Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S932383AbaFKJN7 (ORCPT ); Wed, 11 Jun 2014 05:13:59 -0400 Received: from arroyo.ext.ti.com ([192.94.94.40]:59763 "EHLO arroyo.ext.ti.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1755530AbaFKI5k (ORCPT ); Wed, 11 Jun 2014 04:57:40 -0400 From: Roger Quadros To: , , CC: , , , , , , , , , Roger Quadros Subject: [PATCH 08/36] mtd: nand: omap: Copy platform data parameters to omap_nand_info data Date: Wed, 11 Jun 2014 11:56:13 +0300 Message-ID: <1402477001-31132-9-git-send-email-rogerq@ti.com> X-Mailer: git-send-email 1.8.3.2 In-Reply-To: <1402477001-31132-1-git-send-email-rogerq@ti.com> References: <1402477001-31132-1-git-send-email-rogerq@ti.com> MIME-Version: 1.0 Content-Type: text/plain Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Copy all the platform data parameters to the driver's local data structure 'omap_nand_info' and use it in the entire driver. This will make it easer for device tree migration. Signed-off-by: Roger Quadros --- drivers/mtd/nand/omap2.c | 27 ++++++++++++++++++--------- 1 file changed, 18 insertions(+), 9 deletions(-) diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c index bb41796..e205863 100644 --- a/drivers/mtd/nand/omap2.c +++ b/drivers/mtd/nand/omap2.c @@ -184,15 +184,19 @@ static struct nand_ecclayout omap_oobinfo; struct omap_nand_info { struct nand_hw_control controller; - struct omap_nand_platform_data *pdata; struct mtd_info mtd; struct nand_chip nand; struct platform_device *pdev; int gpmc_cs; + bool dev_ready; + enum nand_io xfer_type; + int devsize; + enum omap_ecc ecc_opt; + struct device_node *elm_of_node; + unsigned long phys_base; void __iomem *gpmc_base; - enum omap_ecc ecc_opt; struct completion comp; struct dma_chan *dma; int gpmc_irq; @@ -1708,6 +1712,11 @@ static int omap_nand_probe(struct platform_device *pdev) info->gpmc_cs = pdata->cs; info->of_node = pdata->of_node; info->ecc_opt = pdata->ecc_opt; + info->dev_ready = pdata->dev_ready; + info->xfer_type = pdata->xfer_type; + info->devsize = pdata->devsize; + info->elm_of_node = pdata->elm_of_node; + mtd = &info->mtd; mtd->priv = &info->nand; mtd->name = dev_name(&pdev->dev); @@ -1762,7 +1771,7 @@ static int omap_nand_probe(struct platform_device *pdev) * chip delay which is slightly more than tR (AC Timing) of the NAND * device and read status register until you get a failure or success */ - if (pdata->dev_ready) { + if (info->dev_ready) { nand_chip->dev_ready = omap_dev_ready; nand_chip->chip_delay = 0; } else { @@ -1771,7 +1780,7 @@ static int omap_nand_probe(struct platform_device *pdev) } /* scan NAND device connected to chip controller */ - nand_chip->options |= pdata->devsize & NAND_BUSWIDTH_16; + nand_chip->options |= info->devsize & NAND_BUSWIDTH_16; if (nand_scan_ident(mtd, 1, NULL)) { pr_err("nand device scan failed, may be bus-width mismatch\n"); err = -ENXIO; @@ -1779,14 +1788,14 @@ static int omap_nand_probe(struct platform_device *pdev) } /* check for small page devices */ - if ((mtd->oobsize < 64) && (pdata->ecc_opt != OMAP_ECC_HAM1_CODE_HW)) { + if ((mtd->oobsize < 64) && (info->ecc_opt != OMAP_ECC_HAM1_CODE_HW)) { pr_err("small page devices are not supported\n"); err = -EINVAL; goto return_error; } /* re-populate low-level callbacks based on xfer modes */ - switch (pdata->xfer_type) { + switch (info->xfer_type) { case NAND_OMAP_PREFETCH_POLLED: nand_chip->read_buf = omap_read_buf_pref; nand_chip->write_buf = omap_write_buf_pref; @@ -1849,7 +1858,7 @@ static int omap_nand_probe(struct platform_device *pdev) default: dev_err(&pdev->dev, - "xfer_type(%d) not supported!\n", pdata->xfer_type); + "xfer_type(%d) not supported!\n", info->xfer_type); err = -EINVAL; goto return_error; } @@ -1945,7 +1954,7 @@ static int omap_nand_probe(struct platform_device *pdev) ecclayout->oobfree->offset = ecclayout->eccpos[ecclayout->eccbytes - 1] + 1; /* This ECC scheme requires ELM H/W block */ - if (is_elm_present(info, pdata->elm_of_node, BCH4_ECC) < 0) { + if (is_elm_present(info, info->elm_of_node, BCH4_ECC) < 0) { pr_err("nand: error: could not initialize ELM\n"); err = -ENODEV; goto return_error; @@ -2011,7 +2020,7 @@ static int omap_nand_probe(struct platform_device *pdev) nand_chip->ecc.read_page = omap_read_page_bch; nand_chip->ecc.write_page = omap_write_page_bch; /* This ECC scheme requires ELM H/W block */ - err = is_elm_present(info, pdata->elm_of_node, BCH8_ECC); + err = is_elm_present(info, info->elm_of_node, BCH8_ECC); if (err < 0) { pr_err("nand: error: could not initialize ELM\n"); goto return_error; -- 1.8.3.2 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/