Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1753525Ab3CJXQK (ORCPT ); Sun, 10 Mar 2013 19:16:10 -0400 Received: from mail.active-venture.com ([67.228.131.205]:49626 "EHLO mail.active-venture.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1753419Ab3CJXPL (ORCPT ); Sun, 10 Mar 2013 19:15:11 -0400 X-Virus-Scan: Scanned by ClamAV 0.97.2 (no viruses); Sun, 10 Mar 2013 18:15:06 -0500 X-Originating-IP: 108.223.40.66 From: Guenter Roeck To: linux-watchdog@vger.kernel.org Cc: Wim Van Sebroeck , linux-kernel@vger.kernel.org, Guenter Roeck Subject: [PATCH v2 5/7] watchdog: w83627hf: Auto-detect IO address and supported chips Date: Sun, 10 Mar 2013 16:14:58 -0700 Message-Id: <1362957300-18223-6-git-send-email-linux@roeck-us.net> X-Mailer: git-send-email 1.7.9.7 In-Reply-To: <1362957300-18223-1-git-send-email-linux@roeck-us.net> References: <1362957300-18223-1-git-send-email-linux@roeck-us.net> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 7669 Lines: 292 Instead of requiring the user to provide an IO address per module parameter, auto-detect it as well as supported chips. Signed-off-by: Guenter Roeck --- v2: Merge with patch 6/8 Add support for W83627S, W83627DHG-P, W83667HG, and NCT6779 drivers/watchdog/Kconfig | 15 +++- drivers/watchdog/w83627hf_wdt.c | 182 ++++++++++++++++++++++++++++++++++----- 2 files changed, 173 insertions(+), 24 deletions(-) diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig index dd462af..ef41028 100644 --- a/drivers/watchdog/Kconfig +++ b/drivers/watchdog/Kconfig @@ -854,13 +854,20 @@ config VIA_WDT Most people will say N. config W83627HF_WDT - tristate "W83627HF/W83627DHG Watchdog Timer" + tristate "Watchdog timer for W83627HF/W83627DHG and compatibles" depends on X86 select WATCHDOG_CORE ---help--- - This is the driver for the hardware watchdog on the W83627HF chipset - as used in Advantech PC-9578 and Tyan S2721-533 motherboards - (and likely others). The driver also supports the W83627DHG chip. + This is the driver for the hardware watchdog on the following + Super I/O chips. + W83627DHG/DHG-P/EHF/EHG/F/G/HF/S/SF/THF/UHG/UG + W83637HF + W83667HG/HG-B + W83687THF + NCT6775 + NCT6776 + NCT6779 + This watchdog simply watches your kernel to make sure it doesn't freeze, and if it does, it reboots your computer after a certain amount of time. diff --git a/drivers/watchdog/w83627hf_wdt.c b/drivers/watchdog/w83627hf_wdt.c index 04cf20f..eb368f2 100644 --- a/drivers/watchdog/w83627hf_wdt.c +++ b/drivers/watchdog/w83627hf_wdt.c @@ -44,10 +44,11 @@ #define WATCHDOG_NAME "w83627hf/thf/hg/dhg WDT" #define WATCHDOG_TIMEOUT 60 /* 60 sec default timeout */ -/* You must set this - there is no sane way to probe for this board. */ -static int wdt_io = 0x2E; -module_param(wdt_io, int, 0); -MODULE_PARM_DESC(wdt_io, "w83627hf/thf WDT io port (default 0x2E)"); +static int wdt_io; + +enum chips { w83627hf, w83627s, w83637hf, w83627thf, w83687thf, + w83627ehf, w83627dhg, w83627uhg, w83667hg, w83627dhg_p, w83667hg_b, + nct6775, nct6776, nct6779 }; static int timeout; /* in seconds */ module_param(timeout, int, 0); @@ -66,6 +67,21 @@ MODULE_PARM_DESC(timeout, #define W83627HF_LD_WDT 0x08 +#define W83627HF_ID 0x52 +#define W83627S_ID 0x59 +#define W83637HF_ID 0x70 +#define W83627THF_ID 0x82 +#define W83687THF_ID 0x85 +#define W83627EHF_ID 0x88 +#define W83627DHG_ID 0xa0 +#define W83627UHG_ID 0xa2 +#define W83667HG_ID 0xa5 +#define W83627DHG_P_ID 0xb0 +#define W83667HG_B_ID 0xb3 +#define NCT6775_ID 0xb4 +#define NCT6776_ID 0xc3 +#define NCT6779_ID 0xc5 + static void superio_outb(int reg, int val) { outb(reg, WDT_EFER); @@ -100,10 +116,7 @@ static void superio_exit(void) release_region(wdt_io, 2); } -/* tyan motherboards seem to set F5 to 0x4C ? - * So explicitly init to appropriate value. */ - -static int w83627hf_init(struct watchdog_device *wdog) +static int w83627hf_init(struct watchdog_device *wdog, enum chips chip) { int ret; unsigned char t; @@ -113,20 +126,59 @@ static int w83627hf_init(struct watchdog_device *wdog) return ret; superio_select(W83627HF_LD_WDT); - t = superio_inb(0x20); /* check chip version */ - if (t == 0x82) { /* W83627THF */ - t = (superio_inb(0x2b) & 0xf7); - superio_outb(0x2b, t | 0x04); /* set GPIO3 to WDT0 */ - } else if (t == 0x88 || t == 0xa0) { /* W83627EHF / W83627DHG */ - t = superio_inb(0x2d); - superio_outb(0x2d, t & ~0x01); /* set GPIO5 to WDT0 */ - } /* set CR30 bit 0 to activate GPIO2 */ t = superio_inb(0x30); if (!(t & 0x01)) superio_outb(0x30, t | 0x01); + switch (chip) { + case w83627hf: + case w83627s: + t = superio_inb(0x2B) & ~0x10; + superio_outb(0x2B, t); /* set GPIO24 to WDT0 */ + break; + case w83627thf: + t = (superio_inb(0x2B) & ~0x08) | 0x04; + superio_outb(0x2B, t); /* set GPIO3 to WDT0 */ + break; + case w83627dhg: + case w83627dhg_p: + t = superio_inb(0x2D) & ~0x01; /* PIN77 -> WDT0# */ + superio_outb(0x2D, t); /* set GPIO5 to WDT0 */ + t = superio_inb(0xF5); + t |= 0x02; /* enable the WDTO# output low pulse + * to the KBRST# pin */ + superio_outb(0xF5, t); + break; + case w83637hf: + break; + case w83687thf: + t = superio_inb(0x2C) & ~0x80; /* PIN47 -> WDT0# */ + superio_outb(0x2C, t); + break; + case w83627ehf: + case w83627uhg: + case w83667hg: + case w83667hg_b: + case nct6775: + case nct6776: + case nct6779: + /* + * These chips have a fixed WDTO# output pin (W83627UHG), + * or support more than one WDTO# output pin. + * Don't touch its configuration, and hope the BIOS + * does the right thing. + */ + t = superio_inb(0xF5); + t |= 0x02; /* enable the WDTO# output low pulse + * to the KBRST# pin */ + superio_outb(0xF5, t); + break; + default: + break; + } + t = superio_inb(0xF6); if (t != 0) { pr_info("Watchdog already running. Resetting timeout to %d sec\n", @@ -136,8 +188,6 @@ static int w83627hf_init(struct watchdog_device *wdog) /* set second mode & disable keyboard turning off watchdog */ t = superio_inb(0xF5) & ~0x0C; - /* enable the WDTO# output low pulse to the KBRST# pin */ - t |= 0x02; superio_outb(0xF5, t); /* disable keyboard & mouse turning off watchdog */ @@ -245,17 +295,109 @@ static struct notifier_block wdt_notifier = { .notifier_call = wdt_notify_sys, }; +static int wdt_find(int addr) +{ + u8 val; + int ret; + + ret = superio_enter(); + if (ret) + return ret; + superio_select(W83627HF_LD_WDT); + val = superio_inb(0x20); + switch (val) { + case W83627HF_ID: + ret = w83627hf; + break; + case W83627S_ID: + ret = w83627s; + break; + case W83637HF_ID: + ret = w83637hf; + break; + case W83627THF_ID: + ret = w83627thf; + break; + case W83687THF_ID: + ret = w83687thf; + break; + case W83627EHF_ID: + ret = w83627ehf; + break; + case W83627DHG_ID: + ret = w83627dhg; + break; + case W83627DHG_P_ID: + ret = w83627dhg_p; + break; + case W83627UHG_ID: + ret = w83627uhg; + break; + case W83667HG_ID: + ret = w83667hg; + break; + case W83667HG_B_ID: + ret = w83667hg_b; + break; + case NCT6775_ID: + ret = nct6775; + break; + case NCT6776_ID: + ret = nct6776; + break; + case NCT6779_ID: + ret = nct6779; + break; + case 0xff: + ret = -ENODEV; + break; + default: + ret = -ENODEV; + pr_err("Unsupported chip ID: 0x%02x\n", val); + break; + } + superio_exit(); + return ret; +} + static int __init wdt_init(void) { int ret; bool nowayout = WATCHDOG_NOWAYOUT; + int chip; + const char * const chip_name[] = { + "W83627HF", + "W83627S", + "W83637HF", + "W83627THF", + "W83687THF", + "W83627EHF", + "W83627DHG", + "W83627UHG", + "W83667HG", + "W83667DHG-P", + "W83667HG-B", + "NCT6775", + "NCT6776", + "NCT6779", + }; + + wdt_io = 0x2e; + chip = wdt_find(0x2e); + if (chip < 0) { + wdt_io = 0x4e; + chip = wdt_find(0x4e); + if (chip < 0) + return chip; + } - pr_info("WDT driver for the Winbond(TM) W83627HF/THF/HG/DHG Super I/O chip initialising\n"); + pr_info("WDT driver for %s Super I/O chip initialising\n", + chip_name[chip]); watchdog_init_timeout(&wdt_dev, timeout, NULL); watchdog_set_nowayout(&wdt_dev, nowayout); - ret = w83627hf_init(&wdt_dev); + ret = w83627hf_init(&wdt_dev, chip); if (ret) { pr_err("failed to initialize watchdog (err=%d)\n", ret); return ret; -- 1.7.9.7 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/