Convert the device tree bindings for the STMicroelectronics STi
Peripheral Powerdown reset controller to YAML schema to allow
participating in DT validation.
Signed-off-by: Philipp Zabel <[email protected]>
Cc: Srinivas Kandagatla <[email protected]>
---
.../bindings/reset/st,sti-powerdown.txt | 45 -----------------
.../bindings/reset/st,stih407-powerdown.yaml | 49 +++++++++++++++++++
2 files changed, 49 insertions(+), 45 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
create mode 100644 Documentation/devicetree/bindings/reset/st,stih407-powerdown.yaml
diff --git a/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
deleted file mode 100644
index 92527138bc93..000000000000
--- a/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
+++ /dev/null
@@ -1,45 +0,0 @@
-STMicroelectronics STi family Sysconfig Peripheral Powerdown Reset Controller
-=============================================================================
-
-This binding describes a reset controller device that is used to enable and
-disable on-chip peripheral controllers such as USB and SATA, using
-"powerdown" control bits found in the STi family SoC system configuration
-registers. These have been grouped together into a single reset controller
-device for convenience.
-
-The actual action taken when powerdown is asserted is hardware dependent.
-However, when asserted it may not be possible to access the hardware's
-registers and after an assert/deassert sequence the hardware's previous state
-may no longer be valid.
-
-Please refer to reset.txt in this directory for common reset
-controller binding usage.
-
-Required properties:
-- compatible: Should be "st,stih407-powerdown"
-- #reset-cells: 1, see below
-
-example:
-
- powerdown: powerdown-controller {
- compatible = "st,stih407-powerdown";
- #reset-cells = <1>;
- };
-
-
-Specifying powerdown control of devices
-=======================================
-
-Device nodes should specify the reset channel required in their "resets"
-property, containing a phandle to the powerdown device node and an
-index specifying which channel to use, as described in reset.txt
-
-example:
-
- st_dwc3: dwc3@8f94000 {
- resets = <&powerdown STIH407_USB3_POWERDOWN>,
- };
-
-Macro definitions for the supported reset channels can be found in:
-
-include/dt-bindings/reset/stih407-resets.h
diff --git a/Documentation/devicetree/bindings/reset/st,stih407-powerdown.yaml b/Documentation/devicetree/bindings/reset/st,stih407-powerdown.yaml
new file mode 100644
index 000000000000..d3790e602659
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/st,stih407-powerdown.yaml
@@ -0,0 +1,49 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/reset/st,stih407-powerdown.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics STi family Sysconfig Peripheral Powerdown Reset Controller
+
+maintainers:
+ - Srinivas Kandagatla <[email protected]>
+
+description: |
+ This binding describes a reset controller device that is used to enable and
+ disable on-chip peripheral controllers such as USB and SATA, using
+ "powerdown" control bits found in the STi family SoC system configuration
+ registers. These have been grouped together into a single reset controller
+ device for convenience.
+
+ The actual action taken when powerdown is asserted is hardware dependent.
+ However, when asserted it may not be possible to access the hardware's
+ registers and after an assert/deassert sequence the hardware's previous state
+ may no longer be valid.
+
+properties:
+ compatible:
+ const: st,stih407-powerdown
+
+ '#reset-cells':
+ const: 1
+
+required:
+ - compatible
+ - '#reset-cells'
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/reset/stih407-resets.h>
+
+ powerdown: powerdown-controller {
+ compatible = "st,stih407-powerdown";
+ #reset-cells = <1>;
+ };
+
+ // Specifying powerdown control of devices:
+ st_dwc3: dwc3 {
+ resets = <&powerdown STIH407_USB3_POWERDOWN>;
+ };
--
2.30.2
On Thu, 07 Apr 2022 17:43:37 +0200, Philipp Zabel wrote:
> Convert the device tree bindings for the STMicroelectronics STi
> Peripheral Powerdown reset controller to YAML schema to allow
> participating in DT validation.
>
> Signed-off-by: Philipp Zabel <[email protected]>
> Cc: Srinivas Kandagatla <[email protected]>
> ---
> .../bindings/reset/st,sti-powerdown.txt | 45 -----------------
> .../bindings/reset/st,stih407-powerdown.yaml | 49 +++++++++++++++++++
> 2 files changed, 49 insertions(+), 45 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
> create mode 100644 Documentation/devicetree/bindings/reset/st,stih407-powerdown.yaml
>
Reviewed-by: Rob Herring <[email protected]>