Convert generic PWM bindings to DT schema format using json-schema. The
consumer bindings are split to separate file.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
---
Changes since v2:
1. Change also pwm-sprd.txt
Changes since v1:
1. Indent example with four spaces (more readable),
2. Change pattern for pwm nodes,
3. Remove $ref from #cells.
---
.../devicetree/bindings/clock/pwm-clock.txt | 2 +-
.../bindings/display/bridge/ti,sn65dsi86.txt | 2 +-
.../devicetree/bindings/display/ssd1307fb.txt | 2 +-
.../bindings/leds/backlight/pwm-backlight.txt | 2 +-
.../devicetree/bindings/leds/leds-pwm.txt | 2 +-
.../devicetree/bindings/mfd/max77693.txt | 2 +-
.../bindings/pwm/atmel-hlcdc-pwm.txt | 2 +-
.../devicetree/bindings/pwm/atmel-pwm.txt | 2 +-
.../devicetree/bindings/pwm/atmel-tcb-pwm.txt | 2 +-
.../bindings/pwm/brcm,bcm7038-pwm.txt | 2 +-
.../bindings/pwm/brcm,iproc-pwm.txt | 2 +-
.../devicetree/bindings/pwm/brcm,kona-pwm.txt | 2 +-
.../devicetree/bindings/pwm/img-pwm.txt | 2 +-
.../devicetree/bindings/pwm/imx-pwm.txt | 2 +-
.../devicetree/bindings/pwm/imx-tpm-pwm.txt | 2 +-
.../bindings/pwm/lpc1850-sct-pwm.txt | 2 +-
.../devicetree/bindings/pwm/mxs-pwm.txt | 2 +-
.../bindings/pwm/nvidia,tegra20-pwm.txt | 2 +-
.../bindings/pwm/nxp,pca9685-pwm.txt | 2 +-
.../devicetree/bindings/pwm/pwm-bcm2835.txt | 2 +-
.../devicetree/bindings/pwm/pwm-berlin.txt | 2 +-
.../bindings/pwm/pwm-consumers.yaml | 76 +++++++++++++++++++
.../devicetree/bindings/pwm/pwm-fsl-ftm.txt | 2 +-
.../devicetree/bindings/pwm/pwm-hibvt.txt | 2 +-
.../devicetree/bindings/pwm/pwm-lp3943.txt | 2 +-
.../devicetree/bindings/pwm/pwm-mediatek.txt | 2 +-
.../devicetree/bindings/pwm/pwm-meson.txt | 2 +-
.../devicetree/bindings/pwm/pwm-mtk-disp.txt | 2 +-
.../bindings/pwm/pwm-omap-dmtimer.txt | 2 +-
.../devicetree/bindings/pwm/pwm-rockchip.txt | 2 +-
.../devicetree/bindings/pwm/pwm-sifive.txt | 2 +-
.../devicetree/bindings/pwm/pwm-sprd.txt | 4 +-
.../devicetree/bindings/pwm/pwm-stm32-lp.txt | 2 +-
.../devicetree/bindings/pwm/pwm-stm32.txt | 2 +-
.../devicetree/bindings/pwm/pwm-tiecap.txt | 2 +-
.../devicetree/bindings/pwm/pwm-tiehrpwm.txt | 2 +-
.../devicetree/bindings/pwm/pwm-zx.txt | 2 +-
Documentation/devicetree/bindings/pwm/pwm.txt | 69 -----------------
.../devicetree/bindings/pwm/pwm.yaml | 29 +++++++
.../bindings/pwm/renesas,pwm-rcar.txt | 2 +-
.../bindings/pwm/renesas,tpu-pwm.txt | 4 +-
.../devicetree/bindings/pwm/spear-pwm.txt | 2 +-
.../devicetree/bindings/pwm/st,stmpe-pwm.txt | 2 +-
.../devicetree/bindings/pwm/ti,twl-pwm.txt | 2 +-
.../devicetree/bindings/pwm/ti,twl-pwmled.txt | 2 +-
.../devicetree/bindings/pwm/vt8500-pwm.txt | 2 +-
.../bindings/regulator/pwm-regulator.txt | 2 +-
.../devicetree/bindings/timer/ingenic,tcu.txt | 2 +-
48 files changed, 152 insertions(+), 116 deletions(-)
create mode 100644 Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
delete mode 100644 Documentation/devicetree/bindings/pwm/pwm.txt
create mode 100644 Documentation/devicetree/bindings/pwm/pwm.yaml
diff --git a/Documentation/devicetree/bindings/clock/pwm-clock.txt b/Documentation/devicetree/bindings/clock/pwm-clock.txt
index 83db876b3b90..8a791b6d76a9 100644
--- a/Documentation/devicetree/bindings/clock/pwm-clock.txt
+++ b/Documentation/devicetree/bindings/clock/pwm-clock.txt
@@ -3,7 +3,7 @@ Binding for an external clock signal driven by a PWM pin.
This binding uses the common clock binding[1] and the common PWM binding[2].
[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] Documentation/devicetree/bindings/pwm/pwm.txt
+[2] Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
Required properties:
- compatible : shall be "pwm-clock".
diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
index 0a3fbb53a16e..8ec4a7f2623a 100644
--- a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
+++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
@@ -21,7 +21,7 @@ Optional properties:
- #gpio-cells : Should be two. The first cell is the pin number and
the second cell is used to specify flags.
See ../../gpio/gpio.txt for more information.
-- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of
+- #pwm-cells : Should be one. See ../../pwm/pwm.yaml for description of
the cell formats.
- clock-names: should be "refclk"
diff --git a/Documentation/devicetree/bindings/display/ssd1307fb.txt b/Documentation/devicetree/bindings/display/ssd1307fb.txt
index 27333b9551b3..da9b28153a3c 100644
--- a/Documentation/devicetree/bindings/display/ssd1307fb.txt
+++ b/Documentation/devicetree/bindings/display/ssd1307fb.txt
@@ -37,7 +37,7 @@ Optional properties:
- solomon,area-color-enable: Display uses color mode
- solomon,low-power. Display runs in low power mode
-[0]: Documentation/devicetree/bindings/pwm/pwm.txt
+[0]: Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
Examples:
ssd1307: oled@3c {
diff --git a/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
index 64fa2fbd98c9..8dbbadd3af96 100644
--- a/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
+++ b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
@@ -28,7 +28,7 @@ Optional properties:
having to list out every possible value in the
brightness-level array.
-[0]: Documentation/devicetree/bindings/pwm/pwm.txt
+[0]: Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
[1]: Documentation/devicetree/bindings/gpio/gpio.txt
Example:
diff --git a/Documentation/devicetree/bindings/leds/leds-pwm.txt b/Documentation/devicetree/bindings/leds/leds-pwm.txt
index 6c6583c35f2f..aeaa250668d5 100644
--- a/Documentation/devicetree/bindings/leds/leds-pwm.txt
+++ b/Documentation/devicetree/bindings/leds/leds-pwm.txt
@@ -11,7 +11,7 @@ LED sub-node properties:
specify the period time to be used: <&phandle id period_ns>;
- pwm-names : (optional) Name to be used by the PWM subsystem for the PWM device
For the pwms and pwm-names property please refer to:
- Documentation/devicetree/bindings/pwm/pwm.txt
+ Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
- max-brightness : Maximum brightness possible for the LED
- active-low : (optional) For PWMs where the LED is wired to supply
rather than ground.
diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
index a3c60a7a3be1..1e6318695eb2 100644
--- a/Documentation/devicetree/bindings/mfd/max77693.txt
+++ b/Documentation/devicetree/bindings/mfd/max77693.txt
@@ -38,7 +38,7 @@ Optional properties:
PWM properties should be named "pwms". And number of cell is different
for each pwm device.
To get more information, please refer to documentation.
- [*] refer Documentation/devicetree/bindings/pwm/pwm.txt
+ [*] refer Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
- charger : Node configuring the charger driver.
If present, required properties:
diff --git a/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt
index cfda0d57d302..afa501bf7f94 100644
--- a/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt
@@ -10,7 +10,7 @@ Required properties:
- pinctrl-0: should contain the pinctrl states described by pinctrl
default.
- #pwm-cells: should be set to 3. This PWM chip use the default 3 cells
- bindings defined in pwm.txt in this directory.
+ bindings defined in pwm.yaml in this directory.
Example:
diff --git a/Documentation/devicetree/bindings/pwm/atmel-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt
index 591ecdd39c7b..fbb5325be1f0 100644
--- a/Documentation/devicetree/bindings/pwm/atmel-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt
@@ -7,7 +7,7 @@ Required properties:
- "atmel,sama5d2-pwm"
- "microchip,sam9x60-pwm"
- reg: physical base address and length of the controller's registers
- - #pwm-cells: Should be 3. See pwm.txt in this directory for a
+ - #pwm-cells: Should be 3. See pwm.yaml in this directory for a
description of the cells format.
Example:
diff --git a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
index 8031148bcf85..985fcc65f8c4 100644
--- a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
@@ -2,7 +2,7 @@ Atmel TCB PWM controller
Required properties:
- compatible: should be "atmel,tcb-pwm"
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
the cells format. The only third cell flag supported by this binding is
PWM_POLARITY_INVERTED.
- tc-block: The Timer Counter block to use as a PWM chip.
diff --git a/Documentation/devicetree/bindings/pwm/brcm,bcm7038-pwm.txt b/Documentation/devicetree/bindings/pwm/brcm,bcm7038-pwm.txt
index d9254a6da5ed..0e662d7f6bd1 100644
--- a/Documentation/devicetree/bindings/pwm/brcm,bcm7038-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/brcm,bcm7038-pwm.txt
@@ -4,7 +4,7 @@ Required properties:
- compatible: must be "brcm,bcm7038-pwm"
- reg: physical base address and length for this controller
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description
of the cells format
- clocks: a phandle to the reference clock for this block which is fed through
its internal variable clock frequency generator
diff --git a/Documentation/devicetree/bindings/pwm/brcm,iproc-pwm.txt b/Documentation/devicetree/bindings/pwm/brcm,iproc-pwm.txt
index 21f75bbd6dae..655f6cd4ef46 100644
--- a/Documentation/devicetree/bindings/pwm/brcm,iproc-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/brcm,iproc-pwm.txt
@@ -6,7 +6,7 @@ Required Properties :
- compatible: must be "brcm,iproc-pwm"
- reg: physical base address and length of the controller's registers
- clocks: phandle + clock specifier pair for the external clock
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a
description of the cells format.
Refer to clocks/clock-bindings.txt for generic clock consumer properties.
diff --git a/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt b/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt
index 8eae9fe7841c..c42eecfc81ed 100644
--- a/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt
@@ -6,7 +6,7 @@ Required Properties :
- compatible: should contain "brcm,kona-pwm"
- reg: physical base address and length of the controller's registers
- clocks: phandle + clock specifier pair for the external clock
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a
description of the cells format.
Refer to clocks/clock-bindings.txt for generic clock consumer properties.
diff --git a/Documentation/devicetree/bindings/pwm/img-pwm.txt b/Documentation/devicetree/bindings/pwm/img-pwm.txt
index fade5f26fcac..9db6de97317d 100644
--- a/Documentation/devicetree/bindings/pwm/img-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/img-pwm.txt
@@ -8,7 +8,7 @@ Required properties:
- clock-names: Must include the following entries.
- pwm: PWM operating clock.
- sys: PWM system interface clock.
- - #pwm-cells: Should be 2. See pwm.txt in this directory for the
+ - #pwm-cells: Should be 2. See pwm.yaml in this directory for the
description of the cells format.
- img,cr-periph: Must contain a phandle to the peripheral control
syscon node which contains PWM control registers.
diff --git a/Documentation/devicetree/bindings/pwm/imx-pwm.txt b/Documentation/devicetree/bindings/pwm/imx-pwm.txt
index c61bdf8cd41b..22f1c3d8b773 100644
--- a/Documentation/devicetree/bindings/pwm/imx-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/imx-pwm.txt
@@ -6,7 +6,7 @@ Required properties:
- "fsl,imx1-pwm" for PWM compatible with the one integrated on i.MX1
- "fsl,imx27-pwm" for PWM compatible with the one integrated on i.MX27
- reg: physical base address and length of the controller's registers
-- #pwm-cells: 2 for i.MX1 and 3 for i.MX27 and newer SoCs. See pwm.txt
+- #pwm-cells: 2 for i.MX1 and 3 for i.MX27 and newer SoCs. See pwm.yaml
in this directory for a description of the cells format.
- clocks : Clock specifiers for both ipg and per clocks.
- clock-names : Clock names should include both "ipg" and "per"
diff --git a/Documentation/devicetree/bindings/pwm/imx-tpm-pwm.txt b/Documentation/devicetree/bindings/pwm/imx-tpm-pwm.txt
index 3ba958d764ff..5bf20950a24e 100644
--- a/Documentation/devicetree/bindings/pwm/imx-tpm-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/imx-tpm-pwm.txt
@@ -3,7 +3,7 @@ Freescale i.MX TPM PWM controller
Required properties:
- compatible : Should be "fsl,imx7ulp-pwm".
- reg: Physical base address and length of the controller's registers.
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of the cells format.
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of the cells format.
- clocks : The clock provided by the SoC to drive the PWM.
- interrupts: The interrupt for the PWM controller.
diff --git a/Documentation/devicetree/bindings/pwm/lpc1850-sct-pwm.txt b/Documentation/devicetree/bindings/pwm/lpc1850-sct-pwm.txt
index 36e49d4325cd..43d9f4f08a2e 100644
--- a/Documentation/devicetree/bindings/pwm/lpc1850-sct-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/lpc1850-sct-pwm.txt
@@ -7,7 +7,7 @@ Required properties:
See ../clock/clock-bindings.txt for details.
- clock-names: Must include the following entries.
- pwm: PWM operating clock.
- - #pwm-cells: Should be 3. See pwm.txt in this directory for the description
+ - #pwm-cells: Should be 3. See pwm.yaml in this directory for the description
of the cells format.
Example:
diff --git a/Documentation/devicetree/bindings/pwm/mxs-pwm.txt b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt
index 96cdde5f6208..1b06f86a7091 100644
--- a/Documentation/devicetree/bindings/pwm/mxs-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt
@@ -3,7 +3,7 @@ Freescale MXS PWM controller
Required properties:
- compatible: should be "fsl,imx23-pwm"
- reg: physical base address and length of the controller's registers
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
the cells format.
- fsl,pwm-number: the number of PWM devices
diff --git a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt
index c57e11b8d937..0a69eadf44ce 100644
--- a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt
@@ -10,7 +10,7 @@ Required properties:
- "nvidia,tegra210-pwm", "nvidia,tegra20-pwm": for Tegra210
- "nvidia,tegra186-pwm": for Tegra186
- reg: physical base address and length of the controller's registers
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
the cells format.
- clocks: Must contain one entry, for the module clock.
See ../clocks/clock-bindings.txt for details.
diff --git a/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt
index f84ec9d291ea..f21b55c95738 100644
--- a/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt
@@ -3,7 +3,7 @@ NXP PCA9685 16-channel 12-bit PWM LED controller
Required properties:
- compatible: "nxp,pca9685-pwm"
- - #pwm-cells: Should be 2. See pwm.txt in this directory for a description of
+ - #pwm-cells: Should be 2. See pwm.yaml in this directory for a description of
the cells format.
The index 16 is the ALLCALL channel, that sets all PWM channels at the same
time.
diff --git a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt
index 8cf87d1bfca5..f5753b3f79df 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt
@@ -6,7 +6,7 @@ Required properties:
- clocks: This clock defines the base clock frequency of the PWM hardware
system, the period and the duty_cycle of the PWM signal is a multiple of
the base period.
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
the cells format.
Examples:
diff --git a/Documentation/devicetree/bindings/pwm/pwm-berlin.txt b/Documentation/devicetree/bindings/pwm/pwm-berlin.txt
index 82cbe16fcbbc..f01e993a498a 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-berlin.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-berlin.txt
@@ -4,7 +4,7 @@ Required properties:
- compatible: should be "marvell,berlin-pwm"
- reg: physical base address and length of the controller's registers
- clocks: phandle to the input clock
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
the cells format.
Example:
diff --git a/Documentation/devicetree/bindings/pwm/pwm-consumers.yaml b/Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
new file mode 100644
index 000000000000..39c844fe6338
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
@@ -0,0 +1,76 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pwm/pwm-consumers.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Specifying PWM information for devices
+
+maintainers:
+ - Thierry Reding <[email protected]>
+
+description: |
+ PWM properties should be named "pwms". The exact meaning of each pwms
+ property must be documented in the device tree binding for each device.
+ An optional property "pwm-names" may contain a list of strings to label
+ each of the PWM devices listed in the "pwms" property. If no "pwm-names"
+ property is given, the name of the user node will be used as fallback.
+
+ Drivers for devices that use more than a single PWM device can use the
+ "pwm-names" property to map the name of the PWM device requested by the
+ pwm_get() call to an index into the list given by the "pwms" property.
+
+properties:
+ pwms:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ description: |
+ Phandle to PWM controller node and pwm-specifier (controller specific).
+ pwm-specifier typically encodes the chip-relative PWM number and the PWM
+ period in nanoseconds.
+ Optionally, the pwm-specifier can encode a number of flags (defined in
+ <dt-bindings/pwm/pwm.h>) in a third cell:
+ - PWM_POLARITY_INVERTED: invert the PWM signal polarity
+
+ pwm-names:
+ $ref: /schemas/types.yaml#/definitions/string-array
+ description:
+ A list of strings to label each of the PWM devices listed in the "pwms"
+ property. If no "pwm-names" property is given, the name of the user node
+ will be used as fallback.
+
+required:
+ - pwms
+
+dependencies:
+ pwm-names: [ pwms ]
+
+examples:
+ - |
+ // The following example could be used to describe a PWM-based
+ // backlight device:
+
+ pwm: pwm {
+ #pwm-cells = <2>;
+ };
+
+ bl: backlight {
+ pwms = <&pwm 0 5000000>;
+ pwm-names = "backlight";
+ };
+
+ // Note that in the example above, specifying the "pwm-names" is redundant
+ // because the name "backlight" would be used as fallback anyway.
+
+ - |
+ // Example with optional PWM specifier for inverse polarity
+
+ #include <dt-bindings/pwm/pwm.h>
+
+ pwm2: pwm {
+ #pwm-cells = <3>;
+ };
+
+ backlight {
+ pwms = <&pwm2 0 5000000 PWM_POLARITY_INVERTED>;
+ pwm-names = "backlight";
+ };
diff --git a/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt
index 576ad002bc83..36532cd5ab25 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt
@@ -21,7 +21,7 @@ Required properties:
- "fsl,vf610-ftm-pwm" for PWM compatible with the one integrated on VF610
- "fsl,imx8qm-ftm-pwm" for PWM compatible with the one integrated on i.MX8QM
- reg: Physical base address and length of the controller's registers
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
the cells format.
- clock-names: Should include the following module clock source entries:
"ftm_sys" (module clock, also can be used as counter clock),
diff --git a/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt b/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt
index daedfef09bb6..54dbc2a0e648 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt
@@ -10,7 +10,7 @@ Required properties:
- reg: physical base address and length of the controller's registers.
- clocks: phandle and clock specifier of the PWM reference clock.
- resets: phandle and reset specifier for the PWM controller reset.
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
the cells format.
Example:
diff --git a/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt b/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt
index 7bd9d3b12ce1..f214305a8f5e 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt
@@ -2,7 +2,7 @@ TI/National Semiconductor LP3943 PWM controller
Required properties:
- compatible: "ti,lp3943-pwm"
- - #pwm-cells: Should be 2. See pwm.txt in this directory for a
+ - #pwm-cells: Should be 2. See pwm.yaml in this directory for a
description of the cells format.
Note that this hardware limits the period length to the
range 6250~1600000.
diff --git a/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt
index c8501530173c..69cae11d80a6 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt
@@ -9,7 +9,7 @@ Required properties:
- "mediatek,mt7629-pwm", "mediatek,mt7622-pwm": found on mt7629 SoC.
- "mediatek,mt8516-pwm": found on mt8516 SoC.
- reg: physical base address and length of the controller's registers.
- - #pwm-cells: must be 2. See pwm.txt in this directory for a description of
+ - #pwm-cells: must be 2. See pwm.yaml in this directory for a description of
the cell format.
- clocks: phandle and clock specifier of the PWM reference clock.
- clock-names: must contain the following, except for MT7628 which
diff --git a/Documentation/devicetree/bindings/pwm/pwm-meson.txt b/Documentation/devicetree/bindings/pwm/pwm-meson.txt
index 891632354065..bd02b0a1496f 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-meson.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-meson.txt
@@ -10,7 +10,7 @@ Required properties:
or "amlogic,meson-g12a-ee-pwm"
or "amlogic,meson-g12a-ao-pwm-ab"
or "amlogic,meson-g12a-ao-pwm-cd"
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
the cells format.
Optional properties:
diff --git a/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt b/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt
index 6f8af2bcc7b7..0521957c253f 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt
@@ -6,7 +6,7 @@ Required properties:
- "mediatek,mt6595-disp-pwm": found on mt6595 SoC.
- "mediatek,mt8173-disp-pwm": found on mt8173 SoC.
- reg: physical base address and length of the controller's registers.
- - #pwm-cells: must be 2. See pwm.txt in this directory for a description of
+ - #pwm-cells: must be 2. See pwm.yaml in this directory for a description of
the cell format.
- clocks: phandle and clock specifier of the PWM reference clock.
- clock-names: must contain the following:
diff --git a/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt b/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt
index 5ccfcc82da08..d722ae3be363 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt
@@ -4,7 +4,7 @@ Required properties:
- compatible: Shall contain "ti,omap-dmtimer-pwm".
- ti,timers: phandle to PWM capable OMAP timer. See timer/ti,timer.txt for info
about these timers.
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
the cells format.
Optional properties:
diff --git a/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt
index 2c5e52a5bede..f70956dea77b 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt
@@ -14,7 +14,7 @@ Required properties:
- For newer hardware (rk3328 and future socs): specified by name
- "pwm": This is used to derive the functional clock.
- "pclk": This is the APB bus clock.
- - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.txt in this directory
+ - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.yaml in this directory
for a description of the cell format.
Example:
diff --git a/Documentation/devicetree/bindings/pwm/pwm-sifive.txt b/Documentation/devicetree/bindings/pwm/pwm-sifive.txt
index 36447e3c9378..3d1dd7b06efc 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-sifive.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-sifive.txt
@@ -17,7 +17,7 @@ Required properties:
Please refer to sifive-blocks-ip-versioning.txt for details.
- reg: physical base address and length of the controller's registers
- clocks: Should contain a clock identifier for the PWM's parent clock.
-- #pwm-cells: Should be 3. See pwm.txt in this directory
+- #pwm-cells: Should be 3. See pwm.yaml in this directory
for a description of the cell format.
- interrupts: one interrupt per PWM channel
diff --git a/Documentation/devicetree/bindings/pwm/pwm-sprd.txt b/Documentation/devicetree/bindings/pwm/pwm-sprd.txt
index 16fa5a096206..83a8b732418c 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-sprd.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-sprd.txt
@@ -9,8 +9,8 @@ Required properties:
- clock-names: Should contain following entries:
"pwmn": used to derive the functional clock for PWM channel n (n range: 0 ~ 3).
"enablen": for PWM channel n enable clock (n range: 0 ~ 3).
-- #pwm-cells: Should be 2. See pwm.txt in this directory for a description of
- the cells format.
+- #pwm-cells: Should be 2. See pwm-consumers.yaml in this directory
+ for a description of the cells format.
Optional properties:
- assigned-clocks: Reference to the PWM clock entries.
diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt
index 6521bc44a74e..4cecb8e456b6 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt
@@ -8,7 +8,7 @@ See ../mfd/stm32-lptimer.txt for details about the parent node.
Required parameters:
- compatible: Must be "st,stm32-pwm-lp".
- #pwm-cells: Should be set to 3. This PWM chip uses the default 3 cells
- bindings defined in pwm.txt.
+ bindings defined in pwm.yaml.
Optional properties:
- pinctrl-names: Set to "default". An additional "sleep" state can be
diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt
index a8690bfa5e1f..f390a5ba3d3a 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-stm32.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt
@@ -9,7 +9,7 @@ Required parameters:
- pinctrl-0: List of phandles pointing to pin configuration nodes for PWM module.
For Pinctrl properties see ../pinctrl/pinctrl-bindings.txt
- #pwm-cells: Should be set to 3. This PWM chip uses the default 3 cells
- bindings defined in pwm.txt.
+ bindings defined in pwm.yaml.
Optional parameters:
- st,breakinput: One or two <index level filter> to describe break input configurations.
diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
index b9a1d7402128..c7c4347a769a 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
@@ -8,7 +8,7 @@ Required properties:
for dra746 - compatible = "ti,dra746-ecap", "ti,am3352-ecap";
for 66ak2g - compatible = "ti,k2g-ecap", "ti,am3352-ecap";
for am654 - compatible = "ti,am654-ecap", "ti,am3352-ecap";
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
the cells format. The PWM channel index ranges from 0 to 4. The only third
cell flag supported by this binding is PWM_POLARITY_INVERTED.
- reg: physical base address and size of the registers map.
diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
index 31c4577157dd..c7e28f6d28be 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
@@ -7,7 +7,7 @@ Required properties:
for am654 - compatible = "ti,am654-ehrpwm", "ti-am3352-ehrpwm";
for da850 - compatible = "ti,da850-ehrpwm", "ti-am3352-ehrpwm", "ti,am33xx-ehrpwm";
for dra746 - compatible = "ti,dra746-ehrpwm", "ti-am3352-ehrpwm";
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
the cells format. The only third cell flag supported by this binding is
PWM_POLARITY_INVERTED.
- reg: physical base address and size of the registers map.
diff --git a/Documentation/devicetree/bindings/pwm/pwm-zx.txt b/Documentation/devicetree/bindings/pwm/pwm-zx.txt
index a6bcc75c9164..3c8fe7aa8269 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-zx.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-zx.txt
@@ -7,7 +7,7 @@ Required properties:
- clock-names: "pclk" for PCLK, "wclk" for WCLK to the PWM controller. The
PCLK is for register access, while WCLK is the reference clock for
calculating period and duty cycles.
- - #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+ - #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of
the cells format.
Example:
diff --git a/Documentation/devicetree/bindings/pwm/pwm.txt b/Documentation/devicetree/bindings/pwm/pwm.txt
deleted file mode 100644
index 8556263b8502..000000000000
--- a/Documentation/devicetree/bindings/pwm/pwm.txt
+++ /dev/null
@@ -1,69 +0,0 @@
-Specifying PWM information for devices
-======================================
-
-1) PWM user nodes
------------------
-
-PWM users should specify a list of PWM devices that they want to use
-with a property containing a 'pwm-list':
-
- pwm-list ::= <single-pwm> [pwm-list]
- single-pwm ::= <pwm-phandle> <pwm-specifier>
- pwm-phandle : phandle to PWM controller node
- pwm-specifier : array of #pwm-cells specifying the given PWM
- (controller specific)
-
-PWM properties should be named "pwms". The exact meaning of each pwms
-property must be documented in the device tree binding for each device.
-An optional property "pwm-names" may contain a list of strings to label
-each of the PWM devices listed in the "pwms" property. If no "pwm-names"
-property is given, the name of the user node will be used as fallback.
-
-Drivers for devices that use more than a single PWM device can use the
-"pwm-names" property to map the name of the PWM device requested by the
-pwm_get() call to an index into the list given by the "pwms" property.
-
-The following example could be used to describe a PWM-based backlight
-device:
-
- pwm: pwm {
- #pwm-cells = <2>;
- };
-
- [...]
-
- bl: backlight {
- pwms = <&pwm 0 5000000>;
- pwm-names = "backlight";
- };
-
-Note that in the example above, specifying the "pwm-names" is redundant
-because the name "backlight" would be used as fallback anyway.
-
-pwm-specifier typically encodes the chip-relative PWM number and the PWM
-period in nanoseconds.
-
-Optionally, the pwm-specifier can encode a number of flags (defined in
-<dt-bindings/pwm/pwm.h>) in a third cell:
-- PWM_POLARITY_INVERTED: invert the PWM signal polarity
-
-Example with optional PWM specifier for inverse polarity
-
- bl: backlight {
- pwms = <&pwm 0 5000000 PWM_POLARITY_INVERTED>;
- pwm-names = "backlight";
- };
-
-2) PWM controller nodes
------------------------
-
-PWM controller nodes must specify the number of cells used for the
-specifier using the '#pwm-cells' property.
-
-An example PWM controller might look like this:
-
- pwm: pwm@7000a000 {
- compatible = "nvidia,tegra20-pwm";
- reg = <0x7000a000 0x100>;
- #pwm-cells = <2>;
- };
diff --git a/Documentation/devicetree/bindings/pwm/pwm.yaml b/Documentation/devicetree/bindings/pwm/pwm.yaml
new file mode 100644
index 000000000000..aad99d505bb0
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm.yaml
@@ -0,0 +1,29 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pwm/pwm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PWM controllers (providers)
+
+maintainers:
+ - Thierry Reding <[email protected]>
+
+properties:
+ $nodename:
+ pattern: "^pwm(@.*|-[0-9a-f])*$"
+
+ "#pwm-cells":
+ description:
+ Number of cells in a PWM specifier.
+
+required:
+ - "#pwm-cells"
+
+examples:
+ - |
+ pwm: pwm@7000a000 {
+ compatible = "nvidia,tegra20-pwm";
+ reg = <0x7000a000 0x100>;
+ #pwm-cells = <2>;
+ };
diff --git a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt
index fbd6a4f943ce..a29137869f7a 100644
--- a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt
+++ b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt
@@ -20,7 +20,7 @@ Required Properties:
- "renesas,pwm-r8a77990": for R-Car E3
- "renesas,pwm-r8a77995": for R-Car D3
- reg: base address and length of the registers block for the PWM.
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
the cells format.
- clocks: clock phandle and specifier pair.
- pinctrl-0: phandle, referring to a default pin configuration node.
diff --git a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt
index 848a92b53d81..966994968069 100644
--- a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt
@@ -19,11 +19,11 @@ Required Properties:
- reg: Base address and length of each memory resource used by the PWM
controller hardware module.
- - #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+ - #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
the cells format. The only third cell flag supported by this binding is
PWM_POLARITY_INVERTED.
-Please refer to pwm.txt in this directory for details of the common PWM bindings
+Please refer to pwm-consumers.yaml in this directory for details of the common PWM bindings
used by client devices.
Example: R8A7740 (R-Mobile A1) TPU controller node
diff --git a/Documentation/devicetree/bindings/pwm/spear-pwm.txt b/Documentation/devicetree/bindings/pwm/spear-pwm.txt
index b486de2c3fe3..95894128b62f 100644
--- a/Documentation/devicetree/bindings/pwm/spear-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/spear-pwm.txt
@@ -5,7 +5,7 @@ Required properties:
- "st,spear320-pwm"
- "st,spear1340-pwm"
- reg: physical base address and length of the controller's registers
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
the cells format.
Example:
diff --git a/Documentation/devicetree/bindings/pwm/st,stmpe-pwm.txt b/Documentation/devicetree/bindings/pwm/st,stmpe-pwm.txt
index cb209646bf13..f401316e0248 100644
--- a/Documentation/devicetree/bindings/pwm/st,stmpe-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/st,stmpe-pwm.txt
@@ -7,7 +7,7 @@ subdevices of the STMPE MFD device.
Required properties:
- compatible: should be:
- "st,stmpe-pwm"
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
the cells format.
Example:
diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt
index 4e32bee11201..d97ca1964e94 100644
--- a/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt
@@ -6,7 +6,7 @@ On TWL6030 series: PWM0 and PWM1
Required properties:
- compatible: "ti,twl4030-pwm" or "ti,twl6030-pwm"
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
the cells format.
Example:
diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt
index 9f4b46090782..31ca1b032ef0 100644
--- a/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt
+++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt
@@ -6,7 +6,7 @@ On TWL6030 series: LED PWM (mainly used as charging indicator LED)
Required properties:
- compatible: "ti,twl4030-pwmled" or "ti,twl6030-pwmled"
-- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of
the cells format.
Example:
diff --git a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt
index a76390e6df2e..4fba93ce1985 100644
--- a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt
@@ -3,7 +3,7 @@ VIA/Wondermedia VT8500/WM8xxx series SoC PWM controller
Required properties:
- compatible: should be "via,vt8500-pwm"
- reg: physical base address and length of the controller's registers
-- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of
the cells format. The only third cell flag supported by this binding is
PWM_POLARITY_INVERTED.
- clocks: phandle to the PWM source clock
diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt
index 3d78d507e29f..252edcc2e381 100644
--- a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt
@@ -27,7 +27,7 @@ Required properties:
--------------------
- compatible: Should be "pwm-regulator"
-- pwms: PWM specification (See: ../pwm/pwm.txt)
+- pwms: PWM specification (See: ../pwm/pwm-consumers.yaml)
Only required for Voltage Table Mode:
- voltage-table: Voltage and Duty-Cycle table consisting of 2 cells
diff --git a/Documentation/devicetree/bindings/timer/ingenic,tcu.txt b/Documentation/devicetree/bindings/timer/ingenic,tcu.txt
index 5a4b9ddd9470..0c7bd51c19eb 100644
--- a/Documentation/devicetree/bindings/timer/ingenic,tcu.txt
+++ b/Documentation/devicetree/bindings/timer/ingenic,tcu.txt
@@ -42,7 +42,7 @@ Required properties:
- compatible: Must be one of:
* ingenic,jz4740-pwm
* ingenic,jz4725b-pwm
-- #pwm-cells: Should be 3. See ../pwm/pwm.txt for a description of the cell
+- #pwm-cells: Should be 3. See ../pwm/pwm.yaml for a description of the cell
format.
- clocks: List of phandle & clock specifiers for the TCU clocks.
- clock-names: List of name strings for the TCU clocks.
--
2.17.1
On Wed, 2 Oct 2019, Krzysztof Kozlowski wrote:
> Convert generic PWM bindings to DT schema format using json-schema. The
> consumer bindings are split to separate file.
>
> Signed-off-by: Krzysztof Kozlowski <[email protected]>
>
> ---
>
[ ... ]
> diff --git a/Documentation/devicetree/bindings/pwm/pwm-sifive.txt b/Documentation/devicetree/bindings/pwm/pwm-sifive.txt
> index 36447e3c9378..3d1dd7b06efc 100644
> --- a/Documentation/devicetree/bindings/pwm/pwm-sifive.txt
> +++ b/Documentation/devicetree/bindings/pwm/pwm-sifive.txt
> @@ -17,7 +17,7 @@ Required properties:
> Please refer to sifive-blocks-ip-versioning.txt for details.
> - reg: physical base address and length of the controller's registers
> - clocks: Should contain a clock identifier for the PWM's parent clock.
> -- #pwm-cells: Should be 3. See pwm.txt in this directory
> +- #pwm-cells: Should be 3. See pwm.yaml in this directory
> for a description of the cell format.
> - interrupts: one interrupt per PWM channel
For the SiFive PWM driver documentation:
Acked-by: Paul Walmsley <[email protected]>
- Paul
On Wed, Oct 02, 2019 at 06:40:46PM +0200, Krzysztof Kozlowski wrote:
> Convert generic PWM bindings to DT schema format using json-schema. The
> consumer bindings are split to separate file.
>
> Signed-off-by: Krzysztof Kozlowski <[email protected]>
>
> ---
>
> Changes since v2:
> 1. Change also pwm-sprd.txt
>
> Changes since v1:
> 1. Indent example with four spaces (more readable),
> 2. Change pattern for pwm nodes,
> 3. Remove $ref from #cells.
> ---
> diff --git a/Documentation/devicetree/bindings/pwm/pwm-consumers.yaml b/Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
> new file mode 100644
> index 000000000000..39c844fe6338
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pwm/pwm-consumers.yaml
> @@ -0,0 +1,76 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pwm/pwm-consumers.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Specifying PWM information for devices
> +
> +maintainers:
> + - Thierry Reding <[email protected]>
> +
> +description: |
> + PWM properties should be named "pwms". The exact meaning of each pwms
> + property must be documented in the device tree binding for each device.
> + An optional property "pwm-names" may contain a list of strings to label
> + each of the PWM devices listed in the "pwms" property. If no "pwm-names"
> + property is given, the name of the user node will be used as fallback.
> +
> + Drivers for devices that use more than a single PWM device can use the
> + "pwm-names" property to map the name of the PWM device requested by the
> + pwm_get() call to an index into the list given by the "pwms" property.
> +
> +properties:
> + pwms:
> + $ref: /schemas/types.yaml#/definitions/phandle-array
> + description: |
> + Phandle to PWM controller node and pwm-specifier (controller specific).
> + pwm-specifier typically encodes the chip-relative PWM number and the PWM
> + period in nanoseconds.
> + Optionally, the pwm-specifier can encode a number of flags (defined in
> + <dt-bindings/pwm/pwm.h>) in a third cell:
> + - PWM_POLARITY_INVERTED: invert the PWM signal polarity
> +
> + pwm-names:
> + $ref: /schemas/types.yaml#/definitions/string-array
> + description:
> + A list of strings to label each of the PWM devices listed in the "pwms"
> + property. If no "pwm-names" property is given, the name of the user node
> + will be used as fallback.
> +
> +required:
> + - pwms
This schema is never applied because it has no 'select' which is only
automatic for $nodename or compatible. You could include this from other
schemas, but why? Any consumer still has to list these properties to
define their specific constraints.
We already have a schema in dtschema for consumer side. It's just
missing descriptions which needs relicensing from this.
> +
> +dependencies:
> + pwm-names: [ pwms ]