Add the "seeed" vendor prefix for Seeed Technology Co., Ltd
Website: https://www.seeedstudio.com/
Signed-off-by: Marcin Sloniewski <[email protected]>
Acked-by: Rob Herring <[email protected]>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 9aeab66be85f..7dd03b3e9d3c 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -902,6 +902,8 @@ patternProperties:
description: Schindler
"^seagate,.*":
description: Seagate Technology PLC
+ "^seeed,.*":
+ description: Seeed Technology Co., Ltd
"^seirobotics,.*":
description: Shenzhen SEI Robotics Co., Ltd
"^semtech,.*":
--
2.27.0
Add support for Seeed Studio's stm32mp157c odyssey board.
Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
and carrier board with USB and ETH interfaces, SD card connector,
wifi and BT chip AP6236.
In this patch only basic kernel boot is supported and interfacing
SD card and on-board eMMC.
Signed-off-by: Marcin Sloniewski <[email protected]>
---
Changes in v3:
- fix compilation on tip of stm32-next
due to change in names for pinctrl
- fix deprecated binding for led node
- fix redundant "okay" statuses
- add phy part number for eth in comment
Changes in v2:
- add new odyssey dts to Makefile
arch/arm/boot/dts/Makefile | 3 +-
.../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++
3 files changed, 350 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e6a1cac0bfc7..a3ea2301c82c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1047,7 +1047,8 @@ dtb-$(CONFIG_ARCH_STM32) += \
stm32mp157c-dk2.dtb \
stm32mp157c-ed1.dtb \
stm32mp157c-ev1.dtb \
- stm32mp157c-lxa-mc1.dtb
+ stm32mp157c-lxa-mc1.dtb \
+ stm32mp157c-odyssey.dtb
dtb-$(CONFIG_MACH_SUN4I) += \
sun4i-a10-a1000.dtb \
sun4i-a10-ba10-tvbox.dtb \
diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
new file mode 100644
index 000000000000..935632caddd6
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <[email protected]>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+ model = "Seeed Studio Odyssey-STM32MP157C SOM";
+ compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
+
+ memory@c0000000 {
+ device_type = "memory";
+ reg = <0xc0000000 0x20000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mcuram2: mcuram2@10000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10000000 0x40000>;
+ no-map;
+ };
+
+ vdev0vring0: vdev0vring0@10040000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10040000 0x1000>;
+ no-map;
+ };
+
+ vdev0vring1: vdev0vring1@10041000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10041000 0x1000>;
+ no-map;
+ };
+
+ vdev0buffer: vdev0buffer@10042000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10042000 0x4000>;
+ no-map;
+ };
+
+ mcuram: mcuram@30000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x30000000 0x40000>;
+ no-map;
+ };
+
+ retram: retram@38000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x38000000 0x10000>;
+ no-map;
+ };
+
+ gpu_reserved: gpu@d4000000 {
+ reg = <0xd4000000 0x4000000>;
+ no-map;
+ };
+ };
+
+ led {
+ compatible = "gpio-leds";
+ led-blue {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_HEARTBEAT;
+ gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&gpu {
+ contiguous-area = <&gpu_reserved>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pmic: stpmic@33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ regulators {
+ compatible = "st,stpmic1-regulators";
+ ldo1-supply = <&v3v3>;
+ ldo3-supply = <&vdd_ddr>;
+ ldo6-supply = <&v3v3>;
+ pwr_sw1-supply = <&bst_out>;
+ pwr_sw2-supply = <&bst_out>;
+
+ vddcore: buck1 {
+ regulator-name = "vddcore";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd_ddr: buck2 {
+ regulator-name = "vdd_ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd: buck3 {
+ regulator-name = "vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ st,mask-reset;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ v3v3: buck4 {
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ regulator-initial-mode = <0>;
+ };
+
+ v1v8_audio: ldo1 {
+ regulator-name = "v1v8_audio";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO1 0>;
+ };
+
+ v3v3_hdmi: ldo2 {
+ regulator-name = "v3v3_hdmi";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO2 0>;
+ };
+
+ vtt_ddr: ldo3 {
+ regulator-name = "vtt_ddr";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <750000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ vdd_usb: ldo4 {
+ regulator-name = "vdd_usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ interrupts = <IT_CURLIM_LDO4 0>;
+ };
+
+ vdda: ldo5 {
+ regulator-name = "vdda";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO5 0>;
+ regulator-boot-on;
+ };
+
+ v1v2_hdmi: ldo6 {
+ regulator-name = "v1v2_hdmi";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO6 0>;
+ };
+
+ vref_ddr: vref_ddr {
+ regulator-name = "vref_ddr";
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ bst_out: boost {
+ regulator-name = "bst_out";
+ interrupts = <IT_OCP_BOOST 0>;
+ };
+
+ vbus_otg: pwr_sw1 {
+ regulator-name = "vbus_otg";
+ interrupts = <IT_OCP_OTG 0>;
+ };
+
+ vbus_sw: pwr_sw2 {
+ regulator-name = "vbus_sw";
+ interrupts = <IT_OCP_SWOUT 0>;
+ regulator-active-discharge;
+ };
+ };
+
+ onkey {
+ compatible = "st,stpmic1-onkey";
+ interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+ interrupt-names = "onkey-falling", "onkey-rising";
+ power-off-time-sec = <10>;
+ };
+
+ watchdog {
+ compatible = "st,stpmic1-wdt";
+ status = "disabled";
+ };
+ };
+};
+
+&ipcc {
+ status = "okay";
+};
+
+&iwdg2 {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&m4_rproc {
+ memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+ <&vdev0vring1>, <&vdev0buffer>;
+ mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+ mbox-names = "vq0", "vq1", "shutdown";
+ interrupt-parent = <&exti>;
+ interrupts = <68 1>;
+ status = "okay";
+};
+
+&rng1 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ vqmmc-supply = <&v3v3>;
+ mmc-ddr-3_3v;
+ status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
new file mode 100644
index 000000000000..09edf6afa155
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <[email protected]>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-odyssey-som.dtsi"
+
+/ {
+ model = "Seeed Studio Odyssey-STM32MP157C Board";
+ compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157";
+
+ aliases {
+ ethernet0 = ðernet0;
+ serial0 = &uart4;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rgmii_pins_a>;
+ pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii-id";
+ max-speed = <1000>;
+ phy-handle = <&phy0>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0: ethernet-phy@0 { /* KSZ9031RN */
+ reg = <0>;
+ };
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c1_pins_a>;
+ pinctrl-1 = <&i2c1_sleep_pins_a>;
+ i2c-scl-rising-time-ns = <100>;
+ i2c-scl-falling-time-ns = <7>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+ cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ disable-wp;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+ status = "okay";
+};
+
--
2.27.0
Document device tree bindings of Seeed SoM and carrier board.
Signed-off-by: Marcin Sloniewski <[email protected]>
Acked-by: Rob Herring <[email protected]>
---
Documentation/devicetree/bindings/arm/stm32/stm32.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/stm32/stm32.yaml b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
index 790e6dd48e34..22b9aaa75eee 100644
--- a/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
+++ b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
@@ -39,6 +39,8 @@ properties:
- enum:
- arrow,stm32mp157a-avenger96 # Avenger96
- lxa,stm32mp157c-mc1
+ - seeed,stm32mp157c-odyssey
+ - seeed,stm32mp157c-odyssey-som
- shiratech,stm32mp157a-iot-box # IoT Box
- shiratech,stm32mp157a-stinger96 # Stinger96
- st,stm32mp157c-ed1
--
2.27.0
On 7/21/20 8:53 PM, Marcin Sloniewski wrote:
> Add support for Seeed Studio's stm32mp157c odyssey board.
> Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
> and carrier board with USB and ETH interfaces, SD card connector,
> wifi and BT chip AP6236.
>
> In this patch only basic kernel boot is supported and interfacing
> SD card and on-board eMMC.
>
> Signed-off-by: Marcin Sloniewski <[email protected]>
> ---
>
> Changes in v3:
> - fix compilation on tip of stm32-next
> due to change in names for pinctrl
> - fix deprecated binding for led node
> - fix redundant "okay" statuses
> - add phy part number for eth in comment
You didn't address all my feedback on v2.
> Changes in v2:
> - add new odyssey dts to Makefile
>
> arch/arm/boot/dts/Makefile | 3 +-
> .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
> arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++
> 3 files changed, 350 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index e6a1cac0bfc7..a3ea2301c82c 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1047,7 +1047,8 @@ dtb-$(CONFIG_ARCH_STM32) += \
> stm32mp157c-dk2.dtb \
> stm32mp157c-ed1.dtb \
> stm32mp157c-ev1.dtb \
> - stm32mp157c-lxa-mc1.dtb
> + stm32mp157c-lxa-mc1.dtb \
> + stm32mp157c-odyssey.dtb
> dtb-$(CONFIG_MACH_SUN4I) += \
> sun4i-a10-a1000.dtb \
> sun4i-a10-ba10-tvbox.dtb \
> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> new file mode 100644
> index 000000000000..935632caddd6
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> @@ -0,0 +1,276 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) 2020 Marcin Sloniewski <[email protected]>.
> + */
> +
> +/dts-v1/;
> +
> +#include "stm32mp157.dtsi"
> +#include "stm32mp15xc.dtsi"
> +#include "stm32mp15-pinctrl.dtsi"
> +#include "stm32mp15xxac-pinctrl.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/mfd/st,stpmic1.h>
> +
> +/ {
> + model = "Seeed Studio Odyssey-STM32MP157C SOM";
> + compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
> +
> + memory@c0000000 {
> + device_type = "memory";
> + reg = <0xc0000000 0x20000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + mcuram2: mcuram2@10000000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10000000 0x40000>;
> + no-map;
> + };
> +
> + vdev0vring0: vdev0vring0@10040000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10040000 0x1000>;
> + no-map;
> + };
> +
> + vdev0vring1: vdev0vring1@10041000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10041000 0x1000>;
> + no-map;
> + };
> +
> + vdev0buffer: vdev0buffer@10042000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10042000 0x4000>;
> + no-map;
> + };
> +
> + mcuram: mcuram@30000000 {
> + compatible = "shared-dma-pool";
> + reg = <0x30000000 0x40000>;
> + no-map;
> + };
> +
> + retram: retram@38000000 {
> + compatible = "shared-dma-pool";
> + reg = <0x38000000 0x10000>;
> + no-map;
> + };
> +
> + gpu_reserved: gpu@d4000000 {
> + reg = <0xd4000000 0x4000000>;
> + no-map;
> + };
> + };
> +
> + led {
> + compatible = "gpio-leds";
> + led-blue {
> + color = <LED_COLOR_ID_BLUE>;
> + function = LED_FUNCTION_HEARTBEAT;
> + gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +};
> +
> +&gpu {
> + contiguous-area = <&gpu_reserved>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins_a>;
> + i2c-scl-rising-time-ns = <185>;
> + i2c-scl-falling-time-ns = <20>;
> + status = "okay";
> + /* spare dmas for other usage */
> + /delete-property/dmas;
> + /delete-property/dma-names;
> +
> + pmic: stpmic@33 {
> + compatible = "st,stpmic1";
> + reg = <0x33>;
> + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + regulators {
> + compatible = "st,stpmic1-regulators";
> + ldo1-supply = <&v3v3>;
> + ldo3-supply = <&vdd_ddr>;
> + ldo6-supply = <&v3v3>;
> + pwr_sw1-supply = <&bst_out>;
> + pwr_sw2-supply = <&bst_out>;
> +
> + vddcore: buck1 {
> + regulator-name = "vddcore";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + vdd_ddr: buck2 {
> + regulator-name = "vdd_ddr";
> + regulator-min-microvolt = <1350000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + vdd: buck3 {
> + regulator-name = "vdd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + st,mask-reset;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + v3v3: buck4 {
> + regulator-name = "v3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-over-current-protection;
> + regulator-initial-mode = <0>;
> + };
> +
> + v1v8_audio: ldo1 {
> + regulator-name = "v1v8_audio";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + interrupts = <IT_CURLIM_LDO1 0>;
> + };
> +
> + v3v3_hdmi: ldo2 {
> + regulator-name = "v3v3_hdmi";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + interrupts = <IT_CURLIM_LDO2 0>;
> + };
> +
> + vtt_ddr: ldo3 {
> + regulator-name = "vtt_ddr";
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <750000>;
> + regulator-always-on;
> + regulator-over-current-protection;
> + };
> +
> + vdd_usb: ldo4 {
> + regulator-name = "vdd_usb";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + interrupts = <IT_CURLIM_LDO4 0>;
> + };
> +
> + vdda: ldo5 {
> + regulator-name = "vdda";
> + regulator-min-microvolt = <2900000>;
> + regulator-max-microvolt = <2900000>;
> + interrupts = <IT_CURLIM_LDO5 0>;
> + regulator-boot-on;
> + };
> +
> + v1v2_hdmi: ldo6 {
> + regulator-name = "v1v2_hdmi";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + interrupts = <IT_CURLIM_LDO6 0>;
> + };
> +
> + vref_ddr: vref_ddr {
> + regulator-name = "vref_ddr";
> + regulator-always-on;
> + regulator-over-current-protection;
> + };
> +
> + bst_out: boost {
> + regulator-name = "bst_out";
> + interrupts = <IT_OCP_BOOST 0>;
> + };
> +
> + vbus_otg: pwr_sw1 {
> + regulator-name = "vbus_otg";
> + interrupts = <IT_OCP_OTG 0>;
> + };
> +
> + vbus_sw: pwr_sw2 {
> + regulator-name = "vbus_sw";
> + interrupts = <IT_OCP_SWOUT 0>;
> + regulator-active-discharge;
> + };
> + };
> +
> + onkey {
> + compatible = "st,stpmic1-onkey";
> + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
> + interrupt-names = "onkey-falling", "onkey-rising";
> + power-off-time-sec = <10>;
> + };
> +
> + watchdog {
> + compatible = "st,stpmic1-wdt";
> + status = "disabled";
> + };
> + };
> +};
> +
> +&ipcc {
> + status = "okay";
> +};
> +
> +&iwdg2 {
> + timeout-sec = <32>;
> + status = "okay";
> +};
> +
> +&m4_rproc {
> + memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
> + <&vdev0vring1>, <&vdev0buffer>;
> + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
> + mbox-names = "vq0", "vq1", "shutdown";
> + interrupt-parent = <&exti>;
> + interrupts = <68 1>;
> + status = "okay";
> +};
> +
> +&rng1 {
> + status = "okay";
> +};
> +
> +&rtc {
> + status = "okay";
> +};
> +
> +&sdmmc2 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
> + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
> + non-removable;
> + no-sd;
> + no-sdio;
> + st,neg-edge;
> + bus-width = <4>;
> + vmmc-supply = <&v3v3>;
> + vqmmc-supply = <&v3v3>;
> + mmc-ddr-3_3v;
> + status = "okay";
> +};
> +
> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
> new file mode 100644
> index 000000000000..09edf6afa155
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
> @@ -0,0 +1,72 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) 2020 Marcin Sloniewski <[email protected]>.
> + */
> +
> +/dts-v1/;
> +
> +#include "stm32mp157c-odyssey-som.dtsi"
> +
> +/ {
> + model = "Seeed Studio Odyssey-STM32MP157C Board";
> + compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157";
> +
> + aliases {
> + ethernet0 = ðernet0;
> + serial0 = &uart4;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +};
> +
> +ðernet0 {
> + status = "okay";
> + pinctrl-0 = <ðernet0_rgmii_pins_a>;
> + pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>;
> + pinctrl-names = "default", "sleep";
> + phy-mode = "rgmii-id";
> + max-speed = <1000>;
> + phy-handle = <&phy0>;
> +
> + mdio0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "snps,dwmac-mdio";
> + phy0: ethernet-phy@0 { /* KSZ9031RN */
> + reg = <0>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c1_pins_a>;
> + pinctrl-1 = <&i2c1_sleep_pins_a>;
> + i2c-scl-rising-time-ns = <100>;
> + i2c-scl-falling-time-ns = <7>;
> + status = "okay";
> + /delete-property/dmas;
> + /delete-property/dma-names;
> +};
> +
> +&sdmmc1 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc1_b4_pins_a>;
> + pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> + cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> + disable-wp;
> + st,neg-edge;
> + bus-width = <4>;
> + vmmc-supply = <&v3v3>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart4_pins_a>;
> + status = "okay";
> +};
> +
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Hello Marcin,
On 7/21/20 8:53 PM, Marcin Sloniewski wrote:
> +&sdmmc2 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
> + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
> + non-removable;
> + no-sd;
> + no-sdio;
> + st,neg-edge;
> + bus-width = <4>;
> + vmmc-supply = <&v3v3>;
> + vqmmc-supply = <&v3v3>;
> + mmc-ddr-3_3v;
> + status = "okay";
> +};
Based on the pins muxed, 8 data lines are configured, but the bus width
is set to 4. What is the reason of not setting this property to 8?
Regards,
Christophe Kerello.
Hi Christophe,
> > + pinctrl-names = "default", "opendrain", "sleep";
> > + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
> > + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
> > + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
> > + non-removable;
> > + no-sd;
> > + no-sdio;
> > + st,neg-edge;
> > + bus-width = <4>;
> > + vmmc-supply = <&v3v3>;
> > + vqmmc-supply = <&v3v3>;
> > + mmc-ddr-3_3v;
> > + status = "okay";
> > +};
>
> Based on the pins muxed, 8 data lines are configured, but the bus width
> is set to 4. What is the reason of not setting this property to 8?
Yes, it was workaround, because sdmmc2 interface was working only
with width set to 4. It turned out there was one wrong pin used in
sdmmc2_d47_pins_a.
It will be fixed in v4.
Regards,
Marcin Sloniewski
Hello Ahmad,
First of all thank you very much for your feedback, it was very helpful!
śr., 22 lip 2020 o 08:40 Ahmad Fatoum <[email protected]> napisał(a):
>
> On 7/21/20 8:53 PM, Marcin Sloniewski wrote:
> > Add support for Seeed Studio's stm32mp157c odyssey board.
> > Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
> > and carrier board with USB and ETH interfaces, SD card connector,
> > wifi and BT chip AP6236.
> >
> > In this patch only basic kernel boot is supported and interfacing
> > SD card and on-board eMMC.
> >
> > Signed-off-by: Marcin Sloniewski <[email protected]>
> > ---
> >
> > Changes in v3:
> > - fix compilation on tip of stm32-next
> > due to change in names for pinctrl
> > - fix deprecated binding for led node
> > - fix redundant "okay" statuses
> > - add phy part number for eth in comment
>
> You didn't address all my feedback on v2.
I posted today v4 of the patch-set with further changes.
Regarding watchdog from pmic: when using this watchdog
my board resets even though I feed the watchdog. I'm going to
use the internal watchdog for now and keep in mind that this
could be improved in future.
I changed phy address to 7, indeed you were right about it.
But unfortunately even though I set the address correctly phy
is still missing according to dmesg (I checked datasheet and schematics
the address is surely correct now).
That's something I would like to postpone a little bit as well for now.
>
> > Changes in v2:
> > - add new odyssey dts to Makefile
> >
> > arch/arm/boot/dts/Makefile | 3 +-
> > .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
> > arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++
> > 3 files changed, 350 insertions(+), 1 deletion(-)
> > create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> > create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index e6a1cac0bfc7..a3ea2301c82c 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -1047,7 +1047,8 @@ dtb-$(CONFIG_ARCH_STM32) += \
> > stm32mp157c-dk2.dtb \
> > stm32mp157c-ed1.dtb \
> > stm32mp157c-ev1.dtb \
> > - stm32mp157c-lxa-mc1.dtb
> > + stm32mp157c-lxa-mc1.dtb \
> > + stm32mp157c-odyssey.dtb
> > dtb-$(CONFIG_MACH_SUN4I) += \
> > sun4i-a10-a1000.dtb \
> > sun4i-a10-ba10-tvbox.dtb \
> > diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> > new file mode 100644
> > index 000000000000..935632caddd6
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> > @@ -0,0 +1,276 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> > +/*
> > + * Copyright (C) 2020 Marcin Sloniewski <[email protected]>.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "stm32mp157.dtsi"
> > +#include "stm32mp15xc.dtsi"
> > +#include "stm32mp15-pinctrl.dtsi"
> > +#include "stm32mp15xxac-pinctrl.dtsi"
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/leds/common.h>
> > +#include <dt-bindings/mfd/st,stpmic1.h>
> > +
> > +/ {
> > + model = "Seeed Studio Odyssey-STM32MP157C SOM";
> > + compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
> > +
> > + memory@c0000000 {
> > + device_type = "memory";
> > + reg = <0xc0000000 0x20000000>;
> > + };
> > +
> > + reserved-memory {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges;
> > +
> > + mcuram2: mcuram2@10000000 {
> > + compatible = "shared-dma-pool";
> > + reg = <0x10000000 0x40000>;
> > + no-map;
> > + };
> > +
> > + vdev0vring0: vdev0vring0@10040000 {
> > + compatible = "shared-dma-pool";
> > + reg = <0x10040000 0x1000>;
> > + no-map;
> > + };
> > +
> > + vdev0vring1: vdev0vring1@10041000 {
> > + compatible = "shared-dma-pool";
> > + reg = <0x10041000 0x1000>;
> > + no-map;
> > + };
> > +
> > + vdev0buffer: vdev0buffer@10042000 {
> > + compatible = "shared-dma-pool";
> > + reg = <0x10042000 0x4000>;
> > + no-map;
> > + };
> > +
> > + mcuram: mcuram@30000000 {
> > + compatible = "shared-dma-pool";
> > + reg = <0x30000000 0x40000>;
> > + no-map;
> > + };
> > +
> > + retram: retram@38000000 {
> > + compatible = "shared-dma-pool";
> > + reg = <0x38000000 0x10000>;
> > + no-map;
> > + };
> > +
> > + gpu_reserved: gpu@d4000000 {
> > + reg = <0xd4000000 0x4000000>;
> > + no-map;
> > + };
> > + };
> > +
> > + led {
> > + compatible = "gpio-leds";
> > + led-blue {
> > + color = <LED_COLOR_ID_BLUE>;
> > + function = LED_FUNCTION_HEARTBEAT;
> > + gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "heartbeat";
> > + };
> > + };
> > +};
> > +
> > +&gpu {
> > + contiguous-area = <&gpu_reserved>;
> > + status = "okay";
> > +};
> > +
> > +&i2c2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2c2_pins_a>;
> > + i2c-scl-rising-time-ns = <185>;
> > + i2c-scl-falling-time-ns = <20>;
> > + status = "okay";
> > + /* spare dmas for other usage */
> > + /delete-property/dmas;
> > + /delete-property/dma-names;
> > +
> > + pmic: stpmic@33 {
> > + compatible = "st,stpmic1";
> > + reg = <0x33>;
> > + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > +
> > + regulators {
> > + compatible = "st,stpmic1-regulators";
> > + ldo1-supply = <&v3v3>;
> > + ldo3-supply = <&vdd_ddr>;
> > + ldo6-supply = <&v3v3>;
> > + pwr_sw1-supply = <&bst_out>;
> > + pwr_sw2-supply = <&bst_out>;
> > +
> > + vddcore: buck1 {
> > + regulator-name = "vddcore";
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-always-on;
> > + regulator-initial-mode = <0>;
> > + regulator-over-current-protection;
> > + };
> > +
> > + vdd_ddr: buck2 {
> > + regulator-name = "vdd_ddr";
> > + regulator-min-microvolt = <1350000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-always-on;
> > + regulator-initial-mode = <0>;
> > + regulator-over-current-protection;
> > + };
> > +
> > + vdd: buck3 {
> > + regulator-name = "vdd";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + st,mask-reset;
> > + regulator-initial-mode = <0>;
> > + regulator-over-current-protection;
> > + };
> > +
> > + v3v3: buck4 {
> > + regulator-name = "v3v3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + regulator-over-current-protection;
> > + regulator-initial-mode = <0>;
> > + };
> > +
> > + v1v8_audio: ldo1 {
> > + regulator-name = "v1v8_audio";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-always-on;
> > + interrupts = <IT_CURLIM_LDO1 0>;
> > + };
> > +
> > + v3v3_hdmi: ldo2 {
> > + regulator-name = "v3v3_hdmi";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + interrupts = <IT_CURLIM_LDO2 0>;
> > + };
> > +
> > + vtt_ddr: ldo3 {
> > + regulator-name = "vtt_ddr";
> > + regulator-min-microvolt = <500000>;
> > + regulator-max-microvolt = <750000>;
> > + regulator-always-on;
> > + regulator-over-current-protection;
> > + };
> > +
> > + vdd_usb: ldo4 {
> > + regulator-name = "vdd_usb";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + interrupts = <IT_CURLIM_LDO4 0>;
> > + };
> > +
> > + vdda: ldo5 {
> > + regulator-name = "vdda";
> > + regulator-min-microvolt = <2900000>;
> > + regulator-max-microvolt = <2900000>;
> > + interrupts = <IT_CURLIM_LDO5 0>;
> > + regulator-boot-on;
> > + };
> > +
> > + v1v2_hdmi: ldo6 {
> > + regulator-name = "v1v2_hdmi";
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <1200000>;
> > + regulator-always-on;
> > + interrupts = <IT_CURLIM_LDO6 0>;
> > + };
> > +
> > + vref_ddr: vref_ddr {
> > + regulator-name = "vref_ddr";
> > + regulator-always-on;
> > + regulator-over-current-protection;
> > + };
> > +
> > + bst_out: boost {
> > + regulator-name = "bst_out";
> > + interrupts = <IT_OCP_BOOST 0>;
> > + };
> > +
> > + vbus_otg: pwr_sw1 {
> > + regulator-name = "vbus_otg";
> > + interrupts = <IT_OCP_OTG 0>;
> > + };
> > +
> > + vbus_sw: pwr_sw2 {
> > + regulator-name = "vbus_sw";
> > + interrupts = <IT_OCP_SWOUT 0>;
> > + regulator-active-discharge;
> > + };
> > + };
> > +
> > + onkey {
> > + compatible = "st,stpmic1-onkey";
> > + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
> > + interrupt-names = "onkey-falling", "onkey-rising";
> > + power-off-time-sec = <10>;
> > + };
> > +
> > + watchdog {
> > + compatible = "st,stpmic1-wdt";
> > + status = "disabled";
> > + };
> > + };
> > +};
> > +
> > +&ipcc {
> > + status = "okay";
> > +};
> > +
> > +&iwdg2 {
> > + timeout-sec = <32>;
> > + status = "okay";
> > +};
> > +
> > +&m4_rproc {
> > + memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
> > + <&vdev0vring1>, <&vdev0buffer>;
> > + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
> > + mbox-names = "vq0", "vq1", "shutdown";
> > + interrupt-parent = <&exti>;
> > + interrupts = <68 1>;
> > + status = "okay";
> > +};
> > +
> > +&rng1 {
> > + status = "okay";
> > +};
> > +
> > +&rtc {
> > + status = "okay";
> > +};
> > +
> > +&sdmmc2 {
> > + pinctrl-names = "default", "opendrain", "sleep";
> > + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
> > + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
> > + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
> > + non-removable;
> > + no-sd;
> > + no-sdio;
> > + st,neg-edge;
> > + bus-width = <4>;
> > + vmmc-supply = <&v3v3>;
> > + vqmmc-supply = <&v3v3>;
> > + mmc-ddr-3_3v;
> > + status = "okay";
> > +};
> > +
> > diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
> > new file mode 100644
> > index 000000000000..09edf6afa155
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
> > @@ -0,0 +1,72 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> > +/*
> > + * Copyright (C) 2020 Marcin Sloniewski <[email protected]>.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "stm32mp157c-odyssey-som.dtsi"
> > +
> > +/ {
> > + model = "Seeed Studio Odyssey-STM32MP157C Board";
> > + compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157";
> > +
> > + aliases {
> > + ethernet0 = ðernet0;
> > + serial0 = &uart4;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +};
> > +
> > +ðernet0 {
> > + status = "okay";
> > + pinctrl-0 = <ðernet0_rgmii_pins_a>;
> > + pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>;
> > + pinctrl-names = "default", "sleep";
> > + phy-mode = "rgmii-id";
> > + max-speed = <1000>;
> > + phy-handle = <&phy0>;
> > +
> > + mdio0 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + compatible = "snps,dwmac-mdio";
> > + phy0: ethernet-phy@0 { /* KSZ9031RN */
> > + reg = <0>;
> > + };
> > + };
> > +};
> > +
> > +&i2c1 {
> > + pinctrl-names = "default", "sleep";
> > + pinctrl-0 = <&i2c1_pins_a>;
> > + pinctrl-1 = <&i2c1_sleep_pins_a>;
> > + i2c-scl-rising-time-ns = <100>;
> > + i2c-scl-falling-time-ns = <7>;
> > + status = "okay";
> > + /delete-property/dmas;
> > + /delete-property/dma-names;
> > +};
> > +
> > +&sdmmc1 {
> > + pinctrl-names = "default", "opendrain", "sleep";
> > + pinctrl-0 = <&sdmmc1_b4_pins_a>;
> > + pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> > + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> > + cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> > + disable-wp;
> > + st,neg-edge;
> > + bus-width = <4>;
> > + vmmc-supply = <&v3v3>;
> > + status = "okay";
> > +};
> > +
> > +&uart4 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart4_pins_a>;
> > + status = "okay";
> > +};
> > +
> >
>
> --
> Pengutronix e.K. | |
> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Hi,
On 7/23/20 9:43 PM, Marcin Słoniewski wrote:
> Hello Ahmad,
>
> First of all thank you very much for your feedback, it was very helpful!
>
> śr., 22 lip 2020 o 08:40 Ahmad Fatoum <[email protected]> napisał(a):
>>
>> On 7/21/20 8:53 PM, Marcin Sloniewski wrote:
>>> Add support for Seeed Studio's stm32mp157c odyssey board.
>>> Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
>>> and carrier board with USB and ETH interfaces, SD card connector,
>>> wifi and BT chip AP6236.
>>>
>>> In this patch only basic kernel boot is supported and interfacing
>>> SD card and on-board eMMC.
>>>
>>> Signed-off-by: Marcin Sloniewski <[email protected]>
>>> ---
>>>
>>> Changes in v3:
>>> - fix compilation on tip of stm32-next
>>> due to change in names for pinctrl
>>> - fix deprecated binding for led node
>>> - fix redundant "okay" statuses
>>> - add phy part number for eth in comment
>>
>> You didn't address all my feedback on v2.
> I posted today v4 of the patch-set with further changes.
> Regarding watchdog from pmic: when using this watchdog
> my board resets even though I feed the watchdog. I'm going to
> use the internal watchdog for now and keep in mind that this
> could be improved in future.
Who turns on the watchdog? If it's in the bootloader,
you can't rely on CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED feeding it till
userspace takes over because the stpmic1_wdt doesn't populate
WDOG_HW_RUNNING in status.
> I changed phy address to 7, indeed you were right about it.
> But unfortunately even though I set the address correctly phy
> is still missing according to dmesg (I checked datasheet and schematics
> the address is surely correct now).
> That's something I would like to postpone a little bit as well for now.
You sent out v4 with a phy address of 7 though.
Did you get it working meanwhile?
>
>>
>>> Changes in v2:
>>> - add new odyssey dts to Makefile
>>>
>>> arch/arm/boot/dts/Makefile | 3 +-
>>> .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
>>> arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++
>>> 3 files changed, 350 insertions(+), 1 deletion(-)
>>> create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
>>> create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
>>>
>>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>>> index e6a1cac0bfc7..a3ea2301c82c 100644
>>> --- a/arch/arm/boot/dts/Makefile
>>> +++ b/arch/arm/boot/dts/Makefile
>>> @@ -1047,7 +1047,8 @@ dtb-$(CONFIG_ARCH_STM32) += \
>>> stm32mp157c-dk2.dtb \
>>> stm32mp157c-ed1.dtb \
>>> stm32mp157c-ev1.dtb \
>>> - stm32mp157c-lxa-mc1.dtb
>>> + stm32mp157c-lxa-mc1.dtb \
>>> + stm32mp157c-odyssey.dtb
>>> dtb-$(CONFIG_MACH_SUN4I) += \
>>> sun4i-a10-a1000.dtb \
>>> sun4i-a10-ba10-tvbox.dtb \
>>> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
>>> new file mode 100644
>>> index 000000000000..935632caddd6
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
>>> @@ -0,0 +1,276 @@
>>> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
>>> +/*
>>> + * Copyright (C) 2020 Marcin Sloniewski <[email protected]>.
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "stm32mp157.dtsi"
>>> +#include "stm32mp15xc.dtsi"
>>> +#include "stm32mp15-pinctrl.dtsi"
>>> +#include "stm32mp15xxac-pinctrl.dtsi"
>>> +#include <dt-bindings/gpio/gpio.h>
>>> +#include <dt-bindings/leds/common.h>
>>> +#include <dt-bindings/mfd/st,stpmic1.h>
>>> +
>>> +/ {
>>> + model = "Seeed Studio Odyssey-STM32MP157C SOM";
>>> + compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
>>> +
>>> + memory@c0000000 {
>>> + device_type = "memory";
>>> + reg = <0xc0000000 0x20000000>;
>>> + };
>>> +
>>> + reserved-memory {
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> + ranges;
>>> +
>>> + mcuram2: mcuram2@10000000 {
>>> + compatible = "shared-dma-pool";
>>> + reg = <0x10000000 0x40000>;
>>> + no-map;
>>> + };
>>> +
>>> + vdev0vring0: vdev0vring0@10040000 {
>>> + compatible = "shared-dma-pool";
>>> + reg = <0x10040000 0x1000>;
>>> + no-map;
>>> + };
>>> +
>>> + vdev0vring1: vdev0vring1@10041000 {
>>> + compatible = "shared-dma-pool";
>>> + reg = <0x10041000 0x1000>;
>>> + no-map;
>>> + };
>>> +
>>> + vdev0buffer: vdev0buffer@10042000 {
>>> + compatible = "shared-dma-pool";
>>> + reg = <0x10042000 0x4000>;
>>> + no-map;
>>> + };
>>> +
>>> + mcuram: mcuram@30000000 {
>>> + compatible = "shared-dma-pool";
>>> + reg = <0x30000000 0x40000>;
>>> + no-map;
>>> + };
>>> +
>>> + retram: retram@38000000 {
>>> + compatible = "shared-dma-pool";
>>> + reg = <0x38000000 0x10000>;
>>> + no-map;
>>> + };
>>> +
>>> + gpu_reserved: gpu@d4000000 {
>>> + reg = <0xd4000000 0x4000000>;
>>> + no-map;
>>> + };
>>> + };
>>> +
>>> + led {
>>> + compatible = "gpio-leds";
>>> + led-blue {
>>> + color = <LED_COLOR_ID_BLUE>;
>>> + function = LED_FUNCTION_HEARTBEAT;
>>> + gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
>>> + linux,default-trigger = "heartbeat";
>>> + };
>>> + };
>>> +};
>>> +
>>> +&gpu {
>>> + contiguous-area = <&gpu_reserved>;
>>> + status = "okay";
>>> +};
>>> +
>>> +&i2c2 {
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&i2c2_pins_a>;
>>> + i2c-scl-rising-time-ns = <185>;
>>> + i2c-scl-falling-time-ns = <20>;
>>> + status = "okay";
>>> + /* spare dmas for other usage */
>>> + /delete-property/dmas;
>>> + /delete-property/dma-names;
>>> +
>>> + pmic: stpmic@33 {
>>> + compatible = "st,stpmic1";
>>> + reg = <0x33>;
>>> + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
>>> + interrupt-controller;
>>> + #interrupt-cells = <2>;
>>> +
>>> + regulators {
>>> + compatible = "st,stpmic1-regulators";
>>> + ldo1-supply = <&v3v3>;
>>> + ldo3-supply = <&vdd_ddr>;
>>> + ldo6-supply = <&v3v3>;
>>> + pwr_sw1-supply = <&bst_out>;
>>> + pwr_sw2-supply = <&bst_out>;
>>> +
>>> + vddcore: buck1 {
>>> + regulator-name = "vddcore";
>>> + regulator-min-microvolt = <800000>;
>>> + regulator-max-microvolt = <1350000>;
>>> + regulator-always-on;
>>> + regulator-initial-mode = <0>;
>>> + regulator-over-current-protection;
>>> + };
>>> +
>>> + vdd_ddr: buck2 {
>>> + regulator-name = "vdd_ddr";
>>> + regulator-min-microvolt = <1350000>;
>>> + regulator-max-microvolt = <1350000>;
>>> + regulator-always-on;
>>> + regulator-initial-mode = <0>;
>>> + regulator-over-current-protection;
>>> + };
>>> +
>>> + vdd: buck3 {
>>> + regulator-name = "vdd";
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + regulator-always-on;
>>> + st,mask-reset;
>>> + regulator-initial-mode = <0>;
>>> + regulator-over-current-protection;
>>> + };
>>> +
>>> + v3v3: buck4 {
>>> + regulator-name = "v3v3";
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + regulator-always-on;
>>> + regulator-over-current-protection;
>>> + regulator-initial-mode = <0>;
>>> + };
>>> +
>>> + v1v8_audio: ldo1 {
>>> + regulator-name = "v1v8_audio";
>>> + regulator-min-microvolt = <1800000>;
>>> + regulator-max-microvolt = <1800000>;
>>> + regulator-always-on;
>>> + interrupts = <IT_CURLIM_LDO1 0>;
>>> + };
>>> +
>>> + v3v3_hdmi: ldo2 {
>>> + regulator-name = "v3v3_hdmi";
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + regulator-always-on;
>>> + interrupts = <IT_CURLIM_LDO2 0>;
>>> + };
>>> +
>>> + vtt_ddr: ldo3 {
>>> + regulator-name = "vtt_ddr";
>>> + regulator-min-microvolt = <500000>;
>>> + regulator-max-microvolt = <750000>;
>>> + regulator-always-on;
>>> + regulator-over-current-protection;
>>> + };
>>> +
>>> + vdd_usb: ldo4 {
>>> + regulator-name = "vdd_usb";
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + interrupts = <IT_CURLIM_LDO4 0>;
>>> + };
>>> +
>>> + vdda: ldo5 {
>>> + regulator-name = "vdda";
>>> + regulator-min-microvolt = <2900000>;
>>> + regulator-max-microvolt = <2900000>;
>>> + interrupts = <IT_CURLIM_LDO5 0>;
>>> + regulator-boot-on;
>>> + };
>>> +
>>> + v1v2_hdmi: ldo6 {
>>> + regulator-name = "v1v2_hdmi";
>>> + regulator-min-microvolt = <1200000>;
>>> + regulator-max-microvolt = <1200000>;
>>> + regulator-always-on;
>>> + interrupts = <IT_CURLIM_LDO6 0>;
>>> + };
>>> +
>>> + vref_ddr: vref_ddr {
>>> + regulator-name = "vref_ddr";
>>> + regulator-always-on;
>>> + regulator-over-current-protection;
>>> + };
>>> +
>>> + bst_out: boost {
>>> + regulator-name = "bst_out";
>>> + interrupts = <IT_OCP_BOOST 0>;
>>> + };
>>> +
>>> + vbus_otg: pwr_sw1 {
>>> + regulator-name = "vbus_otg";
>>> + interrupts = <IT_OCP_OTG 0>;
>>> + };
>>> +
>>> + vbus_sw: pwr_sw2 {
>>> + regulator-name = "vbus_sw";
>>> + interrupts = <IT_OCP_SWOUT 0>;
>>> + regulator-active-discharge;
>>> + };
>>> + };
>>> +
>>> + onkey {
>>> + compatible = "st,stpmic1-onkey";
>>> + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
>>> + interrupt-names = "onkey-falling", "onkey-rising";
>>> + power-off-time-sec = <10>;
>>> + };
>>> +
>>> + watchdog {
>>> + compatible = "st,stpmic1-wdt";
>>> + status = "disabled";
>>> + };
>>> + };
>>> +};
>>> +
>>> +&ipcc {
>>> + status = "okay";
>>> +};
>>> +
>>> +&iwdg2 {
>>> + timeout-sec = <32>;
>>> + status = "okay";
>>> +};
>>> +
>>> +&m4_rproc {
>>> + memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
>>> + <&vdev0vring1>, <&vdev0buffer>;
>>> + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
>>> + mbox-names = "vq0", "vq1", "shutdown";
>>> + interrupt-parent = <&exti>;
>>> + interrupts = <68 1>;
>>> + status = "okay";
>>> +};
>>> +
>>> +&rng1 {
>>> + status = "okay";
>>> +};
>>> +
>>> +&rtc {
>>> + status = "okay";
>>> +};
>>> +
>>> +&sdmmc2 {
>>> + pinctrl-names = "default", "opendrain", "sleep";
>>> + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
>>> + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
>>> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
>>> + non-removable;
>>> + no-sd;
>>> + no-sdio;
>>> + st,neg-edge;
>>> + bus-width = <4>;
>>> + vmmc-supply = <&v3v3>;
>>> + vqmmc-supply = <&v3v3>;
>>> + mmc-ddr-3_3v;
>>> + status = "okay";
>>> +};
>>> +
>>> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
>>> new file mode 100644
>>> index 000000000000..09edf6afa155
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
>>> @@ -0,0 +1,72 @@
>>> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
>>> +/*
>>> + * Copyright (C) 2020 Marcin Sloniewski <[email protected]>.
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "stm32mp157c-odyssey-som.dtsi"
>>> +
>>> +/ {
>>> + model = "Seeed Studio Odyssey-STM32MP157C Board";
>>> + compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157";
>>> +
>>> + aliases {
>>> + ethernet0 = ðernet0;
>>> + serial0 = &uart4;
>>> + };
>>> +
>>> + chosen {
>>> + stdout-path = "serial0:115200n8";
>>> + };
>>> +};
>>> +
>>> +ðernet0 {
>>> + status = "okay";
>>> + pinctrl-0 = <ðernet0_rgmii_pins_a>;
>>> + pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>;
>>> + pinctrl-names = "default", "sleep";
>>> + phy-mode = "rgmii-id";
>>> + max-speed = <1000>;
>>> + phy-handle = <&phy0>;
>>> +
>>> + mdio0 {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> + compatible = "snps,dwmac-mdio";
>>> + phy0: ethernet-phy@0 { /* KSZ9031RN */
>>> + reg = <0>;
>>> + };
>>> + };
>>> +};
>>> +
>>> +&i2c1 {
>>> + pinctrl-names = "default", "sleep";
>>> + pinctrl-0 = <&i2c1_pins_a>;
>>> + pinctrl-1 = <&i2c1_sleep_pins_a>;
>>> + i2c-scl-rising-time-ns = <100>;
>>> + i2c-scl-falling-time-ns = <7>;
>>> + status = "okay";
>>> + /delete-property/dmas;
>>> + /delete-property/dma-names;
>>> +};
>>> +
>>> +&sdmmc1 {
>>> + pinctrl-names = "default", "opendrain", "sleep";
>>> + pinctrl-0 = <&sdmmc1_b4_pins_a>;
>>> + pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
>>> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
>>> + cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
>>> + disable-wp;
>>> + st,neg-edge;
>>> + bus-width = <4>;
>>> + vmmc-supply = <&v3v3>;
>>> + status = "okay";
>>> +};
>>> +
>>> +&uart4 {
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&uart4_pins_a>;
>>> + status = "okay";
>>> +};
>>> +
>>>
>>
>> --
>> Pengutronix e.K. | |
>> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
>> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
>> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Hi,
pt., 24 lip 2020 o 11:17 Ahmad Fatoum <[email protected]> napisał(a):
>
> Hi,
>
> On 7/23/20 9:43 PM, Marcin Słoniewski wrote:
> > Hello Ahmad,
> >
> > First of all thank you very much for your feedback, it was very helpful!
> >
> > śr., 22 lip 2020 o 08:40 Ahmad Fatoum <[email protected]> napisał(a):
> >>
> >> On 7/21/20 8:53 PM, Marcin Sloniewski wrote:
> >>> Add support for Seeed Studio's stm32mp157c odyssey board.
> >>> Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
> >>> and carrier board with USB and ETH interfaces, SD card connector,
> >>> wifi and BT chip AP6236.
> >>>
> >>> In this patch only basic kernel boot is supported and interfacing
> >>> SD card and on-board eMMC.
> >>>
> >>> Signed-off-by: Marcin Sloniewski <[email protected]>
> >>> ---
> >>>
> >>> Changes in v3:
> >>> - fix compilation on tip of stm32-next
> >>> due to change in names for pinctrl
> >>> - fix deprecated binding for led node
> >>> - fix redundant "okay" statuses
> >>> - add phy part number for eth in comment
> >>
> >> You didn't address all my feedback on v2.
> > I posted today v4 of the patch-set with further changes.
> > Regarding watchdog from pmic: when using this watchdog
> > my board resets even though I feed the watchdog. I'm going to
> > use the internal watchdog for now and keep in mind that this
> > could be improved in future.
>
> Who turns on the watchdog? If it's in the bootloader,
> you can't rely on CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED feeding it till
> userspace takes over because the stpmic1_wdt doesn't populate
> WDOG_HW_RUNNING in status.
It's not turned on in bootloader (u-boot). I'm able to boot to userspace, but
the watchdog reboots board when using busybox's watchdog demon and when
I'm manually feeding it. Every other stm32mp1 based board isn't using
pmic watchdog,
so I guess it can be replaced by internal watchdog for now?
>
> > I changed phy address to 7, indeed you were right about it.
> > But unfortunately even though I set the address correctly phy
> > is still missing according to dmesg (I checked datasheet and schematics
> > the address is surely correct now).
> > That's something I would like to postpone a little bit as well for now.
>
> You sent out v4 with a phy address of 7 though.
> Did you get it working meanwhile?
Unfortunately not yet.
>
> >
> >>
> >>> Changes in v2:
> >>> - add new odyssey dts to Makefile
> >>>
> >>> arch/arm/boot/dts/Makefile | 3 +-
> >>> .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
> >>> arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++
> >>> 3 files changed, 350 insertions(+), 1 deletion(-)
> >>> create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> >>> create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
> >>>
> >>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> >>> index e6a1cac0bfc7..a3ea2301c82c 100644
> >>> --- a/arch/arm/boot/dts/Makefile
> >>> +++ b/arch/arm/boot/dts/Makefile
> >>> @@ -1047,7 +1047,8 @@ dtb-$(CONFIG_ARCH_STM32) += \
> >>> stm32mp157c-dk2.dtb \
> >>> stm32mp157c-ed1.dtb \
> >>> stm32mp157c-ev1.dtb \
> >>> - stm32mp157c-lxa-mc1.dtb
> >>> + stm32mp157c-lxa-mc1.dtb \
> >>> + stm32mp157c-odyssey.dtb
> >>> dtb-$(CONFIG_MACH_SUN4I) += \
> >>> sun4i-a10-a1000.dtb \
> >>> sun4i-a10-ba10-tvbox.dtb \
> >>> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> >>> new file mode 100644
> >>> index 000000000000..935632caddd6
> >>> --- /dev/null
> >>> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> >>> @@ -0,0 +1,276 @@
> >>> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> >>> +/*
> >>> + * Copyright (C) 2020 Marcin Sloniewski <[email protected]>.
> >>> + */
> >>> +
> >>> +/dts-v1/;
> >>> +
> >>> +#include "stm32mp157.dtsi"
> >>> +#include "stm32mp15xc.dtsi"
> >>> +#include "stm32mp15-pinctrl.dtsi"
> >>> +#include "stm32mp15xxac-pinctrl.dtsi"
> >>> +#include <dt-bindings/gpio/gpio.h>
> >>> +#include <dt-bindings/leds/common.h>
> >>> +#include <dt-bindings/mfd/st,stpmic1.h>
> >>> +
> >>> +/ {
> >>> + model = "Seeed Studio Odyssey-STM32MP157C SOM";
> >>> + compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
> >>> +
> >>> + memory@c0000000 {
> >>> + device_type = "memory";
> >>> + reg = <0xc0000000 0x20000000>;
> >>> + };
> >>> +
> >>> + reserved-memory {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <1>;
> >>> + ranges;
> >>> +
> >>> + mcuram2: mcuram2@10000000 {
> >>> + compatible = "shared-dma-pool";
> >>> + reg = <0x10000000 0x40000>;
> >>> + no-map;
> >>> + };
> >>> +
> >>> + vdev0vring0: vdev0vring0@10040000 {
> >>> + compatible = "shared-dma-pool";
> >>> + reg = <0x10040000 0x1000>;
> >>> + no-map;
> >>> + };
> >>> +
> >>> + vdev0vring1: vdev0vring1@10041000 {
> >>> + compatible = "shared-dma-pool";
> >>> + reg = <0x10041000 0x1000>;
> >>> + no-map;
> >>> + };
> >>> +
> >>> + vdev0buffer: vdev0buffer@10042000 {
> >>> + compatible = "shared-dma-pool";
> >>> + reg = <0x10042000 0x4000>;
> >>> + no-map;
> >>> + };
> >>> +
> >>> + mcuram: mcuram@30000000 {
> >>> + compatible = "shared-dma-pool";
> >>> + reg = <0x30000000 0x40000>;
> >>> + no-map;
> >>> + };
> >>> +
> >>> + retram: retram@38000000 {
> >>> + compatible = "shared-dma-pool";
> >>> + reg = <0x38000000 0x10000>;
> >>> + no-map;
> >>> + };
> >>> +
> >>> + gpu_reserved: gpu@d4000000 {
> >>> + reg = <0xd4000000 0x4000000>;
> >>> + no-map;
> >>> + };
> >>> + };
> >>> +
> >>> + led {
> >>> + compatible = "gpio-leds";
> >>> + led-blue {
> >>> + color = <LED_COLOR_ID_BLUE>;
> >>> + function = LED_FUNCTION_HEARTBEAT;
> >>> + gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
> >>> + linux,default-trigger = "heartbeat";
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&gpu {
> >>> + contiguous-area = <&gpu_reserved>;
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&i2c2 {
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&i2c2_pins_a>;
> >>> + i2c-scl-rising-time-ns = <185>;
> >>> + i2c-scl-falling-time-ns = <20>;
> >>> + status = "okay";
> >>> + /* spare dmas for other usage */
> >>> + /delete-property/dmas;
> >>> + /delete-property/dma-names;
> >>> +
> >>> + pmic: stpmic@33 {
> >>> + compatible = "st,stpmic1";
> >>> + reg = <0x33>;
> >>> + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
> >>> + interrupt-controller;
> >>> + #interrupt-cells = <2>;
> >>> +
> >>> + regulators {
> >>> + compatible = "st,stpmic1-regulators";
> >>> + ldo1-supply = <&v3v3>;
> >>> + ldo3-supply = <&vdd_ddr>;
> >>> + ldo6-supply = <&v3v3>;
> >>> + pwr_sw1-supply = <&bst_out>;
> >>> + pwr_sw2-supply = <&bst_out>;
> >>> +
> >>> + vddcore: buck1 {
> >>> + regulator-name = "vddcore";
> >>> + regulator-min-microvolt = <800000>;
> >>> + regulator-max-microvolt = <1350000>;
> >>> + regulator-always-on;
> >>> + regulator-initial-mode = <0>;
> >>> + regulator-over-current-protection;
> >>> + };
> >>> +
> >>> + vdd_ddr: buck2 {
> >>> + regulator-name = "vdd_ddr";
> >>> + regulator-min-microvolt = <1350000>;
> >>> + regulator-max-microvolt = <1350000>;
> >>> + regulator-always-on;
> >>> + regulator-initial-mode = <0>;
> >>> + regulator-over-current-protection;
> >>> + };
> >>> +
> >>> + vdd: buck3 {
> >>> + regulator-name = "vdd";
> >>> + regulator-min-microvolt = <3300000>;
> >>> + regulator-max-microvolt = <3300000>;
> >>> + regulator-always-on;
> >>> + st,mask-reset;
> >>> + regulator-initial-mode = <0>;
> >>> + regulator-over-current-protection;
> >>> + };
> >>> +
> >>> + v3v3: buck4 {
> >>> + regulator-name = "v3v3";
> >>> + regulator-min-microvolt = <3300000>;
> >>> + regulator-max-microvolt = <3300000>;
> >>> + regulator-always-on;
> >>> + regulator-over-current-protection;
> >>> + regulator-initial-mode = <0>;
> >>> + };
> >>> +
> >>> + v1v8_audio: ldo1 {
> >>> + regulator-name = "v1v8_audio";
> >>> + regulator-min-microvolt = <1800000>;
> >>> + regulator-max-microvolt = <1800000>;
> >>> + regulator-always-on;
> >>> + interrupts = <IT_CURLIM_LDO1 0>;
> >>> + };
> >>> +
> >>> + v3v3_hdmi: ldo2 {
> >>> + regulator-name = "v3v3_hdmi";
> >>> + regulator-min-microvolt = <3300000>;
> >>> + regulator-max-microvolt = <3300000>;
> >>> + regulator-always-on;
> >>> + interrupts = <IT_CURLIM_LDO2 0>;
> >>> + };
> >>> +
> >>> + vtt_ddr: ldo3 {
> >>> + regulator-name = "vtt_ddr";
> >>> + regulator-min-microvolt = <500000>;
> >>> + regulator-max-microvolt = <750000>;
> >>> + regulator-always-on;
> >>> + regulator-over-current-protection;
> >>> + };
> >>> +
> >>> + vdd_usb: ldo4 {
> >>> + regulator-name = "vdd_usb";
> >>> + regulator-min-microvolt = <3300000>;
> >>> + regulator-max-microvolt = <3300000>;
> >>> + interrupts = <IT_CURLIM_LDO4 0>;
> >>> + };
> >>> +
> >>> + vdda: ldo5 {
> >>> + regulator-name = "vdda";
> >>> + regulator-min-microvolt = <2900000>;
> >>> + regulator-max-microvolt = <2900000>;
> >>> + interrupts = <IT_CURLIM_LDO5 0>;
> >>> + regulator-boot-on;
> >>> + };
> >>> +
> >>> + v1v2_hdmi: ldo6 {
> >>> + regulator-name = "v1v2_hdmi";
> >>> + regulator-min-microvolt = <1200000>;
> >>> + regulator-max-microvolt = <1200000>;
> >>> + regulator-always-on;
> >>> + interrupts = <IT_CURLIM_LDO6 0>;
> >>> + };
> >>> +
> >>> + vref_ddr: vref_ddr {
> >>> + regulator-name = "vref_ddr";
> >>> + regulator-always-on;
> >>> + regulator-over-current-protection;
> >>> + };
> >>> +
> >>> + bst_out: boost {
> >>> + regulator-name = "bst_out";
> >>> + interrupts = <IT_OCP_BOOST 0>;
> >>> + };
> >>> +
> >>> + vbus_otg: pwr_sw1 {
> >>> + regulator-name = "vbus_otg";
> >>> + interrupts = <IT_OCP_OTG 0>;
> >>> + };
> >>> +
> >>> + vbus_sw: pwr_sw2 {
> >>> + regulator-name = "vbus_sw";
> >>> + interrupts = <IT_OCP_SWOUT 0>;
> >>> + regulator-active-discharge;
> >>> + };
> >>> + };
> >>> +
> >>> + onkey {
> >>> + compatible = "st,stpmic1-onkey";
> >>> + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
> >>> + interrupt-names = "onkey-falling", "onkey-rising";
> >>> + power-off-time-sec = <10>;
> >>> + };
> >>> +
> >>> + watchdog {
> >>> + compatible = "st,stpmic1-wdt";
> >>> + status = "disabled";
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&ipcc {
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&iwdg2 {
> >>> + timeout-sec = <32>;
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&m4_rproc {
> >>> + memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
> >>> + <&vdev0vring1>, <&vdev0buffer>;
> >>> + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
> >>> + mbox-names = "vq0", "vq1", "shutdown";
> >>> + interrupt-parent = <&exti>;
> >>> + interrupts = <68 1>;
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&rng1 {
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&rtc {
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&sdmmc2 {
> >>> + pinctrl-names = "default", "opendrain", "sleep";
> >>> + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
> >>> + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
> >>> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
> >>> + non-removable;
> >>> + no-sd;
> >>> + no-sdio;
> >>> + st,neg-edge;
> >>> + bus-width = <4>;
> >>> + vmmc-supply = <&v3v3>;
> >>> + vqmmc-supply = <&v3v3>;
> >>> + mmc-ddr-3_3v;
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
> >>> new file mode 100644
> >>> index 000000000000..09edf6afa155
> >>> --- /dev/null
> >>> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
> >>> @@ -0,0 +1,72 @@
> >>> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> >>> +/*
> >>> + * Copyright (C) 2020 Marcin Sloniewski <[email protected]>.
> >>> + */
> >>> +
> >>> +/dts-v1/;
> >>> +
> >>> +#include "stm32mp157c-odyssey-som.dtsi"
> >>> +
> >>> +/ {
> >>> + model = "Seeed Studio Odyssey-STM32MP157C Board";
> >>> + compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157";
> >>> +
> >>> + aliases {
> >>> + ethernet0 = ðernet0;
> >>> + serial0 = &uart4;
> >>> + };
> >>> +
> >>> + chosen {
> >>> + stdout-path = "serial0:115200n8";
> >>> + };
> >>> +};
> >>> +
> >>> +ðernet0 {
> >>> + status = "okay";
> >>> + pinctrl-0 = <ðernet0_rgmii_pins_a>;
> >>> + pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>;
> >>> + pinctrl-names = "default", "sleep";
> >>> + phy-mode = "rgmii-id";
> >>> + max-speed = <1000>;
> >>> + phy-handle = <&phy0>;
> >>> +
> >>> + mdio0 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + compatible = "snps,dwmac-mdio";
> >>> + phy0: ethernet-phy@0 { /* KSZ9031RN */
> >>> + reg = <0>;
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&i2c1 {
> >>> + pinctrl-names = "default", "sleep";
> >>> + pinctrl-0 = <&i2c1_pins_a>;
> >>> + pinctrl-1 = <&i2c1_sleep_pins_a>;
> >>> + i2c-scl-rising-time-ns = <100>;
> >>> + i2c-scl-falling-time-ns = <7>;
> >>> + status = "okay";
> >>> + /delete-property/dmas;
> >>> + /delete-property/dma-names;
> >>> +};
> >>> +
> >>> +&sdmmc1 {
> >>> + pinctrl-names = "default", "opendrain", "sleep";
> >>> + pinctrl-0 = <&sdmmc1_b4_pins_a>;
> >>> + pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> >>> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> >>> + cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> >>> + disable-wp;
> >>> + st,neg-edge;
> >>> + bus-width = <4>;
> >>> + vmmc-supply = <&v3v3>;
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&uart4 {
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&uart4_pins_a>;
> >>> + status = "okay";
> >>> +};
> >>> +
> >>>
> >>
> >> --
> >> Pengutronix e.K. | |
> >> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
> >> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> >> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
> >
>
> --
> Pengutronix e.K. | |
> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |