/* winbond-840.c: A Linux PCI network adapter skeleton device driver. */
/*
Written 1998-2000 by Donald Becker.
This software may be used and distributed according to the terms of
the GNU General Public License (GPL), incorporated herein by reference.
Drivers based on or derived from this code fall under the GPL and must
retain the authorship, copyright and license notice. This file is not
a complete program and may only be used when the entire operating
system is licensed under the GPL.
The author may be reached as [email protected], or C/O
Scyld Computing Corporation
410 Severn Ave., Suite 210
Annapolis MD 21403
Support and updates available at
http://www.scyld.com/network/drivers.html
Do not remove the copyright infomation.
Do not change the version information unless an improvement has been made.
Merely removing my name, as Compex has done in the past, does not count
as an improvement.
*/
/* These identify the driver base version and may not be removed. */
static const char version1[] =
"winbond-840.c:v1.01 5/15/2000 Donald Becker <[email protected]>\n";
static const char version2[] =
" http://www.scyld.com/network/drivers.html\n";
/* Automatically extracted configuration info:
probe-func: winbond840_probe
config-in: tristate 'Winbond W89c840 Ethernet support' CONFIG_WINBOND_840
c-help-name: Winbond W89c840 PCI Ethernet support
c-help-symbol: CONFIG_WINBOND_840
c-help: This driver is for the Winbond W89c840 chip. It also works with
c-help: the TX9882 chip on the Compex RL100-ATX board.
c-help: More specific information and updates are available from
c-help: http://www.scyld.com/network/drivers.html
*/
/* The user-configurable values.
These may be modified when a driver module is loaded.*/
static int debug = 1; /* 1 normal messages, 0 quiet .. 7 verbose. */
static int max_interrupt_work = 20;
/* Maximum number of multicast addresses to filter (vs. Rx-all-multicast).
The '840 uses a 64 element hash table based on the Ethernet CRC. */
static int multicast_filter_limit = 32;
/* Set the copy breakpoint for the copy-only-tiny-frames scheme.
Setting to > 1518 effectively disables this feature. */
static int rx_copybreak = 0;
/* Used to pass the media type, etc.
Both 'options[]' and 'full_duplex[]' should exist for driver
interoperability.
The media type is usually passed in 'options[]'.
*/
#define MAX_UNITS 8 /* More are supported, limit only on options */
static int options[MAX_UNITS] = {-1, -1, -1, -1, -1, -1, -1, -1};
static int full_duplex[MAX_UNITS] = {-1, -1, -1, -1, -1, -1, -1, -1};
/* Operational parameters that are set at compile time. */
/* Keep the ring sizes a power of two for compile efficiency.
The compiler will convert <unsigned>'%'<2^N> into a bit mask.
Making the Tx ring too large decreases the effectiveness of channel
bonding and packet priority.
There are no ill effects from too-large receive rings. */
#define TX_RING_SIZE 16
#define TX_QUEUE_LEN 10 /* Limit ring entries actually used. */
#define RX_RING_SIZE 32
/* The presumed FIFO size for working around the Tx-FIFO-overflow bug.
To avoid overflowing we don't queue again until we have room for a
full-size packet.
*/
#define TX_FIFO_SIZE (2048)
#define TX_BUG_FIFO_LIMIT (TX_FIFO_SIZE-1514-16)
/* Operational parameters that usually are not changed. */
/* Time in jiffies before concluding the transmitter is hung. */
#define TX_TIMEOUT (2*HZ)
#define PKT_BUF_SZ 1536 /* Size of each temporary Rx buffer.*/
#ifndef __KERNEL__
#define __KERNEL__
#endif
#if !defined(__OPTIMIZE__)
#warning You must compile this file with the correct options!
#warning See the last lines of the source file.
#error You must compile this driver with "-O".
#endif
/* Include files, designed to support most kernel versions 2.0.0 and later. */
#include <linux/config.h>
#if defined(CONFIG_SMP) && ! defined(__SMP__)
#define __SMP__
#endif
#if defined(CONFIG_MODVERSIONS) && ! defined(MODVERSIONS)
#define MODVERSIONS
#endif
#include <linux/version.h>
#include <linux/module.h>
#if LINUX_VERSION_CODE < 0x20300 && defined(MODVERSIONS)
#include <linux/modversions.h>
#endif
#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/timer.h>
#include <linux/errno.h>
#include <linux/ioport.h>
#include <linux/malloc.h>
#include <linux/interrupt.h>
#include <linux/pci.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include <asm/processor.h> /* Processor type for cache alignment. */
#include <asm/bitops.h>
#include <asm/io.h>
#ifdef INLINE_PCISCAN
#include "k_compat.h"
#else
#include "pci-scan.h"
#include "kern_compat.h"
#endif
/* Condensed operations for readability.
The compatibility defines are in kern_compat.h */
#define virt_to_le32desc(addr) cpu_to_le32(virt_to_bus(addr))
#define le32desc_to_virt(addr) bus_to_virt(le32_to_cpu(addr))
#if (LINUX_VERSION_CODE >= 0x20100) && defined(MODULE)
char kernel_version[] = UTS_RELEASE;
#endif
MODULE_AUTHOR("Donald Becker <[email protected]>");
MODULE_DESCRIPTION("Winbond W89c840 Ethernet driver");
MODULE_PARM(max_interrupt_work, "i");
MODULE_PARM(debug, "i");
MODULE_PARM(rx_copybreak, "i");
MODULE_PARM(multicast_filter_limit, "i");
MODULE_PARM(options, "1-" __MODULE_STRING(MAX_UNITS) "i");
MODULE_PARM(full_duplex, "1-" __MODULE_STRING(MAX_UNITS) "i");
/*
Theory of Operation
I. Board Compatibility
This driver is for the Winbond w89c840 chip.
II. Board-specific settings
None.
III. Driver operation
This chip is very similar to the Digital 21*4* "Tulip" family. The first
twelve registers and the descriptor format are nearly identical. Read a
Tulip manual for operational details.
A significant difference is that the multicast filter and station address are
stored in registers rather than loaded through a pseudo-transmit packet.
Unlike the Tulip, transmit buffers are limited to 1KB. To transmit a
full-sized packet we must use both data buffers in a descriptor. Thus the
driver uses ring mode where descriptors are implicitly sequential in memory,
rather than using the second descriptor address as a chain pointer to
subsequent descriptors.
IV. Notes
If you are going to almost clone a Tulip, why not go all the way and avoid
the need for a new driver?
IVb. References
http://www.scyld.com/expert/100mbps.html
http://www.scyld.com/expert/NWay.html
http://www.winbond.com.tw/
IVc. Errata
A horrible bug exists in the transmit FIFO. Apparently the chip doesn't
correctly detect a full FIFO, and queuing more than 2048 bytes may result in
silent data corruption.
*/
/*
PCI probe table.
*/
static void *w840_probe1(struct pci_dev *pdev, void *init_dev,
long ioaddr, int irq, int chip_idx, int find_cnt);
enum chip_capability_flags {CanHaveMII=1, HasBrokenTx=2};
#ifdef USE_IO_OPS
#define W840_FLAGS (PCI_USES_IO | PCI_ADDR0 | PCI_USES_MASTER)
#else
#define W840_FLAGS (PCI_USES_MEM | PCI_ADDR1 | PCI_USES_MASTER)
#endif
static struct pci_id_info pci_id_tbl[] = {
{"Winbond W89c840", { 0x08401050, 0xffffffff, },
W840_FLAGS, 128, CanHaveMII | HasBrokenTx},
{"Compex RL100-ATX", { 0x201111F6, 0xffffffff,},
W840_FLAGS, 128, CanHaveMII | HasBrokenTx},
{0,}, /* 0 terminated list. */
};
struct drv_id_info winbond840_drv_id = {
"winbond-840", 0, PCI_CLASS_NETWORK_ETHERNET<<8, pci_id_tbl, w840_probe1 };
/* This driver was written to use PCI memory space, however some x86 systems
work only with I/O space accesses. Pass -DUSE_IO_OPS to use PCI I/O space
accesses instead of memory space. */
#ifdef USE_IO_OPS
#undef readb
#undef readw
#undef readl
#undef writeb
#undef writew
#undef writel
#define readb inb
#define readw inw
#define readl inl
#define writeb outb
#define writew outw
#define writel outl
#endif
/* Offsets to the Command and Status Registers, "CSRs".
While similar to the Tulip, these registers are longword aligned.
Note: It's not useful to define symbolic names for every register bit in
the device. The name can only partially document the semantics and make
the driver longer and more difficult to read.
*/
enum w840_offsets {
PCIBusCfg=0x00, TxStartDemand=0x04, RxStartDemand=0x08,
RxRingPtr=0x0C, TxRingPtr=0x10,
IntrStatus=0x14, NetworkConfig=0x18, IntrEnable=0x1C,
RxMissed=0x20, EECtrl=0x24, MIICtrl=0x24, BootRom=0x28, GPTimer=0x2C,
CurRxDescAddr=0x30, CurRxBufAddr=0x34, /* Debug use */
MulticastFilter0=0x38, MulticastFilter1=0x3C, StationAddr=0x40,
CurTxDescAddr=0x4C, CurTxBufAddr=0x50,
};
/* Bits in the interrupt status/enable registers. */
/* The bits in the Intr Status/Enable registers, mostly interrupt sources. */
enum intr_status_bits {
NormalIntr=0x10000, AbnormalIntr=0x8000,
IntrPCIErr=0x2000, TimerInt=0x800,
IntrRxDied=0x100, RxNoBuf=0x80, IntrRxDone=0x40,
TxFIFOUnderflow=0x20, RxErrIntr=0x10,
TxIdle=0x04, IntrTxStopped=0x02, IntrTxDone=0x01,
};
/* Bits in the NetworkConfig register. */
enum rx_mode_bits {
AcceptErr=0x80, AcceptRunt=0x40,
AcceptBroadcast=0x20, AcceptMulticast=0x10,
AcceptAllPhys=0x08, AcceptMyPhys=0x02,
};
enum mii_reg_bits {
MDIO_ShiftClk=0x10000, MDIO_DataIn=0x80000, MDIO_DataOut=0x20000,
MDIO_EnbOutput=0x40000, MDIO_EnbIn = 0x00000,
};
/* The Tulip Rx and Tx buffer descriptors. */
struct w840_rx_desc {
s32 status;
s32 length;
u32 buffer1;
u32 next_desc;
};
struct w840_tx_desc {
s32 status;
s32 length;
u32 buffer1, buffer2; /* We use only buffer 1. */
};
/* Bits in network_desc.status */
enum desc_status_bits {
DescOwn=0x80000000, DescEndRing=0x02000000, DescUseLink=0x01000000,
DescWholePkt=0x60000000, DescStartPkt=0x20000000, DescEndPkt=0x40000000,
DescIntr=0x80000000,
};
#define PRIV_ALIGN 15 /* Required alignment mask */
struct netdev_private {
/* Descriptor rings first for alignment. */
struct w840_rx_desc rx_ring[RX_RING_SIZE];
struct w840_tx_desc tx_ring[TX_RING_SIZE];
struct net_device *next_module; /* Link for devices of this type. */
void *priv_addr; /* Unaligned address for kfree */
const char *product_name;
/* The addresses of receive-in-place skbuffs. */
struct sk_buff* rx_skbuff[RX_RING_SIZE];
/* The saved address of a sent-in-place packet/buffer, for later free(). */
struct sk_buff* tx_skbuff[TX_RING_SIZE];
struct net_device_stats stats;
struct timer_list timer; /* Media monitoring timer. */
/* Frequently used values: keep some adjacent for cache effect. */
int chip_id, drv_flags;
struct pci_dev *pci_dev;
int csr6;
struct w840_rx_desc *rx_head_desc;
unsigned int cur_rx, dirty_rx; /* Producer/consumer ring indices */
unsigned int rx_buf_sz; /* Based on MTU+slack. */
unsigned int cur_tx, dirty_tx;
int tx_q_bytes;
unsigned int tx_full:1; /* The Tx queue is full. */
/* These values are keep track of the transceiver/media in use. */
unsigned int full_duplex:1; /* Full-duplex operation requested. */
unsigned int duplex_lock:1;
unsigned int medialock:1; /* Do not sense media. */
unsigned int default_port:4; /* Last dev->if_port value. */
/* MII transceiver section. */
int mii_cnt; /* MII device addresses. */
u16 advertising; /* NWay media advertisement */
unsigned char phys[2]; /* MII device addresses. */
};
static int eeprom_read(long ioaddr, int location);
static int mdio_read(struct net_device *dev, int phy_id, int location);
static void mdio_write(struct net_device *dev, int phy_id, int location, int value);
static int netdev_open(struct net_device *dev);
static void check_duplex(struct net_device *dev);
static void netdev_timer(unsigned long data);
static void tx_timeout(struct net_device *dev);
static void init_ring(struct net_device *dev);
static int start_tx(struct sk_buff *skb, struct net_device *dev);
static void intr_handler(int irq, void *dev_instance, struct pt_regs *regs);
static void netdev_error(struct net_device *dev, int intr_status);
static int netdev_rx(struct net_device *dev);
static void netdev_error(struct net_device *dev, int intr_status);
static inline unsigned ether_crc(int length, unsigned char *data);
static void set_rx_mode(struct net_device *dev);
static struct net_device_stats *get_stats(struct net_device *dev);
static int mii_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
static int netdev_close(struct net_device *dev);
/* A list of our installed devices, for removing the driver module. */
static struct net_device *root_net_dev = NULL;
static void *w840_probe1(struct pci_dev *pdev, void *init_dev,
long ioaddr, int irq, int chip_idx, int find_cnt)
{
struct net_device *dev;
struct netdev_private *np;
void *priv_mem;
int i, option = find_cnt < MAX_UNITS ? options[find_cnt] : 0;
dev = init_etherdev(init_dev, 0);
printk(KERN_INFO "%s: %s at 0x%lx, ",
dev->name, pci_id_tbl[chip_idx].name, ioaddr);
/* Warning: broken for big-endian machines. */
for (i = 0; i < 3; i++)
((u16 *)dev->dev_addr)[i] = le16_to_cpu(eeprom_read(ioaddr, i));
for (i = 0; i < 5; i++)
printk("%2.2x:", dev->dev_addr[i]);
printk("%2.2x, IRQ %d.\n", dev->dev_addr[i], irq);
priv_mem = kmalloc(sizeof(*np) + PRIV_ALIGN, GFP_KERNEL);
/* Out of memory is very unlikely. */
if (priv_mem == NULL)
return NULL;
#ifdef USE_IO_OPS
request_region(ioaddr, pci_tbl[chip_idx].io_size, dev->name);
#endif
/* Reset the chip to erase previous misconfiguration.
No hold time required! */
writel(0x00000001, ioaddr + PCIBusCfg);
dev->base_addr = ioaddr;
dev->irq = irq;
/* The descriptor lists must be aligned. */
dev->priv = np = (void *)(((long)priv_mem + PRIV_ALIGN) & ~PRIV_ALIGN);
memset(np, 0, sizeof(*np));
np->priv_addr = priv_mem;
np->next_module = root_net_dev;
root_net_dev = dev;
np->pci_dev = pdev;
np->chip_id = chip_idx;
np->drv_flags = pci_id_tbl[chip_idx].drv_flags;
if (dev->mem_start)
option = dev->mem_start;
/* The lower four bits are the media type. */
if (option > 0) {
if (option & 0x200)
np->full_duplex = 1;
np->default_port = option & 15;
if (np->default_port)
np->medialock = 1;
}
if (find_cnt < MAX_UNITS && full_duplex[find_cnt] > 0)
np->full_duplex = 1;
if (np->full_duplex)
np->duplex_lock = 1;
/* The chip-specific entries in the device structure. */
dev->open = &netdev_open;
dev->hard_start_xmit = &start_tx;
dev->stop = &netdev_close;
dev->get_stats = &get_stats;
dev->set_multicast_list = &set_rx_mode;
dev->do_ioctl = &mii_ioctl;
if (np->drv_flags & CanHaveMII) {
int phy, phy_idx = 0;
for (phy = 1; phy < 32 && phy_idx < 4; phy++) {
int mii_status = mdio_read(dev, phy, 1);
if (mii_status != 0xffff && mii_status != 0x0000) {
np->phys[phy_idx++] = phy;
np->advertising = mdio_read(dev, phy, 4);
printk(KERN_INFO "%s: MII PHY found at address %d, status "
"0x%4.4x advertising %4.4x.\n",
dev->name, phy, mii_status, np->advertising);
}
}
np->mii_cnt = phy_idx;
if (phy_idx == 0) {
printk(KERN_WARNING "%s: MII PHY not found -- this device may "
"not operate correctly.\n", dev->name);
}
}
return dev;
}
/* Read the EEPROM and MII Management Data I/O (MDIO) interfaces. These are
often serial bit streams generated by the host processor.
The example below is for the common 93c46 EEPROM, 64 16 bit words. */
/* Delay between EEPROM clock transitions.
No extra delay is needed with 33Mhz PCI, but future 66Mhz access may need
a delay. Note that pre-2.0.34 kernels had a cache-alignment bug that
made udelay() unreliable.
The old method of using an ISA access as a delay, __SLOW_DOWN_IO__, is
depricated.
*/
#define eeprom_delay(ee_addr) readl(ee_addr)
enum EEPROM_Ctrl_Bits {
EE_ShiftClk=0x02, EE_Write0=0x801, EE_Write1=0x805,
EE_ChipSelect=0x801, EE_DataIn=0x08,
};
/* The EEPROM commands include the alway-set leading bit. */
enum EEPROM_Cmds {
EE_WriteCmd=(5 << 6), EE_ReadCmd=(6 << 6), EE_EraseCmd=(7 << 6),
};
static int eeprom_read(long addr, int location)
{
int i;
int retval = 0;
int ee_addr = addr + EECtrl;
int read_cmd = location | EE_ReadCmd;
writel(EE_ChipSelect, ee_addr);
/* Shift the read command bits out. */
for (i = 10; i >= 0; i--) {
short dataval = (read_cmd & (1 << i)) ? EE_Write1 : EE_Write0;
writel(dataval, ee_addr);
eeprom_delay(ee_addr);
writel(dataval | EE_ShiftClk, ee_addr);
eeprom_delay(ee_addr);
}
writel(EE_ChipSelect, ee_addr);
for (i = 16; i > 0; i--) {
writel(EE_ChipSelect | EE_ShiftClk, ee_addr);
eeprom_delay(ee_addr);
retval = (retval << 1) | ((readl(ee_addr) & EE_DataIn) ? 1 : 0);
writel(EE_ChipSelect, ee_addr);
eeprom_delay(ee_addr);
}
/* Terminate the EEPROM access. */
writel(0, ee_addr);
return retval;
}
/* MII transceiver control section.
Read and write the MII registers using software-generated serial
MDIO protocol. See the MII specifications or DP83840A data sheet
for details.
The maximum data clock rate is 2.5 Mhz. The minimum timing is usually
met by back-to-back 33Mhz PCI cycles. */
#define mdio_delay(mdio_addr) readl(mdio_addr)
/* Set iff a MII transceiver on any interface requires mdio preamble.
This only set with older tranceivers, so the extra
code size of a per-interface flag is not worthwhile. */
static char mii_preamble_required = 1;
#define MDIO_WRITE0 (MDIO_EnbOutput)
#define MDIO_WRITE1 (MDIO_DataOut | MDIO_EnbOutput)
/* Generate the preamble required for initial synchronization and
a few older transceivers. */
static void mdio_sync(long mdio_addr)
{
int bits = 32;
/* Establish sync by sending at least 32 logic ones. */
while (--bits >= 0) {
writel(MDIO_WRITE1, mdio_addr);
mdio_delay(mdio_addr);
writel(MDIO_WRITE1 | MDIO_ShiftClk, mdio_addr);
mdio_delay(mdio_addr);
}
}
static int mdio_read(struct net_device *dev, int phy_id, int location)
{
long mdio_addr = dev->base_addr + MIICtrl;
int mii_cmd = (0xf6 << 10) | (phy_id << 5) | location;
int i, retval = 0;
if (mii_preamble_required)
mdio_sync(mdio_addr);
/* Shift the read command bits out. */
for (i = 15; i >= 0; i--) {
int dataval = (mii_cmd & (1 << i)) ? MDIO_WRITE1 : MDIO_WRITE0;
writel(dataval, mdio_addr);
mdio_delay(mdio_addr);
writel(dataval | MDIO_ShiftClk, mdio_addr);
mdio_delay(mdio_addr);
}
/* Read the two transition, 16 data, and wire-idle bits. */
for (i = 20; i > 0; i--) {
writel(MDIO_EnbIn, mdio_addr);
mdio_delay(mdio_addr);
retval = (retval << 1) | ((readl(mdio_addr) & MDIO_DataIn) ? 1 : 0);
writel(MDIO_EnbIn | MDIO_ShiftClk, mdio_addr);
mdio_delay(mdio_addr);
}
return (retval>>1) & 0xffff;
}
static void mdio_write(struct net_device *dev, int phy_id, int location, int value)
{
struct netdev_private *np = (struct netdev_private *)dev->priv;
long mdio_addr = dev->base_addr + MIICtrl;
int mii_cmd = (0x5002 << 16) | (phy_id << 23) | (location<<18) | value;
int i;
if (location == 4 && phy_id == np->phys[0])
np->advertising = value;
if (mii_preamble_required)
mdio_sync(mdio_addr);
/* Shift the command bits out. */
for (i = 31; i >= 0; i--) {
int dataval = (mii_cmd & (1 << i)) ? MDIO_WRITE1 : MDIO_WRITE0;
writel(dataval, mdio_addr);
mdio_delay(mdio_addr);
writel(dataval | MDIO_ShiftClk, mdio_addr);
mdio_delay(mdio_addr);
}
/* Clear out extra bits. */
for (i = 2; i > 0; i--) {
writel(MDIO_EnbIn, mdio_addr);
mdio_delay(mdio_addr);
writel(MDIO_EnbIn | MDIO_ShiftClk, mdio_addr);
mdio_delay(mdio_addr);
}
return;
}
static int netdev_open(struct net_device *dev)
{
struct netdev_private *np = (struct netdev_private *)dev->priv;
long ioaddr = dev->base_addr;
int i;
writel(0x00000001, ioaddr + PCIBusCfg); /* Reset */
MOD_INC_USE_COUNT;
if (request_irq(dev->irq, &intr_handler, SA_SHIRQ, dev->name, dev)) {
MOD_DEC_USE_COUNT;
return -EAGAIN;
}
if (debug > 1)
printk(KERN_DEBUG "%s: w89c840_open() irq %d.\n",
dev->name, dev->irq);
init_ring(dev);
writel(virt_to_bus(np->rx_ring), ioaddr + RxRingPtr);
writel(virt_to_bus(np->tx_ring), ioaddr + TxRingPtr);
for (i = 0; i < 6; i++)
writeb(dev->dev_addr[i], ioaddr + StationAddr + i);
/* Initialize other registers. */
/* Configure the PCI bus bursts and FIFO thresholds.
486: Set 8 longword cache alignment, 8 longword burst.
586: Set 16 longword cache alignment, no burst limit.
Cache alignment bits 15:14 Burst length 13:8
0000 <not allowed> 0000 align to cache 0800 8 longwords
4000 8 longwords 0100 1 longword 1000 16 longwords
8000 16 longwords 0200 2 longwords 2000 32 longwords
C000 32 longwords 0400 4 longwords
Wait the specified 50 PCI cycles after a reset by initializing
Tx and Rx queues and the address filter list. */
#if defined(__powerpc__) /* Big-endian */
writel(0x00100080 | 0xE010, ioaddr + PCIBusCfg);
#elif defined(__alpha__)
writel(0xE010, ioaddr + PCIBusCfg);
#elif defined(__i386__)
#if defined(MODULE)
writel(0xE010, ioaddr + PCIBusCfg);
#else
/* When not a module we can work around broken '486 PCI boards. */
#if (LINUX_VERSION_CODE > 0x2014c)
#define x86 boot_cpu_data.x86
#endif
writel((x86 <= 4 ? 0x4810 : 0xE010), ioaddr + PCIBusCfg);
if (x86 <= 4)
printk(KERN_INFO "%s: This is a 386/486 PCI system, setting cache "
"alignment to %x.\n", dev->name,
(x86 <= 4 ? 0x4810 : 0x8010));
#endif
#else
writel(0xE010, ioaddr + PCIBusCfg);
#warning Processor architecture undefined!
#endif
if (dev->if_port == 0)
dev->if_port = np->default_port;
dev->tbusy = 0;
dev->interrupt = 0;
writel(0, ioaddr + RxStartDemand);
np->csr6 = 0x20022002;
check_duplex(dev);
set_rx_mode(dev);
dev->start = 1;
/* Clear and Enable interrupts by setting the interrupt mask. */
writel(0x1A0F5, ioaddr + IntrStatus);
writel(0x1A0F5, ioaddr + IntrEnable);
if (debug > 2)
printk(KERN_DEBUG "%s: Done netdev_open().\n", dev->name);
/* Set the timer to check for link beat. */
init_timer(&np->timer);
np->timer.expires = jiffies + 3*HZ;
np->timer.data = (unsigned long)dev;
np->timer.function = &netdev_timer; /* timer handler */
add_timer(&np->timer);
return 0;
}
static void check_duplex(struct net_device *dev)
{
struct netdev_private *np = (struct netdev_private *)dev->priv;
int mii_reg5 = mdio_read(dev, np->phys[0], 5);
int negotiated = mii_reg5 & np->advertising;
int duplex;
if (np->duplex_lock || mii_reg5 == 0xffff)
return;
duplex = (negotiated & 0x0100) || (negotiated & 0x01C0) == 0x0040;
if (np->full_duplex != duplex) {
np->full_duplex = duplex;
if (debug)
printk(KERN_INFO "%s: Setting %s-duplex based on MII #%d "
"negotiated capability %4.4x.\n", dev->name,
duplex ? "full" : "half", np->phys[0], negotiated);
np->csr6 &= ~0x200;
np->csr6 |= duplex ? 0x200 : 0;
}
}
static void netdev_timer(unsigned long data)
{
struct net_device *dev = (struct net_device *)data;
struct netdev_private *np = (struct netdev_private *)dev->priv;
long ioaddr = dev->base_addr;
int next_tick = 10*HZ;
int old_csr6 = np->csr6;
if (debug > 2)
printk(KERN_DEBUG "%s: Media selection timer tick, status %8.8x "
"config %8.8x.\n",
dev->name, (int)readl(ioaddr + IntrStatus),
(int)readl(ioaddr + NetworkConfig));
if (test_bit(0, (void*)&dev->tbusy) &&
np->cur_tx - np->dirty_tx > 1 &&
(jiffies - dev->trans_start) > TX_TIMEOUT) {
tx_timeout(dev);
}
check_duplex(dev);
if (np->csr6 != old_csr6) {
writel(np->csr6 & ~0x0002, ioaddr + NetworkConfig);
writel(np->csr6 | 0x2002, ioaddr + NetworkConfig);
}
np->timer.expires = jiffies + next_tick;
add_timer(&np->timer);
}
static void tx_timeout(struct net_device *dev)
{
struct netdev_private *np = (struct netdev_private *)dev->priv;
long ioaddr = dev->base_addr;
printk(KERN_WARNING "%s: Transmit timed out, status %8.8x,"
" resetting...\n", dev->name, (int)readl(ioaddr + IntrStatus));
#ifndef __alpha__
{
int i;
printk(KERN_DEBUG " Rx ring %8.8x: ", (int)np->rx_ring);
for (i = 0; i < RX_RING_SIZE; i++)
printk(" %8.8x", (unsigned int)np->rx_ring[i].status);
printk("\n"KERN_DEBUG" Tx ring %8.8x: ", (int)np->tx_ring);
for (i = 0; i < TX_RING_SIZE; i++)
printk(" %4.4x", np->tx_ring[i].status);
printk("\n");
}
#endif
/* Perhaps we should reinitialize the hardware here. Just trigger a
Tx demand for now. */
writel(0, ioaddr + TxStartDemand);
dev->if_port = 0;
/* Stop and restart the chip's Tx processes . */
dev->trans_start = jiffies;
np->stats.tx_errors++;
return;
}
/* Initialize the Rx and Tx rings, along with various 'dev' bits. */
static void init_ring(struct net_device *dev)
{
struct netdev_private *np = (struct netdev_private *)dev->priv;
int i;
np->tx_full = 0;
np->tx_q_bytes = np->cur_rx = np->cur_tx = 0;
np->dirty_rx = np->dirty_tx = 0;
np->rx_buf_sz = (dev->mtu <= 1500 ? PKT_BUF_SZ : dev->mtu + 32);
np->rx_head_desc = &np->rx_ring[0];
/* Initial all Rx descriptors. */
for (i = 0; i < RX_RING_SIZE; i++) {
np->rx_ring[i].length = cpu_to_le32(np->rx_buf_sz);
np->rx_ring[i].status = 0;
np->rx_ring[i].next_desc = virt_to_le32desc(&np->rx_ring[i+1]);
np->rx_skbuff[i] = 0;
}
/* Mark the last entry as wrapping the ring. */
np->rx_ring[i-1].length |= cpu_to_le32(DescEndRing);
np->rx_ring[i-1].next_desc = virt_to_le32desc(&np->rx_ring[0]);
/* Fill in the Rx buffers. Handle allocation failure gracefully. */
for (i = 0; i < RX_RING_SIZE; i++) {
struct sk_buff *skb = dev_alloc_skb(np->rx_buf_sz);
np->rx_skbuff[i] = skb;
if (skb == NULL)
break;
skb->dev = dev; /* Mark as being used by this device. */
np->rx_ring[i].buffer1 = virt_to_le32desc(skb->tail);
np->rx_ring[i].status = cpu_to_le32(DescOwn | DescIntr);
}
np->dirty_rx = (unsigned int)(i - RX_RING_SIZE);
for (i = 0; i < TX_RING_SIZE; i++) {
np->tx_skbuff[i] = 0;
np->tx_ring[i].status = 0;
}
return;
}
static int start_tx(struct sk_buff *skb, struct net_device *dev)
{
struct netdev_private *np = (struct netdev_private *)dev->priv;
unsigned entry;
/* Block a timer-based transmit from overlapping. This could better be
done with atomic_swap(1, dev->tbusy), but set_bit() works as well. */
if (test_and_set_bit(0, (void*)&dev->tbusy) != 0) {
if (jiffies - dev->trans_start > TX_TIMEOUT)
tx_timeout(dev);
return 1;
}
/* Caution: the write order is important here, set the field
with the "ownership" bits last. */
/* Calculate the next Tx descriptor entry. */
entry = np->cur_tx % TX_RING_SIZE;
np->tx_skbuff[entry] = skb;
np->tx_ring[entry].buffer1 = virt_to_le32desc(skb->data);
#define one_buffer
#define BPT 1022
#if defined(one_buffer)
np->tx_ring[entry].length = cpu_to_le32(DescWholePkt | skb->len);
if (entry >= TX_RING_SIZE-1) /* Wrap ring */
np->tx_ring[entry].length |= cpu_to_le32(DescIntr | DescEndRing);
np->tx_ring[entry].status = cpu_to_le32(DescOwn);
np->cur_tx++;
#elif defined(two_buffer)
if (skb->len > BPT) {
unsigned int entry1 = ++np->cur_tx % TX_RING_SIZE;
np->tx_ring[entry].length = cpu_to_le32(DescStartPkt | BPT);
np->tx_ring[entry1].length = cpu_to_le32(DescEndPkt | (skb->len - BPT));
np->tx_ring[entry1].buffer1 = virt_to_le32desc((skb->data) + BPT);
np->tx_ring[entry1].status = cpu_to_le32(DescOwn);
np->tx_ring[entry].status = cpu_to_le32(DescOwn);
if (entry >= TX_RING_SIZE-1)
np->tx_ring[entry].length |= cpu_to_le32(DescIntr|DescEndRing);
else if (entry1 >= TX_RING_SIZE-1)
np->tx_ring[entry1].length |= cpu_to_le32(DescIntr|DescEndRing);
np->cur_tx++;
} else {
np->tx_ring[entry].length = cpu_to_le32(DescWholePkt | skb->len);
if (entry >= TX_RING_SIZE-1) /* Wrap ring */
np->tx_ring[entry].length |= cpu_to_le32(DescIntr | DescEndRing);
np->tx_ring[entry].status = cpu_to_le32(DescOwn);
np->cur_tx++;
}
#elif defined(split_buffer)
{
/* Work around the Tx-FIFO-full bug by splitting our transmit packet
into two pieces, the first which may be loaded without overflowing
the FIFO, and the second which contains the remainder of the
packet. When we get a Tx-done interrupt that frees enough room
in the FIFO we mark the remainder of the packet as loadable.
This has the problem that the Tx descriptors are written both
here and in the interrupt handler.
*/
int buf1size = TX_FIFO_SIZE - np->tx_q_bytes;
int buf2size = skb->len - buf1size;
if (buf2size <= 0) { /* We fit into one descriptor. */
np->tx_ring[entry].length = cpu_to_le32(DescWholePkt | skb->len);
} else { /* We must use two descriptors. */
unsigned int entry2;
np->tx_ring[entry].length =
cpu_to_le32(DescIntr | DescStartPkt | buf1size);
if (entry >= TX_RING_SIZE-1) { /* Wrap ring */
np->tx_ring[entry].length |= cpu_to_le32(DescEndRing);
entry2 = 0;
} else
entry2 = entry + 1;
np->cur_tx++;
np->tx_ring[entry2].buffer1 =
virt_to_le32desc(skb->data + buf1size);
np->tx_ring[entry2].length = cpu_to_le32(DescEndPkt | buf2size);
if (entry2 >= TX_RING_SIZE-1) /* Wrap ring */
np->tx_ring[entry2].length |= cpu_to_le32(DescEndRing);
}
np->tx_ring[entry].status = cpu_to_le32(DescOwn);
np->cur_tx++;
}
#endif
np->tx_q_bytes += skb->len;
writel(0, dev->base_addr + TxStartDemand);
/* Work around horrible bug in the chip by marking the queue as full
when we do not have FIFO room for a maximum sized packet. */
if (np->cur_tx - np->dirty_tx > TX_QUEUE_LEN)
np->tx_full = 1;
else if ((np->drv_flags & HasBrokenTx)
&& np->tx_q_bytes > TX_BUG_FIFO_LIMIT)
np->tx_full = 1;
else
clear_bit(0, (void*)&dev->tbusy); /* Typical path */
dev->trans_start = jiffies;
if (debug > 4) {
printk(KERN_DEBUG "%s: Transmit frame #%d queued in slot %d.\n",
dev->name, np->cur_tx, entry);
}
return 0;
}
/* The interrupt handler does all of the Rx thread work and cleans up
after the Tx thread. */
static void intr_handler(int irq, void *dev_instance, struct pt_regs *rgs)
{
struct net_device *dev = (struct net_device *)dev_instance;
struct netdev_private *np = (struct netdev_private *)dev->priv;
long ioaddr = dev->base_addr;
int work_limit = max_interrupt_work;
#if defined(__i386__)
/* A lock to prevent simultaneous entry bug on Intel SMP machines. */
if (test_and_set_bit(0, (void*)&dev->interrupt)) {
printk(KERN_ERR"%s: SMP simultaneous entry of an interrupt handler.\n",
dev->name);
dev->interrupt = 0; /* Avoid halting machine. */
return;
}
#endif
do {
u32 intr_status = readl(ioaddr + IntrStatus);
/* Acknowledge all of the current interrupt sources ASAP. */
writel(intr_status & 0x001ffff, ioaddr + IntrStatus);
if (debug > 4)
printk(KERN_DEBUG "%s: Interrupt, status %4.4x.\n",
dev->name, intr_status);
if ((intr_status & (NormalIntr|AbnormalIntr)) == 0)
break;
if (intr_status & (IntrRxDone | RxNoBuf))
netdev_rx(dev);
for (; np->cur_tx - np->dirty_tx > 0; np->dirty_tx++) {
int entry = np->dirty_tx % TX_RING_SIZE;
int tx_status = le32_to_cpu(np->tx_ring[entry].status);
if (tx_status < 0)
break;
if (tx_status & 0x8000) { /* There was an error, log it. */
#ifndef final_version
if (debug > 1)
printk(KERN_DEBUG "%s: Transmit error, Tx status %8.8x.\n",
dev->name, tx_status);
#endif
np->stats.tx_errors++;
if (tx_status & 0x0104) np->stats.tx_aborted_errors++;
if (tx_status & 0x0C80) np->stats.tx_carrier_errors++;
if (tx_status & 0x0200) np->stats.tx_window_errors++;
if (tx_status & 0x0002) np->stats.tx_fifo_errors++;
if ((tx_status & 0x0080) && np->full_duplex == 0)
np->stats.tx_heartbeat_errors++;
#ifdef ETHER_STATS
if (tx_status & 0x0100) np->stats.collisions16++;
#endif
} else {
#ifdef ETHER_STATS
if (tx_status & 0x0001) np->stats.tx_deferred++;
#endif
#if LINUX_VERSION_CODE > 0x20127
np->stats.tx_bytes += np->tx_skbuff[entry]->len;
#endif
np->stats.collisions += (tx_status >> 3) & 15;
np->stats.tx_packets++;
}
/* Free the original skb. */
np->tx_q_bytes -= np->tx_skbuff[entry]->len;
dev_free_skb(np->tx_skbuff[entry]);
np->tx_skbuff[entry] = 0;
}
if (np->tx_full &&
np->cur_tx - np->dirty_tx < TX_QUEUE_LEN - 4
&& np->tx_q_bytes < TX_BUG_FIFO_LIMIT) {
/* The ring is no longer full, clear tbusy. */
np->tx_full = 0;
clear_bit(0, (void*)&dev->tbusy);
netif_wake_queue(dev);
}
/* Abnormal error summary/uncommon events handlers. */
if (intr_status & (AbnormalIntr | TxFIFOUnderflow | IntrPCIErr |
TimerInt | IntrTxStopped))
netdev_error(dev, intr_status);
if (--work_limit < 0) {
printk(KERN_WARNING "%s: Too much work at interrupt, "
"status=0x%4.4x.\n", dev->name, intr_status);
/* Set the timer to re-enable the other interrupts after
10*82usec ticks. */
writel(AbnormalIntr | TimerInt, ioaddr + IntrEnable);
writel(10, ioaddr + GPTimer);
break;
}
} while (1);
if (debug > 3)
printk(KERN_DEBUG "%s: exiting interrupt, status=%#4.4x.\n",
dev->name, (int)readl(ioaddr + IntrStatus));
#if defined(__i386__)
clear_bit(0, (void*)&dev->interrupt);
#else
dev->interrupt = 0;
#endif
return;
}
/* This routine is logically part of the interrupt handler, but separated
for clarity and better register allocation. */
static int netdev_rx(struct net_device *dev)
{
struct netdev_private *np = (struct netdev_private *)dev->priv;
int entry = np->cur_rx % RX_RING_SIZE;
int work_limit = np->dirty_rx + RX_RING_SIZE - np->cur_rx;
if (debug > 4) {
printk(KERN_DEBUG " In netdev_rx(), entry %d status %4.4x.\n",
entry, np->rx_ring[entry].status);
}
/* If EOP is set on the next entry, it's a new packet. Send it up. */
while (--work_limit >= 0) {
struct w840_rx_desc *desc = np->rx_head_desc;
s32 status = le32_to_cpu(desc->status);
if (debug > 4)
printk(KERN_DEBUG " netdev_rx() status was %8.8x.\n",
status);
if (status < 0)
break;
if ((status & 0x38008300) != 0x0300) {
if ((status & 0x38000300) != 0x0300) {
/* Ingore earlier buffers. */
if ((status & 0xffff) != 0x7fff) {
printk(KERN_WARNING "%s: Oversized Ethernet frame spanned "
"multiple buffers, entry %#x status %4.4x!\n",
dev->name, np->cur_rx, status);
np->stats.rx_length_errors++;
}
} else if (status & 0x8000) {
/* There was a fatal error. */
if (debug > 2)
printk(KERN_DEBUG "%s: Receive error, Rx status %8.8x.\n",
dev->name, status);
np->stats.rx_errors++; /* end of a packet.*/
if (status & 0x0890) np->stats.rx_length_errors++;
if (status & 0x004C) np->stats.rx_frame_errors++;
if (status & 0x0002) np->stats.rx_crc_errors++;
}
} else {
struct sk_buff *skb;
/* Omit the four octet CRC from the length. */
int pkt_len = ((status >> 16) & 0x7ff) - 4;
#ifndef final_version
if (debug > 4)
printk(KERN_DEBUG " netdev_rx() normal Rx pkt length %d"
" status %x.\n", pkt_len, status);
#endif
/* Check if the packet is long enough to accept without copying
to a minimally-sized skbuff. */
if (pkt_len < rx_copybreak
&& (skb = dev_alloc_skb(pkt_len + 2)) != NULL) {
skb->dev = dev;
skb_reserve(skb, 2); /* 16 byte align the IP header */
/* Call copy + cksum if available. */
#if HAS_IP_COPYSUM
eth_copy_and_sum(skb, np->rx_skbuff[entry]->tail, pkt_len, 0);
skb_put(skb, pkt_len);
#else
memcpy(skb_put(skb, pkt_len), np->rx_skbuff[entry]->tail,
pkt_len);
#endif
} else {
char *temp = skb_put(skb = np->rx_skbuff[entry], pkt_len);
np->rx_skbuff[entry] = NULL;
#ifndef final_version /* Remove after testing. */
if (le32desc_to_virt(desc->buffer1) != temp)
printk(KERN_ERR "%s: Internal fault: The skbuff addresses "
"do not match in netdev_rx: %p vs. %p / %p.\n",
dev->name, le32desc_to_virt(desc->buffer1),
skb->head, temp);
#endif
}
#ifndef final_version /* Remove after testing. */
/* You will want this info for the initial debug. */
if (debug > 5)
printk(KERN_DEBUG " Rx data %2.2x:%2.2x:%2.2x:%2.2x:%2.2x:"
"%2.2x %2.2x:%2.2x:%2.2x:%2.2x:%2.2x:%2.2x %2.2x%2.2x "
"%d.%d.%d.%d.\n",
skb->data[0], skb->data[1], skb->data[2], skb->data[3],
skb->data[4], skb->data[5], skb->data[6], skb->data[7],
skb->data[8], skb->data[9], skb->data[10],
skb->data[11], skb->data[12], skb->data[13],
skb->data[14], skb->data[15], skb->data[16],
skb->data[17]);
#endif
skb->protocol = eth_type_trans(skb, dev);
netif_rx(skb);
dev->last_rx = jiffies;
np->stats.rx_packets++;
#if LINUX_VERSION_CODE > 0x20127
np->stats.rx_bytes += pkt_len;
#endif
}
entry = (++np->cur_rx) % RX_RING_SIZE;
np->rx_head_desc = &np->rx_ring[entry];
}
/* Refill the Rx ring buffers. */
for (; np->cur_rx - np->dirty_rx > 0; np->dirty_rx++) {
struct sk_buff *skb;
entry = np->dirty_rx % RX_RING_SIZE;
if (np->rx_skbuff[entry] == NULL) {
skb = dev_alloc_skb(np->rx_buf_sz);
np->rx_skbuff[entry] = skb;
if (skb == NULL)
break; /* Better luck next round. */
skb->dev = dev; /* Mark as being used by this device. */
np->rx_ring[entry].buffer1 = virt_to_le32desc(skb->tail);
}
np->rx_ring[entry].status = cpu_to_le32(DescOwn);
}
return 0;
}
static void netdev_error(struct net_device *dev, int intr_status)
{
long ioaddr = dev->base_addr;
struct netdev_private *np = (struct netdev_private *)dev->priv;
if (debug > 2)
printk(KERN_DEBUG "%s: Abnormal event, %8.8x.\n",
dev->name, intr_status);
if (intr_status == 0xffffffff)
return;
if (intr_status & TxFIFOUnderflow) {
np->csr6 += 0x4000; /* Bump up the Tx threshold */
printk(KERN_DEBUG "%s: Tx underflow, increasing threshold to %8.8x.\n",
dev->name, np->csr6);
writel(np->csr6, ioaddr + NetworkConfig);
}
if (intr_status & IntrRxDied) { /* Missed a Rx frame. */
np->stats.rx_errors++;
}
if (intr_status & TimerInt) {
/* Re-enable other interrupts. */
writel(0x1A0F5, ioaddr + IntrEnable);
}
np->stats.rx_missed_errors += readl(ioaddr + RxMissed) & 0xffff;
writel(0, ioaddr + RxStartDemand);
}
static struct net_device_stats *get_stats(struct net_device *dev)
{
long ioaddr = dev->base_addr;
struct netdev_private *np = (struct netdev_private *)dev->priv;
/* The chip only need report frame silently dropped. */
if (dev->start)
np->stats.rx_missed_errors += readl(ioaddr + RxMissed) & 0xffff;
return &np->stats;
}
static unsigned const ethernet_polynomial = 0x04c11db7U;
static inline u32 ether_crc(int length, unsigned char *data)
{
int crc = -1;
while(--length >= 0) {
unsigned char current_octet = *data++;
int bit;
for (bit = 0; bit < 8; bit++, current_octet >>= 1) {
crc = (crc << 1) ^
((crc < 0) ^ (current_octet & 1) ? ethernet_polynomial : 0);
}
}
return crc;
}
static void set_rx_mode(struct net_device *dev)
{
struct netdev_private *np = (struct netdev_private *)dev->priv;
long ioaddr = dev->base_addr;
u32 mc_filter[2]; /* Multicast hash filter */
u32 rx_mode;
if (dev->flags & IFF_PROMISC) { /* Set promiscuous. */
/* Unconditionally log net taps. */
printk(KERN_NOTICE "%s: Promiscuous mode enabled.\n", dev->name);
memset(mc_filter, 0xff, sizeof(mc_filter));
rx_mode = AcceptBroadcast | AcceptMulticast | AcceptAllPhys
| AcceptMyPhys;
} else if ((dev->mc_count > multicast_filter_limit)
|| (dev->flags & IFF_ALLMULTI)) {
/* Too many to match, or accept all multicasts. */
memset(mc_filter, 0xff, sizeof(mc_filter));
rx_mode = AcceptBroadcast | AcceptMulticast | AcceptMyPhys;
} else {
struct dev_mc_list *mclist;
int i;
memset(mc_filter, 0, sizeof(mc_filter));
for (i = 0, mclist = dev->mc_list; mclist && i < dev->mc_count;
i++, mclist = mclist->next) {
set_bit((ether_crc(ETH_ALEN, mclist->dmi_addr) >> 26) ^ 0x3F,
mc_filter);
}
rx_mode = AcceptBroadcast | AcceptMulticast | AcceptMyPhys;
}
writel(mc_filter[0], ioaddr + MulticastFilter0);
writel(mc_filter[1], ioaddr + MulticastFilter1);
np->csr6 &= ~0x00F8;
np->csr6 |= rx_mode;
writel(np->csr6, ioaddr + NetworkConfig);
}
static int mii_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
{
u16 *data = (u16 *)&rq->ifr_data;
switch(cmd) {
case SIOCDEVPRIVATE: /* Get the address of the PHY in use. */
data[0] = ((struct netdev_private *)dev->priv)->phys[0] & 0x1f;
/* Fall Through */
case SIOCDEVPRIVATE+1: /* Read the specified MII register. */
data[3] = mdio_read(dev, data[0] & 0x1f, data[1] & 0x1f);
return 0;
case SIOCDEVPRIVATE+2: /* Write the specified MII register */
if (!capable(CAP_NET_ADMIN))
return -EPERM;
mdio_write(dev, data[0] & 0x1f, data[1] & 0x1f, data[2]);
return 0;
default:
return -EOPNOTSUPP;
}
}
static int netdev_close(struct net_device *dev)
{
long ioaddr = dev->base_addr;
struct netdev_private *np = (struct netdev_private *)dev->priv;
int i;
dev->start = 0;
dev->tbusy = 1;
if (debug > 1) {
printk(KERN_DEBUG "%s: Shutting down ethercard, status was %8.8x "
"Config %8.8x.\n", dev->name, (int)readl(ioaddr + IntrStatus),
(int)readl(ioaddr + NetworkConfig));
printk(KERN_DEBUG "%s: Queue pointers were Tx %d / %d, Rx %d / %d.\n",
dev->name, np->cur_tx, np->dirty_tx, np->cur_rx, np->dirty_rx);
}
/* Disable interrupts by clearing the interrupt mask. */
writel(0x0000, ioaddr + IntrEnable);
/* Stop the chip's Tx and Rx processes. */
writel(np->csr6 &= ~0x20FA, ioaddr + NetworkConfig);
del_timer(&np->timer);
if (readl(ioaddr + NetworkConfig) != 0xffffffff)
np->stats.rx_missed_errors += readl(ioaddr + RxMissed) & 0xffff;
#ifdef __i386__
if (debug > 2) {
printk("\n"KERN_DEBUG" Tx ring at %8.8x:\n",
(int)virt_to_le32desc(np->tx_ring));
for (i = 0; i < TX_RING_SIZE; i++)
printk(" #%d desc. %4.4x %4.4x %8.8x.\n",
i, np->tx_ring[i].length,
np->tx_ring[i].status, np->tx_ring[i].buffer1);
printk("\n"KERN_DEBUG " Rx ring %8.8x:\n",
(int)virt_to_le32desc(np->rx_ring));
for (i = 0; i < RX_RING_SIZE; i++) {
printk(KERN_DEBUG " #%d desc. %4.4x %4.4x %8.8x\n",
i, np->rx_ring[i].length,
np->rx_ring[i].status, np->rx_ring[i].buffer1);
}
}
#endif /* __i386__ debugging only */
free_irq(dev->irq, dev);
/* Free all the skbuffs in the Rx queue. */
for (i = 0; i < RX_RING_SIZE; i++) {
np->rx_ring[i].status = 0;
if (np->rx_skbuff[i]) {
#if LINUX_VERSION_CODE < 0x20100
np->rx_skbuff[i]->free = 1;
#endif
dev_free_skb(np->rx_skbuff[i]);
}
np->rx_skbuff[i] = 0;
}
for (i = 0; i < TX_RING_SIZE; i++) {
if (np->tx_skbuff[i])
dev_free_skb(np->tx_skbuff[i]);
np->tx_skbuff[i] = 0;
}
MOD_DEC_USE_COUNT;
return 0;
}
#ifdef MODULE
int init_module(void)
{
if (debug) /* Emit version even if no cards detected. */
printk(KERN_INFO "%s" KERN_INFO "%s", version1, version2);
return pci_drv_register(&winbond840_drv_id, NULL);
}
void cleanup_module(void)
{
struct net_device *next_dev;
pci_drv_unregister(&winbond840_drv_id);
/* No need to check MOD_IN_USE, as sys_delete_module() checks. */
while (root_net_dev) {
struct netdev_private *np = (void *)(root_net_dev->priv);
unregister_netdev(root_net_dev);
#ifdef USE_IO_OPS
release_region(root_net_dev->base_addr, pci_tbl[np->chip_id].io_size);
#else
iounmap((char *)(root_net_dev->base_addr));
#endif
next_dev = np->next_module;
if (np->priv_addr)
kfree(np->priv_addr);
kfree(root_net_dev);
root_net_dev = next_dev;
}
}
#else
int winbond840_probe(struct net_device *dev)
{
if (pci_drv_register(&winbond840_drv_id, dev) < 0)
return -ENODEV;
printk(KERN_INFO "%s" KERN_INFO "%s", version1, version2);
return 0;
}
#endif /* MODULE */
/*
* Local variables:
* compile-command: "gcc -DMODULE -Wall -Wstrict-prototypes -O6 -c winbond-840.c"
* simple-compile-command: "gcc -DMODULE -O6 -c winbond-840.c"
* c-indent-level: 4
* c-basic-offset: 4
* tab-width: 4
* End:
*/
hi Dick,
On Tue, 28 Nov 2000, John B. Jacobsen wrote:
> /* Set the copy breakpoint for the copy-only-tiny-frames scheme.
> Setting to > 1518 effectively disables this feature. */
> static int rx_copybreak = 0;
A skeleton driver has a higher responsibility than just "a driver" and
thus needs to be ideal. The above line makes it less so than it would have
been without it.
Regards,
Tigran
JBJ> #ifdef INLINE_PCISCAN
JBJ> #include "k_compat.h"
JBJ> #else
JBJ> #include "pci-scan.h"
JBJ> #include "kern_compat.h"
JBJ> #endif
I quess you need to convert it to kernel PCI API first and probably also to
optimize away the LINUX_VERSION_CODE checks (we know it's 2.4).
--
Meelis Roos ([email protected])
Meelis Roos writes:
> JBJ> #ifdef INLINE_PCISCAN
> JBJ> #include "k_compat.h"
> JBJ> #else
> JBJ> #include "pci-scan.h"
> JBJ> #include "kern_compat.h"
> JBJ> #endif
>
> I quess you need to convert it to kernel PCI API first and probably also to
> optimize away the LINUX_VERSION_CODE checks (we know it's 2.4).
Actually, there is some benefit in leaving the LINUX_VERSION_CODE checks
there... If someone wants to back-port the driver to 2.2, this makes it
much easier. Also, some people like to maintain a single driver for all
of the kernel versions, so they don't have to bugfix each driver version.
Cheers, Andreas
--
Andreas Dilger \ "If a man ate a pound of pasta and a pound of antipasto,
\ would they cancel out, leaving him still hungry?"
http://www-mddsp.enel.ucalgary.ca/People/adilger/ -- Dogbert
> Actually, there is some benefit in leaving the LINUX_VERSION_CODE checks
> there... If someone wants to back-port the driver to 2.2, this makes it
> much easier. Also, some people like to maintain a single driver for all
> of the kernel versions, so they don't have to bugfix each driver version.
backports hurt forward progress.
** Reply to message from Mark Hahn <[email protected]> on Thu,
30 Nov 2000 14:16:16 -0500 (EST)
> > Actually, there is some benefit in leaving the LINUX_VERSION_CODE checks
> > there... If someone wants to back-port the driver to 2.2, this makes it
> > much easier. Also, some people like to maintain a single driver for all
> > of the kernel versions, so they don't have to bugfix each driver version.
>
> backports hurt forward progress.
Not necessarily - it all depends on what your driver does. In many cases,
supporting 2.2 and 2.4 is easy, and all you need are a few #if's. It's
certainly much better to have a dozen or so #if's sprinkled throughout the code
than to have two separate source trees, and have to make the same change to
multiple files.
Kernel drivers that are not easy to maintain simply delay the release of each
kernel version. Besides, code is back-ported from 2.4 to 2.2 all the time.
--
Timur Tabi - [email protected]
Interactive Silicon - http://www.interactivesi.com
When replying to a mailing-list message, please direct the reply to the mailing list only. Don't send another copy to me.
> > Actually, there is some benefit in leaving the LINUX_VERSION_CODE checks
> > there... If someone wants to back-port the driver to 2.2, this makes it
> > much easier. Also, some people like to maintain a single driver for all
> > of the kernel versions, so they don't have to bugfix each driver version.
>
> backports hurt forward progress.
beware of content free dogma
Or in longer terms: Backporting is actually often very useful. It has helped
in many cases to say definitively 'this must be the driver' or 'its stable on
2.2 are we sure the pci code is right' type things. Think of debugging as
solving a large set of simultaneous equations. The more equations you have
the easier it is
[email protected] said:
> Not necessarily - it all depends on what your driver does. In many
> cases, supporting 2.2 and 2.4 is easy, and all you need are a few
> #if's. It's certainly much better to have a dozen or so #if's
> sprinkled throughout the code than to have two separate source trees,
> and have to make the same change to multiple files.
It's even better to do it without the ugly preprocessor magic - see
include/linux/compatmac.h
There are a few things missing from there - include/linux/mtd/compatmac.h
has more. One day we'll get round to removing the latter and merging it
into the main one, hopefully.
--
dwmw2
On Tue, 28 Nov 2000, John B. Jacobsen wrote:
>
> /* winbond-840.c: A Linux PCI network adapter skeleton device driver. */
It is already in 2.4.x
Jeff
On Fri, Dec 01, 2000 at 09:26:29AM +0000, David Woodhouse wrote:
>
> [email protected] said:
> > Not necessarily - it all depends on what your driver does. In many
> > cases, supporting 2.2 and 2.4 is easy, and all you need are a few
> > #if's. It's certainly much better to have a dozen or so #if's
> > sprinkled throughout the code than to have two separate source trees,
> > and have to make the same change to multiple files.
>
> It's even better to do it without the ugly preprocessor magic - see
> include/linux/compatmac.h
>
> There are a few things missing from there - include/linux/mtd/compatmac.h
> has more. One day we'll get round to removing the latter and merging it
> into the main one, hopefully.
A while ago, I started working on the Mother Of All compatmac.h files,
trying to merge Don Becker's stuff, yours, David Hinds, and stuff
from my own Comedi package. It quickly got out of control, as
including compatmac.h (or kern_compat.h, as I called it) would
include most of the include/linux directory. I've since settled for
setting up a separate include/linux tree with header files
named pci.h, mm.h, etc., that #define the right things and then
do an #include_next. Interested parties can find it in Comedi
(http://stm.lbl.gov/comedi).
dave...