Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1753486AbaKDKyg (ORCPT ); Tue, 4 Nov 2014 05:54:36 -0500 Received: from mx08-00178001.pphosted.com ([91.207.212.93]:40991 "EHLO mx08-00178001.pphosted.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752676AbaKDKxO (ORCPT ); Tue, 4 Nov 2014 05:53:14 -0500 From: Gabriel FERNANDEZ To: Rob Herring , Pawel Moll , Mark Rutland , Ian Campbell , Kumar Gala , Srinivas Kandagatla , Maxime Coquelin , Patrice Chotard , Russell King , Kishon Vijay Abraham I , Grant Likely Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org, kernel@stlinux.com, Lee Jones , Gabriel Fernandez , alexandre torgue , Giuseppe Cavallaro Subject: [PATCH v5 1/8] phy: miphy28lp: Add Device Tree bindings for the MiPHY28lp Date: Tue, 4 Nov 2014 11:51:17 +0100 Message-Id: <1415098284-11182-2-git-send-email-gabriel.fernandez@linaro.org> X-Mailer: git-send-email 1.9.1 In-Reply-To: <1415098284-11182-1-git-send-email-gabriel.fernandez@linaro.org> References: <1415098284-11182-1-git-send-email-gabriel.fernandez@linaro.org> X-Proofpoint-Virus-Version: vendor=fsecure engine=2.50.10432:5.12.52,1.0.28,0.0.0000 definitions=2014-11-04_05:2014-11-03,2014-11-04,1970-01-01 signatures=0 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org The MiPHY28lp is a Generic PHY which can serve various SATA or PCIe or USB3 devices. Signed-off-by: alexandre torgue Signed-off-by: Giuseppe Cavallaro Signed-off-by: Gabriel Fernandez --- .../devicetree/bindings/phy/phy-miphy28lp.txt | 126 +++++++++++++++++++++ 1 file changed, 126 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/phy-miphy28lp.txt diff --git a/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt new file mode 100644 index 0000000..b7c13ad --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt @@ -0,0 +1,126 @@ +STMicroelectronics STi MIPHY28LP PHY binding +============================================ + +This binding describes a miphy device that is used to control PHY hardware +for SATA, PCIe or USB3. + +Required properties (controller (parent) node): +- compatible : Should be "st,miphy28lp-phy". +- st,syscfg : Should be a phandle of the system configuration register group + which contain the SATA, PCIe or USB3 mode setting bits. + +Required nodes : A sub-node is required for each channel the controller + provides. Address range information including the usual + 'reg' and 'reg-names' properties are used inside these + nodes to describe the controller's topology. These nodes + are translated by the driver's .xlate() function. + +Required properties (port (child) node): +- #phy-cells : Should be 1 (See second example) + Cell after port phandle is device type from: + - PHY_TYPE_SATA + - PHY_TYPE_PCI + - PHY_TYPE_USB3 +- reg : Address and length of the register set for the device. +- reg-names : The names of the register addresses corresponding to the registers + filled in "reg". It can also contain the offset of the system configuration + registers used as glue-logic to setup the device for SATA/PCIe or USB3 + devices. +- resets : phandle to the parent reset controller. +- reset-names : Associated name must be "miphy-sw-rst". + +Optional properties (port (child) node): +- st,osc-rdy : to check the MIPHY0_OSC_RDY status in the glue-logic. This + is not available in all the MiPHY. For example, for STiH407, only the + MiPHY0 has this bit. +- st,osc-force-ext : to select the external oscillator. This can change from + different MiPHY inside the same SoC. +- st,sata_gen : to select which SATA_SPDMODE has to be set in the SATA system config + register. +- st,px_rx_pol_inv : to invert polarity of RXn/RXp (respectively negative line and positive + line). + +example: + + miphy28lp_phy: miphy28lp@9b22000 { + compatible = "st,miphy28lp-phy"; + st,syscfg = <&syscfg_core>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + phy_port0: port@9b22000 { + reg = <0x9b22000 0xff>, + <0x9b09000 0xff>, + <0x9b04000 0xff>, + <0x114 0x4>, /* sysctrl MiPHY cntrl */ + <0x818 0x4>, /* sysctrl MiPHY status*/ + <0xe0 0x4>, /* sysctrl PCIe */ + <0xec 0x4>; /* sysctrl SATA */ + reg-names = "sata-up", + "pcie-up", + "pipew", + "miphy-ctrl-glue", + "miphy-status-glue", + "pcie-glue", + "sata-glue"; + #phy-cells = <1>; + st,osc-rdy; + reset-names = "miphy-sw-rst"; + resets = <&softreset STIH407_MIPHY0_SOFTRESET>; + }; + + phy_port1: port@9b2a000 { + reg = <0x9b2a000 0xff>, + <0x9b19000 0xff>, + <0x9b14000 0xff>, + <0x118 0x4>, + <0x81c 0x4>, + <0xe4 0x4>, + <0xf0 0x4>; + reg-names = "sata-up", + "pcie-up", + "pipew", + "miphy-ctrl-glue", + "miphy-status-glue", + "pcie-glue", + "sata-glue"; + #phy-cells = <1>; + st,osc-force-ext; + reset-names = "miphy-sw-rst"; + resets = <&softreset STIH407_MIPHY1_SOFTRESET>; + }; + + phy_port2: port@8f95000 { + reg = <0x8f95000 0xff>, + <0x8f90000 0xff>, + <0x11c 0x4>, + <0x820 0x4>; + reg-names = "pipew", + "usb3-up", + "miphy-ctrl-glue", + "miphy-status-glue"; + #phy-cells = <1>; + reset-names = "miphy-sw-rst"; + resets = <&softreset STIH407_MIPHY2_SOFTRESET>; + }; + }; + + +Specifying phy control of devices +================================= + +Device nodes should specify the configuration required in their "phys" +property, containing a phandle to the miphy device node and an index +specifying which configuration to use, as described in phy-bindings.txt. + +example: + sata0: sata@9b20000 { + ... + phys = <&phy_port0 PHY_TYPE_SATA>; + ... + }; + +Macro definitions for the supported miphy configuration can be found in: + +include/dt-bindings/phy/phy-miphy28lp.h -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/