Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1752716Ab3IVIGb (ORCPT ); Sun, 22 Sep 2013 04:06:31 -0400 Received: from newsmtp5.atmel.com ([204.2.163.5]:59100 "EHLO sjogate2.atmel.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752513Ab3IVIGY (ORCPT ); Sun, 22 Sep 2013 04:06:24 -0400 From: Bo Shen To: Thierry Reding Cc: plagnioj@jcrosoft.com, nicolas.ferre@atmel.com, linux-pwm@vger.kernel.org, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org, Bo Shen Subject: [PATCH v3] PWM: at91: add Atmel PWM controller driver Date: Sun, 22 Sep 2013 16:05:01 +0800 Message-Id: <1379837101-2165-1-git-send-email-voice.shen@atmel.com> X-Mailer: git-send-email 1.7.9.5 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 12098 Lines: 451 Add Atmel PWM controller driver based on PWM framework. This is the basic function implementation of Atmel PWM controller. It can work with PWM based led and backlight. Signed-off-by: Bo Shen --- Changes in v3: - change compatible string from "atmel,sama5-pwm" to "atmel,sama5d3-pwm" - Add PWM led example in binding documentation - Using micro replace hard code Changes in v2: - Address the comments from Thierry Reding .../devicetree/bindings/pwm/atmel-pwm.txt | 41 +++ drivers/pwm/Kconfig | 9 + drivers/pwm/Makefile | 1 + drivers/pwm/pwm-atmel.c | 335 ++++++++++++++++++++ 4 files changed, 386 insertions(+) create mode 100644 Documentation/devicetree/bindings/pwm/atmel-pwm.txt create mode 100644 drivers/pwm/pwm-atmel.c diff --git a/Documentation/devicetree/bindings/pwm/atmel-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt new file mode 100644 index 0000000..1c1a5fa --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt @@ -0,0 +1,41 @@ +Atmel PWM controller + +Required properties: + - compatible: should be one of: + - "atmel,at91sam9rl-pwm" + - "atmel,sama5d3-pwm" + - reg: physical base address and length of the controller's registers + - #pwm-cells: Should be 3. See pwm.txt in this directory for a + description of the cells format + +Example: + + pwm0: pwm@f8034000 { + compatible = "atmel,at91sam9rl-pwm"; + reg = <0xf8034000 0x400>; + #pwm-cells = <3>; + }; + +The following the pwm led based example: + + pwm0: pwm@f8034000 { + compatible = "atmel,at91sam9rl-pwm"; + reg = <0xf8034000 0x400>; + #pwm-cells = <3>; + }; + + pwdleds { + compatible = "pwm-leds"; + + d1 { + label = "d1"; + pwms = <&pwm0 3 5000 0> + max-brightness = <255>; + }; + + d2 { + label = "d2"; + pwms = <&pwm0 1 5000 1> + max-brightness = <255>; + }; + }; diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig index 75840b5..54237b9 100644 --- a/drivers/pwm/Kconfig +++ b/drivers/pwm/Kconfig @@ -41,6 +41,15 @@ config PWM_AB8500 To compile this driver as a module, choose M here: the module will be called pwm-ab8500. +config PWM_ATMEL + tristate "Atmel PWM support" + depends on ARCH_AT91 + help + Generic PWM framework driver for Atmel SoC. + + To compile this driver as a module, choose M here: the module + will be called pwm-atmel. + config PWM_ATMEL_TCB tristate "Atmel TC Block PWM support" depends on ATMEL_TCLIB && OF diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile index 77a8c18..5b193f8 100644 --- a/drivers/pwm/Makefile +++ b/drivers/pwm/Makefile @@ -1,6 +1,7 @@ obj-$(CONFIG_PWM) += core.o obj-$(CONFIG_PWM_SYSFS) += sysfs.o obj-$(CONFIG_PWM_AB8500) += pwm-ab8500.o +obj-$(CONFIG_PWM_ATMEL) += pwm-atmel.o obj-$(CONFIG_PWM_ATMEL_TCB) += pwm-atmel-tcb.o obj-$(CONFIG_PWM_BFIN) += pwm-bfin.o obj-$(CONFIG_PWM_IMX) += pwm-imx.o diff --git a/drivers/pwm/pwm-atmel.c b/drivers/pwm/pwm-atmel.c new file mode 100644 index 0000000..9c86dfe --- /dev/null +++ b/drivers/pwm/pwm-atmel.c @@ -0,0 +1,335 @@ +/* + * Driver for Atmel Pulse Width Modulation Controller + * + * Copyright (C) 2013 Atmel Corporation + * Bo Shen + * + * Licensed under GPLv2. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* The following is global registers for PWM controller */ +#define PWM_ENA 0x04 +#define PWM_DIS 0x08 +#define PWM_SR 0x0C +/* bit field in SR */ +#define PWM_SR_ALL_CH_ON 0x0F + +/* The following register is PWM channel related registers */ +#define PWM_CH_REG_OFFSET 0x200 + +#define PWM_CMR 0x0 +/* bit field in CMR */ +#define PWM_CMR_CPOL (1 << 9) +#define PWM_CMR_UPD_CDTY (1 << 10) + +/* The following registers for PWM v1 */ +#define PWMv1_CDTY 0x04 +#define PWMv1_CPRD 0x08 +#define PWMv1_CUPD 0x10 + +/* The following registers for PWM v2 */ +#define PWMv2_CDTY 0x04 +#define PWMv2_CDTYUPD 0x08 +#define PWMv2_CPRD 0x0C +#define PWMv2_CPRDUPD 0x10 + +/* max value for duty and period */ +/* + * Although the duty and period register is 32 bit, + * however only the LSB 16 bits are significant. + */ +#define PWM_MAX_DTY 0xFFFF +#define PWM_MAX_PRD 0xFFFF +#define PRD_MAX_PRES 10 + +struct atmel_pwm_chip { + struct pwm_chip chip; + struct clk *clk; + void __iomem *base; + + void (*config)(struct pwm_chip *chip, struct pwm_device *pwm, + int dty, int prd); +}; + +static inline struct atmel_pwm_chip *to_atmel_pwm_chip(struct pwm_chip *chip) +{ + return container_of(chip, struct atmel_pwm_chip, chip); +} + +static inline u32 atmel_pwm_readl(struct atmel_pwm_chip *chip, + unsigned long offset) +{ + return readl(chip->base + offset); +} + +static inline void atmel_pwm_writel(struct atmel_pwm_chip *chip, + unsigned long offset, unsigned long val) +{ + writel(val, chip->base + offset); +} + +static inline u32 atmel_pwm_ch_readl(struct atmel_pwm_chip *chip, + unsigned int ch, unsigned long offset) +{ + return readl(chip->base + PWM_CH_REG_OFFSET + ch * 0x20 + offset); +} + +static inline void atmel_pwm_ch_writel(struct atmel_pwm_chip *chip, + unsigned int ch, unsigned long offset, + unsigned long val) +{ + writel(val, chip->base + PWM_CH_REG_OFFSET + ch * 0x20 + offset); +} + +static int atmel_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm, + int duty_ns, int period_ns) +{ + struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip); + unsigned long clk_rate, prd, dty; + unsigned long long val, div; + int ret, pres = 0; + + clk_rate = clk_get_rate(atmel_pwm->clk); + div = clk_rate; + + /* Calculate the period cycles */ + while (div > PWM_MAX_PRD) { + div = clk_rate / (1 << pres); + div = div * period_ns; + /* 1/Hz = 100000000 ns */ + do_div(div, 1000000000); + + if (pres++ > PRD_MAX_PRES) { + pr_err("PRES is bigger than maximum pre-scaler\n"); + return -EINVAL; + } + } + + /* Calculate the duty cycles */ + prd = div; + div *= duty_ns; + do_div(div, period_ns); + dty = div; + + ret = clk_enable(atmel_pwm->clk); + if (ret) { + pr_err("Failed to enable pwm clock\n"); + return ret; + } + + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWM_CMR, pres); + atmel_pwm->config(chip, pwm, dty, prd); + + /* Check whether need to disable clock */ + val = atmel_pwm_readl(atmel_pwm, PWM_SR); + if ((val & PWM_SR_ALL_CH_ON) == 0) + clk_disable(atmel_pwm->clk); + + return 0; +} + +static void atmel_pwm_config_v1(struct pwm_chip *chip, struct pwm_device *pwm, + int dty, int prd) +{ + struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip); + unsigned int val; + + /* + * If the PWM channel is disabled, write value to duty and period + * registers directly. + * If the PWM channel is enabled, using the update register, it needs + * to set bit 10 of CMR to 0 + */ + if (test_bit(PWMF_ENABLED, &pwm->flags)) { + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWMv1_CUPD, dty); + + val = atmel_pwm_ch_readl(atmel_pwm, pwm->hwpwm, PWM_CMR); + val &= ~PWM_CMR_UPD_CDTY; + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWM_CMR, val); + } else { + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWMv1_CDTY, dty); + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWMv1_CPRD, prd); + } +} + +static void atmel_pwm_config_v2(struct pwm_chip *chip, struct pwm_device *pwm, + int dty, int prd) +{ + struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip); + + /* + * If the PWM channel is disabled, write value to duty and period + * registers directly. + * If the PWM channel is enabled, using the duty update register to + * update the value. + */ + if (test_bit(PWMF_ENABLED, &pwm->flags)) { + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWMv2_CDTYUPD, dty); + } else { + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWMv2_CDTY, dty); + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWMv2_CPRD, prd); + } +} + +static int atmel_pwm_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm, + enum pwm_polarity polarity) +{ + struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip); + u32 val = 0; + int ret; + + ret = clk_enable(atmel_pwm->clk); + if (ret) { + pr_err("failed to enable pwm clock\n"); + return ret; + } + + if (polarity == PWM_POLARITY_NORMAL) + val &= ~PWM_CMR_CPOL; + else + val |= PWM_CMR_CPOL; + + atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWM_CMR, val); + + clk_disable(atmel_pwm->clk); + + return 0; +} + +static int atmel_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm) +{ + struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip); + + clk_prepare_enable(atmel_pwm->clk); + + atmel_pwm_writel(atmel_pwm, PWM_ENA, 1 << pwm->hwpwm); + + return 0; +} + +static void atmel_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm) +{ + struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip); + u32 val; + + atmel_pwm_writel(atmel_pwm, PWM_DIS, 1 << pwm->hwpwm); + + val = atmel_pwm_readl(atmel_pwm, PWM_SR); + if ((val & PWM_SR_ALL_CH_ON) == 0) + clk_disable(atmel_pwm->clk); +} + +static const struct pwm_ops atmel_pwm_ops = { + .config = atmel_pwm_config, + .set_polarity = atmel_pwm_set_polarity, + .enable = atmel_pwm_enable, + .disable = atmel_pwm_disable, + .owner = THIS_MODULE, +}; + +struct atmel_pwm_data { + void (*config)(struct pwm_chip *chip, struct pwm_device *pwm, + int dty, int prd); +}; + +static const struct atmel_pwm_data atmel_pwm_data_v1 = { + .config = atmel_pwm_config_v1, +}; + +static const struct atmel_pwm_data atmel_pwm_data_v2 = { + .config = atmel_pwm_config_v2, +}; + +#ifdef CONFIG_OF +static const struct of_device_id atmel_pwm_dt_ids[] = { + { + .compatible = "atmel,at91sam9rl-pwm", + .data = &atmel_pwm_data_v1, + }, { + .compatible = "atmel,sama5d3-pwm", + .data = &atmel_pwm_data_v2, + }, { + /* sentinel */ + }, +}; +MODULE_DEVICE_TABLE(of, atmel_pwm_dt_ids); +#endif + +static int atmel_pwm_probe(struct platform_device *pdev) +{ + const struct of_device_id *of_id = + of_match_device(atmel_pwm_dt_ids, &pdev->dev); + const struct atmel_pwm_data *data; + struct atmel_pwm_chip *atmel_pwm; + struct resource *res; + int ret; + + atmel_pwm = devm_kzalloc(&pdev->dev, sizeof(*atmel_pwm), GFP_KERNEL); + if (!atmel_pwm) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) + return -ENODEV; + + atmel_pwm->base = devm_ioremap_resource(&pdev->dev, res); + + atmel_pwm->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(atmel_pwm->clk)) + return PTR_ERR(atmel_pwm->clk); + clk_prepare(atmel_pwm->clk); + + atmel_pwm->chip.dev = &pdev->dev; + atmel_pwm->chip.ops = &atmel_pwm_ops; + atmel_pwm->chip.of_xlate = of_pwm_xlate_with_flags; + atmel_pwm->chip.of_pwm_n_cells = 3; + atmel_pwm->chip.base = -1; + atmel_pwm->chip.npwm = 4; + + data = of_id->data; + atmel_pwm->config = data->config; + + ret = pwmchip_add(&atmel_pwm->chip); + if (ret < 0) { + dev_err(&pdev->dev, "failed to add pwm chip %d\n", ret); + return ret; + } + + platform_set_drvdata(pdev, atmel_pwm); + + return 0; +} + +static int atmel_pwm_remove(struct platform_device *pdev) +{ + struct atmel_pwm_chip *atmel_pwm = platform_get_drvdata(pdev); + + clk_unprepare(atmel_pwm->clk); + + return pwmchip_remove(&atmel_pwm->chip); +} + +static struct platform_driver atmel_pwm_driver = { + .driver = { + .name = "atmel-pwm", + .of_match_table = of_match_ptr(atmel_pwm_dt_ids), + }, + .probe = atmel_pwm_probe, + .remove = atmel_pwm_remove, +}; +module_platform_driver(atmel_pwm_driver); + +MODULE_ALIAS("platform:atmel-pwm"); +MODULE_AUTHOR("Bo Shen "); +MODULE_DESCRIPTION("Atmel PWM driver"); +MODULE_LICENSE("GPL v2"); -- 1.7.9.5 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/