Add the "disable-hpd" binding, used to disable hotplug detected
functionality in the driver. When it's enabled the driver assumes that
the connector is always connected and disables the hotplug detect
related IRQ.
Signed-off-by: Mykyta Poturai <[email protected]>
---
.../devicetree/bindings/display/bridge/renesas,dw-hdmi.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
index 3f6072651182..b2b899f46b86 100644
--- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
+++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
@@ -39,6 +39,7 @@ Optional properties:
- power-domains: Shall reference the power domain that contains the DWC HDMI,
if any.
+- disable-hpd: Disables the hotplug detect feature
Example:
--
2.30.0
Hi,
On 31/01/2021 10:57, Mykyta Poturai wrote:
> Add the "disable-hpd" binding, used to disable hotplug detected
> functionality in the driver. When it's enabled the driver assumes that
> the connector is always connected and disables the hotplug detect
> related IRQ.
DT describes the hardware, not the software behaviour.
So if the HPD is broken, then add a "snps,broken-hpd" instead, or if you want to force output, use the DRM mode forcing, which is handled by the dw-hdmi code:
https://wiki.archlinux.org/index.php/kernel_mode_setting#Forcing_modes
Neil
>
> Signed-off-by: Mykyta Poturai <[email protected]>
> ---
> .../devicetree/bindings/display/bridge/renesas,dw-hdmi.txt | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
> index 3f6072651182..b2b899f46b86 100644
> --- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
> +++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
> @@ -39,6 +39,7 @@ Optional properties:
>
> - power-domains: Shall reference the power domain that contains the DWC HDMI,
> if any.
> +- disable-hpd: Disables the hotplug detect feature
>
>
> Example:
>
Hi Mykyta,
Thank you for the patch.
On Sun, Jan 31, 2021 at 11:57:01AM +0200, Mykyta Poturai wrote:
> Add the "disable-hpd" binding, used to disable hotplug detected
> functionality in the driver. When it's enabled the driver assumes that
> the connector is always connected and disables the hotplug detect
> related IRQ.
>
> Signed-off-by: Mykyta Poturai <[email protected]>
> ---
> .../devicetree/bindings/display/bridge/renesas,dw-hdmi.txt | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
> index 3f6072651182..b2b899f46b86 100644
> --- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
> +++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
> @@ -39,6 +39,7 @@ Optional properties:
>
> - power-domains: Shall reference the power domain that contains the DWC HDMI,
> if any.
> +- disable-hpd: Disables the hotplug detect feature
A similar property has been added to the ti,sn65dsi86 bindings in commit
1dbc979172af ("dt-bindings: drm/bridge: ti-sn65dsi86: Document no-hpd").
A property with the same name exists in panel-common.yaml. Could we
standardize on that name ?
The description should also explain the hardware architecture, not the
driver behaviour. This is what the ti,sn65dsi86 binding documents:
no-hpd:
type: boolean
description:
Set if the HPD line on the bridge isn't hooked up to anything or is
otherwise unusable.
You could use the same description, assuming this is the use case you
want to support. Could you perhaps describe your problem in a bit more
details ? Do you have a system with an HDMI panel that is always
connected, with the HPD signal of the dw-hdmi not connected ?
> Example:
--
Regards,
Laurent Pinchart