The WaRP Board is a Wearable Reference Plaform. The board features:
- Freescale i.MX6 SoloLite processor with 512MB of RAM
- Freescale FXOS8700CQ 6-axis Xtrinsic sensor
- Freescale Kinetis KL16 MCU
- Freescale Xtrinsic MMA955xL intelligent motion sensing platform
The board implements a hybrid architecture to address the evolving
needs of the wearables market. The platform consists of a main board
and an example daughtercard with the ability to add additional
daughtercards for different usage models.
For more information about the project, visit:
http://www.warpboard.org/
Signed-off-by: Otavio Salvador <[email protected]>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/imx6sl-warp.dts | 154 ++++++++++++++++++++++++++++++++++++++
2 files changed, 156 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/imx6sl-warp.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a1c776b..1b49d57 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -299,7 +299,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-wandboard.dtb \
imx6q-wandboard-revb1.dtb
dtb-$(CONFIG_SOC_IMX6SL) += \
- imx6sl-evk.dtb
+ imx6sl-evk.dtb \
+ imx6sl-warp.dtb
dtb-$(CONFIG_SOC_IMX6SX) += \
imx6sx-sabreauto.dtb \
imx6sx-sdb.dtb
diff --git a/arch/arm/boot/dts/imx6sl-warp.dts b/arch/arm/boot/dts/imx6sl-warp.dts
new file mode 100644
index 0000000..dadb92f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6sl-warp.dts
@@ -0,0 +1,154 @@
+/*
+ * Copyright 2014, 2015 O.S. Systems Software LTDA.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+
+#include "imx6sl.dtsi"
+
+/ {
+ model = "WaRP Board";
+ compatible = "warp,imx6sl-warp", "fsl,imx6sl";
+
+ memory {
+ reg = <0x80000000 0x20000000>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_usb_otg1_vbus: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 0 0>;
+ enable-active-high;
+ };
+
+ reg_usb_otg2_vbus: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "usb_otg2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 2 0>;
+ enable-active-high;
+ };
+
+ reg_1p8v: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "1P8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&usbotg1 {
+ vbus-supply = <®_usb_otg1_vbus>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg2 {
+ vbus-supply = <®_usb_otg2_vbus>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ non-removable;
+ status = "okay";
+};
+
+&iomuxc {
+ imx6sl-warp {
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x41b0b1
+ MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x41b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6SL_PAD_AUD_RXC__UART3_RX_DATA 0x41b0b1
+ MX6SL_PAD_AUD_RXC__UART3_TX_DATA 0x41b0b1
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6SL_PAD_SD2_CMD__SD2_CMD 0x417059
+ MX6SL_PAD_SD2_CLK__SD2_CLK 0x410059
+ MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x417059
+ MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x417059
+ MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x417059
+ MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x417059
+ MX6SL_PAD_SD2_DAT4__SD2_DATA4 0x417059
+ MX6SL_PAD_SD2_DAT5__SD2_DATA5 0x417059
+ MX6SL_PAD_SD2_DAT6__SD2_DATA6 0x417059
+ MX6SL_PAD_SD2_DAT7__SD2_DATA7 0x417059
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX6SL_PAD_SD2_CMD__SD2_CMD 0x4170b9
+ MX6SL_PAD_SD2_CLK__SD2_CLK 0x4100b9
+ MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x4170b9
+ MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x4170b9
+ MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x4170b9
+ MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x4170b9
+ MX6SL_PAD_SD2_DAT4__SD2_DATA4 0x4170b9
+ MX6SL_PAD_SD2_DAT5__SD2_DATA5 0x4170b9
+ MX6SL_PAD_SD2_DAT6__SD2_DATA6 0x4170b9
+ MX6SL_PAD_SD2_DAT7__SD2_DATA7 0x4170b9
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX6SL_PAD_SD2_CMD__SD2_CMD 0x4170f9
+ MX6SL_PAD_SD2_CLK__SD2_CLK 0x4100f9
+ MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x4170f9
+ MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x4170f9
+ MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x4170f9
+ MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x4170f9
+ MX6SL_PAD_SD2_DAT4__SD2_DATA4 0x4170f9
+ MX6SL_PAD_SD2_DAT5__SD2_DATA5 0x4170f9
+ MX6SL_PAD_SD2_DAT6__SD2_DATA6 0x4170f9
+ MX6SL_PAD_SD2_DAT7__SD2_DATA7 0x4170f9
+ >;
+ };
+ };
+};
--
2.1.4
On Wed, Feb 25, 2015 at 2:02 PM, Otavio Salvador
<[email protected]> wrote:
> The WaRP Board is a Wearable Reference Plaform. The board features:
>
> - Freescale i.MX6 SoloLite processor with 512MB of RAM
> - Freescale FXOS8700CQ 6-axis Xtrinsic sensor
> - Freescale Kinetis KL16 MCU
> - Freescale Xtrinsic MMA955xL intelligent motion sensing platform
>
> The board implements a hybrid architecture to address the evolving
> needs of the wearables market. The platform consists of a main board
> and an example daughtercard with the ability to add additional
> daughtercards for different usage models.
>
> For more information about the project, visit:
>
> http://www.warpboard.org/
>
> Signed-off-by: Otavio Salvador <[email protected]>
Thanks, Otavio. It boots well on my warp, so:
Tested-by: Fabio Estevam <[email protected]>