The panel uses a Focaltech FT8006p, the touch part is handled by the already
existing edt-ft5x06. It can be found in e.g. the Librem 5.
Changes from v2:
- Due to review comments by Sam Ravnborg, thanks!
https://lore.kernel.org/lkml/[email protected]/
- Drop unused header
- Use newline before comment
- Add Reviewed/Acked-by by Sam Ravnborg, thanks!
https://lore.kernel.org/lkml/[email protected]/
https://lore.kernel.org/lkml/[email protected]/
https://lore.kernel.org/lkml/[email protected]/
Changes from v1:
- Due to review comments by Sam Ravnborg, thanks!
https://lore.kernel.org/dri-devel/[email protected]/
- Don't preserve newlines with '|' in description
- Use reset-gpios and backlight from panel-common.yaml
- Reindent example
https://lore.kernel.org/dri-devel/[email protected]/
- Drop unused includes
- Use dev_* instead of DRM_* for printing
- Turn off regulators in reverse order from enable
- Silence errors in mantix_{shutdown,remove}
- Drop duplicate mipi_dsi_dcs_enter_sleep_mode()
https://lore.kernel.org/dri-devel/[email protected]/
- Use dev_err_probe()
- Add delays when turning off panel as suggested by the data sheet
This series is against next-20200814.
Guido Günther (3):
dt-bindings: vendor-prefixes: Add mantix vendor prefix
dt-bindings: Add Mantix MLAF057WE51-X panel bindings
drm/panel: Add panel driver for the Mantix MLAF057WE51-X DSI panel
.../display/panel/mantix,mlaf057we51-x.yaml | 70 ++++
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
MAINTAINERS | 7 +
drivers/gpu/drm/panel/Kconfig | 11 +
drivers/gpu/drm/panel/Makefile | 1 +
.../gpu/drm/panel/panel-mantix-mlaf057we51.c | 328 ++++++++++++++++++
6 files changed, 419 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/mantix,mlaf057we51-x.yaml
create mode 100644 drivers/gpu/drm/panel/panel-mantix-mlaf057we51.c
--
2.26.2
The panel uses a Focaltech FT8006p, the touch part is handled by the
already existing edt-ft5x06.
Signed-off-by: Guido Günther <[email protected]>
Reviewed-by: Sam Ravnborg <[email protected]>
---
MAINTAINERS | 7 +
drivers/gpu/drm/panel/Kconfig | 11 +
drivers/gpu/drm/panel/Makefile | 1 +
.../gpu/drm/panel/panel-mantix-mlaf057we51.c | 328 ++++++++++++++++++
4 files changed, 347 insertions(+)
create mode 100644 drivers/gpu/drm/panel/panel-mantix-mlaf057we51.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 83ba7b62651f7..7dfe4cc3d4ec8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5474,6 +5474,13 @@ S: Maintained
F: drivers/gpu/drm/panel/panel-lvds.c
F: Documentation/devicetree/bindings/display/panel/lvds.yaml
+DRM DRIVER FOR MANTIX MLAF057WE51 PANELS
+M: Guido Günther <[email protected]>
+R: Purism Kernel Team <[email protected]>
+S: Maintained
+F: Documentation/devicetree/bindings/display/panel/mantix,mlaf057we51-x.yaml
+F: drivers/gpu/drm/panel/panel-mantix-mlaf057we51.c
+
DRM DRIVER FOR MATROX G200/G400 GRAPHICS CARDS
S: Orphan / Obsolete
F: drivers/gpu/drm/mga/
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index de2f2a452be55..8d97d07c58713 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -217,6 +217,17 @@ config DRM_PANEL_NOVATEK_NT39016
Say Y here if you want to enable support for the panels built
around the Novatek NT39016 display controller.
+config DRM_PANEL_MANTIX_MLAF057WE51
+ tristate "Mantix MLAF057WE51-X MIPI-DSI LCD panel"
+ depends on OF
+ depends on DRM_MIPI_DSI
+ depends on BACKLIGHT_CLASS_DEVICE
+ help
+ Say Y here if you want to enable support for the Mantix
+ MLAF057WE51-X MIPI DSI panel as e.g. used in the Librem 5. It
+ has a resolution of 720x1440 pixels, a built in backlight and touch
+ controller.
+
config DRM_PANEL_OLIMEX_LCD_OLINUXINO
tristate "Olimex LCD-OLinuXino panel"
depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index e45ceac6286fd..15a4e77529514 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -20,6 +20,7 @@ obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o
obj-$(CONFIG_DRM_PANEL_NEC_NL8048HL11) += panel-nec-nl8048hl11.o
obj-$(CONFIG_DRM_PANEL_NOVATEK_NT35510) += panel-novatek-nt35510.o
obj-$(CONFIG_DRM_PANEL_NOVATEK_NT39016) += panel-novatek-nt39016.o
+obj-$(CONFIG_DRM_PANEL_MANTIX_MLAF057WE51) += panel-mantix-mlaf057we51.o
obj-$(CONFIG_DRM_PANEL_OLIMEX_LCD_OLINUXINO) += panel-olimex-lcd-olinuxino.o
obj-$(CONFIG_DRM_PANEL_ORISETECH_OTM8009A) += panel-orisetech-otm8009a.o
obj-$(CONFIG_DRM_PANEL_OSD_OSD101T2587_53TS) += panel-osd-osd101t2587-53ts.o
diff --git a/drivers/gpu/drm/panel/panel-mantix-mlaf057we51.c b/drivers/gpu/drm/panel/panel-mantix-mlaf057we51.c
new file mode 100644
index 0000000000000..3482e28e30fc9
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-mantix-mlaf057we51.c
@@ -0,0 +1,328 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Mantix MLAF057WE51 5.7" MIPI-DSI panel driver
+ *
+ * Copyright (C) Purism SPC 2020
+ */
+
+#include <linux/backlight.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/regulator/consumer.h>
+
+#include <video/mipi_display.h>
+
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+
+#define DRV_NAME "panel-mantix-mlaf057we51"
+
+/* Manufacturer specific Commands send via DSI */
+#define MANTIX_CMD_OTP_STOP_RELOAD_MIPI 0x41
+#define MANTIX_CMD_INT_CANCEL 0x4C
+
+struct mantix {
+ struct device *dev;
+ struct drm_panel panel;
+ struct gpio_desc *reset_gpio;
+
+ struct regulator *avdd;
+ struct regulator *avee;
+ struct regulator *vddi;
+};
+
+static inline struct mantix *panel_to_mantix(struct drm_panel *panel)
+{
+ return container_of(panel, struct mantix, panel);
+}
+
+#define dsi_generic_write_seq(dsi, seq...) do { \
+ static const u8 d[] = { seq }; \
+ int ret; \
+ ret = mipi_dsi_generic_write(dsi, d, ARRAY_SIZE(d)); \
+ if (ret < 0) \
+ return ret; \
+ } while (0)
+
+static int mantix_init_sequence(struct mantix *ctx)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+ struct device *dev = ctx->dev;
+
+ /*
+ * Init sequence was supplied by the panel vendor.
+ */
+ dsi_generic_write_seq(dsi, MANTIX_CMD_OTP_STOP_RELOAD_MIPI, 0x5A);
+
+ dsi_generic_write_seq(dsi, MANTIX_CMD_INT_CANCEL, 0x03);
+ dsi_generic_write_seq(dsi, MANTIX_CMD_OTP_STOP_RELOAD_MIPI, 0x5A, 0x03);
+ dsi_generic_write_seq(dsi, 0x80, 0xA9, 0x00);
+
+ dsi_generic_write_seq(dsi, MANTIX_CMD_OTP_STOP_RELOAD_MIPI, 0x5A, 0x09);
+ dsi_generic_write_seq(dsi, 0x80, 0x64, 0x00, 0x64, 0x00, 0x00);
+ msleep(20);
+
+ dev_dbg(dev, "Panel init sequence done\n");
+ return 0;
+}
+
+static int mantix_enable(struct drm_panel *panel)
+{
+ struct mantix *ctx = panel_to_mantix(panel);
+ struct device *dev = ctx->dev;
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(dev);
+ int ret;
+
+ ret = mantix_init_sequence(ctx);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Panel init sequence failed: %d\n", ret);
+ return ret;
+ }
+
+ ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
+ if (ret < 0) {
+ dev_err(dev, "Failed to exit sleep mode\n");
+ return ret;
+ }
+ msleep(20);
+
+ ret = mipi_dsi_dcs_set_display_on(dsi);
+ if (ret)
+ return ret;
+ usleep_range(10000, 12000);
+
+ ret = mipi_dsi_turn_on_peripheral(dsi);
+ if (ret < 0) {
+ dev_err(dev, "Failed to turn on peripheral\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int mantix_disable(struct drm_panel *panel)
+{
+ struct mantix *ctx = panel_to_mantix(panel);
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+ int ret;
+
+ ret = mipi_dsi_dcs_set_display_off(dsi);
+ if (ret < 0)
+ dev_err(ctx->dev, "Failed to turn off the display: %d\n", ret);
+
+ ret = mipi_dsi_dcs_enter_sleep_mode(dsi);
+ if (ret < 0)
+ dev_err(ctx->dev, "Failed to enter sleep mode: %d\n", ret);
+
+
+ return 0;
+}
+
+static int mantix_unprepare(struct drm_panel *panel)
+{
+ struct mantix *ctx = panel_to_mantix(panel);
+
+ regulator_disable(ctx->avee);
+ regulator_disable(ctx->avdd);
+ /* T11 */
+ usleep_range(5000, 6000);
+ regulator_disable(ctx->vddi);
+ /* T14 */
+ msleep(50);
+
+ return 0;
+}
+
+static int mantix_prepare(struct drm_panel *panel)
+{
+ struct mantix *ctx = panel_to_mantix(panel);
+ int ret;
+
+ /* Focaltech FT8006P, section 7.3.1 and 7.3.4 */
+ dev_dbg(ctx->dev, "Resetting the panel\n");
+ ret = regulator_enable(ctx->vddi);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Failed to enable vddi supply: %d\n", ret);
+ return ret;
+ }
+
+ /* T1 + T2 */
+ usleep_range(8000, 10000);
+
+ ret = regulator_enable(ctx->avdd);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Failed to enable avdd supply: %d\n", ret);
+ return ret;
+ }
+
+ /* T2d */
+ usleep_range(3500, 4000);
+ ret = regulator_enable(ctx->avee);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Failed to enable avee supply: %d\n", ret);
+ return ret;
+ }
+
+ /* T3+T5 */
+ usleep_range(10000, 12000);
+
+ gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+ usleep_range(5150, 7000);
+
+ gpiod_set_value_cansleep(ctx->reset_gpio, 0);
+
+ /* T6 */
+ msleep(50);
+
+ return 0;
+}
+
+static const struct drm_display_mode default_mode = {
+ .hdisplay = 720,
+ .hsync_start = 720 + 45,
+ .hsync_end = 720 + 45 + 14,
+ .htotal = 720 + 45 + 14 + 25,
+ .vdisplay = 1440,
+ .vsync_start = 1440 + 130,
+ .vsync_end = 1440 + 130 + 8,
+ .vtotal = 1440 + 130 + 8 + 106,
+ .clock = 85298,
+ .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+ .width_mm = 65,
+ .height_mm = 130,
+};
+
+static int mantix_get_modes(struct drm_panel *panel,
+ struct drm_connector *connector)
+{
+ struct mantix *ctx = panel_to_mantix(panel);
+ struct drm_display_mode *mode;
+
+ mode = drm_mode_duplicate(connector->dev, &default_mode);
+ if (!mode) {
+ dev_err(ctx->dev, "Failed to add mode %ux%u@%u\n",
+ default_mode.hdisplay, default_mode.vdisplay,
+ drm_mode_vrefresh(mode));
+ return -ENOMEM;
+ }
+
+ drm_mode_set_name(mode);
+
+ mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+ connector->display_info.width_mm = mode->width_mm;
+ connector->display_info.height_mm = mode->height_mm;
+ drm_mode_probed_add(connector, mode);
+
+ return 1;
+}
+
+static const struct drm_panel_funcs mantix_drm_funcs = {
+ .disable = mantix_disable,
+ .unprepare = mantix_unprepare,
+ .prepare = mantix_prepare,
+ .enable = mantix_enable,
+ .get_modes = mantix_get_modes,
+};
+
+static int mantix_probe(struct mipi_dsi_device *dsi)
+{
+ struct device *dev = &dsi->dev;
+ struct mantix *ctx;
+ int ret;
+
+ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+ if (!ctx)
+ return -ENOMEM;
+
+ ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(ctx->reset_gpio)) {
+ dev_err(dev, "cannot get reset gpio\n");
+ return PTR_ERR(ctx->reset_gpio);
+ }
+
+ mipi_dsi_set_drvdata(dsi, ctx);
+ ctx->dev = dev;
+
+ dsi->lanes = 4;
+ dsi->format = MIPI_DSI_FMT_RGB888;
+ dsi->mode_flags = MIPI_DSI_MODE_VIDEO |
+ MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
+
+ ctx->avdd = devm_regulator_get(dev, "avdd");
+ if (IS_ERR(ctx->avdd))
+ return dev_err_probe(dev, PTR_ERR(ctx->avdd), "Failed to request avdd regulator\n");
+
+ ctx->avee = devm_regulator_get(dev, "avee");
+ if (IS_ERR(ctx->avee))
+ return dev_err_probe(dev, PTR_ERR(ctx->avee), "Failed to request avee regulator\n");
+
+ ctx->vddi = devm_regulator_get(dev, "vddi");
+ if (IS_ERR(ctx->vddi))
+ return dev_err_probe(dev, PTR_ERR(ctx->vddi), "Failed to request vddi regulator\n");
+
+ drm_panel_init(&ctx->panel, dev, &mantix_drm_funcs,
+ DRM_MODE_CONNECTOR_DSI);
+
+ ret = drm_panel_of_backlight(&ctx->panel);
+ if (ret)
+ return ret;
+
+ drm_panel_add(&ctx->panel);
+
+ ret = mipi_dsi_attach(dsi);
+ if (ret < 0) {
+ dev_err(dev, "mipi_dsi_attach failed (%d). Is host ready?\n", ret);
+ drm_panel_remove(&ctx->panel);
+ return ret;
+ }
+
+ dev_info(dev, "%ux%u@%u %ubpp dsi %udl - ready\n",
+ default_mode.hdisplay, default_mode.vdisplay,
+ drm_mode_vrefresh(&default_mode),
+ mipi_dsi_pixel_format_to_bpp(dsi->format), dsi->lanes);
+
+ return 0;
+}
+
+static void mantix_shutdown(struct mipi_dsi_device *dsi)
+{
+ struct mantix *ctx = mipi_dsi_get_drvdata(dsi);
+
+ drm_panel_unprepare(&ctx->panel);
+ drm_panel_disable(&ctx->panel);
+}
+
+static int mantix_remove(struct mipi_dsi_device *dsi)
+{
+ struct mantix *ctx = mipi_dsi_get_drvdata(dsi);
+
+ mantix_shutdown(dsi);
+
+ mipi_dsi_detach(dsi);
+ drm_panel_remove(&ctx->panel);
+
+ return 0;
+}
+
+static const struct of_device_id mantix_of_match[] = {
+ { .compatible = "mantix,mlaf057we51-x" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mantix_of_match);
+
+static struct mipi_dsi_driver mantix_driver = {
+ .probe = mantix_probe,
+ .remove = mantix_remove,
+ .shutdown = mantix_shutdown,
+ .driver = {
+ .name = DRV_NAME,
+ .of_match_table = mantix_of_match,
+ },
+};
+module_mipi_dsi_driver(mantix_driver);
+
+MODULE_AUTHOR("Guido Günther <[email protected]>");
+MODULE_DESCRIPTION("DRM driver for Mantix MLAF057WE51-X MIPI DSI panel");
+MODULE_LICENSE("GPL v2");
--
2.26.2
Add prefix for Mantix Display Technology Co.,Ltd.
Signed-off-by: Guido Günther <[email protected]>
Acked-by: Sam Ravnborg <[email protected]>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 2baee2c817c1a..59d4c8b068c4d 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -611,6 +611,8 @@ patternProperties:
description: Linux Automation GmbH
"^macnica,.*":
description: Macnica Americas
+ "^mantix,.*":
+ description: Mantix Display Technology Co.,Ltd.
"^mapleboard,.*":
description: Mapleboard.org
"^marvell,.*":
--
2.26.2
The panel uses a Focaltech FT8006p, the touch part is handled by the
already existing edt-ft5x06.
Signed-off-by: Guido Günther <[email protected]>
Reviewed-by: Sam Ravnborg <[email protected]>
---
.../display/panel/mantix,mlaf057we51-x.yaml | 70 +++++++++++++++++++
1 file changed, 70 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/mantix,mlaf057we51-x.yaml
diff --git a/Documentation/devicetree/bindings/display/panel/mantix,mlaf057we51-x.yaml b/Documentation/devicetree/bindings/display/panel/mantix,mlaf057we51-x.yaml
new file mode 100644
index 0000000000000..937323cc9aaac
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/mantix,mlaf057we51-x.yaml
@@ -0,0 +1,70 @@
+# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/mantix,mlaf057we51-x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mantix MLAF057WE51-X 5.7" 720x1440 TFT LCD panel
+
+maintainers:
+ - Guido Günther <[email protected]>
+
+description:
+ Mantix MLAF057WE51 X is a 720x1440 TFT LCD panel connected using
+ a MIPI-DSI video interface.
+
+allOf:
+ - $ref: panel-common.yaml#
+
+properties:
+ compatible:
+ enum:
+ - mantix,mlaf057we51-x
+
+ port: true
+ reg:
+ maxItems: 1
+ description: DSI virtual channel
+
+ avdd-supply:
+ description: Positive analog power supply
+
+ avee-supply:
+ description: Negative analog power supply
+
+ vddi-supply:
+ description: 1.8V I/O voltage supply
+
+ reset-gpios: true
+
+ backlight: true
+
+required:
+ - compatible
+ - reg
+ - avdd-supply
+ - avee-supply
+ - vddi-supply
+ - reset-gpios
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ dsi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ panel@0 {
+ compatible = "mantix,mlaf057we51-x";
+ reg = <0>;
+ avdd-supply = <®_avdd>;
+ avee-supply = <®_avee>;
+ vddi-supply = <®_1v8_p>;
+ reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+ backlight = <&backlight>;
+ };
+ };
+
+...
--
2.26.2
Hi Guido.
On Mon, Aug 17, 2020 at 10:14:33AM +0200, Guido G?nther wrote:
>
> The panel uses a Focaltech FT8006p, the touch part is handled by the already
> existing edt-ft5x06. It can be found in e.g. the Librem 5.
>
> Changes from v2:
> - Due to review comments by Sam Ravnborg, thanks!
> https://lore.kernel.org/lkml/[email protected]/
> - Drop unused header
> - Use newline before comment
> - Add Reviewed/Acked-by by Sam Ravnborg, thanks!
> https://lore.kernel.org/lkml/[email protected]/
> https://lore.kernel.org/lkml/[email protected]/
> https://lore.kernel.org/lkml/[email protected]/
>
> Changes from v1:
> - Due to review comments by Sam Ravnborg, thanks!
> https://lore.kernel.org/dri-devel/[email protected]/
> - Don't preserve newlines with '|' in description
> - Use reset-gpios and backlight from panel-common.yaml
> - Reindent example
> https://lore.kernel.org/dri-devel/[email protected]/
> - Drop unused includes
> - Use dev_* instead of DRM_* for printing
> - Turn off regulators in reverse order from enable
> - Silence errors in mantix_{shutdown,remove}
> - Drop duplicate mipi_dsi_dcs_enter_sleep_mode()
> https://lore.kernel.org/dri-devel/[email protected]/
> - Use dev_err_probe()
> - Add delays when turning off panel as suggested by the data sheet
>
> This series is against next-20200814.
>
> Guido G?nther (3):
> dt-bindings: vendor-prefixes: Add mantix vendor prefix
> dt-bindings: Add Mantix MLAF057WE51-X panel bindings
> drm/panel: Add panel driver for the Mantix MLAF057WE51-X DSI panel
Maxime Ripard backmerged -rc1 to drm-misc-next so I went ahead and applied
this series to drm-misc-next, forgetting you got commit rights. As they are
already pushed out too late for you to do push them - sorry!
Sam
>
> .../display/panel/mantix,mlaf057we51-x.yaml | 70 ++++
> .../devicetree/bindings/vendor-prefixes.yaml | 2 +
> MAINTAINERS | 7 +
> drivers/gpu/drm/panel/Kconfig | 11 +
> drivers/gpu/drm/panel/Makefile | 1 +
> .../gpu/drm/panel/panel-mantix-mlaf057we51.c | 328 ++++++++++++++++++
> 6 files changed, 419 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/panel/mantix,mlaf057we51-x.yaml
> create mode 100644 drivers/gpu/drm/panel/panel-mantix-mlaf057we51.c
>
> --
> 2.26.2
Hi Sam,
On Tue, Aug 18, 2020 at 07:05:56PM +0200, Sam Ravnborg wrote:
> Hi Guido.
>
> On Mon, Aug 17, 2020 at 10:14:33AM +0200, Guido G?nther wrote:
> >
> > The panel uses a Focaltech FT8006p, the touch part is handled by the already
> > existing edt-ft5x06. It can be found in e.g. the Librem 5.
> >
> > Changes from v2:
> > - Due to review comments by Sam Ravnborg, thanks!
> > https://lore.kernel.org/lkml/[email protected]/
> > - Drop unused header
> > - Use newline before comment
> > - Add Reviewed/Acked-by by Sam Ravnborg, thanks!
> > https://lore.kernel.org/lkml/[email protected]/
> > https://lore.kernel.org/lkml/[email protected]/
> > https://lore.kernel.org/lkml/[email protected]/
> >
> > Changes from v1:
> > - Due to review comments by Sam Ravnborg, thanks!
> > https://lore.kernel.org/dri-devel/[email protected]/
> > - Don't preserve newlines with '|' in description
> > - Use reset-gpios and backlight from panel-common.yaml
> > - Reindent example
> > https://lore.kernel.org/dri-devel/[email protected]/
> > - Drop unused includes
> > - Use dev_* instead of DRM_* for printing
> > - Turn off regulators in reverse order from enable
> > - Silence errors in mantix_{shutdown,remove}
> > - Drop duplicate mipi_dsi_dcs_enter_sleep_mode()
> > https://lore.kernel.org/dri-devel/[email protected]/
> > - Use dev_err_probe()
> > - Add delays when turning off panel as suggested by the data sheet
> >
> > This series is against next-20200814.
> >
> > Guido G?nther (3):
> > dt-bindings: vendor-prefixes: Add mantix vendor prefix
> > dt-bindings: Add Mantix MLAF057WE51-X panel bindings
> > drm/panel: Add panel driver for the Mantix MLAF057WE51-X DSI panel
>
> Maxime Ripard backmerged -rc1 to drm-misc-next so I went ahead and applied
> this series to drm-misc-next, forgetting you got commit rights. As they are
> already pushed out too late for you to do push them - sorry!
On the contrary: Thanks a lot for handling this so promptly!
-- Guido