We need to configure the sleep and idle mode of the CS pins for this
device. Add a DT property to do this so pins are in a proper state
during sleep (either hi-z, grounded, or pulled up to vdd).
Cc: Gwendal Grignou <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
---
.../devicetree/bindings/iio/proximity/semtech,sx9324.yaml | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml b/Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml
index d265eb5258c8..6cec3481c8b2 100644
--- a/Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml
+++ b/Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml
@@ -126,6 +126,14 @@ properties:
UINT_MAX (4294967295) represents infinite. Other values
represent 1-1/N.
+ semtech,cs-idle-sleep:
+ description:
+ State of CS pins during sleep mode and idle time.
+ enum:
+ - hz
+ - gnd
+ - vdd
+
semtech,int-comp-resistor:
description:
Internal resistor setting for compensation.
--
https://chromeos.dev
On Mon, May 02, 2022 at 05:41:55PM -0700, Stephen Boyd wrote:
> We need to configure the sleep and idle mode of the CS pins for this
> device. Add a DT property to do this so pins are in a proper state
> during sleep (either hi-z, grounded, or pulled up to vdd).
>
> Cc: Gwendal Grignou <[email protected]>
> Signed-off-by: Stephen Boyd <[email protected]>
> ---
> .../devicetree/bindings/iio/proximity/semtech,sx9324.yaml | 8 ++++++++
> 1 file changed, 8 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml b/Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml
> index d265eb5258c8..6cec3481c8b2 100644
> --- a/Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml
> +++ b/Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml
> @@ -126,6 +126,14 @@ properties:
> UINT_MAX (4294967295) represents infinite. Other values
> represent 1-1/N.
>
> + semtech,cs-idle-sleep:
> + description:
> + State of CS pins during sleep mode and idle time.
> + enum:
> + - hz
I was trying to figure out how Hertz was a pin state. 'hiz' or 'hi-z'
instead?
> + - gnd
> + - vdd
> +
> semtech,int-comp-resistor:
> description:
> Internal resistor setting for compensation.
> --
> https://chromeos.dev
>
>
Quoting Rob Herring (2022-05-03 07:18:44)
> On Mon, May 02, 2022 at 05:41:55PM -0700, Stephen Boyd wrote:
> > We need to configure the sleep and idle mode of the CS pins for this
> > device. Add a DT property to do this so pins are in a proper state
> > during sleep (either hi-z, grounded, or pulled up to vdd).
> >
> > Cc: Gwendal Grignou <[email protected]>
> > Signed-off-by: Stephen Boyd <[email protected]>
> > ---
> > .../devicetree/bindings/iio/proximity/semtech,sx9324.yaml | 8 ++++++++
> > 1 file changed, 8 insertions(+)
> >
> > diff --git a/Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml b/Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml
> > index d265eb5258c8..6cec3481c8b2 100644
> > --- a/Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml
> > +++ b/Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml
> > @@ -126,6 +126,14 @@ properties:
> > UINT_MAX (4294967295) represents infinite. Other values
> > represent 1-1/N.
> >
> > + semtech,cs-idle-sleep:
> > + description:
> > + State of CS pins during sleep mode and idle time.
> > + enum:
> > + - hz
>
> I was trying to figure out how Hertz was a pin state. 'hiz' or 'hi-z'
> instead?
Sure. I was following the datasheet that has "HZ" but hi-z is better.