Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id ; Fri, 29 Dec 2000 10:47:39 -0500 Received: (majordomo@vger.kernel.org) by vger.kernel.org id ; Fri, 29 Dec 2000 10:47:29 -0500 Received: from ip-205-254-202-114.netwrx1.com ([205.254.202.114]:16910 "EHLO eagle.netwrx1.com") by vger.kernel.org with ESMTP id ; Fri, 29 Dec 2000 10:47:10 -0500 From: "George R. Kasica" To: linux-kernel@vger.kernel.org, linux-scsi@vger.kernel.org Subject: SCSI Problems since upgrade from 2.2.16 Date: Fri, 29 Dec 2000 09:16:38 -0600 Organization: Netwrx Consulting Inc. Reply-To: georgek@netwrx1.com Message-ID: X-Mailer: Forte Agent 1.8/32.548 MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Sender: linux-kernel-owner@vger.kernel.org X-Mailing-List: linux-kernel@vger.kernel.org Hello: I'm running an HP DAT 4mm Autochanger here and since going to 2.2.17 and 2.2.18 I'm seeing failures when it attempts to unload the tape and load a new one while backing up using BRU PE...utilizing the mt or mtx commands as follows: mt -f $DEV rewoffl 2>&1 >/dev/null OR /usr/local/bin/mtx -f /dev/sg1 eject 2>&1 >/dev/null If I use the MTX command set to "manually" change the tapes all is well....any thoughts on the cause or a fix...I don't think the hardware is broken due to the fact it runs fine "manually" by doing the mtx -f /dev/sg1 next commnand to load the next tape Pertinent info below: Information about installed SCSI devices Attached devices: Host: scsi0 Channel: 00 Id: 01 Lun: 00 Vendor: SEAGATE Model: ST32550N Rev: 0021 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi0 Channel: 00 Id: 03 Lun: 00 Vendor: HP Model: C1553A Rev: NS01 Type: Sequential-Access ANSI SCSI revision: 02 Host: scsi0 Channel: 00 Id: 03 Lun: 01 Vendor: HP Model: C1553A Rev: NS01 Type: Medium Changer ANSI SCSI revision: 02 Bus 0, device 9, function 0: SCSI storage controller: Adaptec AIC-7850 (rev 1). Medium devsel. Fast back-to-back capable. IRQ 10. Master Capable. Latency=32. Min Gnt=4.Max Lat=4. I/O at 0xd000 [0xd001]. Non-prefetchable 32 bit memory at 0xdf000000 [0xdf000000]. SCSI support CONFIG_SCSI = 1 CONFIG_BLK_DEV_SD = 1 CONFIG_CHR_DEV_ST = 1 CONFIG_BLK_DEV_SR = 1 CONFIG_CHR_DEV_SG = 1 CONFIG_SCSI_MULTI_LUN = 1 CONFIG_SCSI_CONSTANTS = 1 CONFIG_SCSI_LOGGING = 1 SCSI low-level drivers CONFIG_SCSI_AIC7XXX = 1 CONFIG_AIC7XXX_CMDS_PER_DEVICE = (8) CONFIG_AIC7XXX_RESET_DELAY = (5) > Len: 20480 > > Dec 23 01:24:37 eagle kernel: [valid=0] Info fld=0x0, EOM Current > st09:00: sense key None > Dec 23 01:24:37 eagle kernel: Additional sense indicates > End-of-partition/medium detected > Dec 23 01:24:37 eagle kernel: st0: Async write error (write) 7fffffff. > Dec 23 01:24:40 eagle kernel: st0: File length 641863680 bytes. > Dec 23 01:24:40 eagle kernel: st0: Async write waits 30037, finished > 1304. > Dec 23 01:24:42 eagle kernel: st0: Error: 28000002, cmd: 10 0 0 0 1 0 > Len: 0 > Dec 23 01:24:42 eagle kernel: [valid=0] Info fld=0x0, FMK EOM Current > st09:00: sense key None > Dec 23 01:24:42 eagle kernel: Additional sense indicates > End-of-partition/medium detected > Dec 23 01:24:42 eagle kernel: st0: Buffer flushed, 1 EOF(s) written ===[George R. Kasica]=== +1 262 513 8503 President +1 206 374 6482 FAX Netwrx Consulting Inc. Waukesha, WI USA http://www.netwrx1.com georgek@netwrx1.com ICQ #12862186 - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/