On Wed, 11 Jan 2006 [email protected] wrote:
> The patch titled
> Areca RAID driver (arcmsr) update2
> has been added to the -mm tree. Its filename is
> areca-raid-driver-arcmsr-update2.patch
>
> From: "erich" <[email protected]>
>
> The arcmsr patch file update2 works for:
>
> 1. use printk levels
> 2. change pPCI_DEV bad naming into pci_device
> 3. delete some unreadable comments
> 4. try to fit source files into 80 columns (lots fixed, lots to go)
> 5. Tab size in Linux kernel is 8 (not less).
> 6. Put changelog comments in Documentation/scsi/ChangeLog.arcmsr
>
> Signed-off-by: Andrew Morton <[email protected]>
> ---
>
> drivers/scsi/arcmsr/arcmsr.c | 2827 +++++++-------
> drivers/scsi/arcmsr/arcmsr.h | 5043 ++++----------------------
> 4 files changed, 2289 insertions(+), 5775 deletions(-)
>
> diff -puN drivers/scsi/arcmsr/arcmsr.c~areca-raid-driver-arcmsr-update2 drivers/scsi/arcmsr/arcmsr.c
> --- devel/drivers/scsi/arcmsr/arcmsr.c~areca-raid-driver-arcmsr-update2 2006-01-11 19:05:35.000000000 -0800
> +++ devel-akpm/drivers/scsi/arcmsr/arcmsr.c 2006-01-11 19:05:35.000000000 -0800
> @@ -99,7 +52,6 @@
> #include <linux/errno.h>
> #include <linux/types.h>
> #include <linux/delay.h>
> -#include <linux/dma-mapping.h>
Why delete this include? Some constants from it are used in arcmsr.c.
> #include <linux/timer.h>
> #include <linux/pci.h>
> #include <asm/dma.h>
> +*******************************************************************************
> */
> -static uint8_t arcmsr_adapterCnt = 0;
> +static uint8_t arcmsr_adapterCnt=0;
The first way (with spaces around the '=') is preferred AFAIK.
(in MANY places)
However, static data does not need to be init to 0.
> +static int arcmsr_initialize(struct ACB *pACB,struct pci_dev *pci_device);
> +static int arcmsr_iop_ioctlcmd(struct ACB *pACB,int ioctl_cmd,void *arg);
Please use spaces after ','.
> static int arcmsr_release(struct Scsi_Host *);
> -static int arcmsr_queue_command(struct scsi_cmnd *cmd,
> - void (*done) (struct scsi_cmnd *));
> static int arcmsr_cmd_abort(struct scsi_cmnd *);
> static int arcmsr_bus_reset(struct scsi_cmnd *);
> -static int arcmsr_ioctl(struct scsi_device *dev, int ioctl_cmd, void __user *arg);
> -static int __devinit arcmsr_device_probe(struct pci_dev *pPCI_DEV,
> - const struct pci_device_id *id);
> -static void arcmsr_device_remove(struct pci_dev *pPCI_DEV);
> +static int arcmsr_ioctl(struct scsi_device * dev, int ioctl_cmd, void *arg);
Argh, what happened to the __user addition that makes sparse happy?
Did you run sparse on it yet?
> @@ -155,131 +108,167 @@ static irqreturn_t arcmsr_interrupt(stru
> static uint8_t arcmsr_wait_msgint_ready(struct ACB *pACB);
> +*/
> +*/
> +static struct class_device_attribute arcmsr_firmware_info_attr=
> +{
> + .attr={
> + .name="firmware_info",
> + .mode=S_IRUGO,
> + },
> + .show=arcmsr_show_firmware_info,
Would be much more readable with spaces around the '=' sign.
(in MANY places)
> +*/
> */
> +*/
> }
> - /* allocate scsi host information (includes our adapter)
> - * scsi_host_alloc==scsi_register */
> - if ((host = scsi_host_alloc(&arcmsr_scsi_host_template,
> - sizeof(struct ACB))) == NULL) {
> - printk("arcmsr%d: adapter probe: scsi_host_alloc error \n",
> - arcmsr_adapterCnt);
> + if ((host=scsi_host_alloc(&arcmsr_scsi_host_template,
> + sizeof(struct ACB)))==0) {
s/0/NULL/ for sparse
> static int arcmsr_fops_open(struct inode *inode, struct file *filep)
> {
> - int i, minor;
> - struct HCBARC *pHCBARC = &arcmsr_host_control_block;
> + int i,minor;
> + struct HCBARC *pHCBARC= &arcmsr_host_control_block;
> struct ACB *pACB;
>
> - minor = MINOR(inode->i_rdev);
> - if (minor >= pHCBARC->adapterCnt)
> - return -ENXIO;
> - for (i = 0; i < ARCMSR_MAX_ADAPTER; i++) {
> - if ((pACB = pHCBARC->pACB[i]))
> - if (pACB->adapter_index == minor)
> + minor=MINOR(inode->i_rdev);
> + if (minor >=pHCBARC->adapterCnt)
> + return ENXIO;
> + for(i=0;i<ARCMSR_MAX_ADAPTER;i++) {
Add some spaces, please.
> + pACB=pHCBARC->pACB[i];
> + if (pACB) {
> + if (pACB->adapter_index==minor)
> break;
> + }
> }
> - if (i >= ARCMSR_MAX_ADAPTER)
> - return -ENXIO;
> - return 0; /* success */
> + if (i>=ARCMSR_MAX_ADAPTER)
> + return ENXIO;
> + return 0;/* success */
> }
> -
> static int arcmsr_fops_close(struct inode *inode, struct file *filep)
> {
> - int i, minor;
> - struct HCBARC *pHCBARC = &arcmsr_host_control_block;
> + int i,minor;
> + struct HCBARC *pHCBARC= &arcmsr_host_control_block;
> struct ACB *pACB;
>
> - minor = MINOR(inode->i_rdev);
> - if (minor >= pHCBARC->adapterCnt)
> - return -ENXIO;
> - for (i = 0; i < ARCMSR_MAX_ADAPTER; i++) {
> - if ((pACB = pHCBARC->pACB[i]))
> - if (pACB->adapter_index == minor)
> + minor=MINOR(inode->i_rdev);
> + if (minor >=pHCBARC->adapterCnt)
> + return ENXIO;
> + for(i=0;i<ARCMSR_MAX_ADAPTER;i++) {
Needs spaces.
> + pACB=pHCBARC->pACB[i];
> + if (pACB) {
> + if (pACB->adapter_index==minor)
> break;
> + }
> }
> - if (i >= ARCMSR_MAX_ADAPTER)
> - return -ENXIO;
> + if (i>=ARCMSR_MAX_ADAPTER)
> + return ENXIO;
> return 0;
> }
> -
> static int arcmsr_fops_ioctl(struct inode *inode, struct file *filep,
> - unsigned int ioctl_cmd, unsigned long arg)
> + unsigned int ioctl_cmd, unsigned long arg)
> {
> - int i, minor;
> - struct HCBARC *pHCBARC = &arcmsr_host_control_block;
> + int i,minor;
> + struct HCBARC *pHCBARC= &arcmsr_host_control_block;
> struct ACB *pACB;
>
> - minor = MINOR(inode->i_rdev);
> - if (minor >= pHCBARC->adapterCnt)
> - return -ENXIO;
> - for (i = 0; i < ARCMSR_MAX_ADAPTER; i++) {
> - if ((pACB = pHCBARC->pACB[i]))
> - if (pACB->adapter_index == minor)
> + minor=MINOR(inode->i_rdev);
> + if (minor >=pHCBARC->adapterCnt)
> + return ENXIO;
> + for(i=0;i<ARCMSR_MAX_ADAPTER;i++) {
Spaces.
> + pACB=pHCBARC->pACB[i];
> + if (pACB) {
> + if (pACB->adapter_index==minor)
> break;
> + }
> }
> - if (i >= ARCMSR_MAX_ADAPTER)
> - return -ENXIO;
> - /*
> - ************************************************************
> - ** We do not allow multi ioctls to the driver at the same time.
> - ************************************************************
> - */
> - return arcmsr_iop_ioctlcmd(pACB, ioctl_cmd, (void __user *)arg);
> + if (i>=ARCMSR_MAX_ADAPTER)
> + return ENXIO;
> + return arcmsr_iop_ioctlcmd(pACB,ioctl_cmd,(void *)arg);
> }
> -
> static void arcmsr_report_sense_info(struct CCB *pCCB)
> {
> - struct scsi_cmnd *pcmd = pCCB->pcmd;
> - struct SENSE_DATA *psenseBuffer =
> - (struct SENSE_DATA *)pcmd->sense_buffer;
> + struct scsi_cmnd *pcmd=pCCB->pcmd;
> + struct SENSE_DATA *psenseBuffer=(struct SENSE_DATA *)pcmd->sense_buffer;
>
> - pcmd->result = DID_OK << 16;
> + pcmd->result=DID_OK << 16;
> if (psenseBuffer) {
> - int sense_data_length =
> - sizeof(struct SENSE_DATA) <
> - sizeof(pcmd->
> - sense_buffer) ? sizeof(struct SENSE_DATA) :
> - sizeof(pcmd->sense_buffer);
> + int sense_data_length=
> + sizeof(struct SENSE_DATA) < sizeof(pcmd->sense_buffer)
> + ? sizeof(struct SENSE_DATA) : sizeof(pcmd->sense_buffer);
> memset(psenseBuffer, 0, sizeof(pcmd->sense_buffer));
> - memcpy(psenseBuffer, pCCB->arcmsr_cdb.SenseData,
> - sense_data_length);
> - psenseBuffer->ErrorCode = 0x70;
> - psenseBuffer->Valid = 1;
> + memcpy(psenseBuffer,pCCB->arcmsr_cdb.SenseData,sense_data_length);
> + psenseBuffer->ErrorCode=0x70;
Better to use some named constant or define instead of magic numbers
like 0x70.
> + psenseBuffer->Valid=1;
> }
> }
> @@ -1141,240 +1120,214 @@ static void arcmsr_iop_parking(struct AC
> +*/
> +static int arcmsr_ioctl(struct scsi_device *dev,int ioctl_cmd,void *arg)
> {
> struct ACB *pACB;
> - struct HCBARC *pHCBARC = &arcmsr_host_control_block;
> - int32_t match = 0x55AA, i;
> + struct HCBARC *pHCBARC= &arcmsr_host_control_block;
> + int32_t match=0x55AA,i;
>
> - for (i = 0; i < ARCMSR_MAX_ADAPTER; i++) {
> - if ((pACB = pHCBARC->pACB[i])) {
> - if (pACB->host == dev->host) {
> - match = i;
> + for(i=0;i<ARCMSR_MAX_ADAPTER;i++) {
Spaces.
> + pACB=pHCBARC->pACB[i];
> + if (pACB) {
> + if (pACB->host==dev->host) {
> + match=i;
> break;
> }
> }
> }
> - if (match == 0x55AA)
> - return -ENXIO;
> + if (match==0x55AA)
> + return ENXIO;
> if (!arg)
> return -EINVAL;
> -
> - return arcmsr_iop_ioctlcmd(pACB, ioctl_cmd, arg);
> + return(arcmsr_iop_ioctlcmd(pACB,ioctl_cmd,arg));
Ugh. I guess that there was some reason that this patch
reverts a lot of previous changes...?
and also makes some good changes.
> @@ -1431,145 +1386,150 @@ static struct CCB *arcmsr_get_freeccb(st
> +*/
> static int arcmsr_seek_cmd2abort(struct scsi_cmnd *abortcmd)
> {
> - struct ACB *pACB = (struct ACB *)abortcmd->device->host->hostdata;
> + struct ACB *pACB=(struct ACB *) abortcmd->device->host->hostdata;
> struct CCB *pCCB;
> - uint32_t intmask_org, mask;
> - int i = 0, pendingcount;
> + uint32_t intmask_org,mask;
> + int i=0,pendingcount;
>
> pACB->num_aborts++;
> /*
> - ******************************************************************
> - ** It is the upper layer do abort command this lock just prior to
> - ** calling us.
> - ** First determine if we currently own this command.
> - ** Start by searching the device queue. If not found
> - ** at all, and the system wanted us to just abort the
> - ** command return success.
> - ******************************************************************
> - */
> - if (atomic_read(&pACB->ccboutstandingcount) != 0) {
> - for (i = 0; i < ARCMSR_MAX_FREECCB_NUM; i++) {
> - pCCB = pACB->pccb_pool[i];
> - if (pCCB->startdone == ARCMSR_CCB_START) {
> - if (pCCB->pcmd == abortcmd) {
> - pCCB->startdone = ARCMSR_CCB_ABORTED;
> - printk
> - ("arcmsr%d: scsi id=%d lun=%d abort ccb '0x%p' outstanding command \n",
> - pACB->adapter_index,
> - abortcmd->device->id,
> - abortcmd->device->lun, pCCB);
> + *****************************************************************
> + ** It is the upper layer do abort command this lock just prior
> + ** to calling us.
> + ** First determine if we currently own this command.
> + ** Start by searching the device queue. If not found
> + ** at all,and the system wanted us to just abort the
> + ** command return success.
> + *****************************************************************
> + */
> + if (atomic_read(&pACB->ccboutstandingcount)!=0) {
> + for(i=0;i<ARCMSR_MAX_FREECCB_NUM;i++) {
Spaces.
> + pCCB=pACB->pccb_pool[i];
> + if (pCCB->startdone==ARCMSR_CCB_START) {
> + if (pCCB->pcmd==abortcmd) {
> + pCCB->startdone=ARCMSR_CCB_ABORTED;
> + printk(KERN_NOTICE
> + "arcmsr%d: scsi id=%d lun=%d"
> + " abort ccb '0x%p' outstanding command\n"
> + ,pACB->adapter_index
> + ,abortcmd->device->id
> + ,abortcmd->device->lun
> + ,pCCB);
> goto abort_outstanding_cmd;
> }
> }
> }
> }
> /*
> - **********************************************************
> - ** seek this command at our command list
> - ** if command found then remove, abort it and free this CCB
> - **********************************************************
> - */
> - pendingcount = atomic_read(&pACB->ccbpendingcount);
> - if (pendingcount > 0) {
> + **********************************************************
> + ** seek this command at our command list
> + ** if command found then remove,abort it and free this CCB
> + **********************************************************
> + */
> + pendingcount=atomic_read(&pACB->ccbpendingcount);
> + if (pendingcount>0) {
> do {
> - pCCB = arcmsr_get_pendingccb(pACB);
> - if (!pCCB)
> + pCCB=arcmsr_get_pendingccb(pACB);
> + if (pCCB==NULL)
> break;
> - if (pCCB->pcmd == abortcmd) {
> - printk
> - ("arcmsr%d: scsi id=%d lun=%d abort ccb '0x%p' pending command \n",
> - pACB->adapter_index, abortcmd->device->id,
> - abortcmd->device->lun, pCCB);
> - pCCB->startdone = ARCMSR_CCB_ABORTED;
> - pCCB->pcmd->result = DID_ABORT << 16;
> - arcmsr_ccb_complete(pCCB, 0);
> + if (pCCB->pcmd==abortcmd) {
> + printk(KERN_NOTICE
> + "arcmsr%d: scsi id=%d lun=%d"
> + " abort ccb '0x%p' pending command \n"
> + ,pACB->adapter_index
> + ,abortcmd->device->id
> + ,abortcmd->device->lun
> + ,pCCB);
> + pCCB->startdone=ARCMSR_CCB_ABORTED;
> + pCCB->pcmd->result=DID_ABORT << 16;
> + arcmsr_ccb_complete(pCCB,0);
> return SUCCESS;
> } else
> - arcmsr_queue_pendingccb(pACB, pCCB);
> + arcmsr_queue_pendingccb(pACB,pCCB);
> } while (pendingcount--);
> }
> return SUCCESS;
> -
> abort_outstanding_cmd:
> - msleep_interruptible(3000); /* wait for 3 sec for all command done */
> + /*wait for 3 sec for all command done*/
> + msleep_interruptible(3000);
> /* disable all outbound interrupt */
> - intmask_org = readl(&pACB->pmu->outbound_intmask);
> - writel(intmask_org | ARCMSR_MU_OUTBOUND_ALL_INTMASKENABLE,
> - &pACB->pmu->outbound_intmask);
> - arcmsr_polling_ccbdone(pACB, pCCB);
> + intmask_org=readl(&pACB->pmu->outbound_intmask);
> + writel(intmask_org|ARCMSR_MU_OUTBOUND_ALL_INTMASKENABLE
> + ,&pACB->pmu->outbound_intmask);
> + arcmsr_polling_ccbdone(pACB,pCCB);
> /* enable all outbound interrupt */
> - mask = ~(ARCMSR_MU_OUTBOUND_POSTQUEUE_INTMASKENABLE |
> - ARCMSR_MU_OUTBOUND_DOORBELL_INTMASKENABLE);
> - writel(intmask_org & mask, &pACB->pmu->outbound_intmask);
> + mask=~(ARCMSR_MU_OUTBOUND_POSTQUEUE_INTMASKENABLE
> + |ARCMSR_MU_OUTBOUND_DOORBELL_INTMASKENABLE);
> + writel(intmask_org & mask,&pACB->pmu->outbound_intmask);
> return SUCCESS;
> }
> +*/
> +*/
> static int arcmsr_release(struct Scsi_Host *host)
> {
> struct ACB *pACB;
> - struct HCBARC *pHCBARC = &arcmsr_host_control_block;
> - uint8_t match = 0xff, i;
> + struct HCBARC *pHCBARC= &arcmsr_host_control_block;
> + uint8_t match=0xff,i;
>
> - if (!host)
> - return -ENXIO;
> - pACB = (struct ACB *)host->hostdata;
> + if (host==NULL)
> + return ENXIO;
Like this reversion. Why?
> + pACB=(struct ACB *)host->hostdata;
> if (!pACB)
> - return -ENXIO;
> -
> - for (i = 0; i < ARCMSR_MAX_ADAPTER; i++) {
> - if (pHCBARC->pACB[i] == pACB)
> - match = i;
> + return ENXIO;
> + for(i=0;i<ARCMSR_MAX_ADAPTER;i++) {
> + if (pHCBARC->pACB[i]==pACB)
> + match=i;
> }
> - if (match == 0xff)
> - return -ENXIO;
> -
> + if (match==0xff)
> + return ENXIO;
> arcmsr_pcidev_disattach(pACB);
> - for (i = 0; i < ARCMSR_MAX_ADAPTER; i++) {
> + for(i=0;i<ARCMSR_MAX_ADAPTER;i++) {
Spaces.
> if (pHCBARC->pACB[i])
> return 0;
> }
> diff -puN drivers/scsi/arcmsr/arcmsr.h~areca-raid-driver-arcmsr-update2 drivers/scsi/arcmsr/arcmsr.h
> --- devel/drivers/scsi/arcmsr/arcmsr.h~areca-raid-driver-arcmsr-update2 2006-01-11 19:05:35.000000000 -0800
> +++ devel-akpm/drivers/scsi/arcmsr/arcmsr.h 2006-01-11 19:05:35.000000000 -0800
> @@ -1,11 +1,11 @@
> /*
> ** modification, are permitted provided that the following conditions
> ** are met:
> @@ -34,105 +34,127 @@
> ** IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
> ** OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
> ** IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
> -** INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES(INCLUDING, BUT
> -** NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
> +** INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES(INCLUDING,BUT
> +** NOT LIMITED TO,PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
I still prefer a Space after comma.
> ** DATA, OR PROFITS; OR BUSINESS INTERRUPTION)HOWEVER CAUSED AND ON ANY
> ** THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
> **(INCLUDING NEGLIGENCE OR OTHERWISE)ARISING IN ANY WAY OUT OF THE USE OF
> ** THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
> */
> -
> -#define dma_addr_hi32(addr) (uint32_t) ((addr>>16)>>16)
> -#define dma_addr_lo32(addr) (uint32_t) (addr & 0xffffffff)
> -
> +#include <linux/config.h>
The make (build) procedure now includes linux/config.h for every
build, so this #include isn't needed.
> +#define dma_addr_lo32(addr) (uint32_t) (addr & 0xffffffff)
> +
> +#ifndef DMA_64BIT_MASK
> + #define DMA_64BIT_MASK 0xffffffffffffffffULL
> + #define DMA_32BIT_MASK 0x00000000ffffffffULL
> +#endif
Is the above for some back-version kernel compatibility?
Otherwise all that is needed is to #include <linux/dma-mapping.h>.
I also saw 2 cases of "unknow" which should be "unknown".
--
~Randy
"Randy.Dunlap" <[email protected]> wrote:
>
> Ugh. I guess that there was some reason that this patch
> reverts a lot of previous changes...?
erp, sorry. Erich's patch generated a single 5000-line reject so I kind of
jammed it in and lost some of your changes. I meant to go back and redo
them on top but haven't got there yet.