Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1751278AbaKFOJp (ORCPT ); Thu, 6 Nov 2014 09:09:45 -0500 Received: from opensource.wolfsonmicro.com ([80.75.67.52]:42330 "EHLO opensource.wolfsonmicro.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1750828AbaKFOJm (ORCPT ); Thu, 6 Nov 2014 09:09:42 -0500 Date: Thu, 6 Nov 2014 14:09:40 +0000 From: Charles Keepax To: "Stam, Michel [FINT]" Cc: Riku Voipio , freddy@asix.com.tw, davem@davemloft.net, linux-usb@vger.kernel.org, netdev@vger.kernel.org, linux-kernel@vger.kernel.org, linux-samsung-soc@vger.kernel.org Subject: Re: "asix: Don't reset PHY on if_up for ASIX 88772" breaks net onarndale platform Message-ID: <20141106140940.GW23178@opensource.wolfsonmicro.com> References: <20141104200914.GN23178@opensource.wolfsonmicro.com> <20141105150258.GR23178@opensource.wolfsonmicro.com> <20141106090651.GA19109@afflict.kos.to> <20141106100104.GS23178@opensource.wolfsonmicro.com> <20141106120416.GA20162@afflict.kos.to> <20141106124653.GV23178@opensource.wolfsonmicro.com> MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Disposition: inline In-Reply-To: User-Agent: Mutt/1.5.17+20080114 (2008-01-14) Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org On Thu, Nov 06, 2014 at 03:01:56PM +0100, Stam, Michel [FINT] wrote: > Hello Charles and Riku, > > I've quickly tested this on a 3.10 kernel i had around; > I enabled CONFIG_PM, CONFIG_PM_RUNTIME, CONFIG_PM_AUTOSLEEP, > CONFIG_SUSPEND, CONFIG_SUSPEND_FREEZER, CONFIG_FREEZER in the kernel (by > default they are disabled for our setup, I enabled anything regarded to > runtime powermanagement to be sure I would trigger suspend/resume). > > Then: > cd /sys/bus/usb/devices/1-2/power > echo auto > control > echo 1 > autosuspend > echo 0 > autosuspend_delay_ms > echo enabled > wakeup > > # make sure there's no processes routing traffic over the eth1 interface > > ifconfig eth1 down > sleep 4 # sleep some arbitrary long time > ifconfig eth1 up > > check dmesg; it will reset back to 100 Mbps/full duplex. > > This confirms that the suspend / resume does not work well. So long as > the suspend is not triggered, it does seem to work, though. I cannot say > whether the original issue that triggered this is still around; the ASIX > chip setup we use is soldered to the PCB and hooked up to a fixed device > on-board. > I also tried to ping the device on the other side of the ASIX chip after > the suspend/resume cycle, I could not ping it. I cannot conclusively say > that this is due to the ASIX driver, as the device on the other side > does not like switching PHY speeds (it may go into a non-responsive > state). It is for this reason that we run it at half duplex/ 10Mbps at > all times. > > As said; we are not using this kind of power management, so it does not > raise any issues for us. I am merely pointing out that this may need > work (in the future?). Cool thanks for checking this I will make a note in the commit message that suspend/resume might need some more work. Thanks, Charles -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/