Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1422710Ab3FUNqX (ORCPT ); Fri, 21 Jun 2013 09:46:23 -0400 Received: from eu1sys200aog121.obsmtp.com ([207.126.144.151]:38204 "EHLO eu1sys200aog121.obsmtp.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1161356Ab3FUNqU (ORCPT ); Fri, 21 Jun 2013 09:46:20 -0400 Message-ID: <51C45816.5010207@st.com> Date: Fri, 21 Jun 2013 14:41:42 +0100 From: Srinivas KANDAGATLA Reply-To: srinivas.kandagatla@st.com Organization: STMicroelectronics User-Agent: Mozilla/5.0 (X11; Linux i686; rv:17.0) Gecko/20130308 Thunderbird/17.0.4 MIME-Version: 1.0 To: Srinivas KANDAGATLA Cc: linux-arm-kernel@lists.infradead.org, Rob Landley , Grant Likely , Rob Herring , Russell King , Stuart Menefy , John Stultz , Thomas Gleixner , Linus Walleij , Greg Kroah-Hartman , Jiri Slaby , linux-doc@vger.kernel.org, linux-kernel@vger.kernel.org, devicetree-discuss@lists.ozlabs.org, kernel@stlinux.com, linux-serial@vger.kernel.org, Mark Brown , Stephen Gallimore , Arnd Bergmann Subject: Re: [PATCH v3 03/10] pinctrl:st: Add pinctrl and pinconf support. References: <1371736996-8770-1-git-send-email-srinivas.kandagatla@st.com> <1371737138-9340-1-git-send-email-srinivas.kandagatla@st.com> In-Reply-To: <1371737138-9340-1-git-send-email-srinivas.kandagatla@st.com> Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 7bit Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 51155 Lines: 1604 Hi Linus W, If its not too late can this patch be considered for 3.11 via pinctrl tree? There is a build dependecy with regmap_field apis pulled by Mark Brown in regmap repository. https://git.kernel.org/cgit/linux/kernel/git/broonie/regmap.git/commit/?h=for-next&id=67252287871113deba96adf7e4df1752f3f08688 Thanks, srini On 20/06/13 15:05, Srinivas KANDAGATLA wrote: > This patch add pinctrl support to ST SoCs. > > About hardware: > ST Set-Top-Box parts have two blocks called PIO and PIO-mux which handle > pin configurations. > > Each multi-function pin is controlled, driven and routed through the PIO > multiplexing block. Each pin supports GPIO functionality (ALT0) and > multiple alternate functions(ALT1 - ALTx) that directly connect the pin > to different hardware blocks. When a pin is in GPIO mode, Output Enable > (OE), Open Drain(OD), and Pull Up (PU) are driven by the related PIO > block. Otherwise the PIO multiplexing block configures these parameters > and retiming the signal. > > About driver: > This pinctrl driver manages both PIO and PIO-mux block using pinctrl, > pinconf, pinmux, gpio subsystems. All the pinctrl related config > information can only come from device trees. > > Signed-off-by: Srinivas Kandagatla > CC: Stephen Gallimore > CC: Stuart Menefy > CC: Arnd Bergmann > CC: Linus Walleij > --- > .../devicetree/bindings/pinctrl/pinctrl-st.txt | 110 ++ > drivers/pinctrl/Kconfig | 6 + > drivers/pinctrl/Makefile | 1 + > drivers/pinctrl/pinctrl-st.c | 1403 ++++++++++++++++++++ > 4 files changed, 1520 insertions(+), 0 deletions(-) > create mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt > create mode 100644 drivers/pinctrl/pinctrl-st.c > > diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt > new file mode 100644 > index 0000000..05bf82a > --- /dev/null > +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt > @@ -0,0 +1,110 @@ > +*ST pin controller. > + > +Each multi-function pin is controlled, driven and routed through the > +PIO multiplexing block. Each pin supports GPIO functionality (ALT0) > +and multiple alternate functions(ALT1 - ALTx) that directly connect > +the pin to different hardware blocks. > + > +When a pin is in GPIO mode, Output Enable (OE), Open Drain(OD), and > +Pull Up (PU) are driven by the related PIO block. > + > +ST pinctrl driver controls PIO multiplexing block and also interacts with > +gpio driver to configure a pin. > + > +Required properties: (PIO multiplexing block) > +- compatible : should be "st,--pinctrl" > + like st,stih415-sbc-pinctrl, st,stih415-front-pinctrl and so on. > +- gpio-controller : Indicates this device is a GPIO controller > +- #gpio-cells : Should be one. The first cell is the pin number. > +- st,retime-pin-mask : Should be mask to specify which pins can be retimed. > + If the property is not present, it is assumed that all the pins in the > + bank are capable of retiming. Retiming is mainly used to improve the > + IO timing margins of external synchronous interfaces. > +- st,bank-name : Should be a name string for this bank as > + specified in datasheet. > +- st,syscfg : Should be a phandle of the syscfg node. > + > +Example: > + pin-controller-sbc { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "st,stih415-sbc-pinctrl"; > + st,syscfg = <&syscfg_sbc>; > + ranges = <0 0xfe610000 0x5000>; > + PIO0: gpio@fe610000 { > + gpio-controller; > + #gpio-cells = <1>; > + reg = <0 0x100>; > + st,bank-name = "PIO0"; > + }; > + ... > + pin-functions nodes follow... > + }; > + > + > +Contents of function subnode node: > +---------------------- > +Required properties for pin configuration node: > +- st,pins : Child node with list of pins with configuration. > + > +Below is the format of how each pin conf should look like. > + > + > + > +Every PIO is represented with 4-7 parameters depending on retime configuration. > +Each parameter is explained as below. > + > +-bank : Should be bank phandle to which this PIO belongs. > +-offset : Offset in the PIO bank. > +-mux : Should be alternate function number associated this pin. > + Use same numbers from datasheet. > +-mode :pin configuration is selected from one of the below values. > + IN > + IN_PU > + OUT > + BIDIR > + BIDIR_PU > + > +-rt_type Retiming Configuration for the pin. > + Possible retime configuration are: > + > + ------- ------------- > + value args > + ------- ------------- > + NICLK > + ICLK_IO > + BYPASS > + DE_IO > + SE_ICLK_IO > + SE_NICLK_IO > + > +- delay is retime delay in pico seconds as mentioned in data sheet. > + > +- rt_clk :clk to be use for retime. > + Possible values are: > + CLK_A > + CLK_B > + CLK_C > + CLK_D > + > +Example of mmcclk pin which is a bi-direction pull pu with retime config > +as non inverted clock retimed with CLK_B and delay of 0 pico seconds: > + > +pin-controller { > + ... > + mmc0 { > + pinctrl_mmc: mmc { > + st,pins { > + mmcclk = <&PIO13 4 ALT4 BIDIR_PU NICLK 0 CLK_B>; > + ... > + }; > + }; > + ... > + }; > +}; > + > +sdhci0:sdhci@fe810000{ > + ... > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_mmc>; > +}; > diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig > index 8f66924..1a147cf 100644 > --- a/drivers/pinctrl/Kconfig > +++ b/drivers/pinctrl/Kconfig > @@ -169,6 +169,12 @@ config PINCTRL_SUNXI > select PINMUX > select GENERIC_PINCONF > > +config PINCTRL_ST > + bool > + depends on OF > + select PINMUX > + select PINCONF > + > config PINCTRL_TEGRA > bool > select PINMUX > diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile > index 9bdaeb8..6fc7844 100644 > --- a/drivers/pinctrl/Makefile > +++ b/drivers/pinctrl/Makefile > @@ -45,6 +45,7 @@ obj-$(CONFIG_PINCTRL_EXYNOS5440) += pinctrl-exynos5440.o > obj-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o > obj-$(CONFIG_PINCTRL_XWAY) += pinctrl-xway.o > obj-$(CONFIG_PINCTRL_LANTIQ) += pinctrl-lantiq.o > +obj-$(CONFIG_PINCTRL_ST) += pinctrl-st.o > > obj-$(CONFIG_PLAT_ORION) += mvebu/ > obj-$(CONFIG_ARCH_SHMOBILE) += sh-pfc/ > diff --git a/drivers/pinctrl/pinctrl-st.c b/drivers/pinctrl/pinctrl-st.c > new file mode 100644 > index 0000000..7effedf > --- /dev/null > +++ b/drivers/pinctrl/pinctrl-st.c > @@ -0,0 +1,1403 @@ > +/* > + * Copyright (C) 2013 STMicroelectronics (R&D) Limited. > + * Authors: > + * Srinivas Kandagatla > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include "core.h" > + > +/* PIO Block registers */ > +/* PIO output */ > +#define REG_PIO_POUT 0x00 > +/* Set bits of POUT */ > +#define REG_PIO_SET_POUT 0x04 > +/* Clear bits of POUT */ > +#define REG_PIO_CLR_POUT 0x08 > +/* PIO input */ > +#define REG_PIO_PIN 0x10 > +/* PIO configuration */ > +#define REG_PIO_PC(n) (0x20 + (n) * 0x10) > +/* Set bits of PC[2:0] */ > +#define REG_PIO_SET_PC(n) (0x24 + (n) * 0x10) > +/* Clear bits of PC[2:0] */ > +#define REG_PIO_CLR_PC(n) (0x28 + (n) * 0x10) > +/* PIO input comparison */ > +#define REG_PIO_PCOMP 0x50 > +/* Set bits of PCOMP */ > +#define REG_PIO_SET_PCOMP 0x54 > +/* Clear bits of PCOMP */ > +#define REG_PIO_CLR_PCOMP 0x58 > +/* PIO input comparison mask */ > +#define REG_PIO_PMASK 0x60 > +/* Set bits of PMASK */ > +#define REG_PIO_SET_PMASK 0x64 > +/* Clear bits of PMASK */ > +#define REG_PIO_CLR_PMASK 0x68 > + > +#define ST_GPIO_DIRECTION_BIDIR 0x1 > +#define ST_GPIO_DIRECTION_OUT 0x2 > +#define ST_GPIO_DIRECTION_IN 0x4 > + > +/** > + * Packed style retime configuration. > + * There are two registers cfg0 and cfg1 in this style for each bank. > + * Each field in this register is 8 bit corresponding to 8 pins in the bank. > + */ > +#define RT_P_CFGS_PER_BANK 2 > +#define RT_P_CFG0_CLK1NOTCLK0_FIELD(reg) REG_FIELD(reg, 0, 7) > +#define RT_P_CFG0_DELAY_0_FIELD(reg) REG_FIELD(reg, 16, 23) > +#define RT_P_CFG0_DELAY_1_FIELD(reg) REG_FIELD(reg, 24, 31) > +#define RT_P_CFG1_INVERTCLK_FIELD(reg) REG_FIELD(reg, 0, 7) > +#define RT_P_CFG1_RETIME_FIELD(reg) REG_FIELD(reg, 8, 15) > +#define RT_P_CFG1_CLKNOTDATA_FIELD(reg) REG_FIELD(reg, 16, 23) > +#define RT_P_CFG1_DOUBLE_EDGE_FIELD(reg) REG_FIELD(reg, 24, 31) > + > +/** > + * Dedicated style retime Configuration register > + * each register is dedicated per pin. > + */ > +#define RT_D_CFGS_PER_BANK 8 > +#define RT_D_CFG_CLK_SHIFT 0 > +#define RT_D_CFG_CLK_MASK (0x3 << 0) > +#define RT_D_CFG_CLKNOTDATA_SHIFT 2 > +#define RT_D_CFG_CLKNOTDATA_MASK BIT(2) > +#define RT_D_CFG_DELAY_SHIFT 3 > +#define RT_D_CFG_DELAY_MASK (0xf << 3) > +#define RT_D_CFG_DELAY_INNOTOUT_SHIFT 7 > +#define RT_D_CFG_DELAY_INNOTOUT_MASK BIT(7) > +#define RT_D_CFG_DOUBLE_EDGE_SHIFT 8 > +#define RT_D_CFG_DOUBLE_EDGE_MASK BIT(8) > +#define RT_D_CFG_INVERTCLK_SHIFT 9 > +#define RT_D_CFG_INVERTCLK_MASK BIT(9) > +#define RT_D_CFG_RETIME_SHIFT 10 > +#define RT_D_CFG_RETIME_MASK BIT(10) > + > +/* > + * Pinconf is represented in an opaque unsigned long variable. > + * Below is the bit allocation details for each possible configuration. > + * All the bit fields can be encapsulated into four variables > + * (direction, retime-type, retime-clk, retime-delay) > + * > + * +----------------+ > + *[31:28]| reserved-3 | > + * +----------------+------------- > + *[27] | oe | | > + * +----------------+ v > + *[26] | pu | [Direction ] > + * +----------------+ ^ > + *[25] | od | | > + * +----------------+------------- > + *[24] | reserved-2 | > + * +----------------+------------- > + *[23] | retime | | > + * +----------------+ | > + *[22] | retime-invclk | | > + * +----------------+ v > + *[21] |retime-clknotdat| [Retime-type ] > + * +----------------+ ^ > + *[20] | retime-de | | > + * +----------------+------------- > + *[19:18]| retime-clk |------>[Retime-Clk ] > + * +----------------+ > + *[17:16]| reserved-1 | > + * +----------------+ > + *[15..0]| retime-delay |------>[Retime Delay] > + * +----------------+ > + */ > + > +#define ST_PINCONF_UNPACK(conf, param)\ > + ((conf >> ST_PINCONF_ ##param ##_SHIFT) \ > + & ST_PINCONF_ ##param ##_MASK) > + > +#define ST_PINCONF_PACK(conf, val, param) (conf |=\ > + ((val & ST_PINCONF_ ##param ##_MASK) << \ > + ST_PINCONF_ ##param ##_SHIFT)) > + > +/* Output enable */ > +#define ST_PINCONF_OE_MASK 0x1 > +#define ST_PINCONF_OE_SHIFT 27 > +#define ST_PINCONF_OE BIT(27) > +#define ST_PINCONF_UNPACK_OE(conf) ST_PINCONF_UNPACK(conf, OE) > +#define ST_PINCONF_PACK_OE(conf) ST_PINCONF_PACK(conf, 1, OE) > + > +/* Pull Up */ > +#define ST_PINCONF_PU_MASK 0x1 > +#define ST_PINCONF_PU_SHIFT 26 > +#define ST_PINCONF_PU BIT(26) > +#define ST_PINCONF_UNPACK_PU(conf) ST_PINCONF_UNPACK(conf, PU) > +#define ST_PINCONF_PACK_PU(conf) ST_PINCONF_PACK(conf, 1, PU) > + > +/* Open Drain */ > +#define ST_PINCONF_OD_MASK 0x1 > +#define ST_PINCONF_OD_SHIFT 25 > +#define ST_PINCONF_OD BIT(25) > +#define ST_PINCONF_UNPACK_OD(conf) ST_PINCONF_UNPACK(conf, OD) > +#define ST_PINCONF_PACK_OD(conf) ST_PINCONF_PACK(conf, 1, OD) > + > +#define ST_PINCONF_RT_MASK 0x1 > +#define ST_PINCONF_RT_SHIFT 23 > +#define ST_PINCONF_RT BIT(23) > +#define ST_PINCONF_UNPACK_RT(conf) ST_PINCONF_UNPACK(conf, RT) > +#define ST_PINCONF_PACK_RT(conf) ST_PINCONF_PACK(conf, 1, RT) > + > +#define ST_PINCONF_RT_INVERTCLK_MASK 0x1 > +#define ST_PINCONF_RT_INVERTCLK_SHIFT 22 > +#define ST_PINCONF_RT_INVERTCLK BIT(22) > +#define ST_PINCONF_UNPACK_RT_INVERTCLK(conf) \ > + ST_PINCONF_UNPACK(conf, RT_INVERTCLK) > +#define ST_PINCONF_PACK_RT_INVERTCLK(conf) \ > + ST_PINCONF_PACK(conf, 1, RT_INVERTCLK) > + > +#define ST_PINCONF_RT_CLKNOTDATA_MASK 0x1 > +#define ST_PINCONF_RT_CLKNOTDATA_SHIFT 21 > +#define ST_PINCONF_RT_CLKNOTDATA BIT(21) > +#define ST_PINCONF_UNPACK_RT_CLKNOTDATA(conf) \ > + ST_PINCONF_UNPACK(conf, RT_CLKNOTDATA) > +#define ST_PINCONF_PACK_RT_CLKNOTDATA(conf) \ > + ST_PINCONF_PACK(conf, 1, RT_CLKNOTDATA) > + > +#define ST_PINCONF_RT_DOUBLE_EDGE_MASK 0x1 > +#define ST_PINCONF_RT_DOUBLE_EDGE_SHIFT 20 > +#define ST_PINCONF_RT_DOUBLE_EDGE BIT(20) > +#define ST_PINCONF_UNPACK_RT_DOUBLE_EDGE(conf) \ > + ST_PINCONF_UNPACK(conf, RT_DOUBLE_EDGE) > +#define ST_PINCONF_PACK_RT_DOUBLE_EDGE(conf) \ > + ST_PINCONF_PACK(conf, 1, RT_DOUBLE_EDGE) > + > +#define ST_PINCONF_RT_CLK_MASK 0x3 > +#define ST_PINCONF_RT_CLK_SHIFT 18 > +#define ST_PINCONF_RT_CLK BIT(18) > +#define ST_PINCONF_UNPACK_RT_CLK(conf) ST_PINCONF_UNPACK(conf, RT_CLK) > +#define ST_PINCONF_PACK_RT_CLK(conf, val) ST_PINCONF_PACK(conf, val, RT_CLK) > + > +/* RETIME_DELAY in Pico Secs */ > +#define ST_PINCONF_RT_DELAY_MASK 0xffff > +#define ST_PINCONF_RT_DELAY_SHIFT 0 > +#define ST_PINCONF_UNPACK_RT_DELAY(conf) ST_PINCONF_UNPACK(conf, RT_DELAY) > +#define ST_PINCONF_PACK_RT_DELAY(conf, val) \ > + ST_PINCONF_PACK(conf, val, RT_DELAY) > + > +#define ST_GPIO_PINS_PER_BANK (8) > +#define OF_GPIO_ARGS_MIN (4) > +#define OF_RT_ARGS_MIN (2) > + > +#define gpio_range_to_bank(chip) \ > + container_of(chip, struct st_gpio_bank, range) > + > +#define gpio_chip_to_bank(chip) \ > + container_of(chip, struct st_gpio_bank, gpio_chip) > + > + > +enum st_retime_style { > + st_retime_style_none, > + st_retime_style_packed, > + st_retime_style_dedicated, > +}; > + > +struct st_retime_dedicated { > + struct regmap_field *rt[ST_GPIO_PINS_PER_BANK]; > +}; > + > +struct st_retime_packed { > + struct regmap_field *clk1notclk0; > + struct regmap_field *delay_0; > + struct regmap_field *delay_1; > + struct regmap_field *invertclk; > + struct regmap_field *retime; > + struct regmap_field *clknotdata; > + struct regmap_field *double_edge; > +}; > + > +struct st_pio_control { > + u32 rt_pin_mask; > + struct regmap_field *alt, *oe, *pu, *od; > + /* retiming */ > + union { > + struct st_retime_packed rt_p; > + struct st_retime_dedicated rt_d; > + } rt; > +}; > + > +struct st_pctl_data { > + enum st_retime_style rt_style; > + unsigned int *input_delays; > + int ninput_delays; > + unsigned int *output_delays; > + int noutput_delays; > + /* register offset information */ > + int alt, oe, pu, od, rt; > +}; > + > +struct st_pinconf { > + int pin; > + const char *name; > + unsigned long config; > + int altfunc; > +}; > + > +struct st_pmx_func { > + const char *name; > + const char **groups; > + unsigned ngroups; > +}; > + > +struct st_pctl_group { > + const char *name; > + unsigned int *pins; > + unsigned npins; > + struct st_pinconf *pin_conf; > +}; > + > +struct st_gpio_bank { > + struct gpio_chip gpio_chip; > + struct pinctrl_gpio_range range; > + void __iomem *base; > + struct st_pio_control pc; > +}; > + > +struct st_pinctrl { > + struct device *dev; > + struct pinctrl_dev *pctl; > + struct st_gpio_bank *banks; > + int nbanks; > + struct st_pmx_func *functions; > + int nfunctions; > + struct st_pctl_group *groups; > + int ngroups; > + struct regmap *regmap; > + const struct st_pctl_data *data; > +}; > + > +/* SOC specific data */ > +/* STiH415 data */ > +unsigned int stih415_input_delays[] = {0, 500, 1000, 1500}; > +unsigned int stih415_output_delays[] = {0, 1000, 2000, 3000}; > + > +#define STIH415_PCTRL_COMMON_DATA \ > + .rt_style = st_retime_style_packed, \ > + .input_delays = stih415_input_delays, \ > + .ninput_delays = 4, \ > + .output_delays = stih415_output_delays, \ > + .noutput_delays = 4 > + > +static const struct st_pctl_data stih415_sbc_data = { > + STIH415_PCTRL_COMMON_DATA, > + .alt = 0, .oe = 5, .pu = 7, .od = 9, .rt = 16, > +}; > + > +static const struct st_pctl_data stih415_front_data = { > + STIH415_PCTRL_COMMON_DATA, > + .alt = 0, .oe = 8, .pu = 10, .od = 12, .rt = 16, > +}; > + > +static const struct st_pctl_data stih415_rear_data = { > + STIH415_PCTRL_COMMON_DATA, > + .alt = 0, .oe = 6, .pu = 8, .od = 10, .rt = 38, > +}; > + > +static const struct st_pctl_data stih415_left_data = { > + STIH415_PCTRL_COMMON_DATA, > + .alt = 0, .oe = 3, .pu = 4, .od = 5, .rt = 6, > +}; > + > +static const struct st_pctl_data stih415_right_data = { > + STIH415_PCTRL_COMMON_DATA, > + .alt = 0, .oe = 5, .pu = 7, .od = 9, .rt = 11, > +}; > + > +/* STiH416 data */ > +unsigned int stih416_delays[] = {0, 300, 500, 750, 1000, 1250, 1500, > + 1750, 2000, 2250, 2500, 2750, 3000, 3250 }; > + > +static const struct st_pctl_data stih416_data = { > + .rt_style = st_retime_style_dedicated, > + .input_delays = stih416_delays, > + .ninput_delays = 14, > + .output_delays = stih416_delays, > + .noutput_delays = 14, > + .alt = 0, .oe = 40, .pu = 50, .od = 60, .rt = 100, > +}; > + > +/* Low level functions.. */ > +static inline int st_gpio_bank(int gpio) > +{ > + return gpio/ST_GPIO_PINS_PER_BANK; > +} > + > +static inline int st_gpio_pin(int gpio) > +{ > + return gpio%ST_GPIO_PINS_PER_BANK; > +} > + > +static void st_pinconf_set_config(struct st_pio_control *pc, > + int pin, unsigned long config) > +{ > + struct regmap_field *output_enable = pc->oe; > + struct regmap_field *pull_up = pc->pu; > + struct regmap_field *open_drain = pc->od; > + unsigned int oe_value, pu_value, od_value; > + unsigned long mask = BIT(pin); > + > + regmap_field_read(output_enable, &oe_value); > + regmap_field_read(pull_up, &pu_value); > + regmap_field_read(open_drain, &od_value); > + > + /* Clear old values */ > + oe_value &= ~mask; > + pu_value &= ~mask; > + od_value &= ~mask; > + > + if (config & ST_PINCONF_OE) > + oe_value |= mask; > + if (config & ST_PINCONF_PU) > + pu_value |= mask; > + if (config & ST_PINCONF_OD) > + od_value |= mask; > + > + regmap_field_write(output_enable, oe_value); > + regmap_field_write(pull_up, pu_value); > + regmap_field_write(open_drain, od_value); > +} > + > +static void st_pctl_set_function(struct st_pio_control *pc, > + int pin_id, int function) > +{ > + struct regmap_field *alt = pc->alt; > + unsigned int val; > + int pin = st_gpio_pin(pin_id); > + int offset = pin * 4; > + > + regmap_field_read(alt, &val); > + val &= ~(0xf << offset); > + val |= function << offset; > + regmap_field_write(alt, val); > +} > + > +static unsigned long st_pinconf_delay_to_bit(unsigned int delay, > + const struct st_pctl_data *data, unsigned long config) > +{ > + unsigned int *delay_times; > + int num_delay_times, i, closest_index = -1; > + unsigned int closest_divergence = UINT_MAX; > + > + if (ST_PINCONF_UNPACK_OE(config)) { > + delay_times = data->output_delays; > + num_delay_times = data->noutput_delays; > + } else { > + delay_times = data->input_delays; > + num_delay_times = data->ninput_delays; > + } > + > + for (i = 0; i < num_delay_times; i++) { > + unsigned int divergence = abs(delay - delay_times[i]); > + > + if (divergence == 0) > + return i; > + > + if (divergence < closest_divergence) { > + closest_divergence = divergence; > + closest_index = i; > + } > + } > + > + pr_warn("Attempt to set delay %d, closest available %d\n", > + delay, delay_times[closest_index]); > + > + return closest_index; > +} > + > +static unsigned long st_pinconf_bit_to_delay(unsigned int index, > + const struct st_pctl_data *data, unsigned long output) > +{ > + unsigned int *delay_times; > + int num_delay_times; > + > + if (output) { > + delay_times = data->output_delays; > + num_delay_times = data->noutput_delays; > + } else { > + delay_times = data->input_delays; > + num_delay_times = data->ninput_delays; > + } > + > + if (index < num_delay_times) { > + return delay_times[index]; > + } else { > + pr_warn("Delay not found in/out delay list\n"); > + return 0; > + } > +} > + > +static void st_regmap_field_bit_set_clear_pin(struct regmap_field *field, > + int enable, int pin) > +{ > + unsigned int val = 0; > + > + regmap_field_read(field, &val); > + if (enable) > + val |= BIT(pin); > + else > + val &= ~BIT(pin); > + regmap_field_write(field, val); > +} > + > +static void st_pinconf_set_retime_packed(struct st_pinctrl *info, > + struct st_pio_control *pc, unsigned long config, int pin) > +{ > + const struct st_pctl_data *data = info->data; > + struct st_retime_packed *rt_p = &pc->rt.rt_p; > + unsigned int delay; > + > + st_regmap_field_bit_set_clear_pin(rt_p->clk1notclk0, > + ST_PINCONF_UNPACK_RT_CLK(config), pin); > + > + st_regmap_field_bit_set_clear_pin(rt_p->clknotdata, > + ST_PINCONF_UNPACK_RT_CLKNOTDATA(config), pin); > + > + st_regmap_field_bit_set_clear_pin(rt_p->double_edge, > + ST_PINCONF_UNPACK_RT_DOUBLE_EDGE(config), pin); > + > + st_regmap_field_bit_set_clear_pin(rt_p->invertclk, > + ST_PINCONF_UNPACK_RT_INVERTCLK(config), pin); > + > + st_regmap_field_bit_set_clear_pin(rt_p->retime, > + ST_PINCONF_UNPACK_RT(config), pin); > + > + delay = st_pinconf_delay_to_bit(ST_PINCONF_UNPACK_RT_DELAY(config), > + data, config); > + /* 2 bit delay, lsb */ > + st_regmap_field_bit_set_clear_pin(rt_p->delay_0, delay & 0x1, pin); > + /* 2 bit delay, msb */ > + st_regmap_field_bit_set_clear_pin(rt_p->delay_1, delay & 0x2, pin); > + > +} > + > +static void st_pinconf_set_retime_dedicated(struct st_pinctrl *info, > + struct st_pio_control *pc, unsigned long config, int pin) > +{ > + int input = ST_PINCONF_UNPACK_OE(config) ? 0 : 1; > + int clk = ST_PINCONF_UNPACK_RT_CLK(config); > + int clknotdata = ST_PINCONF_UNPACK_RT_CLKNOTDATA(config); > + int double_edge = ST_PINCONF_UNPACK_RT_DOUBLE_EDGE(config); > + int invertclk = ST_PINCONF_UNPACK_RT_INVERTCLK(config); > + int retime = ST_PINCONF_UNPACK_RT(config); > + > + unsigned long delay = st_pinconf_delay_to_bit( > + ST_PINCONF_UNPACK_RT_DELAY(config), > + info->data, config); > + struct st_retime_dedicated *rt_d = &pc->rt.rt_d; > + > + unsigned long retime_config = > + ((clk) << RT_D_CFG_CLK_SHIFT) | > + ((delay) << RT_D_CFG_DELAY_SHIFT) | > + ((input) << RT_D_CFG_DELAY_INNOTOUT_SHIFT) | > + ((retime) << RT_D_CFG_RETIME_SHIFT) | > + ((clknotdata) << RT_D_CFG_CLKNOTDATA_SHIFT) | > + ((invertclk) << RT_D_CFG_INVERTCLK_SHIFT) | > + ((double_edge) << RT_D_CFG_DOUBLE_EDGE_SHIFT); > + > + regmap_field_write(rt_d->rt[pin], retime_config); > +} > + > +static void st_pinconf_get_direction(struct st_pio_control *pc, > + int pin, unsigned long *config) > +{ > + unsigned int oe_value, pu_value, od_value; > + > + regmap_field_read(pc->oe, &oe_value); > + regmap_field_read(pc->pu, &pu_value); > + regmap_field_read(pc->od, &od_value); > + > + if (oe_value & BIT(pin)) > + ST_PINCONF_PACK_OE(*config); > + if (pu_value & BIT(pin)) > + ST_PINCONF_PACK_PU(*config); > + if (od_value & BIT(pin)) > + ST_PINCONF_PACK_OD(*config); > + > +} > + > +static int st_pinconf_get_retime_packed(struct st_pinctrl *info, > + struct st_pio_control *pc, int pin, unsigned long *config) > +{ > + const struct st_pctl_data *data = info->data; > + struct st_retime_packed *rt_p = &pc->rt.rt_p; > + unsigned int delay_bits, delay, delay0, delay1, val; > + int output = ST_PINCONF_UNPACK_OE(*config); > + > + if (!regmap_field_read(rt_p->retime, &val) && (val & BIT(pin))) > + ST_PINCONF_PACK_RT(*config); > + > + if (!regmap_field_read(rt_p->clk1notclk0, &val) && (val & BIT(pin))) > + ST_PINCONF_PACK_RT_CLK(*config, 1); > + > + if (!regmap_field_read(rt_p->clknotdata, &val) && (val & BIT(pin))) > + ST_PINCONF_PACK_RT_CLKNOTDATA(*config); > + > + if (!regmap_field_read(rt_p->double_edge, &val) && (val & BIT(pin))) > + ST_PINCONF_PACK_RT_DOUBLE_EDGE(*config); > + > + if (!regmap_field_read(rt_p->invertclk, &val) && (val & BIT(pin))) > + ST_PINCONF_PACK_RT_INVERTCLK(*config); > + > + regmap_field_read(rt_p->delay_0, &delay0); > + regmap_field_read(rt_p->delay_1, &delay1); > + delay_bits = (((delay1 & BIT(pin)) ? 1 : 0) << 1) | > + (((delay0 & BIT(pin)) ? 1 : 0)); > + delay = st_pinconf_bit_to_delay(delay_bits, data, output); > + ST_PINCONF_PACK_RT_DELAY(*config, delay); > + > + return 0; > +} > + > +static int st_pinconf_get_retime_dedicated(struct st_pinctrl *info, > + struct st_pio_control *pc, int pin, unsigned long *config) > +{ > + unsigned int value; > + unsigned long delay_bits, delay, rt_clk; > + int output = ST_PINCONF_UNPACK_OE(*config); > + struct st_retime_dedicated *rt_d = &pc->rt.rt_d; > + > + regmap_field_read(rt_d->rt[pin], &value); > + > + rt_clk = (value & RT_D_CFG_CLK_MASK) >> RT_D_CFG_CLK_SHIFT; > + ST_PINCONF_PACK_RT_CLK(*config, rt_clk); > + > + delay_bits = (value & RT_D_CFG_DELAY_MASK) >> RT_D_CFG_DELAY_SHIFT; > + delay = st_pinconf_bit_to_delay(delay_bits, info->data, output); > + ST_PINCONF_PACK_RT_DELAY(*config, delay); > + > + if (value & RT_D_CFG_CLKNOTDATA_MASK) > + ST_PINCONF_PACK_RT_CLKNOTDATA(*config); > + > + if (value & RT_D_CFG_DOUBLE_EDGE_MASK) > + ST_PINCONF_PACK_RT_DOUBLE_EDGE(*config); > + > + if (value & RT_D_CFG_INVERTCLK_MASK) > + ST_PINCONF_PACK_RT_INVERTCLK(*config); > + > + if (value & RT_D_CFG_RETIME_MASK) > + ST_PINCONF_PACK_RT(*config); > + > + return 0; > +} > + > +/* GPIO related functions */ > + > +static inline void __st_gpio_set(struct st_gpio_bank *bank, > + unsigned offset, int value) > +{ > + if (value) > + writel(BIT(offset), bank->base + REG_PIO_SET_POUT); > + else > + writel(BIT(offset), bank->base + REG_PIO_CLR_POUT); > +} > + > +static void st_gpio_direction(struct st_gpio_bank *bank, > + unsigned int gpio, unsigned int direction) > +{ > + int offset = st_gpio_pin(gpio); > + int i = 0; > + /** > + * There are three configuration registers (PIOn_PC0, PIOn_PC1 > + * and PIOn_PC2) for each port. These are used to configure the > + * PIO port pins. Each pin can be configured as an input, output, > + * bidirectional, or alternative function pin. Three bits, one bit > + * from each of the three registers, configure the corresponding bit of > + * the port. Valid bit settings is: > + * > + * PC2 PC1 PC0 Direction. > + * 0 0 0 [Input Weak pull-up] > + * 0 0 or 1 1 [Bidirection] > + * 0 1 0 [Output] > + * 1 0 0 [Input] > + * > + * PIOn_SET_PC and PIOn_CLR_PC registers are used to set and clear bits > + * individually. > + */ > + for (i = 0; i <= 2; i++) { > + if (direction & BIT(i)) > + writel(BIT(offset), bank->base + REG_PIO_SET_PC(i)); > + else > + writel(BIT(offset), bank->base + REG_PIO_CLR_PC(i)); > + } > +} > + > +static int st_gpio_request(struct gpio_chip *chip, unsigned offset) > +{ > + return pinctrl_request_gpio(chip->base + offset); > +} > + > +static void st_gpio_free(struct gpio_chip *chip, unsigned offset) > +{ > + pinctrl_free_gpio(chip->base + offset); > +} > + > +static int st_gpio_get(struct gpio_chip *chip, unsigned offset) > +{ > + struct st_gpio_bank *bank = gpio_chip_to_bank(chip); > + > + return !!(readl(bank->base + REG_PIO_PIN) & BIT(offset)); > +} > + > +static void st_gpio_set(struct gpio_chip *chip, unsigned offset, int value) > +{ > + struct st_gpio_bank *bank = gpio_chip_to_bank(chip); > + __st_gpio_set(bank, offset, value); > +} > + > +static int st_gpio_direction_input(struct gpio_chip *chip, unsigned offset) > +{ > + pinctrl_gpio_direction_input(chip->base + offset); > + > + return 0; > +} > + > +static int st_gpio_direction_output(struct gpio_chip *chip, > + unsigned offset, int value) > +{ > + struct st_gpio_bank *bank = gpio_chip_to_bank(chip); > + > + __st_gpio_set(bank, offset, value); > + pinctrl_gpio_direction_output(chip->base + offset); > + > + return 0; > +} > + > +static int st_gpio_xlate(struct gpio_chip *gc, > + const struct of_phandle_args *gpiospec, u32 *flags) > +{ > + if (WARN_ON(gc->of_gpio_n_cells < 1)) > + return -EINVAL; > + > + if (WARN_ON(gpiospec->args_count < gc->of_gpio_n_cells)) > + return -EINVAL; > + > + if (gpiospec->args[0] > gc->ngpio) > + return -EINVAL; > + > + return gpiospec->args[0]; > +} > + > +/* Pinctrl Groups */ > +static int st_pctl_get_groups_count(struct pinctrl_dev *pctldev) > +{ > + struct st_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); > + > + return info->ngroups; > +} > + > +static const char *st_pctl_get_group_name(struct pinctrl_dev *pctldev, > + unsigned selector) > +{ > + struct st_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); > + > + return info->groups[selector].name; > +} > + > +static int st_pctl_get_group_pins(struct pinctrl_dev *pctldev, > + unsigned selector, const unsigned **pins, unsigned *npins) > +{ > + struct st_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); > + > + if (selector >= info->ngroups) > + return -EINVAL; > + > + *pins = info->groups[selector].pins; > + *npins = info->groups[selector].npins; > + > + return 0; > +} > + > +static const inline struct st_pctl_group *st_pctl_find_group_by_name( > + const struct st_pinctrl *info, const char *name) > +{ > + int i; > + > + for (i = 0; i < info->ngroups; i++) { > + if (!strcmp(info->groups[i].name, name)) > + return &info->groups[i]; > + } > + > + return NULL; > +} > + > +static int st_pctl_dt_node_to_map(struct pinctrl_dev *pctldev, > + struct device_node *np, struct pinctrl_map **map, unsigned *num_maps) > +{ > + struct st_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); > + const struct st_pctl_group *grp; > + struct pinctrl_map *new_map; > + struct device_node *parent; > + int map_num, i; > + > + grp = st_pctl_find_group_by_name(info, np->name); > + if (!grp) { > + dev_err(info->dev, "unable to find group for node %s\n", > + np->name); > + return -EINVAL; > + } > + > + map_num = grp->npins + 1; > + new_map = devm_kzalloc(pctldev->dev, > + sizeof(*new_map) * map_num, GFP_KERNEL); > + if (!new_map) > + return -ENOMEM; > + > + parent = of_get_parent(np); > + if (!parent) { > + devm_kfree(pctldev->dev, new_map); > + return -EINVAL; > + } > + > + *map = new_map; > + *num_maps = map_num; > + new_map[0].type = PIN_MAP_TYPE_MUX_GROUP; > + new_map[0].data.mux.function = parent->name; > + new_map[0].data.mux.group = np->name; > + of_node_put(parent); > + > + /* create config map per pin */ > + new_map++; > + for (i = 0; i < grp->npins; i++) { > + new_map[i].type = PIN_MAP_TYPE_CONFIGS_PIN; > + new_map[i].data.configs.group_or_pin = > + pin_get_name(pctldev, grp->pins[i]); > + new_map[i].data.configs.configs = &grp->pin_conf[i].config; > + new_map[i].data.configs.num_configs = 1; > + } > + dev_info(pctldev->dev, "maps: function %s group %s num %d\n", > + (*map)->data.mux.function, grp->name, map_num); > + > + return 0; > +} > + > +static void st_pctl_dt_free_map(struct pinctrl_dev *pctldev, > + struct pinctrl_map *map, unsigned num_maps) > +{ > +} > + > +static struct pinctrl_ops st_pctlops = { > + .get_groups_count = st_pctl_get_groups_count, > + .get_group_pins = st_pctl_get_group_pins, > + .get_group_name = st_pctl_get_group_name, > + .dt_node_to_map = st_pctl_dt_node_to_map, > + .dt_free_map = st_pctl_dt_free_map, > +}; > + > +/* Pinmux */ > +static int st_pmx_get_funcs_count(struct pinctrl_dev *pctldev) > +{ > + struct st_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); > + > + return info->nfunctions; > +} > + > +const char *st_pmx_get_fname(struct pinctrl_dev *pctldev, > + unsigned selector) > +{ > + struct st_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); > + > + return info->functions[selector].name; > +} > + > +static int st_pmx_get_groups(struct pinctrl_dev *pctldev, > + unsigned selector, const char * const **grps, unsigned * const ngrps) > +{ > + struct st_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); > + *grps = info->functions[selector].groups; > + *ngrps = info->functions[selector].ngroups; > + > + return 0; > +} > + > +static struct st_pio_control *st_get_pio_control( > + struct pinctrl_dev *pctldev, int pin) > +{ > + struct pinctrl_gpio_range *range = > + pinctrl_find_gpio_range_from_pin(pctldev, pin); > + struct st_gpio_bank *bank = gpio_range_to_bank(range); > + > + return &bank->pc; > +} > + > +static int st_pmx_enable(struct pinctrl_dev *pctldev, unsigned fselector, > + unsigned group) > +{ > + struct st_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); > + struct st_pinconf *conf = info->groups[group].pin_conf; > + struct st_pio_control *pc; > + int i; > + > + for (i = 0; i < info->groups[group].npins; i++) { > + pc = st_get_pio_control(pctldev, conf[i].pin); > + st_pctl_set_function(pc, conf[i].pin, conf[i].altfunc); > + } > + > + return 0; > +} > + > +static void st_pmx_disable(struct pinctrl_dev *pctldev, unsigned selector, > + unsigned group) > +{ > +} > + > +static int st_pmx_set_gpio_direction(struct pinctrl_dev *pctldev, > + struct pinctrl_gpio_range *range, unsigned gpio, > + bool input) > +{ > + struct st_gpio_bank *bank = gpio_range_to_bank(range); > + /* > + * When a PIO bank is used in its primary function mode (altfunc = 0) > + * Output Enable (OE), Open Drain(OD), and Pull Up (PU) > + * for the primary PIO functions are driven by the related PIO block > + */ > + st_pctl_set_function(&bank->pc, gpio, 0); > + st_gpio_direction(bank, gpio, input ? > + ST_GPIO_DIRECTION_IN : ST_GPIO_DIRECTION_OUT); > + > + return 0; > +} > + > +static struct pinmux_ops st_pmxops = { > + .get_functions_count = st_pmx_get_funcs_count, > + .get_function_name = st_pmx_get_fname, > + .get_function_groups = st_pmx_get_groups, > + .enable = st_pmx_enable, > + .disable = st_pmx_disable, > + .gpio_set_direction = st_pmx_set_gpio_direction, > +}; > + > +/* Pinconf */ > +static void st_pinconf_get_retime(struct st_pinctrl *info, > + struct st_pio_control *pc, int pin, unsigned long *config) > +{ > + if (info->data->rt_style == st_retime_style_packed) > + st_pinconf_get_retime_packed(info, pc, pin, config); > + else if (info->data->rt_style == st_retime_style_dedicated) > + if ((BIT(pin) & pc->rt_pin_mask)) > + st_pinconf_get_retime_dedicated(info, pc, > + pin, config); > +} > + > +static void st_pinconf_set_retime(struct st_pinctrl *info, > + struct st_pio_control *pc, int pin, unsigned long config) > +{ > + if (info->data->rt_style == st_retime_style_packed) > + st_pinconf_set_retime_packed(info, pc, config, pin); > + else if (info->data->rt_style == st_retime_style_dedicated) > + if ((BIT(pin) & pc->rt_pin_mask)) > + st_pinconf_set_retime_dedicated(info, pc, > + config, pin); > +} > + > +static int st_pinconf_set(struct pinctrl_dev *pctldev, > + unsigned pin_id, unsigned long config) > +{ > + int pin = st_gpio_pin(pin_id); > + struct st_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); > + struct st_pio_control *pc = st_get_pio_control(pctldev, pin_id); > + > + st_pinconf_set_config(pc, pin, config); > + st_pinconf_set_retime(info, pc, pin, config); > + > + return 0; > +} > + > +static int st_pinconf_get(struct pinctrl_dev *pctldev, > + unsigned pin_id, unsigned long *config) > +{ > + int pin = st_gpio_pin(pin_id); > + struct st_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); > + struct st_pio_control *pc = st_get_pio_control(pctldev, pin_id); > + > + *config = 0; > + st_pinconf_get_direction(pc, pin, config); > + st_pinconf_get_retime(info, pc, pin, config); > + > + return 0; > +} > + > +static void st_pinconf_dbg_show(struct pinctrl_dev *pctldev, > + struct seq_file *s, unsigned pin_id) > +{ > + unsigned long config; > + st_pinconf_get(pctldev, pin_id, &config); > + > + seq_printf(s, "[OE:%ld,PU:%ld,OD:%ld]\n" > + "\t\t[retime:%ld,invclk:%ld,clknotdat:%ld," > + "de:%ld,rt-clk:%ld,rt-delay:%ld]", > + ST_PINCONF_UNPACK_OE(config), > + ST_PINCONF_UNPACK_PU(config), > + ST_PINCONF_UNPACK_OD(config), > + ST_PINCONF_UNPACK_RT(config), > + ST_PINCONF_UNPACK_RT_INVERTCLK(config), > + ST_PINCONF_UNPACK_RT_CLKNOTDATA(config), > + ST_PINCONF_UNPACK_RT_DOUBLE_EDGE(config), > + ST_PINCONF_UNPACK_RT_CLK(config), > + ST_PINCONF_UNPACK_RT_DELAY(config)); > +} > + > +static struct pinconf_ops st_confops = { > + .pin_config_get = st_pinconf_get, > + .pin_config_set = st_pinconf_set, > + .pin_config_dbg_show = st_pinconf_dbg_show, > +}; > + > +static void st_pctl_dt_child_count(struct st_pinctrl *info, > + struct device_node *np) > +{ > + struct device_node *child; > + for_each_child_of_node(np, child) { > + if (of_property_read_bool(child, "gpio-controller")) { > + info->nbanks++; > + } else { > + info->nfunctions++; > + info->ngroups += of_get_child_count(child); > + } > + } > +} > + > +static int st_pctl_dt_setup_retime_packed(struct st_pinctrl *info, > + int bank, struct st_pio_control *pc) > +{ > + struct device *dev = info->dev; > + struct regmap *rm = info->regmap; > + const struct st_pctl_data *data = info->data; > + /* 2 registers per bank */ > + int reg = (data->rt + bank * RT_P_CFGS_PER_BANK) * 4; > + struct st_retime_packed *rt_p = &pc->rt.rt_p; > + /* cfg0 */ > + struct reg_field clk1notclk0 = RT_P_CFG0_CLK1NOTCLK0_FIELD(reg); > + struct reg_field delay_0 = RT_P_CFG0_DELAY_0_FIELD(reg); > + struct reg_field delay_1 = RT_P_CFG0_DELAY_1_FIELD(reg); > + /* cfg1 */ > + struct reg_field invertclk = RT_P_CFG1_INVERTCLK_FIELD(reg + 4); > + struct reg_field retime = RT_P_CFG1_RETIME_FIELD(reg + 4); > + struct reg_field clknotdata = RT_P_CFG1_CLKNOTDATA_FIELD(reg + 4); > + struct reg_field double_edge = RT_P_CFG1_DOUBLE_EDGE_FIELD(reg + 4); > + > + rt_p->clk1notclk0 = devm_regmap_field_alloc(dev, rm, clk1notclk0); > + rt_p->delay_0 = devm_regmap_field_alloc(dev, rm, delay_0); > + rt_p->delay_1 = devm_regmap_field_alloc(dev, rm, delay_1); > + rt_p->invertclk = devm_regmap_field_alloc(dev, rm, invertclk); > + rt_p->retime = devm_regmap_field_alloc(dev, rm, retime); > + rt_p->clknotdata = devm_regmap_field_alloc(dev, rm, clknotdata); > + rt_p->double_edge = devm_regmap_field_alloc(dev, rm, double_edge); > + > + if (IS_ERR(rt_p->clk1notclk0) || IS_ERR(rt_p->delay_0) || > + IS_ERR(rt_p->delay_1) || IS_ERR(rt_p->invertclk) || > + IS_ERR(rt_p->retime) || IS_ERR(rt_p->clknotdata) || > + IS_ERR(rt_p->double_edge)) > + return -EINVAL; > + > + return 0; > +} > + > +static int st_pctl_dt_setup_retime_dedicated(struct st_pinctrl *info, > + int bank, struct st_pio_control *pc) > +{ > + struct device *dev = info->dev; > + struct regmap *rm = info->regmap; > + const struct st_pctl_data *data = info->data; > + /* 8 registers per bank */ > + int reg_offset = (data->rt + bank * RT_D_CFGS_PER_BANK) * 4; > + struct st_retime_dedicated *rt_d = &pc->rt.rt_d; > + unsigned int j; > + u32 pin_mask = pc->rt_pin_mask; > + > + for (j = 0; j < RT_D_CFGS_PER_BANK; j++) { > + if (BIT(j) & pin_mask) { > + struct reg_field reg = REG_FIELD(reg_offset, 0, 31); > + rt_d->rt[j] = devm_regmap_field_alloc(dev, rm, reg); > + if (IS_ERR(rt_d->rt[j])) > + return -EINVAL; > + reg_offset += 4; > + } > + } > + return 0; > +} > + > +static int st_pctl_dt_setup_retime(struct st_pinctrl *info, > + int bank, struct st_pio_control *pc) > +{ > + const struct st_pctl_data *data = info->data; > + if (data->rt_style == st_retime_style_packed) > + return st_pctl_dt_setup_retime_packed(info, bank, pc); > + else if (data->rt_style == st_retime_style_dedicated) > + return st_pctl_dt_setup_retime_dedicated(info, bank, pc); > + > + return -EINVAL; > +} > + > +static int st_parse_syscfgs(struct st_pinctrl *info, > + int bank, struct device_node *np) > +{ > + const struct st_pctl_data *data = info->data; > + /** > + * For a given shared register like OE/PU/OD, there are 8 bits per bank > + * 0:7 belongs to bank0, 8:15 belongs to bank1 ... > + * So each register is shared across 4 banks. > + */ > + int lsb = (bank%4) * ST_GPIO_PINS_PER_BANK; > + int msb = lsb + ST_GPIO_PINS_PER_BANK - 1; > + struct reg_field alt_reg = REG_FIELD((data->alt + bank) * 4, 0, 31); > + struct reg_field oe_reg = REG_FIELD((data->oe + bank/4) * 4, lsb, msb); > + struct reg_field pu_reg = REG_FIELD((data->pu + bank/4) * 4, lsb, msb); > + struct reg_field od_reg = REG_FIELD((data->od + bank/4) * 4, lsb, msb); > + struct st_pio_control *pc = &info->banks[bank].pc; > + struct device *dev = info->dev; > + struct regmap *regmap = info->regmap; > + > + pc->alt = devm_regmap_field_alloc(dev, regmap, alt_reg); > + pc->oe = devm_regmap_field_alloc(dev, regmap, oe_reg); > + pc->pu = devm_regmap_field_alloc(dev, regmap, pu_reg); > + pc->od = devm_regmap_field_alloc(dev, regmap, od_reg); > + > + if (IS_ERR(pc->alt) || IS_ERR(pc->oe) || > + IS_ERR(pc->pu) || IS_ERR(pc->od)) > + return -EINVAL; > + > + /* retime avaiable for all pins by default */ > + pc->rt_pin_mask = 0xff; > + of_property_read_u32(np, "st,retime-pin-mask", &pc->rt_pin_mask); > + st_pctl_dt_setup_retime(info, bank, pc); > + > + return 0; > +} > + > +/* > + * Each pin is represented in of the below forms. > + * > + */ > +static int st_pctl_dt_parse_groups(struct device_node *np, > + struct st_pctl_group *grp, struct st_pinctrl *info, int idx) > +{ > + /* bank pad direction val altfunction */ > + const __be32 *list; > + struct property *pp; > + struct st_pinconf *conf; > + phandle phandle; > + struct device_node *pins; > + u32 pin; > + int i = 0, npins = 0, nr_props; > + > + pins = of_get_child_by_name(np, "st,pins"); > + if (!pins) > + return -ENODATA; > + > + for_each_property_of_node(pins, pp) { > + /* Skip those we do not want to proceed */ > + if (!strcmp(pp->name, "name")) > + continue; > + > + if (pp && (pp->length/sizeof(__be32)) >= OF_GPIO_ARGS_MIN) { > + npins++; > + } else { > + pr_warn("Invalid st,pins in %s node\n", np->name); > + return -EINVAL; > + } > + } > + > + grp->npins = npins; > + grp->name = np->name; > + grp->pins = devm_kzalloc(info->dev, npins * sizeof(u32), GFP_KERNEL); > + grp->pin_conf = devm_kzalloc(info->dev, > + npins * sizeof(*conf), GFP_KERNEL); > + > + if (!grp->pins || !grp->pin_conf) > + return -ENOMEM; > + > + /* */ > + for_each_property_of_node(pins, pp) { > + if (!strcmp(pp->name, "name")) > + continue; > + nr_props = pp->length/sizeof(u32); > + list = pp->value; > + conf = &grp->pin_conf[i]; > + > + /* bank & offset */ > + phandle = be32_to_cpup(list++); > + pin = be32_to_cpup(list++); > + conf->pin = of_get_named_gpio(pins, pp->name, 0); > + conf->name = pp->name; > + grp->pins[i] = conf->pin; > + /* mux */ > + conf->altfunc = be32_to_cpup(list++); > + conf->config = 0; > + /* direction */ > + conf->config |= be32_to_cpup(list++); > + /* rt_type rt_delay rt_clk */ > + if (nr_props >= OF_GPIO_ARGS_MIN + OF_RT_ARGS_MIN) { > + /* rt_type */ > + conf->config |= be32_to_cpup(list++); > + /* rt_delay */ > + conf->config |= be32_to_cpup(list++); > + /* rt_clk */ > + if (nr_props > OF_GPIO_ARGS_MIN + OF_RT_ARGS_MIN) > + conf->config |= be32_to_cpup(list++); > + } > + i++; > + } > + of_node_put(pins); > + > + return 0; > +} > + > +static int st_pctl_parse_functions(struct device_node *np, > + struct st_pinctrl *info, u32 index, int *grp_index) > +{ > + struct device_node *child; > + struct st_pmx_func *func; > + struct st_pctl_group *grp; > + int ret, i; > + > + func = &info->functions[index]; > + func->name = np->name; > + func->ngroups = of_get_child_count(np); > + if (func->ngroups <= 0) { > + dev_err(info->dev, "No groups defined\n"); > + return -EINVAL; > + } > + func->groups = devm_kzalloc(info->dev, > + func->ngroups * sizeof(char *), GFP_KERNEL); > + if (!func->groups) > + return -ENOMEM; > + > + i = 0; > + for_each_child_of_node(np, child) { > + func->groups[i] = child->name; > + grp = &info->groups[*grp_index]; > + *grp_index += 1; > + ret = st_pctl_dt_parse_groups(child, grp, info, i++); > + if (ret) > + return ret; > + } > + dev_info(info->dev, "Function[%d\t name:%s,\tgroups:%d]\n", > + index, func->name, func->ngroups); > + > + return 0; > +} > + > +static struct gpio_chip st_gpio_template = { > + .request = st_gpio_request, > + .free = st_gpio_free, > + .get = st_gpio_get, > + .set = st_gpio_set, > + .direction_input = st_gpio_direction_input, > + .direction_output = st_gpio_direction_output, > + .ngpio = ST_GPIO_PINS_PER_BANK, > + .of_gpio_n_cells = 1, > + .of_xlate = st_gpio_xlate, > +}; > + > +static int st_gpiolib_register_bank(struct st_pinctrl *info, > + int bank_nr, struct device_node *np) > +{ > + struct st_gpio_bank *bank = &info->banks[bank_nr]; > + struct pinctrl_gpio_range *range = &bank->range; > + struct device *dev = info->dev; > + int bank_num = of_alias_get_id(np, "gpio"); > + struct resource res; > + int err; > + > + if (of_address_to_resource(np, 0, &res)) > + return -ENODEV; > + > + bank->base = devm_request_and_ioremap(dev, &res); > + if (!bank->base) { > + dev_err(dev, "Can't get IO memory mapping!\n"); > + return -ENODEV; > + } > + > + bank->gpio_chip = st_gpio_template; > + bank->gpio_chip.base = bank_num * ST_GPIO_PINS_PER_BANK; > + bank->gpio_chip.ngpio = ST_GPIO_PINS_PER_BANK; > + bank->gpio_chip.of_node = np; > + > + of_property_read_string(np, "st,bank-name", &range->name); > + bank->gpio_chip.label = range->name; > + > + range->id = bank_num; > + range->pin_base = range->base = range->id * ST_GPIO_PINS_PER_BANK; > + range->npins = bank->gpio_chip.ngpio; > + range->gc = &bank->gpio_chip; > + err = gpiochip_add(&bank->gpio_chip); > + if (err) { > + dev_err(dev, "Failed to add gpiochip(%d)!\n", bank_num); > + return err; > + } > + dev_info(dev, "%s bank added.\n", range->name); > + > + return 0; > +} > + > +static struct of_device_id st_pctl_of_match[] = { > + { .compatible = "st,stih415-sbc-pinctrl", .data = &stih415_sbc_data }, > + { .compatible = "st,stih415-rear-pinctrl", .data = &stih415_rear_data }, > + { .compatible = "st,stih415-left-pinctrl", .data = &stih415_left_data }, > + { .compatible = "st,stih415-right-pinctrl", > + .data = &stih415_right_data }, > + { .compatible = "st,stih415-front-pinctrl", > + .data = &stih415_front_data }, > + { .compatible = "st,stih416-sbc-pinctrl", .data = &stih416_data}, > + { .compatible = "st,stih416-front-pinctrl", .data = &stih416_data}, > + { .compatible = "st,stih416-rear-pinctrl", .data = &stih416_data}, > + { .compatible = "st,stih416-fvdp-fe-pinctrl", .data = &stih416_data}, > + { .compatible = "st,stih416-fvdp-lite-pinctrl", .data = &stih416_data}, > + { /* sentinel */ } > +}; > + > +static int st_pctl_probe_dt(struct platform_device *pdev, > + struct pinctrl_desc *pctl_desc, struct st_pinctrl *info) > +{ > + int ret = 0; > + int i = 0, j = 0, k = 0, bank; > + struct pinctrl_pin_desc *pdesc; > + struct device_node *np = pdev->dev.of_node; > + struct device_node *child; > + int grp_index = 0; > + > + st_pctl_dt_child_count(info, np); > + if (!info->nbanks) { > + dev_err(&pdev->dev, "you need atleast one gpio bank\n"); > + return -EINVAL; > + } > + > + dev_info(&pdev->dev, "nbanks = %d\n", info->nbanks); > + dev_info(&pdev->dev, "nfunctions = %d\n", info->nfunctions); > + dev_info(&pdev->dev, "ngroups = %d\n", info->ngroups); > + > + info->functions = devm_kzalloc(&pdev->dev, > + info->nfunctions * sizeof(*info->functions), GFP_KERNEL); > + > + info->groups = devm_kzalloc(&pdev->dev, > + info->ngroups * sizeof(*info->groups) , GFP_KERNEL); > + > + info->banks = devm_kzalloc(&pdev->dev, > + info->nbanks * sizeof(*info->banks), GFP_KERNEL); > + > + if (!info->functions || !info->groups || !info->banks) > + return -ENOMEM; > + > + info->regmap = syscon_regmap_lookup_by_phandle(np, "st,syscfg"); > + if (!info->regmap) { > + dev_err(info->dev, "No syscfg phandle specified\n"); > + return -ENOMEM; > + } > + info->data = of_match_node(st_pctl_of_match, np)->data; > + > + pctl_desc->npins = info->nbanks * ST_GPIO_PINS_PER_BANK; > + pdesc = devm_kzalloc(&pdev->dev, > + sizeof(*pdesc) * pctl_desc->npins, GFP_KERNEL); > + if (!pdesc) > + return -ENOMEM; > + > + pctl_desc->pins = pdesc; > + > + bank = 0; > + for_each_child_of_node(np, child) { > + if (of_property_read_bool(child, "gpio-controller")) { > + const char *bank_name = NULL; > + ret = st_gpiolib_register_bank(info, bank, child); > + if (ret) > + return ret; > + > + k = info->banks[bank].range.pin_base; > + bank_name = info->banks[bank].range.name; > + for (j = 0; j < ST_GPIO_PINS_PER_BANK; j++, k++) { > + pdesc->number = k; > + pdesc->name = kasprintf(GFP_KERNEL, "%s[%d]", > + bank_name, j); > + pdesc++; > + } > + st_parse_syscfgs(info, bank, child); > + bank++; > + } else { > + ret = st_pctl_parse_functions(child, info, > + i++, &grp_index); > + if (ret) { > + dev_err(&pdev->dev, "No functions found.\n"); > + return ret; > + } > + } > + } > + > + return 0; > +} > + > +static int st_pctl_probe(struct platform_device *pdev) > +{ > + struct st_pinctrl *info; > + struct pinctrl_desc *pctl_desc; > + int ret, i; > + > + if (!pdev->dev.of_node) { > + dev_err(&pdev->dev, "device node not found.\n"); > + return -EINVAL; > + } > + > + pctl_desc = devm_kzalloc(&pdev->dev, sizeof(*pctl_desc), GFP_KERNEL); > + if (!pctl_desc) > + return -ENOMEM; > + > + info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL); > + if (!info) > + return -ENOMEM; > + > + info->dev = &pdev->dev; > + platform_set_drvdata(pdev, info); > + ret = st_pctl_probe_dt(pdev, pctl_desc, info); > + if (ret) > + return ret; > + > + pctl_desc->owner = THIS_MODULE, > + pctl_desc->pctlops = &st_pctlops, > + pctl_desc->pmxops = &st_pmxops, > + pctl_desc->confops = &st_confops, > + pctl_desc->name = dev_name(&pdev->dev); > + > + info->pctl = pinctrl_register(pctl_desc, &pdev->dev, info); > + if (IS_ERR(info->pctl)) { > + dev_err(&pdev->dev, "Failed pinctrl registration\n"); > + return PTR_ERR(info->pctl); > + } > + > + for (i = 0; i < info->nbanks; i++) > + pinctrl_add_gpio_range(info->pctl, &info->banks[i].range); > + > + return 0; > +} > + > +static struct platform_driver st_pctl_driver = { > + .driver = { > + .name = "st-pinctrl", > + .owner = THIS_MODULE, > + .of_match_table = of_match_ptr(st_pctl_of_match), > + }, > + .probe = st_pctl_probe, > +}; > + > +static int __init st_pctl_init(void) > +{ > + return platform_driver_register(&st_pctl_driver); > +} > +arch_initcall(st_pctl_init); > -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/