Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1752547AbaLSQWs (ORCPT ); Fri, 19 Dec 2014 11:22:48 -0500 Received: from ext3.cumulusnetworks.com ([198.211.106.187]:49660 "EHLO ext3.cumulusnetworks.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751218AbaLSQWq (ORCPT ); Fri, 19 Dec 2014 11:22:46 -0500 Message-ID: <549450D0.8030805@cumulusnetworks.com> Date: Fri, 19 Dec 2014 08:22:40 -0800 From: Roopa Prabhu User-Agent: Mozilla/5.0 (Macintosh; Intel Mac OS X 10.9; rv:17.0) Gecko/20130801 Thunderbird/17.0.8 MIME-Version: 1.0 To: Jiri Pirko CC: B Viswanath , "Samudrala, Sridhar" , John Fastabend , "Varlese, Marco" , "netdev@vger.kernel.org" , Thomas Graf , "sfeldma@gmail.com" , "linux-kernel@vger.kernel.org" Subject: Re: [RFC PATCH net-next v2 1/1] net: Support for switch port configuration References: <54931969.7040209@cumulusnetworks.com> <5493293A.2000802@intel.com> <54935E28.8050602@cumulusnetworks.com> <549362A5.3000808@intel.com> <549367CC.2080307@cumulusnetworks.com> <20141219082754.GE1848@nanopsycho.orion> <20141219092308.GF1848@nanopsycho.orion> <20141219095512.GH1848@nanopsycho.orion> In-Reply-To: <20141219095512.GH1848@nanopsycho.orion> Content-Type: text/plain; charset=ISO-8859-1; format=flowed Content-Transfer-Encoding: 7bit Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org On 12/19/14, 1:55 AM, Jiri Pirko wrote: > Fri, Dec 19, 2014 at 10:35:27AM CET, marichika4@gmail.com wrote: >> On 19 December 2014 at 14:53, Jiri Pirko wrote: >>> Fri, Dec 19, 2014 at 10:01:46AM CET, marichika4@gmail.com wrote: >>>> On 19 December 2014 at 13:57, Jiri Pirko wrote: >>>>> Fri, Dec 19, 2014 at 06:14:57AM CET, marichika4@gmail.com wrote: >>>>>> On 19 December 2014 at 05:18, Roopa Prabhu wrote: >>>>>>> On 12/18/14, 3:26 PM, Samudrala, Sridhar wrote: >>>> >>>>>>>> >>>>>>>> We also need an interface to set per-switch attributes. Can this work? >>>>>>>> bridge link set dev sw0 sw_attr bcast_flooding 1 master >>>>>>>> where sw0 is a bridge representing the hardware switch. >>>>>>> >>>>>>> Not today. We discussed this @ LPC, and one way to do this would be to have >>>>>>> a device >>>>>>> representing the switch asic. This is in the works. >>>>>> >>>>>> Can I assume that on platforms which house more than one asic (say >>>>>> two 24 port asics, interconnected via a 10G link or equivalent, to get >>>>>> a 48 port 'switch') , the 'rocker' driver (or similar) should expose >>>>>> them as a single set of ports, and not as two 'switch ports' ? >>>>> Well that really depends on particular implementation and drivers. If you >>>>> have 2 pci-e devices, I think you should expose them as 2 entities. For >>>>> sure, you can have the driver to do the masking for you. I don't believe >>>>> that is correct though. >>>>> >>>> In a platform that houses two asic chips, IMO, the user is still >>>> expected to manage the router as a single entity. The configuration >>>> being applied on both asic devices need to be matching if not >>>> identical, and may not be conflicting. The FDB is to be synchronized >>>> so that (offloaded) switching can happen across the asics. Some of >>>> this stuff is asic specific anyway. Another example is that of the >>>> learning. The (hardware) learning can't be enabled on one asic, while >>>> being disabled on another one. The general use cases I have seen are >>>> all involving managing the 'router' as a single entity. That the >>>> 'router' is implemented with two asics instead of a single asic (with >>>> more ports) is to be treated as an implementation detail. This is the >>>> usual router management method that exists today. >>>> >>>> I hope I make sense. >>>> >>>> So I am trying to figure out what this single entity that will be used >>> >from a user perspective. It can be a bridge, but our bridges are more >>>> 802.1q bridges. We can use the 'self' mode, but then it means that it >>>> should reflect the entire port count, and not just an asic. >>>> >>>> So I was trying to deduce that in our switchdevice model, the best bet >>>> would be to leave the unification to the driver (i.e., to project the >>>> multiple physical asics as a single virtual switch device). Thist >>> Is it possible to have the asic as just single one? Or is it possible to >>> connect asics being multiple chips maybe from multiple vendors together? >> I didn't understand the first question. Some times, it is possible to > I ment that there is a design with just a single asic of this type, > instead of a pair. > >> have a single asic replace two, but its a cost factor, and others that >> are involved. >> >> AFAIK, the answer to the second question is a No. Two asics from >> different vendors may not be connected together. The interconnect >> tends to be proprietary. > Okay. In that case, it might make sense to mask it on driver level. > > >>> I believe that answer is "yes" in both cases. Making two separate asics >>> to appear as one for user is not correct in my opinion. Driver should >>> not do such masking. It is unclean, unextendable. >>> >> I am only looking for a single management entity. I am not thinking it >> needs to be at driver level. I am not sure of any other option apart > >from creating a 'switchdev' that Roopa was mentioning. > > Well the thing is there is a common desire to make the offloading as > transparent as possible. For example, have 4 ports of same switch and > put them into br0. Just like that, without need to do anything else > than you would do when bridging ordinary NICs. Introducing some > "management entity" would break this approach. > I don't think having a switchdevice breaks this approach. A software bridge is not a 1-1 mapping with the asic in all cases. When its a vlan filtering bridge, yes, it is (In which case all switch global l2 non-port specific attributes can be applied to the bridge). The switch asic can do l2 and l3 too. For a bridge, the switch asic is just accelerating l2. And a switch asic is also capable of l3, acls. A switch device (whether accessible to userspace or not) may become necessary (as discussed in other threads) where you cannot resolve a kernel object to a switch port (Global acl rules, unresolved route nexthops etc). -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/