Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S933092AbaLJT5G (ORCPT ); Wed, 10 Dec 2014 14:57:06 -0500 Received: from mail-gw3-out.broadcom.com ([216.31.210.64]:60794 "EHLO mail-gw3-out.broadcom.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S932600AbaLJT5E (ORCPT ); Wed, 10 Dec 2014 14:57:04 -0500 X-IronPort-AV: E=Sophos;i="5.07,553,1413270000"; d="scan'208";a="52600527" Message-ID: <5488A58C.6010102@broadcom.com> Date: Wed, 10 Dec 2014 11:57:00 -0800 From: Jonathan Richardson User-Agent: Mozilla/5.0 (X11; Linux i686; rv:17.0) Gecko/17.0 Thunderbird/17.0 MIME-Version: 1.0 To: Tim Kryger CC: Arun Ramamurthy , Scott Branden , Thierry Reding , Ray Jui , Arun Ramamurthy , , , "Linux Kernel Mailing List" Subject: Re: [PATCH v2 1/4] pwm: kona: Remove setting default smooth type and polarity for all channels References: <1416944441-12066-1-git-send-email-sbranden@broadcom.com> <1416944441-12066-2-git-send-email-sbranden@broadcom.com> <5479097B.6020108@broadcom.com> <54791F30.3050306@broadcom.com> <5480C286.6000405@broadcom.com> In-Reply-To: Content-Type: text/plain; charset="UTF-8" Content-Transfer-Encoding: 7bit Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org On 14-12-06 03:13 PM, Tim Kryger wrote: > On Thu, Dec 4, 2014 at 12:22 PM, Jonathan Richardson > wrote: >> Hi Tim, >> >> I'm going to take over this submission because I made the changes to the >> driver. Arun was filling in for me while I was on leave. Now I'm back >> and I think I can help clarify why these changes were made. A summary >> for all the changes should help. >> >> There were two problems. First was a problem caused by setting the >> polarity in probe. It caused the speaker to click when the polarity was >> set so we took that out as it didn't seem to serve any useful purpose >> that I could see. The polarity changes should be made in the polarity >> callback. > > Please provide more details about your configuration. > > Are you using the pwm-beeper driver with a piezo? Probably, but I don't know. We don't care about it and aren't using it which underscores why we don't want to initialize pwm channels we aren't using. > > After a reset, all PWM output will be low until the PWM clock is > enabled at which point it will be constant high. Are you confident > that this transition is not responsible for the click you are hearing? > >> The second and bigger problem was the smooth type sequence. If it isn't >> done according to the spec then one in ten or twenty times you won't >> even get a signal when it's enabled. Following the correct sequence with >> the 400 ns delays solves this problem. > > Would the following minor change be sufficient to fix the issue? Not quite but hopefully I can send a patch soon for your review. > > diff --git a/drivers/pwm/pwm-bcm-kona.c b/drivers/pwm/pwm-bcm-kona.c > index 02bc048..c537efd 100644 > --- a/drivers/pwm/pwm-bcm-kona.c > +++ b/drivers/pwm/pwm-bcm-kona.c > @@ -85,6 +85,9 @@ static void kona_pwmc_apply_settings(struct kona_pwmc *kp, uns > value &= ~(1 << PWM_CONTROL_TRIGGER_SHIFT(chan)); > writel(value, kp->base + PWM_CONTROL_OFFSET); > > + ndelay(400); > + > /* Set trigger bit and clear smooth bit to apply new settings */ > value &= ~(1 << PWM_CONTROL_SMOOTH_SHIFT(chan)); > value |= 1 << PWM_CONTROL_TRIGGER_SHIFT(chan); > >> >> Additionally, by not following the sequence you won't get a smooth >> transition. You'll get a change in the settings (duty cycle, period) but >> may get a non smooth transition. So it's important to follow the spec >> here. We don't want non-smooth transitions. > > Please provide your rationale for requiring smooth transitions. The rationale is we don't want to give customers a bad experience when we can provide them with a better one. The driver attempts to use smooth transitions already but due to the quirks in the procedure which were sent out previously it doesn't quite work as intended. When changing the waveform we want to always have smooth transitions. There are unused pwm channels that vendors can hook up whatever they want. Thanks, Jon > > Thanks, > Tim Kryger > -- > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/ > -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/