by Pawel Laszczak

[permalink] [raw]

Subject: RE: [PATCH 7/8] usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver

>
>On Mon, 2020-09-28 at 14:27 +0200, Pawel Laszczak wrote:
>> This patch introduces the main part of Cadence USBSSP DRD driver
>> to Linux kernel.
>> To reduce the patch size a little bit, the header file gadget.h was
>> intentionally added as separate patch.
>>
>> The Cadence USBSSP DRD Controller is a highly configurable IP Core which
>> can be instantiated as Dual-Role Device (DRD), Peripheral Only and
>> Host Only (XHCI)configurations.
>>
>> The current driver has been validated with FPGA platform. We have
>> support for PCIe bus, which is used on FPGA prototyping.
>>
>> The host side of USBSS DRD controller is compliant with XHCI.
>> The architecture for device side is almost the same as for host side,
>> and most of the XHCI specification can be used to understand how
>> this controller operates.
>>
>> Signed-off-by: Pawel Laszczak <[email protected]>
>> ---
>> drivers/usb/Kconfig | 1 +
>> drivers/usb/Makefile | 1 +
>> drivers/usb/cdns3/core.c | 19 +-
>> drivers/usb/cdns3/drd.c | 28 +
>> drivers/usb/cdns3/drd.h | 2 +
>> drivers/usb/cdns3/gadget-export.h | 18 +-
>> drivers/usb/cdns3/host-export.h | 4 +-
>> drivers/usb/cdnsp/Kconfig | 40 +
>> drivers/usb/cdnsp/Makefile | 7 +
>> drivers/usb/cdnsp/cdnsp-pci.c | 247 +++
>> drivers/usb/cdnsp/ep0.c | 480 ++++++
>> drivers/usb/cdnsp/gadget.c | 1946 ++++++++++++++++++++++++
>> drivers/usb/cdnsp/gadget.h | 139 ++
>> drivers/usb/cdnsp/mem.c | 1312 ++++++++++++++++
>> drivers/usb/cdnsp/ring.c | 2363 +++++++++++++++++++++++++++++
>> 15 files changed, 6600 insertions(+), 7 deletions(-)
>> create mode 100644 drivers/usb/cdnsp/Kconfig
>> create mode 100644 drivers/usb/cdnsp/Makefile
>> create mode 100644 drivers/usb/cdnsp/cdnsp-pci.c
>> create mode 100644 drivers/usb/cdnsp/ep0.c
>> create mode 100644 drivers/usb/cdnsp/gadget.c
>> create mode 100644 drivers/usb/cdnsp/mem.c
>> create mode 100644 drivers/usb/cdnsp/ring.c
>>
>> diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
>> index 26475b409b53..555c4a4cb465 100644
>> --- a/drivers/usb/Kconfig
>> +++ b/drivers/usb/Kconfig
>> @@ -112,6 +112,7 @@ source "drivers/usb/usbip/Kconfig"
>> endif
>>
>> source "drivers/usb/cdns3/Kconfig"
>> +source "drivers/usb/cdnsp/Kconfig"
>>
>> source "drivers/usb/mtu3/Kconfig"
>>
>> diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile
>> index 1c1c1d659394..84727f7a4b92 100644
>> --- a/drivers/usb/Makefile
>> +++ b/drivers/usb/Makefile
>> @@ -14,6 +14,7 @@ obj-$(CONFIG_USB_DWC2) += dwc2/
>> obj-$(CONFIG_USB_ISP1760) += isp1760/
>>
>> obj-$(CONFIG_USB_CDNS3) += cdns3/
>> +obj-$(CONFIG_USB_CDNSP) += cdnsp/
>>
>> obj-$(CONFIG_USB_MON) += mon/
>> obj-$(CONFIG_USB_MTU3) += mtu3/
>> diff --git a/drivers/usb/cdns3/core.c b/drivers/usb/cdns3/core.c
>> index 2af99294beaa..560783092d8a 100644
>> --- a/drivers/usb/cdns3/core.c
>> +++ b/drivers/usb/cdns3/core.c
>> @@ -138,7 +138,14 @@ static int cdns_core_init_role(struct cdns *cdns)
>> dr_mode = best_dr_mode;
>>
>> if (dr_mode == USB_DR_MODE_OTG || dr_mode == USB_DR_MODE_HOST) {
>> - ret = cdns_host_init(cdns);
>> + if ((cdns->version == CDNSP_CONTROLLER_V2 &&
>> + IS_ENABLED(CONFIG_USB_CDNSP_HOST)) ||
>> + (cdns->version < CDNSP_CONTROLLER_V2 &&
>> + IS_ENABLED(CONFIG_USB_CDNS3_HOST)))
>> + ret = cdns_host_init(cdns);
>> + else
>> + ret = -ENXIO;
>> +
>> if (ret) {
>> dev_err(dev, "Host initialization failed with %d\n",
>> ret);
>> @@ -147,7 +154,15 @@ static int cdns_core_init_role(struct cdns *cdns)
>> }
>>
>> if (dr_mode == USB_DR_MODE_OTG || dr_mode == USB_DR_MODE_PERIPHERAL) {
>> - ret = cdns3_gadget_init(cdns);
>> + if (cdns->version == CDNSP_CONTROLLER_V2 &&
>> + IS_ENABLED(CONFIG_USB_CDNSP_GADGET))
>> + ret = cdnsp_gadget_init(cdns);
>> + else if (cdns->version < CDNSP_CONTROLLER_V2 &&
>> + IS_ENABLED(CONFIG_USB_CDNS3_GADGET))
>> + ret = cdns3_gadget_init(cdns);
>> + else
>> + ret = -ENXIO;
>> +
>> if (ret) {
>> dev_err(dev, "Device initialization failed with %d\n",
>> ret);
>> diff --git a/drivers/usb/cdns3/drd.c b/drivers/usb/cdns3/drd.c
>> index 7feb622972da..3c732e19c61c 100644
>> --- a/drivers/usb/cdns3/drd.c
>> +++ b/drivers/usb/cdns3/drd.c
>> @@ -90,6 +90,32 @@ int cdns_get_vbus(struct cdns *cdns)
>> return vbus;
>> }
>>
>> +void cdns_clear_vbus(struct cdns *cdns)
>> +{
>> + u32 reg;
>> +
>> + if (cdns->version != CDNSP_CONTROLLER_V2)
>> + return;
>> +
>> + reg = readl(&cdns->otg_cdnsp_regs->override);
>> + reg |= OVERRIDE_SESS_VLD_SEL;
>> + writel(reg, &cdns->otg_cdnsp_regs->override);
>> +}
>> +EXPORT_SYMBOL_GPL(cdns_clear_vbus);
>> +
>> +void cdns_set_vbus(struct cdns *cdns)
>> +{
>> + u32 reg;
>> +
>> + if (cdns->version != CDNSP_CONTROLLER_V2)
>> + return;
>> +
>> + reg = readl(&cdns->otg_cdnsp_regs->override);
>> + reg &= ~OVERRIDE_SESS_VLD_SEL;
>> + writel(reg, &cdns->otg_cdnsp_regs->override);
>Is this use to force vbus-valid signal always valid? if it is,
>is there any issue if work as device only mode?

It only returns the control of vbus signal back to hardware.
cdns_clear/set_vbus are used only in cdnsp_gadget_pullup function for "software"
connect/disconnect. It cause that "software" connect/disconnect is
more like physical connect/disconnect.

I haven't seen any issue with this.

>
>> +}
>> +EXPORT_SYMBOL_GPL(cdns_set_vbus);
>> +
>> bool cdns_is_host(struct cdns *cdns)
>> {
>> if (cdns->dr_mode == USB_DR_MODE_HOST)
>> @@ -431,5 +457,7 @@ int cdns_drd_init(struct cdns *cdns)
>> int cdns_drd_exit(struct cdns *cdns)
>> {
>> cdns_otg_disable_irq(cdns);
>> + devm_free_irq(cdns->dev, cdns->otg_irq, cdns);
>> +
>> return 0;
>> }
>> diff --git a/drivers/usb/cdns3/drd.h b/drivers/usb/cdns3/drd.h
>> index b92e2834dc3f..7ef14bef047c 100644
>> --- a/drivers/usb/cdns3/drd.h
>> +++ b/drivers/usb/cdns3/drd.h
>> @@ -204,6 +204,8 @@ bool cdns_is_host(struct cdns *cdns);
>> bool cdns_is_device(struct cdns *cdns);
>> int cdns_get_id(struct cdns *cdns);
>> int cdns_get_vbus(struct cdns *cdns);
>> +extern void cdns_clear_vbus(struct cdns *cdns);
>> +extern void cdns_set_vbus(struct cdns *cdns);
>> int cdns_drd_init(struct cdns *cdns);
>> int cdns_drd_exit(struct cdns *cdns);
>> int cdns_drd_update_mode(struct cdns *cdns);
>> diff --git a/drivers/usb/cdns3/gadget-export.h b/drivers/usb/cdns3/gadget-export.h
>> index e784584fe053..b7eec9fb8fda 100644
>> --- a/drivers/usb/cdns3/gadget-export.h
>> +++ b/drivers/usb/cdns3/gadget-export.h
>> @@ -1,6 +1,6 @@
>> /* SPDX-License-Identifier: GPL-2.0 */
>> /*
>> - * Cadence USBSS DRD Driver - Gadget Export APIs.
>> + * Cadence USBSS and USBSSP DRD Driver - Gadget Export APIs.
>> *
>> * Copyright (C) 2017 NXP
>> * Copyright (C) 2017-2018 NXP
>> @@ -10,7 +10,19 @@
>> #ifndef __LINUX_CDNS3_GADGET_EXPORT
>> #define __LINUX_CDNS3_GADGET_EXPORT
>>
>> -#ifdef CONFIG_USB_CDNS3_GADGET
>> +#if IS_ENABLED(CONFIG_USB_CDNSP_GADGET)
>> +
>> +extern int cdnsp_gadget_init(struct cdns *cdns);
>> +#else
>> +
>> +static inline int cdnsp_gadget_init(struct cdns *cdns)
>> +{
>> + return -ENXIO;
>> +}
>> +
>> +#endif /* CONFIG_USB_CDNSP_GADGET */
>> +
>> +#if IS_ENABLED(CONFIG_USB_CDNS3_GADGET)
>>
>> extern int cdns3_gadget_init(struct cdns *cdns);
>> void cdns3_gadget_exit(struct cdns *cdns);
>> @@ -23,6 +35,6 @@ static inline int cdns3_gadget_init(struct cdns *cdns)
>>
>> static inline void cdns3_gadget_exit(struct cdns *cdns) { }
>>
>> -#endif
>> +#endif /* CONFIG_USB_CDNS3_GADGET */
>>
>> #endif /* __LINUX_CDNS3_GADGET_EXPORT */
>> diff --git a/drivers/usb/cdns3/host-export.h b/drivers/usb/cdns3/host-export.h
>> index d82b83d070ad..41f7ea1fed29 100644
>> --- a/drivers/usb/cdns3/host-export.h
>> +++ b/drivers/usb/cdns3/host-export.h
>> @@ -9,7 +9,7 @@
>> #ifndef __LINUX_CDNS3_HOST_EXPORT
>> #define __LINUX_CDNS3_HOST_EXPORT
>>
>> -#ifdef CONFIG_USB_CDNS3_HOST
>> +#if IS_ENABLED(CONFIG_USB_CDNS3_HOST) || IS_ENABLED(CONFIG_USB_CDNSP_GADGET)
>>
>> int cdns_host_init(struct cdns *cdns);
>>
>> @@ -22,6 +22,6 @@ static inline int cdns_host_init(struct cdns *cdns)
>>
>> static inline void cdns_host_exit(struct cdns *cdns) { }
>>
>> -#endif /* CONFIG_USB_CDNS3_HOST */
>> +#endif /* CONFIG_USB_CDNS3_HOST || CONFIG_USB_CDNSP_GADGET */
>>
>> #endif /* __LINUX_CDNS3_HOST_EXPORT */
>> diff --git a/drivers/usb/cdnsp/Kconfig b/drivers/usb/cdnsp/Kconfig
>> new file mode 100644
>> index 000000000000..56cee5f6dfb4
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/Kconfig
>> @@ -0,0 +1,40 @@
>> +config USB_CDNSP_PCI
>> + tristate "Cadence CDNSP Dual-Role Controller"
>> + depends on USB_SUPPORT && (USB || USB_GADGET) && HAS_DMA && USB_PCI && ACPI
>> + select USB_XHCI_PLATFORM if USB_XHCI_HCD
>> + select USB_ROLE_SWITCH
>> + select CDNS_USB_COMMON
>> + help
>> + Say Y here if your system has a Cadence CDNSP dual-role controller.
>> + It supports: dual-role switch Host-only, and Peripheral-only.
>> +
>> + If you choose to build this driver is a dynamically linked
>> + module, the module will be called cdnsp.ko.
>> +
>> +if USB_CDNSP_PCI
>> +
>> +config USB_CDNSP_GADGET
>> + bool "Cadence CDNSP device controller"
>> + depends on USB_GADGET=y || USB_GADGET=USB_CDNSP_PCI
>> + help
>> + Say Y here to enable device controller functionality of the
>> + Cadence CDNSP-DEV driver.
>> +
>> + Cadence CDNSP Device Controller in device mode is
>> + very similar to XHCI controller. Therefore some algorithms
>> + used has been taken from host driver.
>> + This controller supports FF, HS, SS and SSP mode.
>> + It doesn't support LS.
>> +
>> +config USB_CDNSP_HOST
>> + bool "Cadence CDNSP host controller"
>> + depends on USB=y || USB=USB_CDNSP_PCI
>> + select CDNS_USB_HOST
>> + help
>> + Say Y here to enable host controller functionality of the
>> + Cadence driver.
>> +
>> + Host controller is compliant with XHCI so it uses
>> + standard XHCI driver.
>> +
>> +endif
>> diff --git a/drivers/usb/cdnsp/Makefile b/drivers/usb/cdnsp/Makefile
>> new file mode 100644
>> index 000000000000..53202b21a8d2
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/Makefile
>> @@ -0,0 +1,7 @@
>> +# SPDX-License-Identifier: GPL-2.0
>> +
>> +cdnsp-udc-pci-y := cdnsp-pci.o
>> +
>> +obj-$(CONFIG_USB_CDNSP_PCI) += cdnsp-udc-pci.o
>> +cdnsp-udc-pci-$(CONFIG_USB_CDNSP_GADGET) += ring.o gadget.o mem.o ep0.o
>> +
>> diff --git a/drivers/usb/cdnsp/cdnsp-pci.c b/drivers/usb/cdnsp/cdnsp-pci.c
>> new file mode 100644
>> index 000000000000..f67ee8effcd3
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/cdnsp-pci.c
>> @@ -0,0 +1,247 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Cadence PCI Glue driver.
>> + *
>> + * Copyright (C) 2019 Cadence.
>> + *
>> + * Author: Pawel Laszczak <[email protected]>
>> + *
>> + */
>> +
>> +#include <linux/platform_device.h>
>> +#include <linux/dma-mapping.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/slab.h>
>> +#include <linux/pci.h>
>> +
>> +#include "../cdns3/core.h"
>> +
>> +#define PCI_BAR_HOST 0
>> +#define PCI_BAR_OTG 0
>> +#define PCI_BAR_DEV 2
>> +
>> +#define PCI_DEV_FN_HOST_DEVICE 0
>> +#define PCI_DEV_FN_OTG 1
>> +
>> +#define PCI_DRIVER_NAME "cdns-pci-usbssp"
>> +#define PLAT_DRIVER_NAME "cdns-usbssp"
>> +
>> +#define CDNS_VENDOR_ID 0x17cd
>> +#define CDNS_DEVICE_ID 0x0100
>> +#define CDNS_DRD_IF (PCI_CLASS_SERIAL_USB << 8 | 0x80)
>> +
>> +static struct pci_dev *cdnsp_get_second_fun(struct pci_dev *pdev)
>> +{
>> + struct pci_dev *func;
>> +
>> + /*
>> + * Gets the second function.
>> + * It's little tricky, but this platform has two function.
>> + * The fist keeps resources for Host/Device while the second
>> + * keeps resources for DRD/OTG.
>> + */
>> + func = pci_get_device(pdev->vendor, pdev->device, NULL);
>> + if (!func)
>> + return NULL;
>> +
>> + if (func->devfn == pdev->devfn) {
>> + func = pci_get_device(pdev->vendor, pdev->device, func);
>> + if (!func)
>> + return NULL;
>> + }
>> +
>> + return func;
>> +}
>> +
>> +static int cdnsp_pci_probe(struct pci_dev *pdev,
>> + const struct pci_device_id *id)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct pci_dev *func;
>> + struct resource *res;
>> + struct cdns *cdnsp;
>> + int ret;
>> +
>> + /*
>> + * For GADGET/HOST PCI (devfn) function number is 0,
>> + * for OTG PCI (devfn) function number is 1.
>> + */
>> + if (!id || (pdev->devfn != PCI_DEV_FN_HOST_DEVICE &&
>> + pdev->devfn != PCI_DEV_FN_OTG))
>> + return -EINVAL;
>> +
>> + func = cdnsp_get_second_fun(pdev);
>> + if (!func)
>> + return -EINVAL;
>> +
>> + if (func->class == PCI_CLASS_SERIAL_USB_XHCI ||
>> + pdev->class == PCI_CLASS_SERIAL_USB_XHCI) {
>> + ret = -EINVAL;
>> + goto put_pci;
>> + }
>> +
>> + ret = pcim_enable_device(pdev);
>> + if (ret) {
>> + dev_err(&pdev->dev, "Enabling PCI device has failed %d\n", ret);
>> + goto put_pci;
>> + }
>> +
>> + pci_set_master(pdev);
>> + if (pci_is_enabled(func)) {
>> + cdnsp = pci_get_drvdata(func);
>> + } else {
>> + cdnsp = kzalloc(sizeof(*cdnsp), GFP_KERNEL);
>> + if (!cdnsp) {
>> + ret = -ENOMEM;
>> + goto disable_pci;
>> + }
>> + }
>> +
>> + /* For GADGET device function number is 0. */
>> + if (pdev->devfn == 0) {
>> + resource_size_t rsrc_start, rsrc_len;
>> +
>> + /* Function 0: host(BAR_0) + device(BAR_1).*/
>> + dev_dbg(dev, "Initialize resources\n");
>> + rsrc_start = pci_resource_start(pdev, PCI_BAR_DEV);
>> + rsrc_len = pci_resource_len(pdev, PCI_BAR_DEV);
>> + res = devm_request_mem_region(dev, rsrc_start, rsrc_len, "dev");
>> + if (!res) {
>> + dev_dbg(dev, "controller already in use\n");
>> + ret = -EBUSY;
>> + goto free_cdnsp;
>> + }
>> +
>> + cdnsp->dev_regs = devm_ioremap(dev, rsrc_start, rsrc_len);
>> + if (!cdnsp->dev_regs) {
>> + dev_dbg(dev, "error mapping memory\n");
>> + ret = -EFAULT;
>> + goto free_cdnsp;
>> + }
>> +
>> + cdnsp->dev_irq = pdev->irq;
>> + dev_dbg(dev, "USBSS-DEV physical base addr: %pa\n",
>> + &rsrc_start);
>> +
>> + res = &cdnsp->xhci_res[0];
>> + res->start = pci_resource_start(pdev, PCI_BAR_HOST);
>> + res->end = pci_resource_end(pdev, PCI_BAR_HOST);
>> + res->name = "xhci";
>> + res->flags = IORESOURCE_MEM;
>> + dev_dbg(dev, "USBSS-XHCI physical base addr: %pa\n",
>> + &res->start);
>> +
>> + /* Interrupt for XHCI, */
>> + res = &cdnsp->xhci_res[1];
>> + res->start = pdev->irq;
>> + res->name = "host";
>> + res->flags = IORESOURCE_IRQ;
>> + } else {
>> + res = &cdnsp->otg_res;
>> + res->start = pci_resource_start(pdev, PCI_BAR_OTG);
>> + res->end = pci_resource_end(pdev, PCI_BAR_OTG);
>> + res->name = "otg";
>> + res->flags = IORESOURCE_MEM;
>> + dev_dbg(dev, "CDNSP-DRD physical base addr: %pa\n",
>> + &res->start);
>> +
>> + /* Interrupt for OTG/DRD. */
>> + cdnsp->otg_irq = pdev->irq;
>> + }
>> +
>> + if (pci_is_enabled(func)) {
>> + cdnsp->dev = dev;
>> +
>> + ret = cdns_init(cdnsp);
>> + if (ret)
>> + goto free_cdnsp;
>> + }
>> +
>> + pci_set_drvdata(pdev, cdnsp);
>> +
>> + device_wakeup_enable(&pdev->dev);
>> + if (pci_dev_run_wake(pdev))
>> + pm_runtime_put_noidle(&pdev->dev);
>> +
>> + return 0;
>> +
>> +free_cdnsp:
>> + if (!pci_is_enabled(func))
>> + kfree(cdnsp);
>> +
>> +disable_pci:
>> + pci_disable_device(pdev);
>> +
>> +put_pci:
>> + pci_dev_put(func);
>> +
>> + return ret;
>> +}
>> +
>> +static void cdnsp_pci_remove(struct pci_dev *pdev)
>> +{
>> + struct cdns *cdnsp;
>> + struct pci_dev *func;
>> +
>> + func = cdnsp_get_second_fun(pdev);
>> + cdnsp = (struct cdns *)pci_get_drvdata(pdev);
>> +
>> + if (pci_dev_run_wake(pdev))
>> + pm_runtime_get_noresume(&pdev->dev);
>> +
>> + if (!pci_is_enabled(func)) {
>> + kfree(cdnsp);
>> + goto pci_put;
>> + }
>> +
>> + cdns_remove(cdnsp);
>> +
>> +pci_put:
>> + pci_dev_put(func);
>> +}
>> +
>> +static int __maybe_unused cdnsp_pci_suspend(struct device *dev)
>> +{
>> + struct cdns *cdns = dev_get_drvdata(dev);
>> +
>> + return cdns_suspend(cdns);
>> +}
>> +
>> +static int __maybe_unused cdnsp_pci_resume(struct device *dev)
>> +{
>> + struct cdns *cdns = dev_get_drvdata(dev);
>> +
>> + return cdns_resume(cdns);
>> +}
>> +
>> +static const struct dev_pm_ops cdnsp_pci_pm_ops = {
>> + SET_SYSTEM_SLEEP_PM_OPS(cdnsp_pci_suspend, cdnsp_pci_resume)
>> +};
>> +
>> +static const struct pci_device_id cdnsp_pci_ids[] = {
>> + { PCI_VENDOR_ID_CDNS, CDNS_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,
>> + PCI_CLASS_SERIAL_USB_DEVICE, PCI_ANY_ID },
>> + { PCI_VENDOR_ID_CDNS, CDNS_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,
>> + CDNS_DRD_IF, PCI_ANY_ID },
>> + { 0, }
>> +};
>> +
>> +static struct pci_driver cdnsp_pci_driver = {
>> + .name = "cdnsp-pci",
>> + .id_table = &cdnsp_pci_ids[0],
>> + .probe = cdnsp_pci_probe,
>> + .remove = cdnsp_pci_remove,
>> + .driver = {
>> + .pm = &cdnsp_pci_pm_ops,
>> + }
>> +};
>> +
>> +module_pci_driver(cdnsp_pci_driver);
>> +MODULE_DEVICE_TABLE(pci, cdnsp_pci_ids);
>> +
>> +MODULE_ALIAS("pci:cdnsp");
>> +MODULE_AUTHOR("Pawel Laszczak <[email protected]>");
>> +MODULE_LICENSE("GPL v2");
>> +MODULE_DESCRIPTION("Cadence CDNSP PCI driver");
>> +
>> diff --git a/drivers/usb/cdnsp/ep0.c b/drivers/usb/cdnsp/ep0.c
>> new file mode 100644
>> index 000000000000..7f6e1d28d3b8
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/ep0.c
>> @@ -0,0 +1,480 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Cadence CDNSP DRD Driver.
>> + *
>> + * Copyright (C) 2020 Cadence.
>> + *
>> + * Author: Pawel Laszczak <[email protected]>
>> + *
>> + */
>> +
>> +#include <linux/usb/composite.h>
>> +#include <linux/usb/gadget.h>
>> +#include <linux/list.h>
>> +
>> +#include "gadget.h"
>> +
>> +static void cdnsp_ep0_stall(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_request *preq;
>> + struct cdnsp_ep *pep;
>> +
>> + pep = &pdev->eps[0];
>> + preq = next_request(&pep->pending_list);
>> +
>> + if (pdev->three_stage_setup) {
>> + cdnsp_halt_endpoint(pdev, pep, true);
>> +
>> + if (preq)
>> + cdnsp_gadget_giveback(pep, preq, -ECONNRESET);
>> + } else {
>> + pep->ep_state |= EP0_HALTED_STATUS;
>> +
>> + if (preq)
>> + list_del(&preq->list);
>> +
>> + cdnsp_status_stage(pdev);
>> + }
>> +}
>> +
>> +static int cdnsp_ep0_delegate_req(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + int ret;
>> +
>> + spin_unlock(&pdev->lock);
>> + ret = pdev->gadget_driver->setup(&pdev->gadget, ctrl);
>> + spin_lock(&pdev->lock);
>> +
>> + return ret;
>> +}
>> +
>> +static int cdnsp_ep0_set_config(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + enum usb_device_state state = pdev->gadget.state;
>> + u32 cfg;
>> + int ret;
>> +
>> + cfg = le16_to_cpu(ctrl->wValue);
>> +
>> + switch (state) {
>> + case USB_STATE_ADDRESS:
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> + if (ret)
>> + return ret;
>> + break;
>> + case USB_STATE_CONFIGURED:
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> + if (ret)
>> + return ret;
>What about moving cdnsp_ep0_delegate_req() after switch (), it's the
>same for ADDRESS & CONFIGURED state

I will remove duplicated code by using fallthrough in first case.
I will leave it in switch (). I think that it will be more readable.

>> + break;
>> + default:
>> + dev_err(pdev->dev, "Set Configuration - bad device state\n");
>> + return -EINVAL;
>> + }
>> +
>> + if (!cfg)
>> + usb_gadget_set_state(&pdev->gadget, USB_STATE_ADDRESS);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_ep0_set_address(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + enum usb_device_state state = pdev->gadget.state;
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + unsigned int slot_state;
>> + int ret;
>> + u32 addr;
>> +
>> + addr = le16_to_cpu(ctrl->wValue);
>> +
>> + if (addr > 127) {
>> + dev_err(pdev->dev, "Invalid device address %d\n", addr);
>> + return -EINVAL;
>> + }
>> +
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx);
>> +
>> + if (state == USB_STATE_CONFIGURED) {
>> + dev_err(pdev->dev, "Can't Set Address from Configured State\n");
>> + return -EINVAL;
>> + }
>> +
>> + pdev->device_address = le16_to_cpu(ctrl->wValue);
>> +
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx);
>> + slot_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state));
>> + if (slot_state == SLOT_STATE_ADDRESSED)
>> + cdnsp_reset_device(pdev);
>> +
>> + /*set device address*/
>> + ret = cdnsp_setup_device(pdev, SETUP_CONTEXT_ADDRESS);
>> + if (ret)
>> + return ret;
>> +
>> + if (addr)
>> + usb_gadget_set_state(&pdev->gadget, USB_STATE_ADDRESS);
>> + else
>> + usb_gadget_set_state(&pdev->gadget, USB_STATE_DEFAULT);
>> +
>> + return 0;
>> +}
>> +
>> +int cdnsp_status_stage(struct cdnsp_device *pdev)
>> +{
>> + pdev->ep0_stage = CDNSP_STATUS_STAGE;
>> + pdev->ep0_preq.request.length = 0;
>> +
>> + return cdnsp_ep_enqueue(pdev->ep0_preq.pep, &pdev->ep0_preq);
>> +}
>> +
>> +static int cdnsp_w_index_to_ep_index(__le32 wIndex)
>> +{
>> + wIndex = le32_to_cpu(wIndex);
>> +
>> + if (!(wIndex & USB_ENDPOINT_NUMBER_MASK))
>> + return 0;
>> +
>> + return ((wIndex & USB_ENDPOINT_NUMBER_MASK) * 2) +
>> + (wIndex & USB_ENDPOINT_DIR_MASK ? 1 : 0) - 1;
>> +}
>> +
>> +static int cdnsp_ep0_handle_status(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + struct cdnsp_ep *pep;
>> + __le16 *response;
>> + int ep_sts = 0;
>> + u16 status = 0;
>> + u32 recipient;
>> +
>> + recipient = ctrl->bRequestType & USB_RECIP_MASK;
>> +
>> + switch (recipient) {
>> + case USB_RECIP_DEVICE:
>> + status = pdev->gadget.is_selfpowered;
>> + status |= pdev->may_wakeup << USB_DEVICE_REMOTE_WAKEUP;
>> +
>> + if (pdev->gadget.speed >= USB_SPEED_SUPER) {
>> + status |= pdev->u1_allowed << USB_DEV_STAT_U1_ENABLED;
>> + status |= pdev->u2_allowed << USB_DEV_STAT_U2_ENABLED;
>> + }
>> + break;
>> + case USB_RECIP_INTERFACE:
>> + /*
>> + * Function Remote Wake Capable D0
>> + * Function Remote Wakeup D1
>> + */
>> + return cdnsp_ep0_delegate_req(pdev, ctrl);
>> + case USB_RECIP_ENDPOINT:
>> + pep = &pdev->eps[cdnsp_w_index_to_ep_index(ctrl->wIndex)];
>> + ep_sts = GET_EP_CTX_STATE(pep->out_ctx);
>> +
>> + /* check if endpoint is stalled */
>> + if (ep_sts == EP_STATE_HALTED)
>> + status = BIT(USB_ENDPOINT_HALT);
>> + break;
>> + default:
>> + return -EINVAL;
>> + }
>> +
>> + response = (__le16 *)pdev->setup_buf;
>> + *response = cpu_to_le16(status);
>> +
>> + pdev->ep0_preq.request.length = sizeof(*response);
>> + pdev->ep0_preq.request.buf = pdev->setup_buf;
>> +
>> + return cdnsp_ep_enqueue(pdev->ep0_preq.pep, &pdev->ep0_preq);
>> +}
>> +
>> +static void cdnsp_enter_test_mode(struct cdnsp_device *pdev)
>> +{
>> + u32 temp;
>> +
>> + temp = readl(&pdev->active_port->regs->portpmsc) & ~GENMASK(31, 28);
>> + temp |= PORT_TEST_MODE(pdev->test_mode);
>> + writel(temp, &pdev->active_port->regs->portpmsc);
>> + pdev->test_mode = 0;
>> +}
>> +
>> +static int cdnsp_ep0_handle_feature_device(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl,
>> + int set)
>> +{
>> + enum usb_device_state state;
>> + enum usb_device_speed speed;
>> + u16 tmode;
>> +
>> + state = pdev->gadget.state;
>> + speed = pdev->gadget.speed;
>> +
>> + switch (le16_to_cpu(ctrl->wValue)) {
>> + case USB_DEVICE_REMOTE_WAKEUP:
>> + pdev->may_wakeup = !!set;
>> + break;
>> + case USB_DEVICE_U1_ENABLE:
>> + if (state != USB_STATE_CONFIGURED || speed < USB_SPEED_SUPER)
>> + return -EINVAL;
>> +
>> + pdev->u1_allowed = !!set;
>> + break;
>> + case USB_DEVICE_U2_ENABLE:
>> + if (state != USB_STATE_CONFIGURED || speed < USB_SPEED_SUPER)
>> + return -EINVAL;
>> +
>> + pdev->u2_allowed = !!set;
>> + break;
>> + case USB_DEVICE_LTM_ENABLE:
>> + return -EINVAL;
>> + case USB_DEVICE_TEST_MODE:
>> + if (state != USB_STATE_CONFIGURED || speed > USB_SPEED_HIGH)
>> + return -EINVAL;
>> +
>> + tmode = le16_to_cpu(ctrl->wIndex);
>> +
>> + if (!set || (tmode & 0xff) != 0)
>> + return -EINVAL;
>> +
>> + tmode = tmode >> 8;
>> +
>> + if (tmode > USB_TEST_FORCE_ENABLE || tmode < USB_TEST_J)
>> + return -EINVAL;
>> +
>> + pdev->test_mode = tmode;
>> +
>> + /*
>> + * Test mode must be set before Status Stage but controller
>> + * will start testing sequence after Status Stage.
>> + */
>> + cdnsp_enter_test_mode(pdev);
>> + break;
>> + default:
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_ep0_handle_feature_intf(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl,
>> + int set)
>> +{
>> + u16 wValue, wIndex;
>> + int ret;
>> +
>> + wValue = le16_to_cpu(ctrl->wValue);
>> + wIndex = le16_to_cpu(ctrl->wIndex);
>> +
>> + switch (wValue) {
>> + case USB_INTRF_FUNC_SUSPEND:
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> + if (ret)
>> + return ret;
>> +
>> + /*
>> + * Remote wakeup is enabled when any function within a device
>> + * is enabled for function remote wakeup.
>> + */
>> + if (wIndex & USB_INTRF_FUNC_SUSPEND_RW)
>> + pdev->may_wakeup++;
>> + else
>> + if (pdev->may_wakeup > 0)
>> + pdev->may_wakeup--;
>> +
>> + return 0;
>> + default:
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_ep0_handle_feature_endpoint(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl,
>> + int set)
>> +{
>> + struct cdnsp_ep *pep;
>> + u32 wValue;
>> +
>> + wValue = le16_to_cpu(ctrl->wValue);
>> + pep = &pdev->eps[cdnsp_w_index_to_ep_index(ctrl->wIndex)];
>> +
>> + switch (wValue) {
>> + case USB_ENDPOINT_HALT:
>> + if (!set && (pep->ep_state & EP_WEDGE)) {
>> + /* Resets Sequence Number */
>> + cdnsp_halt_endpoint(pdev, pep, 0);
>> + cdnsp_halt_endpoint(pdev, pep, 1);
>> + break;
>> + }
>> +
>> + return cdnsp_halt_endpoint(pdev, pep, set);
>> + default:
>> + dev_warn(pdev->dev, "WARN Incorrect wValue %04x\n", wValue);
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_ep0_handle_feature(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl,
>> + int set)
>> +{
>> + switch (ctrl->bRequestType & USB_RECIP_MASK) {
>> + case USB_RECIP_DEVICE:
>> + return cdnsp_ep0_handle_feature_device(pdev, ctrl, set);
>> + case USB_RECIP_INTERFACE:
>> + return cdnsp_ep0_handle_feature_intf(pdev, ctrl, set);
>> + case USB_RECIP_ENDPOINT:
>> + return cdnsp_ep0_handle_feature_endpoint(pdev, ctrl, set);
>> + default:
>> + return -EINVAL;
>> + }
>> +}
>> +
>> +static int cdnsp_ep0_set_sel(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + enum usb_device_state state = pdev->gadget.state;
>> + u16 wLength;
>> +
>> + if (state == USB_STATE_DEFAULT)
>> + return -EINVAL;
>> +
>> + wLength = le16_to_cpu(ctrl->wLength);
>> +
>> + if (wLength != 6) {
>> + dev_err(pdev->dev, "Set SEL should be 6 bytes, got %d\n",
>> + wLength);
>> + return -EINVAL;
>> + }
>> +
>> + /*
>> + * To handle Set SEL we need to receive 6 bytes from Host. So let's
>> + * queue a usb_request for 6 bytes.
>> + */
>> + pdev->ep0_preq.request.length = 6;
>> + pdev->ep0_preq.request.buf = pdev->setup_buf;
>> +
>> + return cdnsp_ep_enqueue(pdev->ep0_preq.pep, &pdev->ep0_preq);
>> +}
>> +
>> +static int cdnsp_ep0_set_isoch_delay(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + if (le16_to_cpu(ctrl->wIndex) || le16_to_cpu(ctrl->wLength))
>> + return -EINVAL;
>> +
>> + pdev->gadget.isoch_delay = le16_to_cpu(ctrl->wValue);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_ep0_std_request(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + int ret;
>> +
>> + switch (ctrl->bRequest) {
>> + case USB_REQ_GET_STATUS:
>> + ret = cdnsp_ep0_handle_status(pdev, ctrl);
>> + break;
>> + case USB_REQ_CLEAR_FEATURE:
>> + ret = cdnsp_ep0_handle_feature(pdev, ctrl, 0);
>> + break;
>> + case USB_REQ_SET_FEATURE:
>> + ret = cdnsp_ep0_handle_feature(pdev, ctrl, 1);
>> + break;
>> + case USB_REQ_SET_ADDRESS:
>> + ret = cdnsp_ep0_set_address(pdev, ctrl);
>> + break;
>> + case USB_REQ_SET_CONFIGURATION:
>> + ret = cdnsp_ep0_set_config(pdev, ctrl);
>> + break;
>> + case USB_REQ_SET_SEL:
>> + ret = cdnsp_ep0_set_sel(pdev, ctrl);
>> + break;
>> + case USB_REQ_SET_ISOCH_DELAY:
>> + ret = cdnsp_ep0_set_isoch_delay(pdev, ctrl);
>> + break;
>> + case USB_REQ_SET_INTERFACE:
>> + /*
>> + * Add request into pending list to block sending status stage
>> + * by libcomposite.
>> + */
>> + list_add_tail(&pdev->ep0_preq.list,
>> + &pdev->ep0_preq.pep->pending_list);
>> +
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> + if (ret == -EBUSY)
>> + ret = 0;
>> +
>> + list_del(&pdev->ep0_preq.list);
>> + break;
>> + default:
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> + break;
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +void cdnsp_setup_analyze(struct cdnsp_device *pdev)
>> +{
>> + struct usb_ctrlrequest *ctrl = &pdev->setup;
>> + int ret = 0;
>> + __le16 len;
>> +
>> + if (!pdev->gadget_driver)
>> + goto out;
>> +
>> + if (pdev->gadget.state == USB_STATE_NOTATTACHED) {
>> + dev_err(pdev->dev, "ERR: Setup detected in unattached state\n");
>> + ret = -EINVAL;
>> + goto out;
>> + }
>> +
>> + /* Restore the ep0 to Stopped/Running state. */
>> + if (pdev->eps[0].ep_state & EP_HALTED)
>> + cdnsp_halt_endpoint(pdev, &pdev->eps[0], 0);
>> +
>> + /*
>> + * Finishing previous SETUP transfer by removing request from
>> + * list and informing upper layer
>> + */
>> + if (!list_empty(&pdev->eps[0].pending_list)) {
>> + struct cdnsp_request *req;
>> +
>> + req = next_request(&pdev->eps[0].pending_list);
>> + cdnsp_ep_dequeue(&pdev->eps[0], req);
>> + }
>> +
>> + len = le16_to_cpu(ctrl->wLength);
>> + if (!len) {
>> + pdev->three_stage_setup = false;
>> + pdev->ep0_expect_in = false;
>> + } else {
>> + pdev->three_stage_setup = true;
>> + pdev->ep0_expect_in = !!(ctrl->bRequestType & USB_DIR_IN);
>> + }
>> +
>> + if ((ctrl->bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD)
>> + ret = cdnsp_ep0_std_request(pdev, ctrl);
>> + else
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> +
>> + if (!len)
>> + pdev->ep0_stage = CDNSP_STATUS_STAGE;
>> +
>> + if (ret == USB_GADGET_DELAYED_STATUS)
>> + return;
>> +out:
>> + if (ret < 0)
>> + cdnsp_ep0_stall(pdev);
>> + else if (pdev->ep0_stage == CDNSP_STATUS_STAGE)
>> + cdnsp_status_stage(pdev);
>> +}
>> diff --git a/drivers/usb/cdnsp/gadget.c b/drivers/usb/cdnsp/gadget.c
>> new file mode 100644
>> index 000000000000..38ad170b2bdd
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/gadget.c
>> @@ -0,0 +1,1946 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Cadence CDNSP DRD Driver.
>> + *
>> + * Copyright (C) 2020 Cadence.
>> + *
>> + * Author: Pawel Laszczak <[email protected]>
>> + *
>> + */
>> +
>> +#include <linux/moduleparam.h>
>> +#include <linux/dma-mapping.h>
>> +#include <linux/module.h>
>> +#include <linux/iopoll.h>
>> +#include <linux/delay.h>
>> +#include <linux/log2.h>
>> +#include <linux/slab.h>
>> +#include <linux/pci.h>
>> +#include <linux/irq.h>
>> +#include <linux/dmi.h>
>> +
>> +#include "../cdns3/core.h"
>> +#include "../cdns3/gadget-export.h"
>> +#include "../cdns3/drd.h"
>> +#include "gadget.h"
>> +
>> +unsigned int cdnsp_port_speed(unsigned int port_status)
>> +{
>> + /*Detect gadget speed based on PORTSC register*/
>> + if (DEV_SUPERSPEEDPLUS(port_status))
>> + return USB_SPEED_SUPER_PLUS;
>> + else if (DEV_SUPERSPEED(port_status))
>> + return USB_SPEED_SUPER;
>> + else if (DEV_HIGHSPEED(port_status))
>> + return USB_SPEED_HIGH;
>> + else if (DEV_FULLSPEED(port_status))
>> + return USB_SPEED_FULL;
>> +
>> + /* If device is detached then speed will be USB_SPEED_UNKNOWN.*/
>> + return USB_SPEED_UNKNOWN;
>> +}
>> +
>> +/*
>Use /* or /**?
>See doc-guide/kernel-doc.rst

What is wrong here ? I'm used /*. It's only function comment.
/** is used for function documentation. I'm using intentionally
/* in many places before functions.

>> + * Given a port state, this function returns a value that would result in the
>> + * port being in the same state, if the value was written to the port status
>> + * control register.
>> + * Save Read Only (RO) bits and save read/write bits where
>> + * writing a 0 clears the bit and writing a 1 sets the bit (RWS).
>> + * For all other types (RW1S, RW1CS, RW, and RZ), writing a '0' has no effect.
>> + */
>> +u32 cdnsp_port_state_to_neutral(u32 state)
>> +{
>> + /* Save read-only status and port state. */
>> + return (state & CDNSP_PORT_RO) | (state & CDNSP_PORT_RWS);
>> +}
>> +
>> +/**
>> + * Find the offset of the extended capabilities with capability ID id.
>> + * @base: PCI MMIO registers base address.
>> + * @start: Address at which to start looking, (0 or HCC_PARAMS to start at
>> + * beginning of list)
>> + * @id: Extended capability ID to search for.
>> + *
>> + * Returns the offset of the next matching extended capability structure.
>> + * Some capabilities can occur several times,
>> + * e.g., the EXT_CAPS_PROTOCOL, and this provides a way to find them all.
>> + */
>> +int cdnsp_find_next_ext_cap(void __iomem *base, u32 start, int id)
>> +{
>> + u32 offset = start;
>> + u32 next;
>> + u32 val;
>> +
>> + if (!start || start == HCC_PARAMS_OFFSET) {
>> + val = readl(base + HCC_PARAMS_OFFSET);
>> + if (val == ~0)
>> + return 0;
>> +
>> + offset = HCC_EXT_CAPS(val) << 2;
>> + if (!offset)
>> + return 0;
>> + };
>> +
>> + do {
>> + val = readl(base + offset);
>> + if (val == ~0)
>> + return 0;
>> +
>> + if (EXT_CAPS_ID(val) == id && offset != start)
>> + return offset;
>> +
>> + next = EXT_CAPS_NEXT(val);
>> + offset += next << 2;
>> + } while (next);
>> +
>> + return 0;
>> +}
>> +
>> +void cdnsp_set_link_state(struct cdnsp_device *pdev,
>> + __le32 __iomem *port_regs,
>> + u32 link_state)
>> +{
>> + u32 temp;
>> +
>> + temp = readl(port_regs);
>> + temp = cdnsp_port_state_to_neutral(temp);
>> + temp |= PORT_WKCONN_E | PORT_WKDISC_E;
>> + writel(temp, port_regs);
>> +
>> + temp &= ~PORT_PLS_MASK;
>> + temp |= PORT_LINK_STROBE | link_state;
>> +
>> + writel(temp, port_regs);
>> +}
>> +
>> +static void cdnsp_disable_port(struct cdnsp_device *pdev,
>> + __le32 __iomem *port_regs)
>> +{
>> + u32 temp = cdnsp_port_state_to_neutral(readl(port_regs));
>> +
>> + writel(temp | PORT_PED, port_regs);
>> +}
>> +
>> +static void cdnsp_clear_port_change_bit(struct cdnsp_device *pdev,
>> + __le32 __iomem *port_regs)
>> +{
>> + u32 portsc = readl(port_regs);
>> +
>> + writel(cdnsp_port_state_to_neutral(portsc) |
>> + (portsc & PORT_CHANGE_BITS), port_regs);
>> +}
>> +
>> +static void cdnsp_set_chicken_bits_2(struct cdnsp_device *pdev, u32 bit)
>> +{
>> + __le32 __iomem *reg;
>> + void __iomem *base;
>> + u32 offset = 0;
>> +
>> + base = &pdev->cap_regs->hc_capbase;
>> + offset = cdnsp_find_next_ext_cap(base, offset, D_XEC_PRE_REGS_CAP);
>> + reg = base + offset + REG_CHICKEN_BITS_2_OFFSET;
>> +
>> + bit = readl(reg) | bit;
>> + writel(bit, reg);
>> +}
>> +
>> +static void cdnsp_clear_chicken_bits_2(struct cdnsp_device *pdev, u32 bit)
>> +{
>> + __le32 __iomem *reg;
>> + void __iomem *base;
>> + u32 offset = 0;
>> +
>> + base = &pdev->cap_regs->hc_capbase;
>> + offset = cdnsp_find_next_ext_cap(base, offset, D_XEC_PRE_REGS_CAP);
>> + reg = base + offset + REG_CHICKEN_BITS_2_OFFSET;
>> +
>> + bit = readl(reg) & ~bit;
>> + writel(bit, reg);
>> +}
>> +
>> +/*
>> + * Disable interrupts and begin the controller halting process.
>> + */
>> +static void cdnsp_quiesce(struct cdnsp_device *pdev)
>> +{
>> + u32 halted;
>> + u32 mask;
>> + u32 cmd;
>> +
>> + mask = ~(u32)(CDNSP_IRQS);
>> +
>> + halted = readl(&pdev->op_regs->status) & STS_HALT;
>> + if (!halted)
>> + mask &= ~(CMD_R_S | CMD_DEVEN);
>> +
>> + cmd = readl(&pdev->op_regs->command);
>> + cmd &= mask;
>> + writel(cmd, &pdev->op_regs->command);
>> +}
>> +
>> +/*
>> + * Force controller into halt state.
>> + *
>> + * Disable any IRQs and clear the run/stop bit.
>> + * Controller will complete any current and actively pipelined transactions, and
>> + * should halt within 16 ms of the run/stop bit being cleared.
>> + * Read controller Halted bit in the status register to see when the
>> + * controller is finished.
>> + */
>> +int cdnsp_halt(struct cdnsp_device *pdev)
>> +{
>> + int ret;
>> + u32 val;
>> +
>> + cdnsp_quiesce(pdev);
>> +
>> + ret = readl_poll_timeout_atomic(&pdev->op_regs->status, val,
>> + val & STS_HALT, 1,
>> + CDNSP_MAX_HALT_USEC);
>> + if (ret) {
>> + dev_err(pdev->dev, "ERROR: Device halt failed\n");
>> + return ret;
>> + }
>> +
>> + pdev->cdnsp_state |= CDNSP_STATE_HALTED;
>> +
>> + return 0;
>> +}
>> +
>> +/*
>> + * device controller died, register read returns 0xffffffff, or command never
>> + * ends.
>> + */
>> +void cdnsp_died(struct cdnsp_device *pdev)
>> +{
>> + dev_err(pdev->dev, "ERROR: CDNSP controller not responding\n");
>> + pdev->cdnsp_state |= CDNSP_STATE_DYING;
>> + cdnsp_halt(pdev);
>> +}
>> +
>> +/*
>> + * Set the run bit and wait for the device to be running.
>> + */
>> +static int cdnsp_start(struct cdnsp_device *pdev)
>> +{
>> + u32 temp;
>> + int ret;
>> +
>> + temp = readl(&pdev->op_regs->command);
>> + temp |= (CMD_R_S | CMD_DEVEN);
>> + writel(temp, &pdev->op_regs->command);
>> +
>> + pdev->cdnsp_state = 0;
>> +
>> + /*
>> + * Wait for the STS_HALT Status bit to be 0 to indicate the device is
>> + * running.
>> + */
>> + ret = readl_poll_timeout_atomic(&pdev->op_regs->status, temp,
>> + !(temp & STS_HALT), 1,
>> + CDNSP_MAX_HALT_USEC);
>> + if (ret) {
>> + pdev->cdnsp_state = CDNSP_STATE_DYING;
>> + dev_err(pdev->dev, "ERROR: Controller run failed\n");
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * Reset a halted controller.
>> + *
>> + * This resets pipelines, timers, counters, state machines, etc.
>> + * Transactions will be terminated immediately, and operational registers
>> + * will be set to their defaults.
>> + */
>> +int cdnsp_reset(struct cdnsp_device *pdev)
>> +{
>> + u32 command;
>> + u32 temp;
>> + int ret;
>> +
>> + temp = readl(&pdev->op_regs->status);
>> +
>> + if (temp == ~(u32)0) {
>> + dev_err(pdev->dev, "Device not accessible, reset failed.\n");
>> + return -ENODEV;
>> + }
>> +
>> + if ((temp & STS_HALT) == 0) {
>> + dev_err(pdev->dev, "Controller not halted, aborting reset.\n");
>> + return -EINVAL;
>> + }
>> +
>> + command = readl(&pdev->op_regs->command);
>> + command |= CMD_RESET;
>> + writel(command, &pdev->op_regs->command);
>> +
>> + ret = readl_poll_timeout_atomic(&pdev->op_regs->command, temp,
>> + !(temp & CMD_RESET), 1,
>> + 10 * 1000);
>> + if (ret) {
>> + dev_err(pdev->dev, "ERROR: Controller reset failed\n");
>> + return ret;
>> + }
>> +
>> + /*
>> + * CDNSP cannot write any doorbells or operational registers other
>> + * than status until the "Controller Not Ready" flag is cleared.
>> + */
>> + ret = readl_poll_timeout_atomic(&pdev->op_regs->status, temp,
>> + !(temp & STS_CNR), 1,
>> + 10 * 1000);
>> +
>> + if (ret) {
>> + dev_err(pdev->dev, "ERROR: Controller not ready to work\n");
>> + return ret;
>> + }
>> +
>> + dev_info(pdev->dev, "Controller ready to work");
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * cdnsp_get_endpoint_index - Find the index for an endpoint given its
>> + * descriptor.Use the return value to right shift 1 for the bitmask.
>> + *
>> + * Index = (epnum * 2) + direction - 1,
>> + * where direction = 0 for OUT, 1 for IN.
>> + * For control endpoints, the IN index is used (OUT index is unused), so
>> + * index = (epnum * 2) + direction - 1 = (epnum * 2) + 1 - 1 = (epnum * 2)
>> + */
>> +static unsigned int
>> + cdnsp_get_endpoint_index(const struct usb_endpoint_descriptor *desc)
>> +{
>> + unsigned int index = (unsigned int)usb_endpoint_num(desc);
>> +
>> + if (usb_endpoint_xfer_control(desc))
>> + return index * 2;
>> +
>> + return (index * 2) + (usb_endpoint_dir_in(desc) ? 1 : 0) - 1;
>> +}
>> +
>> +/*
>> + * Find the flag for this endpoint (for use in the control context). Use the
>> + * endpoint index to create a bitmask. The slot context is bit 0, endpoint 0 is
>> + * bit 1, etc.
>> + */
>> +static unsigned int
>> + cdnsp_get_endpoint_flag(const struct usb_endpoint_descriptor *desc)
>> +{
>> + return 1 << (cdnsp_get_endpoint_index(desc) + 1);
>> +}
>> +
>> +int cdnsp_ep_enqueue(struct cdnsp_ep *pep, struct cdnsp_request *preq)
>> +{
>> + struct cdnsp_device *pdev = pep->pdev;
>> + struct usb_request *request;
>> + int ret;
>> +
>> + if (preq->epnum == 0 && !list_empty(&pep->pending_list))
>> + return -EBUSY;
>> +
>> + request = &preq->request;
>> + request->actual = 0;
>> + request->status = -EINPROGRESS;
>> + preq->direction = pep->direction;
>> + preq->epnum = pep->number;
>> + preq->td.drbl = 0;
>> +
>> + ret = usb_gadget_map_request_by_dev(pdev->dev, request, pep->direction);
>> + if (ret)
>> + return ret;
>> +
>> + list_add_tail(&preq->list, &pep->pending_list);
>> +
>> + switch (usb_endpoint_type(pep->endpoint.desc)) {
>> + case USB_ENDPOINT_XFER_CONTROL:
>> + ret = cdnsp_queue_ctrl_tx(pdev, preq);
>> + break;
>> + case USB_ENDPOINT_XFER_BULK:
>> + case USB_ENDPOINT_XFER_INT:
>> + ret = cdnsp_queue_bulk_tx(pdev, preq);
>> + break;
>> + case USB_ENDPOINT_XFER_ISOC:
>> + ret = cdnsp_queue_isoc_tx_prepare(pdev, preq);
>> + }
>> +
>> + if (ret)
>> + goto unmap;
>> +
>> + return 0;
>> +
>> +unmap:
>> + usb_gadget_unmap_request_by_dev(pdev->dev, &preq->request,
>> + pep->direction);
>> + list_del(&preq->list);
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * Remove the request's TD from the endpoint ring. This may cause the
>> + * controller to stop USB transfers, potentially stopping in the middle of a
>> + * TRB buffer. The controller should pick up where it left off in the TD,
>> + * unless a Set Transfer Ring Dequeue Pointer is issued.
>> + *
>> + * The TRBs that make up the buffers for the canceled request will be "removed"
>> + * from the ring. Since the ring is a contiguous structure, they can't be
>> + * physically removed. Instead, there are two options:
>> + *
>> + * 1) If the controller is in the middle of processing the request to be
>> + * canceled, we simply move the ring's dequeue pointer past those TRBs
>> + * using the Set Transfer Ring Dequeue Pointer command. This will be
>> + * the common case, when drivers timeout on the last submitted request
>> + * and attempt to cancel.
>> + *
>> + * 2) If the controller is in the middle of a different TD, we turn the TRBs
>> + * into a series of 1-TRB transfer no-op TDs. No-ops shouldn't be chained.
>> + * The controller will need to invalidate the any TRBs it has cached after
>> + * the stop endpoint command.
>> + *
>> + * 3) The TD may have completed by the time the Stop Endpoint Command
>> + * completes, so software needs to handle that case too.
>> + *
>> + */
>> +int cdnsp_ep_dequeue(struct cdnsp_ep *pep, struct cdnsp_request *preq)
>> +{
>> + struct cdnsp_device *pdev = pep->pdev;
>> + int ret;
>> +
>> + if (GET_EP_CTX_STATE(pep->out_ctx) == EP_STATE_RUNNING) {
>> + ret = cdnsp_cmd_stop_ep(pdev, pep);
>> + if (ret)
>> + return ret;
>> + }
>> +
>> + return cdnsp_remove_request(pdev, preq, pep);
>> +}
>> +
>> +static void cdnsp_zero_in_ctx(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_input_control_ctx *ctrl_ctx;
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + struct cdnsp_ep_ctx *ep_ctx;
>> + int i;
>> +
>> + ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx);
>> +
>> + /*
>> + * When a device's add flag and drop flag are zero, any subsequent
>> + * configure endpoint command will leave that endpoint's state
>> + * untouched. Make sure we don't leave any old state in the input
>> + * endpoint contexts.
>> + */
>> + ctrl_ctx->drop_flags = 0;
>> + ctrl_ctx->add_flags = 0;
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx);
>> + slot_ctx->dev_info &= cpu_to_le32(~LAST_CTX_MASK);
>> +
>> + /* Endpoint 0 is always valid */
>> + slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(1));
>> + for (i = 1; i < 31; ++i) {
>> + ep_ctx = cdnsp_get_ep_ctx(&pdev->in_ctx, i);
>> + ep_ctx->ep_info = 0;
>> + ep_ctx->ep_info2 = 0;
>> + ep_ctx->deq = 0;
>> + ep_ctx->tx_info = 0;
>> + }
>> +}
>> +
>> +/* Issue a configure endpoint command and wait for it to finish. */
>> +static int cdnsp_configure_endpoint(struct cdnsp_device *pdev)
>> +{
>> + int ret;
>> +
>> + cdnsp_queue_configure_endpoint(pdev, pdev->cmd.in_ctx->dma);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> + if (ret) {
>> + dev_err(pdev->dev,
>> + "ERR: unexpected command completion code 0x%x.\n", ret);
>> + return -EINVAL;
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +static void cdnsp_invalidate_ep_events(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep)
>> +{
>> + struct cdnsp_segment *segment;
>> + union cdnsp_trb *event;
>> + u32 cycle_state;
>> + __le32 data;
>> +
>> + event = pdev->event_ring->dequeue;
>> + segment = pdev->event_ring->deq_seg;
>> + cycle_state = pdev->event_ring->cycle_state;
>> +
>> + while (1) {
>> + data = le32_to_cpu(event->trans_event.flags);
>> +
>> + /* Check the owner of the TRB. */
>> + if ((data & TRB_CYCLE) != cycle_state)
>> + break;
>> +
>> + if (TRB_FIELD_TO_TYPE(data) == TRB_TRANSFER &&
>> + TRB_TO_EP_ID(data) == (pep->idx + 1)) {
>> + data |= TRB_EVENT_INVALIDATE;
>> + event->trans_event.flags = cpu_to_le32(data);
>> + }
>> +
>> + if (cdnsp_last_trb_on_seg(segment, event)) {
>> + cycle_state ^= 1;
>> + segment = pdev->event_ring->deq_seg->next;
>> + event = segment->trbs;
>> + } else {
>> + event++;
>> + }
>> + }
>> +}
>> +
>> +int cdnsp_wait_for_cmd_compl(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_segment *event_deq_seg;
>> + dma_addr_t cmd_deq_dma;
>> + union cdnsp_trb *cmd_trb;
>> + union cdnsp_trb *event;
>> + u32 cycle_state;
>> + __le32 flags;
>> + int ret, val;
>> + u64 cmd_dma;
>> +
>> + cmd_trb = pdev->cmd.command_trb;
>> + pdev->cmd.status = 0;
>> +
>> + ret = readl_poll_timeout_atomic(&pdev->op_regs->cmd_ring, val,
>> + !CMD_RING_BUSY(val), 1,
>> + CDNSP_CMD_TIMEOUT);
>> + if (ret) {
>> + dev_err(pdev->dev, "ERR: Timeout while waiting for command\n");
>> + pdev->cdnsp_state = CDNSP_STATE_DYING;
>> + return -ETIMEDOUT;
>> + }
>> +
>> + event = pdev->event_ring->dequeue;
>> + event_deq_seg = pdev->event_ring->deq_seg;
>> + cycle_state = pdev->event_ring->cycle_state;
>> +
>> + cmd_deq_dma = cdnsp_trb_virt_to_dma(pdev->cmd_ring->deq_seg, cmd_trb);
>> + if (!cmd_deq_dma)
>> + return -EINVAL;
>> +
>> + while (1) {
>> + flags = le32_to_cpu(event->event_cmd.flags);
>> +
>> + /* Check the owner of the TRB. */
>> + if ((flags & TRB_CYCLE) != cycle_state)
>> + return -EINVAL;
>> +
>> + cmd_dma = le64_to_cpu(event->event_cmd.cmd_trb);
>> +
>> + /*
>> + * Check whether the completion event is for last queued
>> + * command.
>> + */
>> + if (TRB_FIELD_TO_TYPE(flags) != TRB_COMPLETION ||
>> + cmd_dma != (u64)cmd_deq_dma) {
>> + if (!cdnsp_last_trb_on_seg(event_deq_seg, event)) {
>> + event++;
>> + continue;
>> + }
>> +
>> + if (cdnsp_last_trb_on_ring(pdev->event_ring,
>> + event_deq_seg, event))
>> + cycle_state ^= 1;
>> +
>> + event_deq_seg = event_deq_seg->next;
>> + event = event_deq_seg->trbs;
>> + continue;
>> + }
>> +
>> + pdev->cmd.status = GET_COMP_CODE(le32_to_cpu(event->event_cmd.status));
>> + if (pdev->cmd.status == COMP_SUCCESS)
>> + return 0;
>
>> +
>> + return -pdev->cmd.status;
>> + }
>> +
>> + return 0;
>Maybe no need if no break in while()

Yes, it's not needed.

>> +}
>> +
>> +int cdnsp_halt_endpoint(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep,
>> + int value)
>> +{
>> + int ret;
>> +
>> + if (value) {
>> + ret = cdnsp_cmd_stop_ep(pdev, pep);
>> + if (ret)
>> + return ret;
>> +
>> + if (GET_EP_CTX_STATE(pep->out_ctx) == EP_STATE_STOPPED) {
>> + cdnsp_queue_halt_endpoint(pdev, pep->idx);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> + }
>> +
>> + pep->ep_state |= EP_HALTED;
>> + } else {
>> + /*
>> + * In device mode driver can call reset endpoint command
>> + * from any endpoint state.
>> + */
>> + cdnsp_queue_reset_ep(pdev, pep->idx);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> + if (ret)
>> + return ret;
>> +
>> + pep->ep_state &= ~EP_HALTED;
>> +
>> + if (pep->idx != 0 && !(pep->ep_state & EP_WEDGE))
>> + cdnsp_ring_doorbell_for_active_rings(pdev, pep);
>> +
>> + pep->ep_state &= ~EP_WEDGE;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_update_eps_configuration(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep)
>> +{
>> + struct cdnsp_input_control_ctx *ctrl_ctx;
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + int ret = 0;
>> + u32 ep_sts;
>> + int i;
>> +
>> + ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx);
>> +
>> + /* Don't issue the command if there's no endpoints to update. */
>> + if (ctrl_ctx->add_flags == 0 && ctrl_ctx->drop_flags == 0)
>> + return 0;
>> +
>> + ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG);
>> + ctrl_ctx->add_flags &= cpu_to_le32(~EP0_FLAG);
>> + ctrl_ctx->drop_flags &= cpu_to_le32(~(SLOT_FLAG | EP0_FLAG));
>> +
>> + /* Fix up Context Entries field. Minimum value is EP0 == BIT(1). */
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx);
>> + for (i = 31; i >= 1; i--) {
>> + __le32 le32 = cpu_to_le32(BIT(i));
>> +
>> + if ((pdev->eps[i - 1].ring && !(ctrl_ctx->drop_flags & le32)) ||
>> + (ctrl_ctx->add_flags & le32) || i == 1) {
>> + slot_ctx->dev_info &= cpu_to_le32(~LAST_CTX_MASK);
>> + slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(i));
>> + break;
>> + }
>> + }
>> +
>> + ep_sts = GET_EP_CTX_STATE(pep->out_ctx);
>> +
>> + if ((ctrl_ctx->add_flags != cpu_to_le32(SLOT_FLAG) &&
>> + ep_sts == EP_STATE_DISABLED) ||
>> + (ep_sts != EP_STATE_DISABLED && ctrl_ctx->drop_flags))
>> + ret = cdnsp_configure_endpoint(pdev);
>> +
>> + cdnsp_zero_in_ctx(pdev);
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * This submits a Reset Device Command, which will set the device state to 0,
>> + * set the device address to 0, and disable all the endpoints except the default
>> + * control endpoint. The USB core should come back and call
>> + * cdnsp_setup_device(), and then re-set up the configuration.
>> + */
>> +int cdnsp_reset_device(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + int slot_state;
>> + int ret, i;
>> +
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx);
>> + slot_ctx->dev_info = 0;
>> + pdev->device_address = 0;
>> +
>> + /* If device is not setup, there is no point in resetting it. */
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx);
>> + slot_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state));
>> +
>> + if (slot_state <= SLOT_STATE_DEFAULT &&
>> + pdev->eps[0].ep_state & EP_HALTED) {
>> + cdnsp_halt_endpoint(pdev, &pdev->eps[0], 0);
>> + }
>> +
>> + /*
>> + * During Reset Device command controller shall transition the
>> + * endpoint ep0 to the Running State.
>> + */
>> + pdev->eps[0].ep_state &= ~(EP_STOPPED | EP_HALTED);
>> + pdev->eps[0].ep_state |= EP_ENABLED;
>> +
>> + if (slot_state <= SLOT_STATE_DEFAULT)
>> + return 0;
>> +
>> + cdnsp_queue_reset_device(pdev);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> +
>> + /*
>> + * After Reset Device command all not default endpoints
>> + * are in Disabled state.
>> + */
>> + for (i = 1; i < 31; ++i)
>> + pdev->eps[i].ep_state |= EP_STOPPED;
>> +
>> + if (ret)
>> + dev_err(pdev->dev, "Reset device failed with error code %d",
>> + ret);
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * Sets the MaxPStreams field and the Linear Stream Array field.
>> + * Sets the dequeue pointer to the stream context array.
>> + */
>> +static void cdnsp_setup_streams_ep_input_ctx(struct cdnsp_device *pdev,
>> + struct cdnsp_ep_ctx *ep_ctx,
>> + struct cdnsp_stream_info *stream_info)
>> +{
>> + u32 max_primary_streams;
>> +
>> + /* MaxPStreams is the number of stream context array entries, not the
>> + * number we're actually using. Must be in 2^(MaxPstreams + 1) format.
>> + * fls(0) = 0, fls(0x1) = 1, fls(0x10) = 2, fls(0x100) = 3, etc.
>> + */
>> + max_primary_streams = fls(stream_info->num_stream_ctxs) - 2;
>> + ep_ctx->ep_info &= cpu_to_le32(~EP_MAXPSTREAMS_MASK);
>> + ep_ctx->ep_info |= cpu_to_le32(EP_MAXPSTREAMS(max_primary_streams)
>> + | EP_HAS_LSA);
>> + ep_ctx->deq = cpu_to_le64(stream_info->ctx_array_dma);
>> +}
>> +
>> +/*
>> + * The drivers use this function to prepare a bulk endpoints to use streams.
>> + *
>> + * Don't allow the call to succeed if endpoint only supports one stream
>> + * (which means it doesn't support streams at all).
>> + */
>> +int cdnsp_alloc_streams(struct cdnsp_device *pdev, struct cdnsp_ep *pep)
>> +{
>> + unsigned int num_streams = usb_ss_max_streams(pep->endpoint.comp_desc);
>> + unsigned int num_stream_ctxs;
>> + int ret;
>> +
>> + if (num_streams == 0)
>> + return 0;
>> +
>> + if (num_streams > STREAM_NUM_STREAMS)
>> + return -EINVAL;
>> +
>> + /*
>> + * Add two to the number of streams requested to account for
>> + * stream 0 that is reserved for controller usage and one additional
>> + * for TASK SET FULL response.
>> + */
>> + num_streams += 2;
>> +
>> + /* The stream context array size must be a power of two */
>> + num_stream_ctxs = roundup_pow_of_two(num_streams);
>> +
>> + ret = cdnsp_alloc_stream_info(pdev, pep, num_stream_ctxs, num_streams);
>> + if (ret)
>> + return ret;
>> +
>> + cdnsp_setup_streams_ep_input_ctx(pdev, pep->in_ctx, &pep->stream_info);
>> +
>> + pep->ep_state |= EP_HAS_STREAMS;
>> + pep->stream_info.td_count = 0;
>> + pep->stream_info.first_prime_det = 0;
>> +
>> + /* Subtract 1 for stream 0, which drivers can't use. */
>> + return num_streams - 1;
>> +}
>> +
>> +int cdnsp_disable_slot(struct cdnsp_device *pdev)
>> +{
>> + int ret;
>> +
>> + cdnsp_queue_slot_control(pdev, TRB_DISABLE_SLOT);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> +
>> + pdev->slot_id = 0;
>> + pdev->active_port = NULL;
>> +
>> + memset(pdev->in_ctx.bytes, 0, CDNSP_CTX_SIZE);
>> + memset(pdev->out_ctx.bytes, 0, CDNSP_CTX_SIZE);
>> +
>> + return ret;
>> +}
>> +
>> +int cdnsp_enable_slot(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + int slot_state;
>> + int ret;
>> +
>> + /* If device is not setup, there is no point in resetting it */
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx);
>> + slot_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state));
>> +
>> + if (slot_state != SLOT_STATE_DISABLED)
>> + return 0;
>> +
>> + cdnsp_queue_slot_control(pdev, TRB_ENABLE_SLOT);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> + if (ret)
>> + return ret;
>> +
>> + pdev->slot_id = 1;
>> +
>> + return 0;
>> +}
>> +
>> +/*
>> + * Issue an Address Device command with BSR=0 if setup is SETUP_CONTEXT_ONLY
>> + * or with BSR = 1 if set_address is SETUP_CONTEXT_ADDRESS.
>> + */
>> +int cdnsp_setup_device(struct cdnsp_device *pdev, enum cdnsp_setup_dev setup)
>> +{
>> + struct cdnsp_input_control_ctx *ctrl_ctx;
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + int dev_state = 0;
>> + int ret;
>> +
>> + if (!pdev->slot_id)
>> + return -EINVAL;
>> +
>> + if (!pdev->active_port->port_num)
>> + return -EINVAL;
>> +
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx);
>> + dev_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state));
>> +
>> + if (setup == SETUP_CONTEXT_ONLY && dev_state == SLOT_STATE_DEFAULT)
>> + return 0;
>> +
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx);
>> + ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx);
>> +
>> + if (!slot_ctx->dev_info || dev_state == SLOT_STATE_DEFAULT) {
>> + ret = cdnsp_setup_addressable_priv_dev(pdev);
>> + if (ret)
>> + return ret;
>> + }
>> +
>> + cdnsp_copy_ep0_dequeue_into_input_ctx(pdev);
>> +
>> + ctrl_ctx->add_flags = cpu_to_le32(SLOT_FLAG | EP0_FLAG);
>> + ctrl_ctx->drop_flags = 0;
>> +
>> + cdnsp_queue_address_device(pdev, pdev->in_ctx.dma, setup);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> +
>> + /* Zero the input context control for later use. */
>> + ctrl_ctx->add_flags = 0;
>> + ctrl_ctx->drop_flags = 0;
>> +
>> + return ret;
>> +}
>> +
>> +void cdnsp_set_usb2_hardware_lpm(struct cdnsp_device *pdev,
>> + struct usb_request *req,
>> + int enable)
>> +{
>> + if (pdev->active_port != &pdev->usb2_port || !pdev->gadget.lpm_capable)
>> + return;
>> +
>> + if (enable)
>> + writel(PORT_BESL(CDNSP_DEFAULT_BESL) | PORT_L1S_NYET | PORT_HLE,
>> + &pdev->active_port->regs->portpmsc);
>> + else
>> + writel(PORT_L1S_NYET, &pdev->active_port->regs->portpmsc);
>> +}
>> +
>> +static int cdnsp_get_frame(struct cdnsp_device *pdev)
>> +{
>> + return readl(&pdev->run_regs->microframe_index) >> 3;
>> +}
>> +
>> +static int cdnsp_gadget_ep_enable(struct usb_ep *ep,
>> + const struct usb_endpoint_descriptor *desc)
>> +{
>> + struct cdnsp_input_control_ctx *ctrl_ctx;
>> + struct cdnsp_device *pdev;
>> + struct cdnsp_ep *pep;
>> + unsigned long flags;
>> + u32 added_ctxs;
>> + int ret;
>> +
>> + if (!ep || !desc || desc->bDescriptorType != USB_DT_ENDPOINT ||
>> + !desc->wMaxPacketSize)
>> + return -EINVAL;
>> +
>> + pep = to_cdnsp_ep(ep);
>> + pdev = pep->pdev;
>> +
>> + if (dev_WARN_ONCE(pdev->dev, pep->ep_state & EP_ENABLED,
>> + "%s is already enabled\n", pep->name))
>> + return 0;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> +
>> + added_ctxs = cdnsp_get_endpoint_flag(desc);
>> + if (added_ctxs == SLOT_FLAG || added_ctxs == EP0_FLAG) {
>> + dev_err(pdev->dev, "ERROR: Bad endpoint number\n");
>> + ret = -EINVAL;
>> + goto unlock;
>> + }
>> +
>> + pep->interval = desc->bInterval ? BIT(desc->bInterval - 1) : 0;
>> +
>> + if (pdev->gadget.speed == USB_SPEED_FULL) {
>> + if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_INT)
>> + pep->interval = desc->bInterval << 3;
>> + if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_ISOC)
>> + pep->interval = BIT(desc->bInterval - 1) << 3;
>> + }
>> +
>> + if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_ISOC) {
>> + if (pep->interval > BIT(12)) {
>> + dev_err(pdev->dev, "bInterval %d not supported\n",
>> + desc->bInterval);
>> + ret = -EINVAL;
>> + goto unlock;
>> + }
>> + cdnsp_set_chicken_bits_2(pdev, CHICKEN_XDMA_2_TP_CACHE_DIS);
>> + }
>> +
>> + ret = cdnsp_endpoint_init(pdev, pep, GFP_ATOMIC);
>> + if (ret)
>> + goto unlock;
>> +
>> + ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx);
>> + ctrl_ctx->add_flags = cpu_to_le32(added_ctxs);
>> + ctrl_ctx->drop_flags = 0;
>> +
>> + ret = cdnsp_update_eps_configuration(pdev, pep);
>> + if (ret) {
>> + cdnsp_free_endpoint_rings(pdev, pep);
>> + goto unlock;
>> + }
>> +
>> + pep->ep_state |= EP_ENABLED;
>> + pep->ep_state &= ~EP_STOPPED;
>> +
>> +unlock:
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +static int cdnsp_gadget_ep_disable(struct usb_ep *ep)
>> +{
>> + struct cdnsp_input_control_ctx *ctrl_ctx;
>> + struct cdnsp_request *preq;
>> + struct cdnsp_device *pdev;
>> + struct cdnsp_ep *pep;
>> + unsigned long flags;
>> + u32 drop_flag;
>> + int ret = 0;
>> +
>> + if (!ep)
>> + return -EINVAL;
>> +
>> + pep = to_cdnsp_ep(ep);
>> + pdev = pep->pdev;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> +
>> + if (!(pep->ep_state & EP_ENABLED)) {
>> + dev_err(pdev->dev, "%s is already disabled\n", pep->name);
>> + ret = -EINVAL;
>> + goto finish;
>> + }
>> +
>> + cdnsp_cmd_stop_ep(pdev, pep);
>> + pep->ep_state |= EP_DIS_IN_RROGRESS;
>> + cdnsp_cmd_flush_ep(pdev, pep);
>> +
>> + /* Remove all queued USB requests. */
>> + while (!list_empty(&pep->pending_list)) {
>> + preq = next_request(&pep->pending_list);
>> + cdnsp_ep_dequeue(pep, preq);
>> + }
>> +
>> + cdnsp_invalidate_ep_events(pdev, pep);
>> +
>> + pep->ep_state &= ~EP_DIS_IN_RROGRESS;
>> + drop_flag = cdnsp_get_endpoint_flag(pep->endpoint.desc);
>> + ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx);
>> + ctrl_ctx->drop_flags = cpu_to_le32(drop_flag);
>> + ctrl_ctx->add_flags = 0;
>> +
>> + cdnsp_endpoint_zero(pdev, pep);
>> +
>> + ret = cdnsp_update_eps_configuration(pdev, pep);
>> + cdnsp_free_endpoint_rings(pdev, pep);
>> +
>> + pep->ep_state &= ~EP_ENABLED;
>> + pep->ep_state |= EP_STOPPED;
>> +
>> +finish:
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +static struct usb_request *cdnsp_gadget_ep_alloc_request(struct usb_ep *ep,
>> + gfp_t gfp_flags)
>> +{
>> + struct cdnsp_ep *pep = to_cdnsp_ep(ep);
>> + struct cdnsp_request *preq;
>> +
>> + preq = kzalloc(sizeof(*preq), gfp_flags);
>> + if (!preq)
>> + return NULL;
>> +
>> + preq->epnum = pep->number;
>> + preq->pep = pep;
>> +
>> + return &preq->request;
>> +}
>> +
>> +static void cdnsp_gadget_ep_free_request(struct usb_ep *ep,
>> + struct usb_request *request)
>> +{
>> + struct cdnsp_request *preq = to_cdnsp_request(request);
>> +
>> + kfree(preq);
>> +}
>> +
>> +static int cdnsp_gadget_ep_queue(struct usb_ep *ep,
>> + struct usb_request *request,
>> + gfp_t gfp_flags)
>> +{
>> + struct cdnsp_request *preq;
>> + struct cdnsp_device *pdev;
>> + struct cdnsp_ep *pep;
>> + unsigned long flags;
>> + int ret;
>> +
>> + if (!request || !ep)
>> + return -EINVAL;
>> +
>> + pep = to_cdnsp_ep(ep);
>> + pdev = pep->pdev;
>> +
>> + if (!(pep->ep_state & EP_ENABLED)) {
>> + dev_err(pdev->dev, "%s: can't queue to disabled endpoint\n",
>> + pep->name);
>> + return -EINVAL;
>> + }
>> +
>> + preq = to_cdnsp_request(request);
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + ret = cdnsp_ep_enqueue(pep, preq);
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +static int cdnsp_gadget_ep_dequeue(struct usb_ep *ep,
>> + struct usb_request *request)
>> +{
>> + struct cdnsp_ep *pep = to_cdnsp_ep(ep);
>> + struct cdnsp_device *pdev = pep->pdev;
>> + unsigned long flags;
>> + int ret;
>> +
>> + if (!pep->endpoint.desc) {
>> + dev_err(pdev->dev,
>> + "%s: can't dequeue to disabled endpoint\n",
>> + pep->name);
>> + return -ESHUTDOWN;
>> + }
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + ret = cdnsp_ep_dequeue(pep, to_cdnsp_request(request));
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +static int cdnsp_gadget_ep_set_halt(struct usb_ep *ep, int value)
>> +{
>> + struct cdnsp_ep *pep = to_cdnsp_ep(ep);
>> + struct cdnsp_device *pdev = pep->pdev;
>> + struct cdnsp_request *preq;
>> + unsigned long flags = 0;
>> + int ret;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> +
>> + preq = next_request(&pep->pending_list);
>> + if (value) {
>> + if (preq) {
>> + ret = -EAGAIN;
>> + goto done;
>> + }
>> + }
>> +
>> + ret = cdnsp_halt_endpoint(pdev, pep, value);
>> +
>> +done:
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> + return ret;
>> +}
>> +
>> +static int cdnsp_gadget_ep_set_wedge(struct usb_ep *ep)
>> +{
>> + struct cdnsp_ep *pep = to_cdnsp_ep(ep);
>> + struct cdnsp_device *pdev = pep->pdev;
>> + unsigned long flags = 0;
>> + int ret;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + pep->ep_state |= EP_WEDGE;
>> + ret = cdnsp_halt_endpoint(pdev, pep, 1);
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +static const struct usb_ep_ops cdnsp_gadget_ep0_ops = {
>> + .enable = cdnsp_gadget_ep_enable,
>> + .disable = cdnsp_gadget_ep_disable,
>> + .alloc_request = cdnsp_gadget_ep_alloc_request,
>> + .free_request = cdnsp_gadget_ep_free_request,
>> + .queue = cdnsp_gadget_ep_queue,
>> + .dequeue = cdnsp_gadget_ep_dequeue,
>> + .set_halt = cdnsp_gadget_ep_set_halt,
>> + .set_wedge = cdnsp_gadget_ep_set_wedge,
>> +};
>> +
>> +static const struct usb_ep_ops cdnsp_gadget_ep_ops = {
>> + .enable = cdnsp_gadget_ep_enable,
>> + .disable = cdnsp_gadget_ep_disable,
>> + .alloc_request = cdnsp_gadget_ep_alloc_request,
>> + .free_request = cdnsp_gadget_ep_free_request,
>> + .queue = cdnsp_gadget_ep_queue,
>> + .dequeue = cdnsp_gadget_ep_dequeue,
>> + .set_halt = cdnsp_gadget_ep_set_halt,
>> + .set_wedge = cdnsp_gadget_ep_set_wedge,
>> +};
>> +
>> +void cdnsp_gadget_giveback(struct cdnsp_ep *pep,
>> + struct cdnsp_request *preq,
>> + int status)
>> +{
>> + struct cdnsp_device *pdev = pep->pdev;
>> +
>> + list_del(&preq->list);
>> +
>> + if (preq->request.status == -EINPROGRESS)
>> + preq->request.status = status;
>> +
>> + usb_gadget_unmap_request_by_dev(pdev->dev, &preq->request,
>> + preq->direction);
>> +
>> + if (preq != &pdev->ep0_preq) {
>> + spin_unlock(&pdev->lock);
>> + usb_gadget_giveback_request(&pep->endpoint, &preq->request);
>> + spin_lock(&pdev->lock);
>> + }
>> +}
>> +
>> +static struct usb_endpoint_descriptor cdnsp_gadget_ep0_desc = {
>> + .bLength = USB_DT_ENDPOINT_SIZE,
>> + .bDescriptorType = USB_DT_ENDPOINT,
>> + .bmAttributes = USB_ENDPOINT_XFER_CONTROL,
>> +};
>> +
>> +static int cdnsp_run(struct cdnsp_device *pdev,
>> + enum usb_device_speed speed)
>> +{
>> + u32 fs_speed = 0;
>> + u64 temp_64;
>> + u32 temp;
>> + int ret;
>> +
>> + temp_64 = cdnsp_read_64(pdev, &pdev->ir_set->erst_dequeue);
>> + temp_64 &= ~ERST_PTR_MASK;
>> + temp = readl(&pdev->ir_set->irq_control);
>> + temp &= ~IMOD_INTERVAL_MASK;
>> + temp |= ((IMOD_DEFAULT_INTERVAL / 250) & IMOD_INTERVAL_MASK);
>> + writel(temp, &pdev->ir_set->irq_control);
>> +
>> + temp = readl(&pdev->port3x_regs->mode_addr);
>> +
>> + switch (speed) {
>> + case USB_SPEED_SUPER_PLUS:
>> + temp |= CFG_3XPORT_SSP_SUPPORT;
>> + break;
>> + case USB_SPEED_SUPER:
>> + temp &= ~CFG_3XPORT_SSP_SUPPORT;
>> + break;
>> + case USB_SPEED_HIGH:
>> + break;
>> + case USB_SPEED_FULL:
>> + fs_speed = PORT_REG6_FORCE_FS;
>> + break;
>> + default:
>> + dev_err(pdev->dev, "invalid maximum_speed parameter %d\n",
>> + speed);
>> + fallthrough;
>> + case USB_SPEED_UNKNOWN:
>> + /* Default to superspeed. */
>> + speed = USB_SPEED_SUPER;
>> + break;
>> + }
>> +
>> + if (speed >= USB_SPEED_SUPER) {
>> + writel(temp, &pdev->port3x_regs->mode_addr);
>> + cdnsp_set_link_state(pdev, &pdev->usb3_port.regs->portsc,
>> + XDEV_RXDETECT);
>> + } else {
>> + cdnsp_disable_port(pdev, &pdev->usb3_port.regs->portsc);
>> + }
>> +
>> + cdnsp_set_link_state(pdev, &pdev->usb2_port.regs->portsc,
>> + XDEV_RXDETECT);
>> +
>> + cdnsp_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(512);
>> +
>> + writel(PORT_REG6_L1_L0_HW_EN | fs_speed, &pdev->port20_regs->port_reg6);
>> +
>> + ret = cdnsp_start(pdev);
>> + if (ret) {
>> + ret = -ENODEV;
>> + goto err;
>> + }
>> +
>> + temp = readl(&pdev->op_regs->command);
>> + temp |= (CMD_INTE);
>> + writel(temp, &pdev->op_regs->command);
>> +
>> + temp = readl(&pdev->ir_set->irq_pending);
>> + writel(IMAN_IE_SET(temp), &pdev->ir_set->irq_pending);
>> +
>> + return 0;
>> +err:
>> + cdnsp_halt(pdev);
>> + return ret;
>> +}
>> +
>> +static int cdnsp_gadget_udc_start(struct usb_gadget *g,
>> + struct usb_gadget_driver *driver)
>> +{
>> + enum usb_device_speed max_speed = driver->max_speed;
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(g);
>> + unsigned long flags;
>> + int ret;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + pdev->gadget_driver = driver;
>> +
>> + /* limit speed if necessary */
>> + max_speed = min(driver->max_speed, g->max_speed);
>> + ret = cdnsp_run(pdev, max_speed);
>> +
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * Update Event Ring Dequeue Pointer:
>> + * - When all events have finished
>> + * - To avoid "Event Ring Full Error" condition
>> + */
>> +void cdnsp_update_erst_dequeue(struct cdnsp_device *pdev,
>> + union cdnsp_trb *event_ring_deq,
>> + u8 clear_ehb)
>> +{
>> + u64 temp_64;
>> + dma_addr_t deq;
>> +
>> + temp_64 = cdnsp_read_64(pdev, &pdev->ir_set->erst_dequeue);
>> +
>> + /* If necessary, update the HW's version of the event ring deq ptr. */
>> + if (event_ring_deq != pdev->event_ring->dequeue) {
>> + deq = cdnsp_trb_virt_to_dma(pdev->event_ring->deq_seg,
>> + pdev->event_ring->dequeue);
>> + temp_64 &= ERST_PTR_MASK;
>> + temp_64 |= ((u64)deq & (u64)~ERST_PTR_MASK);
>> + }
>> +
>> + /* Clear the event handler busy flag (RW1C). */
>> + if (clear_ehb)
>> + temp_64 |= ERST_EHB;
>> + else
>> + temp_64 &= ~ERST_EHB;
>> +
>> + cdnsp_write_64(pdev, temp_64, &pdev->ir_set->erst_dequeue);
>> +}
>> +
>> +static void cdnsp_clear_cmd_ring(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_segment *seg;
>> + u64 val_64;
>> + int i;
>> +
>> + cdnsp_initialize_ring_info(pdev->cmd_ring);
>> +
>> + seg = pdev->cmd_ring->first_seg;
>> + for (i = 0; i < pdev->cmd_ring->num_segs; i++) {
>> + memset(seg->trbs, 0,
>> + sizeof(union cdnsp_trb) * (TRBS_PER_SEGMENT - 1));
>> + seg = seg->next;
>> + }
>> +
>> + /* Set the address in the Command Ring Control register. */
>> + val_64 = cdnsp_read_64(pdev, &pdev->op_regs->cmd_ring);
>> + val_64 = (val_64 & (u64)CMD_RING_RSVD_BITS) |
>> + (pdev->cmd_ring->first_seg->dma & (u64)~CMD_RING_RSVD_BITS) |
>> + pdev->cmd_ring->cycle_state;
>> + cdnsp_write_64(pdev, val_64, &pdev->op_regs->cmd_ring);
>> +}
>> +
>> +static void cdnsp_consume_all_events(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_segment *event_deq_seg;
>> + union cdnsp_trb *event_ring_deq;
>> + union cdnsp_trb *event;
>> + u32 cycle_bit;
>> +
>> + event_ring_deq = pdev->event_ring->dequeue;
>> + event_deq_seg = pdev->event_ring->deq_seg;
>> + event = pdev->event_ring->dequeue;
>> +
>> + /* Update ring dequeue pointer. */
>> + while (1) {
>> + cycle_bit = (le32_to_cpu(event->event_cmd.flags) & TRB_CYCLE);
>> +
>> + /* Does the controller or driver own the TRB? */
>> + if (cycle_bit != pdev->event_ring->cycle_state)
>> + break;
>> +
>> + cdnsp_inc_deq(pdev, pdev->event_ring);
>> +
>> + if (!cdnsp_last_trb_on_seg(event_deq_seg, event)) {
>> + event++;
>> + continue;
>> + }
>> +
>> + if (cdnsp_last_trb_on_ring(pdev->event_ring, event_deq_seg,
>> + event))
>> + cycle_bit ^= 1;
>> +
>> + event_deq_seg = event_deq_seg->next;
>> + event = event_deq_seg->trbs;
>> + }
>> +
>> + cdnsp_update_erst_dequeue(pdev, event_ring_deq, 1);
>> +}
>> +
>> +static void cdnsp_stop(struct cdnsp_device *pdev)
>> +{
>> + u32 temp;
>> +
>> + cdnsp_cmd_flush_ep(pdev, &pdev->eps[0]);
>> +
>> + /* Remove internally queued request for ep0. */
>> + if (!list_empty(&pdev->eps[0].pending_list)) {
>> + struct cdnsp_request *req;
>> +
>> + req = next_request(&pdev->eps[0].pending_list);
>> + if (req == &pdev->ep0_preq)
>> + cdnsp_ep_dequeue(&pdev->eps[0], req);
>> + }
>> +
>> + cdnsp_disable_port(pdev, &pdev->usb2_port.regs->portsc);
>> + cdnsp_disable_port(pdev, &pdev->usb3_port.regs->portsc);
>> + cdnsp_disable_slot(pdev);
>> + cdnsp_halt(pdev);
>> +
>> + temp = readl(&pdev->op_regs->status);
>> + writel((temp & ~0x1fff) | STS_EINT, &pdev->op_regs->status);
>> + temp = readl(&pdev->ir_set->irq_pending);
>> + writel(IMAN_IE_CLEAR(temp), &pdev->ir_set->irq_pending);
>> +
>> + cdnsp_clear_port_change_bit(pdev, &pdev->usb2_port.regs->portsc);
>> + cdnsp_clear_port_change_bit(pdev, &pdev->usb3_port.regs->portsc);
>> +
>> + /*Clear interrupt line */
>> + temp = readl(&pdev->ir_set->irq_pending);
>> + temp |= IMAN_IP;
>> + writel(temp, &pdev->ir_set->irq_pending);
>> +
>> + cdnsp_consume_all_events(pdev);
>> + cdnsp_clear_cmd_ring(pdev);
>> +}
>> +
>> +/*
>> + * Stop controller.
>> + * This function is called by the gadget core when the driver is removed.
>> + * Disable slot, disable IRQs, and quiesce the controller.
>> + */
>> +static int cdnsp_gadget_udc_stop(struct usb_gadget *g)
>> +{
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(g);
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + cdnsp_stop(pdev);
>> + pdev->gadget_driver = NULL;
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_gadget_get_frame(struct usb_gadget *g)
>> +{
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(g);
>> +
>> + return cdnsp_get_frame(pdev);
>> +}
>> +
>> +static void __cdnsp_gadget_wakeup(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_port_regs __iomem *port_regs;
>> + u32 portpm, portsc;
>> +
>> + port_regs = pdev->active_port->regs;
>> + portsc = readl(&port_regs->portsc) & PORT_PLS_MASK;
>> +
>> + /* Remote wakeup feature is not enabled by host. */
>> + if (pdev->gadget.speed < USB_SPEED_SUPER && portsc == XDEV_U2) {
>> + portpm = readl(&port_regs->portpmsc);
>> +
>> + if (!(portpm & PORT_RWE))
>> + return;
>> + }
>> +
>> + if (portsc == XDEV_U3 && !pdev->may_wakeup)
>> + return;
>> +
>> + cdnsp_set_link_state(pdev, &port_regs->portsc, XDEV_U0);
>> +
>> + pdev->cdnsp_state |= CDNSP_WAKEUP_PENDING;
>> +}
>> +
>> +static int cdnsp_gadget_wakeup(struct usb_gadget *g)
>> +{
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(g);
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + __cdnsp_gadget_wakeup(pdev);
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_gadget_set_selfpowered(struct usb_gadget *g,
>> + int is_selfpowered)
>> +{
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(g);
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + g->is_selfpowered = !!is_selfpowered;
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_gadget_pullup(struct usb_gadget *gadget, int is_on)
>> +{
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(gadget);
>> + struct cdns *cdns = dev_get_drvdata(pdev->dev);
>> +
>> + if (!is_on) {
>> + cdnsp_reset_device(pdev);
>> + cdns_clear_vbus(cdns);
>> + } else {
>> + cdns_set_vbus(cdns);
>> + }
>> + return 0;
>> +}
>> +
>> +const struct usb_gadget_ops cdnsp_gadget_ops = {
>> + .get_frame = cdnsp_gadget_get_frame,
>> + .wakeup = cdnsp_gadget_wakeup,
>> + .set_selfpowered = cdnsp_gadget_set_selfpowered,
>> + .pullup = cdnsp_gadget_pullup,
>> + .udc_start = cdnsp_gadget_udc_start,
>> + .udc_stop = cdnsp_gadget_udc_stop,
>> +};
>> +
>> +static void cdnsp_get_ep_buffering(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep)
>> +{
>> + void __iomem *reg = &pdev->cap_regs->hc_capbase;
>> + int endpoints;
>> +
>> + reg += cdnsp_find_next_ext_cap(reg, 0, XBUF_CAP_ID);
>> +
>> + if (!pep->direction) {
>> + pep->buffering = readl(reg + XBUF_RX_TAG_MASK_0_OFFSET);
>> + pep->buffering_period = readl(reg + XBUF_RX_TAG_MASK_1_OFFSET);
>> + pep->buffering = (pep->buffering + 1) / 2;
>> + pep->buffering_period = (pep->buffering_period + 1) / 2;
>> + return;
>> + }
>> +
>> + endpoints = HCS_ENDPOINTS(readl(&pdev->hcs_params1)) / 2;
>> +
>> + /* Set to XBUF_TX_TAG_MASK_0 register. */
>> + reg += XBUF_TX_CMD_OFFSET + (endpoints * 2 + 2) * sizeof(u32);
>> + /* Set reg to XBUF_TX_TAG_MASK_N related with this endpoint. */
>> + reg += pep->number * sizeof(u32) * 2;
>> +
>> + pep->buffering = (readl(reg) + 1) / 2;
>> + pep->buffering_period = pep->buffering;
>> +}
>> +
>> +static int cdnsp_gadget_init_endpoints(struct cdnsp_device *pdev)
>> +{
>> + int max_streams = HCC_MAX_PSA(pdev->hcc_params);
>> + struct cdnsp_ep *pep;
>> + int i;
>> +
>> + INIT_LIST_HEAD(&pdev->gadget.ep_list);
>> +
>> + if (max_streams < STREAM_LOG_STREAMS) {
>> + dev_err(pdev->dev, "Stream size %d not supported\n",
>> + max_streams);
>> + return -EINVAL;
>> + }
>> +
>> + max_streams = STREAM_LOG_STREAMS;
>> +
>> + for (i = 0; i < CDNSP_ENDPOINTS_NUM; i++) {
>> + bool direction = !(i & 1); /* Start from OUT endpoint. */
>> + u8 epnum = ((i + 1) >> 1);
>> +
>> + if (!CDNSP_IF_EP_EXIST(pdev, epnum, direction))
>> + continue;
>> +
>> + pep = &pdev->eps[i];
>> + pep->pdev = pdev;
>> + pep->number = epnum;
>> + pep->direction = direction; /* 0 for OUT, 1 for IN. */
>> +
>> + /*
>> + * Ep0 is bidirectional, so ep0in and ep0out are represented by
>> + * pdev->eps[0]
>> + */
>> + if (epnum == 0) {
>> + snprintf(pep->name, sizeof(pep->name), "ep%d%s",
>> + epnum, "BiDir");
>> +
>> + pep->idx = 0;
>> + usb_ep_set_maxpacket_limit(&pep->endpoint, 512);
>> + pep->endpoint.maxburst = 1;
>> + pep->endpoint.ops = &cdnsp_gadget_ep0_ops;
>> + pep->endpoint.desc = &cdnsp_gadget_ep0_desc;
>> + pep->endpoint.comp_desc = NULL;
>> + pep->endpoint.caps.type_control = true;
>> + pep->endpoint.caps.dir_in = true;
>> + pep->endpoint.caps.dir_out = true;
>> +
>> + pdev->ep0_preq.epnum = pep->number;
>> + pdev->ep0_preq.pep = pep;
>> + pdev->gadget.ep0 = &pep->endpoint;
>> + } else {
>> + snprintf(pep->name, sizeof(pep->name), "ep%d%s",
>> + epnum, (pep->direction) ? "in" : "out");
>there is two blank space after "in", please use checkpatch.pl with
>--strict

I always use checkpsatch.pl with --strict option. It didn't complain
for this case.

<snip>

Thanks,
Pawel

>>

2020-09-30 13:04:18

by Pawel Laszczak

[permalink] [raw]

Subject: RE: [PATCH 7/8] usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver

>
>On 20-09-28 14:27:40, Pawel Laszczak wrote:
>> This patch introduces the main part of Cadence USBSSP DRD driver
>> to Linux kernel.
>> To reduce the patch size a little bit, the header file gadget.h was
>> intentionally added as separate patch.
>>
>> The Cadence USBSSP DRD Controller is a highly configurable IP Core which
>> can be instantiated as Dual-Role Device (DRD), Peripheral Only and
>> Host Only (XHCI)configurations.
>>
>> The current driver has been validated with FPGA platform. We have
>> support for PCIe bus, which is used on FPGA prototyping.
>>
>> The host side of USBSS DRD controller is compliant with XHCI.
>> The architecture for device side is almost the same as for host side,
>> and most of the XHCI specification can be used to understand how
>> this controller operates.
>>
>> Signed-off-by: Pawel Laszczak <[email protected]>
>> ---
>> drivers/usb/Kconfig | 1 +
>> drivers/usb/Makefile | 1 +
>> drivers/usb/cdns3/core.c | 19 +-
>> drivers/usb/cdns3/drd.c | 28 +
>> drivers/usb/cdns3/drd.h | 2 +
>> drivers/usb/cdns3/gadget-export.h | 18 +-
>> drivers/usb/cdns3/host-export.h | 4 +-
>> drivers/usb/cdnsp/Kconfig | 40 +
>> drivers/usb/cdnsp/Makefile | 7 +
>> drivers/usb/cdnsp/cdnsp-pci.c | 247 +++
>> drivers/usb/cdnsp/ep0.c | 480 ++++++
>> drivers/usb/cdnsp/gadget.c | 1946 ++++++++++++++++++++++++
>> drivers/usb/cdnsp/gadget.h | 139 ++
>> drivers/usb/cdnsp/mem.c | 1312 ++++++++++++++++
>> drivers/usb/cdnsp/ring.c | 2363 +++++++++++++++++++++++++++++
>
>Pawel, I think you may put cdnsp stuff under the folder
>of cdns3. It is may not be suitable there are two IP drivers folder
>under the root of usb.
>
>You could create files like below:
>cdns3-ep0.c
>cdns3-gadget.c
>cdns3-gadget.h
>
>cdnsp-ep0.c
>cdnsp-gadget.c
>cdnsp-gadget.h
>cdnsp-mem.c
>cdnsp-ring.c

I thought about this, but I was afraid that someone could complain
if I put two quite large driver in the same directory.
Also, I didn't want to make to big revolution in cdns3.

The other option is to put them in separate sub-directories:
cdns3 - it should be changed
- cdns3
- cdnsp
- common files.

It can be done even after upstreaming cdnsp driver.

>
>Besides, what's the difference between cdnsp-pci.c and current
>cdns3-pci-wrap.c, does host controller also be changed?
>

The main difference is that cdns3-pci-wrap.c is a wrapper and
create and register platform device.
The cdnsp-pci.c is a pure PCI driver.

BTW I have one issue with reusing code. We have three drivers (modules)
cdns3
cdnsp-udc-pci
cdns-usb-common

Modules cdns3 and cdnsp-udc-pci depend on cdns-usb-common and vice versa
and It causes that I cannot create such circular dependencies in Kconfig files.

If kernel configuration enable both drivers then all modules must be buil in kernel
or all must compiled as module. I can't find the way for such restriction in Kconfig.

Regards,
Pawel

>
>> 15 files changed, 6600 insertions(+), 7 deletions(-)
>> create mode 100644 drivers/usb/cdnsp/Kconfig
>> create mode 100644 drivers/usb/cdnsp/Makefile
>> create mode 100644 drivers/usb/cdnsp/cdnsp-pci.c
>> create mode 100644 drivers/usb/cdnsp/ep0.c
>> create mode 100644 drivers/usb/cdnsp/gadget.c
>> create mode 100644 drivers/usb/cdnsp/mem.c
>> create mode 100644 drivers/usb/cdnsp/ring.c
>>
>> diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
>> index 26475b409b53..555c4a4cb465 100644
>> --- a/drivers/usb/Kconfig
>> +++ b/drivers/usb/Kconfig
>> @@ -112,6 +112,7 @@ source "drivers/usb/usbip/Kconfig"
>> endif
>>
>> source "drivers/usb/cdns3/Kconfig"
>> +source "drivers/usb/cdnsp/Kconfig"
>>
>> source "drivers/usb/mtu3/Kconfig"
>>
>> diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile
>> index 1c1c1d659394..84727f7a4b92 100644
>> --- a/drivers/usb/Makefile
>> +++ b/drivers/usb/Makefile
>> @@ -14,6 +14,7 @@ obj-$(CONFIG_USB_DWC2) += dwc2/
>> obj-$(CONFIG_USB_ISP1760) += isp1760/
>>
>> obj-$(CONFIG_USB_CDNS3) += cdns3/
>> +obj-$(CONFIG_USB_CDNSP) += cdnsp/
>>
>> obj-$(CONFIG_USB_MON) += mon/
>> obj-$(CONFIG_USB_MTU3) += mtu3/
>> diff --git a/drivers/usb/cdns3/core.c b/drivers/usb/cdns3/core.c
>> index 2af99294beaa..560783092d8a 100644
>> --- a/drivers/usb/cdns3/core.c
>> +++ b/drivers/usb/cdns3/core.c
>> @@ -138,7 +138,14 @@ static int cdns_core_init_role(struct cdns *cdns)
>> dr_mode = best_dr_mode;
>>
>> if (dr_mode == USB_DR_MODE_OTG || dr_mode == USB_DR_MODE_HOST) {
>> - ret = cdns_host_init(cdns);
>> + if ((cdns->version == CDNSP_CONTROLLER_V2 &&
>> + IS_ENABLED(CONFIG_USB_CDNSP_HOST)) ||
>> + (cdns->version < CDNSP_CONTROLLER_V2 &&
>> + IS_ENABLED(CONFIG_USB_CDNS3_HOST)))
>> + ret = cdns_host_init(cdns);
>> + else
>> + ret = -ENXIO;
>> +
>> if (ret) {
>> dev_err(dev, "Host initialization failed with %d\n",
>> ret);
>> @@ -147,7 +154,15 @@ static int cdns_core_init_role(struct cdns *cdns)
>> }
>>
>> if (dr_mode == USB_DR_MODE_OTG || dr_mode == USB_DR_MODE_PERIPHERAL) {
>> - ret = cdns3_gadget_init(cdns);
>> + if (cdns->version == CDNSP_CONTROLLER_V2 &&
>> + IS_ENABLED(CONFIG_USB_CDNSP_GADGET))
>> + ret = cdnsp_gadget_init(cdns);
>> + else if (cdns->version < CDNSP_CONTROLLER_V2 &&
>> + IS_ENABLED(CONFIG_USB_CDNS3_GADGET))
>> + ret = cdns3_gadget_init(cdns);
>> + else
>> + ret = -ENXIO;
>> +
>> if (ret) {
>> dev_err(dev, "Device initialization failed with %d\n",
>> ret);
>> diff --git a/drivers/usb/cdns3/drd.c b/drivers/usb/cdns3/drd.c
>> index 7feb622972da..3c732e19c61c 100644
>> --- a/drivers/usb/cdns3/drd.c
>> +++ b/drivers/usb/cdns3/drd.c
>> @@ -90,6 +90,32 @@ int cdns_get_vbus(struct cdns *cdns)
>> return vbus;
>> }
>>
>> +void cdns_clear_vbus(struct cdns *cdns)
>> +{
>> + u32 reg;
>> +
>> + if (cdns->version != CDNSP_CONTROLLER_V2)
>> + return;
>> +
>> + reg = readl(&cdns->otg_cdnsp_regs->override);
>> + reg |= OVERRIDE_SESS_VLD_SEL;
>> + writel(reg, &cdns->otg_cdnsp_regs->override);
>> +}
>> +EXPORT_SYMBOL_GPL(cdns_clear_vbus);
>> +
>> +void cdns_set_vbus(struct cdns *cdns)
>> +{
>> + u32 reg;
>> +
>> + if (cdns->version != CDNSP_CONTROLLER_V2)
>> + return;
>> +
>> + reg = readl(&cdns->otg_cdnsp_regs->override);
>> + reg &= ~OVERRIDE_SESS_VLD_SEL;
>> + writel(reg, &cdns->otg_cdnsp_regs->override);
>> +}
>> +EXPORT_SYMBOL_GPL(cdns_set_vbus);
>> +
>> bool cdns_is_host(struct cdns *cdns)
>> {
>> if (cdns->dr_mode == USB_DR_MODE_HOST)
>> @@ -431,5 +457,7 @@ int cdns_drd_init(struct cdns *cdns)
>> int cdns_drd_exit(struct cdns *cdns)
>> {
>> cdns_otg_disable_irq(cdns);
>> + devm_free_irq(cdns->dev, cdns->otg_irq, cdns);
>> +
>> return 0;
>> }
>> diff --git a/drivers/usb/cdns3/drd.h b/drivers/usb/cdns3/drd.h
>> index b92e2834dc3f..7ef14bef047c 100644
>> --- a/drivers/usb/cdns3/drd.h
>> +++ b/drivers/usb/cdns3/drd.h
>> @@ -204,6 +204,8 @@ bool cdns_is_host(struct cdns *cdns);
>> bool cdns_is_device(struct cdns *cdns);
>> int cdns_get_id(struct cdns *cdns);
>> int cdns_get_vbus(struct cdns *cdns);
>> +extern void cdns_clear_vbus(struct cdns *cdns);
>> +extern void cdns_set_vbus(struct cdns *cdns);
>> int cdns_drd_init(struct cdns *cdns);
>> int cdns_drd_exit(struct cdns *cdns);
>> int cdns_drd_update_mode(struct cdns *cdns);
>> diff --git a/drivers/usb/cdns3/gadget-export.h b/drivers/usb/cdns3/gadget-export.h
>> index e784584fe053..b7eec9fb8fda 100644
>> --- a/drivers/usb/cdns3/gadget-export.h
>> +++ b/drivers/usb/cdns3/gadget-export.h
>> @@ -1,6 +1,6 @@
>> /* SPDX-License-Identifier: GPL-2.0 */
>> /*
>> - * Cadence USBSS DRD Driver - Gadget Export APIs.
>> + * Cadence USBSS and USBSSP DRD Driver - Gadget Export APIs.
>> *
>> * Copyright (C) 2017 NXP
>> * Copyright (C) 2017-2018 NXP
>> @@ -10,7 +10,19 @@
>> #ifndef __LINUX_CDNS3_GADGET_EXPORT
>> #define __LINUX_CDNS3_GADGET_EXPORT
>>
>> -#ifdef CONFIG_USB_CDNS3_GADGET
>> +#if IS_ENABLED(CONFIG_USB_CDNSP_GADGET)
>> +
>> +extern int cdnsp_gadget_init(struct cdns *cdns);
>> +#else
>> +
>> +static inline int cdnsp_gadget_init(struct cdns *cdns)
>> +{
>> + return -ENXIO;
>> +}
>> +
>> +#endif /* CONFIG_USB_CDNSP_GADGET */
>> +
>> +#if IS_ENABLED(CONFIG_USB_CDNS3_GADGET)
>>
>> extern int cdns3_gadget_init(struct cdns *cdns);
>> void cdns3_gadget_exit(struct cdns *cdns);
>> @@ -23,6 +35,6 @@ static inline int cdns3_gadget_init(struct cdns *cdns)
>>
>> static inline void cdns3_gadget_exit(struct cdns *cdns) { }
>>
>> -#endif
>> +#endif /* CONFIG_USB_CDNS3_GADGET */
>>
>> #endif /* __LINUX_CDNS3_GADGET_EXPORT */
>> diff --git a/drivers/usb/cdns3/host-export.h b/drivers/usb/cdns3/host-export.h
>> index d82b83d070ad..41f7ea1fed29 100644
>> --- a/drivers/usb/cdns3/host-export.h
>> +++ b/drivers/usb/cdns3/host-export.h
>> @@ -9,7 +9,7 @@
>> #ifndef __LINUX_CDNS3_HOST_EXPORT
>> #define __LINUX_CDNS3_HOST_EXPORT
>>
>> -#ifdef CONFIG_USB_CDNS3_HOST
>> +#if IS_ENABLED(CONFIG_USB_CDNS3_HOST) || IS_ENABLED(CONFIG_USB_CDNSP_GADGET)
>>
>> int cdns_host_init(struct cdns *cdns);
>>
>> @@ -22,6 +22,6 @@ static inline int cdns_host_init(struct cdns *cdns)
>>
>> static inline void cdns_host_exit(struct cdns *cdns) { }
>>
>> -#endif /* CONFIG_USB_CDNS3_HOST */
>> +#endif /* CONFIG_USB_CDNS3_HOST || CONFIG_USB_CDNSP_GADGET */
>>
>> #endif /* __LINUX_CDNS3_HOST_EXPORT */
>> diff --git a/drivers/usb/cdnsp/Kconfig b/drivers/usb/cdnsp/Kconfig
>> new file mode 100644
>> index 000000000000..56cee5f6dfb4
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/Kconfig
>> @@ -0,0 +1,40 @@
>> +config USB_CDNSP_PCI
>> + tristate "Cadence CDNSP Dual-Role Controller"
>> + depends on USB_SUPPORT && (USB || USB_GADGET) && HAS_DMA && USB_PCI && ACPI
>> + select USB_XHCI_PLATFORM if USB_XHCI_HCD
>> + select USB_ROLE_SWITCH
>> + select CDNS_USB_COMMON
>> + help
>> + Say Y here if your system has a Cadence CDNSP dual-role controller.
>> + It supports: dual-role switch Host-only, and Peripheral-only.
>> +
>> + If you choose to build this driver is a dynamically linked
>> + module, the module will be called cdnsp.ko.
>> +
>> +if USB_CDNSP_PCI
>> +
>> +config USB_CDNSP_GADGET
>> + bool "Cadence CDNSP device controller"
>> + depends on USB_GADGET=y || USB_GADGET=USB_CDNSP_PCI
>> + help
>> + Say Y here to enable device controller functionality of the
>> + Cadence CDNSP-DEV driver.
>> +
>> + Cadence CDNSP Device Controller in device mode is
>> + very similar to XHCI controller. Therefore some algorithms
>> + used has been taken from host driver.
>> + This controller supports FF, HS, SS and SSP mode.
>> + It doesn't support LS.
>> +
>> +config USB_CDNSP_HOST
>> + bool "Cadence CDNSP host controller"
>> + depends on USB=y || USB=USB_CDNSP_PCI
>> + select CDNS_USB_HOST
>> + help
>> + Say Y here to enable host controller functionality of the
>> + Cadence driver.
>> +
>> + Host controller is compliant with XHCI so it uses
>> + standard XHCI driver.
>> +
>> +endif
>> diff --git a/drivers/usb/cdnsp/Makefile b/drivers/usb/cdnsp/Makefile
>> new file mode 100644
>> index 000000000000..53202b21a8d2
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/Makefile
>> @@ -0,0 +1,7 @@
>> +# SPDX-License-Identifier: GPL-2.0
>> +
>> +cdnsp-udc-pci-y := cdnsp-pci.o
>> +
>> +obj-$(CONFIG_USB_CDNSP_PCI) += cdnsp-udc-pci.o
>> +cdnsp-udc-pci-$(CONFIG_USB_CDNSP_GADGET) += ring.o gadget.o mem.o ep0.o
>> +
>> diff --git a/drivers/usb/cdnsp/cdnsp-pci.c b/drivers/usb/cdnsp/cdnsp-pci.c
>> new file mode 100644
>> index 000000000000..f67ee8effcd3
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/cdnsp-pci.c
>> @@ -0,0 +1,247 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Cadence PCI Glue driver.
>> + *
>> + * Copyright (C) 2019 Cadence.
>> + *
>> + * Author: Pawel Laszczak <[email protected]>
>> + *
>> + */
>> +
>> +#include <linux/platform_device.h>
>> +#include <linux/dma-mapping.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/slab.h>
>> +#include <linux/pci.h>
>> +
>> +#include "../cdns3/core.h"
>> +
>> +#define PCI_BAR_HOST 0
>> +#define PCI_BAR_OTG 0
>> +#define PCI_BAR_DEV 2
>> +
>> +#define PCI_DEV_FN_HOST_DEVICE 0
>> +#define PCI_DEV_FN_OTG 1
>> +
>> +#define PCI_DRIVER_NAME "cdns-pci-usbssp"
>> +#define PLAT_DRIVER_NAME "cdns-usbssp"
>> +
>> +#define CDNS_VENDOR_ID 0x17cd
>> +#define CDNS_DEVICE_ID 0x0100
>> +#define CDNS_DRD_IF (PCI_CLASS_SERIAL_USB << 8 | 0x80)
>> +
>> +static struct pci_dev *cdnsp_get_second_fun(struct pci_dev *pdev)
>> +{
>> + struct pci_dev *func;
>> +
>> + /*
>> + * Gets the second function.
>> + * It's little tricky, but this platform has two function.
>> + * The fist keeps resources for Host/Device while the second
>> + * keeps resources for DRD/OTG.
>> + */
>> + func = pci_get_device(pdev->vendor, pdev->device, NULL);
>> + if (!func)
>> + return NULL;
>> +
>> + if (func->devfn == pdev->devfn) {
>> + func = pci_get_device(pdev->vendor, pdev->device, func);
>> + if (!func)
>> + return NULL;
>> + }
>> +
>> + return func;
>> +}
>> +
>> +static int cdnsp_pci_probe(struct pci_dev *pdev,
>> + const struct pci_device_id *id)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct pci_dev *func;
>> + struct resource *res;
>> + struct cdns *cdnsp;
>> + int ret;
>> +
>> + /*
>> + * For GADGET/HOST PCI (devfn) function number is 0,
>> + * for OTG PCI (devfn) function number is 1.
>> + */
>> + if (!id || (pdev->devfn != PCI_DEV_FN_HOST_DEVICE &&
>> + pdev->devfn != PCI_DEV_FN_OTG))
>> + return -EINVAL;
>> +
>> + func = cdnsp_get_second_fun(pdev);
>> + if (!func)
>> + return -EINVAL;
>> +
>> + if (func->class == PCI_CLASS_SERIAL_USB_XHCI ||
>> + pdev->class == PCI_CLASS_SERIAL_USB_XHCI) {
>> + ret = -EINVAL;
>> + goto put_pci;
>> + }
>> +
>> + ret = pcim_enable_device(pdev);
>> + if (ret) {
>> + dev_err(&pdev->dev, "Enabling PCI device has failed %d\n", ret);
>> + goto put_pci;
>> + }
>> +
>> + pci_set_master(pdev);
>> + if (pci_is_enabled(func)) {
>> + cdnsp = pci_get_drvdata(func);
>> + } else {
>> + cdnsp = kzalloc(sizeof(*cdnsp), GFP_KERNEL);
>> + if (!cdnsp) {
>> + ret = -ENOMEM;
>> + goto disable_pci;
>> + }
>> + }
>> +
>> + /* For GADGET device function number is 0. */
>> + if (pdev->devfn == 0) {
>> + resource_size_t rsrc_start, rsrc_len;
>> +
>> + /* Function 0: host(BAR_0) + device(BAR_1).*/
>> + dev_dbg(dev, "Initialize resources\n");
>> + rsrc_start = pci_resource_start(pdev, PCI_BAR_DEV);
>> + rsrc_len = pci_resource_len(pdev, PCI_BAR_DEV);
>> + res = devm_request_mem_region(dev, rsrc_start, rsrc_len, "dev");
>> + if (!res) {
>> + dev_dbg(dev, "controller already in use\n");
>> + ret = -EBUSY;
>> + goto free_cdnsp;
>> + }
>> +
>> + cdnsp->dev_regs = devm_ioremap(dev, rsrc_start, rsrc_len);
>> + if (!cdnsp->dev_regs) {
>> + dev_dbg(dev, "error mapping memory\n");
>> + ret = -EFAULT;
>> + goto free_cdnsp;
>> + }
>> +
>> + cdnsp->dev_irq = pdev->irq;
>> + dev_dbg(dev, "USBSS-DEV physical base addr: %pa\n",
>> + &rsrc_start);
>> +
>> + res = &cdnsp->xhci_res[0];
>> + res->start = pci_resource_start(pdev, PCI_BAR_HOST);
>> + res->end = pci_resource_end(pdev, PCI_BAR_HOST);
>> + res->name = "xhci";
>> + res->flags = IORESOURCE_MEM;
>> + dev_dbg(dev, "USBSS-XHCI physical base addr: %pa\n",
>> + &res->start);
>> +
>> + /* Interrupt for XHCI, */
>> + res = &cdnsp->xhci_res[1];
>> + res->start = pdev->irq;
>> + res->name = "host";
>> + res->flags = IORESOURCE_IRQ;
>> + } else {
>> + res = &cdnsp->otg_res;
>> + res->start = pci_resource_start(pdev, PCI_BAR_OTG);
>> + res->end = pci_resource_end(pdev, PCI_BAR_OTG);
>> + res->name = "otg";
>> + res->flags = IORESOURCE_MEM;
>> + dev_dbg(dev, "CDNSP-DRD physical base addr: %pa\n",
>> + &res->start);
>> +
>> + /* Interrupt for OTG/DRD. */
>> + cdnsp->otg_irq = pdev->irq;
>> + }
>> +
>> + if (pci_is_enabled(func)) {
>> + cdnsp->dev = dev;
>> +
>> + ret = cdns_init(cdnsp);
>> + if (ret)
>> + goto free_cdnsp;
>> + }
>> +
>> + pci_set_drvdata(pdev, cdnsp);
>> +
>> + device_wakeup_enable(&pdev->dev);
>> + if (pci_dev_run_wake(pdev))
>> + pm_runtime_put_noidle(&pdev->dev);
>> +
>> + return 0;
>> +
>> +free_cdnsp:
>> + if (!pci_is_enabled(func))
>> + kfree(cdnsp);
>> +
>> +disable_pci:
>> + pci_disable_device(pdev);
>> +
>> +put_pci:
>> + pci_dev_put(func);
>> +
>> + return ret;
>> +}
>> +
>> +static void cdnsp_pci_remove(struct pci_dev *pdev)
>> +{
>> + struct cdns *cdnsp;
>> + struct pci_dev *func;
>> +
>> + func = cdnsp_get_second_fun(pdev);
>> + cdnsp = (struct cdns *)pci_get_drvdata(pdev);
>> +
>> + if (pci_dev_run_wake(pdev))
>> + pm_runtime_get_noresume(&pdev->dev);
>> +
>> + if (!pci_is_enabled(func)) {
>> + kfree(cdnsp);
>> + goto pci_put;
>> + }
>> +
>> + cdns_remove(cdnsp);
>> +
>> +pci_put:
>> + pci_dev_put(func);
>> +}
>> +
>> +static int __maybe_unused cdnsp_pci_suspend(struct device *dev)
>> +{
>> + struct cdns *cdns = dev_get_drvdata(dev);
>> +
>> + return cdns_suspend(cdns);
>> +}
>> +
>> +static int __maybe_unused cdnsp_pci_resume(struct device *dev)
>> +{
>> + struct cdns *cdns = dev_get_drvdata(dev);
>> +
>> + return cdns_resume(cdns);
>> +}
>> +
>> +static const struct dev_pm_ops cdnsp_pci_pm_ops = {
>> + SET_SYSTEM_SLEEP_PM_OPS(cdnsp_pci_suspend, cdnsp_pci_resume)
>> +};
>> +
>> +static const struct pci_device_id cdnsp_pci_ids[] = {
>> + { PCI_VENDOR_ID_CDNS, CDNS_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,
>> + PCI_CLASS_SERIAL_USB_DEVICE, PCI_ANY_ID },
>> + { PCI_VENDOR_ID_CDNS, CDNS_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,
>> + CDNS_DRD_IF, PCI_ANY_ID },
>> + { 0, }
>> +};
>> +
>> +static struct pci_driver cdnsp_pci_driver = {
>> + .name = "cdnsp-pci",
>> + .id_table = &cdnsp_pci_ids[0],
>> + .probe = cdnsp_pci_probe,
>> + .remove = cdnsp_pci_remove,
>> + .driver = {
>> + .pm = &cdnsp_pci_pm_ops,
>> + }
>> +};
>> +
>> +module_pci_driver(cdnsp_pci_driver);
>> +MODULE_DEVICE_TABLE(pci, cdnsp_pci_ids);
>> +
>> +MODULE_ALIAS("pci:cdnsp");
>> +MODULE_AUTHOR("Pawel Laszczak <[email protected]>");
>> +MODULE_LICENSE("GPL v2");
>> +MODULE_DESCRIPTION("Cadence CDNSP PCI driver");
>> +
>> diff --git a/drivers/usb/cdnsp/ep0.c b/drivers/usb/cdnsp/ep0.c
>> new file mode 100644
>> index 000000000000..7f6e1d28d3b8
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/ep0.c
>> @@ -0,0 +1,480 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Cadence CDNSP DRD Driver.
>> + *
>> + * Copyright (C) 2020 Cadence.
>> + *
>> + * Author: Pawel Laszczak <[email protected]>
>> + *
>> + */
>> +
>> +#include <linux/usb/composite.h>
>> +#include <linux/usb/gadget.h>
>> +#include <linux/list.h>
>> +
>> +#include "gadget.h"
>> +
>> +static void cdnsp_ep0_stall(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_request *preq;
>> + struct cdnsp_ep *pep;
>> +
>> + pep = &pdev->eps[0];
>> + preq = next_request(&pep->pending_list);
>> +
>> + if (pdev->three_stage_setup) {
>> + cdnsp_halt_endpoint(pdev, pep, true);
>> +
>> + if (preq)
>> + cdnsp_gadget_giveback(pep, preq, -ECONNRESET);
>> + } else {
>> + pep->ep_state |= EP0_HALTED_STATUS;
>> +
>> + if (preq)
>> + list_del(&preq->list);
>> +
>> + cdnsp_status_stage(pdev);
>> + }
>> +}
>> +
>> +static int cdnsp_ep0_delegate_req(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + int ret;
>> +
>> + spin_unlock(&pdev->lock);
>> + ret = pdev->gadget_driver->setup(&pdev->gadget, ctrl);
>> + spin_lock(&pdev->lock);
>> +
>> + return ret;
>> +}
>> +
>> +static int cdnsp_ep0_set_config(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + enum usb_device_state state = pdev->gadget.state;
>> + u32 cfg;
>> + int ret;
>> +
>> + cfg = le16_to_cpu(ctrl->wValue);
>> +
>> + switch (state) {
>> + case USB_STATE_ADDRESS:
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> + if (ret)
>> + return ret;
>> + break;
>> + case USB_STATE_CONFIGURED:
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> + if (ret)
>> + return ret;
>> + break;
>> + default:
>> + dev_err(pdev->dev, "Set Configuration - bad device state\n");
>> + return -EINVAL;
>> + }
>> +
>> + if (!cfg)
>> + usb_gadget_set_state(&pdev->gadget, USB_STATE_ADDRESS);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_ep0_set_address(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + enum usb_device_state state = pdev->gadget.state;
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + unsigned int slot_state;
>> + int ret;
>> + u32 addr;
>> +
>> + addr = le16_to_cpu(ctrl->wValue);
>> +
>> + if (addr > 127) {
>> + dev_err(pdev->dev, "Invalid device address %d\n", addr);
>> + return -EINVAL;
>> + }
>> +
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx);
>> +
>> + if (state == USB_STATE_CONFIGURED) {
>> + dev_err(pdev->dev, "Can't Set Address from Configured State\n");
>> + return -EINVAL;
>> + }
>> +
>> + pdev->device_address = le16_to_cpu(ctrl->wValue);
>> +
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx);
>> + slot_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state));
>> + if (slot_state == SLOT_STATE_ADDRESSED)
>> + cdnsp_reset_device(pdev);
>> +
>> + /*set device address*/
>> + ret = cdnsp_setup_device(pdev, SETUP_CONTEXT_ADDRESS);
>> + if (ret)
>> + return ret;
>> +
>> + if (addr)
>> + usb_gadget_set_state(&pdev->gadget, USB_STATE_ADDRESS);
>> + else
>> + usb_gadget_set_state(&pdev->gadget, USB_STATE_DEFAULT);
>> +
>> + return 0;
>> +}
>> +
>> +int cdnsp_status_stage(struct cdnsp_device *pdev)
>> +{
>> + pdev->ep0_stage = CDNSP_STATUS_STAGE;
>> + pdev->ep0_preq.request.length = 0;
>> +
>> + return cdnsp_ep_enqueue(pdev->ep0_preq.pep, &pdev->ep0_preq);
>> +}
>> +
>> +static int cdnsp_w_index_to_ep_index(__le32 wIndex)
>> +{
>> + wIndex = le32_to_cpu(wIndex);
>> +
>> + if (!(wIndex & USB_ENDPOINT_NUMBER_MASK))
>> + return 0;
>> +
>> + return ((wIndex & USB_ENDPOINT_NUMBER_MASK) * 2) +
>> + (wIndex & USB_ENDPOINT_DIR_MASK ? 1 : 0) - 1;
>> +}
>> +
>> +static int cdnsp_ep0_handle_status(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + struct cdnsp_ep *pep;
>> + __le16 *response;
>> + int ep_sts = 0;
>> + u16 status = 0;
>> + u32 recipient;
>> +
>> + recipient = ctrl->bRequestType & USB_RECIP_MASK;
>> +
>> + switch (recipient) {
>> + case USB_RECIP_DEVICE:
>> + status = pdev->gadget.is_selfpowered;
>> + status |= pdev->may_wakeup << USB_DEVICE_REMOTE_WAKEUP;
>> +
>> + if (pdev->gadget.speed >= USB_SPEED_SUPER) {
>> + status |= pdev->u1_allowed << USB_DEV_STAT_U1_ENABLED;
>> + status |= pdev->u2_allowed << USB_DEV_STAT_U2_ENABLED;
>> + }
>> + break;
>> + case USB_RECIP_INTERFACE:
>> + /*
>> + * Function Remote Wake Capable D0
>> + * Function Remote Wakeup D1
>> + */
>> + return cdnsp_ep0_delegate_req(pdev, ctrl);
>> + case USB_RECIP_ENDPOINT:
>> + pep = &pdev->eps[cdnsp_w_index_to_ep_index(ctrl->wIndex)];
>> + ep_sts = GET_EP_CTX_STATE(pep->out_ctx);
>> +
>> + /* check if endpoint is stalled */
>> + if (ep_sts == EP_STATE_HALTED)
>> + status = BIT(USB_ENDPOINT_HALT);
>> + break;
>> + default:
>> + return -EINVAL;
>> + }
>> +
>> + response = (__le16 *)pdev->setup_buf;
>> + *response = cpu_to_le16(status);
>> +
>> + pdev->ep0_preq.request.length = sizeof(*response);
>> + pdev->ep0_preq.request.buf = pdev->setup_buf;
>> +
>> + return cdnsp_ep_enqueue(pdev->ep0_preq.pep, &pdev->ep0_preq);
>> +}
>> +
>> +static void cdnsp_enter_test_mode(struct cdnsp_device *pdev)
>> +{
>> + u32 temp;
>> +
>> + temp = readl(&pdev->active_port->regs->portpmsc) & ~GENMASK(31, 28);
>> + temp |= PORT_TEST_MODE(pdev->test_mode);
>> + writel(temp, &pdev->active_port->regs->portpmsc);
>> + pdev->test_mode = 0;
>> +}
>> +
>> +static int cdnsp_ep0_handle_feature_device(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl,
>> + int set)
>> +{
>> + enum usb_device_state state;
>> + enum usb_device_speed speed;
>> + u16 tmode;
>> +
>> + state = pdev->gadget.state;
>> + speed = pdev->gadget.speed;
>> +
>> + switch (le16_to_cpu(ctrl->wValue)) {
>> + case USB_DEVICE_REMOTE_WAKEUP:
>> + pdev->may_wakeup = !!set;
>> + break;
>> + case USB_DEVICE_U1_ENABLE:
>> + if (state != USB_STATE_CONFIGURED || speed < USB_SPEED_SUPER)
>> + return -EINVAL;
>> +
>> + pdev->u1_allowed = !!set;
>> + break;
>> + case USB_DEVICE_U2_ENABLE:
>> + if (state != USB_STATE_CONFIGURED || speed < USB_SPEED_SUPER)
>> + return -EINVAL;
>> +
>> + pdev->u2_allowed = !!set;
>> + break;
>> + case USB_DEVICE_LTM_ENABLE:
>> + return -EINVAL;
>> + case USB_DEVICE_TEST_MODE:
>> + if (state != USB_STATE_CONFIGURED || speed > USB_SPEED_HIGH)
>> + return -EINVAL;
>> +
>> + tmode = le16_to_cpu(ctrl->wIndex);
>> +
>> + if (!set || (tmode & 0xff) != 0)
>> + return -EINVAL;
>> +
>> + tmode = tmode >> 8;
>> +
>> + if (tmode > USB_TEST_FORCE_ENABLE || tmode < USB_TEST_J)
>> + return -EINVAL;
>> +
>> + pdev->test_mode = tmode;
>> +
>> + /*
>> + * Test mode must be set before Status Stage but controller
>> + * will start testing sequence after Status Stage.
>> + */
>> + cdnsp_enter_test_mode(pdev);
>> + break;
>> + default:
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_ep0_handle_feature_intf(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl,
>> + int set)
>> +{
>> + u16 wValue, wIndex;
>> + int ret;
>> +
>> + wValue = le16_to_cpu(ctrl->wValue);
>> + wIndex = le16_to_cpu(ctrl->wIndex);
>> +
>> + switch (wValue) {
>> + case USB_INTRF_FUNC_SUSPEND:
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> + if (ret)
>> + return ret;
>> +
>> + /*
>> + * Remote wakeup is enabled when any function within a device
>> + * is enabled for function remote wakeup.
>> + */
>> + if (wIndex & USB_INTRF_FUNC_SUSPEND_RW)
>> + pdev->may_wakeup++;
>> + else
>> + if (pdev->may_wakeup > 0)
>> + pdev->may_wakeup--;
>> +
>> + return 0;
>> + default:
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_ep0_handle_feature_endpoint(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl,
>> + int set)
>> +{
>> + struct cdnsp_ep *pep;
>> + u32 wValue;
>> +
>> + wValue = le16_to_cpu(ctrl->wValue);
>> + pep = &pdev->eps[cdnsp_w_index_to_ep_index(ctrl->wIndex)];
>> +
>> + switch (wValue) {
>> + case USB_ENDPOINT_HALT:
>> + if (!set && (pep->ep_state & EP_WEDGE)) {
>> + /* Resets Sequence Number */
>> + cdnsp_halt_endpoint(pdev, pep, 0);
>> + cdnsp_halt_endpoint(pdev, pep, 1);
>> + break;
>> + }
>> +
>> + return cdnsp_halt_endpoint(pdev, pep, set);
>> + default:
>> + dev_warn(pdev->dev, "WARN Incorrect wValue %04x\n", wValue);
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_ep0_handle_feature(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl,
>> + int set)
>> +{
>> + switch (ctrl->bRequestType & USB_RECIP_MASK) {
>> + case USB_RECIP_DEVICE:
>> + return cdnsp_ep0_handle_feature_device(pdev, ctrl, set);
>> + case USB_RECIP_INTERFACE:
>> + return cdnsp_ep0_handle_feature_intf(pdev, ctrl, set);
>> + case USB_RECIP_ENDPOINT:
>> + return cdnsp_ep0_handle_feature_endpoint(pdev, ctrl, set);
>> + default:
>> + return -EINVAL;
>> + }
>> +}
>> +
>> +static int cdnsp_ep0_set_sel(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + enum usb_device_state state = pdev->gadget.state;
>> + u16 wLength;
>> +
>> + if (state == USB_STATE_DEFAULT)
>> + return -EINVAL;
>> +
>> + wLength = le16_to_cpu(ctrl->wLength);
>> +
>> + if (wLength != 6) {
>> + dev_err(pdev->dev, "Set SEL should be 6 bytes, got %d\n",
>> + wLength);
>> + return -EINVAL;
>> + }
>> +
>> + /*
>> + * To handle Set SEL we need to receive 6 bytes from Host. So let's
>> + * queue a usb_request for 6 bytes.
>> + */
>> + pdev->ep0_preq.request.length = 6;
>> + pdev->ep0_preq.request.buf = pdev->setup_buf;
>> +
>> + return cdnsp_ep_enqueue(pdev->ep0_preq.pep, &pdev->ep0_preq);
>> +}
>> +
>> +static int cdnsp_ep0_set_isoch_delay(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + if (le16_to_cpu(ctrl->wIndex) || le16_to_cpu(ctrl->wLength))
>> + return -EINVAL;
>> +
>> + pdev->gadget.isoch_delay = le16_to_cpu(ctrl->wValue);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_ep0_std_request(struct cdnsp_device *pdev,
>> + struct usb_ctrlrequest *ctrl)
>> +{
>> + int ret;
>> +
>> + switch (ctrl->bRequest) {
>> + case USB_REQ_GET_STATUS:
>> + ret = cdnsp_ep0_handle_status(pdev, ctrl);
>> + break;
>> + case USB_REQ_CLEAR_FEATURE:
>> + ret = cdnsp_ep0_handle_feature(pdev, ctrl, 0);
>> + break;
>> + case USB_REQ_SET_FEATURE:
>> + ret = cdnsp_ep0_handle_feature(pdev, ctrl, 1);
>> + break;
>> + case USB_REQ_SET_ADDRESS:
>> + ret = cdnsp_ep0_set_address(pdev, ctrl);
>> + break;
>> + case USB_REQ_SET_CONFIGURATION:
>> + ret = cdnsp_ep0_set_config(pdev, ctrl);
>> + break;
>> + case USB_REQ_SET_SEL:
>> + ret = cdnsp_ep0_set_sel(pdev, ctrl);
>> + break;
>> + case USB_REQ_SET_ISOCH_DELAY:
>> + ret = cdnsp_ep0_set_isoch_delay(pdev, ctrl);
>> + break;
>> + case USB_REQ_SET_INTERFACE:
>> + /*
>> + * Add request into pending list to block sending status stage
>> + * by libcomposite.
>> + */
>> + list_add_tail(&pdev->ep0_preq.list,
>> + &pdev->ep0_preq.pep->pending_list);
>> +
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> + if (ret == -EBUSY)
>> + ret = 0;
>> +
>> + list_del(&pdev->ep0_preq.list);
>> + break;
>> + default:
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> + break;
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +void cdnsp_setup_analyze(struct cdnsp_device *pdev)
>> +{
>> + struct usb_ctrlrequest *ctrl = &pdev->setup;
>> + int ret = 0;
>> + __le16 len;
>> +
>> + if (!pdev->gadget_driver)
>> + goto out;
>> +
>> + if (pdev->gadget.state == USB_STATE_NOTATTACHED) {
>> + dev_err(pdev->dev, "ERR: Setup detected in unattached state\n");
>> + ret = -EINVAL;
>> + goto out;
>> + }
>> +
>> + /* Restore the ep0 to Stopped/Running state. */
>> + if (pdev->eps[0].ep_state & EP_HALTED)
>> + cdnsp_halt_endpoint(pdev, &pdev->eps[0], 0);
>> +
>> + /*
>> + * Finishing previous SETUP transfer by removing request from
>> + * list and informing upper layer
>> + */
>> + if (!list_empty(&pdev->eps[0].pending_list)) {
>> + struct cdnsp_request *req;
>> +
>> + req = next_request(&pdev->eps[0].pending_list);
>> + cdnsp_ep_dequeue(&pdev->eps[0], req);
>> + }
>> +
>> + len = le16_to_cpu(ctrl->wLength);
>> + if (!len) {
>> + pdev->three_stage_setup = false;
>> + pdev->ep0_expect_in = false;
>> + } else {
>> + pdev->three_stage_setup = true;
>> + pdev->ep0_expect_in = !!(ctrl->bRequestType & USB_DIR_IN);
>> + }
>> +
>> + if ((ctrl->bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD)
>> + ret = cdnsp_ep0_std_request(pdev, ctrl);
>> + else
>> + ret = cdnsp_ep0_delegate_req(pdev, ctrl);
>> +
>> + if (!len)
>> + pdev->ep0_stage = CDNSP_STATUS_STAGE;
>> +
>> + if (ret == USB_GADGET_DELAYED_STATUS)
>> + return;
>> +out:
>> + if (ret < 0)
>> + cdnsp_ep0_stall(pdev);
>> + else if (pdev->ep0_stage == CDNSP_STATUS_STAGE)
>> + cdnsp_status_stage(pdev);
>> +}
>> diff --git a/drivers/usb/cdnsp/gadget.c b/drivers/usb/cdnsp/gadget.c
>> new file mode 100644
>> index 000000000000..38ad170b2bdd
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/gadget.c
>> @@ -0,0 +1,1946 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Cadence CDNSP DRD Driver.
>> + *
>> + * Copyright (C) 2020 Cadence.
>> + *
>> + * Author: Pawel Laszczak <[email protected]>
>> + *
>> + */
>> +
>> +#include <linux/moduleparam.h>
>> +#include <linux/dma-mapping.h>
>> +#include <linux/module.h>
>> +#include <linux/iopoll.h>
>> +#include <linux/delay.h>
>> +#include <linux/log2.h>
>> +#include <linux/slab.h>
>> +#include <linux/pci.h>
>> +#include <linux/irq.h>
>> +#include <linux/dmi.h>
>> +
>> +#include "../cdns3/core.h"
>> +#include "../cdns3/gadget-export.h"
>> +#include "../cdns3/drd.h"
>> +#include "gadget.h"
>> +
>> +unsigned int cdnsp_port_speed(unsigned int port_status)
>> +{
>> + /*Detect gadget speed based on PORTSC register*/
>> + if (DEV_SUPERSPEEDPLUS(port_status))
>> + return USB_SPEED_SUPER_PLUS;
>> + else if (DEV_SUPERSPEED(port_status))
>> + return USB_SPEED_SUPER;
>> + else if (DEV_HIGHSPEED(port_status))
>> + return USB_SPEED_HIGH;
>> + else if (DEV_FULLSPEED(port_status))
>> + return USB_SPEED_FULL;
>> +
>> + /* If device is detached then speed will be USB_SPEED_UNKNOWN.*/
>> + return USB_SPEED_UNKNOWN;
>> +}
>> +
>> +/*
>> + * Given a port state, this function returns a value that would result in the
>> + * port being in the same state, if the value was written to the port status
>> + * control register.
>> + * Save Read Only (RO) bits and save read/write bits where
>> + * writing a 0 clears the bit and writing a 1 sets the bit (RWS).
>> + * For all other types (RW1S, RW1CS, RW, and RZ), writing a '0' has no effect.
>> + */
>> +u32 cdnsp_port_state_to_neutral(u32 state)
>> +{
>> + /* Save read-only status and port state. */
>> + return (state & CDNSP_PORT_RO) | (state & CDNSP_PORT_RWS);
>> +}
>> +
>> +/**
>> + * Find the offset of the extended capabilities with capability ID id.
>> + * @base: PCI MMIO registers base address.
>> + * @start: Address at which to start looking, (0 or HCC_PARAMS to start at
>> + * beginning of list)
>> + * @id: Extended capability ID to search for.
>> + *
>> + * Returns the offset of the next matching extended capability structure.
>> + * Some capabilities can occur several times,
>> + * e.g., the EXT_CAPS_PROTOCOL, and this provides a way to find them all.
>> + */
>> +int cdnsp_find_next_ext_cap(void __iomem *base, u32 start, int id)
>> +{
>> + u32 offset = start;
>> + u32 next;
>> + u32 val;
>> +
>> + if (!start || start == HCC_PARAMS_OFFSET) {
>> + val = readl(base + HCC_PARAMS_OFFSET);
>> + if (val == ~0)
>> + return 0;
>> +
>> + offset = HCC_EXT_CAPS(val) << 2;
>> + if (!offset)
>> + return 0;
>> + };
>> +
>> + do {
>> + val = readl(base + offset);
>> + if (val == ~0)
>> + return 0;
>> +
>> + if (EXT_CAPS_ID(val) == id && offset != start)
>> + return offset;
>> +
>> + next = EXT_CAPS_NEXT(val);
>> + offset += next << 2;
>> + } while (next);
>> +
>> + return 0;
>> +}
>> +
>> +void cdnsp_set_link_state(struct cdnsp_device *pdev,
>> + __le32 __iomem *port_regs,
>> + u32 link_state)
>> +{
>> + u32 temp;
>> +
>> + temp = readl(port_regs);
>> + temp = cdnsp_port_state_to_neutral(temp);
>> + temp |= PORT_WKCONN_E | PORT_WKDISC_E;
>> + writel(temp, port_regs);
>> +
>> + temp &= ~PORT_PLS_MASK;
>> + temp |= PORT_LINK_STROBE | link_state;
>> +
>> + writel(temp, port_regs);
>> +}
>> +
>> +static void cdnsp_disable_port(struct cdnsp_device *pdev,
>> + __le32 __iomem *port_regs)
>> +{
>> + u32 temp = cdnsp_port_state_to_neutral(readl(port_regs));
>> +
>> + writel(temp | PORT_PED, port_regs);
>> +}
>> +
>> +static void cdnsp_clear_port_change_bit(struct cdnsp_device *pdev,
>> + __le32 __iomem *port_regs)
>> +{
>> + u32 portsc = readl(port_regs);
>> +
>> + writel(cdnsp_port_state_to_neutral(portsc) |
>> + (portsc & PORT_CHANGE_BITS), port_regs);
>> +}
>> +
>> +static void cdnsp_set_chicken_bits_2(struct cdnsp_device *pdev, u32 bit)
>> +{
>> + __le32 __iomem *reg;
>> + void __iomem *base;
>> + u32 offset = 0;
>> +
>> + base = &pdev->cap_regs->hc_capbase;
>> + offset = cdnsp_find_next_ext_cap(base, offset, D_XEC_PRE_REGS_CAP);
>> + reg = base + offset + REG_CHICKEN_BITS_2_OFFSET;
>> +
>> + bit = readl(reg) | bit;
>> + writel(bit, reg);
>> +}
>> +
>> +static void cdnsp_clear_chicken_bits_2(struct cdnsp_device *pdev, u32 bit)
>> +{
>> + __le32 __iomem *reg;
>> + void __iomem *base;
>> + u32 offset = 0;
>> +
>> + base = &pdev->cap_regs->hc_capbase;
>> + offset = cdnsp_find_next_ext_cap(base, offset, D_XEC_PRE_REGS_CAP);
>> + reg = base + offset + REG_CHICKEN_BITS_2_OFFSET;
>> +
>> + bit = readl(reg) & ~bit;
>> + writel(bit, reg);
>> +}
>> +
>> +/*
>> + * Disable interrupts and begin the controller halting process.
>> + */
>> +static void cdnsp_quiesce(struct cdnsp_device *pdev)
>> +{
>> + u32 halted;
>> + u32 mask;
>> + u32 cmd;
>> +
>> + mask = ~(u32)(CDNSP_IRQS);
>> +
>> + halted = readl(&pdev->op_regs->status) & STS_HALT;
>> + if (!halted)
>> + mask &= ~(CMD_R_S | CMD_DEVEN);
>> +
>> + cmd = readl(&pdev->op_regs->command);
>> + cmd &= mask;
>> + writel(cmd, &pdev->op_regs->command);
>> +}
>> +
>> +/*
>> + * Force controller into halt state.
>> + *
>> + * Disable any IRQs and clear the run/stop bit.
>> + * Controller will complete any current and actively pipelined transactions, and
>> + * should halt within 16 ms of the run/stop bit being cleared.
>> + * Read controller Halted bit in the status register to see when the
>> + * controller is finished.
>> + */
>> +int cdnsp_halt(struct cdnsp_device *pdev)
>> +{
>> + int ret;
>> + u32 val;
>> +
>> + cdnsp_quiesce(pdev);
>> +
>> + ret = readl_poll_timeout_atomic(&pdev->op_regs->status, val,
>> + val & STS_HALT, 1,
>> + CDNSP_MAX_HALT_USEC);
>> + if (ret) {
>> + dev_err(pdev->dev, "ERROR: Device halt failed\n");
>> + return ret;
>> + }
>> +
>> + pdev->cdnsp_state |= CDNSP_STATE_HALTED;
>> +
>> + return 0;
>> +}
>> +
>> +/*
>> + * device controller died, register read returns 0xffffffff, or command never
>> + * ends.
>> + */
>> +void cdnsp_died(struct cdnsp_device *pdev)
>> +{
>> + dev_err(pdev->dev, "ERROR: CDNSP controller not responding\n");
>> + pdev->cdnsp_state |= CDNSP_STATE_DYING;
>> + cdnsp_halt(pdev);
>> +}
>> +
>> +/*
>> + * Set the run bit and wait for the device to be running.
>> + */
>> +static int cdnsp_start(struct cdnsp_device *pdev)
>> +{
>> + u32 temp;
>> + int ret;
>> +
>> + temp = readl(&pdev->op_regs->command);
>> + temp |= (CMD_R_S | CMD_DEVEN);
>> + writel(temp, &pdev->op_regs->command);
>> +
>> + pdev->cdnsp_state = 0;
>> +
>> + /*
>> + * Wait for the STS_HALT Status bit to be 0 to indicate the device is
>> + * running.
>> + */
>> + ret = readl_poll_timeout_atomic(&pdev->op_regs->status, temp,
>> + !(temp & STS_HALT), 1,
>> + CDNSP_MAX_HALT_USEC);
>> + if (ret) {
>> + pdev->cdnsp_state = CDNSP_STATE_DYING;
>> + dev_err(pdev->dev, "ERROR: Controller run failed\n");
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * Reset a halted controller.
>> + *
>> + * This resets pipelines, timers, counters, state machines, etc.
>> + * Transactions will be terminated immediately, and operational registers
>> + * will be set to their defaults.
>> + */
>> +int cdnsp_reset(struct cdnsp_device *pdev)
>> +{
>> + u32 command;
>> + u32 temp;
>> + int ret;
>> +
>> + temp = readl(&pdev->op_regs->status);
>> +
>> + if (temp == ~(u32)0) {
>> + dev_err(pdev->dev, "Device not accessible, reset failed.\n");
>> + return -ENODEV;
>> + }
>> +
>> + if ((temp & STS_HALT) == 0) {
>> + dev_err(pdev->dev, "Controller not halted, aborting reset.\n");
>> + return -EINVAL;
>> + }
>> +
>> + command = readl(&pdev->op_regs->command);
>> + command |= CMD_RESET;
>> + writel(command, &pdev->op_regs->command);
>> +
>> + ret = readl_poll_timeout_atomic(&pdev->op_regs->command, temp,
>> + !(temp & CMD_RESET), 1,
>> + 10 * 1000);
>> + if (ret) {
>> + dev_err(pdev->dev, "ERROR: Controller reset failed\n");
>> + return ret;
>> + }
>> +
>> + /*
>> + * CDNSP cannot write any doorbells or operational registers other
>> + * than status until the "Controller Not Ready" flag is cleared.
>> + */
>> + ret = readl_poll_timeout_atomic(&pdev->op_regs->status, temp,
>> + !(temp & STS_CNR), 1,
>> + 10 * 1000);
>> +
>> + if (ret) {
>> + dev_err(pdev->dev, "ERROR: Controller not ready to work\n");
>> + return ret;
>> + }
>> +
>> + dev_info(pdev->dev, "Controller ready to work");
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * cdnsp_get_endpoint_index - Find the index for an endpoint given its
>> + * descriptor.Use the return value to right shift 1 for the bitmask.
>> + *
>> + * Index = (epnum * 2) + direction - 1,
>> + * where direction = 0 for OUT, 1 for IN.
>> + * For control endpoints, the IN index is used (OUT index is unused), so
>> + * index = (epnum * 2) + direction - 1 = (epnum * 2) + 1 - 1 = (epnum * 2)
>> + */
>> +static unsigned int
>> + cdnsp_get_endpoint_index(const struct usb_endpoint_descriptor *desc)
>> +{
>> + unsigned int index = (unsigned int)usb_endpoint_num(desc);
>> +
>> + if (usb_endpoint_xfer_control(desc))
>> + return index * 2;
>> +
>> + return (index * 2) + (usb_endpoint_dir_in(desc) ? 1 : 0) - 1;
>> +}
>> +
>> +/*
>> + * Find the flag for this endpoint (for use in the control context). Use the
>> + * endpoint index to create a bitmask. The slot context is bit 0, endpoint 0 is
>> + * bit 1, etc.
>> + */
>> +static unsigned int
>> + cdnsp_get_endpoint_flag(const struct usb_endpoint_descriptor *desc)
>> +{
>> + return 1 << (cdnsp_get_endpoint_index(desc) + 1);
>> +}
>> +
>> +int cdnsp_ep_enqueue(struct cdnsp_ep *pep, struct cdnsp_request *preq)
>> +{
>> + struct cdnsp_device *pdev = pep->pdev;
>> + struct usb_request *request;
>> + int ret;
>> +
>> + if (preq->epnum == 0 && !list_empty(&pep->pending_list))
>> + return -EBUSY;
>> +
>> + request = &preq->request;
>> + request->actual = 0;
>> + request->status = -EINPROGRESS;
>> + preq->direction = pep->direction;
>> + preq->epnum = pep->number;
>> + preq->td.drbl = 0;
>> +
>> + ret = usb_gadget_map_request_by_dev(pdev->dev, request, pep->direction);
>> + if (ret)
>> + return ret;
>> +
>> + list_add_tail(&preq->list, &pep->pending_list);
>> +
>> + switch (usb_endpoint_type(pep->endpoint.desc)) {
>> + case USB_ENDPOINT_XFER_CONTROL:
>> + ret = cdnsp_queue_ctrl_tx(pdev, preq);
>> + break;
>> + case USB_ENDPOINT_XFER_BULK:
>> + case USB_ENDPOINT_XFER_INT:
>> + ret = cdnsp_queue_bulk_tx(pdev, preq);
>> + break;
>> + case USB_ENDPOINT_XFER_ISOC:
>> + ret = cdnsp_queue_isoc_tx_prepare(pdev, preq);
>> + }
>> +
>> + if (ret)
>> + goto unmap;
>> +
>> + return 0;
>> +
>> +unmap:
>> + usb_gadget_unmap_request_by_dev(pdev->dev, &preq->request,
>> + pep->direction);
>> + list_del(&preq->list);
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * Remove the request's TD from the endpoint ring. This may cause the
>> + * controller to stop USB transfers, potentially stopping in the middle of a
>> + * TRB buffer. The controller should pick up where it left off in the TD,
>> + * unless a Set Transfer Ring Dequeue Pointer is issued.
>> + *
>> + * The TRBs that make up the buffers for the canceled request will be "removed"
>> + * from the ring. Since the ring is a contiguous structure, they can't be
>> + * physically removed. Instead, there are two options:
>> + *
>> + * 1) If the controller is in the middle of processing the request to be
>> + * canceled, we simply move the ring's dequeue pointer past those TRBs
>> + * using the Set Transfer Ring Dequeue Pointer command. This will be
>> + * the common case, when drivers timeout on the last submitted request
>> + * and attempt to cancel.
>> + *
>> + * 2) If the controller is in the middle of a different TD, we turn the TRBs
>> + * into a series of 1-TRB transfer no-op TDs. No-ops shouldn't be chained.
>> + * The controller will need to invalidate the any TRBs it has cached after
>> + * the stop endpoint command.
>> + *
>> + * 3) The TD may have completed by the time the Stop Endpoint Command
>> + * completes, so software needs to handle that case too.
>> + *
>> + */
>> +int cdnsp_ep_dequeue(struct cdnsp_ep *pep, struct cdnsp_request *preq)
>> +{
>> + struct cdnsp_device *pdev = pep->pdev;
>> + int ret;
>> +
>> + if (GET_EP_CTX_STATE(pep->out_ctx) == EP_STATE_RUNNING) {
>> + ret = cdnsp_cmd_stop_ep(pdev, pep);
>> + if (ret)
>> + return ret;
>> + }
>> +
>> + return cdnsp_remove_request(pdev, preq, pep);
>> +}
>> +
>> +static void cdnsp_zero_in_ctx(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_input_control_ctx *ctrl_ctx;
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + struct cdnsp_ep_ctx *ep_ctx;
>> + int i;
>> +
>> + ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx);
>> +
>> + /*
>> + * When a device's add flag and drop flag are zero, any subsequent
>> + * configure endpoint command will leave that endpoint's state
>> + * untouched. Make sure we don't leave any old state in the input
>> + * endpoint contexts.
>> + */
>> + ctrl_ctx->drop_flags = 0;
>> + ctrl_ctx->add_flags = 0;
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx);
>> + slot_ctx->dev_info &= cpu_to_le32(~LAST_CTX_MASK);
>> +
>> + /* Endpoint 0 is always valid */
>> + slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(1));
>> + for (i = 1; i < 31; ++i) {
>> + ep_ctx = cdnsp_get_ep_ctx(&pdev->in_ctx, i);
>> + ep_ctx->ep_info = 0;
>> + ep_ctx->ep_info2 = 0;
>> + ep_ctx->deq = 0;
>> + ep_ctx->tx_info = 0;
>> + }
>> +}
>> +
>> +/* Issue a configure endpoint command and wait for it to finish. */
>> +static int cdnsp_configure_endpoint(struct cdnsp_device *pdev)
>> +{
>> + int ret;
>> +
>> + cdnsp_queue_configure_endpoint(pdev, pdev->cmd.in_ctx->dma);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> + if (ret) {
>> + dev_err(pdev->dev,
>> + "ERR: unexpected command completion code 0x%x.\n", ret);
>> + return -EINVAL;
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +static void cdnsp_invalidate_ep_events(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep)
>> +{
>> + struct cdnsp_segment *segment;
>> + union cdnsp_trb *event;
>> + u32 cycle_state;
>> + __le32 data;
>> +
>> + event = pdev->event_ring->dequeue;
>> + segment = pdev->event_ring->deq_seg;
>> + cycle_state = pdev->event_ring->cycle_state;
>> +
>> + while (1) {
>> + data = le32_to_cpu(event->trans_event.flags);
>> +
>> + /* Check the owner of the TRB. */
>> + if ((data & TRB_CYCLE) != cycle_state)
>> + break;
>> +
>> + if (TRB_FIELD_TO_TYPE(data) == TRB_TRANSFER &&
>> + TRB_TO_EP_ID(data) == (pep->idx + 1)) {
>> + data |= TRB_EVENT_INVALIDATE;
>> + event->trans_event.flags = cpu_to_le32(data);
>> + }
>> +
>> + if (cdnsp_last_trb_on_seg(segment, event)) {
>> + cycle_state ^= 1;
>> + segment = pdev->event_ring->deq_seg->next;
>> + event = segment->trbs;
>> + } else {
>> + event++;
>> + }
>> + }
>> +}
>> +
>> +int cdnsp_wait_for_cmd_compl(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_segment *event_deq_seg;
>> + dma_addr_t cmd_deq_dma;
>> + union cdnsp_trb *cmd_trb;
>> + union cdnsp_trb *event;
>> + u32 cycle_state;
>> + __le32 flags;
>> + int ret, val;
>> + u64 cmd_dma;
>> +
>> + cmd_trb = pdev->cmd.command_trb;
>> + pdev->cmd.status = 0;
>> +
>> + ret = readl_poll_timeout_atomic(&pdev->op_regs->cmd_ring, val,
>> + !CMD_RING_BUSY(val), 1,
>> + CDNSP_CMD_TIMEOUT);
>> + if (ret) {
>> + dev_err(pdev->dev, "ERR: Timeout while waiting for command\n");
>> + pdev->cdnsp_state = CDNSP_STATE_DYING;
>> + return -ETIMEDOUT;
>> + }
>> +
>> + event = pdev->event_ring->dequeue;
>> + event_deq_seg = pdev->event_ring->deq_seg;
>> + cycle_state = pdev->event_ring->cycle_state;
>> +
>> + cmd_deq_dma = cdnsp_trb_virt_to_dma(pdev->cmd_ring->deq_seg, cmd_trb);
>> + if (!cmd_deq_dma)
>> + return -EINVAL;
>> +
>> + while (1) {
>> + flags = le32_to_cpu(event->event_cmd.flags);
>> +
>> + /* Check the owner of the TRB. */
>> + if ((flags & TRB_CYCLE) != cycle_state)
>> + return -EINVAL;
>> +
>> + cmd_dma = le64_to_cpu(event->event_cmd.cmd_trb);
>> +
>> + /*
>> + * Check whether the completion event is for last queued
>> + * command.
>> + */
>> + if (TRB_FIELD_TO_TYPE(flags) != TRB_COMPLETION ||
>> + cmd_dma != (u64)cmd_deq_dma) {
>> + if (!cdnsp_last_trb_on_seg(event_deq_seg, event)) {
>> + event++;
>> + continue;
>> + }
>> +
>> + if (cdnsp_last_trb_on_ring(pdev->event_ring,
>> + event_deq_seg, event))
>> + cycle_state ^= 1;
>> +
>> + event_deq_seg = event_deq_seg->next;
>> + event = event_deq_seg->trbs;
>> + continue;
>> + }
>> +
>> + pdev->cmd.status = GET_COMP_CODE(le32_to_cpu(event->event_cmd.status));
>> + if (pdev->cmd.status == COMP_SUCCESS)
>> + return 0;
>> +
>> + return -pdev->cmd.status;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +int cdnsp_halt_endpoint(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep,
>> + int value)
>> +{
>> + int ret;
>> +
>> + if (value) {
>> + ret = cdnsp_cmd_stop_ep(pdev, pep);
>> + if (ret)
>> + return ret;
>> +
>> + if (GET_EP_CTX_STATE(pep->out_ctx) == EP_STATE_STOPPED) {
>> + cdnsp_queue_halt_endpoint(pdev, pep->idx);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> + }
>> +
>> + pep->ep_state |= EP_HALTED;
>> + } else {
>> + /*
>> + * In device mode driver can call reset endpoint command
>> + * from any endpoint state.
>> + */
>> + cdnsp_queue_reset_ep(pdev, pep->idx);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> + if (ret)
>> + return ret;
>> +
>> + pep->ep_state &= ~EP_HALTED;
>> +
>> + if (pep->idx != 0 && !(pep->ep_state & EP_WEDGE))
>> + cdnsp_ring_doorbell_for_active_rings(pdev, pep);
>> +
>> + pep->ep_state &= ~EP_WEDGE;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_update_eps_configuration(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep)
>> +{
>> + struct cdnsp_input_control_ctx *ctrl_ctx;
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + int ret = 0;
>> + u32 ep_sts;
>> + int i;
>> +
>> + ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx);
>> +
>> + /* Don't issue the command if there's no endpoints to update. */
>> + if (ctrl_ctx->add_flags == 0 && ctrl_ctx->drop_flags == 0)
>> + return 0;
>> +
>> + ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG);
>> + ctrl_ctx->add_flags &= cpu_to_le32(~EP0_FLAG);
>> + ctrl_ctx->drop_flags &= cpu_to_le32(~(SLOT_FLAG | EP0_FLAG));
>> +
>> + /* Fix up Context Entries field. Minimum value is EP0 == BIT(1). */
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx);
>> + for (i = 31; i >= 1; i--) {
>> + __le32 le32 = cpu_to_le32(BIT(i));
>> +
>> + if ((pdev->eps[i - 1].ring && !(ctrl_ctx->drop_flags & le32)) ||
>> + (ctrl_ctx->add_flags & le32) || i == 1) {
>> + slot_ctx->dev_info &= cpu_to_le32(~LAST_CTX_MASK);
>> + slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(i));
>> + break;
>> + }
>> + }
>> +
>> + ep_sts = GET_EP_CTX_STATE(pep->out_ctx);
>> +
>> + if ((ctrl_ctx->add_flags != cpu_to_le32(SLOT_FLAG) &&
>> + ep_sts == EP_STATE_DISABLED) ||
>> + (ep_sts != EP_STATE_DISABLED && ctrl_ctx->drop_flags))
>> + ret = cdnsp_configure_endpoint(pdev);
>> +
>> + cdnsp_zero_in_ctx(pdev);
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * This submits a Reset Device Command, which will set the device state to 0,
>> + * set the device address to 0, and disable all the endpoints except the default
>> + * control endpoint. The USB core should come back and call
>> + * cdnsp_setup_device(), and then re-set up the configuration.
>> + */
>> +int cdnsp_reset_device(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + int slot_state;
>> + int ret, i;
>> +
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx);
>> + slot_ctx->dev_info = 0;
>> + pdev->device_address = 0;
>> +
>> + /* If device is not setup, there is no point in resetting it. */
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx);
>> + slot_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state));
>> +
>> + if (slot_state <= SLOT_STATE_DEFAULT &&
>> + pdev->eps[0].ep_state & EP_HALTED) {
>> + cdnsp_halt_endpoint(pdev, &pdev->eps[0], 0);
>> + }
>> +
>> + /*
>> + * During Reset Device command controller shall transition the
>> + * endpoint ep0 to the Running State.
>> + */
>> + pdev->eps[0].ep_state &= ~(EP_STOPPED | EP_HALTED);
>> + pdev->eps[0].ep_state |= EP_ENABLED;
>> +
>> + if (slot_state <= SLOT_STATE_DEFAULT)
>> + return 0;
>> +
>> + cdnsp_queue_reset_device(pdev);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> +
>> + /*
>> + * After Reset Device command all not default endpoints
>> + * are in Disabled state.
>> + */
>> + for (i = 1; i < 31; ++i)
>> + pdev->eps[i].ep_state |= EP_STOPPED;
>> +
>> + if (ret)
>> + dev_err(pdev->dev, "Reset device failed with error code %d",
>> + ret);
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * Sets the MaxPStreams field and the Linear Stream Array field.
>> + * Sets the dequeue pointer to the stream context array.
>> + */
>> +static void cdnsp_setup_streams_ep_input_ctx(struct cdnsp_device *pdev,
>> + struct cdnsp_ep_ctx *ep_ctx,
>> + struct cdnsp_stream_info *stream_info)
>> +{
>> + u32 max_primary_streams;
>> +
>> + /* MaxPStreams is the number of stream context array entries, not the
>> + * number we're actually using. Must be in 2^(MaxPstreams + 1) format.
>> + * fls(0) = 0, fls(0x1) = 1, fls(0x10) = 2, fls(0x100) = 3, etc.
>> + */
>> + max_primary_streams = fls(stream_info->num_stream_ctxs) - 2;
>> + ep_ctx->ep_info &= cpu_to_le32(~EP_MAXPSTREAMS_MASK);
>> + ep_ctx->ep_info |= cpu_to_le32(EP_MAXPSTREAMS(max_primary_streams)
>> + | EP_HAS_LSA);
>> + ep_ctx->deq = cpu_to_le64(stream_info->ctx_array_dma);
>> +}
>> +
>> +/*
>> + * The drivers use this function to prepare a bulk endpoints to use streams.
>> + *
>> + * Don't allow the call to succeed if endpoint only supports one stream
>> + * (which means it doesn't support streams at all).
>> + */
>> +int cdnsp_alloc_streams(struct cdnsp_device *pdev, struct cdnsp_ep *pep)
>> +{
>> + unsigned int num_streams = usb_ss_max_streams(pep->endpoint.comp_desc);
>> + unsigned int num_stream_ctxs;
>> + int ret;
>> +
>> + if (num_streams == 0)
>> + return 0;
>> +
>> + if (num_streams > STREAM_NUM_STREAMS)
>> + return -EINVAL;
>> +
>> + /*
>> + * Add two to the number of streams requested to account for
>> + * stream 0 that is reserved for controller usage and one additional
>> + * for TASK SET FULL response.
>> + */
>> + num_streams += 2;
>> +
>> + /* The stream context array size must be a power of two */
>> + num_stream_ctxs = roundup_pow_of_two(num_streams);
>> +
>> + ret = cdnsp_alloc_stream_info(pdev, pep, num_stream_ctxs, num_streams);
>> + if (ret)
>> + return ret;
>> +
>> + cdnsp_setup_streams_ep_input_ctx(pdev, pep->in_ctx, &pep->stream_info);
>> +
>> + pep->ep_state |= EP_HAS_STREAMS;
>> + pep->stream_info.td_count = 0;
>> + pep->stream_info.first_prime_det = 0;
>> +
>> + /* Subtract 1 for stream 0, which drivers can't use. */
>> + return num_streams - 1;
>> +}
>> +
>> +int cdnsp_disable_slot(struct cdnsp_device *pdev)
>> +{
>> + int ret;
>> +
>> + cdnsp_queue_slot_control(pdev, TRB_DISABLE_SLOT);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> +
>> + pdev->slot_id = 0;
>> + pdev->active_port = NULL;
>> +
>> + memset(pdev->in_ctx.bytes, 0, CDNSP_CTX_SIZE);
>> + memset(pdev->out_ctx.bytes, 0, CDNSP_CTX_SIZE);
>> +
>> + return ret;
>> +}
>> +
>> +int cdnsp_enable_slot(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + int slot_state;
>> + int ret;
>> +
>> + /* If device is not setup, there is no point in resetting it */
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx);
>> + slot_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state));
>> +
>> + if (slot_state != SLOT_STATE_DISABLED)
>> + return 0;
>> +
>> + cdnsp_queue_slot_control(pdev, TRB_ENABLE_SLOT);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> + if (ret)
>> + return ret;
>> +
>> + pdev->slot_id = 1;
>> +
>> + return 0;
>> +}
>> +
>> +/*
>> + * Issue an Address Device command with BSR=0 if setup is SETUP_CONTEXT_ONLY
>> + * or with BSR = 1 if set_address is SETUP_CONTEXT_ADDRESS.
>> + */
>> +int cdnsp_setup_device(struct cdnsp_device *pdev, enum cdnsp_setup_dev setup)
>> +{
>> + struct cdnsp_input_control_ctx *ctrl_ctx;
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + int dev_state = 0;
>> + int ret;
>> +
>> + if (!pdev->slot_id)
>> + return -EINVAL;
>> +
>> + if (!pdev->active_port->port_num)
>> + return -EINVAL;
>> +
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx);
>> + dev_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state));
>> +
>> + if (setup == SETUP_CONTEXT_ONLY && dev_state == SLOT_STATE_DEFAULT)
>> + return 0;
>> +
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx);
>> + ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx);
>> +
>> + if (!slot_ctx->dev_info || dev_state == SLOT_STATE_DEFAULT) {
>> + ret = cdnsp_setup_addressable_priv_dev(pdev);
>> + if (ret)
>> + return ret;
>> + }
>> +
>> + cdnsp_copy_ep0_dequeue_into_input_ctx(pdev);
>> +
>> + ctrl_ctx->add_flags = cpu_to_le32(SLOT_FLAG | EP0_FLAG);
>> + ctrl_ctx->drop_flags = 0;
>> +
>> + cdnsp_queue_address_device(pdev, pdev->in_ctx.dma, setup);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> +
>> + /* Zero the input context control for later use. */
>> + ctrl_ctx->add_flags = 0;
>> + ctrl_ctx->drop_flags = 0;
>> +
>> + return ret;
>> +}
>> +
>> +void cdnsp_set_usb2_hardware_lpm(struct cdnsp_device *pdev,
>> + struct usb_request *req,
>> + int enable)
>> +{
>> + if (pdev->active_port != &pdev->usb2_port || !pdev->gadget.lpm_capable)
>> + return;
>> +
>> + if (enable)
>> + writel(PORT_BESL(CDNSP_DEFAULT_BESL) | PORT_L1S_NYET | PORT_HLE,
>> + &pdev->active_port->regs->portpmsc);
>> + else
>> + writel(PORT_L1S_NYET, &pdev->active_port->regs->portpmsc);
>> +}
>> +
>> +static int cdnsp_get_frame(struct cdnsp_device *pdev)
>> +{
>> + return readl(&pdev->run_regs->microframe_index) >> 3;
>> +}
>> +
>> +static int cdnsp_gadget_ep_enable(struct usb_ep *ep,
>> + const struct usb_endpoint_descriptor *desc)
>> +{
>> + struct cdnsp_input_control_ctx *ctrl_ctx;
>> + struct cdnsp_device *pdev;
>> + struct cdnsp_ep *pep;
>> + unsigned long flags;
>> + u32 added_ctxs;
>> + int ret;
>> +
>> + if (!ep || !desc || desc->bDescriptorType != USB_DT_ENDPOINT ||
>> + !desc->wMaxPacketSize)
>> + return -EINVAL;
>> +
>> + pep = to_cdnsp_ep(ep);
>> + pdev = pep->pdev;
>> +
>> + if (dev_WARN_ONCE(pdev->dev, pep->ep_state & EP_ENABLED,
>> + "%s is already enabled\n", pep->name))
>> + return 0;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> +
>> + added_ctxs = cdnsp_get_endpoint_flag(desc);
>> + if (added_ctxs == SLOT_FLAG || added_ctxs == EP0_FLAG) {
>> + dev_err(pdev->dev, "ERROR: Bad endpoint number\n");
>> + ret = -EINVAL;
>> + goto unlock;
>> + }
>> +
>> + pep->interval = desc->bInterval ? BIT(desc->bInterval - 1) : 0;
>> +
>> + if (pdev->gadget.speed == USB_SPEED_FULL) {
>> + if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_INT)
>> + pep->interval = desc->bInterval << 3;
>> + if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_ISOC)
>> + pep->interval = BIT(desc->bInterval - 1) << 3;
>> + }
>> +
>> + if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_ISOC) {
>> + if (pep->interval > BIT(12)) {
>> + dev_err(pdev->dev, "bInterval %d not supported\n",
>> + desc->bInterval);
>> + ret = -EINVAL;
>> + goto unlock;
>> + }
>> + cdnsp_set_chicken_bits_2(pdev, CHICKEN_XDMA_2_TP_CACHE_DIS);
>> + }
>> +
>> + ret = cdnsp_endpoint_init(pdev, pep, GFP_ATOMIC);
>> + if (ret)
>> + goto unlock;
>> +
>> + ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx);
>> + ctrl_ctx->add_flags = cpu_to_le32(added_ctxs);
>> + ctrl_ctx->drop_flags = 0;
>> +
>> + ret = cdnsp_update_eps_configuration(pdev, pep);
>> + if (ret) {
>> + cdnsp_free_endpoint_rings(pdev, pep);
>> + goto unlock;
>> + }
>> +
>> + pep->ep_state |= EP_ENABLED;
>> + pep->ep_state &= ~EP_STOPPED;
>> +
>> +unlock:
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +static int cdnsp_gadget_ep_disable(struct usb_ep *ep)
>> +{
>> + struct cdnsp_input_control_ctx *ctrl_ctx;
>> + struct cdnsp_request *preq;
>> + struct cdnsp_device *pdev;
>> + struct cdnsp_ep *pep;
>> + unsigned long flags;
>> + u32 drop_flag;
>> + int ret = 0;
>> +
>> + if (!ep)
>> + return -EINVAL;
>> +
>> + pep = to_cdnsp_ep(ep);
>> + pdev = pep->pdev;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> +
>> + if (!(pep->ep_state & EP_ENABLED)) {
>> + dev_err(pdev->dev, "%s is already disabled\n", pep->name);
>> + ret = -EINVAL;
>> + goto finish;
>> + }
>> +
>> + cdnsp_cmd_stop_ep(pdev, pep);
>> + pep->ep_state |= EP_DIS_IN_RROGRESS;
>> + cdnsp_cmd_flush_ep(pdev, pep);
>> +
>> + /* Remove all queued USB requests. */
>> + while (!list_empty(&pep->pending_list)) {
>> + preq = next_request(&pep->pending_list);
>> + cdnsp_ep_dequeue(pep, preq);
>> + }
>> +
>> + cdnsp_invalidate_ep_events(pdev, pep);
>> +
>> + pep->ep_state &= ~EP_DIS_IN_RROGRESS;
>> + drop_flag = cdnsp_get_endpoint_flag(pep->endpoint.desc);
>> + ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx);
>> + ctrl_ctx->drop_flags = cpu_to_le32(drop_flag);
>> + ctrl_ctx->add_flags = 0;
>> +
>> + cdnsp_endpoint_zero(pdev, pep);
>> +
>> + ret = cdnsp_update_eps_configuration(pdev, pep);
>> + cdnsp_free_endpoint_rings(pdev, pep);
>> +
>> + pep->ep_state &= ~EP_ENABLED;
>> + pep->ep_state |= EP_STOPPED;
>> +
>> +finish:
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +static struct usb_request *cdnsp_gadget_ep_alloc_request(struct usb_ep *ep,
>> + gfp_t gfp_flags)
>> +{
>> + struct cdnsp_ep *pep = to_cdnsp_ep(ep);
>> + struct cdnsp_request *preq;
>> +
>> + preq = kzalloc(sizeof(*preq), gfp_flags);
>> + if (!preq)
>> + return NULL;
>> +
>> + preq->epnum = pep->number;
>> + preq->pep = pep;
>> +
>> + return &preq->request;
>> +}
>> +
>> +static void cdnsp_gadget_ep_free_request(struct usb_ep *ep,
>> + struct usb_request *request)
>> +{
>> + struct cdnsp_request *preq = to_cdnsp_request(request);
>> +
>> + kfree(preq);
>> +}
>> +
>> +static int cdnsp_gadget_ep_queue(struct usb_ep *ep,
>> + struct usb_request *request,
>> + gfp_t gfp_flags)
>> +{
>> + struct cdnsp_request *preq;
>> + struct cdnsp_device *pdev;
>> + struct cdnsp_ep *pep;
>> + unsigned long flags;
>> + int ret;
>> +
>> + if (!request || !ep)
>> + return -EINVAL;
>> +
>> + pep = to_cdnsp_ep(ep);
>> + pdev = pep->pdev;
>> +
>> + if (!(pep->ep_state & EP_ENABLED)) {
>> + dev_err(pdev->dev, "%s: can't queue to disabled endpoint\n",
>> + pep->name);
>> + return -EINVAL;
>> + }
>> +
>> + preq = to_cdnsp_request(request);
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + ret = cdnsp_ep_enqueue(pep, preq);
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +static int cdnsp_gadget_ep_dequeue(struct usb_ep *ep,
>> + struct usb_request *request)
>> +{
>> + struct cdnsp_ep *pep = to_cdnsp_ep(ep);
>> + struct cdnsp_device *pdev = pep->pdev;
>> + unsigned long flags;
>> + int ret;
>> +
>> + if (!pep->endpoint.desc) {
>> + dev_err(pdev->dev,
>> + "%s: can't dequeue to disabled endpoint\n",
>> + pep->name);
>> + return -ESHUTDOWN;
>> + }
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + ret = cdnsp_ep_dequeue(pep, to_cdnsp_request(request));
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +static int cdnsp_gadget_ep_set_halt(struct usb_ep *ep, int value)
>> +{
>> + struct cdnsp_ep *pep = to_cdnsp_ep(ep);
>> + struct cdnsp_device *pdev = pep->pdev;
>> + struct cdnsp_request *preq;
>> + unsigned long flags = 0;
>> + int ret;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> +
>> + preq = next_request(&pep->pending_list);
>> + if (value) {
>> + if (preq) {
>> + ret = -EAGAIN;
>> + goto done;
>> + }
>> + }
>> +
>> + ret = cdnsp_halt_endpoint(pdev, pep, value);
>> +
>> +done:
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> + return ret;
>> +}
>> +
>> +static int cdnsp_gadget_ep_set_wedge(struct usb_ep *ep)
>> +{
>> + struct cdnsp_ep *pep = to_cdnsp_ep(ep);
>> + struct cdnsp_device *pdev = pep->pdev;
>> + unsigned long flags = 0;
>> + int ret;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + pep->ep_state |= EP_WEDGE;
>> + ret = cdnsp_halt_endpoint(pdev, pep, 1);
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +static const struct usb_ep_ops cdnsp_gadget_ep0_ops = {
>> + .enable = cdnsp_gadget_ep_enable,
>> + .disable = cdnsp_gadget_ep_disable,
>> + .alloc_request = cdnsp_gadget_ep_alloc_request,
>> + .free_request = cdnsp_gadget_ep_free_request,
>> + .queue = cdnsp_gadget_ep_queue,
>> + .dequeue = cdnsp_gadget_ep_dequeue,
>> + .set_halt = cdnsp_gadget_ep_set_halt,
>> + .set_wedge = cdnsp_gadget_ep_set_wedge,
>> +};
>> +
>> +static const struct usb_ep_ops cdnsp_gadget_ep_ops = {
>> + .enable = cdnsp_gadget_ep_enable,
>> + .disable = cdnsp_gadget_ep_disable,
>> + .alloc_request = cdnsp_gadget_ep_alloc_request,
>> + .free_request = cdnsp_gadget_ep_free_request,
>> + .queue = cdnsp_gadget_ep_queue,
>> + .dequeue = cdnsp_gadget_ep_dequeue,
>> + .set_halt = cdnsp_gadget_ep_set_halt,
>> + .set_wedge = cdnsp_gadget_ep_set_wedge,
>> +};
>> +
>> +void cdnsp_gadget_giveback(struct cdnsp_ep *pep,
>> + struct cdnsp_request *preq,
>> + int status)
>> +{
>> + struct cdnsp_device *pdev = pep->pdev;
>> +
>> + list_del(&preq->list);
>> +
>> + if (preq->request.status == -EINPROGRESS)
>> + preq->request.status = status;
>> +
>> + usb_gadget_unmap_request_by_dev(pdev->dev, &preq->request,
>> + preq->direction);
>> +
>> + if (preq != &pdev->ep0_preq) {
>> + spin_unlock(&pdev->lock);
>> + usb_gadget_giveback_request(&pep->endpoint, &preq->request);
>> + spin_lock(&pdev->lock);
>> + }
>> +}
>> +
>> +static struct usb_endpoint_descriptor cdnsp_gadget_ep0_desc = {
>> + .bLength = USB_DT_ENDPOINT_SIZE,
>> + .bDescriptorType = USB_DT_ENDPOINT,
>> + .bmAttributes = USB_ENDPOINT_XFER_CONTROL,
>> +};
>> +
>> +static int cdnsp_run(struct cdnsp_device *pdev,
>> + enum usb_device_speed speed)
>> +{
>> + u32 fs_speed = 0;
>> + u64 temp_64;
>> + u32 temp;
>> + int ret;
>> +
>> + temp_64 = cdnsp_read_64(pdev, &pdev->ir_set->erst_dequeue);
>> + temp_64 &= ~ERST_PTR_MASK;
>> + temp = readl(&pdev->ir_set->irq_control);
>> + temp &= ~IMOD_INTERVAL_MASK;
>> + temp |= ((IMOD_DEFAULT_INTERVAL / 250) & IMOD_INTERVAL_MASK);
>> + writel(temp, &pdev->ir_set->irq_control);
>> +
>> + temp = readl(&pdev->port3x_regs->mode_addr);
>> +
>> + switch (speed) {
>> + case USB_SPEED_SUPER_PLUS:
>> + temp |= CFG_3XPORT_SSP_SUPPORT;
>> + break;
>> + case USB_SPEED_SUPER:
>> + temp &= ~CFG_3XPORT_SSP_SUPPORT;
>> + break;
>> + case USB_SPEED_HIGH:
>> + break;
>> + case USB_SPEED_FULL:
>> + fs_speed = PORT_REG6_FORCE_FS;
>> + break;
>> + default:
>> + dev_err(pdev->dev, "invalid maximum_speed parameter %d\n",
>> + speed);
>> + fallthrough;
>> + case USB_SPEED_UNKNOWN:
>> + /* Default to superspeed. */
>> + speed = USB_SPEED_SUPER;
>> + break;
>> + }
>> +
>> + if (speed >= USB_SPEED_SUPER) {
>> + writel(temp, &pdev->port3x_regs->mode_addr);
>> + cdnsp_set_link_state(pdev, &pdev->usb3_port.regs->portsc,
>> + XDEV_RXDETECT);
>> + } else {
>> + cdnsp_disable_port(pdev, &pdev->usb3_port.regs->portsc);
>> + }
>> +
>> + cdnsp_set_link_state(pdev, &pdev->usb2_port.regs->portsc,
>> + XDEV_RXDETECT);
>> +
>> + cdnsp_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(512);
>> +
>> + writel(PORT_REG6_L1_L0_HW_EN | fs_speed, &pdev->port20_regs->port_reg6);
>> +
>> + ret = cdnsp_start(pdev);
>> + if (ret) {
>> + ret = -ENODEV;
>> + goto err;
>> + }
>> +
>> + temp = readl(&pdev->op_regs->command);
>> + temp |= (CMD_INTE);
>> + writel(temp, &pdev->op_regs->command);
>> +
>> + temp = readl(&pdev->ir_set->irq_pending);
>> + writel(IMAN_IE_SET(temp), &pdev->ir_set->irq_pending);
>> +
>> + return 0;
>> +err:
>> + cdnsp_halt(pdev);
>> + return ret;
>> +}
>> +
>> +static int cdnsp_gadget_udc_start(struct usb_gadget *g,
>> + struct usb_gadget_driver *driver)
>> +{
>> + enum usb_device_speed max_speed = driver->max_speed;
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(g);
>> + unsigned long flags;
>> + int ret;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + pdev->gadget_driver = driver;
>> +
>> + /* limit speed if necessary */
>> + max_speed = min(driver->max_speed, g->max_speed);
>> + ret = cdnsp_run(pdev, max_speed);
>> +
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * Update Event Ring Dequeue Pointer:
>> + * - When all events have finished
>> + * - To avoid "Event Ring Full Error" condition
>> + */
>> +void cdnsp_update_erst_dequeue(struct cdnsp_device *pdev,
>> + union cdnsp_trb *event_ring_deq,
>> + u8 clear_ehb)
>> +{
>> + u64 temp_64;
>> + dma_addr_t deq;
>> +
>> + temp_64 = cdnsp_read_64(pdev, &pdev->ir_set->erst_dequeue);
>> +
>> + /* If necessary, update the HW's version of the event ring deq ptr. */
>> + if (event_ring_deq != pdev->event_ring->dequeue) {
>> + deq = cdnsp_trb_virt_to_dma(pdev->event_ring->deq_seg,
>> + pdev->event_ring->dequeue);
>> + temp_64 &= ERST_PTR_MASK;
>> + temp_64 |= ((u64)deq & (u64)~ERST_PTR_MASK);
>> + }
>> +
>> + /* Clear the event handler busy flag (RW1C). */
>> + if (clear_ehb)
>> + temp_64 |= ERST_EHB;
>> + else
>> + temp_64 &= ~ERST_EHB;
>> +
>> + cdnsp_write_64(pdev, temp_64, &pdev->ir_set->erst_dequeue);
>> +}
>> +
>> +static void cdnsp_clear_cmd_ring(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_segment *seg;
>> + u64 val_64;
>> + int i;
>> +
>> + cdnsp_initialize_ring_info(pdev->cmd_ring);
>> +
>> + seg = pdev->cmd_ring->first_seg;
>> + for (i = 0; i < pdev->cmd_ring->num_segs; i++) {
>> + memset(seg->trbs, 0,
>> + sizeof(union cdnsp_trb) * (TRBS_PER_SEGMENT - 1));
>> + seg = seg->next;
>> + }
>> +
>> + /* Set the address in the Command Ring Control register. */
>> + val_64 = cdnsp_read_64(pdev, &pdev->op_regs->cmd_ring);
>> + val_64 = (val_64 & (u64)CMD_RING_RSVD_BITS) |
>> + (pdev->cmd_ring->first_seg->dma & (u64)~CMD_RING_RSVD_BITS) |
>> + pdev->cmd_ring->cycle_state;
>> + cdnsp_write_64(pdev, val_64, &pdev->op_regs->cmd_ring);
>> +}
>> +
>> +static void cdnsp_consume_all_events(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_segment *event_deq_seg;
>> + union cdnsp_trb *event_ring_deq;
>> + union cdnsp_trb *event;
>> + u32 cycle_bit;
>> +
>> + event_ring_deq = pdev->event_ring->dequeue;
>> + event_deq_seg = pdev->event_ring->deq_seg;
>> + event = pdev->event_ring->dequeue;
>> +
>> + /* Update ring dequeue pointer. */
>> + while (1) {
>> + cycle_bit = (le32_to_cpu(event->event_cmd.flags) & TRB_CYCLE);
>> +
>> + /* Does the controller or driver own the TRB? */
>> + if (cycle_bit != pdev->event_ring->cycle_state)
>> + break;
>> +
>> + cdnsp_inc_deq(pdev, pdev->event_ring);
>> +
>> + if (!cdnsp_last_trb_on_seg(event_deq_seg, event)) {
>> + event++;
>> + continue;
>> + }
>> +
>> + if (cdnsp_last_trb_on_ring(pdev->event_ring, event_deq_seg,
>> + event))
>> + cycle_bit ^= 1;
>> +
>> + event_deq_seg = event_deq_seg->next;
>> + event = event_deq_seg->trbs;
>> + }
>> +
>> + cdnsp_update_erst_dequeue(pdev, event_ring_deq, 1);
>> +}
>> +
>> +static void cdnsp_stop(struct cdnsp_device *pdev)
>> +{
>> + u32 temp;
>> +
>> + cdnsp_cmd_flush_ep(pdev, &pdev->eps[0]);
>> +
>> + /* Remove internally queued request for ep0. */
>> + if (!list_empty(&pdev->eps[0].pending_list)) {
>> + struct cdnsp_request *req;
>> +
>> + req = next_request(&pdev->eps[0].pending_list);
>> + if (req == &pdev->ep0_preq)
>> + cdnsp_ep_dequeue(&pdev->eps[0], req);
>> + }
>> +
>> + cdnsp_disable_port(pdev, &pdev->usb2_port.regs->portsc);
>> + cdnsp_disable_port(pdev, &pdev->usb3_port.regs->portsc);
>> + cdnsp_disable_slot(pdev);
>> + cdnsp_halt(pdev);
>> +
>> + temp = readl(&pdev->op_regs->status);
>> + writel((temp & ~0x1fff) | STS_EINT, &pdev->op_regs->status);
>> + temp = readl(&pdev->ir_set->irq_pending);
>> + writel(IMAN_IE_CLEAR(temp), &pdev->ir_set->irq_pending);
>> +
>> + cdnsp_clear_port_change_bit(pdev, &pdev->usb2_port.regs->portsc);
>> + cdnsp_clear_port_change_bit(pdev, &pdev->usb3_port.regs->portsc);
>> +
>> + /*Clear interrupt line */
>> + temp = readl(&pdev->ir_set->irq_pending);
>> + temp |= IMAN_IP;
>> + writel(temp, &pdev->ir_set->irq_pending);
>> +
>> + cdnsp_consume_all_events(pdev);
>> + cdnsp_clear_cmd_ring(pdev);
>> +}
>> +
>> +/*
>> + * Stop controller.
>> + * This function is called by the gadget core when the driver is removed.
>> + * Disable slot, disable IRQs, and quiesce the controller.
>> + */
>> +static int cdnsp_gadget_udc_stop(struct usb_gadget *g)
>> +{
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(g);
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + cdnsp_stop(pdev);
>> + pdev->gadget_driver = NULL;
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_gadget_get_frame(struct usb_gadget *g)
>> +{
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(g);
>> +
>> + return cdnsp_get_frame(pdev);
>> +}
>> +
>> +static void __cdnsp_gadget_wakeup(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_port_regs __iomem *port_regs;
>> + u32 portpm, portsc;
>> +
>> + port_regs = pdev->active_port->regs;
>> + portsc = readl(&port_regs->portsc) & PORT_PLS_MASK;
>> +
>> + /* Remote wakeup feature is not enabled by host. */
>> + if (pdev->gadget.speed < USB_SPEED_SUPER && portsc == XDEV_U2) {
>> + portpm = readl(&port_regs->portpmsc);
>> +
>> + if (!(portpm & PORT_RWE))
>> + return;
>> + }
>> +
>> + if (portsc == XDEV_U3 && !pdev->may_wakeup)
>> + return;
>> +
>> + cdnsp_set_link_state(pdev, &port_regs->portsc, XDEV_U0);
>> +
>> + pdev->cdnsp_state |= CDNSP_WAKEUP_PENDING;
>> +}
>> +
>> +static int cdnsp_gadget_wakeup(struct usb_gadget *g)
>> +{
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(g);
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + __cdnsp_gadget_wakeup(pdev);
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_gadget_set_selfpowered(struct usb_gadget *g,
>> + int is_selfpowered)
>> +{
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(g);
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + g->is_selfpowered = !!is_selfpowered;
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_gadget_pullup(struct usb_gadget *gadget, int is_on)
>> +{
>> + struct cdnsp_device *pdev = gadget_to_cdnsp(gadget);
>> + struct cdns *cdns = dev_get_drvdata(pdev->dev);
>> +
>> + if (!is_on) {
>> + cdnsp_reset_device(pdev);
>> + cdns_clear_vbus(cdns);
>> + } else {
>> + cdns_set_vbus(cdns);
>> + }
>> + return 0;
>> +}
>> +
>> +const struct usb_gadget_ops cdnsp_gadget_ops = {
>> + .get_frame = cdnsp_gadget_get_frame,
>> + .wakeup = cdnsp_gadget_wakeup,
>> + .set_selfpowered = cdnsp_gadget_set_selfpowered,
>> + .pullup = cdnsp_gadget_pullup,
>> + .udc_start = cdnsp_gadget_udc_start,
>> + .udc_stop = cdnsp_gadget_udc_stop,
>> +};
>> +
>> +static void cdnsp_get_ep_buffering(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep)
>> +{
>> + void __iomem *reg = &pdev->cap_regs->hc_capbase;
>> + int endpoints;
>> +
>> + reg += cdnsp_find_next_ext_cap(reg, 0, XBUF_CAP_ID);
>> +
>> + if (!pep->direction) {
>> + pep->buffering = readl(reg + XBUF_RX_TAG_MASK_0_OFFSET);
>> + pep->buffering_period = readl(reg + XBUF_RX_TAG_MASK_1_OFFSET);
>> + pep->buffering = (pep->buffering + 1) / 2;
>> + pep->buffering_period = (pep->buffering_period + 1) / 2;
>> + return;
>> + }
>> +
>> + endpoints = HCS_ENDPOINTS(readl(&pdev->hcs_params1)) / 2;
>> +
>> + /* Set to XBUF_TX_TAG_MASK_0 register. */
>> + reg += XBUF_TX_CMD_OFFSET + (endpoints * 2 + 2) * sizeof(u32);
>> + /* Set reg to XBUF_TX_TAG_MASK_N related with this endpoint. */
>> + reg += pep->number * sizeof(u32) * 2;
>> +
>> + pep->buffering = (readl(reg) + 1) / 2;
>> + pep->buffering_period = pep->buffering;
>> +}
>> +
>> +static int cdnsp_gadget_init_endpoints(struct cdnsp_device *pdev)
>> +{
>> + int max_streams = HCC_MAX_PSA(pdev->hcc_params);
>> + struct cdnsp_ep *pep;
>> + int i;
>> +
>> + INIT_LIST_HEAD(&pdev->gadget.ep_list);
>> +
>> + if (max_streams < STREAM_LOG_STREAMS) {
>> + dev_err(pdev->dev, "Stream size %d not supported\n",
>> + max_streams);
>> + return -EINVAL;
>> + }
>> +
>> + max_streams = STREAM_LOG_STREAMS;
>> +
>> + for (i = 0; i < CDNSP_ENDPOINTS_NUM; i++) {
>> + bool direction = !(i & 1); /* Start from OUT endpoint. */
>> + u8 epnum = ((i + 1) >> 1);
>> +
>> + if (!CDNSP_IF_EP_EXIST(pdev, epnum, direction))
>> + continue;
>> +
>> + pep = &pdev->eps[i];
>> + pep->pdev = pdev;
>> + pep->number = epnum;
>> + pep->direction = direction; /* 0 for OUT, 1 for IN. */
>> +
>> + /*
>> + * Ep0 is bidirectional, so ep0in and ep0out are represented by
>> + * pdev->eps[0]
>> + */
>> + if (epnum == 0) {
>> + snprintf(pep->name, sizeof(pep->name), "ep%d%s",
>> + epnum, "BiDir");
>> +
>> + pep->idx = 0;
>> + usb_ep_set_maxpacket_limit(&pep->endpoint, 512);
>> + pep->endpoint.maxburst = 1;
>> + pep->endpoint.ops = &cdnsp_gadget_ep0_ops;
>> + pep->endpoint.desc = &cdnsp_gadget_ep0_desc;
>> + pep->endpoint.comp_desc = NULL;
>> + pep->endpoint.caps.type_control = true;
>> + pep->endpoint.caps.dir_in = true;
>> + pep->endpoint.caps.dir_out = true;
>> +
>> + pdev->ep0_preq.epnum = pep->number;
>> + pdev->ep0_preq.pep = pep;
>> + pdev->gadget.ep0 = &pep->endpoint;
>> + } else {
>> + snprintf(pep->name, sizeof(pep->name), "ep%d%s",
>> + epnum, (pep->direction) ? "in" : "out");
>> +
>> + pep->idx = (epnum * 2 + (direction ? 1 : 0)) - 1;
>> + usb_ep_set_maxpacket_limit(&pep->endpoint, 1024);
>> +
>> + pep->endpoint.max_streams = max_streams;
>> + pep->endpoint.ops = &cdnsp_gadget_ep_ops;
>> + list_add_tail(&pep->endpoint.ep_list,
>> + &pdev->gadget.ep_list);
>> +
>> + pep->endpoint.caps.type_iso = true;
>> + pep->endpoint.caps.type_bulk = true;
>> + pep->endpoint.caps.type_int = true;
>> +
>> + pep->endpoint.caps.dir_in = direction;
>> + pep->endpoint.caps.dir_out = !direction;
>> + }
>> +
>> + pep->endpoint.name = pep->name;
>> + pep->in_ctx = cdnsp_get_ep_ctx(&pdev->in_ctx, pep->idx);
>> + pep->out_ctx = cdnsp_get_ep_ctx(&pdev->out_ctx, pep->idx);
>> + cdnsp_get_ep_buffering(pdev, pep);
>> +
>> + dev_dbg(pdev->dev, "Init %s, MPS: %04x SupType: "
>> + "CTRL: %s, INT: %s, BULK: %s, ISOC %s, "
>> + "SupDir IN: %s, OUT: %s\n",
>> + pep->name, 1024,
>> + (pep->endpoint.caps.type_control) ? "yes" : "no",
>> + (pep->endpoint.caps.type_int) ? "yes" : "no",
>> + (pep->endpoint.caps.type_bulk) ? "yes" : "no",
>> + (pep->endpoint.caps.type_iso) ? "yes" : "no",
>> + (pep->endpoint.caps.dir_in) ? "yes" : "no",
>> + (pep->endpoint.caps.dir_out) ? "yes" : "no");
>> +
>> + INIT_LIST_HEAD(&pep->pending_list);
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static void cdnsp_gadget_free_endpoints(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_ep *pep;
>> + int i;
>> +
>> + for (i = 0; i < CDNSP_ENDPOINTS_NUM; i++) {
>> + pep = &pdev->eps[i];
>> + if (pep->number != 0 && pep->out_ctx)
>> + list_del(&pep->endpoint.ep_list);
>> + }
>> +}
>> +
>> +void cdnsp_disconnect_gadget(struct cdnsp_device *pdev)
>> +{
>> + pdev->cdnsp_state |= CDNSP_STATE_DISCONNECT_PENDING;
>> +
>> + if (pdev->gadget_driver && pdev->gadget_driver->disconnect) {
>> + spin_unlock(&pdev->lock);
>> + pdev->gadget_driver->disconnect(&pdev->gadget);
>> + spin_lock(&pdev->lock);
>> + }
>> +
>> + pdev->gadget.speed = USB_SPEED_UNKNOWN;
>> + usb_gadget_set_state(&pdev->gadget, USB_STATE_NOTATTACHED);
>> +
>> + pdev->cdnsp_state &= ~CDNSP_STATE_DISCONNECT_PENDING;
>> +}
>> +
>> +void cdnsp_suspend_gadget(struct cdnsp_device *pdev)
>> +{
>> + if (pdev->gadget_driver && pdev->gadget_driver->suspend) {
>> + spin_unlock(&pdev->lock);
>> + pdev->gadget_driver->suspend(&pdev->gadget);
>> + spin_lock(&pdev->lock);
>> + }
>> +}
>> +
>> +void cdnsp_resume_gadget(struct cdnsp_device *pdev)
>> +{
>> + if (pdev->gadget_driver && pdev->gadget_driver->resume) {
>> + spin_unlock(&pdev->lock);
>> + pdev->gadget_driver->resume(&pdev->gadget);
>> + spin_lock(&pdev->lock);
>> + }
>> +}
>> +
>> +void cdnsp_irq_reset(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_port_regs __iomem *port_regs;
>> +
>> + cdnsp_reset_device(pdev);
>> +
>> + port_regs = pdev->active_port->regs;
>> + pdev->gadget.speed = cdnsp_port_speed(readl(port_regs));
>> +
>> + spin_unlock(&pdev->lock);
>> + usb_gadget_udc_reset(&pdev->gadget, pdev->gadget_driver);
>> + spin_lock(&pdev->lock);
>> +
>> + switch (pdev->gadget.speed) {
>> + case USB_SPEED_SUPER_PLUS:
>> + case USB_SPEED_SUPER:
>> + cdnsp_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(512);
>> + pdev->gadget.ep0->maxpacket = 512;
>> + break;
>> + case USB_SPEED_HIGH:
>> + case USB_SPEED_FULL:
>> + cdnsp_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(64);
>> + pdev->gadget.ep0->maxpacket = 64;
>> + break;
>> + default:
>> + /* Low speed is not supported. */
>> + dev_err(pdev->dev, "Unknown device speed\n");
>> + break;
>> + }
>> +
>> + cdnsp_clear_chicken_bits_2(pdev, CHICKEN_XDMA_2_TP_CACHE_DIS);
>> + cdnsp_setup_device(pdev, SETUP_CONTEXT_ONLY);
>> + usb_gadget_set_state(&pdev->gadget, USB_STATE_DEFAULT);
>> +}
>> +
>> +static void cdnsp_get_rev_cap(struct cdnsp_device *pdev)
>> +{
>> + void __iomem *reg = &pdev->cap_regs->hc_capbase;
>> + struct cdnsp_rev_cap *rev_cap;
>> +
>> + reg += cdnsp_find_next_ext_cap(reg, 0, RTL_REV_CAP);
>> + rev_cap = reg;
>> +
>> + pdev->rev_cap.ctrl_revision = readl(&rev_cap->ctrl_revision);
>> + pdev->rev_cap.rtl_revision = readl(&rev_cap->rtl_revision);
>> + pdev->rev_cap.ep_supported = readl(&rev_cap->ep_supported);
>> + pdev->rev_cap.ext_cap = readl(&rev_cap->ext_cap);
>> + pdev->rev_cap.rx_buff_size = readl(&rev_cap->rx_buff_size);
>> + pdev->rev_cap.tx_buff_size = readl(&rev_cap->tx_buff_size);
>> +
>> + dev_info(pdev->dev, "Rev: %08x/%08x, eps: %08x, buff: %08x/%08x\n",
>> + pdev->rev_cap.ctrl_revision, pdev->rev_cap.rtl_revision,
>> + pdev->rev_cap.ep_supported, pdev->rev_cap.rx_buff_size,
>> + pdev->rev_cap.tx_buff_size);
>> +}
>> +
>> +static int cdnsp_gen_setup(struct cdnsp_device *pdev)
>> +{
>> + int ret;
>> +
>> + pdev->cap_regs = pdev->regs;
>> + pdev->op_regs = pdev->regs +
>> + HC_LENGTH(readl(&pdev->cap_regs->hc_capbase));
>> + pdev->run_regs = pdev->regs +
>> + (readl(&pdev->cap_regs->run_regs_off) & RTSOFF_MASK);
>> +
>> + /* Cache read-only capability registers */
>> + pdev->hcs_params1 = readl(&pdev->cap_regs->hcs_params1);
>> + pdev->hcc_params = readl(&pdev->cap_regs->hc_capbase);
>> + pdev->hci_version = HC_VERSION(pdev->hcc_params);
>> + pdev->hcc_params = readl(&pdev->cap_regs->hcc_params);
>> +
>> + cdnsp_get_rev_cap(pdev);
>> +
>> + /* Make sure the Device Controller is halted. */
>> + ret = cdnsp_halt(pdev);
>> + if (ret)
>> + return ret;
>> +
>> + /* Reset the internal controller memory state and registers. */
>> + ret = cdnsp_reset(pdev);
>> + if (ret)
>> + return ret;
>> +
>> + /*
>> + * Set dma_mask and coherent_dma_mask to 64-bits,
>> + * if controller supports 64-bit addressing.
>> + */
>> + if (HCC_64BIT_ADDR(pdev->hcc_params) &&
>> + !dma_set_mask(pdev->dev, DMA_BIT_MASK(64))) {
>> + dev_dbg(pdev->dev, "Enabling 64-bit DMA addresses.\n");
>> + dma_set_coherent_mask(pdev->dev, DMA_BIT_MASK(64));
>> + } else {
>> + /*
>> + * This is to avoid error in cases where a 32-bit USB
>> + * controller is used on a 64-bit capable system.
>> + */
>> + ret = dma_set_mask(pdev->dev, DMA_BIT_MASK(32));
>> + if (ret)
>> + return ret;
>> + dev_dbg(pdev->dev, "Enabling 32-bit DMA addresses.\n");
>> + dma_set_coherent_mask(pdev->dev, DMA_BIT_MASK(32));
>> + }
>> +
>> + spin_lock_init(&pdev->lock);
>> +
>> + ret = cdnsp_mem_init(pdev, GFP_KERNEL);
>> + if (ret)
>> + return ret;
>> +
>> + return 0;
>> +}
>> +
>> +static int __cdnsp_gadget_init(struct cdns *cdns)
>> +{
>> + struct cdnsp_device *pdev;
>> + u32 max_speed;
>> + int ret = -ENOMEM;
>> +
>> + cdns_drd_gadget_on(cdns);
>> +
>> + pdev = kzalloc(sizeof(*pdev), GFP_KERNEL);
>> + if (!pdev)
>> + return -ENOMEM;
>> +
>> + pm_runtime_get_sync(cdns->dev);
>> +
>> + cdns->gadget_dev = pdev;
>> + pdev->dev = cdns->dev;
>> + pdev->regs = cdns->dev_regs;
>> + max_speed = usb_get_maximum_speed(cdns->dev);
>> +
>> + switch (max_speed) {
>> + case USB_SPEED_FULL:
>> + case USB_SPEED_HIGH:
>> + case USB_SPEED_SUPER:
>> + case USB_SPEED_SUPER_PLUS:
>> + break;
>> + default:
>> + dev_err(cdns->dev, "invalid speed parameter %d\n", max_speed);
>> + fallthrough;
>> + case USB_SPEED_UNKNOWN:
>> + /* Default to SSP */
>> + max_speed = USB_SPEED_SUPER_PLUS;
>> + break;
>> + }
>> +
>> + pdev->gadget.ops = &cdnsp_gadget_ops;
>> + pdev->gadget.name = "cdnsp-gadget";
>> + pdev->gadget.speed = USB_SPEED_UNKNOWN;
>> + pdev->gadget.sg_supported = 1;
>> + pdev->gadget.max_speed = USB_SPEED_SUPER_PLUS;
>> + pdev->gadget.lpm_capable = 1;
>> +
>> + pdev->setup_buf = kzalloc(CDNSP_EP0_SETUP_SIZE, GFP_KERNEL);
>> + if (!pdev->setup_buf)
>> + goto free_pdev;
>> +
>> + /*
>> + * Controller supports not aligned buffer but it should improve
>> + * performance.
>> + */
>> + pdev->gadget.quirk_ep_out_aligned_size = true;
>> +
>> + ret = cdnsp_gen_setup(pdev);
>> + if (ret) {
>> + dev_err(pdev->dev, "Generic initialization failed %d\n", ret);
>> + goto free_setup;
>> + }
>> +
>> + ret = cdnsp_gadget_init_endpoints(pdev);
>> + if (ret) {
>> + dev_err(pdev->dev, "failed to initialize endpoints\n");
>> + goto halt_pdev;
>> + }
>> +
>> + ret = usb_add_gadget_udc(pdev->dev, &pdev->gadget);
>> + if (ret) {
>> + dev_err(pdev->dev, "failed to register udc\n");
>> + goto free_endpoints;
>> + }
>> +
>> + ret = devm_request_threaded_irq(pdev->dev, cdns->dev_irq,
>> + cdnsp_irq_handler,
>> + cdnsp_thread_irq_handler, IRQF_SHARED,
>> + dev_name(pdev->dev), pdev);
>> + if (ret)
>> + goto del_gadget;
>> +
>> + return 0;
>> +
>> +del_gadget:
>> + usb_del_gadget_udc(&pdev->gadget);
>> +free_endpoints:
>> + cdnsp_gadget_free_endpoints(pdev);
>> +halt_pdev:
>> + cdnsp_halt(pdev);
>> + cdnsp_reset(pdev);
>> + cdnsp_mem_cleanup(pdev);
>> +free_setup:
>> + kfree(pdev->setup_buf);
>> +free_pdev:
>> + kfree(pdev);
>> +
>> + return ret;
>> +}
>> +
>> +static void cdnsp_gadget_exit(struct cdns *cdns)
>> +{
>> + struct cdnsp_device *pdev = cdns->gadget_dev;
>> +
>> + devm_free_irq(pdev->dev, cdns->dev_irq, pdev);
>> + pm_runtime_mark_last_busy(cdns->dev);
>> + pm_runtime_put_autosuspend(cdns->dev);
>> + usb_del_gadget_udc(&pdev->gadget);
>> + cdnsp_gadget_free_endpoints(pdev);
>> + cdnsp_mem_cleanup(pdev);
>> + kfree(pdev);
>> + cdns->gadget_dev = NULL;
>> + cdns_drd_gadget_off(cdns);
>> +}
>> +
>> +static int cdnsp_gadget_suspend(struct cdns *cdns, bool do_wakeup)
>> +{
>> + struct cdnsp_device *pdev = cdns->gadget_dev;
>> + unsigned long flags;
>> +
>> + if (pdev->link_state == XDEV_U3)
>> + return 0;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + cdnsp_disconnect_gadget(pdev);
>> + cdnsp_stop(pdev);
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_gadget_resume(struct cdns *cdns, bool hibernated)
>> +{
>> + struct cdnsp_device *pdev = cdns->gadget_dev;
>> + enum usb_device_speed max_speed;
>> + unsigned long flags;
>> + int ret;
>> +
>> + if (!pdev->gadget_driver)
>> + return 0;
>> +
>> + spin_lock_irqsave(&pdev->lock, flags);
>> + max_speed = pdev->gadget_driver->max_speed;
>> +
>> + /* Limit speed if necessary. */
>> + max_speed = min(max_speed, pdev->gadget.max_speed);
>> +
>> + ret = cdnsp_run(pdev, max_speed);
>> +
>> + if (pdev->link_state == XDEV_U3)
>> + __cdnsp_gadget_wakeup(pdev);
>> +
>> + spin_unlock_irqrestore(&pdev->lock, flags);
>> +
>> + return ret;
>> +}
>> +
>> +/**
>> + * cdnsp_gadget_init - initialize device structure
>> + * @cdns: cdnsp instance
>> + *
>> + * This function initializes the gadget.
>> + */
>> +int cdnsp_gadget_init(struct cdns *cdns)
>> +{
>> + struct cdns_role_driver *rdrv;
>> +
>> + rdrv = devm_kzalloc(cdns->dev, sizeof(*rdrv), GFP_KERNEL);
>> + if (!rdrv)
>> + return -ENOMEM;
>> +
>> + rdrv->start = __cdnsp_gadget_init;
>> + rdrv->stop = cdnsp_gadget_exit;
>> + rdrv->suspend = cdnsp_gadget_suspend;
>> + rdrv->resume = cdnsp_gadget_resume;
>> + rdrv->state = CDNS_ROLE_STATE_INACTIVE;
>> + rdrv->name = "gadget";
>> + cdns->roles[USB_ROLE_DEVICE] = rdrv;
>> +
>> + return 0;
>> +}
>> +EXPORT_SYMBOL_GPL(cdnsp_gadget_init);
>> diff --git a/drivers/usb/cdnsp/gadget.h b/drivers/usb/cdnsp/gadget.h
>> index bfc4196c3b10..547516681fbe 100644
>> --- a/drivers/usb/cdnsp/gadget.h
>> +++ b/drivers/usb/cdnsp/gadget.h
>> @@ -1456,4 +1456,143 @@ struct cdnsp_device {
>> u16 test_mode;
>> };
>>
>> +/*
>> + * Registers should always be accessed with double word or quad word accesses.
>> + *
>> + * Registers with 64-bit address pointers should be written to with
>> + * dword accesses by writing the low dword first (ptr[0]), then the high dword
>> + * (ptr[1]) second. controller implementations that do not support 64-bit
>> + * address pointers will ignore the high dword, and write order is irrelevant.
>> + */
>> +static inline u64 cdnsp_read_64(const struct cdnsp_device *pdev,
>> + __le64 __iomem *regs)
>> +{
>> + return lo_hi_readq(regs);
>> +}
>> +
>> +static inline void cdnsp_write_64(struct cdnsp_device *pdev,
>> + const u64 val, __le64 __iomem *regs)
>> +{
>> + lo_hi_writeq(val, regs);
>> +}
>> +
>> +/* CDNSP memory management functions. */
>> +void cdnsp_mem_cleanup(struct cdnsp_device *pdev);
>> +int cdnsp_mem_init(struct cdnsp_device *pdev, gfp_t flags);
>> +int cdnsp_setup_addressable_priv_dev(struct cdnsp_device *pdev);
>> +void cdnsp_copy_ep0_dequeue_into_input_ctx(struct cdnsp_device *pdev);
>> +void cdnsp_endpoint_zero(struct cdnsp_device *pdev, struct cdnsp_ep *ep);
>> +int cdnsp_endpoint_init(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep,
>> + gfp_t mem_flags);
>> +int cdnsp_ring_expansion(struct cdnsp_device *pdev,
>> + struct cdnsp_ring *ring,
>> + unsigned int num_trbs, gfp_t flags);
>> +struct cdnsp_ring *cdnsp_dma_to_transfer_ring(struct cdnsp_ep *ep, u64 address);
>> +int cdnsp_alloc_stream_info(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep,
>> + unsigned int num_stream_ctxs,
>> + unsigned int num_streams);
>> +int cdnsp_alloc_streams(struct cdnsp_device *pdev, struct cdnsp_ep *pep);
>> +void cdnsp_free_endpoint_rings(struct cdnsp_device *pdev, struct cdnsp_ep *pep);
>> +
>> +/* Device controller glue. */
>> +int cdnsp_find_next_ext_cap(void __iomem *base, u32 start, int id);
>> +int cdnsp_halt(struct cdnsp_device *pdev);
>> +void cdnsp_died(struct cdnsp_device *pdev);
>> +int cdnsp_reset(struct cdnsp_device *pdev);
>> +irqreturn_t cdnsp_irq_handler(int irq, void *priv);
>> +int cdnsp_setup_device(struct cdnsp_device *pdev, enum cdnsp_setup_dev setup);
>> +void cdnsp_set_usb2_hardware_lpm(struct cdnsp_device *usbsssp_data,
>> + struct usb_request *req, int enable);
>> +irqreturn_t cdnsp_thread_irq_handler(int irq, void *data);
>> +
>> +/* Ring, segment, TRB, and TD functions. */
>> +dma_addr_t cdnsp_trb_virt_to_dma(struct cdnsp_segment *seg,
>> + union cdnsp_trb *trb);
>> +bool cdnsp_last_trb_on_seg(struct cdnsp_segment *seg, union cdnsp_trb *trb);
>> +bool cdnsp_last_trb_on_ring(struct cdnsp_ring *ring,
>> + struct cdnsp_segment *seg,
>> + union cdnsp_trb *trb);
>> +int cdnsp_wait_for_cmd_compl(struct cdnsp_device *pdev);
>> +void cdnsp_update_erst_dequeue(struct cdnsp_device *pdev,
>> + union cdnsp_trb *event_ring_deq,
>> + u8 clear_ehb);
>> +void cdnsp_initialize_ring_info(struct cdnsp_ring *ring);
>> +void cdnsp_ring_cmd_db(struct cdnsp_device *pdev);
>> +void cdnsp_queue_slot_control(struct cdnsp_device *pdev, u32 trb_type);
>> +void cdnsp_queue_address_device(struct cdnsp_device *pdev,
>> + dma_addr_t in_ctx_ptr,
>> + enum cdnsp_setup_dev setup);
>> +void cdnsp_queue_stop_endpoint(struct cdnsp_device *pdev,
>> + unsigned int ep_index);
>> +int cdnsp_queue_ctrl_tx(struct cdnsp_device *pdev, struct cdnsp_request *preq);
>> +int cdnsp_queue_bulk_tx(struct cdnsp_device *pdev, struct cdnsp_request *preq);
>> +int cdnsp_queue_isoc_tx_prepare(struct cdnsp_device *pdev,
>> + struct cdnsp_request *preq);
>> +void cdnsp_queue_configure_endpoint(struct cdnsp_device *pdev,
>> + dma_addr_t in_ctx_ptr);
>> +void cdnsp_queue_reset_ep(struct cdnsp_device *pdev, unsigned int ep_index);
>> +void cdnsp_queue_halt_endpoint(struct cdnsp_device *pdev,
>> + unsigned int ep_index);
>> +void cdnsp_queue_flush_endpoint(struct cdnsp_device *pdev,
>> + unsigned int ep_index);
>> +void cdnsp_force_header_wakeup(struct cdnsp_device *pdev, int intf_num);
>> +void cdnsp_queue_reset_device(struct cdnsp_device *pdev);
>> +void cdnsp_queue_new_dequeue_state(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep,
>> + struct cdnsp_dequeue_state *deq_state);
>> +void cdnsp_ring_doorbell_for_active_rings(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep);
>> +void cdnsp_inc_deq(struct cdnsp_device *pdev, struct cdnsp_ring *ring);
>> +void cdnsp_set_link_state(struct cdnsp_device *pdev,
>> + __le32 __iomem *port_regs, u32 link_state);
>> +u32 cdnsp_port_state_to_neutral(u32 state);
>> +
>> +/* CDNSP device controller contexts. */
>> +int cdnsp_enable_slot(struct cdnsp_device *pdev);
>> +int cdnsp_disable_slot(struct cdnsp_device *pdev);
>> +struct cdnsp_input_control_ctx
>> + *cdnsp_get_input_control_ctx(struct cdnsp_container_ctx *ctx);
>> +struct cdnsp_slot_ctx *cdnsp_get_slot_ctx(struct cdnsp_container_ctx *ctx);
>> +struct cdnsp_ep_ctx *cdnsp_get_ep_ctx(struct cdnsp_container_ctx *ctx,
>> + unsigned int ep_index);
>> +/* CDNSP gadget interface. */
>> +void cdnsp_suspend_gadget(struct cdnsp_device *pdev);
>> +void cdnsp_resume_gadget(struct cdnsp_device *pdev);
>> +void cdnsp_disconnect_gadget(struct cdnsp_device *pdev);
>> +void cdnsp_gadget_giveback(struct cdnsp_ep *pep, struct cdnsp_request *preq,
>> + int status);
>> +int cdnsp_ep_enqueue(struct cdnsp_ep *pep, struct cdnsp_request *preq);
>> +int cdnsp_ep_dequeue(struct cdnsp_ep *pep, struct cdnsp_request *preq);
>> +unsigned int cdnsp_port_speed(unsigned int port_status);
>> +void cdnsp_irq_reset(struct cdnsp_device *pdev);
>> +int cdnsp_halt_endpoint(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep, int value);
>> +int cdnsp_cmd_stop_ep(struct cdnsp_device *pdev, struct cdnsp_ep *pep);
>> +int cdnsp_cmd_flush_ep(struct cdnsp_device *pdev, struct cdnsp_ep *pep);
>> +void cdnsp_setup_analyze(struct cdnsp_device *pdev);
>> +int cdnsp_status_stage(struct cdnsp_device *pdev);
>> +int cdnsp_reset_device(struct cdnsp_device *pdev);
>> +
>> +/**
>> + * next_request - gets the next request on the given list
>> + * @list: the request list to operate on
>> + *
>> + * Caller should take care of locking. This function return NULL or the first
>> + * request available on list.
>> + */
>> +static inline struct cdnsp_request *next_request(struct list_head *list)
>> +{
>> + return list_first_entry_or_null(list, struct cdnsp_request, list);
>> +}
>> +
>> +#define to_cdnsp_ep(ep) (container_of(ep, struct cdnsp_ep, endpoint))
>> +#define gadget_to_cdnsp(g) (container_of(g, struct cdnsp_device, gadget))
>> +#define request_to_cdnsp_request(r) (container_of(r, struct cdnsp_request, \
>> + request))
>> +#define to_cdnsp_request(r) (container_of(r, struct cdnsp_request, request))
>> +int cdnsp_remove_request(struct cdnsp_device *pdev, struct cdnsp_request *preq,
>> + struct cdnsp_ep *pep);
>> +
>> #endif /* __LINUX_CDNSP_GADGET_H */
>> diff --git a/drivers/usb/cdnsp/mem.c b/drivers/usb/cdnsp/mem.c
>> new file mode 100644
>> index 000000000000..09662574adeb
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/mem.c
>> @@ -0,0 +1,1312 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Cadence CDNSP DRD Driver.
>> + *
>> + * Copyright (C) 2020 Cadence.
>> + *
>> + * Author: Pawel Laszczak <[email protected]>
>> + *
>> + * Code based on Linux XHCI driver.
>> + * Origin: Copyright (C) 2008 Intel Corp.
>> + */
>> +
>> +#include <linux/dma-mapping.h>
>> +#include <linux/dmapool.h>
>> +#include <linux/slab.h>
>> +#include <linux/usb.h>
>> +
>> +#include "gadget.h"
>> +
>> +static void cdnsp_free_stream_info(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep);
>> +/*
>> + * Allocates a generic ring segment from the ring pool, sets the dma address,
>> + * initializes the segment to zero, and sets the private next pointer to NULL.
>> + *
>> + * "All components of all Command and Transfer TRBs shall be initialized to '0'"
>> + */
>> +static struct cdnsp_segment *cdnsp_segment_alloc(struct cdnsp_device *pdev,
>> + unsigned int cycle_state,
>> + unsigned int max_packet,
>> + gfp_t flags)
>> +{
>> + struct cdnsp_segment *seg;
>> + dma_addr_t dma;
>> + int i;
>> +
>> + seg = kzalloc(sizeof(*seg), flags);
>> + if (!seg)
>> + return NULL;
>> +
>> + seg->trbs = dma_pool_zalloc(pdev->segment_pool, flags, &dma);
>> + if (!seg->trbs) {
>> + kfree(seg);
>> + return NULL;
>> + }
>> +
>> + if (max_packet) {
>> + seg->bounce_buf = kzalloc(max_packet, flags | GFP_DMA);
>> + if (!seg->bounce_buf)
>> + goto free_dma;
>> + }
>> +
>> + /* If the cycle state is 0, set the cycle bit to 1 for all the TRBs. */
>> + if (cycle_state == 0) {
>> + for (i = 0; i < TRBS_PER_SEGMENT; i++)
>> + seg->trbs[i].link.control |= cpu_to_le32(TRB_CYCLE);
>> + }
>> + seg->dma = dma;
>> + seg->next = NULL;
>> +
>> + return seg;
>> +
>> +free_dma:
>> + dma_pool_free(pdev->segment_pool, seg->trbs, dma);
>> + kfree(seg);
>> +
>> + return NULL;
>> +}
>> +
>> +static void cdnsp_segment_free(struct cdnsp_device *pdev,
>> + struct cdnsp_segment *seg)
>> +{
>> + if (seg->trbs)
>> + dma_pool_free(pdev->segment_pool, seg->trbs, seg->dma);
>> +
>> + kfree(seg->bounce_buf);
>> + kfree(seg);
>> +}
>> +
>> +static void cdnsp_free_segments_for_ring(struct cdnsp_device *pdev,
>> + struct cdnsp_segment *first)
>> +{
>> + struct cdnsp_segment *seg;
>> +
>> + seg = first->next;
>> +
>> + while (seg != first) {
>> + struct cdnsp_segment *next = seg->next;
>> +
>> + cdnsp_segment_free(pdev, seg);
>> + seg = next;
>> + }
>> +
>> + cdnsp_segment_free(pdev, first);
>> +}
>> +
>> +/*
>> + * Make the prev segment point to the next segment.
>> + *
>> + * Change the last TRB in the prev segment to be a Link TRB which points to the
>> + * DMA address of the next segment. The caller needs to set any Link TRB
>> + * related flags, such as End TRB, Toggle Cycle, and no snoop.
>> + */
>> +static void cdnsp_link_segments(struct cdnsp_device *pdev,
>> + struct cdnsp_segment *prev,
>> + struct cdnsp_segment *next,
>> + enum cdnsp_ring_type type)
>> +{
>> + struct cdnsp_link_trb *link;
>> + u32 val;
>> +
>> + if (!prev || !next)
>> + return;
>> +
>> + prev->next = next;
>> + if (type != TYPE_EVENT) {
>> + link = &prev->trbs[TRBS_PER_SEGMENT - 1].link;
>> + link->segment_ptr = cpu_to_le64(next->dma);
>> +
>> + /*
>> + * Set the last TRB in the segment to have a TRB type ID
>> + * of Link TRB
>> + */
>> + val = le32_to_cpu(link->control);
>> + val &= ~TRB_TYPE_BITMASK;
>> + val |= TRB_TYPE(TRB_LINK);
>> + link->control = cpu_to_le32(val);
>> + }
>> +}
>> +
>> +/*
>> + * Link the ring to the new segments.
>> + * Set Toggle Cycle for the new ring if needed.
>> + */
>> +static void cdnsp_link_rings(struct cdnsp_device *pdev,
>> + struct cdnsp_ring *ring,
>> + struct cdnsp_segment *first,
>> + struct cdnsp_segment *last,
>> + unsigned int num_segs)
>> +{
>> + struct cdnsp_segment *next;
>> +
>> + if (!ring || !first || !last)
>> + return;
>> +
>> + next = ring->enq_seg->next;
>> + cdnsp_link_segments(pdev, ring->enq_seg, first, ring->type);
>> + cdnsp_link_segments(pdev, last, next, ring->type);
>> + ring->num_segs += num_segs;
>> + ring->num_trbs_free += (TRBS_PER_SEGMENT - 1) * num_segs;
>> +
>> + if (ring->type != TYPE_EVENT && ring->enq_seg == ring->last_seg) {
>> + ring->last_seg->trbs[TRBS_PER_SEGMENT - 1].link.control &=
>> + ~cpu_to_le32(LINK_TOGGLE);
>> + last->trbs[TRBS_PER_SEGMENT - 1].link.control |=
>> + cpu_to_le32(LINK_TOGGLE);
>> + ring->last_seg = last;
>> + }
>> +}
>> +
>> +/*
>> + * We need a radix tree for mapping physical addresses of TRBs to which stream
>> + * ID they belong to. We need to do this because the device controller won't
>> + * tell us which stream ring the TRB came from. We could store the stream ID
>> + * in an event data TRB, but that doesn't help us for the cancellation case,
>> + * since the endpoint may stop before it reaches that event data TRB.
>> + *
>> + * The radix tree maps the upper portion of the TRB DMA address to a ring
>> + * segment that has the same upper portion of DMA addresses. For example,
>> + * say I have segments of size 1KB, that are always 1KB aligned. A segment may
>> + * start at 0x10c91000 and end at 0x10c913f0. If I use the upper 10 bits, the
>> + * key to the stream ID is 0x43244. I can use the DMA address of the TRB to
>> + * pass the radix tree a key to get the right stream ID:
>> + *
>> + * 0x10c90fff >> 10 = 0x43243
>> + * 0x10c912c0 >> 10 = 0x43244
>> + * 0x10c91400 >> 10 = 0x43245
>> + *
>> + * Obviously, only those TRBs with DMA addresses that are within the segment
>> + * will make the radix tree return the stream ID for that ring.
>> + *
>> + * Caveats for the radix tree:
>> + *
>> + * The radix tree uses an unsigned long as a key pair. On 32-bit systems, an
>> + * unsigned long will be 32-bits; on a 64-bit system an unsigned long will be
>> + * 64-bits. Since we only request 32-bit DMA addresses, we can use that as the
>> + * key on 32-bit or 64-bit systems (it would also be fine if we asked for 64-bit
>> + * PCI DMA addresses on a 64-bit system). There might be a problem on 32-bit
>> + * extended systems (where the DMA address can be bigger than 32-bits),
>> + * if we allow the PCI dma mask to be bigger than 32-bits. So don't do that.
>> + */
>> +static int cdnsp_insert_segment_mapping(struct radix_tree_root *trb_address_map,
>> + struct cdnsp_ring *ring,
>> + struct cdnsp_segment *seg,
>> + gfp_t mem_flags)
>> +{
>> + unsigned long key;
>> + int ret;
>> +
>> + key = (unsigned long)(seg->dma >> TRB_SEGMENT_SHIFT);
>> +
>> + /* Skip any segments that were already added. */
>> + if (radix_tree_lookup(trb_address_map, key))
>> + return 0;
>> +
>> + ret = radix_tree_maybe_preload(mem_flags);
>> + if (ret)
>> + return ret;
>> +
>> + ret = radix_tree_insert(trb_address_map, key, ring);
>> + radix_tree_preload_end();
>> +
>> + return ret;
>> +}
>> +
>> +static void cdnsp_remove_segment_mapping(struct radix_tree_root *trb_address_map,
>> + struct cdnsp_segment *seg)
>> +{
>> + unsigned long key;
>> +
>> + key = (unsigned long)(seg->dma >> TRB_SEGMENT_SHIFT);
>> + if (radix_tree_lookup(trb_address_map, key))
>> + radix_tree_delete(trb_address_map, key);
>> +}
>> +
>> +static int cdnsp_update_stream_segment_mapping(struct radix_tree_root *trb_address_map,
>> + struct cdnsp_ring *ring,
>> + struct cdnsp_segment *first_seg,
>> + struct cdnsp_segment *last_seg,
>> + gfp_t mem_flags)
>> +{
>> + struct cdnsp_segment *failed_seg;
>> + struct cdnsp_segment *seg;
>> + int ret;
>> +
>> + seg = first_seg;
>> + do {
>> + ret = cdnsp_insert_segment_mapping(trb_address_map, ring, seg,
>> + mem_flags);
>> + if (ret)
>> + goto remove_streams;
>> + if (seg == last_seg)
>> + return 0;
>> + seg = seg->next;
>> + } while (seg != first_seg);
>> +
>> + return 0;
>> +
>> +remove_streams:
>> + failed_seg = seg;
>> + seg = first_seg;
>> + do {
>> + cdnsp_remove_segment_mapping(trb_address_map, seg);
>> + if (seg == failed_seg)
>> + return ret;
>> + seg = seg->next;
>> + } while (seg != first_seg);
>> +
>> + return ret;
>> +}
>> +
>> +static void cdnsp_remove_stream_mapping(struct cdnsp_ring *ring)
>> +{
>> + struct cdnsp_segment *seg;
>> +
>> + seg = ring->first_seg;
>> + do {
>> + cdnsp_remove_segment_mapping(ring->trb_address_map, seg);
>> + seg = seg->next;
>> + } while (seg != ring->first_seg);
>> +}
>> +
>> +static int cdnsp_update_stream_mapping(struct cdnsp_ring *ring)
>> +{
>> + return cdnsp_update_stream_segment_mapping(ring->trb_address_map, ring,
>> + ring->first_seg, ring->last_seg, GFP_ATOMIC);
>> +}
>> +
>> +static void cdnsp_ring_free(struct cdnsp_device *pdev, struct cdnsp_ring *ring)
>> +{
>> + if (!ring)
>> + return;
>> +
>> + if (ring->first_seg) {
>> + if (ring->type == TYPE_STREAM)
>> + cdnsp_remove_stream_mapping(ring);
>> +
>> + cdnsp_free_segments_for_ring(pdev, ring->first_seg);
>> + }
>> +
>> + kfree(ring);
>> +}
>> +
>> +void cdnsp_initialize_ring_info(struct cdnsp_ring *ring)
>> +{
>> + ring->enqueue = ring->first_seg->trbs;
>> + ring->enq_seg = ring->first_seg;
>> + ring->dequeue = ring->enqueue;
>> + ring->deq_seg = ring->first_seg;
>> +
>> + /*
>> + * The ring is initialized to 0. The producer must write 1 to the cycle
>> + * bit to handover ownership of the TRB, so PCS = 1. The consumer must
>> + * compare CCS to the cycle bit to check ownership, so CCS = 1.
>> + *
>> + * New rings are initialized with cycle state equal to 1; if we are
>> + * handling ring expansion, set the cycle state equal to the old ring.
>> + */
>> + ring->cycle_state = 1;
>> +
>> + /*
>> + * Each segment has a link TRB, and leave an extra TRB for SW
>> + * accounting purpose
>> + */
>> + ring->num_trbs_free = ring->num_segs * (TRBS_PER_SEGMENT - 1) - 1;
>> +}
>> +
>> +/* Allocate segments and link them for a ring. */
>> +static int cdnsp_alloc_segments_for_ring(struct cdnsp_device *pdev,
>> + struct cdnsp_segment **first,
>> + struct cdnsp_segment **last,
>> + unsigned int num_segs,
>> + unsigned int cycle_state,
>> + enum cdnsp_ring_type type,
>> + unsigned int max_packet,
>> + gfp_t flags)
>> +{
>> + struct cdnsp_segment *prev;
>> +
>> + /* Allocate first segment. */
>> + prev = cdnsp_segment_alloc(pdev, cycle_state, max_packet, flags);
>> + if (!prev)
>> + return -ENOMEM;
>> +
>> + num_segs--;
>> + *first = prev;
>> +
>> + /* Allocate all other segments. */
>> + while (num_segs > 0) {
>> + struct cdnsp_segment *next;
>> +
>> + next = cdnsp_segment_alloc(pdev, cycle_state,
>> + max_packet, flags);
>> + if (!next) {
>> + cdnsp_free_segments_for_ring(pdev, *first);
>> + return -ENOMEM;
>> + }
>> +
>> + cdnsp_link_segments(pdev, prev, next, type);
>> +
>> + prev = next;
>> + num_segs--;
>> + }
>> +
>> + cdnsp_link_segments(pdev, prev, *first, type);
>> + *last = prev;
>> +
>> + return 0;
>> +}
>> +
>> +/*
>> + * Create a new ring with zero or more segments.
>> + *
>> + * Link each segment together into a ring.
>> + * Set the end flag and the cycle toggle bit on the last segment.
>> + */
>> +static struct cdnsp_ring *cdnsp_ring_alloc(struct cdnsp_device *pdev,
>> + unsigned int num_segs,
>> + enum cdnsp_ring_type type,
>> + unsigned int max_packet,
>> + gfp_t flags)
>> +{
>> + struct cdnsp_ring *ring;
>> + int ret;
>> +
>> + ring = kzalloc(sizeof *(ring), flags);
>> + if (!ring)
>> + return NULL;
>> +
>> + ring->num_segs = num_segs;
>> + ring->bounce_buf_len = max_packet;
>> + INIT_LIST_HEAD(&ring->td_list);
>> + ring->type = type;
>> +
>> + if (num_segs == 0)
>> + return ring;
>> +
>> + ret = cdnsp_alloc_segments_for_ring(pdev, &ring->first_seg,
>> + &ring->last_seg, num_segs,
>> + 1, type, max_packet, flags);
>> + if (ret)
>> + goto fail;
>> +
>> + /* Only event ring does not use link TRB. */
>> + if (type != TYPE_EVENT)
>> + ring->last_seg->trbs[TRBS_PER_SEGMENT - 1].link.control |=
>> + cpu_to_le32(LINK_TOGGLE);
>> +
>> + cdnsp_initialize_ring_info(ring);
>> +
>> + return ring;
>> +fail:
>> + kfree(ring);
>> + return NULL;
>> +}
>> +
>> +void cdnsp_free_endpoint_rings(struct cdnsp_device *pdev, struct cdnsp_ep *pep)
>> +{
>> + cdnsp_ring_free(pdev, pep->ring);
>> + pep->ring = NULL;
>> + cdnsp_free_stream_info(pdev, pep);
>> +}
>> +
>> +/*
>> + * Expand an existing ring.
>> + * Allocate a new ring which has same segment numbers and link the two rings.
>> + */
>> +int cdnsp_ring_expansion(struct cdnsp_device *pdev,
>> + struct cdnsp_ring *ring,
>> + unsigned int num_trbs,
>> + gfp_t flags)
>> +{
>> + unsigned int num_segs_needed;
>> + struct cdnsp_segment *first;
>> + struct cdnsp_segment *last;
>> + unsigned int num_segs;
>> + int ret;
>> +
>> + num_segs_needed = (num_trbs + (TRBS_PER_SEGMENT - 1) - 1) /
>> + (TRBS_PER_SEGMENT - 1);
>> +
>> + /* Allocate number of segments we needed, or double the ring size. */
>> + num_segs = max(ring->num_segs, num_segs_needed);
>> +
>> + ret = cdnsp_alloc_segments_for_ring(pdev, &first, &last, num_segs,
>> + ring->cycle_state, ring->type,
>> + ring->bounce_buf_len, flags);
>> + if (ret)
>> + return -ENOMEM;
>> +
>> + if (ring->type == TYPE_STREAM)
>> + ret = cdnsp_update_stream_segment_mapping(ring->trb_address_map,
>> + ring, first,
>> + last, flags);
>> +
>> + if (ret) {
>> + cdnsp_free_segments_for_ring(pdev, first);
>> +
>> + return ret;
>> + }
>> +
>> + cdnsp_link_rings(pdev, ring, first, last, num_segs);
>> +
>> + return 0;
>> +}
>> +
>> +static int cdnsp_init_device_ctx(struct cdnsp_device *pdev)
>> +{
>> + int size = HCC_64BYTE_CONTEXT(pdev->hcc_params) ? 2048 : 1024;
>> +
>> + pdev->out_ctx.type = CDNSP_CTX_TYPE_DEVICE;
>> + pdev->out_ctx.size = size;
>> + pdev->out_ctx.ctx_size = CTX_SIZE(pdev->hcc_params);
>> + pdev->out_ctx.bytes = dma_pool_zalloc(pdev->device_pool, GFP_ATOMIC,
>> + &pdev->out_ctx.dma);
>> +
>> + if (!pdev->out_ctx.bytes)
>> + return -ENOMEM;
>> +
>> + pdev->in_ctx.type = CDNSP_CTX_TYPE_INPUT;
>> + pdev->in_ctx.ctx_size = pdev->out_ctx.ctx_size;
>> + pdev->in_ctx.size = size + pdev->out_ctx.ctx_size;
>> + pdev->in_ctx.bytes = dma_pool_zalloc(pdev->device_pool, GFP_ATOMIC,
>> + &pdev->in_ctx.dma);
>> +
>> + if (!pdev->in_ctx.bytes) {
>> + dma_pool_free(pdev->device_pool, pdev->out_ctx.bytes,
>> + pdev->out_ctx.dma);
>> + return -ENOMEM;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +struct cdnsp_input_control_ctx
>> + *cdnsp_get_input_control_ctx(struct cdnsp_container_ctx *ctx)
>> +{
>> + if (ctx->type != CDNSP_CTX_TYPE_INPUT)
>> + return NULL;
>> +
>> + return (struct cdnsp_input_control_ctx *)ctx->bytes;
>> +}
>> +
>> +struct cdnsp_slot_ctx *cdnsp_get_slot_ctx(struct cdnsp_container_ctx *ctx)
>> +{
>> + if (ctx->type == CDNSP_CTX_TYPE_DEVICE)
>> + return (struct cdnsp_slot_ctx *)ctx->bytes;
>> +
>> + return (struct cdnsp_slot_ctx *)(ctx->bytes + ctx->ctx_size);
>> +}
>> +
>> +struct cdnsp_ep_ctx *cdnsp_get_ep_ctx(struct cdnsp_container_ctx *ctx,
>> + unsigned int ep_index)
>> +{
>> + /* Increment ep index by offset of start of ep ctx array. */
>> + ep_index++;
>> + if (ctx->type == CDNSP_CTX_TYPE_INPUT)
>> + ep_index++;
>> +
>> + return (struct cdnsp_ep_ctx *)(ctx->bytes + (ep_index * ctx->ctx_size));
>> +}
>> +
>> +static void cdnsp_free_stream_ctx(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep)
>> +{
>> + dma_pool_free(pdev->device_pool, pep->stream_info.stream_ctx_array,
>> + pep->stream_info.ctx_array_dma);
>> +}
>> +
>> +/* The stream context array must be a power of 2. */
>> +static struct cdnsp_stream_ctx
>> + *cdnsp_alloc_stream_ctx(struct cdnsp_device *pdev, struct cdnsp_ep *pep)
>> +{
>> + size_t size = sizeof(struct cdnsp_stream_ctx) *
>> + pep->stream_info.num_stream_ctxs;
>> +
>> + if (size > CDNSP_CTX_SIZE)
>> + return NULL;
>> +
>> + /**
>> + * Driver uses intentionally the device_pool to allocated stream
>> + * context array. Device Pool has 2048 bytes of size what gives us
>> + * 128 entries.
>> + */
>> + return dma_pool_zalloc(pdev->device_pool, GFP_DMA32 | GFP_ATOMIC,
>> + &pep->stream_info.ctx_array_dma);
>> +}
>> +
>> +struct cdnsp_ring *cdnsp_dma_to_transfer_ring(struct cdnsp_ep *pep, u64 address)
>> +{
>> + if (pep->ep_state & EP_HAS_STREAMS)
>> + return radix_tree_lookup(&pep->stream_info.trb_address_map,
>> + address >> TRB_SEGMENT_SHIFT);
>> +
>> + return pep->ring;
>> +}
>> +
>> +/*
>> + * Change an endpoint's internal structure so it supports stream IDs.
>> + * The number of requested streams includes stream 0, which cannot be used by
>> + * driver.
>> + *
>> + * The number of stream contexts in the stream context array may be bigger than
>> + * the number of streams the driver wants to use. This is because the number of
>> + * stream context array entries must be a power of two.
>> + */
>> +int cdnsp_alloc_stream_info(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep,
>> + unsigned int num_stream_ctxs,
>> + unsigned int num_streams)
>> +{
>> + struct cdnsp_stream_info *stream_info;
>> + struct cdnsp_ring *cur_ring;
>> + u32 cur_stream;
>> + u64 addr;
>> + int ret;
>> + int mps;
>> +
>> + stream_info = &pep->stream_info;
>> + stream_info->num_streams = num_streams;
>> + stream_info->num_stream_ctxs = num_stream_ctxs;
>> +
>> + /* Initialize the array of virtual pointers to stream rings. */
>> + stream_info->stream_rings = kcalloc(num_streams,
>> + sizeof(struct cdnsp_ring *),
>> + GFP_ATOMIC);
>> + if (!stream_info->stream_rings)
>> + return -ENOMEM;
>> +
>> + /* Initialize the array of DMA addresses for stream rings for the HW. */
>> + stream_info->stream_ctx_array = cdnsp_alloc_stream_ctx(pdev, pep);
>> + if (!stream_info->stream_ctx_array)
>> + goto cleanup_stream_rings;
>> +
>> + memset(stream_info->stream_ctx_array, 0,
>> + sizeof(struct cdnsp_stream_ctx) * num_stream_ctxs);
>> + INIT_RADIX_TREE(&stream_info->trb_address_map, GFP_ATOMIC);
>> + mps = usb_endpoint_maxp(pep->endpoint.desc);
>> +
>> + /*
>> + * Allocate rings for all the streams that the driver will use,
>> + * and add their segment DMA addresses to the radix tree.
>> + * Stream 0 is reserved.
>> + */
>> + for (cur_stream = 1; cur_stream < num_streams; cur_stream++) {
>> + cur_ring = cdnsp_ring_alloc(pdev, 2, TYPE_STREAM, mps,
>> + GFP_ATOMIC);
>> + stream_info->stream_rings[cur_stream] = cur_ring;
>> +
>> + if (!cur_ring)
>> + goto cleanup_rings;
>> +
>> + cur_ring->stream_id = cur_stream;
>> + cur_ring->trb_address_map = &stream_info->trb_address_map;
>> +
>> + /* Set deq ptr, cycle bit, and stream context type. */
>> + addr = cur_ring->first_seg->dma | SCT_FOR_CTX(SCT_PRI_TR) |
>> + cur_ring->cycle_state;
>> +
>> + stream_info->stream_ctx_array[cur_stream].stream_ring =
>> + cpu_to_le64(addr);
>> +
>> + ret = cdnsp_update_stream_mapping(cur_ring);
>> + if (ret)
>> + goto cleanup_rings;
>> + }
>> +
>> + return 0;
>> +
>> +cleanup_rings:
>> + for (cur_stream = 1; cur_stream < num_streams; cur_stream++) {
>> + cur_ring = stream_info->stream_rings[cur_stream];
>> + if (cur_ring) {
>> + cdnsp_ring_free(pdev, cur_ring);
>> + stream_info->stream_rings[cur_stream] = NULL;
>> + }
>> + }
>> +
>> +cleanup_stream_rings:
>> + kfree(pep->stream_info.stream_rings);
>> +
>> + return -ENOMEM;
>> +}
>> +
>> +/* Frees all stream contexts associated with the endpoint. */
>> +static void cdnsp_free_stream_info(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep)
>> +{
>> + struct cdnsp_stream_info *stream_info = &pep->stream_info;
>> + struct cdnsp_ring *cur_ring;
>> + int cur_stream;
>> +
>> + if (!(pep->ep_state & EP_HAS_STREAMS))
>> + return;
>> +
>> + for (cur_stream = 1; cur_stream < stream_info->num_streams;
>> + cur_stream++) {
>> + cur_ring = stream_info->stream_rings[cur_stream];
>> + if (cur_ring) {
>> + cdnsp_ring_free(pdev, cur_ring);
>> + stream_info->stream_rings[cur_stream] = NULL;
>> + }
>> + }
>> +
>> + if (stream_info->stream_ctx_array)
>> + cdnsp_free_stream_ctx(pdev, pep);
>> +
>> + kfree(stream_info->stream_rings);
>> + pep->ep_state &= ~EP_HAS_STREAMS;
>> +}
>> +
>> +/* All the cdnsp_tds in the ring's TD list should be freed at this point.*/
>> +static void cdnsp_free_priv_device(struct cdnsp_device *pdev)
>> +{
>> + pdev->dcbaa->dev_context_ptrs[1] = 0;
>> +
>> + cdnsp_free_endpoint_rings(pdev, &pdev->eps[0]);
>> +
>> + if (pdev->in_ctx.bytes)
>> + dma_pool_free(pdev->device_pool, pdev->in_ctx.bytes,
>> + pdev->in_ctx.dma);
>> +
>> + if (pdev->out_ctx.bytes)
>> + dma_pool_free(pdev->device_pool, pdev->out_ctx.bytes,
>> + pdev->out_ctx.dma);
>> +
>> + pdev->in_ctx.bytes = NULL;
>> + pdev->out_ctx.bytes = NULL;
>> +}
>> +
>> +static int cdnsp_alloc_priv_device(struct cdnsp_device *pdev, gfp_t flags)
>> +{
>> + int ret = -ENOMEM;
>> +
>> + ret = cdnsp_init_device_ctx(pdev);
>> + if (ret)
>> + return ret;
>> +
>> + /* Allocate endpoint 0 ring. */
>> + pdev->eps[0].ring = cdnsp_ring_alloc(pdev, 2, TYPE_CTRL, 0, flags);
>> + if (!pdev->eps[0].ring)
>> + goto fail;
>> +
>> + /* Point to output device context in dcbaa. */
>> + pdev->dcbaa->dev_context_ptrs[1] = cpu_to_le64(pdev->out_ctx.dma);
>> + pdev->cmd.in_ctx = &pdev->in_ctx;
>> +
>> + return 0;
>> +fail:
>> + dma_pool_free(pdev->device_pool, pdev->out_ctx.bytes,
>> + pdev->out_ctx.dma);
>> + dma_pool_free(pdev->device_pool, pdev->in_ctx.bytes,
>> + pdev->in_ctx.dma);
>> +
>> + return ret;
>> +}
>> +
>> +void cdnsp_copy_ep0_dequeue_into_input_ctx(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_ep_ctx *ep0_ctx = pdev->eps[0].in_ctx;
>> + struct cdnsp_ring *ep_ring = pdev->eps[0].ring;
>> + dma_addr_t dma;
>> +
>> + dma = cdnsp_trb_virt_to_dma(ep_ring->enq_seg, ep_ring->enqueue);
>> + ep0_ctx->deq = cpu_to_le64(dma | ep_ring->cycle_state);
>> +}
>> +
>> +/* Setup an controller private device for a Set Address command. */
>> +int cdnsp_setup_addressable_priv_dev(struct cdnsp_device *pdev)
>> +{
>> + struct cdnsp_slot_ctx *slot_ctx;
>> + struct cdnsp_ep_ctx *ep0_ctx;
>> + u32 max_packets, port;
>> +
>> + ep0_ctx = cdnsp_get_ep_ctx(&pdev->in_ctx, 0);
>> + slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx);
>> +
>> + /* Only the control endpoint is valid - one endpoint context. */
>> + slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(1));
>> +
>> + switch (pdev->gadget.speed) {
>> + case USB_SPEED_SUPER_PLUS:
>> + slot_ctx->dev_info |= cpu_to_le32(SLOT_SPEED_SSP);
>> + max_packets = MAX_PACKET(512);
>> + break;
>> + case USB_SPEED_SUPER:
>> + slot_ctx->dev_info |= cpu_to_le32(SLOT_SPEED_SS);
>> + max_packets = MAX_PACKET(512);
>> + break;
>> + case USB_SPEED_HIGH:
>> + slot_ctx->dev_info |= cpu_to_le32(SLOT_SPEED_HS);
>> + max_packets = MAX_PACKET(64);
>> + break;
>> + case USB_SPEED_FULL:
>> + slot_ctx->dev_info |= cpu_to_le32(SLOT_SPEED_FS);
>> + max_packets = MAX_PACKET(64);
>> + break;
>> + default:
>> + /* Speed was not set , this shouldn't happen. */
>> + return -EINVAL;
>> + }
>> +
>> + port = DEV_PORT(pdev->active_port->port_num);
>> + slot_ctx->dev_port |= cpu_to_le32(port);
>> + slot_ctx->dev_state = (pdev->device_address & DEV_ADDR_MASK);
>> + ep0_ctx->tx_info = EP_AVG_TRB_LENGTH(0x8);
>> + ep0_ctx->ep_info2 = cpu_to_le32(EP_TYPE(CTRL_EP));
>> + ep0_ctx->ep_info2 |= cpu_to_le32(MAX_BURST(0) | ERROR_COUNT(3) |
>> + max_packets);
>> +
>> + ep0_ctx->deq = cpu_to_le64(pdev->eps[0].ring->first_seg->dma |
>> + pdev->eps[0].ring->cycle_state);
>> +
>> + return 0;
>> +}
>> +
>> +/*
>> + * Convert interval expressed as 2^(bInterval - 1) == interval into
>> + * straight exponent value 2^n == interval.
>> + */
>> +static unsigned int cdnsp_parse_exponent_interval(struct usb_gadget *g,
>> + struct cdnsp_ep *pep)
>> +{
>> + unsigned int interval;
>> +
>> + interval = clamp_val(pep->endpoint.desc->bInterval, 1, 16) - 1;
>> + if (interval != pep->endpoint.desc->bInterval - 1)
>> + dev_warn(&g->dev, "ep %s - rounding interval to %d %sframes\n",
>> + pep->name, 1 << interval,
>> + g->speed == USB_SPEED_FULL ? "" : "micro");
>> +
>> + /*
>> + * Full speed isoc endpoints specify interval in frames,
>> + * not microframes. We are using microframes everywhere,
>> + * so adjust accordingly.
>> + */
>> + if (g->speed == USB_SPEED_FULL)
>> + interval += 3; /* 1 frame = 2^3 uframes */
>> +
>> + /* Controller handles only up to 512ms (2^12). */
>> + if (interval > 12)
>> + interval = 12;
>> +
>> + return interval;
>> +}
>> +
>> +/*
>> + * Convert bInterval expressed in microframes (in 1-255 range) to exponent of
>> + * microframes, rounded down to nearest power of 2.
>> + */
>> +static unsigned int cdnsp_microframes_to_exponent(struct usb_gadget *g,
>> + struct cdnsp_ep *pep,
>> + unsigned int desc_interval,
>> + unsigned int min_exponent,
>> + unsigned int max_exponent)
>> +{
>> + unsigned int interval;
>> +
>> + interval = fls(desc_interval) - 1;
>> + return clamp_val(interval, min_exponent, max_exponent);
>> +}
>> +
>> +/*
>> + * Return the polling interval.
>> + *
>> + * The polling interval is expressed in "microframes". If controllers's Interval
>> + * field is set to N, it will service the endpoint every 2^(Interval)*125us.
>> + */
>> +static unsigned int cdnsp_get_endpoint_interval(struct usb_gadget *g,
>> + struct cdnsp_ep *pep)
>> +{
>> + unsigned int interval = 0;
>> +
>> + switch (g->speed) {
>> + case USB_SPEED_HIGH:
>> + case USB_SPEED_SUPER_PLUS:
>> + case USB_SPEED_SUPER:
>> + if (usb_endpoint_xfer_int(pep->endpoint.desc) ||
>> + usb_endpoint_xfer_isoc(pep->endpoint.desc))
>> + interval = cdnsp_parse_exponent_interval(g, pep);
>> + break;
>> + case USB_SPEED_FULL:
>> + if (usb_endpoint_xfer_isoc(pep->endpoint.desc)) {
>> + interval = cdnsp_parse_exponent_interval(g, pep);
>> + } else if (usb_endpoint_xfer_int(pep->endpoint.desc)) {
>> + interval = pep->endpoint.desc->bInterval << 3;
>> + interval = cdnsp_microframes_to_exponent(g, pep,
>> + interval,
>> + 3, 10);
>> + }
>> +
>> + break;
>> + default:
>> + WARN_ON(1);
>> + }
>> +
>> + return interval;
>> +}
>> +
>> +/*
>> + * The "Mult" field in the endpoint context is only set for SuperSpeed isoc eps.
>> + * High speed endpoint descriptors can define "the number of additional
>> + * transaction opportunities per microframe", but that goes in the Max Burst
>> + * endpoint context field.
>> + */
>> +static u32 cdnsp_get_endpoint_mult(struct usb_gadget *g, struct cdnsp_ep *pep)
>> +{
>> + if (g->speed < USB_SPEED_SUPER ||
>> + !usb_endpoint_xfer_isoc(pep->endpoint.desc))
>> + return 0;
>> +
>> + return pep->endpoint.comp_desc->bmAttributes;
>> +}
>> +
>> +static u32 cdnsp_get_endpoint_max_burst(struct usb_gadget *g,
>> + struct cdnsp_ep *pep)
>> +{
>> + /* Super speed and Plus have max burst in ep companion desc */
>> + if (g->speed >= USB_SPEED_SUPER)
>> + return pep->endpoint.comp_desc->bMaxBurst;
>> +
>> + if (g->speed == USB_SPEED_HIGH &&
>> + (usb_endpoint_xfer_isoc(pep->endpoint.desc) ||
>> + usb_endpoint_xfer_int(pep->endpoint.desc)))
>> + return (usb_endpoint_maxp(pep->endpoint.desc) & 0x1800) >> 11;
>> +
>> + return 0;
>> +}
>> +
>> +static u32 cdnsp_get_endpoint_type(const struct usb_endpoint_descriptor *desc)
>> +{
>> + int in;
>> +
>> + in = usb_endpoint_dir_in(desc);
>> +
>> + switch (usb_endpoint_type(desc)) {
>> + case USB_ENDPOINT_XFER_CONTROL:
>> + return CTRL_EP;
>> + case USB_ENDPOINT_XFER_BULK:
>> + return in ? BULK_IN_EP : BULK_OUT_EP;
>> + case USB_ENDPOINT_XFER_ISOC:
>> + return in ? ISOC_IN_EP : ISOC_OUT_EP;
>> + case USB_ENDPOINT_XFER_INT:
>> + return in ? INT_IN_EP : INT_OUT_EP;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +/*
>> + * Return the maximum endpoint service interval time (ESIT) payload.
>> + * Basically, this is the maxpacket size, multiplied by the burst size
>> + * and mult size.
>> + */
>> +static u32 cdnsp_get_max_esit_payload(struct usb_gadget *g,
>> + struct cdnsp_ep *pep)
>> +{
>> + int max_packet;
>> + int max_burst;
>> +
>> + /* Only applies for interrupt or isochronous endpoints*/
>> + if (usb_endpoint_xfer_control(pep->endpoint.desc) ||
>> + usb_endpoint_xfer_bulk(pep->endpoint.desc))
>> + return 0;
>> +
>> + /* SuperSpeedPlus Isoc ep sending over 48k per EIST. */
>> + if (g->speed >= USB_SPEED_SUPER_PLUS &&
>> + USB_SS_SSP_ISOC_COMP(pep->endpoint.desc->bmAttributes))
>> + return le32_to_cpu(pep->endpoint.comp_desc->wBytesPerInterval);
>> + /* SuperSpeed or SuperSpeedPlus Isoc ep with less than 48k per esit */
>> + else if (g->speed >= USB_SPEED_SUPER)
>> + return le16_to_cpu(pep->endpoint.comp_desc->wBytesPerInterval);
>> +
>> + max_packet = usb_endpoint_maxp(pep->endpoint.desc);
>> + max_burst = usb_endpoint_maxp_mult(pep->endpoint.desc);
>> +
>> + /* A 0 in max burst means 1 transfer per ESIT */
>> + return max_packet * max_burst;
>> +}
>> +
>> +int cdnsp_endpoint_init(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep,
>> + gfp_t mem_flags)
>> +{
>> + enum cdnsp_ring_type ring_type;
>> + struct cdnsp_ep_ctx *ep_ctx;
>> + unsigned int err_count = 0;
>> + unsigned int avg_trb_len;
>> + unsigned int max_packet;
>> + unsigned int max_burst;
>> + unsigned int interval;
>> + u32 max_esit_payload;
>> + unsigned int mult;
>> + u32 endpoint_type;
>> + int ret;
>> +
>> + ep_ctx = pep->in_ctx;
>> +
>> + endpoint_type = cdnsp_get_endpoint_type(pep->endpoint.desc);
>> + if (!endpoint_type)
>> + return -EINVAL;
>> +
>> + ring_type = usb_endpoint_type(pep->endpoint.desc);
>> +
>> + /*
>> + * Get values to fill the endpoint context, mostly from ep descriptor.
>> + * The average TRB buffer length for bulk endpoints is unclear as we
>> + * have no clue on scatter gather list entry size. For Isoc and Int,
>> + * set it to max available.
>> + */
>> + max_esit_payload = cdnsp_get_max_esit_payload(&pdev->gadget, pep);
>> + interval = cdnsp_get_endpoint_interval(&pdev->gadget, pep);
>> + mult = cdnsp_get_endpoint_mult(&pdev->gadget, pep);
>> + max_packet = usb_endpoint_maxp(pep->endpoint.desc);
>> + max_burst = cdnsp_get_endpoint_max_burst(&pdev->gadget, pep);
>> + avg_trb_len = max_esit_payload;
>> +
>> + /* Allow 3 retries for everything but isoc, set CErr = 3. */
>> + if (!usb_endpoint_xfer_isoc(pep->endpoint.desc))
>> + err_count = 3;
>> + if (usb_endpoint_xfer_bulk(pep->endpoint.desc) &&
>> + pdev->gadget.speed == USB_SPEED_HIGH)
>> + max_packet = 512;
>> + /* Controller spec indicates that ctrl ep avg TRB Length should be 8. */
>> + if (usb_endpoint_xfer_control(pep->endpoint.desc))
>> + avg_trb_len = 8;
>> +
>> + /* Set up the endpoint ring. */
>> + pep->ring = cdnsp_ring_alloc(pdev, 2, ring_type, max_packet, mem_flags);
>> + pep->skip = false;
>> +
>> + /* Fill the endpoint context */
>> + ep_ctx->ep_info = cpu_to_le32(EP_MAX_ESIT_PAYLOAD_HI(max_esit_payload) |
>> + EP_INTERVAL(interval) | EP_MULT(mult));
>> + ep_ctx->ep_info2 = cpu_to_le32(EP_TYPE(endpoint_type) |
>> + MAX_PACKET(max_packet) | MAX_BURST(max_burst) |
>> + ERROR_COUNT(err_count));
>> + ep_ctx->deq = cpu_to_le64(pep->ring->first_seg->dma |
>> + pep->ring->cycle_state);
>> +
>> + ep_ctx->tx_info = cpu_to_le32(EP_MAX_ESIT_PAYLOAD_LO(max_esit_payload) |
>> + EP_AVG_TRB_LENGTH(avg_trb_len));
>> +
>> + if (usb_endpoint_xfer_bulk(pep->endpoint.desc) &&
>> + pdev->gadget.speed > USB_SPEED_HIGH) {
>> + ret = cdnsp_alloc_streams(pdev, pep);
>> + if (ret < 0)
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +void cdnsp_endpoint_zero(struct cdnsp_device *pdev, struct cdnsp_ep *pep)
>> +{
>> + pep->in_ctx->ep_info = 0;
>> + pep->in_ctx->ep_info2 = 0;
>> + pep->in_ctx->deq = 0;
>> + pep->in_ctx->tx_info = 0;
>> +}
>> +
>> +static int cdnsp_alloc_erst(struct cdnsp_device *pdev,
>> + struct cdnsp_ring *evt_ring,
>> + struct cdnsp_erst *erst,
>> + gfp_t flags)
>> +{
>> + struct cdnsp_erst_entry *entry;
>> + struct cdnsp_segment *seg;
>> + unsigned int val;
>> + size_t size;
>> +
>> + size = sizeof(struct cdnsp_erst_entry) * evt_ring->num_segs;
>> + erst->entries = dma_alloc_coherent(pdev->dev, size,
>> + &erst->erst_dma_addr, flags);
>> + if (!erst->entries)
>> + return -ENOMEM;
>> +
>> + erst->num_entries = evt_ring->num_segs;
>> +
>> + seg = evt_ring->first_seg;
>> + for (val = 0; val < evt_ring->num_segs; val++) {
>> + entry = &erst->entries[val];
>> + entry->seg_addr = cpu_to_le64(seg->dma);
>> + entry->seg_size = cpu_to_le32(TRBS_PER_SEGMENT);
>> + entry->rsvd = 0;
>> + seg = seg->next;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static void cdnsp_free_erst(struct cdnsp_device *pdev, struct cdnsp_erst *erst)
>> +{
>> + size_t size = sizeof(struct cdnsp_erst_entry) * (erst->num_entries);
>> + struct device *dev = pdev->dev;
>> +
>> + if (erst->entries)
>> + dma_free_coherent(dev, size, erst->entries,
>> + erst->erst_dma_addr);
>> +
>> + erst->entries = NULL;
>> +}
>> +
>> +void cdnsp_mem_cleanup(struct cdnsp_device *pdev)
>> +{
>> + struct device *dev = pdev->dev;
>> +
>> + cdnsp_free_priv_device(pdev);
>> + cdnsp_free_erst(pdev, &pdev->erst);
>> +
>> + if (pdev->event_ring)
>> + cdnsp_ring_free(pdev, pdev->event_ring);
>> +
>> + pdev->event_ring = NULL;
>> +
>> + if (pdev->cmd_ring)
>> + cdnsp_ring_free(pdev, pdev->cmd_ring);
>> +
>> + pdev->cmd_ring = NULL;
>> +
>> + dma_pool_destroy(pdev->segment_pool);
>> + pdev->segment_pool = NULL;
>> + dma_pool_destroy(pdev->device_pool);
>> + pdev->device_pool = NULL;
>> +
>> + if (pdev->dcbaa)
>> + dma_free_coherent(dev, sizeof(*pdev->dcbaa),
>> + pdev->dcbaa, pdev->dcbaa->dma);
>> +
>> + pdev->dcbaa = NULL;
>> +
>> + pdev->usb2_port.exist = 0;
>> + pdev->usb3_port.exist = 0;
>> + pdev->usb2_port.port_num = 0;
>> + pdev->usb3_port.port_num = 0;
>> + pdev->active_port = NULL;
>> +}
>> +
>> +static void cdnsp_set_event_deq(struct cdnsp_device *pdev)
>> +{
>> + dma_addr_t deq;
>> + u64 temp;
>> +
>> + deq = cdnsp_trb_virt_to_dma(pdev->event_ring->deq_seg,
>> + pdev->event_ring->dequeue);
>> +
>> + /* Update controller event ring dequeue pointer */
>> + temp = cdnsp_read_64(pdev, &pdev->ir_set->erst_dequeue);
>> + temp &= ERST_PTR_MASK;
>> +
>> + /*
>> + * Don't clear the EHB bit (which is RW1C) because
>> + * there might be more events to service.
>> + */
>> + temp &= ~ERST_EHB;
>> +
>> + cdnsp_write_64(pdev, ((u64)deq & (u64)~ERST_PTR_MASK) | temp,
>> + &pdev->ir_set->erst_dequeue);
>> +}
>> +
>> +static void cdnsp_add_in_port(struct cdnsp_device *pdev,
>> + struct cdnsp_port *port,
>> + __le32 __iomem *addr)
>> +{
>> + u32 temp, port_offset;
>> +
>> + temp = readl(addr);
>> + port->maj_rev = CDNSP_EXT_PORT_MAJOR(temp);
>> + port->min_rev = CDNSP_EXT_PORT_MINOR(temp);
>> +
>> + /* Port offset and count in the third dword.*/
>> + temp = readl(addr + 2);
>> + port_offset = CDNSP_EXT_PORT_OFF(temp);
>> +
>> + port->port_num = port_offset;
>> + port->exist = 1;
>> +}
>> +
>> +/*
>> + * Scan the Extended Capabilities for the "Supported Protocol Capabilities" that
>> + * specify what speeds each port is supposed to be.
>> + */
>> +static int cdnsp_setup_port_arrays(struct cdnsp_device *pdev, gfp_t flags)
>> +{
>> + void __iomem *base;
>> + u32 offset = 0;
>> + int i;
>> +
>> + base = &pdev->cap_regs->hc_capbase;
>> + offset = cdnsp_find_next_ext_cap(base, offset,
>> + EXT_CAP_CFG_DEV_20PORT_CAP_ID);
>> + pdev->port20_regs = base + offset;
>> +
>> + base = &pdev->cap_regs->hc_capbase;
>> + offset = cdnsp_find_next_ext_cap(base, offset, D_XEC_CFG_3XPORT_CAP);
>> + pdev->port3x_regs = base + offset;
>> +
>> + offset = 0;
>> + base = &pdev->cap_regs->hc_capbase;
>> +
>> + /* Driver expects max 2 extended protocol capability. */
>> + for (i = 0; i < 2; i++) {
>> + u32 temp;
>> +
>> + offset = cdnsp_find_next_ext_cap(base, offset,
>> + EXT_CAPS_PROTOCOL);
>> + temp = readl(base + offset);
>> +
>> + if (CDNSP_EXT_PORT_MAJOR(temp) == 0x03 &&
>> + !pdev->usb3_port.port_num)
>> + cdnsp_add_in_port(pdev, &pdev->usb3_port,
>> + base + offset);
>> +
>> + if (CDNSP_EXT_PORT_MAJOR(temp) == 0x02 &&
>> + !pdev->usb2_port.port_num)
>> + cdnsp_add_in_port(pdev, &pdev->usb2_port,
>> + base + offset);
>> + }
>> +
>> + if (!pdev->usb2_port.exist || !pdev->usb3_port.exist) {
>> + dev_err(pdev->dev, "Error: Only one port detected\n");
>> + return -ENODEV;
>> + }
>> +
>> + pdev->usb2_port.regs = (struct cdnsp_port_regs *)
>> + (&pdev->op_regs->port_reg_base + NUM_PORT_REGS *
>> + (pdev->usb2_port.port_num - 1));
>> +
>> + pdev->usb3_port.regs = (struct cdnsp_port_regs *)
>> + (&pdev->op_regs->port_reg_base + NUM_PORT_REGS *
>> + (pdev->usb3_port.port_num - 1));
>> +
>> + return 0;
>> +}
>> +
>> +/*
>> + * Initialize memory for CDNSP (one-time init).
>> + *
>> + * Program the PAGESIZE register, initialize the device context array, create
>> + * device contexts, set up a command ring segment, create event
>> + * ring (one for now).
>> + */
>> +int cdnsp_mem_init(struct cdnsp_device *pdev, gfp_t flags)
>> +{
>> + struct device *dev = pdev->dev;
>> + int ret = -ENOMEM;
>> + unsigned int val;
>> + dma_addr_t dma;
>> + u32 page_size;
>> + u64 val_64;
>> +
>> + /*
>> + * Use 4K pages, since that's common and the minimum the
>> + * controller supports
>> + */
>> + page_size = 1 << 12;
>> +
>> + val = readl(&pdev->op_regs->config_reg);
>> + val |= ((val & ~MAX_DEVS) | CDNSP_DEV_MAX_SLOTS) | CONFIG_U3E;
>> + writel(val, &pdev->op_regs->config_reg);
>> +
>> + /*
>> + * Doorbell array must be physically contiguous
>> + * and 64-byte (cache line) aligned.
>> + */
>> + pdev->dcbaa = dma_alloc_coherent(dev, sizeof(*pdev->dcbaa),
>> + &dma, GFP_KERNEL);
>> + if (!pdev->dcbaa)
>> + goto mem_init_fail;
>> +
>> + memset(pdev->dcbaa, 0, sizeof(*pdev->dcbaa));
>> + pdev->dcbaa->dma = dma;
>> +
>> + cdnsp_write_64(pdev, dma, &pdev->op_regs->dcbaa_ptr);
>> +
>> + /*
>> + * Initialize the ring segment pool. The ring must be a contiguous
>> + * structure comprised of TRBs. The TRBs must be 16 byte aligned,
>> + * however, the command ring segment needs 64-byte aligned segments
>> + * and our use of dma addresses in the trb_address_map radix tree needs
>> + * TRB_SEGMENT_SIZE alignment, so driver pick the greater alignment
>> + * need.
>> + */
>> + pdev->segment_pool = dma_pool_create("CDNSP ring segments", dev,
>> + TRB_SEGMENT_SIZE, TRB_SEGMENT_SIZE,
>> + page_size);
>> +
>> + pdev->device_pool = dma_pool_create("CDNSP input/output contexts", dev,
>> + CDNSP_CTX_SIZE, 64, page_size);
>> +
>> + if (!pdev->segment_pool || !pdev->device_pool)
>> + goto mem_init_fail;
>> +
>> + /* Set up the command ring to have one segments for now. */
>> + pdev->cmd_ring = cdnsp_ring_alloc(pdev, 1, TYPE_COMMAND, 0, flags);
>> + if (!pdev->cmd_ring)
>> + goto mem_init_fail;
>> +
>> + /* Set the address in the Command Ring Control register */
>> + val_64 = cdnsp_read_64(pdev, &pdev->op_regs->cmd_ring);
>> + val_64 = (val_64 & (u64)CMD_RING_RSVD_BITS) |
>> + (pdev->cmd_ring->first_seg->dma & (u64)~CMD_RING_RSVD_BITS) |
>> + pdev->cmd_ring->cycle_state;
>> + cdnsp_write_64(pdev, val_64, &pdev->op_regs->cmd_ring);
>> +
>> + val = readl(&pdev->cap_regs->db_off);
>> + val &= DBOFF_MASK;
>> + pdev->dba = (void __iomem *)pdev->cap_regs + val;
>> +
>> + /* Set ir_set to interrupt register set 0 */
>> + pdev->ir_set = &pdev->run_regs->ir_set[0];
>> +
>> + /*
>> + * Event ring setup: Allocate a normal ring, but also setup
>> + * the event ring segment table (ERST).
>> + */
>> + pdev->event_ring = cdnsp_ring_alloc(pdev, ERST_NUM_SEGS, TYPE_EVENT,
>> + 0, flags);
>> + if (!pdev->event_ring)
>> + goto mem_init_fail;
>> +
>> + ret = cdnsp_alloc_erst(pdev, pdev->event_ring, &pdev->erst, flags);
>> + if (ret)
>> + goto mem_init_fail;
>> +
>> + /* Set ERST count with the number of entries in the segment table. */
>> + val = readl(&pdev->ir_set->erst_size);
>> + val &= ERST_SIZE_MASK;
>> + val |= ERST_NUM_SEGS;
>> + writel(val, &pdev->ir_set->erst_size);
>> +
>> + /* Set the segment table base address. */
>> + val_64 = cdnsp_read_64(pdev, &pdev->ir_set->erst_base);
>> + val_64 &= ERST_PTR_MASK;
>> + val_64 |= (pdev->erst.erst_dma_addr & (u64)~ERST_PTR_MASK);
>> + cdnsp_write_64(pdev, val_64, &pdev->ir_set->erst_base);
>> +
>> + /* Set the event ring dequeue address. */
>> + cdnsp_set_event_deq(pdev);
>> +
>> + ret = cdnsp_setup_port_arrays(pdev, flags);
>> + if (ret)
>> + goto mem_init_fail;
>> +
>> + ret = cdnsp_alloc_priv_device(pdev, GFP_ATOMIC);
>> + if (ret) {
>> + dev_err(pdev->dev,
>> + "Could not allocate cdnsp_device data structures\n");
>> + goto mem_init_fail;
>> + }
>> +
>> + return 0;
>> +
>> +mem_init_fail:
>> + dev_err(pdev->dev, "Couldn't initialize memory\n");
>> + cdnsp_halt(pdev);
>> + cdnsp_reset(pdev);
>> + cdnsp_mem_cleanup(pdev);
>> +
>> + return ret;
>> +}
>> +
>> diff --git a/drivers/usb/cdnsp/ring.c b/drivers/usb/cdnsp/ring.c
>> new file mode 100644
>> index 000000000000..b7fdfbbebcc0
>> --- /dev/null
>> +++ b/drivers/usb/cdnsp/ring.c
>> @@ -0,0 +1,2363 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Cadence CDNSP DRD Driver.
>> + *
>> + * Copyright (C) 2020 Cadence.
>> + *
>> + * Author: Pawel Laszczak <[email protected]>
>> + *
>> + * Code based on Linux XHCI driver.
>> + * Origin: Copyright (C) 2008 Intel Corp
>> + */
>> +
>> +/*
>> + * Ring initialization rules:
>> + * 1. Each segment is initialized to zero, except for link TRBs.
>> + * 2. Ring cycle state = 0. This represents Producer Cycle State (PCS) or
>> + * Consumer Cycle State (CCS), depending on ring function.
>> + * 3. Enqueue pointer = dequeue pointer = address of first TRB in the segment.
>> + *
>> + * Ring behavior rules:
>> + * 1. A ring is empty if enqueue == dequeue. This means there will always be at
>> + * least one free TRB in the ring. This is useful if you want to turn that
>> + * into a link TRB and expand the ring.
>> + * 2. When incrementing an enqueue or dequeue pointer, if the next TRB is a
>> + * link TRB, then load the pointer with the address in the link TRB. If the
>> + * link TRB had its toggle bit set, you may need to update the ring cycle
>> + * state (see cycle bit rules). You may have to do this multiple times
>> + * until you reach a non-link TRB.
>> + * 3. A ring is full if enqueue++ (for the definition of increment above)
>> + * equals the dequeue pointer.
>> + *
>> + * Cycle bit rules:
>> + * 1. When a consumer increments a dequeue pointer and encounters a toggle bit
>> + * in a link TRB, it must toggle the ring cycle state.
>> + * 2. When a producer increments an enqueue pointer and encounters a toggle bit
>> + * in a link TRB, it must toggle the ring cycle state.
>> + *
>> + * Producer rules:
>> + * 1. Check if ring is full before you enqueue.
>> + * 2. Write the ring cycle state to the cycle bit in the TRB you're enqueuing.
>> + * Update enqueue pointer between each write (which may update the ring
>> + * cycle state).
>> + * 3. Notify consumer. If SW is producer, it rings the doorbell for command
>> + * and endpoint rings. If controller is the producer for the event ring,
>> + * and it generates an interrupt according to interrupt modulation rules.
>> + *
>> + * Consumer rules:
>> + * 1. Check if TRB belongs to you. If the cycle bit == your ring cycle state,
>> + * the TRB is owned by the consumer.
>> + * 2. Update dequeue pointer (which may update the ring cycle state) and
>> + * continue processing TRBs until you reach a TRB which is not owned by you.
>> + * 3. Notify the producer. SW is the consumer for the event ring, and it
>> + * updates event ring dequeue pointer. Controller is the consumer for the
>> + * command and endpoint rings; it generates events on the event ring
>> + * for these.
>> + */
>> +
>> +#include <linux/scatterlist.h>
>> +#include <linux/dma-mapping.h>
>> +#include <linux/delay.h>
>> +#include <linux/slab.h>
>> +#include <linux/irq.h>
>> +
>> +#include "gadget.h"
>> +
>> +/*
>> + * Returns zero if the TRB isn't in this segment, otherwise it returns the DMA
>> + * address of the TRB.
>> + */
>> +dma_addr_t cdnsp_trb_virt_to_dma(struct cdnsp_segment *seg,
>> + union cdnsp_trb *trb)
>> +{
>> + unsigned long segment_offset = trb - seg->trbs;
>> +
>> + if (trb < seg->trbs || segment_offset >= TRBS_PER_SEGMENT)
>> + return 0;
>> +
>> + return seg->dma + (segment_offset * sizeof(*trb));
>> +}
>> +
>> +static bool cdnsp_trb_is_noop(union cdnsp_trb *trb)
>> +{
>> + return TRB_TYPE_NOOP_LE32(trb->generic.field[3]);
>> +}
>> +
>> +static bool cdnsp_trb_is_link(union cdnsp_trb *trb)
>> +{
>> + return TRB_TYPE_LINK_LE32(trb->link.control);
>> +}
>> +
>> +bool cdnsp_last_trb_on_seg(struct cdnsp_segment *seg, union cdnsp_trb *trb)
>> +{
>> + return trb == &seg->trbs[TRBS_PER_SEGMENT - 1];
>> +}
>> +
>> +bool cdnsp_last_trb_on_ring(struct cdnsp_ring *ring,
>> + struct cdnsp_segment *seg,
>> + union cdnsp_trb *trb)
>> +{
>> + return cdnsp_last_trb_on_seg(seg, trb) && (seg->next == ring->first_seg);
>> +}
>> +
>> +static bool cdnsp_link_trb_toggles_cycle(union cdnsp_trb *trb)
>> +{
>> + return le32_to_cpu(trb->link.control) & LINK_TOGGLE;
>> +}
>> +
>> +static void cdnsp_trb_to_noop(union cdnsp_trb *trb, u32 noop_type)
>> +{
>> + if (cdnsp_trb_is_link(trb)) {
>> + /* Unchain chained link TRBs. */
>> + trb->link.control &= cpu_to_le32(~TRB_CHAIN);
>> + } else {
>> + trb->generic.field[0] = 0;
>> + trb->generic.field[1] = 0;
>> + trb->generic.field[2] = 0;
>> + /* Preserve only the cycle bit of this TRB. */
>> + trb->generic.field[3] &= cpu_to_le32(TRB_CYCLE);
>> + trb->generic.field[3] |= cpu_to_le32(TRB_TYPE(noop_type));
>> + }
>> +}
>> +
>> +/*
>> + * Updates trb to point to the next TRB in the ring, and updates seg if the next
>> + * TRB is in a new segment. This does not skip over link TRBs, and it does not
>> + * effect the ring dequeue or enqueue pointers.
>> + */
>> +static void cdnsp_next_trb(struct cdnsp_device *pdev,
>> + struct cdnsp_ring *ring,
>> + struct cdnsp_segment **seg,
>> + union cdnsp_trb **trb)
>> +{
>> + if (cdnsp_trb_is_link(*trb)) {
>> + *seg = (*seg)->next;
>> + *trb = ((*seg)->trbs);
>> + } else {
>> + (*trb)++;
>> + }
>> +}
>> +
>> +/*
>> + * See Cycle bit rules. SW is the consumer for the event ring only.
>> + * Don't make a ring full of link TRBs. That would be dumb and this would loop.
>> + */
>> +void cdnsp_inc_deq(struct cdnsp_device *pdev, struct cdnsp_ring *ring)
>> +{
>> + /* event ring doesn't have link trbs, check for last trb. */
>> + if (ring->type == TYPE_EVENT) {
>> + if (!cdnsp_last_trb_on_seg(ring->deq_seg, ring->dequeue)) {
>> + ring->dequeue++;
>> + return;
>> + }
>> +
>> + if (cdnsp_last_trb_on_ring(ring, ring->deq_seg, ring->dequeue))
>> + ring->cycle_state ^= 1;
>> +
>> + ring->deq_seg = ring->deq_seg->next;
>> + ring->dequeue = ring->deq_seg->trbs;
>> + return;
>> + }
>> +
>> + /* All other rings have link trbs. */
>> + if (!cdnsp_trb_is_link(ring->dequeue)) {
>> + ring->dequeue++;
>> + ring->num_trbs_free++;
>> + }
>> + while (cdnsp_trb_is_link(ring->dequeue)) {
>> + ring->deq_seg = ring->deq_seg->next;
>> + ring->dequeue = ring->deq_seg->trbs;
>> + }
>> +}
>> +
>> +/*
>> + * See Cycle bit rules. SW is the consumer for the event ring only.
>> + * Don't make a ring full of link TRBs. That would be dumb and this would loop.
>> + *
>> + * If we've just enqueued a TRB that is in the middle of a TD (meaning the
>> + * chain bit is set), then set the chain bit in all the following link TRBs.
>> + * If we've enqueued the last TRB in a TD, make sure the following link TRBs
>> + * have their chain bit cleared (so that each Link TRB is a separate TD).
>> + *
>> + * @more_trbs_coming: Will you enqueue more TRBs before ringing the doorbell.
>> + */
>> +static void cdnsp_inc_enq(struct cdnsp_device *pdev,
>> + struct cdnsp_ring *ring,
>> + bool more_trbs_coming)
>> +{
>> + union cdnsp_trb *next;
>> + u32 chain;
>> +
>> + chain = le32_to_cpu(ring->enqueue->generic.field[3]) & TRB_CHAIN;
>> +
>> + /* If this is not event ring, there is one less usable TRB. */
>> + if (!cdnsp_trb_is_link(ring->enqueue))
>> + ring->num_trbs_free--;
>> + next = ++(ring->enqueue);
>> +
>> + /* Update the dequeue pointer further if that was a link TRB */
>> + while (cdnsp_trb_is_link(next)) {
>> + /*
>> + * If the caller doesn't plan on enqueuing more TDs before
>> + * ringing the doorbell, then we don't want to give the link TRB
>> + * to the hardware just yet. We'll give the link TRB back in
>> + * cdnsp_prepare_ring() just before we enqueue the TD at the
>> + * top of the ring.
>> + */
>> + if (!chain && !more_trbs_coming)
>> + break;
>> +
>> + next->link.control &= cpu_to_le32(~TRB_CHAIN);
>> + next->link.control |= cpu_to_le32(chain);
>> +
>> + /* Give this link TRB to the hardware */
>> + wmb();
>> + next->link.control ^= cpu_to_le32(TRB_CYCLE);
>> +
>> + /* Toggle the cycle bit after the last ring segment. */
>> + if (cdnsp_link_trb_toggles_cycle(next))
>> + ring->cycle_state ^= 1;
>> +
>> + ring->enq_seg = ring->enq_seg->next;
>> + ring->enqueue = ring->enq_seg->trbs;
>> + next = ring->enqueue;
>> + }
>> +}
>> +
>> +/*
>> + * Check to see if there's room to enqueue num_trbs on the ring and make sure
>> + * enqueue pointer will not advance into dequeue segment.
>> + */
>> +static bool cdnsp_room_on_ring(struct cdnsp_device *pdev,
>> + struct cdnsp_ring *ring,
>> + unsigned int num_trbs)
>> +{
>> + int num_trbs_in_deq_seg;
>> +
>> + if (ring->num_trbs_free < num_trbs)
>> + return false;
>> +
>> + if (ring->type != TYPE_COMMAND && ring->type != TYPE_EVENT) {
>> + num_trbs_in_deq_seg = ring->dequeue - ring->deq_seg->trbs;
>> +
>> + if (ring->num_trbs_free < num_trbs + num_trbs_in_deq_seg)
>> + return false;
>> + }
>> +
>> + return true;
>> +}
>> +
>> +/* Ring the doorbell after placing a command on the ring. */
>> +void cdnsp_ring_cmd_db(struct cdnsp_device *pdev)
>> +{
>> + writel(DB_VALUE_CMD, &pdev->dba->cmd_db);
>> +}
>> +
>> +/*
>> + * Ring the doorbell after placing a transfer on the ring.
>> + * Returns true if doorbell was set, otherwise false.
>> + */
>> +static bool cdnsp_ring_ep_doorbell(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep,
>> + unsigned int stream_id)
>> +{
>> + __le32 __iomem *reg_addr = &pdev->dba->ep_db;
>> + unsigned int ep_state = pep->ep_state;
>> + unsigned int db_value;
>> +
>> + /*
>> + * Don't ring the doorbell for this endpoint if endpoint is halted or
>> + * disabled.
>> + */
>> + if (ep_state & EP_HALTED || !(ep_state & EP_ENABLED))
>> + return false;
>> +
>> + /* For stream capable endpoints driver can ring doorbell only twice. */
>> + if (pep->ep_state & EP_HAS_STREAMS) {
>> + if (pep->stream_info.drbls_count >= 2)
>> + return false;
>> +
>> + pep->stream_info.drbls_count++;
>> + }
>> +
>> + pep->ep_state &= ~EP_STOPPED;
>> +
>> + if (pep->idx == 0 && pdev->ep0_stage == CDNSP_DATA_STAGE &&
>> + !pdev->ep0_expect_in)
>> + db_value = DB_VALUE_EP0_OUT(pep->idx, stream_id);
>> + else
>> + db_value = DB_VALUE(pep->idx, stream_id);
>> +
>> + writel(db_value, reg_addr);
>> +
>> + /* Doorbell was set. */
>> + return true;
>> +}
>> +
>> +/*
>> + * Get the right ring for the given pep and stream_id.
>> + * If the endpoint supports streams, boundary check the USB request's stream ID.
>> + * If the endpoint doesn't support streams, return the singular endpoint ring.
>> + */
>> +static struct cdnsp_ring *cdnsp_get_transfer_ring(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep,
>> + unsigned int stream_id)
>> +{
>> + if (!(pep->ep_state & EP_HAS_STREAMS))
>> + return pep->ring;
>> +
>> + if (stream_id == 0 || stream_id >= pep->stream_info.num_streams) {
>> + dev_err(pdev->dev, "ERR: %s ring doesn't exist for SID: %d.\n",
>> + pep->name, stream_id);
>> + return NULL;
>> + }
>> +
>> + return pep->stream_info.stream_rings[stream_id];
>> +}
>> +
>> +static struct cdnsp_ring *
>> + cdnsp_request_to_transfer_ring(struct cdnsp_device *pdev,
>> + struct cdnsp_request *preq)
>> +{
>> + return cdnsp_get_transfer_ring(pdev, preq->pep,
>> + preq->request.stream_id);
>> +}
>> +
>> +/* Ring the doorbell for any rings with pending requests. */
>> +void cdnsp_ring_doorbell_for_active_rings(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep)
>> +{
>> + struct cdnsp_stream_info *stream_info;
>> + unsigned int stream_id;
>> + int ret;
>> +
>> + if (pep->ep_state & EP_DIS_IN_RROGRESS)
>> + return;
>> +
>> + /* A ring has pending Request if its TD list is not empty. */
>> + if (!(pep->ep_state & EP_HAS_STREAMS) && pep->number) {
>> + if (pep->ring && !list_empty(&pep->ring->td_list))
>> + cdnsp_ring_ep_doorbell(pdev, pep, 0);
>> + return;
>> + }
>> +
>> + stream_info = &pep->stream_info;
>> +
>> + for (stream_id = 1; stream_id < stream_info->num_streams; stream_id++) {
>> + struct cdnsp_td *td, *td_temp;
>> + struct cdnsp_ring *ep_ring;
>> +
>> + if (stream_info->drbls_count >= 2)
>> + return;
>> +
>> + ep_ring = cdnsp_get_transfer_ring(pdev, pep, stream_id);
>> + if (!ep_ring)
>> + continue;
>> +
>> + if (!ep_ring->stream_active || ep_ring->stream_rejected)
>> + continue;
>> +
>> + list_for_each_entry_safe(td, td_temp, &ep_ring->td_list,
>> + td_list) {
>> + if (td->drbl)
>> + continue;
>> +
>> + ret = cdnsp_ring_ep_doorbell(pdev, pep, stream_id);
>> + if (ret)
>> + td->drbl = 1;
>> + }
>> + }
>> +}
>> +
>> +/*
>> + * Get the hw dequeue pointer controller stopped on, either directly from the
>> + * endpoint context, or if streams are in use from the stream context.
>> + * The returned hw_dequeue contains the lowest four bits with cycle state
>> + * and possible stream context type.
>> + */
>> +static u64 cdnsp_get_hw_deq(struct cdnsp_device *pdev,
>> + unsigned int ep_index,
>> + unsigned int stream_id)
>> +{
>> + struct cdnsp_stream_ctx *st_ctx;
>> + struct cdnsp_ep *pep;
>> +
>> + pep = &pdev->eps[stream_id];
>> +
>> + if (pep->ep_state & EP_HAS_STREAMS) {
>> + st_ctx = &pep->stream_info.stream_ctx_array[stream_id];
>> + return le64_to_cpu(st_ctx->stream_ring);
>> + }
>> +
>> + return le64_to_cpu(pep->out_ctx->deq);
>> +}
>> +
>> +/*
>> + * Move the controller endpoint ring dequeue pointer past cur_td.
>> + * Record the new state of the controller endpoint ring dequeue segment,
>> + * dequeue pointer, and new consumer cycle state in state.
>> + * Update internal representation of the ring's dequeue pointer.
>> + *
>> + * We do this in three jumps:
>> + * - First we update our new ring state to be the same as when the
>> + * controller stopped.
>> + * - Then we traverse the ring to find the segment that contains
>> + * the last TRB in the TD. We toggle the controller new cycle state
>> + * when we pass any link TRBs with the toggle cycle bit set.
>> + * - Finally we move the dequeue state one TRB further, toggling the cycle bit
>> + * if we've moved it past a link TRB with the toggle cycle bit set.
>> + */
>> +static void cdnsp_find_new_dequeue_state(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep,
>> + unsigned int stream_id,
>> + struct cdnsp_td *cur_td,
>> + struct cdnsp_dequeue_state *state)
>> +{
>> + bool td_last_trb_found = false;
>> + struct cdnsp_segment *new_seg;
>> + struct cdnsp_ring *ep_ring;
>> + union cdnsp_trb *new_deq;
>> + bool cycle_found = false;
>> + u64 hw_dequeue;
>> +
>> + ep_ring = cdnsp_get_transfer_ring(pdev, pep, stream_id);
>> + if (!ep_ring)
>> + return;
>> +
>> + /*
>> + * Dig out the cycle state saved by the controller during the
>> + * stop endpoint command.
>> + */
>> + hw_dequeue = cdnsp_get_hw_deq(pdev, pep->idx, stream_id);
>> + new_seg = ep_ring->deq_seg;
>> + new_deq = ep_ring->dequeue;
>> + state->new_cycle_state = hw_dequeue & 0x1;
>> + state->stream_id = stream_id;
>> +
>> + /*
>> + * We want to find the pointer, segment and cycle state of the new trb
>> + * (the one after current TD's last_trb). We know the cycle state at
>> + * hw_dequeue, so walk the ring until both hw_dequeue and last_trb are
>> + * found.
>> + */
>> + do {
>> + if (!cycle_found && cdnsp_trb_virt_to_dma(new_seg, new_deq)
>> + == (dma_addr_t)(hw_dequeue & ~0xf)) {
>> + cycle_found = true;
>> +
>> + if (td_last_trb_found)
>> + break;
>> + }
>> +
>> + if (new_deq == cur_td->last_trb)
>> + td_last_trb_found = true;
>> +
>> + if (cycle_found && cdnsp_trb_is_link(new_deq) &&
>> + cdnsp_link_trb_toggles_cycle(new_deq))
>> + state->new_cycle_state ^= 0x1;
>> +
>> + cdnsp_next_trb(pdev, ep_ring, &new_seg, &new_deq);
>> +
>> + /* Search wrapped around, bail out. */
>> + if (new_deq == pep->ring->dequeue) {
>> + dev_err(pdev->dev,
>> + "Error: Failed finding new dequeue state\n");
>> + state->new_deq_seg = NULL;
>> + state->new_deq_ptr = NULL;
>> + return;
>> + }
>> +
>> + } while (!cycle_found || !td_last_trb_found);
>> +
>> + state->new_deq_seg = new_seg;
>> + state->new_deq_ptr = new_deq;
>> +}
>> +
>> +/*
>> + * flip_cycle means flip the cycle bit of all but the first and last TRB.
>> + * (The last TRB actually points to the ring enqueue pointer, which is not part
>> + * of this TD.) This is used to remove partially enqueued isoc TDs from a ring.
>> + */
>> +static void cdnsp_td_to_noop(struct cdnsp_device *pdev,
>> + struct cdnsp_ring *ep_ring,
>> + struct cdnsp_td *td,
>> + bool flip_cycle)
>> +{
>> + struct cdnsp_segment *seg = td->start_seg;
>> + union cdnsp_trb *trb = td->first_trb;
>> +
>> + while (1) {
>> + cdnsp_trb_to_noop(trb, TRB_TR_NOOP);
>> +
>> + /* flip cycle if asked to */
>> + if (flip_cycle && trb != td->first_trb && trb != td->last_trb)
>> + trb->generic.field[3] ^= cpu_to_le32(TRB_CYCLE);
>> +
>> + if (trb == td->last_trb)
>> + break;
>> +
>> + cdnsp_next_trb(pdev, ep_ring, &seg, &trb);
>> + }
>> +}
>> +
>> +/*
>> + * This TD is defined by the TRBs starting at start_trb in start_seg and ending
>> + * at end_trb, which may be in another segment. If the suspect DMA address is a
>> + * TRB in this TD, this function returns that TRB's segment. Otherwise it
>> + * returns 0.
>> + */
>> +static struct cdnsp_segment *cdnsp_trb_in_td(struct cdnsp_device *pdev,
>> + struct cdnsp_segment *start_seg,
>> + union cdnsp_trb *start_trb,
>> + union cdnsp_trb *end_trb,
>> + dma_addr_t suspect_dma)
>> +{
>> + struct cdnsp_segment *cur_seg;
>> + union cdnsp_trb *temp_trb;
>> + dma_addr_t end_seg_dma;
>> + dma_addr_t end_trb_dma;
>> + dma_addr_t start_dma;
>> +
>> + start_dma = cdnsp_trb_virt_to_dma(start_seg, start_trb);
>> + cur_seg = start_seg;
>> +
>> + do {
>> + if (start_dma == 0)
>> + return NULL;
>> +
>> + temp_trb = &cur_seg->trbs[TRBS_PER_SEGMENT - 1];
>> + /* We may get an event for a Link TRB in the middle of a TD */
>> + end_seg_dma = cdnsp_trb_virt_to_dma(cur_seg, temp_trb);
>> + /* If the end TRB isn't in this segment, this is set to 0 */
>> + end_trb_dma = cdnsp_trb_virt_to_dma(cur_seg, end_trb);
>> +
>> + if (end_trb_dma > 0) {
>> + /*
>> + * The end TRB is in this segment, so suspect should
>> + * be here
>> + */
>> + if (start_dma <= end_trb_dma) {
>> + if (suspect_dma >= start_dma &&
>> + suspect_dma <= end_trb_dma) {
>> + return cur_seg;
>> + }
>> + } else {
>> + /*
>> + * Case for one segment with a
>> + * TD wrapped around to the top
>> + */
>> + if ((suspect_dma >= start_dma &&
>> + suspect_dma <= end_seg_dma) ||
>> + (suspect_dma >= cur_seg->dma &&
>> + suspect_dma <= end_trb_dma)) {
>> + return cur_seg;
>> + }
>> + }
>> +
>> + return NULL;
>> + }
>> +
>> + /* Might still be somewhere in this segment */
>> + if (suspect_dma >= start_dma && suspect_dma <= end_seg_dma)
>> + return cur_seg;
>> +
>> + cur_seg = cur_seg->next;
>> + start_dma = cdnsp_trb_virt_to_dma(cur_seg, &cur_seg->trbs[0]);
>> + } while (cur_seg != start_seg);
>> +
>> + return NULL;
>> +}
>> +
>> +static void cdnsp_unmap_td_bounce_buffer(struct cdnsp_device *pdev,
>> + struct cdnsp_ring *ring,
>> + struct cdnsp_td *td)
>> +{
>> + struct cdnsp_segment *seg = td->bounce_seg;
>> + struct cdnsp_request *preq;
>> + size_t len;
>> +
>> + if (!seg)
>> + return;
>> +
>> + preq = td->preq;
>> +
>> + if (!preq->direction) {
>> + dma_unmap_single(pdev->dev, seg->bounce_dma,
>> + ring->bounce_buf_len, DMA_TO_DEVICE);
>> + return;
>> + }
>> +
>> + dma_unmap_single(pdev->dev, seg->bounce_dma, ring->bounce_buf_len,
>> + DMA_FROM_DEVICE);
>> +
>> + /* For in transfers we need to copy the data from bounce to sg */
>> + len = sg_pcopy_from_buffer(preq->request.sg, preq->request.num_sgs,
>> + seg->bounce_buf, seg->bounce_len,
>> + seg->bounce_offs);
>> + if (len != seg->bounce_len)
>> + dev_warn(pdev->dev, "WARN Wrong bounce buffer read length: %zu != %d\n",
>> + len, seg->bounce_len);
>> +
>> + seg->bounce_len = 0;
>> + seg->bounce_offs = 0;
>> +}
>> +
>> +static int cdnsp_cmd_set_deq(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep,
>> + struct cdnsp_dequeue_state *deq_state)
>> +{
>> + struct cdnsp_ring *ep_ring;
>> + int ret;
>> +
>> + if (!deq_state->new_deq_ptr || !deq_state->new_deq_seg) {
>> + cdnsp_ring_doorbell_for_active_rings(pdev, pep);
>> + return 0;
>> + }
>> +
>> + cdnsp_queue_new_dequeue_state(pdev, pep, deq_state);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> +
>> + /*
>> + * Update the ring's dequeue segment and dequeue pointer
>> + * to reflect the new position.
>> + */
>> + ep_ring = cdnsp_get_transfer_ring(pdev, pep, deq_state->stream_id);
>> +
>> + if (cdnsp_trb_is_link(ep_ring->dequeue)) {
>> + ep_ring->deq_seg = ep_ring->deq_seg->next;
>> + ep_ring->dequeue = ep_ring->deq_seg->trbs;
>> + }
>> +
>> + while (ep_ring->dequeue != deq_state->new_deq_ptr) {
>> + ep_ring->num_trbs_free++;
>> + ep_ring->dequeue++;
>> +
>> + if (cdnsp_trb_is_link(ep_ring->dequeue)) {
>> + if (ep_ring->dequeue == deq_state->new_deq_ptr)
>> + break;
>> +
>> + ep_ring->deq_seg = ep_ring->deq_seg->next;
>> + ep_ring->dequeue = ep_ring->deq_seg->trbs;
>> + }
>> + }
>> +
>> + /*
>> + * Probably there was TIMEOUT during handling Set Dequeue Pointer
>> + * command. It's critical error and controller will be stopped.
>> + */
>> + if (ret)
>> + return -ESHUTDOWN;
>> +
>> + /* Restart any rings with pending requests */
>> + cdnsp_ring_doorbell_for_active_rings(pdev, pep);
>> +
>> + return 0;
>> +}
>> +
>> +int cdnsp_remove_request(struct cdnsp_device *pdev,
>> + struct cdnsp_request *preq,
>> + struct cdnsp_ep *pep)
>> +{
>> + struct cdnsp_dequeue_state deq_state;
>> + struct cdnsp_td *cur_td = NULL;
>> + struct cdnsp_ring *ep_ring;
>> + struct cdnsp_segment *seg;
>> + int status = -ECONNRESET;
>> + int ret = 0;
>> + u64 hw_deq;
>> +
>> + memset(&deq_state, 0, sizeof(deq_state));
>> +
>> + cur_td = &preq->td;
>> + ep_ring = cdnsp_request_to_transfer_ring(pdev, preq);
>> +
>> + /*
>> + * If we stopped on the TD we need to cancel, then we have to
>> + * move the controller endpoint ring dequeue pointer past
>> + * this TD.
>> + */
>> + hw_deq = cdnsp_get_hw_deq(pdev, pep->idx, preq->request.stream_id);
>> + hw_deq &= ~0xf;
>> +
>> + seg = cdnsp_trb_in_td(pdev, cur_td->start_seg, cur_td->first_trb,
>> + cur_td->last_trb, hw_deq);
>> +
>> + if (seg && (pep->ep_state & EP_ENABLED))
>> + cdnsp_find_new_dequeue_state(pdev, pep, preq->request.stream_id,
>> + cur_td, &deq_state);
>> + else
>> + cdnsp_td_to_noop(pdev, ep_ring, cur_td, false);
>> +
>> + /*
>> + * The event handler won't see a completion for this TD anymore,
>> + * so remove it from the endpoint ring's TD list.
>> + */
>> + list_del_init(&cur_td->td_list);
>> + ep_ring->num_tds--;
>> + pep->stream_info.td_count--;
>> +
>> + /*
>> + * During disconnecting all endpoint will be disabled so we don't
>> + * have to worry about updating dequeue pointer.
>> + */
>> + if (pdev->cdnsp_state & CDNSP_STATE_DISCONNECT_PENDING) {
>> + status = -ESHUTDOWN;
>> + ret = cdnsp_cmd_set_deq(pdev, pep, &deq_state);
>> + }
>> +
>> + cdnsp_unmap_td_bounce_buffer(pdev, ep_ring, cur_td);
>> + cdnsp_gadget_giveback(pep, cur_td->preq, status);
>> +
>> + return ret;
>> +}
>> +
>> +static int cdnsp_update_port_id(struct cdnsp_device *pdev, u32 port_id)
>> +{
>> + struct cdnsp_port *port = pdev->active_port;
>> + u8 old_port = 0;
>> +
>> + if (port && port->port_num == port_id)
>> + return 0;
>> +
>> + if (port)
>> + old_port = port->port_num;
>> +
>> + if (port_id == pdev->usb2_port.port_num) {
>> + port = &pdev->usb2_port;
>> + } else if (port_id == pdev->usb3_port.port_num) {
>> + port = &pdev->usb3_port;
>> + } else {
>> + dev_err(pdev->dev, "Port event with invalid port ID %d\n",
>> + port_id);
>> + return -EINVAL;
>> + }
>> +
>> + if (port_id != old_port) {
>> + cdnsp_disable_slot(pdev);
>> + pdev->active_port = port;
>> + cdnsp_enable_slot(pdev);
>> + }
>> +
>> + if (port_id == pdev->usb2_port.port_num)
>> + cdnsp_set_usb2_hardware_lpm(pdev, NULL, 1);
>> + else
>> + writel(PORT_U1_TIMEOUT(1) | PORT_U2_TIMEOUT(1),
>> + &pdev->usb3_port.regs->portpmsc);
>> +
>> + return 0;
>> +}
>> +
>> +static void cdnsp_handle_port_status(struct cdnsp_device *pdev,
>> + union cdnsp_trb *event)
>> +{
>> + struct cdnsp_port_regs __iomem *port_regs;
>> + u32 portsc, cmd_regs;
>> + bool port2 = false;
>> + u32 link_state;
>> + u32 port_id;
>> +
>> + /* Port status change events always have a successful completion code */
>> + if (GET_COMP_CODE(le32_to_cpu(event->generic.field[2])) != COMP_SUCCESS)
>> + dev_err(pdev->dev, "ERR: incorrect PSC event\n");
>> +
>> + port_id = GET_PORT_ID(le32_to_cpu(event->generic.field[0]));
>> +
>> + if (cdnsp_update_port_id(pdev, port_id))
>> + goto cleanup;
>> +
>> + port_regs = pdev->active_port->regs;
>> +
>> + if (port_id == pdev->usb2_port.port_num)
>> + port2 = true;
>> +
>> +new_event:
>> + portsc = readl(&port_regs->portsc);
>> + writel(cdnsp_port_state_to_neutral(portsc) |
>> + (portsc & PORT_CHANGE_BITS), &port_regs->portsc);
>> +
>> + pdev->gadget.speed = cdnsp_port_speed(portsc);
>> + link_state = portsc & PORT_PLS_MASK;
>> +
>> + /* Port Link State change detected. */
>> + if ((portsc & PORT_PLC)) {
>> + if (!(pdev->cdnsp_state & CDNSP_WAKEUP_PENDING) &&
>> + link_state == XDEV_RESUME) {
>> + cmd_regs = readl(&pdev->op_regs->command);
>> + if (!(cmd_regs & CMD_R_S))
>> + goto cleanup;
>> +
>> + if (DEV_SUPERSPEED_ANY(portsc)) {
>> + cdnsp_set_link_state(pdev, &port_regs->portsc,
>> + XDEV_U0);
>> +
>> + cdnsp_resume_gadget(pdev);
>> + }
>> + }
>> +
>> + if ((pdev->cdnsp_state & CDNSP_WAKEUP_PENDING) &&
>> + link_state == XDEV_U0) {
>> + pdev->cdnsp_state &= ~CDNSP_WAKEUP_PENDING;
>> +
>> + cdnsp_force_header_wakeup(pdev, 1);
>> + cdnsp_ring_cmd_db(pdev);
>> + cdnsp_wait_for_cmd_compl(pdev);
>> + }
>> +
>> + if (link_state == XDEV_U0 && pdev->link_state == XDEV_U3 &&
>> + !DEV_SUPERSPEED_ANY(portsc))
>> + cdnsp_resume_gadget(pdev);
>> +
>> + if (link_state == XDEV_U3 && pdev->link_state != XDEV_U3)
>> + cdnsp_suspend_gadget(pdev);
>> +
>> + pdev->link_state = link_state;
>> + }
>> +
>> + if (portsc & PORT_CSC) {
>> + /* Detach device. */
>> + if (pdev->gadget.connected && !(portsc & PORT_CONNECT))
>> + cdnsp_disconnect_gadget(pdev);
>> +
>> + /* Attach device. */
>> + if (portsc & PORT_CONNECT) {
>> + if (!port2)
>> + cdnsp_irq_reset(pdev);
>> +
>> + usb_gadget_set_state(&pdev->gadget, USB_STATE_ATTACHED);
>> + }
>> + }
>> +
>> + /* Port reset. */
>> + if ((portsc & (PORT_RC | PORT_WRC)) && (portsc & PORT_CONNECT)) {
>> + cdnsp_irq_reset(pdev);
>> + pdev->u1_allowed = 0;
>> + pdev->u2_allowed = 0;
>> + pdev->may_wakeup = 0;
>> + }
>> +
>> + if (portsc & PORT_CEC)
>> + dev_err(pdev->dev, "Port Over Current detected\n");
>> +
>> + if (portsc & PORT_CEC)
>> + dev_err(pdev->dev, "Port Configure Error detected\n");
>> +
>> + if (readl(&port_regs->portsc) & PORT_CHANGE_BITS)
>> + goto new_event;
>> +
>> +cleanup:
>> + cdnsp_inc_deq(pdev, pdev->event_ring);
>> +}
>> +
>> +static void cdnsp_td_cleanup(struct cdnsp_device *pdev,
>> + struct cdnsp_td *td,
>> + struct cdnsp_ring *ep_ring,
>> + int *status)
>> +{
>> + struct cdnsp_request *preq = td->preq;
>> +
>> + /* if a bounce buffer was used to align this td then unmap it */
>> + cdnsp_unmap_td_bounce_buffer(pdev, ep_ring, td);
>> +
>> + /*
>> + * If the controller said we transferred more data than the buffer
>> + * length, Play it safe and say we didn't transfer anything.
>> + */
>> + if (preq->request.actual > preq->request.length) {
>> + preq->request.actual = 0;
>> + *status = 0;
>> + }
>> +
>> + list_del_init(&td->td_list);
>> + ep_ring->num_tds--;
>> + preq->pep->stream_info.td_count--;
>> +
>> + cdnsp_gadget_giveback(preq->pep, preq, *status);
>> +}
>> +
>> +static void cdnsp_finish_td(struct cdnsp_device *pdev,
>> + struct cdnsp_td *td,
>> + struct cdnsp_transfer_event *event,
>> + struct cdnsp_ep *ep,
>> + int *status)
>> +{
>> + struct cdnsp_ring *ep_ring;
>> + u32 trb_comp_code;
>> +
>> + ep_ring = cdnsp_dma_to_transfer_ring(ep, le64_to_cpu(event->buffer));
>> + trb_comp_code = GET_COMP_CODE(le32_to_cpu(event->transfer_len));
>> +
>> + if (trb_comp_code == COMP_STOPPED_LENGTH_INVALID ||
>> + trb_comp_code == COMP_STOPPED ||
>> + trb_comp_code == COMP_STOPPED_SHORT_PACKET) {
>> + /*
>> + * The Endpoint Stop Command completion will take care of any
>> + * stopped TDs. A stopped TD may be restarted, so don't update
>> + * the ring dequeue pointer or take this TD off any lists yet.
>> + */
>> + return;
>> + }
>> +
>> + /* Update ring dequeue pointer */
>> + while (ep_ring->dequeue != td->last_trb)
>> + cdnsp_inc_deq(pdev, ep_ring);
>> +
>> + cdnsp_inc_deq(pdev, ep_ring);
>> +
>> + cdnsp_td_cleanup(pdev, td, ep_ring, status);
>> +}
>> +
>> +/* sum trb lengths from ring dequeue up to stop_trb, _excluding_ stop_trb */
>> +static int cdnsp_sum_trb_lengths(struct cdnsp_device *pdev,
>> + struct cdnsp_ring *ring,
>> + union cdnsp_trb *stop_trb)
>> +{
>> + struct cdnsp_segment *seg = ring->deq_seg;
>> + union cdnsp_trb *trb = ring->dequeue;
>> + u32 sum;
>> +
>> + for (sum = 0; trb != stop_trb; cdnsp_next_trb(pdev, ring, &seg, &trb)) {
>> + if (!cdnsp_trb_is_noop(trb) && !cdnsp_trb_is_link(trb))
>> + sum += TRB_LEN(le32_to_cpu(trb->generic.field[2]));
>> + }
>> + return sum;
>> +}
>> +
>> +static int cdnsp_giveback_first_trb(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep,
>> + unsigned int stream_id,
>> + int start_cycle,
>> + struct cdnsp_generic_trb *start_trb)
>> +{
>> + /*
>> + * Pass all the TRBs to the hardware at once and make sure this write
>> + * isn't reordered.
>> + */
>> + wmb();
>> +
>> + if (start_cycle)
>> + start_trb->field[3] |= cpu_to_le32(start_cycle);
>> + else
>> + start_trb->field[3] &= cpu_to_le32(~TRB_CYCLE);
>> +
>> + if ((pep->ep_state & EP_HAS_STREAMS) &&
>> + !pep->stream_info.first_prime_det)
>> + return 0;
>> +
>> + return cdnsp_ring_ep_doorbell(pdev, pep, stream_id);
>> +}
>> +
>> +/*
>> + * Process control tds, update USB request status and actual_length.
>> + */
>> +static void cdnsp_process_ctrl_td(struct cdnsp_device *pdev,
>> + struct cdnsp_td *td,
>> + union cdnsp_trb *event_trb,
>> + struct cdnsp_transfer_event *event,
>> + struct cdnsp_ep *pep,
>> + int *status)
>> +{
>> + struct cdnsp_ring *ep_ring;
>> + u32 remaining;
>> + u32 trb_type;
>> +
>> + trb_type = TRB_FIELD_TO_TYPE(le32_to_cpu(event_trb->generic.field[3]));
>> + ep_ring = cdnsp_dma_to_transfer_ring(pep, le64_to_cpu(event->buffer));
>> + remaining = EVENT_TRB_LEN(le32_to_cpu(event->transfer_len));
>> +
>> + /*
>> + * if on data stage then update the actual_length of the USB
>> + * request and flag it as set, so it won't be overwritten in the event
>> + * for the last TRB.
>> + */
>> + if (trb_type == TRB_DATA) {
>> + td->request_length_set = true;
>> + td->preq->request.actual = td->preq->request.length - remaining;
>> + }
>> +
>> + /* at status stage */
>> + if (!td->request_length_set)
>> + td->preq->request.actual = td->preq->request.length;
>> +
>> + if (pdev->ep0_stage == CDNSP_DATA_STAGE && pep->number == 0 &&
>> + pdev->three_stage_setup) {
>> + td = list_entry(ep_ring->td_list.next, struct cdnsp_td,
>> + td_list);
>> + pdev->ep0_stage = CDNSP_STATUS_STAGE;
>> +
>> + cdnsp_giveback_first_trb(pdev, pep, 0, ep_ring->cycle_state,
>> + &td->last_trb->generic);
>> + return;
>> + }
>> +
>> + cdnsp_finish_td(pdev, td, event, pep, status);
>> +}
>> +
>> +/*
>> + * Process isochronous tds, update usb request status and actual_length.
>> + */
>> +static void cdnsp_process_isoc_td(struct cdnsp_device *pdev,
>> + struct cdnsp_td *td,
>> + union cdnsp_trb *ep_trb,
>> + struct cdnsp_transfer_event *event,
>> + struct cdnsp_ep *pep,
>> + int status)
>> +{
>> + struct cdnsp_request *preq = td->preq;
>> + u32 remaining, requested, ep_trb_len;
>> + bool sum_trbs_for_length = false;
>> + struct cdnsp_ring *ep_ring;
>> + u32 trb_comp_code;
>> + u32 td_length;
>> +
>> + ep_ring = cdnsp_dma_to_transfer_ring(pep, le64_to_cpu(event->buffer));
>> + trb_comp_code = GET_COMP_CODE(le32_to_cpu(event->transfer_len));
>> + remaining = EVENT_TRB_LEN(le32_to_cpu(event->transfer_len));
>> + ep_trb_len = TRB_LEN(le32_to_cpu(ep_trb->generic.field[2]));
>> +
>> + requested = preq->request.length;
>> +
>> + /* handle completion code */
>> + switch (trb_comp_code) {
>> + case COMP_SUCCESS:
>> + preq->request.status = 0;
>> + break;
>> + case COMP_SHORT_PACKET:
>> + preq->request.status = 0;
>> + sum_trbs_for_length = true;
>> + break;
>> + case COMP_ISOCH_BUFFER_OVERRUN:
>> + case COMP_BABBLE_DETECTED_ERROR:
>> + preq->request.status = -EOVERFLOW;
>> + break;
>> + case COMP_STOPPED:
>> + sum_trbs_for_length = true;
>> + break;
>> + case COMP_STOPPED_SHORT_PACKET:
>> + /* field normally containing residue now contains transferred */
>> + preq->request.status = 0;
>> + requested = remaining;
>> + break;
>> + case COMP_STOPPED_LENGTH_INVALID:
>> + requested = 0;
>> + remaining = 0;
>> + break;
>> + default:
>> + sum_trbs_for_length = true;
>> + preq->request.status = -1;
>> + break;
>> + }
>> +
>> + if (sum_trbs_for_length) {
>> + td_length = cdnsp_sum_trb_lengths(pdev, ep_ring, ep_trb);
>> + td_length += ep_trb_len - remaining;
>> + } else {
>> + td_length = requested;
>> + }
>> +
>> + td->preq->request.actual += td_length;
>> +
>> + cdnsp_finish_td(pdev, td, event, pep, &status);
>> +}
>> +
>> +static void cdnsp_skip_isoc_td(struct cdnsp_device *pdev,
>> + struct cdnsp_td *td,
>> + struct cdnsp_transfer_event *event,
>> + struct cdnsp_ep *pep,
>> + int status)
>> +{
>> + struct cdnsp_ring *ep_ring;
>> +
>> + ep_ring = cdnsp_dma_to_transfer_ring(pep, le64_to_cpu(event->buffer));
>> + td->preq->request.status = -EXDEV;
>> + td->preq->request.actual = 0;
>> +
>> + /* Update ring dequeue pointer */
>> + while (ep_ring->dequeue != td->last_trb)
>> + cdnsp_inc_deq(pdev, ep_ring);
>> +
>> + cdnsp_inc_deq(pdev, ep_ring);
>> +
>> + cdnsp_td_cleanup(pdev, td, ep_ring, &status);
>> +}
>> +
>> +/*
>> + * Process bulk and interrupt tds, update usb request status and actual_length.
>> + */
>> +static void cdnsp_process_bulk_intr_td(struct cdnsp_device *pdev,
>> + struct cdnsp_td *td,
>> + union cdnsp_trb *ep_trb,
>> + struct cdnsp_transfer_event *event,
>> + struct cdnsp_ep *ep,
>> + int *status)
>> +{
>> + u32 remaining, requested, ep_trb_len;
>> + struct cdnsp_ring *ep_ring;
>> + u32 trb_comp_code;
>> +
>> + ep_ring = cdnsp_dma_to_transfer_ring(ep, le64_to_cpu(event->buffer));
>> + trb_comp_code = GET_COMP_CODE(le32_to_cpu(event->transfer_len));
>> + remaining = EVENT_TRB_LEN(le32_to_cpu(event->transfer_len));
>> + ep_trb_len = TRB_LEN(le32_to_cpu(ep_trb->generic.field[2]));
>> + requested = td->preq->request.length;
>> +
>> + switch (trb_comp_code) {
>> + case COMP_SUCCESS:
>> + case COMP_SHORT_PACKET:
>> + *status = 0;
>> + break;
>> + case COMP_STOPPED_SHORT_PACKET:
>> + td->preq->request.actual = remaining;
>> + goto finish_td;
>> + case COMP_STOPPED_LENGTH_INVALID:
>> + /* Stopped on ep trb with invalid length, exclude it. */
>> + ep_trb_len = 0;
>> + remaining = 0;
>> + break;
>> + }
>> +
>> + if (ep_trb == td->last_trb)
>> + ep_trb_len = requested - remaining;
>> + else
>> + ep_trb_len = cdnsp_sum_trb_lengths(pdev, ep_ring, ep_trb) +
>> + ep_trb_len - remaining;
>> + td->preq->request.actual = ep_trb_len;
>> +
>> +finish_td:
>> + ep->stream_info.drbls_count--;
>> +
>> + cdnsp_finish_td(pdev, td, event, ep, status);
>> +}
>> +
>> +static void cdnsp_handle_tx_nrdy(struct cdnsp_device *pdev,
>> + struct cdnsp_transfer_event *event)
>> +{
>> + struct cdnsp_generic_trb *generic;
>> + struct cdnsp_ring *ep_ring;
>> + struct cdnsp_ep *pep;
>> + int cur_stream;
>> + int ep_index;
>> + int host_sid;
>> + int dev_sid;
>> +
>> + generic = (struct cdnsp_generic_trb *)event;
>> + ep_index = TRB_TO_EP_ID(le32_to_cpu(event->flags)) - 1;
>> + dev_sid = TRB_TO_DEV_STREAM(le32_to_cpu(generic->field[0]));
>> + host_sid = TRB_TO_HOST_STREAM(le32_to_cpu(generic->field[2]));
>> +
>> + pep = &pdev->eps[ep_index];
>> +
>> + if (!(pep->ep_state & EP_HAS_STREAMS))
>> + return;
>> +
>> + if (host_sid == STREAM_PRIME_ACK) {
>> + pep->stream_info.first_prime_det = 1;
>> + for (cur_stream = 1; cur_stream < pep->stream_info.num_streams;
>> + cur_stream++) {
>> + ep_ring = pep->stream_info.stream_rings[cur_stream];
>> + ep_ring->stream_active = 1;
>> + ep_ring->stream_rejected = 0;
>> + }
>> + }
>> +
>> + if (host_sid == STREAM_REJECTED) {
>> + struct cdnsp_td *td, *td_temp;
>> +
>> + pep->stream_info.drbls_count--;
>> + ep_ring = pep->stream_info.stream_rings[dev_sid];
>> + ep_ring->stream_active = 0;
>> + ep_ring->stream_rejected = 1;
>> +
>> + list_for_each_entry_safe(td, td_temp, &ep_ring->td_list,
>> + td_list) {
>> + td->drbl = 0;
>> + }
>> + }
>> +
>> + cdnsp_ring_doorbell_for_active_rings(pdev, pep);
>> +}
>> +
>> +/*
>> + * If this function returns an error condition, it means it got a Transfer
>> + * event with a corrupted TRB DMA address or endpoint is disabled.
>> + */
>> +static int cdnsp_handle_tx_event(struct cdnsp_device *pdev,
>> + struct cdnsp_transfer_event *event)
>> +{
>> + const struct usb_endpoint_descriptor *desc;
>> + bool handling_skipped_tds = false;
>> + struct cdnsp_segment *ep_seg;
>> + struct cdnsp_ring *ep_ring;
>> + int status = -EINPROGRESS;
>> + union cdnsp_trb *ep_trb;
>> + dma_addr_t ep_trb_dma;
>> + struct cdnsp_ep *pep;
>> + struct cdnsp_td *td;
>> + u32 trb_comp_code;
>> + int invalidate;
>> + int ep_index;
>> +
>> + invalidate = le32_to_cpu(event->flags) & TRB_EVENT_INVALIDATE;
>> + ep_index = TRB_TO_EP_ID(le32_to_cpu(event->flags)) - 1;
>> + trb_comp_code = GET_COMP_CODE(le32_to_cpu(event->transfer_len));
>> + ep_trb_dma = le64_to_cpu(event->buffer);
>> +
>> + pep = &pdev->eps[ep_index];
>> + ep_ring = cdnsp_dma_to_transfer_ring(pep, le64_to_cpu(event->buffer));
>> +
>> + /*
>> + * If device is disconnect then all requests will be dequeued
>> + * by upper layers as part of disconnect sequence.
>> + * We don't want handle such event to avoid racing.
>> + */
>> + if (invalidate || !pdev->gadget.connected)
>> + goto cleanup;
>> +
>> + if (GET_EP_CTX_STATE(pep->out_ctx) == EP_STATE_DISABLED)
>> + goto err_out;
>> +
>> + /* Some transfer events don't always point to a trb*/
>> + if (!ep_ring) {
>> + switch (trb_comp_code) {
>> + case COMP_INVALID_STREAM_TYPE_ERROR:
>> + case COMP_INVALID_STREAM_ID_ERROR:
>> + case COMP_RING_UNDERRUN:
>> + case COMP_RING_OVERRUN:
>> + goto cleanup;
>> + default:
>> + dev_err(pdev->dev, "ERROR: %s event for unknown ring\n",
>> + pep->name);
>> + goto err_out;
>> + }
>> + }
>> +
>> + /* Look for some error cases that need special treatment. */
>> + switch (trb_comp_code) {
>> + case COMP_BABBLE_DETECTED_ERROR:
>> + status = -EOVERFLOW;
>> + break;
>> + case COMP_RING_UNDERRUN:
>> + case COMP_RING_OVERRUN:
>> + /*
>> + * When the Isoch ring is empty, the controller will generate
>> + * a Ring Overrun Event for IN Isoch endpoint or Ring
>> + * Underrun Event for OUT Isoch endpoint.
>> + */
>> + goto cleanup;
>> + case COMP_MISSED_SERVICE_ERROR:
>> + /*
>> + * When encounter missed service error, one or more isoc tds
>> + * may be missed by controller.
>> + * Set skip flag of the ep_ring; Complete the missed tds as
>> + * short transfer when process the ep_ring next time.
>> + */
>> + pep->skip = true;
>> + break;
>> + }
>> +
>> + do {
>> + /*
>> + * This TRB should be in the TD at the head of this ring's TD
>> + * list.
>> + */
>> + if (list_empty(&ep_ring->td_list)) {
>> + if (pep->skip)
>> + pep->skip = false;
>> +
>> + goto cleanup;
>> + }
>> +
>> + td = list_entry(ep_ring->td_list.next, struct cdnsp_td,
>> + td_list);
>> +
>> + /* Is this a TRB in the currently executing TD? */
>> + ep_seg = cdnsp_trb_in_td(pdev, ep_ring->deq_seg,
>> + ep_ring->dequeue, td->last_trb,
>> + ep_trb_dma);
>> +
>> + /*
>> + * Skip the Force Stopped Event. The event_trb(ep_trb_dma)
>> + * of FSE is not in the current TD pointed by ep_ring->dequeue
>> + * because that the hardware dequeue pointer still at the
>> + * previous TRB of the current TD. The previous TRB maybe a
>> + * Link TD or the last TRB of the previous TD. The command
>> + * completion handle will take care the rest.
>> + */
>> + if (!ep_seg && (trb_comp_code == COMP_STOPPED ||
>> + trb_comp_code == COMP_STOPPED_LENGTH_INVALID)) {
>> + pep->skip = false;
>> + goto cleanup;
>> + }
>> +
>> + desc = td->preq->pep->endpoint.desc;
>> + if (!ep_seg) {
>> + if (!pep->skip || !usb_endpoint_xfer_isoc(desc)) {
>> + /* Something is busted, give up! */
>> + dev_err(pdev->dev,
>> + "ERROR Transfer event TRB DMA ptr not "
>> + "part of current TD ep_index %d "
>> + "comp_code %u\n", ep_index,
>> + trb_comp_code);
>> + return -EINVAL;
>> + }
>> +
>> + cdnsp_skip_isoc_td(pdev, td, event, pep, status);
>> + goto cleanup;
>> + }
>> +
>> + if (trb_comp_code == COMP_SHORT_PACKET)
>> + ep_ring->last_td_was_short = true;
>> + else
>> + ep_ring->last_td_was_short = false;
>> +
>> + if (pep->skip) {
>> + pep->skip = false;
>> + cdnsp_skip_isoc_td(pdev, td, event, pep, status);
>> + goto cleanup;
>> + }
>> +
>> + ep_trb = &ep_seg->trbs[(ep_trb_dma - ep_seg->dma)
>> + / sizeof(*ep_trb)];
>> +
>> + if (cdnsp_trb_is_noop(ep_trb))
>> + goto cleanup;
>> +
>> + if (usb_endpoint_xfer_control(desc))
>> + cdnsp_process_ctrl_td(pdev, td, ep_trb, event, pep,
>> + &status);
>> + else if (usb_endpoint_xfer_isoc(desc))
>> + cdnsp_process_isoc_td(pdev, td, ep_trb, event, pep,
>> + status);
>> + else
>> + cdnsp_process_bulk_intr_td(pdev, td, ep_trb, event, pep,
>> + &status);
>> +cleanup:
>> + handling_skipped_tds = pep->skip;
>> +
>> + /*
>> + * Do not update event ring dequeue pointer if we're in a loop
>> + * processing missed tds.
>> + */
>> + if (!handling_skipped_tds)
>> + cdnsp_inc_deq(pdev, pdev->event_ring);
>> +
>> + /*
>> + * If ep->skip is set, it means there are missed tds on the
>> + * endpoint ring need to take care of.
>> + * Process them as short transfer until reach the td pointed by
>> + * the event.
>> + */
>> + } while (handling_skipped_tds);
>> + return 0;
>> +
>> +err_out:
>> + dev_err(pdev->dev, "@%016llx %08x %08x %08x %08x\n",
>> + (unsigned long long)
>> + cdnsp_trb_virt_to_dma(pdev->event_ring->deq_seg,
>> + pdev->event_ring->dequeue),
>> + lower_32_bits(le64_to_cpu(event->buffer)),
>> + upper_32_bits(le64_to_cpu(event->buffer)),
>> + le32_to_cpu(event->transfer_len),
>> + le32_to_cpu(event->flags));
>> + return -EINVAL;
>> +}
>> +
>> +/*
>> + * This function handles all events on the event ring.
>> + * Returns true for "possibly more events to process" (caller should call
>> + * again), otherwise false if done.
>> + */
>> +static bool cdnsp_handle_event(struct cdnsp_device *pdev)
>> +{
>> + unsigned int comp_code;
>> + union cdnsp_trb *event;
>> + bool update_ptrs = true;
>> + __le32 cycle_bit;
>> + int ret = 0;
>> + u32 flags;
>> +
>> + event = pdev->event_ring->dequeue;
>> + flags = le32_to_cpu(event->event_cmd.flags);
>> + cycle_bit = (flags & TRB_CYCLE);
>> +
>> + /* Does the controller or driver own the TRB? */
>> + if (cycle_bit != pdev->event_ring->cycle_state)
>> + return false;
>> +
>> + /*
>> + * Barrier between reading the TRB_CYCLE (valid) flag above and any
>> + * reads of the event's flags/data below.
>> + */
>> + rmb();
>> +
>> + switch (flags & TRB_TYPE_BITMASK) {
>> + case TRB_TYPE(TRB_COMPLETION):
>> + /*
>> + * Command can't be handled in interrupt context so just
>> + * increment command ring dequeue pointer.
>> + */
>> + cdnsp_inc_deq(pdev, pdev->cmd_ring);
>> + break;
>> + case TRB_TYPE(TRB_PORT_STATUS):
>> + cdnsp_handle_port_status(pdev, event);
>> + update_ptrs = false;
>> + break;
>> + case TRB_TYPE(TRB_TRANSFER):
>> + ret = cdnsp_handle_tx_event(pdev, &event->trans_event);
>> + if (ret >= 0)
>> + update_ptrs = false;
>> + break;
>> + case TRB_TYPE(TRB_SETUP):
>> + pdev->ep0_stage = CDNSP_SETUP_STAGE;
>> + pdev->setup_id = TRB_SETUPID_TO_TYPE(flags);
>> + pdev->setup_speed = TRB_SETUP_SPEEDID(flags);
>> + pdev->setup = *((struct usb_ctrlrequest *)
>> + &event->trans_event.buffer);
>> +
>> + cdnsp_setup_analyze(pdev);
>> + break;
>> + case TRB_TYPE(TRB_ENDPOINT_NRDY):
>> + cdnsp_handle_tx_nrdy(pdev, &event->trans_event);
>> + break;
>> + case TRB_TYPE(TRB_HC_EVENT): {
>> + comp_code = GET_COMP_CODE(le32_to_cpu(event->generic.field[2]));
>> +
>> + switch (comp_code) {
>> + case COMP_EVENT_RING_FULL_ERROR:
>> + dev_err(pdev->dev, "Event Ring Full\n");
>> + break;
>> + default:
>> + dev_err(pdev->dev, "Controller error code 0x%02x\n",
>> + comp_code);
>> + }
>> +
>> + break;
>> + }
>> + case TRB_TYPE(TRB_MFINDEX_WRAP):
>> + case TRB_TYPE(TRB_DRB_OVERFLOW):
>> + break;
>> + default:
>> + dev_warn(pdev->dev, "ERROR unknown event type %ld\n",
>> + TRB_FIELD_TO_TYPE(flags));
>> + }
>> +
>> + if (update_ptrs)
>> + /* Update SW event ring dequeue pointer. */
>> + cdnsp_inc_deq(pdev, pdev->event_ring);
>> +
>> + /*
>> + * Caller will call us again to check if there are more items
>> + * on the event ring.
>> + */
>> + return true;
>> +}
>> +
>> +irqreturn_t cdnsp_thread_irq_handler(int irq, void *data)
>> +{
>> + struct cdnsp_device *pdev = (struct cdnsp_device *)data;
>> + union cdnsp_trb *event_ring_deq;
>> + int counter = 0;
>> +
>> + spin_lock(&pdev->lock);
>> +
>> + if (pdev->cdnsp_state & (CDNSP_STATE_HALTED | CDNSP_STATE_DYING)) {
>> + cdnsp_died(pdev);
>> + spin_unlock(&pdev->lock);
>> + return IRQ_HANDLED;
>> + }
>> +
>> + event_ring_deq = pdev->event_ring->dequeue;
>> +
>> + while (cdnsp_handle_event(pdev)) {
>> + if (++counter >= TRBS_PER_EV_DEQ_UPDATE) {
>> + cdnsp_update_erst_dequeue(pdev, event_ring_deq, 0);
>> + event_ring_deq = pdev->event_ring->dequeue;
>> + counter = 0;
>> + }
>> + }
>> +
>> + cdnsp_update_erst_dequeue(pdev, event_ring_deq, 1);
>> +
>> + spin_unlock(&pdev->lock);
>> +
>> + return IRQ_HANDLED;
>> +}
>> +
>> +irqreturn_t cdnsp_irq_handler(int irq, void *priv)
>> +{
>> + struct cdnsp_device *pdev = (struct cdnsp_device *)priv;
>> + u32 irq_pending;
>> + u32 status;
>> +
>> + status = readl(&pdev->op_regs->status);
>> +
>> + if (status == ~(u32)0) {
>> + cdnsp_died(pdev);
>> + return IRQ_HANDLED;
>> + }
>> +
>> + if (!(status & STS_EINT))
>> + return IRQ_NONE;
>> +
>> + writel(status | STS_EINT, &pdev->op_regs->status);
>> + irq_pending = readl(&pdev->ir_set->irq_pending);
>> + irq_pending |= IMAN_IP;
>> + writel(irq_pending, &pdev->ir_set->irq_pending);
>> +
>> + if (status & STS_FATAL) {
>> + cdnsp_died(pdev);
>> + return IRQ_HANDLED;
>> + }
>> +
>> + return IRQ_WAKE_THREAD;
>> +}
>> +
>> +/*
>> + * Generic function for queuing a TRB on a ring.
>> + * The caller must have checked to make sure there's room on the ring.
>> + *
>> + * @more_trbs_coming: Will you enqueue more TRBs before setting doorbell?
>> + */
>> +static void cdnsp_queue_trb(struct cdnsp_device *pdev, struct cdnsp_ring *ring,
>> + bool more_trbs_coming, u32 field1, u32 field2,
>> + u32 field3, u32 field4)
>> +{
>> + struct cdnsp_generic_trb *trb;
>> +
>> + trb = &ring->enqueue->generic;
>> +
>> + trb->field[0] = cpu_to_le32(field1);
>> + trb->field[1] = cpu_to_le32(field2);
>> + trb->field[2] = cpu_to_le32(field3);
>> + trb->field[3] = cpu_to_le32(field4);
>> +
>> + cdnsp_inc_enq(pdev, ring, more_trbs_coming);
>> +}
>> +
>> +/*
>> + * Does various checks on the endpoint ring, and makes it ready to
>> + * queue num_trbs.
>> + */
>> +static int cdnsp_prepare_ring(struct cdnsp_device *pdev,
>> + struct cdnsp_ring *ep_ring,
>> + u32 ep_state, unsigned
>> + int num_trbs,
>> + gfp_t mem_flags)
>> +{
>> + unsigned int num_trbs_needed;
>> +
>> + /* Make sure the endpoint has been added to controller schedule. */
>> + switch (ep_state) {
>> + case EP_STATE_STOPPED:
>> + case EP_STATE_RUNNING:
>> + case EP_STATE_HALTED:
>> + break;
>> + default:
>> + dev_err(pdev->dev, "ERROR: incorrect endpoint state\n");
>> + return -EINVAL;
>> + }
>> +
>> + while (1) {
>> + if (cdnsp_room_on_ring(pdev, ep_ring, num_trbs))
>> + break;
>> +
>> + num_trbs_needed = num_trbs - ep_ring->num_trbs_free;
>> + if (cdnsp_ring_expansion(pdev, ep_ring, num_trbs_needed,
>> + mem_flags)) {
>> + dev_err(pdev->dev, "Ring expansion failed\n");
>> + return -ENOMEM;
>> + }
>> + }
>> +
>> + while (cdnsp_trb_is_link(ep_ring->enqueue)) {
>> + ep_ring->enqueue->link.control |= cpu_to_le32(TRB_CHAIN);
>> + /* The cycle bit must be set as the last operation. */
>> + wmb();
>> + ep_ring->enqueue->link.control ^= cpu_to_le32(TRB_CYCLE);
>> +
>> + /* Toggle the cycle bit after the last ring segment. */
>> + if (cdnsp_link_trb_toggles_cycle(ep_ring->enqueue))
>> + ep_ring->cycle_state ^= 1;
>> + ep_ring->enq_seg = ep_ring->enq_seg->next;
>> + ep_ring->enqueue = ep_ring->enq_seg->trbs;
>> + }
>> + return 0;
>> +}
>> +
>> +static int cdnsp_prepare_transfer(struct cdnsp_device *pdev,
>> + struct cdnsp_request *preq,
>> + unsigned int num_trbs)
>> +{
>> + struct cdnsp_ring *ep_ring;
>> + int ret;
>> +
>> + ep_ring = cdnsp_get_transfer_ring(pdev, preq->pep,
>> + preq->request.stream_id);
>> + if (!ep_ring)
>> + return -EINVAL;
>> +
>> + ret = cdnsp_prepare_ring(pdev, ep_ring,
>> + GET_EP_CTX_STATE(preq->pep->out_ctx),
>> + num_trbs, GFP_ATOMIC);
>> + if (ret)
>> + return ret;
>> +
>> + INIT_LIST_HEAD(&preq->td.td_list);
>> + preq->td.preq = preq;
>> +
>> + /* Add this TD to the tail of the endpoint ring's TD list. */
>> + list_add_tail(&preq->td.td_list, &ep_ring->td_list);
>> + ep_ring->num_tds++;
>> + preq->pep->stream_info.td_count++;
>> +
>> + preq->td.start_seg = ep_ring->enq_seg;
>> + preq->td.first_trb = ep_ring->enqueue;
>> +
>> + return 0;
>> +}
>> +
>> +static unsigned int cdnsp_count_trbs(u64 addr, u64 len)
>> +{
>> + unsigned int num_trbs;
>> +
>> + num_trbs = DIV_ROUND_UP(len + (addr & (TRB_MAX_BUFF_SIZE - 1)),
>> + TRB_MAX_BUFF_SIZE);
>> + if (num_trbs == 0)
>> + num_trbs++;
>> +
>> + return num_trbs;
>> +}
>> +
>> +static unsigned int count_trbs_needed(struct cdnsp_request *preq)
>> +{
>> + return cdnsp_count_trbs(preq->request.dma, preq->request.length);
>> +}
>> +
>> +static unsigned int count_sg_trbs_needed(struct cdnsp_request *preq)
>> +{
>> + unsigned int i, len, full_len, num_trbs = 0;
>> + struct scatterlist *sg;
>> +
>> + full_len = preq->request.length;
>> +
>> + for_each_sg(preq->request.sg, sg, preq->request.num_sgs, i) {
>> + len = sg_dma_len(sg);
>> + num_trbs += cdnsp_count_trbs(sg_dma_address(sg), len);
>> + len = min(len, full_len);
>> + full_len -= len;
>> + if (full_len == 0)
>> + break;
>> + }
>> +
>> + return num_trbs;
>> +}
>> +
>> +static unsigned int count_isoc_trbs_needed(struct cdnsp_request *preq)
>> +{
>> + return cdnsp_count_trbs(preq->request.dma, preq->request.length);
>> +}
>> +
>> +static void cdnsp_check_trb_math(struct cdnsp_request *preq, int running_total)
>> +{
>> + if (running_total != preq->request.length)
>> + dev_err(preq->pep->pdev->dev,
>> + "%s - Miscalculated tx length, "
>> + "queued %#x, asked for %#x (%d)\n",
>> + preq->pep->name, running_total,
>> + preq->request.length, preq->request.actual);
>> +}
>> +
>> +/*
>> + * TD size is the number of max packet sized packets remaining in the TD
>> + * (*not* including this TRB).
>> + *
>> + * Total TD packet count = total_packet_count =
>> + * DIV_ROUND_UP(TD size in bytes / wMaxPacketSize)
>> + *
>> + * Packets transferred up to and including this TRB = packets_transferred =
>> + * rounddown(total bytes transferred including this TRB / wMaxPacketSize)
>> + *
>> + * TD size = total_packet_count - packets_transferred
>> + *
>> + * It must fit in bits 21:17, so it can't be bigger than 31.
>> + * This is taken care of in the TRB_TD_SIZE() macro
>> + *
>> + * The last TRB in a TD must have the TD size set to zero.
>> + */
>> +static u32 cdnsp_td_remainder(struct cdnsp_device *pdev,
>> + int transferred,
>> + int trb_buff_len,
>> + unsigned int td_total_len,
>> + struct cdnsp_request *preq,
>> + bool more_trbs_coming)
>> +{
>> + u32 maxp, total_packet_count;
>> +
>> + /* One TRB with a zero-length data packet. */
>> + if (!more_trbs_coming || (transferred == 0 && trb_buff_len == 0) ||
>> + trb_buff_len == td_total_len)
>> + return 0;
>> +
>> + maxp = usb_endpoint_maxp(preq->pep->endpoint.desc);
>> + total_packet_count = DIV_ROUND_UP(td_total_len, maxp);
>> +
>> + /* Queuing functions don't count the current TRB into transferred. */
>> + return (total_packet_count - ((transferred + trb_buff_len) / maxp));
>> +}
>> +
>> +static int cdnsp_align_td(struct cdnsp_device *pdev,
>> + struct cdnsp_request *preq, u32 enqd_len,
>> + u32 *trb_buff_len, struct cdnsp_segment *seg)
>> +{
>> + struct device *dev = pdev->dev;
>> + unsigned int unalign;
>> + unsigned int max_pkt;
>> + u32 new_buff_len;
>> +
>> + max_pkt = usb_endpoint_maxp(preq->pep->endpoint.desc);
>> + unalign = (enqd_len + *trb_buff_len) % max_pkt;
>> +
>> + /* We got lucky, last normal TRB data on segment is packet aligned. */
>> + if (unalign == 0)
>> + return 0;
>> +
>> + /* Is the last nornal TRB alignable by splitting it. */
>> + if (*trb_buff_len > unalign) {
>> + *trb_buff_len -= unalign;
>> + return 0;
>> + }
>> +
>> + /*
>> + * We want enqd_len + trb_buff_len to sum up to a number aligned to
>> + * number which is divisible by the endpoint's wMaxPacketSize. IOW:
>> + * (size of currently enqueued TRBs + remainder) % wMaxPacketSize == 0.
>> + */
>> + new_buff_len = max_pkt - (enqd_len % max_pkt);
>> +
>> + if (new_buff_len > (preq->request.length - enqd_len))
>> + new_buff_len = (preq->request.length - enqd_len);
>> +
>> + /* Create a max max_pkt sized bounce buffer pointed to by last trb. */
>> + if (preq->direction) {
>> + sg_pcopy_to_buffer(preq->request.sg,
>> + preq->request.num_mapped_sgs,
>> + seg->bounce_buf, new_buff_len, enqd_len);
>> + seg->bounce_dma = dma_map_single(dev, seg->bounce_buf,
>> + max_pkt, DMA_TO_DEVICE);
>> + } else {
>> + seg->bounce_dma = dma_map_single(dev, seg->bounce_buf,
>> + max_pkt, DMA_FROM_DEVICE);
>> + }
>> +
>> + if (dma_mapping_error(dev, seg->bounce_dma)) {
>> + /* Try without aligning.*/
>> + dev_warn(pdev->dev,
>> + "Failed mapping bounce buffer, not aligning\n");
>> + return 0;
>> + }
>> +
>> + *trb_buff_len = new_buff_len;
>> + seg->bounce_len = new_buff_len;
>> + seg->bounce_offs = enqd_len;
>> +
>> + /*
>> + * Bounce buffer successful aligned and seg->bounce_dma will be used
>> + * in transfer TRB as new transfer buffer address.
>> + */
>> + return 1;
>> +}
>> +
>> +int cdnsp_queue_bulk_tx(struct cdnsp_device *pdev, struct cdnsp_request *preq)
>> +{
>> + unsigned int enqd_len, block_len, trb_buff_len, full_len;
>> + unsigned int start_cycle, num_sgs = 0;
>> + struct cdnsp_generic_trb *start_trb;
>> + u32 field, length_field, remainder;
>> + struct scatterlist *sg = NULL;
>> + bool more_trbs_coming = true;
>> + bool need_zero_pkt = false;
>> + bool zero_len_trb = false;
>> + struct cdnsp_ring *ring;
>> + bool first_trb = true;
>> + unsigned int num_trbs;
>> + struct cdnsp_ep *pep;
>> + u64 addr, send_addr;
>> + int sent_len, ret;
>> +
>> + ring = cdnsp_request_to_transfer_ring(pdev, preq);
>> + if (!ring)
>> + return -EINVAL;
>> +
>> + full_len = preq->request.length;
>> +
>> + if (preq->request.num_sgs) {
>> + num_sgs = preq->request.num_sgs;
>> + sg = preq->request.sg;
>> + addr = (u64)sg_dma_address(sg);
>> + block_len = sg_dma_len(sg);
>> + num_trbs = count_sg_trbs_needed(preq);
>> + } else {
>> + num_trbs = count_trbs_needed(preq);
>> + addr = (u64)preq->request.dma;
>> + block_len = full_len;
>> + }
>> +
>> + pep = preq->pep;
>> +
>> + /* Deal with request.zero - need one more td/trb. */
>> + if (preq->request.zero && preq->request.length &&
>> + IS_ALIGNED(full_len, usb_endpoint_maxp(pep->endpoint.desc))) {
>> + need_zero_pkt = true;
>> + num_trbs++;
>> + }
>> +
>> + ret = cdnsp_prepare_transfer(pdev, preq, num_trbs);
>> + if (ret)
>> + return ret;
>> +
>> + /*
>> + * Don't give the first TRB to the hardware (by toggling the cycle bit)
>> + * until we've finished creating all the other TRBs. The ring's cycle
>> + * state may change as we enqueue the other TRBs, so save it too.
>> + */
>> + start_trb = &ring->enqueue->generic;
>> + start_cycle = ring->cycle_state;
>> + send_addr = addr;
>> +
>> + /* Queue the TRBs, even if they are zero-length */
>> + for (enqd_len = 0; zero_len_trb || first_trb || enqd_len < full_len;
>> + enqd_len += trb_buff_len) {
>> + field = TRB_TYPE(TRB_NORMAL);
>> +
>> + /* TRB buffer should not cross 64KB boundaries */
>> + trb_buff_len = TRB_BUFF_LEN_UP_TO_BOUNDARY(addr);
>> + trb_buff_len = min(trb_buff_len, block_len);
>> + if (enqd_len + trb_buff_len > full_len)
>> + trb_buff_len = full_len - enqd_len;
>> +
>> + /* Don't change the cycle bit of the first TRB until later */
>> + if (first_trb) {
>> + first_trb = false;
>> + if (start_cycle == 0)
>> + field |= TRB_CYCLE;
>> + } else {
>> + field |= ring->cycle_state;
>> + }
>> +
>> + /*
>> + * Chain all the TRBs together; clear the chain bit in the last
>> + * TRB to indicate it's the last TRB in the chain.
>> + */
>> + if (enqd_len + trb_buff_len < full_len || need_zero_pkt) {
>> + field |= TRB_CHAIN;
>> + if (cdnsp_trb_is_link(ring->enqueue + 1)) {
>> + if (cdnsp_align_td(pdev, preq, enqd_len,
>> + &trb_buff_len,
>> + ring->enq_seg)) {
>> + send_addr = ring->enq_seg->bounce_dma;
>> + /* Assuming TD won't span 2 segs */
>> + preq->td.bounce_seg = ring->enq_seg;
>> + }
>> + }
>> + }
>> +
>> + if (enqd_len + trb_buff_len >= full_len) {
>> + if (need_zero_pkt && zero_len_trb) {
>> + zero_len_trb = true;
>> + } else {
>> + field &= ~TRB_CHAIN;
>> + field |= TRB_IOC;
>> + more_trbs_coming = false;
>> + need_zero_pkt = false;
>> + preq->td.last_trb = ring->enqueue;
>> + }
>> + }
>> +
>> + /* Only set interrupt on short packet for OUT endpoints. */
>> + if (!preq->direction)
>> + field |= TRB_ISP;
>> +
>> + /* Set the TRB length, TD size, and interrupter fields. */
>> + remainder = cdnsp_td_remainder(pdev, enqd_len, trb_buff_len,
>> + full_len, preq,
>> + more_trbs_coming);
>> +
>> + length_field = TRB_LEN(trb_buff_len) | TRB_TD_SIZE(remainder) |
>> + TRB_INTR_TARGET(0);
>> +
>> + cdnsp_queue_trb(pdev, ring, more_trbs_coming | need_zero_pkt,
>> + lower_32_bits(send_addr),
>> + upper_32_bits(send_addr),
>> + length_field,
>> + field);
>> +
>> + addr += trb_buff_len;
>> + sent_len = trb_buff_len;
>> + while (sg && sent_len >= block_len) {
>> + /* New sg entry */
>> + --num_sgs;
>> + sent_len -= block_len;
>> + if (num_sgs != 0) {
>> + sg = sg_next(sg);
>> + block_len = sg_dma_len(sg);
>> + addr = (u64)sg_dma_address(sg);
>> + addr += sent_len;
>> + }
>> + }
>> + block_len -= sent_len;
>> + send_addr = addr;
>> + }
>> +
>> + cdnsp_check_trb_math(preq, enqd_len);
>> + ret = cdnsp_giveback_first_trb(pdev, pep, preq->request.stream_id,
>> + start_cycle, start_trb);
>> +
>> + if (ret)
>> + preq->td.drbl = 1;
>> +
>> + return 0;
>> +}
>> +
>> +int cdnsp_queue_ctrl_tx(struct cdnsp_device *pdev, struct cdnsp_request *preq)
>> +{
>> + u32 field, length_field, remainder;
>> + struct cdnsp_ep *pep = preq->pep;
>> + struct cdnsp_ring *ep_ring;
>> + int num_trbs;
>> + int ret;
>> +
>> + ep_ring = cdnsp_request_to_transfer_ring(pdev, preq);
>> + if (!ep_ring)
>> + return -EINVAL;
>> +
>> + /* 1 TRB for data, 1 for status */
>> + num_trbs = (pdev->three_stage_setup) ? 2 : 1;
>> +
>> + ret = cdnsp_prepare_transfer(pdev, preq, num_trbs);
>> + if (ret)
>> + return ret;
>> +
>> + /* If there's data, queue data TRBs */
>> + if (pdev->ep0_expect_in)
>> + field = TRB_TYPE(TRB_DATA) | TRB_IOC;
>> + else
>> + field = TRB_ISP | TRB_TYPE(TRB_DATA) | TRB_IOC;
>> +
>> + if (preq->request.length > 0) {
>> + remainder = cdnsp_td_remainder(pdev, 0, preq->request.length,
>> + preq->request.length, preq, 1);
>> +
>> + length_field = TRB_LEN(preq->request.length) |
>> + TRB_TD_SIZE(remainder) | TRB_INTR_TARGET(0);
>> +
>> + if (pdev->ep0_expect_in)
>> + field |= TRB_DIR_IN;
>> +
>> + cdnsp_queue_trb(pdev, ep_ring, true,
>> + lower_32_bits(preq->request.dma),
>> + upper_32_bits(preq->request.dma), length_field,
>> + field | ep_ring->cycle_state |
>> + TRB_SETUPID(pdev->setup_id) |
>> + pdev->setup_speed);
>> +
>> + pdev->ep0_stage = CDNSP_DATA_STAGE;
>> + }
>> +
>> + /* Save the DMA address of the last TRB in the TD. */
>> + preq->td.last_trb = ep_ring->enqueue;
>> +
>> + /* Queue status TRB. */
>> + if (preq->request.length == 0)
>> + field = ep_ring->cycle_state;
>> + else
>> + field = (ep_ring->cycle_state ^ 1);
>> +
>> + if (preq->request.length > 0 && pdev->ep0_expect_in)
>> + field |= TRB_DIR_IN;
>> +
>> + if (pep->ep_state & EP0_HALTED_STATUS) {
>> + pep->ep_state &= ~EP0_HALTED_STATUS;
>> + field |= TRB_SETUPSTAT(TRB_SETUPSTAT_STALL);
>> + } else {
>> + field |= TRB_SETUPSTAT(TRB_SETUPSTAT_ACK);
>> + }
>> +
>> + cdnsp_queue_trb(pdev, ep_ring, false, 0, 0, TRB_INTR_TARGET(0),
>> + field | TRB_IOC | TRB_SETUPID(pdev->setup_id) |
>> + TRB_TYPE(TRB_STATUS) | pdev->setup_speed);
>> +
>> + cdnsp_ring_ep_doorbell(pdev, pep, preq->request.stream_id);
>> +
>> + return 0;
>> +}
>> +
>> +int cdnsp_cmd_stop_ep(struct cdnsp_device *pdev, struct cdnsp_ep *pep)
>> +{
>> + u32 ep_state = GET_EP_CTX_STATE(pep->out_ctx);
>> + int ret = 0;
>> +
>> + if (ep_state == EP_STATE_STOPPED || ep_state == EP_STATE_DISABLED)
>> + goto ep_stopped;
>> +
>> + cdnsp_queue_stop_endpoint(pdev, pep->idx);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> +
>> +ep_stopped:
>> + pep->ep_state |= EP_STOPPED;
>> + return ret;
>> +}
>> +
>> +int cdnsp_cmd_flush_ep(struct cdnsp_device *pdev, struct cdnsp_ep *pep)
>> +{
>> + int ret;
>> +
>> + cdnsp_queue_flush_endpoint(pdev, pep->idx);
>> + cdnsp_ring_cmd_db(pdev);
>> + ret = cdnsp_wait_for_cmd_compl(pdev);
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * The transfer burst count field of the isochronous TRB defines the number of
>> + * bursts that are required to move all packets in this TD. Only SuperSpeed
>> + * devices can burst up to bMaxBurst number of packets per service interval.
>> + * This field is zero based, meaning a value of zero in the field means one
>> + * burst. Basically, for everything but SuperSpeed devices, this field will be
>> + * zero.
>> + */
>> +static unsigned int cdnsp_get_burst_count(struct cdnsp_device *pdev,
>> + struct cdnsp_request *preq,
>> + unsigned int total_packet_count)
>> +{
>> + unsigned int max_burst;
>> +
>> + if (pdev->gadget.speed < USB_SPEED_SUPER)
>> + return 0;
>> +
>> + max_burst = preq->pep->endpoint.comp_desc->bMaxBurst;
>> + return DIV_ROUND_UP(total_packet_count, max_burst + 1) - 1;
>> +}
>> +
>> +/*
>> + * Returns the number of packets in the last "burst" of packets. This field is
>> + * valid for all speeds of devices. USB 2.0 devices can only do one "burst", so
>> + * the last burst packet count is equal to the total number of packets in the
>> + * TD. SuperSpeed endpoints can have up to 3 bursts. All but the last burst
>> + * must contain (bMaxBurst + 1) number of packets, but the last burst can
>> + * contain 1 to (bMaxBurst + 1) packets.
>> + */
>> +static unsigned int
>> + cdnsp_get_last_burst_packet_count(struct cdnsp_device *pdev,
>> + struct cdnsp_request *preq,
>> + unsigned int total_packet_count)
>> +{
>> + unsigned int max_burst;
>> + unsigned int residue;
>> +
>> + if (pdev->gadget.speed >= USB_SPEED_SUPER) {
>> + /* bMaxBurst is zero based: 0 means 1 packet per burst. */
>> + max_burst = preq->pep->endpoint.comp_desc->bMaxBurst;
>> + residue = total_packet_count % (max_burst + 1);
>> +
>> + /*
>> + * If residue is zero, the last burst contains (max_burst + 1)
>> + * number of packets, but the TLBPC field is zero-based.
>> + */
>> + if (residue == 0)
>> + return max_burst;
>> +
>> + return residue - 1;
>> + }
>> + if (total_packet_count == 0)
>> + return 0;
>> +
>> + return total_packet_count - 1;
>> +}
>> +
>> +/* Queue function isoc transfer */
>> +static int cdnsp_queue_isoc_tx(struct cdnsp_device *pdev,
>> + struct cdnsp_request *preq)
>> +{
>> + int trb_buff_len, td_len, td_remain_len, ret;
>> + unsigned int burst_count, last_burst_pkt;
>> + unsigned int total_pkt_count, max_pkt;
>> + struct cdnsp_generic_trb *start_trb;
>> + bool more_trbs_coming = true;
>> + struct cdnsp_ring *ep_ring;
>> + int running_total = 0;
>> + u32 field, length_field;
>> + int start_cycle;
>> + int trbs_per_td;
>> + u64 addr;
>> + int i;
>> +
>> + ep_ring = preq->pep->ring;
>> + start_trb = &ep_ring->enqueue->generic;
>> + start_cycle = ep_ring->cycle_state;
>> + td_len = preq->request.length;
>> + addr = (u64)preq->request.dma;
>> + td_remain_len = td_len;
>> +
>> + max_pkt = usb_endpoint_maxp(preq->pep->endpoint.desc);
>> + total_pkt_count = DIV_ROUND_UP(td_len, max_pkt);
>> +
>> + /* A zero-length transfer still involves at least one packet. */
>> + if (total_pkt_count == 0)
>> + total_pkt_count++;
>> +
>> + burst_count = cdnsp_get_burst_count(pdev, preq, total_pkt_count);
>> + last_burst_pkt = cdnsp_get_last_burst_packet_count(pdev, preq,
>> + total_pkt_count);
>> + trbs_per_td = count_isoc_trbs_needed(preq);
>> +
>> + ret = cdnsp_prepare_transfer(pdev, preq, trbs_per_td);
>> + if (ret)
>> + goto cleanup;
>> +
>> + /*
>> + * Set isoc specific data for the first TRB in a TD.
>> + * Prevent HW from getting the TRBs by keeping the cycle state
>> + * inverted in the first TDs isoc TRB.
>> + */
>> + field = TRB_TYPE(TRB_ISOC) | TRB_TLBPC(last_burst_pkt) |
>> + !start_cycle | TRB_SIA | TRB_TBC(burst_count);
>> +
>> + /* Fill the rest of the TRB fields, and remaining normal TRBs. */
>> + for (i = 0; i < trbs_per_td; i++) {
>> + u32 remainder;
>> +
>> + /* Calculate TRB length. */
>> + trb_buff_len = TRB_BUFF_LEN_UP_TO_BOUNDARY(addr);
>> + if (trb_buff_len > td_remain_len)
>> + trb_buff_len = td_remain_len;
>> +
>> + /* Set the TRB length, TD size, & interrupter fields. */
>> + remainder = cdnsp_td_remainder(pdev, running_total,
>> + trb_buff_len, td_len, preq,
>> + more_trbs_coming);
>> +
>> + length_field = TRB_LEN(trb_buff_len) | TRB_INTR_TARGET(0);
>> +
>> + /* Only first TRB is isoc, overwrite otherwise. */
>> + if (i) {
>> + field = TRB_TYPE(TRB_NORMAL) | ep_ring->cycle_state;
>> + length_field |= TRB_TD_SIZE(remainder);
>> + } else {
>> + length_field |= TRB_TD_SIZE_TBC(burst_count);
>> + }
>> +
>> + /* Only set interrupt on short packet for OUT EPs. */
>> + if (usb_endpoint_dir_out(preq->pep->endpoint.desc))
>> + field |= TRB_ISP;
>> +
>> + /* Set the chain bit for all except the last TRB. */
>> + if (i < trbs_per_td - 1) {
>> + more_trbs_coming = true;
>> + field |= TRB_CHAIN;
>> + } else {
>> + more_trbs_coming = false;
>> + preq->td.last_trb = ep_ring->enqueue;
>> + field |= TRB_IOC;
>> + }
>> +
>> + cdnsp_queue_trb(pdev, ep_ring, more_trbs_coming,
>> + lower_32_bits(addr), upper_32_bits(addr),
>> + length_field, field);
>> +
>> + running_total += trb_buff_len;
>> + addr += trb_buff_len;
>> + td_remain_len -= trb_buff_len;
>> + }
>> +
>> + /* Check TD length */
>> + if (running_total != td_len) {
>> + dev_err(pdev->dev, "ISOC TD length unmatch\n");
>> + ret = -EINVAL;
>> + goto cleanup;
>> + }
>> +
>> + cdnsp_giveback_first_trb(pdev, preq->pep, preq->request.stream_id,
>> + start_cycle, start_trb);
>> +
>> + return 0;
>> +
>> +cleanup:
>> + /* Clean up a partially enqueued isoc transfer. */
>> + list_del_init(&preq->td.td_list);
>> + ep_ring->num_tds--;
>> +
>> + /*
>> + * Use the first TD as a temporary variable to turn the TDs we've
>> + * queued into No-ops with a software-owned cycle bit.
>> + * That way the hardware won't accidentally start executing bogus TDs
>> + * when we partially overwrite them.
>> + * td->first_trb and td->start_seg are already set.
>> + */
>> + preq->td.last_trb = ep_ring->enqueue;
>> + /* Every TRB except the first & last will have its cycle bit flipped. */
>> + cdnsp_td_to_noop(pdev, ep_ring, &preq->td, true);
>> +
>> + /* Reset the ring enqueue back to the first TRB and its cycle bit. */
>> + ep_ring->enqueue = preq->td.first_trb;
>> + ep_ring->enq_seg = preq->td.start_seg;
>> + ep_ring->cycle_state = start_cycle;
>> + return ret;
>> +}
>> +
>> +int cdnsp_queue_isoc_tx_prepare(struct cdnsp_device *pdev,
>> + struct cdnsp_request *preq)
>> +{
>> + struct cdnsp_ring *ep_ring;
>> + u32 ep_state;
>> + int num_trbs;
>> + int ret;
>> +
>> + ep_ring = preq->pep->ring;
>> + ep_state = GET_EP_CTX_STATE(preq->pep->out_ctx);
>> + num_trbs = count_isoc_trbs_needed(preq);
>> +
>> + /*
>> + * Check the ring to guarantee there is enough room for the whole
>> + * request. Do not insert any td of the USB Request to the ring if the
>> + * check failed.
>> + */
>> + ret = cdnsp_prepare_ring(pdev, ep_ring, ep_state, num_trbs, GFP_ATOMIC);
>> + if (ret)
>> + return ret;
>> +
>> + return cdnsp_queue_isoc_tx(pdev, preq);
>> +}
>> +
>> +/**** Command Ring Operations ****/
>> +/*
>> + * Generic function for queuing a command TRB on the command ring.
>> + * Driver queue only one command to ring in the moment.
>> + */
>> +static void cdnsp_queue_command(struct cdnsp_device *pdev,
>> + u32 field1,
>> + u32 field2,
>> + u32 field3,
>> + u32 field4)
>> +{
>> + cdnsp_prepare_ring(pdev, pdev->cmd_ring, EP_STATE_RUNNING, 1,
>> + GFP_ATOMIC);
>> +
>> + pdev->cmd.command_trb = pdev->cmd_ring->enqueue;
>> +
>> + cdnsp_queue_trb(pdev, pdev->cmd_ring, false, field1, field2,
>> + field3, field4 | pdev->cmd_ring->cycle_state);
>> +}
>> +
>> +/* Queue a slot enable or disable request on the command ring */
>> +void cdnsp_queue_slot_control(struct cdnsp_device *pdev, u32 trb_type)
>> +{
>> + cdnsp_queue_command(pdev, 0, 0, 0, TRB_TYPE(trb_type) |
>> + SLOT_ID_FOR_TRB(pdev->slot_id));
>> +}
>> +
>> +/* Queue an address device command TRB */
>> +void cdnsp_queue_address_device(struct cdnsp_device *pdev,
>> + dma_addr_t in_ctx_ptr,
>> + enum cdnsp_setup_dev setup)
>> +{
>> + cdnsp_queue_command(pdev, lower_32_bits(in_ctx_ptr),
>> + upper_32_bits(in_ctx_ptr), 0,
>> + TRB_TYPE(TRB_ADDR_DEV) |
>> + SLOT_ID_FOR_TRB(pdev->slot_id) |
>> + (setup == SETUP_CONTEXT_ONLY ? TRB_BSR : 0));
>> +}
>> +
>> +/* Queue a reset device command TRB */
>> +void cdnsp_queue_reset_device(struct cdnsp_device *pdev)
>> +{
>> + cdnsp_queue_command(pdev, 0, 0, 0, TRB_TYPE(TRB_RESET_DEV) |
>> + SLOT_ID_FOR_TRB(pdev->slot_id));
>> +}
>> +
>> +/* Queue a configure endpoint command TRB */
>> +void cdnsp_queue_configure_endpoint(struct cdnsp_device *pdev,
>> + dma_addr_t in_ctx_ptr)
>> +{
>> + cdnsp_queue_command(pdev, lower_32_bits(in_ctx_ptr),
>> + upper_32_bits(in_ctx_ptr), 0,
>> + TRB_TYPE(TRB_CONFIG_EP) |
>> + SLOT_ID_FOR_TRB(pdev->slot_id));
>> +}
>> +
>> +/*
>> + * Suspend is set to indicate "Stop Endpoint Command" is being issued to stop
>> + * activity on an endpoint that is about to be suspended.
>> + */
>> +void cdnsp_queue_stop_endpoint(struct cdnsp_device *pdev, unsigned int ep_index)
>> +{
>> + cdnsp_queue_command(pdev, 0, 0, 0, SLOT_ID_FOR_TRB(pdev->slot_id) |
>> + EP_ID_FOR_TRB(ep_index) | TRB_TYPE(TRB_STOP_RING));
>> +}
>> +
>> +/* Set Transfer Ring Dequeue Pointer command. */
>> +void cdnsp_queue_new_dequeue_state(struct cdnsp_device *pdev,
>> + struct cdnsp_ep *pep,
>> + struct cdnsp_dequeue_state *deq_state)
>> +{
>> + u32 trb_stream_id = STREAM_ID_FOR_TRB(deq_state->stream_id);
>> + u32 trb_slot_id = SLOT_ID_FOR_TRB(pdev->slot_id);
>> + u32 type = TRB_TYPE(TRB_SET_DEQ);
>> + u32 trb_sct = 0;
>> + dma_addr_t addr;
>> +
>> + addr = cdnsp_trb_virt_to_dma(deq_state->new_deq_seg,
>> + deq_state->new_deq_ptr);
>> +
>> + if (deq_state->stream_id)
>> + trb_sct = SCT_FOR_TRB(SCT_PRI_TR);
>> +
>> + cdnsp_queue_command(pdev, lower_32_bits(addr) | trb_sct |
>> + deq_state->new_cycle_state, upper_32_bits(addr),
>> + trb_stream_id, trb_slot_id |
>> + EP_ID_FOR_TRB(pep->idx) | type);
>> +}
>> +
>> +void cdnsp_queue_reset_ep(struct cdnsp_device *pdev, unsigned int ep_index)
>> +{
>> + return cdnsp_queue_command(pdev, 0, 0, 0,
>> + SLOT_ID_FOR_TRB(pdev->slot_id) |
>> + EP_ID_FOR_TRB(ep_index) |
>> + TRB_TYPE(TRB_RESET_EP));
>> +}
>> +
>> +/*
>> + * Queue a halt endpoint request on the command ring.
>> + */
>> +void cdnsp_queue_halt_endpoint(struct cdnsp_device *pdev, unsigned int ep_index)
>> +{
>> + cdnsp_queue_command(pdev, 0, 0, 0, TRB_TYPE(TRB_HALT_ENDPOINT) |
>> + SLOT_ID_FOR_TRB(pdev->slot_id) |
>> + EP_ID_FOR_TRB(ep_index));
>> +}
>> +
>> +/*
>> + * Queue a flush endpoint request on the command ring.
>> + */
>> +void cdnsp_queue_flush_endpoint(struct cdnsp_device *pdev,
>> + unsigned int ep_index)
>> +{
>> + cdnsp_queue_command(pdev, 0, 0, 0, TRB_TYPE(TRB_FLUSH_ENDPOINT) |
>> + SLOT_ID_FOR_TRB(pdev->slot_id) |
>> + EP_ID_FOR_TRB(ep_index));
>> +}
>> +
>> +void cdnsp_force_header_wakeup(struct cdnsp_device *pdev, int intf_num)
>> +{
>> + u32 lo, mid;
>> +
>> + lo = TRB_FH_TO_PACKET_TYPE(TRB_FH_TR_PACKET) |
>> + TRB_FH_TO_DEVICE_ADDRESS(pdev->device_address);
>> + mid = TRB_FH_TR_PACKET_DEV_NOT |
>> + TRB_FH_TO_NOT_TYPE(TRB_FH_TR_PACKET_FUNCTION_WAKE) |
>> + TRB_FH_TO_INTERFACE(intf_num);
>> +
>> + cdnsp_queue_command(pdev, lo, mid, 0,
>> + TRB_TYPE(TRB_FORCE_HEADER) | SET_PORT_ID(2));
>> +}
>> --
>> 2.17.1
>>
>
>--
>
>Thanks,
>Peter Chen