Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1753152AbaJAQbx (ORCPT ); Wed, 1 Oct 2014 12:31:53 -0400 Received: from ns.mm-sol.com ([37.157.136.199]:59691 "EHLO extserv.mm-sol.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751575AbaJAQbC (ORCPT ); Wed, 1 Oct 2014 12:31:02 -0400 From: "Ivan T. Ivanov" To: Linus Walleij , Grant Likely , Rob Herring Cc: "Ivan T. Ivanov" , Bjorn Andersson , linux-kernel@vger.kernel.org, devicetree@vger.kernel.org, linux-arm-msm@vger.kernel.org Subject: [PATCH v5 3/4] pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver Date: Wed, 1 Oct 2014 19:30:57 +0300 Message-Id: <1412181058-29179-4-git-send-email-iivanov@mm-sol.com> X-Mailer: git-send-email 1.9.1 In-Reply-To: <1412181058-29179-1-git-send-email-iivanov@mm-sol.com> References: <1412181058-29179-1-git-send-email-iivanov@mm-sol.com> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org This is the pinctrl, pinmux, pinconf and gpiolib driver for the Qualcomm GPIO sub-function blocks found in the PMIC chips. Signed-off-by: Ivan T. Ivanov --- drivers/pinctrl/qcom/Kconfig | 13 + drivers/pinctrl/qcom/Makefile | 1 + drivers/pinctrl/qcom/pinctrl-spmi-gpio.c | 937 +++++++++++++++++++++++++++++++ 3 files changed, 951 insertions(+) create mode 100644 drivers/pinctrl/qcom/pinctrl-spmi-gpio.c diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig index d160a71..e376dd3 100644 --- a/drivers/pinctrl/qcom/Kconfig +++ b/drivers/pinctrl/qcom/Kconfig @@ -39,4 +39,17 @@ config PINCTRL_MSM8X74 This is the pinctrl, pinmux, pinconf and gpiolib driver for the Qualcomm TLMM block found in the Qualcomm 8974 platform. +config PINCTRL_QCOM_SPMI_PMIC + tristate "Qualcomm SPMI PMIC pin controller driver" + depends on GPIOLIB && OF && SPMI + select REGMAP_SPMI + select PINMUX + select PINCONF + select GENERIC_PINCONF + help + This is the pinctrl, pinmux, pinconf and gpiolib driver for the + Qualcomm GPIO and MPP blocks found in the Qualcomm PMIC's chips, + which are using SPMI for communication with SoC. Example PMIC's + devices are pm8841, pm8941 and pma8084. + endif diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile index 2a02602..fc86fe4 100644 --- a/drivers/pinctrl/qcom/Makefile +++ b/drivers/pinctrl/qcom/Makefile @@ -4,3 +4,4 @@ obj-$(CONFIG_PINCTRL_APQ8064) += pinctrl-apq8064.o obj-$(CONFIG_PINCTRL_IPQ8064) += pinctrl-ipq8064.o obj-$(CONFIG_PINCTRL_MSM8960) += pinctrl-msm8960.o obj-$(CONFIG_PINCTRL_MSM8X74) += pinctrl-msm8x74.o +obj-$(CONFIG_PINCTRL_QCOM_SPMI_PMIC) += pinctrl-spmi-gpio.o diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c new file mode 100644 index 0000000..778a474 --- /dev/null +++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c @@ -0,0 +1,937 @@ +/* + * Copyright (c) 2012-2014, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#include "../core.h" +#include "../pinctrl-utils.h" + +#define PMIC_GPIO_ADDRESS_RANGE 0x100 + +/* type and subtype registers base address offsets */ +#define PMIC_GPIO_REG_TYPE 0x4 +#define PMIC_GPIO_REG_SUBTYPE 0x5 + +/* GPIO peripheral type and subtype out_values */ +#define PMIC_GPIO_TYPE 0x10 +#define PMIC_GPIO_SUBTYPE_GPIO_4CH 0x1 +#define PMIC_GPIO_SUBTYPE_GPIOC_4CH 0x5 +#define PMIC_GPIO_SUBTYPE_GPIO_8CH 0x9 +#define PMIC_GPIO_SUBTYPE_GPIOC_8CH 0xd + +#define PMIC_MPP_REG_RT_STS 0x10 +#define PMIC_MPP_REG_RT_STS_VAL_MASK 0x1 + +/* control register base address offsets */ +#define PMIC_GPIO_REG_MODE_CTL 0x40 +#define PMIC_GPIO_REG_DIG_VIN_CTL 0x41 +#define PMIC_GPIO_REG_DIG_PULL_CTL 0x42 +#define PMIC_GPIO_REG_DIG_OUT_CTL 0x45 +#define PMIC_GPIO_REG_EN_CTL 0x46 + +/* PMIC_GPIO_REG_MODE_CTL */ +#define PMIC_GPIO_REG_MODE_VALUE_SHIFT 0x1 +#define PMIC_GPIO_REG_MODE_FUNCTION_SHIFT 1 +#define PMIC_GPIO_REG_MODE_FUNCTION_MASK 0x7 +#define PMIC_GPIO_REG_MODE_DIR_SHIFT 4 +#define PMIC_GPIO_REG_MODE_DIR_MASK 0x7 + +/* PMIC_GPIO_REG_DIG_VIN_CTL */ +#define PMIC_GPIO_REG_VIN_SHIFT 0 +#define PMIC_GPIO_REG_VIN_MASK 0x7 + +/* PMIC_GPIO_REG_DIG_PULL_CTL */ +#define PMIC_GPIO_REG_PULL_SHIFT 0 +#define PMIC_GPIO_REG_PULL_MASK 0x7 + +#define PMIC_GPIO_PULL_DOWN 4 +#define PMIC_GPIO_PULL_DISABLE 5 + +/* PMIC_GPIO_REG_DIG_OUT_CTL */ +#define PMIC_GPIO_REG_OUT_STRENGTH_SHIFT 0 +#define PMIC_GPIO_REG_OUT_STRENGTH_MASK 0x3 +#define PMIC_GPIO_REG_OUT_TYPE_SHIFT 4 +#define PMIC_GPIO_REG_OUT_TYPE_MASK 0x3 + +/* + * Output type - indicates pin should be configured as push-pull, + * open drain or open source. + */ +#define PMIC_GPIO_OUT_BUF_CMOS 0 +#define PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS 1 +#define PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS 2 + +/* PMIC_GPIO_REG_EN_CTL */ +#define PMIC_GPIO_REG_MASTER_EN_SHIFT 7 + +#define PMIC_GPIO_PHYSICAL_OFFSET 1 + +/* Qualcomm specific pin configurations */ +#define PMIC_GPIO_CONF_PULL_UP (PIN_CONFIG_END + 1) +#define PMIC_GPIO_CONF_STRENGTH (PIN_CONFIG_END + 2) + +/** + * struct pmic_gpio_pad - keep current GPIO settings + * @base: Address base in SPMI device. + * @irq: IRQ number which this GPIO generate. + * @is_enabled: Set to false when GPIO should be put in high Z state. + * @out_value: Cached pin output value + * @have_buffer: Set to true if GPIO output could be configured in push-pull, + * open-drain or open-source mode. + * @output_enabled: Set to true if GPIO output logic is enabled. + * @input_enabled: Set to true if GPIO input buffer logic is enabled. + * @num_sources: Number of power-sources supported by this GPIO. + * @power_source: Current power-source used. + * @buffer_type: Push-pull, open-drain or open-source. + * @pullup: Constant current which flow trough GPIO output buffer. + * @strength: No, Low, Medium, High + * @function: See pmic_gpio_functions[] + */ +struct pmic_gpio_pad { + u16 base; + int irq; + bool is_enabled; + bool out_value; + bool have_buffer; + bool output_enabled; + bool input_enabled; + unsigned int num_sources; + unsigned int power_source; + unsigned int buffer_type; + unsigned int pullup; + unsigned int strength; + unsigned int function; +}; + +struct pmic_gpio_state { + struct device *dev; + struct regmap *map; + struct pinctrl_dev *ctrl; + struct gpio_chip chip; +}; + +struct pmic_gpio_bindings { + const char *property; + unsigned param; +}; + +static struct pmic_gpio_bindings pmic_gpio_bindings[] = { + {"qcom,pull-up-strength", PMIC_GPIO_CONF_PULL_UP}, + {"qcom,drive-strength", PMIC_GPIO_CONF_STRENGTH}, +}; + +static const char *const pmic_gpio_groups[] = { + "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", "gpio8", + "gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", "gpio15", + "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21", "gpio22", + "gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28", "gpio29", + "gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35", "gpio36", +}; + +static const char *const pmic_gpio_functions[] = { + PMIC_GPIO_FUNC_NORMAL, PMIC_GPIO_FUNC_PAIRED, + PMIC_GPIO_FUNC_FUNC1, PMIC_GPIO_FUNC_FUNC2, + PMIC_GPIO_FUNC_DTEST1, PMIC_GPIO_FUNC_DTEST2, + PMIC_GPIO_FUNC_DTEST3, PMIC_GPIO_FUNC_DTEST4, +}; + +static inline struct pmic_gpio_state *to_gpio_state(struct gpio_chip *chip) +{ + return container_of(chip, struct pmic_gpio_state, chip); +}; + +static int pmic_gpio_read(struct pmic_gpio_state *state, + struct pmic_gpio_pad *pad, unsigned int addr) +{ + unsigned int val; + int ret; + + ret = regmap_read(state->map, pad->base + addr, &val); + if (ret < 0) + dev_err(state->dev, "read 0x%x failed\n", addr); + else + ret = val; + + return ret; +} + +static int pmic_gpio_write(struct pmic_gpio_state *state, + struct pmic_gpio_pad *pad, unsigned int addr, + unsigned int val) +{ + int ret; + + ret = regmap_write(state->map, pad->base + addr, val); + if (ret < 0) + dev_err(state->dev, "write 0x%x failed\n", addr); + + return ret; +} + +static int pmic_gpio_get_groups_count(struct pinctrl_dev *pctldev) +{ + /* Every PIN is a group */ + return pctldev->desc->npins; +} + +static const char *pmic_gpio_get_group_name(struct pinctrl_dev *pctldev, + unsigned pin) +{ + return pctldev->desc->pins[pin].name; +} + +static int pmic_gpio_get_group_pins(struct pinctrl_dev *pctldev, unsigned pin, + const unsigned **pins, unsigned *num_pins) +{ + *pins = &pctldev->desc->pins[pin].number; + *num_pins = 1; + return 0; +} + +static int pmic_gpio_parse_dt_config(struct device_node *np, + struct pinctrl_dev *pctldev, + unsigned long **configs, + unsigned int *nconfs) +{ + struct pmic_gpio_bindings *par; + unsigned long cfg; + int ret, i; + u32 val; + + for (i = 0; i < ARRAY_SIZE(pmic_gpio_bindings); i++) { + par = &pmic_gpio_bindings[i]; + ret = of_property_read_u32(np, par->property, &val); + + /* property not found */ + if (ret == -EINVAL) + continue; + + /* use zero as default value */ + if (ret) + val = 0; + + dev_dbg(pctldev->dev, "found %s with value %u\n", + par->property, val); + + cfg = pinconf_to_config_packed(par->param, val); + + ret = pinctrl_utils_add_config(pctldev, configs, nconfs, cfg); + if (ret) + return ret; + } + + return 0; +} + +static int pmic_gpio_dt_subnode_to_map(struct pinctrl_dev *pctldev, + struct device_node *np, + struct pinctrl_map **map, + unsigned *reserv, unsigned *nmaps, + enum pinctrl_map_type type) +{ + unsigned long *configs = NULL; + unsigned nconfs = 0; + struct property *prop; + const char *group; + int ret; + + ret = pmic_gpio_parse_dt_config(np, pctldev, &configs, &nconfs); + if (ret < 0) + return ret; + + if (!nconfs) + return 0; + + ret = of_property_count_strings(np, "pins"); + if (ret < 0) + goto exit; + + ret = pinctrl_utils_reserve_map(pctldev, map, reserv, nmaps, ret); + if (ret < 0) + goto exit; + + of_property_for_each_string(np, "pins", prop, group) { + ret = pinctrl_utils_add_map_configs(pctldev, map, + reserv, nmaps, group, + configs, nconfs, type); + if (ret < 0) + break; + } +exit: + kfree(configs); + return ret; +} + +static int pmic_gpio_dt_node_to_map(struct pinctrl_dev *pctldev, + struct device_node *np_config, + struct pinctrl_map **map, unsigned *nmaps) +{ + enum pinctrl_map_type type; + struct device_node *np; + unsigned reserv; + int ret; + + ret = 0; + *map = NULL; + *nmaps = 0; + reserv = 0; + type = PIN_MAP_TYPE_CONFIGS_GROUP; + + for_each_child_of_node(np_config, np) { + ret = pinconf_generic_dt_subnode_to_map(pctldev, np, map, + &reserv, nmaps, type); + if (ret) + break; + + ret = pmic_gpio_dt_subnode_to_map(pctldev, np, map, &reserv, + nmaps, type); + if (ret) + break; + } + + if (ret < 0) + pinctrl_utils_dt_free_map(pctldev, *map, *nmaps); + + return ret; +} + +static const struct pinctrl_ops pmic_gpio_pinctrl_ops = { + .get_groups_count = pmic_gpio_get_groups_count, + .get_group_name = pmic_gpio_get_group_name, + .get_group_pins = pmic_gpio_get_group_pins, + .dt_node_to_map = pmic_gpio_dt_node_to_map, + .dt_free_map = pinctrl_utils_dt_free_map, +}; + +static int pmic_gpio_get_functions_count(struct pinctrl_dev *pctldev) +{ + return ARRAY_SIZE(pmic_gpio_functions); +} + +static const char *pmic_gpio_get_function_name(struct pinctrl_dev *pctldev, + unsigned function) +{ + return pmic_gpio_functions[function]; +} + +static int pmic_gpio_get_function_groups(struct pinctrl_dev *pctldev, + unsigned function, + const char *const **groups, + unsigned *const num_qgroups) +{ + *groups = pmic_gpio_groups; + *num_qgroups = pctldev->desc->npins; + return 0; +} + +static int pmic_gpio_pinmux_enable(struct pinctrl_dev *pctldev, + unsigned function, unsigned pin) +{ + struct pmic_gpio_state *state = pinctrl_dev_get_drvdata(pctldev); + struct pmic_gpio_pad *pad; + unsigned int val; + int ret; + + pad = pctldev->desc->pins[pin].drv_data; + + pad->function = function; + + val = 0; + if (pad->output_enabled) { + if (pad->input_enabled) + val = 2; + else + val = 1; + } + + val |= pad->function << PMIC_GPIO_REG_MODE_FUNCTION_SHIFT; + val |= pad->out_value & PMIC_GPIO_REG_MODE_VALUE_SHIFT; + + ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_MODE_CTL, val); + if (ret < 0) + return ret; + + val = pad->is_enabled << PMIC_GPIO_REG_MASTER_EN_SHIFT; + + return pmic_gpio_write(state, pad, PMIC_GPIO_REG_EN_CTL, val); +} + +static const struct pinmux_ops pmic_gpio_pinmux_ops = { + .get_functions_count = pmic_gpio_get_functions_count, + .get_function_name = pmic_gpio_get_function_name, + .get_function_groups = pmic_gpio_get_function_groups, + .enable = pmic_gpio_pinmux_enable, +}; + +static int pmic_gpio_config_get(struct pinctrl_dev *pctldev, + unsigned int pin, unsigned long *config) +{ + unsigned param = pinconf_to_config_param(*config); + struct pmic_gpio_pad *pad; + unsigned arg; + + pad = pctldev->desc->pins[pin].drv_data; + + switch (param) { + case PIN_CONFIG_DRIVE_PUSH_PULL: + arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_CMOS; + break; + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS; + break; + case PIN_CONFIG_DRIVE_OPEN_SOURCE: + arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS; + break; + case PIN_CONFIG_BIAS_PULL_DOWN: + arg = pad->pullup == PMIC_GPIO_PULL_DOWN; + break; + case PIN_CONFIG_BIAS_DISABLE: + arg = pad->pullup = PMIC_GPIO_PULL_DISABLE; + break; + case PIN_CONFIG_BIAS_PULL_UP: + arg = pad->pullup == PMIC_GPIO_PULL_UP_30; + break; + case PIN_CONFIG_BIAS_HIGH_IMPEDANCE: + arg = !pad->is_enabled; + break; + case PIN_CONFIG_POWER_SOURCE: + arg = pad->power_source; + break; + case PIN_CONFIG_INPUT_ENABLE: + arg = pad->input_enabled; + break; + case PIN_CONFIG_OUTPUT: + arg = pad->out_value; + break; + case PMIC_GPIO_CONF_PULL_UP: + arg = pad->pullup; + break; + case PMIC_GPIO_CONF_STRENGTH: + arg = pad->strength; + break; + default: + return -EINVAL; + } + + *config = pinconf_to_config_packed(param, arg); + return 0; +} + +static int pmic_gpio_config_set(struct pinctrl_dev *pctldev, unsigned int pin, + unsigned long *configs, unsigned nconfs) +{ + struct pmic_gpio_state *state = pinctrl_dev_get_drvdata(pctldev); + struct pmic_gpio_pad *pad; + unsigned param, arg; + unsigned int val; + int i, ret; + + pad = pctldev->desc->pins[pin].drv_data; + + for (i = 0; i < nconfs; i++) { + param = pinconf_to_config_param(configs[i]); + arg = pinconf_to_config_argument(configs[i]); + + switch (param) { + case PIN_CONFIG_DRIVE_PUSH_PULL: + pad->buffer_type = PMIC_GPIO_OUT_BUF_CMOS; + break; + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + if (!pad->have_buffer) + return -EINVAL; + pad->buffer_type = PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS; + break; + case PIN_CONFIG_DRIVE_OPEN_SOURCE: + if (!pad->have_buffer) + return -EINVAL; + pad->buffer_type = PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS; + break; + case PIN_CONFIG_BIAS_DISABLE: + pad->pullup = PMIC_GPIO_PULL_DISABLE; + break; + case PIN_CONFIG_BIAS_PULL_UP: + pad->pullup = PMIC_GPIO_PULL_UP_30; + break; + case PIN_CONFIG_BIAS_PULL_DOWN: + if (arg) + pad->pullup = PMIC_GPIO_PULL_DOWN; + else + pad->pullup = PMIC_GPIO_PULL_DISABLE; + break; + case PIN_CONFIG_BIAS_HIGH_IMPEDANCE: + pad->is_enabled = false; + break; + case PIN_CONFIG_POWER_SOURCE: + if (arg > pad->num_sources) + return -EINVAL; + pad->power_source = arg; + break; + case PIN_CONFIG_INPUT_ENABLE: + pad->input_enabled = arg ? true : false; + break; + case PIN_CONFIG_OUTPUT: + pad->output_enabled = true; + pad->out_value = arg; + break; + case PMIC_GPIO_CONF_PULL_UP: + if (arg > PMIC_GPIO_PULL_UP_1P5_30) + return -EINVAL; + pad->pullup = arg; + break; + case PMIC_GPIO_CONF_STRENGTH: + if (arg > PMIC_GPIO_STRENGTH_LOW) + return -EINVAL; + pad->strength = arg; + break; + default: + return -EINVAL; + } + } + + val = pad->power_source << PMIC_GPIO_REG_VIN_SHIFT; + + ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_DIG_VIN_CTL, val); + if (ret < 0) + return ret; + + val = pad->pullup << PMIC_GPIO_REG_PULL_SHIFT; + + ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_DIG_PULL_CTL, val); + if (ret < 0) + return ret; + + val = pad->buffer_type << PMIC_GPIO_REG_OUT_TYPE_SHIFT; + val = pad->strength << PMIC_GPIO_REG_OUT_STRENGTH_SHIFT; + + ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_DIG_OUT_CTL, val); + if (ret < 0) + return ret; + + val = 0; + if (pad->output_enabled) { + if (pad->input_enabled) + val = 2; + else + val = 1; + } + + val = val << PMIC_GPIO_REG_MODE_DIR_SHIFT; + val |= pad->function << PMIC_GPIO_REG_MODE_FUNCTION_SHIFT; + val |= pad->out_value & PMIC_GPIO_REG_MODE_VALUE_SHIFT; + + return pmic_gpio_write(state, pad, PMIC_GPIO_REG_MODE_CTL, val); +} + +static void pmic_gpio_config_dbg_show(struct pinctrl_dev *pctldev, + struct seq_file *s, unsigned pin) +{ + struct pmic_gpio_state *state = pinctrl_dev_get_drvdata(pctldev); + struct pmic_gpio_pad *pad; + int ret, val; + + static const char *const biases[] = { + "pull-up 30uA", "pull-up 1.5uA", "pull-up 31.5uA", + "pull-up 1.5uA + 30uA boost", "pull-down 10uA", "no pull" + }; + static const char *const buffer_types[] = { + "push-pull", "open-drain", "open-source" + }; + static const char *const strengths[] = { + "no", "high", "medium", "low" + }; + + pad = pctldev->desc->pins[pin].drv_data; + + seq_printf(s, " gpio%-2d:", pin + PMIC_GPIO_PHYSICAL_OFFSET); + + val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_EN_CTL); + + if (val < 0 || !(val >> PMIC_GPIO_REG_MASTER_EN_SHIFT)) { + seq_puts(s, " ---"); + } else { + + if (!pad->input_enabled) { + ret = pmic_gpio_read(state, pad, PMIC_MPP_REG_RT_STS); + if (!ret) { + ret &= PMIC_MPP_REG_RT_STS_VAL_MASK; + pad->out_value = ret; + } + } + + seq_printf(s, " %-4s", pad->output_enabled ? "out" : "in"); + seq_printf(s, " %-7s", pmic_gpio_functions[pad->function]); + seq_printf(s, " vin-%d", pad->power_source); + seq_printf(s, " %-27s", biases[pad->pullup]); + seq_printf(s, " %-10s", buffer_types[pad->buffer_type]); + seq_printf(s, " %-4s", pad->out_value ? "high" : "low"); + seq_printf(s, " %-7s", strengths[pad->strength]); + } +} + +static const struct pinconf_ops pmic_gpio_pinconf_ops = { + .pin_config_group_get = pmic_gpio_config_get, + .pin_config_group_set = pmic_gpio_config_set, + .pin_config_group_dbg_show = pmic_gpio_config_dbg_show, +}; + +static int pmic_gpio_direction_input(struct gpio_chip *chip, unsigned pin) +{ + struct pmic_gpio_state *state = to_gpio_state(chip); + unsigned long config; + + config = pinconf_to_config_packed(PIN_CONFIG_INPUT_ENABLE, 1); + + return pmic_gpio_config_set(state->ctrl, pin, &config, 1); +} + +static int pmic_gpio_direction_output(struct gpio_chip *chip, + unsigned pin, int val) +{ + struct pmic_gpio_state *state = to_gpio_state(chip); + unsigned long config; + + config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, val); + + return pmic_gpio_config_set(state->ctrl, pin, &config, 1); +} + +static int pmic_gpio_get(struct gpio_chip *chip, unsigned pin) +{ + struct pmic_gpio_state *state = to_gpio_state(chip); + struct pmic_gpio_pad *pad; + int ret; + + pad = state->ctrl->desc->pins[pin].drv_data; + + if (!pad->is_enabled) + return -EINVAL; + + if (pad->input_enabled) { + ret = pmic_gpio_read(state, pad, PMIC_MPP_REG_RT_STS); + if (ret < 0) + return ret; + + pad->out_value = ret & PMIC_MPP_REG_RT_STS_VAL_MASK; + } + + return pad->out_value; +} + +static void pmic_gpio_set(struct gpio_chip *chip, unsigned pin, int value) +{ + struct pmic_gpio_state *state = to_gpio_state(chip); + unsigned long config; + + config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, value); + + pmic_gpio_config_set(state->ctrl, pin, &config, 1); +} + +static int pmic_gpio_request(struct gpio_chip *chip, unsigned base) +{ + return pinctrl_request_gpio(chip->base + base); +} + +static void pmic_gpio_free(struct gpio_chip *chip, unsigned base) +{ + pinctrl_free_gpio(chip->base + base); +} + +static int pmic_gpio_of_xlate(struct gpio_chip *chip, + const struct of_phandle_args *gpio_desc, + u32 *flags) +{ + if (chip->of_gpio_n_cells < 2) + return -EINVAL; + + if (flags) + *flags = gpio_desc->args[1]; + + return gpio_desc->args[0] - PMIC_GPIO_PHYSICAL_OFFSET; +} + +static int pmic_gpio_to_irq(struct gpio_chip *chip, unsigned pin) +{ + struct pmic_gpio_state *state = to_gpio_state(chip); + struct pmic_gpio_pad *pad; + + pad = state->ctrl->desc->pins[pin].drv_data; + + return pad->irq; +} + +static void pmic_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip) +{ + struct pmic_gpio_state *state = to_gpio_state(chip); + unsigned i; + + for (i = 0; i < chip->ngpio; i++) { + pmic_gpio_config_dbg_show(state->ctrl, s, i); + seq_puts(s, "\n"); + } +} + +static const struct gpio_chip pmic_gpio_gpio_template = { + .direction_input = pmic_gpio_direction_input, + .direction_output = pmic_gpio_direction_output, + .get = pmic_gpio_get, + .set = pmic_gpio_set, + .request = pmic_gpio_request, + .free = pmic_gpio_free, + .of_xlate = pmic_gpio_of_xlate, + .to_irq = pmic_gpio_to_irq, + .dbg_show = pmic_gpio_dbg_show, +}; + +static int pmic_gpio_populate(struct pmic_gpio_state *state, + struct pmic_gpio_pad *pad) +{ + int type, subtype, val, dir; + + type = pmic_gpio_read(state, pad, PMIC_GPIO_REG_TYPE); + if (type < 0) + return type; + + if (type != PMIC_GPIO_TYPE) { + dev_err(state->dev, "incorrect block type 0x%x at 0x%x\n", + type, pad->base); + return -ENODEV; + } + + subtype = pmic_gpio_read(state, pad, PMIC_GPIO_REG_SUBTYPE); + if (subtype < 0) + return subtype; + + switch (subtype) { + case PMIC_GPIO_SUBTYPE_GPIO_4CH: + pad->have_buffer = true; + case PMIC_GPIO_SUBTYPE_GPIOC_4CH: + pad->num_sources = 4; + break; + case PMIC_GPIO_SUBTYPE_GPIO_8CH: + pad->have_buffer = true; + case PMIC_GPIO_SUBTYPE_GPIOC_8CH: + pad->num_sources = 8; + break; + default: + dev_err(state->dev, "unknown GPIO type 0x%x\n", subtype); + return -ENODEV; + } + + val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_MODE_CTL); + if (val < 0) + return val; + + pad->out_value = val & PMIC_GPIO_REG_MODE_VALUE_SHIFT; + + dir = val >> PMIC_GPIO_REG_MODE_DIR_SHIFT; + dir &= PMIC_GPIO_REG_MODE_DIR_MASK; + switch (dir) { + case 0: + pad->input_enabled = true; + pad->output_enabled = false; + break; + case 1: + pad->input_enabled = false; + pad->output_enabled = true; + break; + case 2: + pad->input_enabled = true; + pad->output_enabled = true; + break; + default: + dev_err(state->dev, "unknown GPIO direction\n"); + return -ENODEV; + } + + pad->function = val >> PMIC_GPIO_REG_MODE_FUNCTION_SHIFT; + pad->function &= PMIC_GPIO_REG_MODE_FUNCTION_MASK; + + val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_VIN_CTL); + if (val < 0) + return val; + + pad->power_source = val >> PMIC_GPIO_REG_VIN_SHIFT; + pad->power_source &= PMIC_GPIO_REG_VIN_MASK; + + val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_PULL_CTL); + if (val < 0) + return val; + + pad->pullup = val >> PMIC_GPIO_REG_PULL_SHIFT; + pad->pullup &= PMIC_GPIO_REG_PULL_MASK; + + val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_OUT_CTL); + if (val < 0) + return val; + + pad->strength = val >> PMIC_GPIO_REG_OUT_STRENGTH_SHIFT; + pad->strength &= PMIC_GPIO_REG_OUT_STRENGTH_MASK; + + pad->buffer_type = val >> PMIC_GPIO_REG_OUT_TYPE_SHIFT; + pad->buffer_type &= PMIC_GPIO_REG_OUT_TYPE_MASK; + + /* Pin could be disabled with PIN_CONFIG_BIAS_HIGH_IMPEDANCE */ + pad->is_enabled = true; + return 0; +} + +static int pmic_gpio_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct pinctrl_pin_desc *pindesc; + struct pinctrl_desc *pctrldesc; + struct pmic_gpio_pad *pad, *pads; + struct pmic_gpio_state *state; + int ret, npins, i; + u32 res[2]; + + ret = of_property_read_u32_array(dev->of_node, "reg", res, 2); + if (ret < 0) { + dev_err(dev, "missing base address and/or range"); + return ret; + } + + npins = res[1] / PMIC_GPIO_ADDRESS_RANGE; + + if (!npins) + return -EINVAL; + + BUG_ON(npins > ARRAY_SIZE(pmic_gpio_groups)); + + state = devm_kzalloc(dev, sizeof(*state), GFP_KERNEL); + if (!state) + return -ENOMEM; + + platform_set_drvdata(pdev, state); + + state->dev = &pdev->dev; + state->map = dev_get_regmap(dev->parent, NULL); + + pindesc = devm_kcalloc(dev, npins, sizeof(*pindesc), GFP_KERNEL); + if (!pindesc) + return -ENOMEM; + + pads = devm_kcalloc(dev, npins, sizeof(*pads), GFP_KERNEL); + if (!pads) + return -ENOMEM; + + pctrldesc = devm_kzalloc(dev, sizeof(*pctrldesc), GFP_KERNEL); + if (!pctrldesc) + return -ENOMEM; + + pctrldesc->pctlops = &pmic_gpio_pinctrl_ops; + pctrldesc->pmxops = &pmic_gpio_pinmux_ops; + pctrldesc->confops = &pmic_gpio_pinconf_ops; + pctrldesc->owner = THIS_MODULE; + pctrldesc->name = dev_name(dev); + pctrldesc->pins = pindesc; + pctrldesc->npins = npins; + + for (i = 0; i < npins; i++, pindesc++) { + pad = &pads[i]; + pindesc->drv_data = pad; + pindesc->number = i; + pindesc->name = pmic_gpio_groups[i]; + + pad->irq = platform_get_irq(pdev, i); + if (pad->irq < 0) + return pad->irq; + + pad->base = res[0] + i * PMIC_GPIO_ADDRESS_RANGE; + + ret = pmic_gpio_populate(state, pad); + if (ret < 0) + return ret; + } + + state->chip = pmic_gpio_gpio_template; + state->chip.dev = dev; + state->chip.base = -1; + state->chip.ngpio = npins; + state->chip.label = dev_name(dev); + state->chip.of_gpio_n_cells = 2; + state->chip.can_sleep = false; + + state->ctrl = pinctrl_register(pctrldesc, dev, state); + if (!state->ctrl) + return -ENODEV; + + ret = gpiochip_add(&state->chip); + if (ret) { + dev_err(state->dev, "can't add gpio chip\n"); + goto err_chip; + } + + ret = gpiochip_add_pin_range(&state->chip, dev_name(dev), 0, 0, npins); + if (ret) { + dev_err(dev, "failed to add pin range\n"); + goto err_range; + } + + return 0; + +err_range: + gpiochip_remove(&state->chip); +err_chip: + pinctrl_unregister(state->ctrl); + return ret; +} + +static int pmic_gpio_remove(struct platform_device *pdev) +{ + struct pmic_gpio_state *state = platform_get_drvdata(pdev); + int ret; + + ret = gpiochip_remove(&state->chip); + if (ret < 0) + return ret; + + pinctrl_unregister(state->ctrl); + return 0; +} + +static const struct of_device_id pmic_gpio_of_match[] = { + { .compatible = "qcom,pm8941-gpio" }, /* 36 GPIO's */ + { .compatible = "qcom,pma8084-gpio" }, /* 22 GPIO's */ + { }, +}; + +MODULE_DEVICE_TABLE(of, pmic_gpio_of_match); + +static struct platform_driver pmic_gpio_driver = { + .driver = { + .name = "qcom-spmi-gpio", + .of_match_table = pmic_gpio_of_match, + }, + .probe = pmic_gpio_probe, + .remove = pmic_gpio_remove, +}; + +module_platform_driver(pmic_gpio_driver); + +MODULE_AUTHOR("Ivan T. Ivanov "); +MODULE_DESCRIPTION("Qualcomm SPMI PMIC GPIO pin control driver"); +MODULE_ALIAS("platform:qcom-spmi-gpio"); +MODULE_LICENSE("GPL v2"); -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/