = 32 consecutive logic 1 values
- * A = bit of Physical Layer device address (MSB first)
- * R = bit of register address (MSB first)
- * z = High impedance state
- * D = bit of write data (MSB first)
- *
- * Transmission order is 'Preamble' field first, bits transmitted
- * left to right (first to last).
- */
- struct {
- u32 field;
- unsigned int len;
- } p[] = {
- { GMII_PREAMBLE, 32 }, /* Preamble */
- { GMII_ST, 2 }, /* ST */
- { GMII_WRITE, 2 }, /* OP */
- { phy_id, 5 }, /* PHYAD */
- { phy_reg, 5 }, /* REGAD */
- { 0x0002, 2 }, /* TA */
- { val & 0xffff, 16 }, /* DATA */
- { 0x0000, 1 } /* IDLE */
- };
- unsigned int i, j;
- u8 polarity, data;
-
- polarity = ipg_r8(PHY_CTRL);
- polarity &= (IPG_PC_DUPLEX_POLARITY | IPG_PC_LINK_POLARITY);
-
- /* Create the Preamble, ST, OP, PHYAD, and REGAD field. */
- for (j = 0; j < 7; j++) {
- for (i = 0; i < p[j].len; i++) {
- /* For each variable length field, the MSB must be
- * transmitted first. Rotate through the field bits,
- * starting with the MSB, and move each bit into the
- * the 1st (2^1) bit position (this is the bit position
- * corresponding to the MgmtData bit of the PhyCtrl
- * register for the IPG).
- *
- * Example: ST = 01;
- *
- * First write a '0' to bit 1 of the PhyCtrl
- * register, then write a '1' to bit 1 of the
- * PhyCtrl register.
- *
- * To do this, right shift the MSB of ST by the value:
- * [field length - 1 - #ST bits already written]
- * then left shift this result by 1.
- */
- data = (p[j].field >> (p[j].len - 1 - i)) << 1;
- data &= IPG_PC_MGMTDATA;
- data |= polarity | IPG_PC_MGMTDIR;
-
- ipg_drive_phy_ctl_low_high(ioaddr, data);
- }
- }
-
- /* The last cycle is a tri-state, so read from the PHY. */
- ipg_write_phy_ctl(ioaddr, IPG_PC_MGMTCLK_LO | polarity);
- ipg_r8(PHY_CTRL);
- ipg_write_phy_ctl(ioaddr, IPG_PC_MGMTCLK_HI | polarity);
-}
-
-static void ipg_set_led_mode(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- u32 mode;
-
- mode = ipg_r32(ASIC_CTRL);
- mode &= ~(IPG_AC_LED_MODE_BIT_1 | IPG_AC_LED_MODE | IPG_AC_LED_SPEED);
-
- if ((sp->led_mode & 0x03) > 1)
- mode |= IPG_AC_LED_MODE_BIT_1; /* Write Asic Control Bit 29 */
-
- if ((sp->led_mode & 0x01) == 1)
- mode |= IPG_AC_LED_MODE; /* Write Asic Control Bit 14 */
-
- if ((sp->led_mode & 0x08) == 8)
- mode |= IPG_AC_LED_SPEED; /* Write Asic Control Bit 27 */
-
- ipg_w32(mode, ASIC_CTRL);
-}
-
-static void ipg_set_phy_set(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- int physet;
-
- physet = ipg_r8(PHY_SET);
- physet &= ~(IPG_PS_MEM_LENB9B | IPG_PS_MEM_LEN9 | IPG_PS_NON_COMPDET);
- physet |= ((sp->led_mode & 0x70) >> 4);
- ipg_w8(physet, PHY_SET);
-}
-
-static int ipg_reset(struct net_device *dev, u32 resetflags)
-{
- /* Assert functional resets via the IPG AsicCtrl
- * register as specified by the 'resetflags' input
- * parameter.
- */
- void __iomem *ioaddr = ipg_ioaddr(dev);
- unsigned int timeout_count = 0;
-
- IPG_DEBUG_MSG("_reset\n");
-
- ipg_w32(ipg_r32(ASIC_CTRL) | resetflags, ASIC_CTRL);
-
- /* Delay added to account for problem with 10Mbps reset. */
- mdelay(IPG_AC_RESETWAIT);
-
- while (IPG_AC_RESET_BUSY & ipg_r32(ASIC_CTRL)) {
- mdelay(IPG_AC_RESETWAIT);
- if (++timeout_count > IPG_AC_RESET_TIMEOUT)
- return -ETIME;
- }
- /* Set LED Mode in Asic Control */
- ipg_set_led_mode(dev);
-
- /* Set PHYSet Register Value */
- ipg_set_phy_set(dev);
- return 0;
-}
-
-/* Find the GMII PHY address. */
-static int ipg_find_phyaddr(struct net_device *dev)
-{
- unsigned int phyaddr, i;
-
- for (i = 0; i < 32; i++) {
- u32 status;
-
- /* Search for the correct PHY address among 32 possible. */
- phyaddr = (IPG_NIC_PHY_ADDRESS + i) % 32;
-
- /* 10/22/03 Grace change verify from GMII_PHY_STATUS to
- GMII_PHY_ID1
- */
-
- status = mdio_read(dev, phyaddr, MII_BMSR);
-
- if ((status != 0xFFFF) && (status != 0))
- return phyaddr;
- }
-
- return 0x1f;
-}
-
-/*
- * Configure IPG based on result of IEEE 802.3 PHY
- * auto-negotiation.
- */
-static int ipg_config_autoneg(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int txflowcontrol;
- unsigned int rxflowcontrol;
- unsigned int fullduplex;
- u32 mac_ctrl_val;
- u32 asicctrl;
- u8 phyctrl;
- const char *speed;
- const char *duplex;
- const char *tx_desc;
- const char *rx_desc;
-
- IPG_DEBUG_MSG("_config_autoneg\n");
-
- asicctrl = ipg_r32(ASIC_CTRL);
- phyctrl = ipg_r8(PHY_CTRL);
- mac_ctrl_val = ipg_r32(MAC_CTRL);
-
- /* Set flags for use in resolving auto-negotiation, assuming
- * non-1000Mbps, half duplex, no flow control.
- */
- fullduplex = 0;
- txflowcontrol = 0;
- rxflowcontrol = 0;
-
- /* To accommodate a problem in 10Mbps operation,
- * set a global flag if PHY running in 10Mbps mode.
- */
- sp->tenmbpsmode = 0;
-
- /* Determine actual speed of operation. */
- switch (phyctrl & IPG_PC_LINK_SPEED) {
- case IPG_PC_LINK_SPEED_10MBPS:
- speed = "10Mbps";
- sp->tenmbpsmode = 1;
- break;
- case IPG_PC_LINK_SPEED_100MBPS:
- speed = "100Mbps";
- break;
- case IPG_PC_LINK_SPEED_1000MBPS:
- speed = "1000Mbps";
- break;
- default:
- speed = "undefined!";
- return 0;
- }
-
- netdev_info(dev, "Link speed = %s\n", speed);
- if (sp->tenmbpsmode == 1)
- netdev_info(dev, "10Mbps operational mode enabled\n");
-
- if (phyctrl & IPG_PC_DUPLEX_STATUS) {
- fullduplex = 1;
- txflowcontrol = 1;
- rxflowcontrol = 1;
- }
-
- /* Configure full duplex, and flow control. */
- if (fullduplex == 1) {
-
- /* Configure IPG for full duplex operation. */
-
- duplex = "full";
-
- mac_ctrl_val |= IPG_MC_DUPLEX_SELECT_FD;
-
- if (txflowcontrol == 1) {
- tx_desc = "";
- mac_ctrl_val |= IPG_MC_TX_FLOW_CONTROL_ENABLE;
- } else {
- tx_desc = "no ";
- mac_ctrl_val &= ~IPG_MC_TX_FLOW_CONTROL_ENABLE;
- }
-
- if (rxflowcontrol == 1) {
- rx_desc = "";
- mac_ctrl_val |= IPG_MC_RX_FLOW_CONTROL_ENABLE;
- } else {
- rx_desc = "no ";
- mac_ctrl_val &= ~IPG_MC_RX_FLOW_CONTROL_ENABLE;
- }
- } else {
- duplex = "half";
- tx_desc = "no ";
- rx_desc = "no ";
- mac_ctrl_val &= (~IPG_MC_DUPLEX_SELECT_FD &
- ~IPG_MC_TX_FLOW_CONTROL_ENABLE &
- ~IPG_MC_RX_FLOW_CONTROL_ENABLE);
- }
-
- netdev_info(dev, "setting %s duplex, %sTX, %sRX flow control\n",
- duplex, tx_desc, rx_desc);
- ipg_w32(mac_ctrl_val, MAC_CTRL);
-
- return 0;
-}
-
-/* Determine and configure multicast operation and set
- * receive mode for IPG.
- */
-static void ipg_nic_set_multicast_list(struct net_device *dev)
-{
- void __iomem *ioaddr = ipg_ioaddr(dev);
- struct netdev_hw_addr *ha;
- unsigned int hashindex;
- u32 hashtable[2];
- u8 receivemode;
-
- IPG_DEBUG_MSG("_nic_set_multicast_list\n");
-
- receivemode = IPG_RM_RECEIVEUNICAST | IPG_RM_RECEIVEBROADCAST;
-
- if (dev->flags & IFF_PROMISC) {
- /* NIC to be configured in promiscuous mode. */
- receivemode = IPG_RM_RECEIVEALLFRAMES;
- } else if ((dev->flags & IFF_ALLMULTI) ||
- ((dev->flags & IFF_MULTICAST) &&
- (netdev_mc_count(dev) > IPG_MULTICAST_HASHTABLE_SIZE))) {
- /* NIC to be configured to receive all multicast
- * frames. */
- receivemode |= IPG_RM_RECEIVEMULTICAST;
- } else if ((dev->flags & IFF_MULTICAST) && !netdev_mc_empty(dev)) {
- /* NIC to be configured to receive selected
- * multicast addresses. */
- receivemode |= IPG_RM_RECEIVEMULTICASTHASH;
- }
-
- /* Calculate the bits to set for the 64 bit, IPG HASHTABLE.
- * The IPG applies a cyclic-redundancy-check (the same CRC
- * used to calculate the frame data FCS) to the destination
- * address all incoming multicast frames whose destination
- * address has the multicast bit set. The least significant
- * 6 bits of the CRC result are used as an addressing index
- * into the hash table. If the value of the bit addressed by
- * this index is a 1, the frame is passed to the host system.
- */
-
- /* Clear hashtable. */
- hashtable[0] = 0x00000000;
- hashtable[1] = 0x00000000;
-
- /* Cycle through all multicast addresses to filter. */
- netdev_for_each_mc_addr(ha, dev) {
- /* Calculate CRC result for each multicast address. */
- hashindex = crc32_le(0xffffffff, ha->addr,
- ETH_ALEN);
-
- /* Use only the least significant 6 bits. */
- hashindex = hashindex & 0x3F;
-
- /* Within "hashtable", set bit number "hashindex"
- * to a logic 1.
- */
- set_bit(hashindex, (void *)hashtable);
- }
-
- /* Write the value of the hashtable, to the 4, 16 bit
- * HASHTABLE IPG registers.
- */
- ipg_w32(hashtable[0], HASHTABLE_0);
- ipg_w32(hashtable[1], HASHTABLE_1);
-
- ipg_w8(IPG_RM_RSVD_MASK & receivemode, RECEIVE_MODE);
-
- IPG_DEBUG_MSG("ReceiveMode = %x\n", ipg_r8(RECEIVE_MODE));
-}
-
-static int ipg_io_config(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = ipg_ioaddr(dev);
- u32 origmacctrl;
- u32 restoremacctrl;
-
- IPG_DEBUG_MSG("_io_config\n");
-
- origmacctrl = ipg_r32(MAC_CTRL);
-
- restoremacctrl = origmacctrl | IPG_MC_STATISTICS_ENABLE;
-
- /* Based on compilation option, determine if FCS is to be
- * stripped on receive frames by IPG.
- */
- if (!IPG_STRIP_FCS_ON_RX)
- restoremacctrl |= IPG_MC_RCV_FCS;
-
- /* Determine if transmitter and/or receiver are
- * enabled so we may restore MACCTRL correctly.
- */
- if (origmacctrl & IPG_MC_TX_ENABLED)
- restoremacctrl |= IPG_MC_TX_ENABLE;
-
- if (origmacctrl & IPG_MC_RX_ENABLED)
- restoremacctrl |= IPG_MC_RX_ENABLE;
-
- /* Transmitter and receiver must be disabled before setting
- * IFSSelect.
- */
- ipg_w32((origmacctrl & (IPG_MC_RX_DISABLE | IPG_MC_TX_DISABLE)) &
- IPG_MC_RSVD_MASK, MAC_CTRL);
-
- /* Now that transmitter and receiver are disabled, write
- * to IFSSelect.
- */
- ipg_w32((origmacctrl & IPG_MC_IFS_96BIT) & IPG_MC_RSVD_MASK, MAC_CTRL);
-
- /* Set RECEIVEMODE register. */
- ipg_nic_set_multicast_list(dev);
-
- ipg_w16(sp->max_rxframe_size, MAX_FRAME_SIZE);
-
- ipg_w8(IPG_RXDMAPOLLPERIOD_VALUE, RX_DMA_POLL_PERIOD);
- ipg_w8(IPG_RXDMAURGENTTHRESH_VALUE, RX_DMA_URGENT_THRESH);
- ipg_w8(IPG_RXDMABURSTTHRESH_VALUE, RX_DMA_BURST_THRESH);
- ipg_w8(IPG_TXDMAPOLLPERIOD_VALUE, TX_DMA_POLL_PERIOD);
- ipg_w8(IPG_TXDMAURGENTTHRESH_VALUE, TX_DMA_URGENT_THRESH);
- ipg_w8(IPG_TXDMABURSTTHRESH_VALUE, TX_DMA_BURST_THRESH);
- ipg_w16((IPG_IE_HOST_ERROR | IPG_IE_TX_DMA_COMPLETE |
- IPG_IE_TX_COMPLETE | IPG_IE_INT_REQUESTED |
- IPG_IE_UPDATE_STATS | IPG_IE_LINK_EVENT |
- IPG_IE_RX_DMA_COMPLETE | IPG_IE_RX_DMA_PRIORITY), INT_ENABLE);
- ipg_w16(IPG_FLOWONTHRESH_VALUE, FLOW_ON_THRESH);
- ipg_w16(IPG_FLOWOFFTHRESH_VALUE, FLOW_OFF_THRESH);
-
- /* IPG multi-frag frame bug workaround.
- * Per silicon revision B3 eratta.
- */
- ipg_w16(ipg_r16(DEBUG_CTRL) | 0x0200, DEBUG_CTRL);
-
- /* IPG TX poll now bug workaround.
- * Per silicon revision B3 eratta.
- */
- ipg_w16(ipg_r16(DEBUG_CTRL) | 0x0010, DEBUG_CTRL);
-
- /* IPG RX poll now bug workaround.
- * Per silicon revision B3 eratta.
- */
- ipg_w16(ipg_r16(DEBUG_CTRL) | 0x0020, DEBUG_CTRL);
-
- /* Now restore MACCTRL to original setting. */
- ipg_w32(IPG_MC_RSVD_MASK & restoremacctrl, MAC_CTRL);
-
- /* Disable unused RMON statistics. */
- ipg_w32(IPG_RZ_ALL, RMON_STATISTICS_MASK);
-
- /* Disable unused MIB statistics. */
- ipg_w32(IPG_SM_MACCONTROLFRAMESXMTD | IPG_SM_MACCONTROLFRAMESRCVD |
- IPG_SM_BCSTOCTETXMTOK_BCSTFRAMESXMTDOK | IPG_SM_TXJUMBOFRAMES |
- IPG_SM_MCSTOCTETXMTOK_MCSTFRAMESXMTDOK | IPG_SM_RXJUMBOFRAMES |
- IPG_SM_BCSTOCTETRCVDOK_BCSTFRAMESRCVDOK |
- IPG_SM_UDPCHECKSUMERRORS | IPG_SM_TCPCHECKSUMERRORS |
- IPG_SM_IPCHECKSUMERRORS, STATISTICS_MASK);
-
- return 0;
-}
-
-/*
- * Create a receive buffer within system memory and update
- * NIC private structure appropriately.
- */
-static int ipg_get_rxbuff(struct net_device *dev, int entry)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- struct ipg_rx *rxfd = sp->rxd + entry;
- struct sk_buff *skb;
- u64 rxfragsize;
-
- IPG_DEBUG_MSG("_get_rxbuff\n");
-
- skb = netdev_alloc_skb_ip_align(dev, sp->rxsupport_size);
- if (!skb) {
- sp->rx_buff[entry] = NULL;
- return -ENOMEM;
- }
-
- /* Save the address of the sk_buff structure. */
- sp->rx_buff[entry] = skb;
-
- rxfd->frag_info = cpu_to_le64(pci_map_single(sp->pdev, skb->data,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE));
-
- /* Set the RFD fragment length. */
- rxfragsize = sp->rxfrag_size;
- rxfd->frag_info |= cpu_to_le64((rxfragsize << 48) & IPG_RFI_FRAGLEN);
-
- return 0;
-}
-
-static int init_rfdlist(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int i;
-
- IPG_DEBUG_MSG("_init_rfdlist\n");
-
- for (i = 0; i < IPG_RFDLIST_LENGTH; i++) {
- struct ipg_rx *rxfd = sp->rxd + i;
-
- if (sp->rx_buff[i]) {
- pci_unmap_single(sp->pdev,
- le64_to_cpu(rxfd->frag_info) & ~IPG_RFI_FRAGLEN,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE);
- dev_kfree_skb_irq(sp->rx_buff[i]);
- sp->rx_buff[i] = NULL;
- }
-
- /* Clear out the RFS field. */
- rxfd->rfs = 0x0000000000000000;
-
- if (ipg_get_rxbuff(dev, i) < 0) {
- /*
- * A receive buffer was not ready, break the
- * RFD list here.
- */
- IPG_DEBUG_MSG("Cannot allocate Rx buffer\n");
-
- /* Just in case we cannot allocate a single RFD.
- * Should not occur.
- */
- if (i == 0) {
- netdev_err(dev, "No memory available for RFD list\n");
- return -ENOMEM;
- }
- }
-
- rxfd->next_desc = cpu_to_le64(sp->rxd_map +
- sizeof(struct ipg_rx)*(i + 1));
- }
- sp->rxd[i - 1].next_desc = cpu_to_le64(sp->rxd_map);
-
- sp->rx_current = 0;
- sp->rx_dirty = 0;
-
- /* Write the location of the RFDList to the IPG. */
- ipg_w32((u32) sp->rxd_map, RFD_LIST_PTR_0);
- ipg_w32(0x00000000, RFD_LIST_PTR_1);
-
- return 0;
-}
-
-static void init_tfdlist(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int i;
-
- IPG_DEBUG_MSG("_init_tfdlist\n");
-
- for (i = 0; i < IPG_TFDLIST_LENGTH; i++) {
- struct ipg_tx *txfd = sp->txd + i;
-
- txfd->tfc = cpu_to_le64(IPG_TFC_TFDDONE);
-
- if (sp->tx_buff[i]) {
- dev_kfree_skb_irq(sp->tx_buff[i]);
- sp->tx_buff[i] = NULL;
- }
-
- txfd->next_desc = cpu_to_le64(sp->txd_map +
- sizeof(struct ipg_tx)*(i + 1));
- }
- sp->txd[i - 1].next_desc = cpu_to_le64(sp->txd_map);
-
- sp->tx_current = 0;
- sp->tx_dirty = 0;
-
- /* Write the location of the TFDList to the IPG. */
- IPG_DDEBUG_MSG("Starting TFDListPtr = %08x\n",
- (u32) sp->txd_map);
- ipg_w32((u32) sp->txd_map, TFD_LIST_PTR_0);
- ipg_w32(0x00000000, TFD_LIST_PTR_1);
-
- sp->reset_current_tfd = 1;
-}
-
-/*
- * Free all transmit buffers which have already been transferred
- * via DMA to the IPG.
- */
-static void ipg_nic_txfree(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- unsigned int released, pending, dirty;
-
- IPG_DEBUG_MSG("_nic_txfree\n");
-
- pending = sp->tx_current - sp->tx_dirty;
- dirty = sp->tx_dirty % IPG_TFDLIST_LENGTH;
-
- for (released = 0; released < pending; released++) {
- struct sk_buff *skb = sp->tx_buff[dirty];
- struct ipg_tx *txfd = sp->txd + dirty;
-
- IPG_DEBUG_MSG("TFC = %016lx\n", (unsigned long) txfd->tfc);
-
- /* Look at each TFD's TFC field beginning
- * at the last freed TFD up to the current TFD.
- * If the TFDDone bit is set, free the associated
- * buffer.
- */
- if (!(txfd->tfc & cpu_to_le64(IPG_TFC_TFDDONE)))
- break;
-
- /* Free the transmit buffer. */
- if (skb) {
- pci_unmap_single(sp->pdev,
- le64_to_cpu(txfd->frag_info) & ~IPG_TFI_FRAGLEN,
- skb->len, PCI_DMA_TODEVICE);
-
- dev_kfree_skb_irq(skb);
-
- sp->tx_buff[dirty] = NULL;
- }
- dirty = (dirty + 1) % IPG_TFDLIST_LENGTH;
- }
-
- sp->tx_dirty += released;
-
- if (netif_queue_stopped(dev) &&
- (sp->tx_current != (sp->tx_dirty + IPG_TFDLIST_LENGTH))) {
- netif_wake_queue(dev);
- }
-}
-
-static void ipg_tx_timeout(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
-
- ipg_reset(dev, IPG_AC_TX_RESET | IPG_AC_DMA | IPG_AC_NETWORK |
- IPG_AC_FIFO);
-
- spin_lock_irq(&sp->lock);
-
- /* Re-configure after DMA reset. */
- if (ipg_io_config(dev) < 0)
- netdev_info(dev, "Error during re-configuration\n");
-
- init_tfdlist(dev);
-
- spin_unlock_irq(&sp->lock);
-
- ipg_w32((ipg_r32(MAC_CTRL) | IPG_MC_TX_ENABLE) & IPG_MC_RSVD_MASK,
- MAC_CTRL);
-}
-
-/*
- * For TxComplete interrupts, free all transmit
- * buffers which have already been transferred via DMA
- * to the IPG.
- */
-static void ipg_nic_txcleanup(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int i;
-
- IPG_DEBUG_MSG("_nic_txcleanup\n");
-
- for (i = 0; i < IPG_TFDLIST_LENGTH; i++) {
- /* Reading the TXSTATUS register clears the
- * TX_COMPLETE interrupt.
- */
- u32 txstatusdword = ipg_r32(TX_STATUS);
-
- IPG_DEBUG_MSG("TxStatus = %08x\n", txstatusdword);
-
- /* Check for Transmit errors. Error bits only valid if
- * TX_COMPLETE bit in the TXSTATUS register is a 1.
- */
- if (!(txstatusdword & IPG_TS_TX_COMPLETE))
- break;
-
- /* If in 10Mbps mode, indicate transmit is ready. */
- if (sp->tenmbpsmode) {
- netif_wake_queue(dev);
- }
-
- /* Transmit error, increment stat counters. */
- if (txstatusdword & IPG_TS_TX_ERROR) {
- IPG_DEBUG_MSG("Transmit error\n");
- sp->stats.tx_errors++;
- }
-
- /* Late collision, re-enable transmitter. */
- if (txstatusdword & IPG_TS_LATE_COLLISION) {
- IPG_DEBUG_MSG("Late collision on transmit\n");
- ipg_w32((ipg_r32(MAC_CTRL) | IPG_MC_TX_ENABLE) &
- IPG_MC_RSVD_MASK, MAC_CTRL);
- }
-
- /* Maximum collisions, re-enable transmitter. */
- if (txstatusdword & IPG_TS_TX_MAX_COLL) {
- IPG_DEBUG_MSG("Maximum collisions on transmit\n");
- ipg_w32((ipg_r32(MAC_CTRL) | IPG_MC_TX_ENABLE) &
- IPG_MC_RSVD_MASK, MAC_CTRL);
- }
-
- /* Transmit underrun, reset and re-enable
- * transmitter.
- */
- if (txstatusdword & IPG_TS_TX_UNDERRUN) {
- IPG_DEBUG_MSG("Transmitter underrun\n");
- sp->stats.tx_fifo_errors++;
- ipg_reset(dev, IPG_AC_TX_RESET | IPG_AC_DMA |
- IPG_AC_NETWORK | IPG_AC_FIFO);
-
- /* Re-configure after DMA reset. */
- if (ipg_io_config(dev) < 0) {
- netdev_info(dev, "Error during re-configuration\n");
- }
- init_tfdlist(dev);
-
- ipg_w32((ipg_r32(MAC_CTRL) | IPG_MC_TX_ENABLE) &
- IPG_MC_RSVD_MASK, MAC_CTRL);
- }
- }
-
- ipg_nic_txfree(dev);
-}
-
-/* Provides statistical information about the IPG NIC. */
-static struct net_device_stats *ipg_nic_get_stats(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- u16 temp1;
- u16 temp2;
-
- IPG_DEBUG_MSG("_nic_get_stats\n");
-
- /* Check to see if the NIC has been initialized via nic_open,
- * before trying to read statistic registers.
- */
- if (!netif_running(dev))
- return &sp->stats;
-
- sp->stats.rx_packets += ipg_r32(IPG_FRAMESRCVDOK);
- sp->stats.tx_packets += ipg_r32(IPG_FRAMESXMTDOK);
- sp->stats.rx_bytes += ipg_r32(IPG_OCTETRCVOK);
- sp->stats.tx_bytes += ipg_r32(IPG_OCTETXMTOK);
- temp1 = ipg_r16(IPG_FRAMESLOSTRXERRORS);
- sp->stats.rx_errors += temp1;
- sp->stats.rx_missed_errors += temp1;
- temp1 = ipg_r32(IPG_SINGLECOLFRAMES) + ipg_r32(IPG_MULTICOLFRAMES) +
- ipg_r32(IPG_LATECOLLISIONS);
- temp2 = ipg_r16(IPG_CARRIERSENSEERRORS);
- sp->stats.collisions += temp1;
- sp->stats.tx_dropped += ipg_r16(IPG_FRAMESABORTXSCOLLS);
- sp->stats.tx_errors += ipg_r16(IPG_FRAMESWEXDEFERRAL) +
- ipg_r32(IPG_FRAMESWDEFERREDXMT) + temp1 + temp2;
- sp->stats.multicast += ipg_r32(IPG_MCSTOCTETRCVDOK);
-
- /* detailed tx_errors */
- sp->stats.tx_carrier_errors += temp2;
-
- /* detailed rx_errors */
- sp->stats.rx_length_errors += ipg_r16(IPG_INRANGELENGTHERRORS) +
- ipg_r16(IPG_FRAMETOOLONGERRORS);
- sp->stats.rx_crc_errors += ipg_r16(IPG_FRAMECHECKSEQERRORS);
-
- /* Unutilized IPG statistic registers. */
- ipg_r32(IPG_MCSTFRAMESRCVDOK);
-
- return &sp->stats;
-}
-
-/* Restore used receive buffers. */
-static int ipg_nic_rxrestore(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- const unsigned int curr = sp->rx_current;
- unsigned int dirty = sp->rx_dirty;
-
- IPG_DEBUG_MSG("_nic_rxrestore\n");
-
- for (dirty = sp->rx_dirty; curr - dirty > 0; dirty++) {
- unsigned int entry = dirty % IPG_RFDLIST_LENGTH;
-
- /* rx_copybreak may poke hole here and there. */
- if (sp->rx_buff[entry])
- continue;
-
- /* Generate a new receive buffer to replace the
- * current buffer (which will be released by the
- * Linux system).
- */
- if (ipg_get_rxbuff(dev, entry) < 0) {
- IPG_DEBUG_MSG("Cannot allocate new Rx buffer\n");
-
- break;
- }
-
- /* Reset the RFS field. */
- sp->rxd[entry].rfs = 0x0000000000000000;
- }
- sp->rx_dirty = dirty;
-
- return 0;
-}
-
-/* use jumboindex and jumbosize to control jumbo frame status
- * initial status is jumboindex=-1 and jumbosize=0
- * 1. jumboindex = -1 and jumbosize=0 : previous jumbo frame has been done.
- * 2. jumboindex != -1 and jumbosize != 0 : jumbo frame is not over size and receiving
- * 3. jumboindex = -1 and jumbosize != 0 : jumbo frame is over size, already dump
- * previous receiving and need to continue dumping the current one
- */
-enum {
- NORMAL_PACKET,
- ERROR_PACKET
-};
-
-enum {
- FRAME_NO_START_NO_END = 0,
- FRAME_WITH_START = 1,
- FRAME_WITH_END = 10,
- FRAME_WITH_START_WITH_END = 11
-};
-
-static void ipg_nic_rx_free_skb(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- unsigned int entry = sp->rx_current % IPG_RFDLIST_LENGTH;
-
- if (sp->rx_buff[entry]) {
- struct ipg_rx *rxfd = sp->rxd + entry;
-
- pci_unmap_single(sp->pdev,
- le64_to_cpu(rxfd->frag_info) & ~IPG_RFI_FRAGLEN,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE);
- dev_kfree_skb_irq(sp->rx_buff[entry]);
- sp->rx_buff[entry] = NULL;
- }
-}
-
-static int ipg_nic_rx_check_frame_type(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- struct ipg_rx *rxfd = sp->rxd + (sp->rx_current % IPG_RFDLIST_LENGTH);
- int type = FRAME_NO_START_NO_END;
-
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_FRAMESTART)
- type += FRAME_WITH_START;
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_FRAMEEND)
- type += FRAME_WITH_END;
- return type;
-}
-
-static int ipg_nic_rx_check_error(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- unsigned int entry = sp->rx_current % IPG_RFDLIST_LENGTH;
- struct ipg_rx *rxfd = sp->rxd + entry;
-
- if (IPG_DROP_ON_RX_ETH_ERRORS && (le64_to_cpu(rxfd->rfs) &
- (IPG_RFS_RXFIFOOVERRUN | IPG_RFS_RXRUNTFRAME |
- IPG_RFS_RXALIGNMENTERROR | IPG_RFS_RXFCSERROR |
- IPG_RFS_RXOVERSIZEDFRAME | IPG_RFS_RXLENGTHERROR))) {
- IPG_DEBUG_MSG("Rx error, RFS = %016lx\n",
- (unsigned long) rxfd->rfs);
-
- /* Increment general receive error statistic. */
- sp->stats.rx_errors++;
-
- /* Increment detailed receive error statistics. */
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXFIFOOVERRUN) {
- IPG_DEBUG_MSG("RX FIFO overrun occurred\n");
-
- sp->stats.rx_fifo_errors++;
- }
-
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXRUNTFRAME) {
- IPG_DEBUG_MSG("RX runt occurred\n");
- sp->stats.rx_length_errors++;
- }
-
- /* Do nothing for IPG_RFS_RXOVERSIZEDFRAME,
- * error count handled by a IPG statistic register.
- */
-
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXALIGNMENTERROR) {
- IPG_DEBUG_MSG("RX alignment error occurred\n");
- sp->stats.rx_frame_errors++;
- }
-
- /* Do nothing for IPG_RFS_RXFCSERROR, error count
- * handled by a IPG statistic register.
- */
-
- /* Free the memory associated with the RX
- * buffer since it is erroneous and we will
- * not pass it to higher layer processes.
- */
- if (sp->rx_buff[entry]) {
- pci_unmap_single(sp->pdev,
- le64_to_cpu(rxfd->frag_info) & ~IPG_RFI_FRAGLEN,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE);
-
- dev_kfree_skb_irq(sp->rx_buff[entry]);
- sp->rx_buff[entry] = NULL;
- }
- return ERROR_PACKET;
- }
- return NORMAL_PACKET;
-}
-
-static void ipg_nic_rx_with_start_and_end(struct net_device *dev,
- struct ipg_nic_private *sp,
- struct ipg_rx *rxfd, unsigned entry)
-{
- struct ipg_jumbo *jumbo = &sp->jumbo;
- struct sk_buff *skb;
- int framelen;
-
- if (jumbo->found_start) {
- dev_kfree_skb_irq(jumbo->skb);
- jumbo->found_start = 0;
- jumbo->current_size = 0;
- jumbo->skb = NULL;
- }
-
- /* 1: found error, 0 no error */
- if (ipg_nic_rx_check_error(dev) != NORMAL_PACKET)
- return;
-
- skb = sp->rx_buff[entry];
- if (!skb)
- return;
-
- /* accept this frame and send to upper layer */
- framelen = le64_to_cpu(rxfd->rfs) & IPG_RFS_RXFRAMELEN;
- if (framelen > sp->rxfrag_size)
- framelen = sp->rxfrag_size;
-
- skb_put(skb, framelen);
- skb->protocol = eth_type_trans(skb, dev);
- skb_checksum_none_assert(skb);
- netif_rx(skb);
- sp->rx_buff[entry] = NULL;
-}
-
-static void ipg_nic_rx_with_start(struct net_device *dev,
- struct ipg_nic_private *sp,
- struct ipg_rx *rxfd, unsigned entry)
-{
- struct ipg_jumbo *jumbo = &sp->jumbo;
- struct pci_dev *pdev = sp->pdev;
- struct sk_buff *skb;
-
- /* 1: found error, 0 no error */
- if (ipg_nic_rx_check_error(dev) != NORMAL_PACKET)
- return;
-
- /* accept this frame and send to upper layer */
- skb = sp->rx_buff[entry];
- if (!skb)
- return;
-
- if (jumbo->found_start)
- dev_kfree_skb_irq(jumbo->skb);
-
- pci_unmap_single(pdev, le64_to_cpu(rxfd->frag_info) & ~IPG_RFI_FRAGLEN,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE);
-
- skb_put(skb, sp->rxfrag_size);
-
- jumbo->found_start = 1;
- jumbo->current_size = sp->rxfrag_size;
- jumbo->skb = skb;
-
- sp->rx_buff[entry] = NULL;
-}
-
-static void ipg_nic_rx_with_end(struct net_device *dev,
- struct ipg_nic_private *sp,
- struct ipg_rx *rxfd, unsigned entry)
-{
- struct ipg_jumbo *jumbo = &sp->jumbo;
-
- /* 1: found error, 0 no error */
- if (ipg_nic_rx_check_error(dev) == NORMAL_PACKET) {
- struct sk_buff *skb = sp->rx_buff[entry];
-
- if (!skb)
- return;
-
- if (jumbo->found_start) {
- int framelen, endframelen;
-
- framelen = le64_to_cpu(rxfd->rfs) & IPG_RFS_RXFRAMELEN;
-
- endframelen = framelen - jumbo->current_size;
- if (framelen > sp->rxsupport_size)
- dev_kfree_skb_irq(jumbo->skb);
- else {
- memcpy(skb_put(jumbo->skb, endframelen),
- skb->data, endframelen);
-
- jumbo->skb->protocol =
- eth_type_trans(jumbo->skb, dev);
-
- skb_checksum_none_assert(jumbo->skb);
- netif_rx(jumbo->skb);
- }
- }
-
- jumbo->found_start = 0;
- jumbo->current_size = 0;
- jumbo->skb = NULL;
-
- ipg_nic_rx_free_skb(dev);
- } else {
- dev_kfree_skb_irq(jumbo->skb);
- jumbo->found_start = 0;
- jumbo->current_size = 0;
- jumbo->skb = NULL;
- }
-}
-
-static void ipg_nic_rx_no_start_no_end(struct net_device *dev,
- struct ipg_nic_private *sp,
- struct ipg_rx *rxfd, unsigned entry)
-{
- struct ipg_jumbo *jumbo = &sp->jumbo;
-
- /* 1: found error, 0 no error */
- if (ipg_nic_rx_check_error(dev) == NORMAL_PACKET) {
- struct sk_buff *skb = sp->rx_buff[entry];
-
- if (skb) {
- if (jumbo->found_start) {
- jumbo->current_size += sp->rxfrag_size;
- if (jumbo->current_size <= sp->rxsupport_size) {
- memcpy(skb_put(jumbo->skb,
- sp->rxfrag_size),
- skb->data, sp->rxfrag_size);
- }
- }
- ipg_nic_rx_free_skb(dev);
- }
- } else {
- dev_kfree_skb_irq(jumbo->skb);
- jumbo->found_start = 0;
- jumbo->current_size = 0;
- jumbo->skb = NULL;
- }
-}
-
-static int ipg_nic_rx_jumbo(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- unsigned int curr = sp->rx_current;
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int i;
-
- IPG_DEBUG_MSG("_nic_rx\n");
-
- for (i = 0; i < IPG_MAXRFDPROCESS_COUNT; i++, curr++) {
- unsigned int entry = curr % IPG_RFDLIST_LENGTH;
- struct ipg_rx *rxfd = sp->rxd + entry;
-
- if (!(rxfd->rfs & cpu_to_le64(IPG_RFS_RFDDONE)))
- break;
-
- switch (ipg_nic_rx_check_frame_type(dev)) {
- case FRAME_WITH_START_WITH_END:
- ipg_nic_rx_with_start_and_end(dev, sp, rxfd, entry);
- break;
- case FRAME_WITH_START:
- ipg_nic_rx_with_start(dev, sp, rxfd, entry);
- break;
- case FRAME_WITH_END:
- ipg_nic_rx_with_end(dev, sp, rxfd, entry);
- break;
- case FRAME_NO_START_NO_END:
- ipg_nic_rx_no_start_no_end(dev, sp, rxfd, entry);
- break;
- }
- }
-
- sp->rx_current = curr;
-
- if (i == IPG_MAXRFDPROCESS_COUNT) {
- /* There are more RFDs to process, however the
- * allocated amount of RFD processing time has
- * expired. Assert Interrupt Requested to make
- * sure we come back to process the remaining RFDs.
- */
- ipg_w32(ipg_r32(ASIC_CTRL) | IPG_AC_INT_REQUEST, ASIC_CTRL);
- }
-
- ipg_nic_rxrestore(dev);
-
- return 0;
-}
-
-static int ipg_nic_rx(struct net_device *dev)
-{
- /* Transfer received Ethernet frames to higher network layers. */
- struct ipg_nic_private *sp = netdev_priv(dev);
- unsigned int curr = sp->rx_current;
- void __iomem *ioaddr = sp->ioaddr;
- struct ipg_rx *rxfd;
- unsigned int i;
-
- IPG_DEBUG_MSG("_nic_rx\n");
-
-#define __RFS_MASK \
- cpu_to_le64(IPG_RFS_RFDDONE | IPG_RFS_FRAMESTART | IPG_RFS_FRAMEEND)
-
- for (i = 0; i < IPG_MAXRFDPROCESS_COUNT; i++, curr++) {
- unsigned int entry = curr % IPG_RFDLIST_LENGTH;
- struct sk_buff *skb = sp->rx_buff[entry];
- unsigned int framelen;
-
- rxfd = sp->rxd + entry;
-
- if (((rxfd->rfs & __RFS_MASK) != __RFS_MASK) || !skb)
- break;
-
- /* Get received frame length. */
- framelen = le64_to_cpu(rxfd->rfs) & IPG_RFS_RXFRAMELEN;
-
- /* Check for jumbo frame arrival with too small
- * RXFRAG_SIZE.
- */
- if (framelen > sp->rxfrag_size) {
- IPG_DEBUG_MSG
- ("RFS FrameLen > allocated fragment size\n");
-
- framelen = sp->rxfrag_size;
- }
-
- if ((IPG_DROP_ON_RX_ETH_ERRORS && (le64_to_cpu(rxfd->rfs) &
- (IPG_RFS_RXFIFOOVERRUN | IPG_RFS_RXRUNTFRAME |
- IPG_RFS_RXALIGNMENTERROR | IPG_RFS_RXFCSERROR |
- IPG_RFS_RXOVERSIZEDFRAME | IPG_RFS_RXLENGTHERROR)))) {
-
- IPG_DEBUG_MSG("Rx error, RFS = %016lx\n",
- (unsigned long int) rxfd->rfs);
-
- /* Increment general receive error statistic. */
- sp->stats.rx_errors++;
-
- /* Increment detailed receive error statistics. */
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXFIFOOVERRUN) {
- IPG_DEBUG_MSG("RX FIFO overrun occurred\n");
- sp->stats.rx_fifo_errors++;
- }
-
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXRUNTFRAME) {
- IPG_DEBUG_MSG("RX runt occurred\n");
- sp->stats.rx_length_errors++;
- }
-
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXOVERSIZEDFRAME) ;
- /* Do nothing, error count handled by a IPG
- * statistic register.
- */
-
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXALIGNMENTERROR) {
- IPG_DEBUG_MSG("RX alignment error occurred\n");
- sp->stats.rx_frame_errors++;
- }
-
- if (le64_to_cpu(rxfd->rfs) & IPG_RFS_RXFCSERROR) ;
- /* Do nothing, error count handled by a IPG
- * statistic register.
- */
-
- /* Free the memory associated with the RX
- * buffer since it is erroneous and we will
- * not pass it to higher layer processes.
- */
- if (skb) {
- __le64 info = rxfd->frag_info;
-
- pci_unmap_single(sp->pdev,
- le64_to_cpu(info) & ~IPG_RFI_FRAGLEN,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE);
-
- dev_kfree_skb_irq(skb);
- }
- } else {
-
- /* Adjust the new buffer length to accommodate the size
- * of the received frame.
- */
- skb_put(skb, framelen);
-
- /* Set the buffer's protocol field to Ethernet. */
- skb->protocol = eth_type_trans(skb, dev);
-
- /* The IPG encountered an error with (or
- * there were no) IP/TCP/UDP checksums.
- * This may or may not indicate an invalid
- * IP/TCP/UDP frame was received. Let the
- * upper layer decide.
- */
- skb_checksum_none_assert(skb);
-
- /* Hand off frame for higher layer processing.
- * The function netif_rx() releases the sk_buff
- * when processing completes.
- */
- netif_rx(skb);
- }
-
- /* Assure RX buffer is not reused by IPG. */
- sp->rx_buff[entry] = NULL;
- }
-
- /*
- * If there are more RFDs to process and the allocated amount of RFD
- * processing time has expired, assert Interrupt Requested to make
- * sure we come back to process the remaining RFDs.
- */
- if (i == IPG_MAXRFDPROCESS_COUNT)
- ipg_w32(ipg_r32(ASIC_CTRL) | IPG_AC_INT_REQUEST, ASIC_CTRL);
-
-#ifdef IPG_DEBUG
- /* Check if the RFD list contained no receive frame data. */
- if (!i)
- sp->EmptyRFDListCount++;
-#endif
- while ((le64_to_cpu(rxfd->rfs) & IPG_RFS_RFDDONE) &&
- !((le64_to_cpu(rxfd->rfs) & IPG_RFS_FRAMESTART) &&
- (le64_to_cpu(rxfd->rfs) & IPG_RFS_FRAMEEND))) {
- unsigned int entry = curr++ % IPG_RFDLIST_LENGTH;
-
- rxfd = sp->rxd + entry;
-
- IPG_DEBUG_MSG("Frame requires multiple RFDs\n");
-
- /* An unexpected event, additional code needed to handle
- * properly. So for the time being, just disregard the
- * frame.
- */
-
- /* Free the memory associated with the RX
- * buffer since it is erroneous and we will
- * not pass it to higher layer processes.
- */
- if (sp->rx_buff[entry]) {
- pci_unmap_single(sp->pdev,
- le64_to_cpu(rxfd->frag_info) & ~IPG_RFI_FRAGLEN,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE);
- dev_kfree_skb_irq(sp->rx_buff[entry]);
- }
-
- /* Assure RX buffer is not reused by IPG. */
- sp->rx_buff[entry] = NULL;
- }
-
- sp->rx_current = curr;
-
- /* Check to see if there are a minimum number of used
- * RFDs before restoring any (should improve performance.)
- */
- if ((curr - sp->rx_dirty) >= IPG_MINUSEDRFDSTOFREE)
- ipg_nic_rxrestore(dev);
-
- return 0;
-}
-
-static void ipg_reset_after_host_error(struct work_struct *work)
-{
- struct ipg_nic_private *sp =
- container_of(work, struct ipg_nic_private, task.work);
- struct net_device *dev = sp->dev;
-
- /*
- * Acknowledge HostError interrupt by resetting
- * IPG DMA and HOST.
- */
- ipg_reset(dev, IPG_AC_GLOBAL_RESET | IPG_AC_HOST | IPG_AC_DMA);
-
- init_rfdlist(dev);
- init_tfdlist(dev);
-
- if (ipg_io_config(dev) < 0) {
- netdev_info(dev, "Cannot recover from PCI error\n");
- schedule_delayed_work(&sp->task, HZ);
- }
-}
-
-static irqreturn_t ipg_interrupt_handler(int irq, void *dev_inst)
-{
- struct net_device *dev = dev_inst;
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int handled = 0;
- u16 status;
-
- IPG_DEBUG_MSG("_interrupt_handler\n");
-
- if (sp->is_jumbo)
- ipg_nic_rxrestore(dev);
-
- spin_lock(&sp->lock);
-
- /* Get interrupt source information, and acknowledge
- * some (i.e. TxDMAComplete, RxDMAComplete, RxEarly,
- * IntRequested, MacControlFrame, LinkEvent) interrupts
- * if issued. Also, all IPG interrupts are disabled by
- * reading IntStatusAck.
- */
- status = ipg_r16(INT_STATUS_ACK);
-
- IPG_DEBUG_MSG("IntStatusAck = %04x\n", status);
-
- /* Shared IRQ of remove event. */
- if (!(status & IPG_IS_RSVD_MASK))
- goto out_enable;
-
- handled = 1;
-
- if (unlikely(!netif_running(dev)))
- goto out_unlock;
-
- /* If RFDListEnd interrupt, restore all used RFDs. */
- if (status & IPG_IS_RFD_LIST_END) {
- IPG_DEBUG_MSG("RFDListEnd Interrupt\n");
-
- /* The RFD list end indicates an RFD was encountered
- * with a 0 NextPtr, or with an RFDDone bit set to 1
- * (indicating the RFD is not read for use by the
- * IPG.) Try to restore all RFDs.
- */
- ipg_nic_rxrestore(dev);
-
-#ifdef IPG_DEBUG
- /* Increment the RFDlistendCount counter. */
- sp->RFDlistendCount++;
-#endif
- }
-
- /* If RFDListEnd, RxDMAPriority, RxDMAComplete, or
- * IntRequested interrupt, process received frames. */
- if ((status & IPG_IS_RX_DMA_PRIORITY) ||
- (status & IPG_IS_RFD_LIST_END) ||
- (status & IPG_IS_RX_DMA_COMPLETE) ||
- (status & IPG_IS_INT_REQUESTED)) {
-#ifdef IPG_DEBUG
- /* Increment the RFD list checked counter if interrupted
- * only to check the RFD list. */
- if (status & (~(IPG_IS_RX_DMA_PRIORITY | IPG_IS_RFD_LIST_END |
- IPG_IS_RX_DMA_COMPLETE | IPG_IS_INT_REQUESTED) &
- (IPG_IS_HOST_ERROR | IPG_IS_TX_DMA_COMPLETE |
- IPG_IS_LINK_EVENT | IPG_IS_TX_COMPLETE |
- IPG_IS_UPDATE_STATS)))
- sp->RFDListCheckedCount++;
-#endif
-
- if (sp->is_jumbo)
- ipg_nic_rx_jumbo(dev);
- else
- ipg_nic_rx(dev);
- }
-
- /* If TxDMAComplete interrupt, free used TFDs. */
- if (status & IPG_IS_TX_DMA_COMPLETE)
- ipg_nic_txfree(dev);
-
- /* TxComplete interrupts indicate one of numerous actions.
- * Determine what action to take based on TXSTATUS register.
- */
- if (status & IPG_IS_TX_COMPLETE)
- ipg_nic_txcleanup(dev);
-
- /* If UpdateStats interrupt, update Linux Ethernet statistics */
- if (status & IPG_IS_UPDATE_STATS)
- ipg_nic_get_stats(dev);
-
- /* If HostError interrupt, reset IPG. */
- if (status & IPG_IS_HOST_ERROR) {
- IPG_DDEBUG_MSG("HostError Interrupt\n");
-
- schedule_delayed_work(&sp->task, 0);
- }
-
- /* If LinkEvent interrupt, resolve autonegotiation. */
- if (status & IPG_IS_LINK_EVENT) {
- if (ipg_config_autoneg(dev) < 0)
- netdev_info(dev, "Auto-negotiation error\n");
- }
-
- /* If MACCtrlFrame interrupt, do nothing. */
- if (status & IPG_IS_MAC_CTRL_FRAME)
- IPG_DEBUG_MSG("MACCtrlFrame interrupt\n");
-
- /* If RxComplete interrupt, do nothing. */
- if (status & IPG_IS_RX_COMPLETE)
- IPG_DEBUG_MSG("RxComplete interrupt\n");
-
- /* If RxEarly interrupt, do nothing. */
- if (status & IPG_IS_RX_EARLY)
- IPG_DEBUG_MSG("RxEarly interrupt\n");
-
-out_enable:
- /* Re-enable IPG interrupts. */
- ipg_w16(IPG_IE_TX_DMA_COMPLETE | IPG_IE_RX_DMA_COMPLETE |
- IPG_IE_HOST_ERROR | IPG_IE_INT_REQUESTED | IPG_IE_TX_COMPLETE |
- IPG_IE_LINK_EVENT | IPG_IE_UPDATE_STATS, INT_ENABLE);
-out_unlock:
- spin_unlock(&sp->lock);
-
- return IRQ_RETVAL(handled);
-}
-
-static void ipg_rx_clear(struct ipg_nic_private *sp)
-{
- unsigned int i;
-
- for (i = 0; i < IPG_RFDLIST_LENGTH; i++) {
- if (sp->rx_buff[i]) {
- struct ipg_rx *rxfd = sp->rxd + i;
-
- dev_kfree_skb_irq(sp->rx_buff[i]);
- sp->rx_buff[i] = NULL;
- pci_unmap_single(sp->pdev,
- le64_to_cpu(rxfd->frag_info) & ~IPG_RFI_FRAGLEN,
- sp->rx_buf_sz, PCI_DMA_FROMDEVICE);
- }
- }
-}
-
-static void ipg_tx_clear(struct ipg_nic_private *sp)
-{
- unsigned int i;
-
- for (i = 0; i < IPG_TFDLIST_LENGTH; i++) {
- if (sp->tx_buff[i]) {
- struct ipg_tx *txfd = sp->txd + i;
-
- pci_unmap_single(sp->pdev,
- le64_to_cpu(txfd->frag_info) & ~IPG_TFI_FRAGLEN,
- sp->tx_buff[i]->len, PCI_DMA_TODEVICE);
-
- dev_kfree_skb_irq(sp->tx_buff[i]);
-
- sp->tx_buff[i] = NULL;
- }
- }
-}
-
-static int ipg_nic_open(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- struct pci_dev *pdev = sp->pdev;
- int rc;
-
- IPG_DEBUG_MSG("_nic_open\n");
-
- sp->rx_buf_sz = sp->rxsupport_size;
-
- /* Check for interrupt line conflicts, and request interrupt
- * line for IPG.
- *
- * IMPORTANT: Disable IPG interrupts prior to registering
- * IRQ.
- */
- ipg_w16(0x0000, INT_ENABLE);
-
- /* Register the interrupt line to be used by the IPG within
- * the Linux system.
- */
- rc = request_irq(pdev->irq, ipg_interrupt_handler, IRQF_SHARED,
- dev->name, dev);
- if (rc < 0) {
- netdev_info(dev, "Error when requesting interrupt\n");
- goto out;
- }
-
- dev->irq = pdev->irq;
-
- rc = -ENOMEM;
-
- sp->rxd = dma_alloc_coherent(&pdev->dev, IPG_RX_RING_BYTES,
- &sp->rxd_map, GFP_KERNEL);
- if (!sp->rxd)
- goto err_free_irq_0;
-
- sp->txd = dma_alloc_coherent(&pdev->dev, IPG_TX_RING_BYTES,
- &sp->txd_map, GFP_KERNEL);
- if (!sp->txd)
- goto err_free_rx_1;
-
- rc = init_rfdlist(dev);
- if (rc < 0) {
- netdev_info(dev, "Error during configuration\n");
- goto err_free_tx_2;
- }
-
- init_tfdlist(dev);
-
- rc = ipg_io_config(dev);
- if (rc < 0) {
- netdev_info(dev, "Error during configuration\n");
- goto err_release_tfdlist_3;
- }
-
- /* Resolve autonegotiation. */
- if (ipg_config_autoneg(dev) < 0)
- netdev_info(dev, "Auto-negotiation error\n");
-
- /* initialize JUMBO Frame control variable */
- sp->jumbo.found_start = 0;
- sp->jumbo.current_size = 0;
- sp->jumbo.skb = NULL;
-
- /* Enable transmit and receive operation of the IPG. */
- ipg_w32((ipg_r32(MAC_CTRL) | IPG_MC_RX_ENABLE | IPG_MC_TX_ENABLE) &
- IPG_MC_RSVD_MASK, MAC_CTRL);
-
- netif_start_queue(dev);
-out:
- return rc;
-
-err_release_tfdlist_3:
- ipg_tx_clear(sp);
- ipg_rx_clear(sp);
-err_free_tx_2:
- dma_free_coherent(&pdev->dev, IPG_TX_RING_BYTES, sp->txd, sp->txd_map);
-err_free_rx_1:
- dma_free_coherent(&pdev->dev, IPG_RX_RING_BYTES, sp->rxd, sp->rxd_map);
-err_free_irq_0:
- free_irq(pdev->irq, dev);
- goto out;
-}
-
-static int ipg_nic_stop(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- struct pci_dev *pdev = sp->pdev;
-
- IPG_DEBUG_MSG("_nic_stop\n");
-
- netif_stop_queue(dev);
-
- IPG_DUMPTFDLIST(dev);
-
- do {
- (void) ipg_r16(INT_STATUS_ACK);
-
- ipg_reset(dev, IPG_AC_GLOBAL_RESET | IPG_AC_HOST | IPG_AC_DMA);
-
- synchronize_irq(pdev->irq);
- } while (ipg_r16(INT_ENABLE) & IPG_IE_RSVD_MASK);
-
- ipg_rx_clear(sp);
-
- ipg_tx_clear(sp);
-
- pci_free_consistent(pdev, IPG_RX_RING_BYTES, sp->rxd, sp->rxd_map);
- pci_free_consistent(pdev, IPG_TX_RING_BYTES, sp->txd, sp->txd_map);
-
- free_irq(pdev->irq, dev);
-
- return 0;
-}
-
-static netdev_tx_t ipg_nic_hard_start_xmit(struct sk_buff *skb,
- struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int entry = sp->tx_current % IPG_TFDLIST_LENGTH;
- unsigned long flags;
- struct ipg_tx *txfd;
-
- IPG_DDEBUG_MSG("_nic_hard_start_xmit\n");
-
- /* If in 10Mbps mode, stop the transmit queue so
- * no more transmit frames are accepted.
- */
- if (sp->tenmbpsmode)
- netif_stop_queue(dev);
-
- if (sp->reset_current_tfd) {
- sp->reset_current_tfd = 0;
- entry = 0;
- }
-
- txfd = sp->txd + entry;
-
- sp->tx_buff[entry] = skb;
-
- /* Clear all TFC fields, except TFDDONE. */
- txfd->tfc = cpu_to_le64(IPG_TFC_TFDDONE);
-
- /* Specify the TFC field within the TFD. */
- txfd->tfc |= cpu_to_le64(IPG_TFC_WORDALIGNDISABLED |
- (IPG_TFC_FRAMEID & sp->tx_current) |
- (IPG_TFC_FRAGCOUNT & (1 << 24)));
- /*
- * 16--17 (WordAlign) <- 3 (disable),
- * 0--15 (FrameId) <- sp->tx_current,
- * 24--27 (FragCount) <- 1
- */
-
- /* Request TxComplete interrupts at an interval defined
- * by the constant IPG_FRAMESBETWEENTXCOMPLETES.
- * Request TxComplete interrupt for every frame
- * if in 10Mbps mode to accommodate problem with 10Mbps
- * processing.
- */
- if (sp->tenmbpsmode)
- txfd->tfc |= cpu_to_le64(IPG_TFC_TXINDICATE);
- txfd->tfc |= cpu_to_le64(IPG_TFC_TXDMAINDICATE);
- /* Based on compilation option, determine if FCS is to be
- * appended to transmit frame by IPG.
- */
- if (!(IPG_APPEND_FCS_ON_TX))
- txfd->tfc |= cpu_to_le64(IPG_TFC_FCSAPPENDDISABLE);
-
- /* Based on compilation option, determine if IP, TCP and/or
- * UDP checksums are to be added to transmit frame by IPG.
- */
- if (IPG_ADD_IPCHECKSUM_ON_TX)
- txfd->tfc |= cpu_to_le64(IPG_TFC_IPCHECKSUMENABLE);
-
- if (IPG_ADD_TCPCHECKSUM_ON_TX)
- txfd->tfc |= cpu_to_le64(IPG_TFC_TCPCHECKSUMENABLE);
-
- if (IPG_ADD_UDPCHECKSUM_ON_TX)
- txfd->tfc |= cpu_to_le64(IPG_TFC_UDPCHECKSUMENABLE);
-
- /* Based on compilation option, determine if VLAN tag info is to be
- * inserted into transmit frame by IPG.
- */
- if (IPG_INSERT_MANUAL_VLAN_TAG) {
- txfd->tfc |= cpu_to_le64(IPG_TFC_VLANTAGINSERT |
- ((u64) IPG_MANUAL_VLAN_VID << 32) |
- ((u64) IPG_MANUAL_VLAN_CFI << 44) |
- ((u64) IPG_MANUAL_VLAN_USERPRIORITY << 45));
- }
-
- /* The fragment start location within system memory is defined
- * by the sk_buff structure's data field. The physical address
- * of this location within the system's virtual memory space
- * is determined using the IPG_HOST2BUS_MAP function.
- */
- txfd->frag_info = cpu_to_le64(pci_map_single(sp->pdev, skb->data,
- skb->len, PCI_DMA_TODEVICE));
-
- /* The length of the fragment within system memory is defined by
- * the sk_buff structure's len field.
- */
- txfd->frag_info |= cpu_to_le64(IPG_TFI_FRAGLEN &
- ((u64) (skb->len & 0xffff) << 48));
-
- /* Clear the TFDDone bit last to indicate the TFD is ready
- * for transfer to the IPG.
- */
- txfd->tfc &= cpu_to_le64(~IPG_TFC_TFDDONE);
-
- spin_lock_irqsave(&sp->lock, flags);
-
- sp->tx_current++;
-
- mmiowb();
-
- ipg_w32(IPG_DC_TX_DMA_POLL_NOW, DMA_CTRL);
-
- if (sp->tx_current == (sp->tx_dirty + IPG_TFDLIST_LENGTH))
- netif_stop_queue(dev);
-
- spin_unlock_irqrestore(&sp->lock, flags);
-
- return NETDEV_TX_OK;
-}
-
-static void ipg_set_phy_default_param(unsigned char rev,
- struct net_device *dev, int phy_address)
-{
- unsigned short length;
- unsigned char revision;
- const unsigned short *phy_param;
- unsigned short address, value;
-
- phy_param = &DefaultPhyParam[0];
- length = *phy_param & 0x00FF;
- revision = (unsigned char)((*phy_param) >> 8);
- phy_param++;
- while (length != 0) {
- if (rev == revision) {
- while (length > 1) {
- address = *phy_param;
- value = *(phy_param + 1);
- phy_param += 2;
- mdio_write(dev, phy_address, address, value);
- length -= 4;
- }
- break;
- } else {
- phy_param += length / 2;
- length = *phy_param & 0x00FF;
- revision = (unsigned char)((*phy_param) >> 8);
- phy_param++;
- }
- }
-}
-
-static int read_eeprom(struct net_device *dev, int eep_addr)
-{
- void __iomem *ioaddr = ipg_ioaddr(dev);
- unsigned int i;
- int ret = 0;
- u16 value;
-
- value = IPG_EC_EEPROM_READOPCODE | (eep_addr & 0xff);
- ipg_w16(value, EEPROM_CTRL);
-
- for (i = 0; i < 1000; i++) {
- u16 data;
-
- mdelay(10);
- data = ipg_r16(EEPROM_CTRL);
- if (!(data & IPG_EC_EEPROM_BUSY)) {
- ret = ipg_r16(EEPROM_DATA);
- break;
- }
- }
- return ret;
-}
-
-static void ipg_init_mii(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- struct mii_if_info *mii_if = &sp->mii_if;
- int phyaddr;
-
- mii_if->dev = dev;
- mii_if->mdio_read = mdio_read;
- mii_if->mdio_write = mdio_write;
- mii_if->phy_id_mask = 0x1f;
- mii_if->reg_num_mask = 0x1f;
-
- mii_if->phy_id = phyaddr = ipg_find_phyaddr(dev);
-
- if (phyaddr != 0x1f) {
- u16 mii_phyctrl, mii_1000cr;
-
- mii_1000cr = mdio_read(dev, phyaddr, MII_CTRL1000);
- mii_1000cr |= ADVERTISE_1000FULL | ADVERTISE_1000HALF |
- GMII_PHY_1000BASETCONTROL_PreferMaster;
- mdio_write(dev, phyaddr, MII_CTRL1000, mii_1000cr);
-
- mii_phyctrl = mdio_read(dev, phyaddr, MII_BMCR);
-
- /* Set default phyparam */
- ipg_set_phy_default_param(sp->pdev->revision, dev, phyaddr);
-
- /* Reset PHY */
- mii_phyctrl |= BMCR_RESET | BMCR_ANRESTART;
- mdio_write(dev, phyaddr, MII_BMCR, mii_phyctrl);
-
- }
-}
-
-static int ipg_hw_init(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- void __iomem *ioaddr = sp->ioaddr;
- unsigned int i;
- int rc;
-
- /* Read/Write and Reset EEPROM Value */
- /* Read LED Mode Configuration from EEPROM */
- sp->led_mode = read_eeprom(dev, 6);
-
- /* Reset all functions within the IPG. Do not assert
- * RST_OUT as not compatible with some PHYs.
- */
- rc = ipg_reset(dev, IPG_RESET_MASK);
- if (rc < 0)
- goto out;
-
- ipg_init_mii(dev);
-
- /* Read MAC Address from EEPROM */
- for (i = 0; i < 3; i++)
- sp->station_addr[i] = read_eeprom(dev, 16 + i);
-
- for (i = 0; i < 3; i++)
- ipg_w16(sp->station_addr[i], STATION_ADDRESS_0 + 2*i);
-
- /* Set station address in ethernet_device structure. */
- dev->dev_addr[0] = ipg_r16(STATION_ADDRESS_0) & 0x00ff;
- dev->dev_addr[1] = (ipg_r16(STATION_ADDRESS_0) & 0xff00) >> 8;
- dev->dev_addr[2] = ipg_r16(STATION_ADDRESS_1) & 0x00ff;
- dev->dev_addr[3] = (ipg_r16(STATION_ADDRESS_1) & 0xff00) >> 8;
- dev->dev_addr[4] = ipg_r16(STATION_ADDRESS_2) & 0x00ff;
- dev->dev_addr[5] = (ipg_r16(STATION_ADDRESS_2) & 0xff00) >> 8;
-out:
- return rc;
-}
-
-static int ipg_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- int rc;
-
- mutex_lock(&sp->mii_mutex);
- rc = generic_mii_ioctl(&sp->mii_if, if_mii(ifr), cmd, NULL);
- mutex_unlock(&sp->mii_mutex);
-
- return rc;
-}
-
-static int ipg_nic_change_mtu(struct net_device *dev, int new_mtu)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- int err;
-
- /* Function to accommodate changes to Maximum Transfer Unit
- * (or MTU) of IPG NIC. Cannot use default function since
- * the default will not allow for MTU > 1500 bytes.
- */
-
- IPG_DEBUG_MSG("_nic_change_mtu\n");
-
- /*
- * Check that the new MTU value is between 68 (14 byte header, 46 byte
- * payload, 4 byte FCS) and 10 KB, which is the largest supported MTU.
- */
- if (new_mtu < 68 || new_mtu > 10240)
- return -EINVAL;
-
- err = ipg_nic_stop(dev);
- if (err)
- return err;
-
- dev->mtu = new_mtu;
-
- sp->max_rxframe_size = new_mtu;
-
- sp->rxfrag_size = new_mtu;
- if (sp->rxfrag_size > 4088)
- sp->rxfrag_size = 4088;
-
- sp->rxsupport_size = sp->max_rxframe_size;
-
- if (new_mtu > 0x0600)
- sp->is_jumbo = true;
- else
- sp->is_jumbo = false;
-
- return ipg_nic_open(dev);
-}
-
-static int ipg_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- int rc;
-
- mutex_lock(&sp->mii_mutex);
- rc = mii_ethtool_gset(&sp->mii_if, cmd);
- mutex_unlock(&sp->mii_mutex);
-
- return rc;
-}
-
-static int ipg_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- int rc;
-
- mutex_lock(&sp->mii_mutex);
- rc = mii_ethtool_sset(&sp->mii_if, cmd);
- mutex_unlock(&sp->mii_mutex);
-
- return rc;
-}
-
-static int ipg_nway_reset(struct net_device *dev)
-{
- struct ipg_nic_private *sp = netdev_priv(dev);
- int rc;
-
- mutex_lock(&sp->mii_mutex);
- rc = mii_nway_restart(&sp->mii_if);
- mutex_unlock(&sp->mii_mutex);
-
- return rc;
-}
-
-static const struct ethtool_ops ipg_ethtool_ops = {
- .get_settings = ipg_get_settings,
- .set_settings = ipg_set_settings,
- .nway_reset = ipg_nway_reset,
-};
-
-static void ipg_remove(struct pci_dev *pdev)
-{
- struct net_device *dev = pci_get_drvdata(pdev);
- struct ipg_nic_private *sp = netdev_priv(dev);
-
- IPG_DEBUG_MSG("_remove\n");
-
- /* Un-register Ethernet device. */
- unregister_netdev(dev);
-
- pci_iounmap(pdev, sp->ioaddr);
-
- pci_release_regions(pdev);
-
- free_netdev(dev);
- pci_disable_device(pdev);
-}
-
-static const struct net_device_ops ipg_netdev_ops = {
- .ndo_open = ipg_nic_open,
- .ndo_stop = ipg_nic_stop,
- .ndo_start_xmit = ipg_nic_hard_start_xmit,
- .ndo_get_stats = ipg_nic_get_stats,
- .ndo_set_rx_mode = ipg_nic_set_multicast_list,
- .ndo_do_ioctl = ipg_ioctl,
- .ndo_tx_timeout = ipg_tx_timeout,
- .ndo_change_mtu = ipg_nic_change_mtu,
- .ndo_set_mac_address = eth_mac_addr,
- .ndo_validate_addr = eth_validate_addr,
-};
-
-static int ipg_probe(struct pci_dev *pdev, const struct pci_device_id *id)
-{
- unsigned int i = id->driver_data;
- struct ipg_nic_private *sp;
- struct net_device *dev;
- void __iomem *ioaddr;
- int rc;
-
- rc = pci_enable_device(pdev);
- if (rc < 0)
- goto out;
-
- pr_info("%s: %s\n", pci_name(pdev), ipg_brand_name[i]);
-
- pci_set_master(pdev);
-
- rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(40));
- if (rc < 0) {
- rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
- if (rc < 0) {
- pr_err("%s: DMA config failed\n", pci_name(pdev));
- goto err_disable_0;
- }
- }
-
- /*
- * Initialize net device.
- */
- dev = alloc_etherdev(sizeof(struct ipg_nic_private));
- if (!dev) {
- rc = -ENOMEM;
- goto err_disable_0;
- }
-
- sp = netdev_priv(dev);
- spin_lock_init(&sp->lock);
- mutex_init(&sp->mii_mutex);
-
- sp->is_jumbo = IPG_IS_JUMBO;
- sp->rxfrag_size = IPG_RXFRAG_SIZE;
- sp->rxsupport_size = IPG_RXSUPPORT_SIZE;
- sp->max_rxframe_size = IPG_MAX_RXFRAME_SIZE;
-
- /* Declare IPG NIC functions for Ethernet device methods.
- */
- dev->netdev_ops = &ipg_netdev_ops;
- SET_NETDEV_DEV(dev, &pdev->dev);
- dev->ethtool_ops = &ipg_ethtool_ops;
-
- rc = pci_request_regions(pdev, DRV_NAME);
- if (rc)
- goto err_free_dev_1;
-
- ioaddr = pci_iomap(pdev, 1, pci_resource_len(pdev, 1));
- if (!ioaddr) {
- pr_err("%s: cannot map MMIO\n", pci_name(pdev));
- rc = -EIO;
- goto err_release_regions_2;
- }
-
- /* Save the pointer to the PCI device information. */
- sp->ioaddr = ioaddr;
- sp->pdev = pdev;
- sp->dev = dev;
-
- INIT_DELAYED_WORK(&sp->task, ipg_reset_after_host_error);
-
- pci_set_drvdata(pdev, dev);
-
- rc = ipg_hw_init(dev);
- if (rc < 0)
- goto err_unmap_3;
-
- rc = register_netdev(dev);
- if (rc < 0)
- goto err_unmap_3;
-
- netdev_info(dev, "Ethernet device registered\n");
-out:
- return rc;
-
-err_unmap_3:
- pci_iounmap(pdev, ioaddr);
-err_release_regions_2:
- pci_release_regions(pdev);
-err_free_dev_1:
- free_netdev(dev);
-err_disable_0:
- pci_disable_device(pdev);
- goto out;
-}
-
-static struct pci_driver ipg_pci_driver = {
- .name = IPG_DRIVER_NAME,
- .id_table = ipg_pci_tbl,
- .probe = ipg_probe,
- .remove = ipg_remove,
-};
-
-module_pci_driver(ipg_pci_driver);
diff --git a/drivers/net/ethernet/icplus/ipg.h b/drivers/net/ethernet/icplus/ipg.h
deleted file mode 100644
index de60628..0000000
--- a/drivers/net/ethernet/icplus/ipg.h
+++ /dev/null
@@ -1,748 +0,0 @@
-/*
- * Include file for Gigabit Ethernet device driver for Network
- * Interface Cards (NICs) utilizing the Tamarack Microelectronics
- * Inc. IPG Gigabit or Triple Speed Ethernet Media Access
- * Controller.
- */
-#ifndef __LINUX_IPG_H
-#define __LINUX_IPG_H
-
-#include <linux/module.h>
-
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/ioport.h>
-#include <linux/errno.h>
-#include <asm/io.h>
-#include <linux/delay.h>
-#include <linux/types.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <asm/bitops.h>
-
-/*
- * Constants
- */
-
-/* GMII based PHY IDs */
-#define NS 0x2000
-#define MARVELL 0x0141
-#define ICPLUS_PHY 0x243
-
-/* NIC Physical Layer Device MII register fields. */
-#define MII_PHY_SELECTOR_IEEE8023 0x0001
-#define MII_PHY_TECHABILITYFIELD 0x1FE0
-
-/* GMII_PHY_1000 need to set to prefer master */
-#define GMII_PHY_1000BASETCONTROL_PreferMaster 0x0400
-
-/* NIC Physical Layer Device GMII constants. */
-#define GMII_PREAMBLE 0xFFFFFFFF
-#define GMII_ST 0x1
-#define GMII_READ 0x2
-#define GMII_WRITE 0x1
-#define GMII_TA_READ_MASK 0x1
-#define GMII_TA_WRITE 0x2
-
-/* I/O register offsets. */
-enum ipg_regs {
- DMA_CTRL = 0x00,
- RX_DMA_STATUS = 0x08, /* Unused + reserved */
- TFD_LIST_PTR_0 = 0x10,
- TFD_LIST_PTR_1 = 0x14,
- TX_DMA_BURST_THRESH = 0x18,
- TX_DMA_URGENT_THRESH = 0x19,
- TX_DMA_POLL_PERIOD = 0x1a,
- RFD_LIST_PTR_0 = 0x1c,
- RFD_LIST_PTR_1 = 0x20,
- RX_DMA_BURST_THRESH = 0x24,
- RX_DMA_URGENT_THRESH = 0x25,
- RX_DMA_POLL_PERIOD = 0x26,
- DEBUG_CTRL = 0x2c,
- ASIC_CTRL = 0x30,
- FIFO_CTRL = 0x38, /* Unused */
- FLOW_OFF_THRESH = 0x3c,
- FLOW_ON_THRESH = 0x3e,
- EEPROM_DATA = 0x48,
- EEPROM_CTRL = 0x4a,
- EXPROM_ADDR = 0x4c, /* Unused */
- EXPROM_DATA = 0x50, /* Unused */
- WAKE_EVENT = 0x51, /* Unused */
- COUNTDOWN = 0x54, /* Unused */
- INT_STATUS_ACK = 0x5a,
- INT_ENABLE = 0x5c,
- INT_STATUS = 0x5e, /* Unused */
- TX_STATUS = 0x60,
- MAC_CTRL = 0x6c,
- VLAN_TAG = 0x70, /* Unused */
- PHY_SET = 0x75,
- PHY_CTRL = 0x76,
- STATION_ADDRESS_0 = 0x78,
- STATION_ADDRESS_1 = 0x7a,
- STATION_ADDRESS_2 = 0x7c,
- MAX_FRAME_SIZE = 0x86,
- RECEIVE_MODE = 0x88,
- HASHTABLE_0 = 0x8c,
- HASHTABLE_1 = 0x90,
- RMON_STATISTICS_MASK = 0x98,
- STATISTICS_MASK = 0x9c,
- RX_JUMBO_FRAMES = 0xbc, /* Unused */
- TCP_CHECKSUM_ERRORS = 0xc0, /* Unused */
- IP_CHECKSUM_ERRORS = 0xc2, /* Unused */
- UDP_CHECKSUM_ERRORS = 0xc4, /* Unused */
- TX_JUMBO_FRAMES = 0xf4 /* Unused */
-};
-
-/* Ethernet MIB statistic register offsets. */
-#define IPG_OCTETRCVOK 0xA8
-#define IPG_MCSTOCTETRCVDOK 0xAC
-#define IPG_BCSTOCTETRCVOK 0xB0
-#define IPG_FRAMESRCVDOK 0xB4
-#define IPG_MCSTFRAMESRCVDOK 0xB8
-#define IPG_BCSTFRAMESRCVDOK 0xBE
-#define IPG_MACCONTROLFRAMESRCVD 0xC6
-#define IPG_FRAMETOOLONGERRORS 0xC8
-#define IPG_INRANGELENGTHERRORS 0xCA
-#define IPG_FRAMECHECKSEQERRORS 0xCC
-#define IPG_FRAMESLOSTRXERRORS 0xCE
-#define IPG_OCTETXMTOK 0xD0
-#define IPG_MCSTOCTETXMTOK 0xD4
-#define IPG_BCSTOCTETXMTOK 0xD8
-#define IPG_FRAMESXMTDOK 0xDC
-#define IPG_MCSTFRAMESXMTDOK 0xE0
-#define IPG_FRAMESWDEFERREDXMT 0xE4
-#define IPG_LATECOLLISIONS 0xE8
-#define IPG_MULTICOLFRAMES 0xEC
-#define IPG_SINGLECOLFRAMES 0xF0
-#define IPG_BCSTFRAMESXMTDOK 0xF6
-#define IPG_CARRIERSENSEERRORS 0xF8
-#define IPG_MACCONTROLFRAMESXMTDOK 0xFA
-#define IPG_FRAMESABORTXSCOLLS 0xFC
-#define IPG_FRAMESWEXDEFERRAL 0xFE
-
-/* RMON statistic register offsets. */
-#define IPG_ETHERSTATSCOLLISIONS 0x100
-#define IPG_ETHERSTATSOCTETSTRANSMIT 0x104
-#define IPG_ETHERSTATSPKTSTRANSMIT 0x108
-#define IPG_ETHERSTATSPKTS64OCTESTSTRANSMIT 0x10C
-#define IPG_ETHERSTATSPKTS65TO127OCTESTSTRANSMIT 0x110
-#define IPG_ETHERSTATSPKTS128TO255OCTESTSTRANSMIT 0x114
-#define IPG_ETHERSTATSPKTS256TO511OCTESTSTRANSMIT 0x118
-#define IPG_ETHERSTATSPKTS512TO1023OCTESTSTRANSMIT 0x11C
-#define IPG_ETHERSTATSPKTS1024TO1518OCTESTSTRANSMIT 0x120
-#define IPG_ETHERSTATSCRCALIGNERRORS 0x124
-#define IPG_ETHERSTATSUNDERSIZEPKTS 0x128
-#define IPG_ETHERSTATSFRAGMENTS 0x12C
-#define IPG_ETHERSTATSJABBERS 0x130
-#define IPG_ETHERSTATSOCTETS 0x134
-#define IPG_ETHERSTATSPKTS 0x138
-#define IPG_ETHERSTATSPKTS64OCTESTS 0x13C
-#define IPG_ETHERSTATSPKTS65TO127OCTESTS 0x140
-#define IPG_ETHERSTATSPKTS128TO255OCTESTS 0x144
-#define IPG_ETHERSTATSPKTS256TO511OCTESTS 0x148
-#define IPG_ETHERSTATSPKTS512TO1023OCTESTS 0x14C
-#define IPG_ETHERSTATSPKTS1024TO1518OCTESTS 0x150
-
-/* RMON statistic register equivalents. */
-#define IPG_ETHERSTATSMULTICASTPKTSTRANSMIT 0xE0
-#define IPG_ETHERSTATSBROADCASTPKTSTRANSMIT 0xF6
-#define IPG_ETHERSTATSMULTICASTPKTS 0xB8
-#define IPG_ETHERSTATSBROADCASTPKTS 0xBE
-#define IPG_ETHERSTATSOVERSIZEPKTS 0xC8
-#define IPG_ETHERSTATSDROPEVENTS 0xCE
-
-/* Serial EEPROM offsets */
-#define IPG_EEPROM_CONFIGPARAM 0x00
-#define IPG_EEPROM_ASICCTRL 0x01
-#define IPG_EEPROM_SUBSYSTEMVENDORID 0x02
-#define IPG_EEPROM_SUBSYSTEMID 0x03
-#define IPG_EEPROM_STATIONADDRESS0 0x10
-#define IPG_EEPROM_STATIONADDRESS1 0x11
-#define IPG_EEPROM_STATIONADDRESS2 0x12
-
-/* Register & data structure bit masks */
-
-/* PCI register masks. */
-
-/* IOBaseAddress */
-#define IPG_PIB_RSVD_MASK 0xFFFFFE01
-#define IPG_PIB_IOBASEADDRESS 0xFFFFFF00
-#define IPG_PIB_IOBASEADDRIND 0x00000001
-
-/* MemBaseAddress */
-#define IPG_PMB_RSVD_MASK 0xFFFFFE07
-#define IPG_PMB_MEMBASEADDRIND 0x00000001
-#define IPG_PMB_MEMMAPTYPE 0x00000006
-#define IPG_PMB_MEMMAPTYPE0 0x00000002
-#define IPG_PMB_MEMMAPTYPE1 0x00000004
-#define IPG_PMB_MEMBASEADDRESS 0xFFFFFE00
-
-/* ConfigStatus */
-#define IPG_CS_RSVD_MASK 0xFFB0
-#define IPG_CS_CAPABILITIES 0x0010
-#define IPG_CS_66MHZCAPABLE 0x0020
-#define IPG_CS_FASTBACK2BACK 0x0080
-#define IPG_CS_DATAPARITYREPORTED 0x0100
-#define IPG_CS_DEVSELTIMING 0x0600
-#define IPG_CS_SIGNALEDTARGETABORT 0x0800
-#define IPG_CS_RECEIVEDTARGETABORT 0x1000
-#define IPG_CS_RECEIVEDMASTERABORT 0x2000
-#define IPG_CS_SIGNALEDSYSTEMERROR 0x4000
-#define IPG_CS_DETECTEDPARITYERROR 0x8000
-
-/* TFD data structure masks. */
-
-/* TFDList, TFC */
-#define IPG_TFC_RSVD_MASK 0x0000FFFF9FFFFFFFULL
-#define IPG_TFC_FRAMEID 0x000000000000FFFFULL
-#define IPG_TFC_WORDALIGN 0x0000000000030000ULL
-#define IPG_TFC_WORDALIGNTODWORD 0x0000000000000000ULL
-#define IPG_TFC_WORDALIGNTOWORD 0x0000000000020000ULL
-#define IPG_TFC_WORDALIGNDISABLED 0x0000000000030000ULL
-#define IPG_TFC_TCPCHECKSUMENABLE 0x0000000000040000ULL
-#define IPG_TFC_UDPCHECKSUMENABLE 0x0000000000080000ULL
-#define IPG_TFC_IPCHECKSUMENABLE 0x0000000000100000ULL
-#define IPG_TFC_FCSAPPENDDISABLE 0x0000000000200000ULL
-#define IPG_TFC_TXINDICATE 0x0000000000400000ULL
-#define IPG_TFC_TXDMAINDICATE 0x0000000000800000ULL
-#define IPG_TFC_FRAGCOUNT 0x000000000F000000ULL
-#define IPG_TFC_VLANTAGINSERT 0x0000000010000000ULL
-#define IPG_TFC_TFDDONE 0x0000000080000000ULL
-#define IPG_TFC_VID 0x00000FFF00000000ULL
-#define IPG_TFC_CFI 0x0000100000000000ULL
-#define IPG_TFC_USERPRIORITY 0x0000E00000000000ULL
-
-/* TFDList, FragInfo */
-#define IPG_TFI_RSVD_MASK 0xFFFF00FFFFFFFFFFULL
-#define IPG_TFI_FRAGADDR 0x000000FFFFFFFFFFULL
-#define IPG_TFI_FRAGLEN 0xFFFF000000000000ULL
-
-/* RFD data structure masks. */
-
-/* RFDList, RFS */
-#define IPG_RFS_RSVD_MASK 0x0000FFFFFFFFFFFFULL
-#define IPG_RFS_RXFRAMELEN 0x000000000000FFFFULL
-#define IPG_RFS_RXFIFOOVERRUN 0x0000000000010000ULL
-#define IPG_RFS_RXRUNTFRAME 0x0000000000020000ULL
-#define IPG_RFS_RXALIGNMENTERROR 0x0000000000040000ULL
-#define IPG_RFS_RXFCSERROR 0x0000000000080000ULL
-#define IPG_RFS_RXOVERSIZEDFRAME 0x0000000000100000ULL
-#define IPG_RFS_RXLENGTHERROR 0x0000000000200000ULL
-#define IPG_RFS_VLANDETECTED 0x0000000000400000ULL
-#define IPG_RFS_TCPDETECTED 0x0000000000800000ULL
-#define IPG_RFS_TCPERROR 0x0000000001000000ULL
-#define IPG_RFS_UDPDETECTED 0x0000000002000000ULL
-#define IPG_RFS_UDPERROR 0x0000000004000000ULL
-#define IPG_RFS_IPDETECTED 0x0000000008000000ULL
-#define IPG_RFS_IPERROR 0x0000000010000000ULL
-#define IPG_RFS_FRAMESTART 0x0000000020000000ULL
-#define IPG_RFS_FRAMEEND 0x0000000040000000ULL
-#define IPG_RFS_RFDDONE 0x0000000080000000ULL
-#define IPG_RFS_TCI 0x0000FFFF00000000ULL
-
-/* RFDList, FragInfo */
-#define IPG_RFI_RSVD_MASK 0xFFFF00FFFFFFFFFFULL
-#define IPG_RFI_FRAGADDR 0x000000FFFFFFFFFFULL
-#define IPG_RFI_FRAGLEN 0xFFFF000000000000ULL
-
-/* I/O Register masks. */
-
-/* RMON Statistics Mask */
-#define IPG_RZ_ALL 0x0FFFFFFF
-
-/* Statistics Mask */
-#define IPG_SM_ALL 0x0FFFFFFF
-#define IPG_SM_OCTETRCVOK_FRAMESRCVDOK 0x00000001
-#define IPG_SM_MCSTOCTETRCVDOK_MCSTFRAMESRCVDOK 0x00000002
-#define IPG_SM_BCSTOCTETRCVDOK_BCSTFRAMESRCVDOK 0x00000004
-#define IPG_SM_RXJUMBOFRAMES 0x00000008
-#define IPG_SM_TCPCHECKSUMERRORS 0x00000010
-#define IPG_SM_IPCHECKSUMERRORS 0x00000020
-#define IPG_SM_UDPCHECKSUMERRORS 0x00000040
-#define IPG_SM_MACCONTROLFRAMESRCVD 0x00000080
-#define IPG_SM_FRAMESTOOLONGERRORS 0x00000100
-#define IPG_SM_INRANGELENGTHERRORS 0x00000200
-#define IPG_SM_FRAMECHECKSEQERRORS 0x00000400
-#define IPG_SM_FRAMESLOSTRXERRORS 0x00000800
-#define IPG_SM_OCTETXMTOK_FRAMESXMTOK 0x00001000
-#define IPG_SM_MCSTOCTETXMTOK_MCSTFRAMESXMTDOK 0x00002000
-#define IPG_SM_BCSTOCTETXMTOK_BCSTFRAMESXMTDOK 0x00004000
-#define IPG_SM_FRAMESWDEFERREDXMT 0x00008000
-#define IPG_SM_LATECOLLISIONS 0x00010000
-#define IPG_SM_MULTICOLFRAMES 0x00020000
-#define IPG_SM_SINGLECOLFRAMES 0x00040000
-#define IPG_SM_TXJUMBOFRAMES 0x00080000
-#define IPG_SM_CARRIERSENSEERRORS 0x00100000
-#define IPG_SM_MACCONTROLFRAMESXMTD 0x00200000
-#define IPG_SM_FRAMESABORTXSCOLLS 0x00400000
-#define IPG_SM_FRAMESWEXDEFERAL 0x00800000
-
-/* Countdown */
-#define IPG_CD_RSVD_MASK 0x0700FFFF
-#define IPG_CD_COUNT 0x0000FFFF
-#define IPG_CD_COUNTDOWNSPEED 0x01000000
-#define IPG_CD_COUNTDOWNMODE 0x02000000
-#define IPG_CD_COUNTINTENABLED 0x04000000
-
-/* TxDMABurstThresh */
-#define IPG_TB_RSVD_MASK 0xFF
-
-/* TxDMAUrgentThresh */
-#define IPG_TU_RSVD_MASK 0xFF
-
-/* TxDMAPollPeriod */
-#define IPG_TP_RSVD_MASK 0xFF
-
-/* RxDMAUrgentThresh */
-#define IPG_RU_RSVD_MASK 0xFF
-
-/* RxDMAPollPeriod */
-#define IPG_RP_RSVD_MASK 0xFF
-
-/* ReceiveMode */
-#define IPG_RM_RSVD_MASK 0x3F
-#define IPG_RM_RECEIVEUNICAST 0x01
-#define IPG_RM_RECEIVEMULTICAST 0x02
-#define IPG_RM_RECEIVEBROADCAST 0x04
-#define IPG_RM_RECEIVEALLFRAMES 0x08
-#define IPG_RM_RECEIVEMULTICASTHASH 0x10
-#define IPG_RM_RECEIVEIPMULTICAST 0x20
-
-/* PhySet */
-#define IPG_PS_MEM_LENB9B 0x01
-#define IPG_PS_MEM_LEN9 0x02
-#define IPG_PS_NON_COMPDET 0x04
-
-/* PhyCtrl */
-#define IPG_PC_RSVD_MASK 0xFF
-#define IPG_PC_MGMTCLK_LO 0x00
-#define IPG_PC_MGMTCLK_HI 0x01
-#define IPG_PC_MGMTCLK 0x01
-#define IPG_PC_MGMTDATA 0x02
-#define IPG_PC_MGMTDIR 0x04
-#define IPG_PC_DUPLEX_POLARITY 0x08
-#define IPG_PC_DUPLEX_STATUS 0x10
-#define IPG_PC_LINK_POLARITY 0x20
-#define IPG_PC_LINK_SPEED 0xC0
-#define IPG_PC_LINK_SPEED_10MBPS 0x40
-#define IPG_PC_LINK_SPEED_100MBPS 0x80
-#define IPG_PC_LINK_SPEED_1000MBPS 0xC0
-
-/* DMACtrl */
-#define IPG_DC_RSVD_MASK 0xC07D9818
-#define IPG_DC_RX_DMA_COMPLETE 0x00000008
-#define IPG_DC_RX_DMA_POLL_NOW 0x00000010
-#define IPG_DC_TX_DMA_COMPLETE 0x00000800
-#define IPG_DC_TX_DMA_POLL_NOW 0x00001000
-#define IPG_DC_TX_DMA_IN_PROG 0x00008000
-#define IPG_DC_RX_EARLY_DISABLE 0x00010000
-#define IPG_DC_MWI_DISABLE 0x00040000
-#define IPG_DC_TX_WRITE_BACK_DISABLE 0x00080000
-#define IPG_DC_TX_BURST_LIMIT 0x00700000
-#define IPG_DC_TARGET_ABORT 0x40000000
-#define IPG_DC_MASTER_ABORT 0x80000000
-
-/* ASICCtrl */
-#define IPG_AC_RSVD_MASK 0x07FFEFF2
-#define IPG_AC_EXP_ROM_SIZE 0x00000002
-#define IPG_AC_PHY_SPEED10 0x00000010
-#define IPG_AC_PHY_SPEED100 0x00000020
-#define IPG_AC_PHY_SPEED1000 0x00000040
-#define IPG_AC_PHY_MEDIA 0x00000080
-#define IPG_AC_FORCED_CFG 0x00000700
-#define IPG_AC_D3RESETDISABLE 0x00000800
-#define IPG_AC_SPEED_UP_MODE 0x00002000
-#define IPG_AC_LED_MODE 0x00004000
-#define IPG_AC_RST_OUT_POLARITY 0x00008000
-#define IPG_AC_GLOBAL_RESET 0x00010000
-#define IPG_AC_RX_RESET 0x00020000
-#define IPG_AC_TX_RESET 0x00040000
-#define IPG_AC_DMA 0x00080000
-#define IPG_AC_FIFO 0x00100000
-#define IPG_AC_NETWORK 0x00200000
-#define IPG_AC_HOST 0x00400000
-#define IPG_AC_AUTO_INIT 0x00800000
-#define IPG_AC_RST_OUT 0x01000000
-#define IPG_AC_INT_REQUEST 0x02000000
-#define IPG_AC_RESET_BUSY 0x04000000
-#define IPG_AC_LED_SPEED 0x08000000
-#define IPG_AC_LED_MODE_BIT_1 0x20000000
-
-/* EepromCtrl */
-#define IPG_EC_RSVD_MASK 0x83FF
-#define IPG_EC_EEPROM_ADDR 0x00FF
-#define IPG_EC_EEPROM_OPCODE 0x0300
-#define IPG_EC_EEPROM_SUBCOMMAD 0x0000
-#define IPG_EC_EEPROM_WRITEOPCODE 0x0100
-#define IPG_EC_EEPROM_READOPCODE 0x0200
-#define IPG_EC_EEPROM_ERASEOPCODE 0x0300
-#define IPG_EC_EEPROM_BUSY 0x8000
-
-/* FIFOCtrl */
-#define IPG_FC_RSVD_MASK 0xC001
-#define IPG_FC_RAM_TEST_MODE 0x0001
-#define IPG_FC_TRANSMITTING 0x4000
-#define IPG_FC_RECEIVING 0x8000
-
-/* TxStatus */
-#define IPG_TS_RSVD_MASK 0xFFFF00DD
-#define IPG_TS_TX_ERROR 0x00000001
-#define IPG_TS_LATE_COLLISION 0x00000004
-#define IPG_TS_TX_MAX_COLL 0x00000008
-#define IPG_TS_TX_UNDERRUN 0x00000010
-#define IPG_TS_TX_IND_REQD 0x00000040
-#define IPG_TS_TX_COMPLETE 0x00000080
-#define IPG_TS_TX_FRAMEID 0xFFFF0000
-
-/* WakeEvent */
-#define IPG_WE_WAKE_PKT_ENABLE 0x01
-#define IPG_WE_MAGIC_PKT_ENABLE 0x02
-#define IPG_WE_LINK_EVT_ENABLE 0x04
-#define IPG_WE_WAKE_POLARITY 0x08
-#define IPG_WE_WAKE_PKT_EVT 0x10
-#define IPG_WE_MAGIC_PKT_EVT 0x20
-#define IPG_WE_LINK_EVT 0x40
-#define IPG_WE_WOL_ENABLE 0x80
-
-/* IntEnable */
-#define IPG_IE_RSVD_MASK 0x1FFE
-#define IPG_IE_HOST_ERROR 0x0002
-#define IPG_IE_TX_COMPLETE 0x0004
-#define IPG_IE_MAC_CTRL_FRAME 0x0008
-#define IPG_IE_RX_COMPLETE 0x0010
-#define IPG_IE_RX_EARLY 0x0020
-#define IPG_IE_INT_REQUESTED 0x0040
-#define IPG_IE_UPDATE_STATS 0x0080
-#define IPG_IE_LINK_EVENT 0x0100
-#define IPG_IE_TX_DMA_COMPLETE 0x0200
-#define IPG_IE_RX_DMA_COMPLETE 0x0400
-#define IPG_IE_RFD_LIST_END 0x0800
-#define IPG_IE_RX_DMA_PRIORITY 0x1000
-
-/* IntStatus */
-#define IPG_IS_RSVD_MASK 0x1FFF
-#define IPG_IS_INTERRUPT_STATUS 0x0001
-#define IPG_IS_HOST_ERROR 0x0002
-#define IPG_IS_TX_COMPLETE 0x0004
-#define IPG_IS_MAC_CTRL_FRAME 0x0008
-#define IPG_IS_RX_COMPLETE 0x0010
-#define IPG_IS_RX_EARLY 0x0020
-#define IPG_IS_INT_REQUESTED 0x0040
-#define IPG_IS_UPDATE_STATS 0x0080
-#define IPG_IS_LINK_EVENT 0x0100
-#define IPG_IS_TX_DMA_COMPLETE 0x0200
-#define IPG_IS_RX_DMA_COMPLETE 0x0400
-#define IPG_IS_RFD_LIST_END 0x0800
-#define IPG_IS_RX_DMA_PRIORITY 0x1000
-
-/* MACCtrl */
-#define IPG_MC_RSVD_MASK 0x7FE33FA3
-#define IPG_MC_IFS_SELECT 0x00000003
-#define IPG_MC_IFS_4352BIT 0x00000003
-#define IPG_MC_IFS_1792BIT 0x00000002
-#define IPG_MC_IFS_1024BIT 0x00000001
-#define IPG_MC_IFS_96BIT 0x00000000
-#define IPG_MC_DUPLEX_SELECT 0x00000020
-#define IPG_MC_DUPLEX_SELECT_FD 0x00000020
-#define IPG_MC_DUPLEX_SELECT_HD 0x00000000
-#define IPG_MC_TX_FLOW_CONTROL_ENABLE 0x00000080
-#define IPG_MC_RX_FLOW_CONTROL_ENABLE 0x00000100
-#define IPG_MC_RCV_FCS 0x00000200
-#define IPG_MC_FIFO_LOOPBACK 0x00000400
-#define IPG_MC_MAC_LOOPBACK 0x00000800
-#define IPG_MC_AUTO_VLAN_TAGGING 0x00001000
-#define IPG_MC_AUTO_VLAN_UNTAGGING 0x00002000
-#define IPG_MC_COLLISION_DETECT 0x00010000
-#define IPG_MC_CARRIER_SENSE 0x00020000
-#define IPG_MC_STATISTICS_ENABLE 0x00200000
-#define IPG_MC_STATISTICS_DISABLE 0x00400000
-#define IPG_MC_STATISTICS_ENABLED 0x00800000
-#define IPG_MC_TX_ENABLE 0x01000000
-#define IPG_MC_TX_DISABLE 0x02000000
-#define IPG_MC_TX_ENABLED 0x04000000
-#define IPG_MC_RX_ENABLE 0x08000000
-#define IPG_MC_RX_DISABLE 0x10000000
-#define IPG_MC_RX_ENABLED 0x20000000
-#define IPG_MC_PAUSED 0x40000000
-
-/*
- * Tune
- */
-
-/* Assign IPG_APPEND_FCS_ON_TX > 0 for auto FCS append on TX. */
-#define IPG_APPEND_FCS_ON_TX 1
-
-/* Assign IPG_APPEND_FCS_ON_TX > 0 for auto FCS strip on RX. */
-#define IPG_STRIP_FCS_ON_RX 1
-
-/* Assign IPG_DROP_ON_RX_ETH_ERRORS > 0 to drop RX frames with
- * Ethernet errors.
- */
-#define IPG_DROP_ON_RX_ETH_ERRORS 1
-
-/* Assign IPG_INSERT_MANUAL_VLAN_TAG > 0 to insert VLAN tags manually
- * (via TFC).
- */
-#define IPG_INSERT_MANUAL_VLAN_TAG 0
-
-/* Assign IPG_ADD_IPCHECKSUM_ON_TX > 0 for auto IP checksum on TX. */
-#define IPG_ADD_IPCHECKSUM_ON_TX 0
-
-/* Assign IPG_ADD_TCPCHECKSUM_ON_TX > 0 for auto TCP checksum on TX.
- * DO NOT USE FOR SILICON REVISIONS B3 AND EARLIER.
- */
-#define IPG_ADD_TCPCHECKSUM_ON_TX 0
-
-/* Assign IPG_ADD_UDPCHECKSUM_ON_TX > 0 for auto UDP checksum on TX.
- * DO NOT USE FOR SILICON REVISIONS B3 AND EARLIER.
- */
-#define IPG_ADD_UDPCHECKSUM_ON_TX 0
-
-/* If inserting VLAN tags manually, assign the IPG_MANUAL_VLAN_xx
- * constants as desired.
- */
-#define IPG_MANUAL_VLAN_VID 0xABC
-#define IPG_MANUAL_VLAN_CFI 0x1
-#define IPG_MANUAL_VLAN_USERPRIORITY 0x5
-
-#define IPG_IO_REG_RANGE 0xFF
-#define IPG_MEM_REG_RANGE 0x154
-#define IPG_DRIVER_NAME "Sundance Technology IPG Triple-Speed Ethernet"
-#define IPG_NIC_PHY_ADDRESS 0x01
-#define IPG_DMALIST_ALIGN_PAD 0x07
-#define IPG_MULTICAST_HASHTABLE_SIZE 0x40
-
-/* Number of milliseconds to wait after issuing a software reset.
- * 0x05 <= IPG_AC_RESETWAIT to account for proper 10Mbps operation.
- */
-#define IPG_AC_RESETWAIT 0x05
-
-/* Number of IPG_AC_RESETWAIT timeperiods before declaring timeout. */
-#define IPG_AC_RESET_TIMEOUT 0x0A
-
-/* Minimum number of nanoseconds used to toggle MDC clock during
- * MII/GMII register access.
- */
-#define IPG_PC_PHYCTRLWAIT_NS 200
-
-#define IPG_TFDLIST_LENGTH 0x100
-
-/* Number of frames between TxDMAComplete interrupt.
- * 0 < IPG_FRAMESBETWEENTXDMACOMPLETES <= IPG_TFDLIST_LENGTH
- */
-#define IPG_FRAMESBETWEENTXDMACOMPLETES 0x1
-
-#define IPG_RFDLIST_LENGTH 0x100
-
-/* Maximum number of RFDs to process per interrupt.
- * 1 < IPG_MAXRFDPROCESS_COUNT < IPG_RFDLIST_LENGTH
- */
-#define IPG_MAXRFDPROCESS_COUNT 0x80
-
-/* Minimum margin between last freed RFD, and current RFD.
- * 1 < IPG_MINUSEDRFDSTOFREE < IPG_RFDLIST_LENGTH
- */
-#define IPG_MINUSEDRFDSTOFREE 0x80
-
-/* specify the jumbo frame maximum size
- * per unit is 0x600 (the rx_buffer size that one RFD can carry)
- */
-#define MAX_JUMBOSIZE 0x8 /* max is 12K */
-
-/* Key register values loaded at driver start up. */
-
-/* TXDMAPollPeriod is specified in 320ns increments.
- *
- * Value Time
- * ---------------------
- * 0x00-0x01 320ns
- * 0x03 ~1us
- * 0x1F ~10us
- * 0xFF ~82us
- */
-#define IPG_TXDMAPOLLPERIOD_VALUE 0x26
-
-/* TxDMAUrgentThresh specifies the minimum amount of
- * data in the transmit FIFO before asserting an
- * urgent transmit DMA request.
- *
- * Value Min TxFIFO occupied space before urgent TX request
- * ---------------------------------------------------------------
- * 0x00-0x04 128 bytes (1024 bits)
- * 0x27 1248 bytes (~10000 bits)
- * 0x30 1536 bytes (12288 bits)
- * 0xFF 8192 bytes (65535 bits)
- */
-#define IPG_TXDMAURGENTTHRESH_VALUE 0x04
-
-/* TxDMABurstThresh specifies the minimum amount of
- * free space in the transmit FIFO before asserting an
- * transmit DMA request.
- *
- * Value Min TxFIFO free space before TX request
- * ----------------------------------------------------
- * 0x00-0x08 256 bytes
- * 0x30 1536 bytes
- * 0xFF 8192 bytes
- */
-#define IPG_TXDMABURSTTHRESH_VALUE 0x30
-
-/* RXDMAPollPeriod is specified in 320ns increments.
- *
- * Value Time
- * ---------------------
- * 0x00-0x01 320ns
- * 0x03 ~1us
- * 0x1F ~10us
- * 0xFF ~82us
- */
-#define IPG_RXDMAPOLLPERIOD_VALUE 0x01
-
-/* RxDMAUrgentThresh specifies the minimum amount of
- * free space within the receive FIFO before asserting
- * a urgent receive DMA request.
- *
- * Value Min RxFIFO free space before urgent RX request
- * ---------------------------------------------------------------
- * 0x00-0x04 128 bytes (1024 bits)
- * 0x27 1248 bytes (~10000 bits)
- * 0x30 1536 bytes (12288 bits)
- * 0xFF 8192 bytes (65535 bits)
- */
-#define IPG_RXDMAURGENTTHRESH_VALUE 0x30
-
-/* RxDMABurstThresh specifies the minimum amount of
- * occupied space within the receive FIFO before asserting
- * a receive DMA request.
- *
- * Value Min TxFIFO free space before TX request
- * ----------------------------------------------------
- * 0x00-0x08 256 bytes
- * 0x30 1536 bytes
- * 0xFF 8192 bytes
- */
-#define IPG_RXDMABURSTTHRESH_VALUE 0x30
-
-/* FlowOnThresh specifies the maximum amount of occupied
- * space in the receive FIFO before a PAUSE frame with
- * maximum pause time transmitted.
- *
- * Value Max RxFIFO occupied space before PAUSE
- * ---------------------------------------------------
- * 0x0000 0 bytes
- * 0x0740 29,696 bytes
- * 0x07FF 32,752 bytes
- */
-#define IPG_FLOWONTHRESH_VALUE 0x0740
-
-/* FlowOffThresh specifies the minimum amount of occupied
- * space in the receive FIFO before a PAUSE frame with
- * zero pause time is transmitted.
- *
- * Value Max RxFIFO occupied space before PAUSE
- * ---------------------------------------------------
- * 0x0000 0 bytes
- * 0x00BF 3056 bytes
- * 0x07FF 32,752 bytes
- */
-#define IPG_FLOWOFFTHRESH_VALUE 0x00BF
-
-/*
- * Miscellaneous macros.
- */
-
-/* Macros for printing debug statements. */
-#ifdef IPG_DEBUG
-# define IPG_DEBUG_MSG(fmt, args...) \
-do { \
- if (0) \
- printk(KERN_DEBUG "IPG: " fmt, ##args); \
-} while (0)
-# define IPG_DDEBUG_MSG(fmt, args...) \
- printk(KERN_DEBUG "IPG: " fmt, ##args)
-# define IPG_DUMPRFDLIST(args) ipg_dump_rfdlist(args)
-# define IPG_DUMPTFDLIST(args) ipg_dump_tfdlist(args)
-#else
-# define IPG_DEBUG_MSG(fmt, args...) \
-do { \
- if (0) \
- printk(KERN_DEBUG "IPG: " fmt, ##args); \
-} while (0)
-# define IPG_DDEBUG_MSG(fmt, args...) \
-do { \
- if (0) \
- printk(KERN_DEBUG "IPG: " fmt, ##args); \
-} while (0)
-# define IPG_DUMPRFDLIST(args)
-# define IPG_DUMPTFDLIST(args)
-#endif
-
-/*
- * End miscellaneous macros.
- */
-
-/* Transmit Frame Descriptor. The IPG supports 15 fragments,
- * however Linux requires only a single fragment. Note, each
- * TFD field is 64 bits wide.
- */
-struct ipg_tx {
- __le64 next_desc;
- __le64 tfc;
- __le64 frag_info;
-};
-
-/* Receive Frame Descriptor. Note, each RFD field is 64 bits wide.
- */
-struct ipg_rx {
- __le64 next_desc;
- __le64 rfs;
- __le64 frag_info;
-};
-
-struct ipg_jumbo {
- int found_start;
- int current_size;
- struct sk_buff *skb;
-};
-
-/* Structure of IPG NIC specific data. */
-struct ipg_nic_private {
- void __iomem *ioaddr;
- struct ipg_tx *txd;
- struct ipg_rx *rxd;
- dma_addr_t txd_map;
- dma_addr_t rxd_map;
- struct sk_buff *tx_buff[IPG_TFDLIST_LENGTH];
- struct sk_buff *rx_buff[IPG_RFDLIST_LENGTH];
- unsigned int tx_current;
- unsigned int tx_dirty;
- unsigned int rx_current;
- unsigned int rx_dirty;
- bool is_jumbo;
- struct ipg_jumbo jumbo;
- unsigned long rxfrag_size;
- unsigned long rxsupport_size;
- unsigned long max_rxframe_size;
- unsigned int rx_buf_sz;
- struct pci_dev *pdev;
- struct net_device *dev;
- struct net_device_stats stats;
- spinlock_t lock;
- int tenmbpsmode;
-
- u16 led_mode;
- u16 station_addr[3]; /* Station Address in EEPROM Reg 0x10..0x12 */
-
- struct mutex mii_mutex;
- struct mii_if_info mii_if;
- int reset_current_tfd;
-#ifdef IPG_DEBUG
- int RFDlistendCount;
- int RFDListCheckedCount;
- int EmptyRFDListCount;
-#endif
- struct delayed_work task;
-};
-
-#endif /* __LINUX_IPG_H */
--
Ondrej Zary

2015-11-15 02:30:45

by Andy Shevchenko

Subject: Re: [PATCH 1/2] dl2k: Add support for IP1000A-based cards

On Sun, Nov 15, 2015 at 12:05 AM, Ondrej Zary
<[email protected]> wrote:
> Add support for IP1000A chips to dl2k driver.
> IP1000A chip looks like a TC9020 with integrated PHY.
>
> This allows IP1000A chips to work reliably because the ipg driver is
> buggy - it loses packets under load and then completely stops
> transmitting data.
>
> Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps.
> Also verified that it does not break D-Link DGE-550T.
>
> Signed-off-by: Ondrej Zary <[email protected]>

Nitpicks below.

> --- a/drivers/net/ethernet/dlink/dl2k.c
> +++ b/drivers/net/ethernet/dlink/dl2k.c
> @@ -253,6 +253,18 @@ rio_probe1 (struct pci_dev *pdev, const struct pci_device_id *ent)
> if (err)
> goto err_out_unmap_rx;
>
> + if (np->chip_id == CHIP_IP1000A &&
> + (np->pdev->revision == 0x40 || np->pdev->revision == 0x41)) {
> + /* PHY magic taken from ipg driver */
> + mii_write(dev, np->phy_addr, 31, 0x0001);
> + mii_write(dev, np->phy_addr, 27, 0x01e0);
> + mii_write(dev, np->phy_addr, 31, 0x0002);
> + mii_write(dev, np->phy_addr, 27, 0xeb8e);
> + mii_write(dev, np->phy_addr, 31, 0x0000);
> + mii_write(dev, np->phy_addr, 30, 0x005e);
> + mii_write(dev, np->phy_addr, 9, 0x0700);

Isn't too many magic numbers?

> + }
> +
> /* Fiber device? */
> np->phy_media = (dr16(ASICCtrl) & PhyMedia) ? 1 : 0;
> np->link_status = 0;
> @@ -361,6 +373,11 @@ parse_eeprom (struct net_device *dev)
> for (i = 0; i < 6; i++)
> dev->dev_addr[i] = psrom->mac_addr[i];
>
> + if (np->chip_id == CHIP_IP1000A) {
> + np->led_mode = psrom->led_mode;
> + return 0;
> + }
> +
> if (np->pdev->vendor != PCI_VENDOR_ID_DLINK) {
> return 0;
> }
> @@ -406,6 +423,28 @@ parse_eeprom (struct net_device *dev)
> return 0;
> }
>
> +static void rio_set_led_mode(struct net_device *dev)
> +{
> + struct netdev_private *np = netdev_priv(dev);
> + void __iomem *ioaddr = np->ioaddr;
> + u32 mode;
> +
> + if (np->chip_id != CHIP_IP1000A)
> + return;
> +
> + mode = dr32(ASICCtrl);
> + mode &= ~(IPG_AC_LED_MODE_BIT_1 | IPG_AC_LED_MODE | IPG_AC_LED_SPEED);
> +
> + if ((np->led_mode & 0x03) > 1)

Isn't "& 0x03) > 1" the same as plain "& 0x02"?

> + mode |= IPG_AC_LED_MODE_BIT_1;
> + if ((np->led_mode & 0x01) == 1)

Hmm… Seems redundant == 1.

> + mode |= IPG_AC_LED_MODE;
> + if ((np->led_mode & 0x08) == 8)

Similar here.

> + mode |= IPG_AC_LED_SPEED;
> +
> + dw32(ASICCtrl, mode);
> +}
> +
> static int
> rio_open (struct net_device *dev)
> {
> @@ -424,6 +463,8 @@ rio_open (struct net_device *dev)
> GlobalReset | DMAReset | FIFOReset | NetworkReset | HostReset);
> mdelay(10);
>
> + rio_set_led_mode(dev);
> +
> /* DebugCtrl bit 4, 5, 9 must set */
> dw32(DebugCtrl, dr32(DebugCtrl) | 0x0230);
>
> @@ -433,9 +474,10 @@ rio_open (struct net_device *dev)
>
> alloc_list (dev);
>
> - /* Get station address */
> - for (i = 0; i < 6; i++)
> - dw8(StationAddr0 + i, dev->dev_addr[i]);
> + /* Set station address */
> + for (i = 0; i < 3; i++)
> + dw16(StationAddr0 + 2 * i,
> + cpu_to_le16(((u16 *)dev->dev_addr)[i]));

Is it specific requirement for new HW? If not, may be another patch
with micro optimizations.

>
> set_multicast (dev);
> if (np->coalesce) {
> @@ -780,6 +822,7 @@ tx_error (struct net_device *dev, int tx_status)
> break;
> mdelay (1);
> }
> + rio_set_led_mode(dev);
> rio_free_tx (dev, 1);
> /* Reset TFDListPtr */
> dw32(TFDListPtr0, np->tx_ring_dma +
> @@ -799,6 +842,7 @@ tx_error (struct net_device *dev, int tx_status)
> break;
> mdelay (1);
> }
> + rio_set_led_mode(dev);
> /* Let TxStartThresh stay default value */
> }
> /* Maximum Collisions */
> @@ -965,6 +1009,7 @@ rio_error (struct net_device *dev, int int_status)
> dev->name, int_status);
> dw16(ASICCtrl + 2, GlobalReset | HostReset);
> mdelay (500);
> + rio_set_led_mode(dev);
> }
> }
>
> diff --git a/drivers/net/ethernet/dlink/dl2k.h b/drivers/net/ethernet/dlink/dl2k.h
> index 23c07b0..8f4f612 100644
> --- a/drivers/net/ethernet/dlink/dl2k.h
> +++ b/drivers/net/ethernet/dlink/dl2k.h
> @@ -211,6 +211,10 @@ enum ASICCtrl_HiWord_bits {
> ResetBusy = 0x0400,
> };
>
> +#define IPG_AC_LED_MODE BIT(14)
> +#define IPG_AC_LED_SPEED BIT(27)
> +#define IPG_AC_LED_MODE_BIT_1 BIT(29)
> +
> /* Transmit Frame Control bits */
> enum TFC_bits {
> DwordAlign = 0x00000000,
> @@ -332,7 +336,10 @@ typedef struct t_SROM {
> u16 asic_ctrl; /* 0x02 */
> u16 sub_vendor_id; /* 0x04 */
> u16 sub_system_id; /* 0x06 */
> - u16 reserved1[12]; /* 0x08-0x1f */
> + u16 pci_base_1; /* 0x08 (IP1000A only) */
> + u16 pci_base_2; /* 0x0a (IP1000A only) */
> + u16 led_mode; /* 0x0c (IP1000A only) */
> + u16 reserved1[9]; /* 0x0e-0x1f */
> u8 mac_addr[6]; /* 0x20-0x25 */
> u8 reserved2[10]; /* 0x26-0x2f */
> u8 sib[204]; /* 0x30-0xfb */
> @@ -397,6 +404,7 @@ struct netdev_private {
> u16 advertising; /* NWay media advertisement */
> u16 negotiate; /* Negotiated media */
> int phy_addr; /* PHY addresses. */
> + u16 led_mode; /* LED mode read from EEPROM (IP1000A only) */
> };
>
> /* The station address location in the EEPROM. */
> @@ -407,10 +415,15 @@ struct netdev_private {
> class_mask of the class are honored during the comparison.
> driver_data Data private to the driver.
> */
> +#define CHIP_IP1000A 1
>
> static const struct pci_device_id rio_pci_tbl[] = {
> {0x1186, 0x4000, PCI_ANY_ID, PCI_ANY_ID, },
> {0x13f0, 0x1021, PCI_ANY_ID, PCI_ANY_ID, },
> + { PCI_VDEVICE(SUNDANCE, 0x1023), CHIP_IP1000A },
> + { PCI_VDEVICE(SUNDANCE, 0x2021), CHIP_IP1000A },
> + { PCI_VDEVICE(DLINK, 0x9021), CHIP_IP1000A },
> + { PCI_VDEVICE(DLINK, 0x4020), CHIP_IP1000A },
> { }
> };
> MODULE_DEVICE_TABLE (pci, rio_pci_tbl);
> --
> Ondrej Zary
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/



--
With Best Regards,
Andy Shevchenko

2015-11-15 10:43:25

by Ondrej Zary

Subject: Re: [PATCH 1/2] dl2k: Add support for IP1000A-based cards

On Sunday 15 November 2015 03:30:25 Andy Shevchenko wrote:
> On Sun, Nov 15, 2015 at 12:05 AM, Ondrej Zary
>
> <[email protected]> wrote:
> > Add support for IP1000A chips to dl2k driver.
> > IP1000A chip looks like a TC9020 with integrated PHY.
> >
> > This allows IP1000A chips to work reliably because the ipg driver is
> > buggy - it loses packets under load and then completely stops
> > transmitting data.
> >
> > Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps.
> > Also verified that it does not break D-Link DGE-550T.
> >
> > Signed-off-by: Ondrej Zary <[email protected]>
>
> Nitpicks below.
>
> > --- a/drivers/net/ethernet/dlink/dl2k.c
> > +++ b/drivers/net/ethernet/dlink/dl2k.c
> > @@ -253,6 +253,18 @@ rio_probe1 (struct pci_dev *pdev, const struct
> > pci_device_id *ent) if (err)
> > goto err_out_unmap_rx;
> >
> > + if (np->chip_id == CHIP_IP1000A &&
> > + (np->pdev->revision == 0x40 || np->pdev->revision == 0x41)) {
> > + /* PHY magic taken from ipg driver */
> > + mii_write(dev, np->phy_addr, 31, 0x0001);
> > + mii_write(dev, np->phy_addr, 27, 0x01e0);
> > + mii_write(dev, np->phy_addr, 31, 0x0002);
> > + mii_write(dev, np->phy_addr, 27, 0xeb8e);
> > + mii_write(dev, np->phy_addr, 31, 0x0000);
> > + mii_write(dev, np->phy_addr, 30, 0x005e);
> > + mii_write(dev, np->phy_addr, 9, 0x0700);
>
> Isn't too many magic numbers?

It's taken from the ipg driver where it was even more cryptic.
I'll try to decode the magic numbers to something readable.

> > + }
> > +
> > /* Fiber device? */
> > np->phy_media = (dr16(ASICCtrl) & PhyMedia) ? 1 : 0;
> > np->link_status = 0;
> > @@ -361,6 +373,11 @@ parse_eeprom (struct net_device *dev)
> > for (i = 0; i < 6; i++)
> > dev->dev_addr[i] = psrom->mac_addr[i];
> >
> > + if (np->chip_id == CHIP_IP1000A) {
> > + np->led_mode = psrom->led_mode;
> > + return 0;
> > + }
> > +
> > if (np->pdev->vendor != PCI_VENDOR_ID_DLINK) {
> > return 0;
> > }
> > @@ -406,6 +423,28 @@ parse_eeprom (struct net_device *dev)
> > return 0;
> > }
> >
> > +static void rio_set_led_mode(struct net_device *dev)
> > +{
> > + struct netdev_private *np = netdev_priv(dev);
> > + void __iomem *ioaddr = np->ioaddr;
> > + u32 mode;
> > +
> > + if (np->chip_id != CHIP_IP1000A)
> > + return;
> > +
> > + mode = dr32(ASICCtrl);
> > + mode &= ~(IPG_AC_LED_MODE_BIT_1 | IPG_AC_LED_MODE |
> > IPG_AC_LED_SPEED); +
> > + if ((np->led_mode & 0x03) > 1)
>
> Isn't "& 0x03) > 1" the same as plain "& 0x02"?

Yes, you're right. It's copied from the ipg driver. I'll fix it.

> > + mode |= IPG_AC_LED_MODE_BIT_1;
> > + if ((np->led_mode & 0x01) == 1)
>
> Hmm… Seems redundant == 1.
>
> > + mode |= IPG_AC_LED_MODE;
> > + if ((np->led_mode & 0x08) == 8)
>
> Similar here.
>
> > + mode |= IPG_AC_LED_SPEED;
> > +
> > + dw32(ASICCtrl, mode);
> > +}
> > +
> > static int
> > rio_open (struct net_device *dev)
> > {
> > @@ -424,6 +463,8 @@ rio_open (struct net_device *dev)
> > GlobalReset | DMAReset | FIFOReset | NetworkReset |
> > HostReset); mdelay(10);
> >
> > + rio_set_led_mode(dev);
> > +
> > /* DebugCtrl bit 4, 5, 9 must set */
> > dw32(DebugCtrl, dr32(DebugCtrl) | 0x0230);
> >
> > @@ -433,9 +474,10 @@ rio_open (struct net_device *dev)
> >
> > alloc_list (dev);
> >
> > - /* Get station address */
> > - for (i = 0; i < 6; i++)
> > - dw8(StationAddr0 + i, dev->dev_addr[i]);
> > + /* Set station address */
> > + for (i = 0; i < 3; i++)
> > + dw16(StationAddr0 + 2 * i,
> > + cpu_to_le16(((u16 *)dev->dev_addr)[i]));
>
> Is it specific requirement for new HW? If not, may be another patch
> with micro optimizations.

Yes, the old method does not work on IP1000A. In fact, even the TC9020
datasheet says: "Access Rule: Word, Double Word". So it was always wrong but
worked anyway until now.

> > set_multicast (dev);
> > if (np->coalesce) {
> > @@ -780,6 +822,7 @@ tx_error (struct net_device *dev, int tx_status)
> > break;
> > mdelay (1);
> > }
> > + rio_set_led_mode(dev);
> > rio_free_tx (dev, 1);
> > /* Reset TFDListPtr */
> > dw32(TFDListPtr0, np->tx_ring_dma +
> > @@ -799,6 +842,7 @@ tx_error (struct net_device *dev, int tx_status)
> > break;
> > mdelay (1);
> > }
> > + rio_set_led_mode(dev);
> > /* Let TxStartThresh stay default value */
> > }
> > /* Maximum Collisions */
> > @@ -965,6 +1009,7 @@ rio_error (struct net_device *dev, int int_status)
> > dev->name, int_status);
> > dw16(ASICCtrl + 2, GlobalReset | HostReset);
> > mdelay (500);
> > + rio_set_led_mode(dev);
> > }
> > }
> >
> > diff --git a/drivers/net/ethernet/dlink/dl2k.h
> > b/drivers/net/ethernet/dlink/dl2k.h index 23c07b0..8f4f612 100644
> > --- a/drivers/net/ethernet/dlink/dl2k.h
> > +++ b/drivers/net/ethernet/dlink/dl2k.h
> > @@ -211,6 +211,10 @@ enum ASICCtrl_HiWord_bits {
> > ResetBusy = 0x0400,
> > };
> >
> > +#define IPG_AC_LED_MODE BIT(14)
> > +#define IPG_AC_LED_SPEED BIT(27)
> > +#define IPG_AC_LED_MODE_BIT_1 BIT(29)
> > +
> > /* Transmit Frame Control bits */
> > enum TFC_bits {
> > DwordAlign = 0x00000000,
> > @@ -332,7 +336,10 @@ typedef struct t_SROM {
> > u16 asic_ctrl; /* 0x02 */
> > u16 sub_vendor_id; /* 0x04 */
> > u16 sub_system_id; /* 0x06 */
> > - u16 reserved1[12]; /* 0x08-0x1f */
> > + u16 pci_base_1; /* 0x08 (IP1000A only) */
> > + u16 pci_base_2; /* 0x0a (IP1000A only) */
> > + u16 led_mode; /* 0x0c (IP1000A only) */
> > + u16 reserved1[9]; /* 0x0e-0x1f */
> > u8 mac_addr[6]; /* 0x20-0x25 */
> > u8 reserved2[10]; /* 0x26-0x2f */
> > u8 sib[204]; /* 0x30-0xfb */
> > @@ -397,6 +404,7 @@ struct netdev_private {
> > u16 advertising; /* NWay media advertisement */
> > u16 negotiate; /* Negotiated media */
> > int phy_addr; /* PHY addresses. */
> > + u16 led_mode; /* LED mode read from EEPROM (IP1000A
> > only) */ };
> >
> > /* The station address location in the EEPROM. */
> > @@ -407,10 +415,15 @@ struct netdev_private {
> > class_mask of the class are honored during the
> > comparison. driver_data Data private to the driver.
> > */
> > +#define CHIP_IP1000A 1
> >
> > static const struct pci_device_id rio_pci_tbl[] = {
> > {0x1186, 0x4000, PCI_ANY_ID, PCI_ANY_ID, },
> > {0x13f0, 0x1021, PCI_ANY_ID, PCI_ANY_ID, },
> > + { PCI_VDEVICE(SUNDANCE, 0x1023), CHIP_IP1000A },
> > + { PCI_VDEVICE(SUNDANCE, 0x2021), CHIP_IP1000A },
> > + { PCI_VDEVICE(DLINK, 0x9021), CHIP_IP1000A },
> > + { PCI_VDEVICE(DLINK, 0x4020), CHIP_IP1000A },
> > { }
> > };
> > MODULE_DEVICE_TABLE (pci, rio_pci_tbl);
> > --
> > Ondrej Zary
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe linux-kernel"
> > in the body of a message to [email protected]
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
> > Please read the FAQ at http://www.tux.org/lkml/


--
Ondrej Zary

2015-11-15 17:59:09

by David Miller

Subject: Re: [PATCH 1/2] dl2k: Add support for IP1000A-based cards

From: Andy Shevchenko <[email protected]>
Date: Sun, 15 Nov 2015 04:30:25 +0200

> On Sun, Nov 15, 2015 at 12:05 AM, Ondrej Zary
>> @@ -433,9 +474,10 @@ rio_open (struct net_device *dev)
>>
>> alloc_list (dev);
>>
>> - /* Get station address */
>> - for (i = 0; i < 6; i++)
>> - dw8(StationAddr0 + i, dev->dev_addr[i]);
>> + /* Set station address */
>> + for (i = 0; i < 3; i++)
>> + dw16(StationAddr0 + 2 * i,
>> + cpu_to_le16(((u16 *)dev->dev_addr)[i]));
>
> Is it specific requirement for new HW? If not, may be another patch
> with micro optimizations.

I absolutely agree, this definitely should not just be blindly copied
over from the other driver.

And if it is a requirement:

1) It must be documented as per why, both in a comment above the loop
and in the commit log message.

2) It must therefore be tested on dl2k chips that worked with the
dl2k driver beforehand to prove that it doesn't break them.

2015-11-15 20:05:12

by Ondrej Zary

Subject: Re: [PATCH 1/2] dl2k: Add support for IP1000A-based cards

On Sunday 15 November 2015 18:59:05 David Miller wrote:
> From: Andy Shevchenko <[email protected]>
> Date: Sun, 15 Nov 2015 04:30:25 +0200
>
> > On Sun, Nov 15, 2015 at 12:05 AM, Ondrej Zary
> >
> >> @@ -433,9 +474,10 @@ rio_open (struct net_device *dev)
> >>
> >> alloc_list (dev);
> >>
> >> - /* Get station address */
> >> - for (i = 0; i < 6; i++)
> >> - dw8(StationAddr0 + i, dev->dev_addr[i]);
> >> + /* Set station address */
> >> + for (i = 0; i < 3; i++)
> >> + dw16(StationAddr0 + 2 * i,
> >> + cpu_to_le16(((u16 *)dev->dev_addr)[i]));
> >
> > Is it specific requirement for new HW? If not, may be another patch
> > with micro optimizations.
>
> I absolutely agree, this definitely should not just be blindly copied
> over from the other driver.
>
> And if it is a requirement:

Yes, it's required. The byte access does not work on IP1000A chips.

> 1) It must be documented as per why, both in a comment above the loop
> and in the commit log message.

OK.

> 2) It must therefore be tested on dl2k chips that worked with the
> dl2k driver beforehand to prove that it doesn't break them.

Tested it with D-Link DGE-550T (chip marked DL-2000, probably rebranded
TC9020) and it works fine.
Even the TC9020 datasheet says: "Access Rule: Word, Double Word". So it was
always wrong but worked anyway.

--
Ondrej Zary

2015-11-15 22:03:42

by David Miller

Subject: Re: [PATCH 1/2] dl2k: Add support for IP1000A-based cards

From: Ondrej Zary <[email protected]>
Date: Sun, 15 Nov 2015 21:04:58 +0100

> Tested it with D-Link DGE-550T (chip marked DL-2000, probably
> rebranded TC9020) and it works fine. Even the TC9020 datasheet
> says: "Access Rule: Word, Double Word". So it was always wrong but
> worked anyway.

Great, thanks for the info.