Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1753568Ab3DLBb7 (ORCPT ); Thu, 11 Apr 2013 21:31:59 -0400 Received: from e23smtp09.au.ibm.com ([202.81.31.142]:47074 "EHLO e23smtp09.au.ibm.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752409Ab3DLBb4 (ORCPT ); Thu, 11 Apr 2013 21:31:56 -0400 From: Wanpeng Li To: Greg Kroah-Hartman Cc: Dan Magenheimer , Seth Jennings , Konrad Rzeszutek Wilk , Minchan Kim , linux-mm@kvack.org, linux-kernel@vger.kernel.org, Andrew Morton , Bob Liu , Wanpeng Li Subject: [PATCH PART2 v2 7/7] staging: ramster: add how-to for ramster Date: Fri, 12 Apr 2013 09:31:27 +0800 Message-Id: <1365730287-16876-8-git-send-email-liwanp@linux.vnet.ibm.com> X-Mailer: git-send-email 1.7.5.4 In-Reply-To: <1365730287-16876-1-git-send-email-liwanp@linux.vnet.ibm.com> References: <1365730287-16876-1-git-send-email-liwanp@linux.vnet.ibm.com> X-Content-Scanned: Fidelis XPS MAILER x-cbid: 13041201-3568-0000-0000-00000369C4AB Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 11175 Lines: 281 Add how-to for ramster. Acked-by: Dan Magenheimer Singed-off-by: Dan Magenheimer Signed-off-by: Wanpeng Li --- drivers/staging/zcache/ramster/HOWTO.txt | 257 ++++++++++++++++++++++++++++++ 1 file changed, 257 insertions(+) create mode 100644 drivers/staging/zcache/ramster/HOWTO.txt diff --git a/drivers/staging/zcache/ramster/HOWTO.txt b/drivers/staging/zcache/ramster/HOWTO.txt new file mode 100644 index 0000000..a4ee979 --- /dev/null +++ b/drivers/staging/zcache/ramster/HOWTO.txt @@ -0,0 +1,257 @@ +Version: 130309 + Dan Magenheimer + +This is a how-to document for RAMster. It applies to the March 9, 2013 +version of RAMster, re-merged with the new zcache codebase, built and tested +on the 3.9 tree and submitted for the staging tree for 3.9. + +Note that this document was created from notes taken earlier. I would +appreciate any feedback from anyone who follows the process as described +to confirm that it works and to clarify any possible misunderstandings, +or to report problems. + +A. PRELIMINARY + +1) Install two or more Linux systems that are known to work when upgraded + to a recent upstream Linux kernel version (e.g. v3.9). I used Oracle + Linux 6 ("OL6") on two Dell Optiplex 790s. Note that it should be possible + to use ocfs2 as a filesystem on your systems but this hasn't been + tested thoroughly, so if you do use ocfs2 and run into problems, please + report them. Up to eight nodes should work, but not much testing has + been done with more than three nodes. + +On each system: + +2) Configure, build and install then boot Linux (e.g. 3.9), just to ensure it + can be done with an unmodified upstream kernel. Confirm you booted + the upstream kernel with "uname -a". + +3) Install ramster-tools. The src.rpm and an OL6 rpm are available + in this directory. I'm not very good at userspace stuff and + would welcome any help in turning ramster-tools into more + distributable rpms/debs for a wider range of distros. + +B. BUILDING RAMSTER INTO THE KERNEL + +Do the following on each system: + +1) Ensure you have the new codebase for drivers/staging/zcache in your source. + +2) Change your .config to have: + + CONFIG_CLEANCACHE=y + CONFIG_FRONTSWAP=y + CONFIG_STAGING=y + CONFIG_ZCACHE=y + CONFIG_RAMSTER=y + + You may have to reconfigure your kernel multiple times to ensure + all of these are set properly. I use: + + # yes "" | make oldconfig + + and then manually check the .config file to ensure my selections + have "taken". + + Do not bother to build the kernel until you are certain all of + the above config selections will stick for the build. + +3) Build this kernel and "make install" so that you have a new kernel + in /etc/grub.conf + +4) Add "ramster" to the kernel boot line in /etc/grub.conf. + +5) Reboot and check dmesg to ensure there are some messages from ramster + and that "ramster_enabled=1" appears. + + # dmesg | grep ramster + + You should also see a lot of files in: + + # ls /sys/kernel/debug/zcache + # ls /sys/kernel/debug/ramster + + and a few files in: + + # ls /sys/kernel/mm/ramster + + RAMster now will act as a single-system zcache but doesn't yet + know anything about the cluster so can't do anything remotely. + +C. BUILDING THE RAMSTER CLUSTER + +This is the error prone part unless you are a clustering expert. We need +to describe the cluster in /etc/ramster.conf file and the init scripts +that parse it are extremely picky about the syntax. + +1) Create the /etc/ramster.conf file and ensure it is identical + on both systems. There is a good amount of similar documentation + for ocfs2 /etc/cluster.conf that can be googled for this, but I use: + + cluster: + name = ramster + node_count = 2 + node: + name = system1 + cluster = ramster + number = 0 + ip_address = my.ip.ad.r1 + ip_port = 7777 + node: + name = system2 + cluster = ramster + number = 0 + ip_address = my.ip.ad.r2 + ip_port = 7777 + + You must ensure that the "name" field in the file exactly matches + the output of "hostname" on each system. The following assumes + you use "ramster" as the name of your cluster. + +2) Enable the ramster service and configure it: + + # chkconfig --add ramster + # service ramster configure + + Set "load on boot" to "y", cluster to start is "ramster" (or whatever + name you chose in ramster.conf), heartbeat dead threshold as "500", + network idle timeout as "1000000". Leave the others as default. + +4) Reboot. After reboot, try: + + # service ramster status + + You should see "Checking ramster cluster ramster: Online". If you do + not, something is wrong and RAMster will not work. Note that you + should also see that the driver for "configfs" is loaded and mounted, + the driver for ocfs2_dlmfs is not loaded, and some numbers for network + parameters. You will also see "Checking ramster heartbeat: Not active". + That's all OK. + +5) Now you need to start the cluster heartbeat; the cluster is not "up" + until all nodes detect a heartbeat. Normally this is done via + a cluster filesystem, but you don't have one. Some hack-y + code in RAMster can start it for you though if you tell it what + nodes are "up". To enable it for nodes 0 and 1, do: + + # echo 0 > /sys/kernel/mm/ramster/manual_node_up + # echo 1 > /sys/kernel/mm/ramster/manual_node_up + + This must be done on ALL nodes. I usually put these lines + in /etc/rc.local as otherwise I forget. To confirm that + the cluster is now up, on both systems do: + + # dmesg | grep ramster + + You should see "Accepted connection" messages in dmesg after this. + +6) You must tell each node the node to which it should "remotify" pages. + For example if you have a three-node cluster and you want nodes + 1 and 2 to be "clients" and node 0 to be the "memory server", then + on nodes 1 and 2, you do: + + # echo 0 > /sys/kernel/mm/ramster/remote_target_nodenum + + You should see "ramster: node N set as remotification target" + in dmesg. Again, /etc/rc.local is a good place to put this + so you don't forget to do it at each boot. + +7) One more step: By default, the RAMster code does not "remotify" any + pages; this is primarily for testing purposes, but sometimes it is + useful. This may change in the future, but for now, you must: + + # echo 1 > /sys/kernel/mm/ramster/pers_remotify_enable + # echo 1 > /sys/kernel/mm/ramster/eph_remotify_enable + + The first enables remotifying swap (persistent, aka frontswap) pages, + the second enables remotifying of page cache (ephemeral, cleancache) + pages. + + These lines can also be put in /etc/rc.local (AFTER the node_up + lines), or I often just put them at the beginning of my script that + runs a workload. + +8) Most testing has been done with both/all machines booted roughly + simultaneously. Ideally, you should do this too unless you are + trying to break RAMster rather than just use it. ;-) + +D. TESTING RAMSTER + +1) Note that RAMster has no value unless pages get "remotified". For + swap/frontswap/persistent pages, this doesn't happen unless/until + the workload would cause swapping to occur, at which point pages + are put into frontswap/zcache, and the remotification thread starts + working. To get to the point where the system swaps, you either + need a workload for which the working set exceeds the RAM in the + system; or you need to somehow reduce the amount of RAM one of + the system sees. This latter is easy when testing in a VM, but + harder on physical systems. In some cases, "mem=xxxM" on the + kernel command line restricts memory, but for some values of xxx + my kernel fails to boot. I may also try creating a fixed RAMdisk, + doing nothing with it, but ensuring that it eats up a fixed + amount of RAM. +2) To see if RAMster is working, on the remote system, I do: + + # watch -d 'cat /sys/kernel/debug/ramster/foreign_*' + + to monitor the number (and max) ephemeral and persistent pages + that RAMster has sent. If these stay at 0, RAMster is not working + either because the workload isn't creating enough memory pressure + or because "remotifying" isn't working. On the system with the + workload, you can watch lots of useful information also, but beware + that you may be affecting the workload and performance. I use + # watch ./watchme + where the watchme file contains: + + for i in /sys/kernel/debug/zcache/evicted_buddied_pages \ + /sys/kernel/debug/zcache/evicted_raw_pages \ + /sys/kernel/debug/zcache/evicted_unbuddied_pages \ + /sys/kernel/debug/zcache/zbud_curr_raw_pages \ + /sys/kernel/debug/zcache/zbud_curr_zbytes \ + /sys/kernel/debug/zcache/zbud_curr_zpages \ + /sys/kernel/debug/ramster/eph_pages_remoted \ + /sys/kernel/debug/ramster/remote_eph_pages_succ_get \ + /sys/kernel/debug/ramster/remote_pers_pages_succ_get \ + /sys/kernel/debug/frontswap/succ_puts + do + echo $i ": " $(cat $i) + done + And if you have debugfs mounted (as /sys/kernel/debug), you can + add to the watchme script some interesting counters in + /sys/kernel/debug/cleancache/* and /sys/kernel/debug/frontswap/* + +3) In v4, there are known issues in counting certain values. As a result + you may see periodic warnings from the kernel. Almost always you + will see "ramster: bad accounting for XXX". There are also "WARN_ONCE" + messages. If you see kernel warnings with a tombstone, please report + them. They are harmless but reflect bugs that need to be eventually fixed. + +AUTOMATIC SWAP REPATRIATION + +You may notice that while the systems are idle, the foreign persistent +page count on the remote machine slowly decreases. This is because +RAMster implements "frontswap selfshrinking": When possible, swap +pages that have been remotified are slowly repatriated to the local +machine. This is so that local RAM can be used when possible and +so that, in case of remote machine crash, the probability of loss +of data is reduced. + +REBOOTING / POWEROFF + +If a system is shut down while some of its swap pages still reside +on a remote system, the system may lock up partially through the shutdown +sequence. This is because the network is shut down before the +swap mechansim is shut down. To avoid this annoying problem, simply +shut off the swap subsystem before starting the shutdown sequence, e.g.: + + # swapoff -a + # reboot + + +CHANGELOG: +v5-120214->120817: updated for merge into new zcache codebase +v4-120126->v5-120214: updated for V5 +111227->v4-120126: added info on selfshrinking and rebooting +111227->v4-120126: added more info for tracking RAMster stats +111227->v4-120126: CONFIG_PREEMPT_NONE no longer necessary +111227->v4-120126: cleancache now works completely so no need to disable it -- 1.7.10.4 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/