Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1752136AbaLXMgx (ORCPT ); Wed, 24 Dec 2014 07:36:53 -0500 Received: from mail-lb0-f178.google.com ([209.85.217.178]:60285 "EHLO mail-lb0-f178.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751751AbaLXMgu (ORCPT ); Wed, 24 Dec 2014 07:36:50 -0500 MIME-Version: 1.0 In-Reply-To: <20141223155311.GA5997@vivalin-002> References: <20141223154654.GB6460@vivalin-002> <20141223155311.GA5997@vivalin-002> From: Olivier Sobrie Date: Wed, 24 Dec 2014 13:36:27 +0100 X-Google-Sender-Auth: 3gCzUTwfx95nAsb1LEMHZ90OeqE Message-ID: Subject: Re: [PATCH] can: kvaser_usb: Add support for the Usbcan-II family To: "Ahmed S. Darwish" Cc: Oliver Hartkopp , Wolfgang Grandegger , Marc Kleine-Budde , "David S. Miller" , Paul Gortmaker , Linux-CAN , netdev , LKML Content-Type: text/plain; charset=UTF-8 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Hello Ahmed, On Tue, Dec 23, 2014 at 05:53:11PM +0200, Ahmed S. Darwish wrote: > From: Ahmed S. Darwish > > CAN to USB interfaces sold by the Swedish manufacturer Kvaser are > divided into two major families: 'Leaf', and 'UsbcanII'. From an > Operating System perspective, the firmware of both families behave > in a not too drastically different fashion. > > This patch adds support for the UsbcanII family of devices to the > current Kvaser Leaf-only driver. > > CAN frames sending, receiving, and error handling paths has been > tested using the dual-channel "Kvaser USBcan II HS/LS" dongle. It > should also work nicely with other products in the same category. Good, thank you :-) I'll try to test the patch during the next week-end. Small remarks below. > > Signed-off-by: Ahmed S. Darwish > --- > drivers/net/can/usb/kvaser_usb.c | 630 +++++++++++++++++++++++++++++++-------- > 1 file changed, 505 insertions(+), 125 deletions(-) > > (Generated over 3.19.0-rc1 + generic bugfix at > can-kvaser_usb-Don-t-free-packets-when-tight-on-URBs.patch) > > diff --git a/drivers/net/can/usb/kvaser_usb.c b/drivers/net/can/usb/kvaser_usb.c > index 34c35d8..e7076da 100644 > --- a/drivers/net/can/usb/kvaser_usb.c > +++ b/drivers/net/can/usb/kvaser_usb.c > @@ -6,12 +6,15 @@ > * Parts of this driver are based on the following: > * - Kvaser linux leaf driver (version 4.78) > * - CAN driver for esd CAN-USB/2 > + * - Kvaser linux usbcanII driver (version 5.3) > * > * Copyright (C) 2002-2006 KVASER AB, Sweden. All rights reserved. > * Copyright (C) 2010 Matthias Fuchs , esd gmbh > * Copyright (C) 2012 Olivier Sobrie > + * Copyright (C) 2014 Valeo Corporation > */ > > +#include > #include > #include > #include > @@ -21,6 +24,18 @@ > #include > #include > > +#define MAX(a, b) ((a) > (b) ? (a) : (b)) There is a max(a, b) macro in . > + > +/* > + * Kvaser USB CAN dongles are divided into two major families: > + * - Leaf: Based on Renesas M32C, running firmware labeled as 'filo' > + * - UsbcanII: Based on Renesas M16C, running firmware labeled as 'helios' > + */ > +enum kvaser_usb_family { > + KVASER_LEAF, > + KVASER_USBCAN, > +}; > + > #define MAX_TX_URBS 16 > #define MAX_RX_URBS 4 > #define START_TIMEOUT 1000 /* msecs */ > @@ -29,9 +44,12 @@ > #define USB_RECV_TIMEOUT 1000 /* msecs */ > #define RX_BUFFER_SIZE 3072 > #define CAN_USB_CLOCK 8000000 > -#define MAX_NET_DEVICES 3 > +#define LEAF_MAX_NET_DEVICES 3 > +#define USBCAN_MAX_NET_DEVICES 2 > +#define MAX_NET_DEVICES MAX(LEAF_MAX_NET_DEVICES, \ > + USBCAN_MAX_NET_DEVICES) > > -/* Kvaser USB devices */ > +/* Leaf USB devices */ > #define KVASER_VENDOR_ID 0x0bfd > #define USB_LEAF_DEVEL_PRODUCT_ID 10 > #define USB_LEAF_LITE_PRODUCT_ID 11 > @@ -55,6 +73,16 @@ > #define USB_CAN_R_PRODUCT_ID 39 > #define USB_LEAF_LITE_V2_PRODUCT_ID 288 > #define USB_MINI_PCIE_HS_PRODUCT_ID 289 > +#define LEAF_PRODUCT_ID(id) (id >= USB_LEAF_DEVEL_PRODUCT_ID && \ > + id <= USB_MINI_PCIE_HS_PRODUCT_ID) > + > +/* USBCANII devices */ > +#define USB_USBCAN_REVB_PRODUCT_ID 2 > +#define USB_VCI2_PRODUCT_ID 3 > +#define USB_USBCAN2_PRODUCT_ID 4 > +#define USB_MEMORATOR_PRODUCT_ID 5 > +#define USBCAN_PRODUCT_ID(id) (id >= USB_USBCAN_REVB_PRODUCT_ID && \ > + id <= USB_MEMORATOR_PRODUCT_ID) > > /* USB devices features */ > #define KVASER_HAS_SILENT_MODE BIT(0) > @@ -73,7 +101,7 @@ > #define MSG_FLAG_TX_ACK BIT(6) > #define MSG_FLAG_TX_REQUEST BIT(7) > > -/* Can states */ > +/* Can states (M16C CxSTRH register) */ > #define M16C_STATE_BUS_RESET BIT(0) > #define M16C_STATE_BUS_ERROR BIT(4) > #define M16C_STATE_BUS_PASSIVE BIT(5) > @@ -98,7 +126,13 @@ > #define CMD_START_CHIP_REPLY 27 > #define CMD_STOP_CHIP 28 > #define CMD_STOP_CHIP_REPLY 29 > -#define CMD_GET_CARD_INFO2 32 > +#define CMD_READ_CLOCK 30 > +#define CMD_READ_CLOCK_REPLY 31 > + > +#define LEAF_CMD_GET_CARD_INFO2 32 > +#define USBCAN_CMD_RESET_CLOCK 32 > +#define USBCAN_CMD_CLOCK_OVERFLOW_EVENT 33 > + > #define CMD_GET_CARD_INFO 34 > #define CMD_GET_CARD_INFO_REPLY 35 > #define CMD_GET_SOFTWARE_INFO 38 > @@ -108,8 +142,9 @@ > #define CMD_RESET_ERROR_COUNTER 49 > #define CMD_TX_ACKNOWLEDGE 50 > #define CMD_CAN_ERROR_EVENT 51 > -#define CMD_USB_THROTTLE 77 > -#define CMD_LOG_MESSAGE 106 > + > +#define LEAF_CMD_USB_THROTTLE 77 > +#define LEAF_CMD_LOG_MESSAGE 106 > > /* error factors */ > #define M16C_EF_ACKE BIT(0) > @@ -121,6 +156,13 @@ > #define M16C_EF_RCVE BIT(6) > #define M16C_EF_TRE BIT(7) > > +/* Only Leaf-based devices can report M16C error factors, > + * thus define our own error status flags for USBCAN */ > +#define USBCAN_ERROR_STATE_NONE 0 > +#define USBCAN_ERROR_STATE_TX_ERROR BIT(0) > +#define USBCAN_ERROR_STATE_RX_ERROR BIT(1) > +#define USBCAN_ERROR_STATE_BUSERROR BIT(2) > + > /* bittiming parameters */ > #define KVASER_USB_TSEG1_MIN 1 > #define KVASER_USB_TSEG1_MAX 16 > @@ -137,7 +179,7 @@ > #define KVASER_CTRL_MODE_SELFRECEPTION 3 > #define KVASER_CTRL_MODE_OFF 4 > > -/* log message */ > +/* Extended CAN identifier flag */ > #define KVASER_EXTENDED_FRAME BIT(31) > > struct kvaser_msg_simple { > @@ -148,30 +190,55 @@ struct kvaser_msg_simple { > struct kvaser_msg_cardinfo { > u8 tid; > u8 nchannels; > - __le32 serial_number; > - __le32 padding; > + union { > + struct { > + __le32 serial_number; > + __le32 padding; > + } __packed leaf0; > + struct { > + __le32 serial_number_low; > + __le32 serial_number_high; > + } __packed usbcan0; > + } __packed; > __le32 clock_resolution; > __le32 mfgdate; > u8 ean[8]; > u8 hw_revision; > - u8 usb_hs_mode; > - __le16 padding2; > + union { > + struct { > + u8 usb_hs_mode; > + } __packed leaf1; > + struct { > + u8 padding; > + } __packed usbcan1; > + } __packed; > + __le16 padding; > } __packed; > > struct kvaser_msg_cardinfo2 { > u8 tid; > - u8 channel; > + u8 reserved; > u8 pcb_id[24]; > __le32 oem_unlock_code; > } __packed; > > -struct kvaser_msg_softinfo { > +struct leaf_msg_softinfo { > u8 tid; > - u8 channel; > + u8 padding0; > __le32 sw_options; > __le32 fw_version; > __le16 max_outstanding_tx; > - __le16 padding[9]; > + __le16 padding1[9]; > +} __packed; > + > +struct usbcan_msg_softinfo { > + u8 tid; > + u8 fw_name[5]; > + __le16 max_outstanding_tx; > + u8 padding[6]; > + __le32 fw_version; > + __le16 checksum; > + __le16 sw_options; > } __packed; > > struct kvaser_msg_busparams { > @@ -188,36 +255,86 @@ struct kvaser_msg_tx_can { > u8 channel; > u8 tid; > u8 msg[14]; > - u8 padding; > - u8 flags; > + union { > + struct { > + u8 padding; > + u8 flags; > + } __packed leaf; > + struct { > + u8 flags; > + u8 padding; > + } __packed usbcan; > + } __packed; > +} __packed; > + > +struct kvaser_msg_rx_can_header { > + u8 channel; > + u8 flag; > } __packed; > > -struct kvaser_msg_rx_can { > +struct leaf_msg_rx_can { > u8 channel; > u8 flag; > + > __le16 time[3]; > u8 msg[14]; > } __packed; > > -struct kvaser_msg_chip_state_event { > +struct usbcan_msg_rx_can { > + u8 channel; > + u8 flag; > + > + u8 msg[14]; > + __le16 time; > +} __packed; > + > +struct leaf_msg_chip_state_event { > u8 tid; > u8 channel; > + > __le16 time[3]; > u8 tx_errors_count; > u8 rx_errors_count; > + > u8 status; > u8 padding[3]; > } __packed; > > -struct kvaser_msg_tx_acknowledge { > +struct usbcan_msg_chip_state_event { > + u8 tid; > + u8 channel; > + > + u8 tx_errors_count; > + u8 rx_errors_count; > + __le16 time; > + > + u8 status; > + u8 padding[3]; > +} __packed; > + > +struct kvaser_msg_tx_acknowledge_header { > + u8 channel; > + u8 tid; > +}; > + > +struct leaf_msg_tx_acknowledge { > u8 channel; > u8 tid; > + > __le16 time[3]; > u8 flags; > u8 time_offset; > } __packed; > > -struct kvaser_msg_error_event { > +struct usbcan_msg_tx_acknowledge { > + u8 channel; > + u8 tid; > + > + __le16 time; > + __le16 padding; > +} __packed; > + > +struct leaf_msg_error_event { > u8 tid; > u8 flags; > __le16 time[3]; > @@ -229,6 +346,18 @@ struct kvaser_msg_error_event { > u8 error_factor; > } __packed; > > +struct usbcan_msg_error_event { > + u8 tid; > + u8 padding; > + u8 tx_errors_count_ch0; > + u8 rx_errors_count_ch0; > + u8 tx_errors_count_ch1; > + u8 rx_errors_count_ch1; > + u8 status_ch0; > + u8 status_ch1; > + __le16 time; > +} __packed; > + > struct kvaser_msg_ctrl_mode { > u8 tid; > u8 channel; > @@ -243,7 +372,7 @@ struct kvaser_msg_flush_queue { > u8 padding[3]; > } __packed; > > -struct kvaser_msg_log_message { > +struct leaf_msg_log_message { > u8 channel; > u8 flags; > __le16 time[3]; > @@ -260,19 +389,49 @@ struct kvaser_msg { > struct kvaser_msg_simple simple; > struct kvaser_msg_cardinfo cardinfo; > struct kvaser_msg_cardinfo2 cardinfo2; > - struct kvaser_msg_softinfo softinfo; > struct kvaser_msg_busparams busparams; > + > + struct kvaser_msg_rx_can_header rx_can_header; > + struct kvaser_msg_tx_acknowledge_header tx_acknowledge_header; > + > + union { > + struct leaf_msg_softinfo softinfo; > + struct leaf_msg_rx_can rx_can; > + struct leaf_msg_chip_state_event chip_state_event; > + struct leaf_msg_tx_acknowledge tx_acknowledge; > + struct leaf_msg_error_event error_event; > + struct leaf_msg_log_message log_message; > + } __packed leaf; > + > + union { > + struct usbcan_msg_softinfo softinfo; > + struct usbcan_msg_rx_can rx_can; > + struct usbcan_msg_chip_state_event chip_state_event; > + struct usbcan_msg_tx_acknowledge tx_acknowledge; > + struct usbcan_msg_error_event error_event; > + } __packed usbcan; > + > struct kvaser_msg_tx_can tx_can; > - struct kvaser_msg_rx_can rx_can; > - struct kvaser_msg_chip_state_event chip_state_event; > - struct kvaser_msg_tx_acknowledge tx_acknowledge; > - struct kvaser_msg_error_event error_event; > struct kvaser_msg_ctrl_mode ctrl_mode; > struct kvaser_msg_flush_queue flush_queue; > - struct kvaser_msg_log_message log_message; > } u; > } __packed; > > +/* Leaf/USBCAN-agnostic summary of an error event. > + * No M16C error factors for USBCAN-based devices. */ > +struct kvaser_error_summary { > + u8 channel, status, txerr, rxerr; > + union { > + struct { > + u8 error_factor; > + } leaf; > + struct { > + u8 other_ch_status; > + u8 error_state; > + } usbcan; > + }; > +}; > + > struct kvaser_usb_tx_urb_context { > struct kvaser_usb_net_priv *priv; > u32 echo_index; > @@ -288,6 +447,8 @@ struct kvaser_usb { > > u32 fw_version; > unsigned int nchannels; > + enum kvaser_usb_family family; > + unsigned int max_channels; > > bool rxinitdone; > void *rxbuf[MAX_RX_URBS]; > @@ -311,6 +472,7 @@ struct kvaser_usb_net_priv { > }; > > static const struct usb_device_id kvaser_usb_table[] = { > + /* Leaf family IDs */ > { USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_DEVEL_PRODUCT_ID) }, > { USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LITE_PRODUCT_ID) }, > { USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_PRO_PRODUCT_ID), > @@ -360,6 +522,17 @@ static const struct usb_device_id kvaser_usb_table[] = { > .driver_info = KVASER_HAS_TXRX_ERRORS }, > { USB_DEVICE(KVASER_VENDOR_ID, USB_LEAF_LITE_V2_PRODUCT_ID) }, > { USB_DEVICE(KVASER_VENDOR_ID, USB_MINI_PCIE_HS_PRODUCT_ID) }, > + > + /* USBCANII family IDs */ > + { USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN2_PRODUCT_ID), > + .driver_info = KVASER_HAS_TXRX_ERRORS }, > + { USB_DEVICE(KVASER_VENDOR_ID, USB_USBCAN_REVB_PRODUCT_ID), > + .driver_info = KVASER_HAS_TXRX_ERRORS }, > + { USB_DEVICE(KVASER_VENDOR_ID, USB_MEMORATOR_PRODUCT_ID), > + .driver_info = KVASER_HAS_TXRX_ERRORS }, > + { USB_DEVICE(KVASER_VENDOR_ID, USB_VCI2_PRODUCT_ID), > + .driver_info = KVASER_HAS_TXRX_ERRORS }, > + > { } > }; > MODULE_DEVICE_TABLE(usb, kvaser_usb_table); > @@ -463,7 +636,18 @@ static int kvaser_usb_get_software_info(struct kvaser_usb *dev) > if (err) > return err; > > - dev->fw_version = le32_to_cpu(msg.u.softinfo.fw_version); > + switch (dev->family) { > + case KVASER_LEAF: > + dev->fw_version = le32_to_cpu(msg.u.leaf.softinfo.fw_version); > + break; > + case KVASER_USBCAN: > + dev->fw_version = le32_to_cpu(msg.u.usbcan.softinfo.fw_version); > + break; > + default: > + dev_err(dev->udev->dev.parent, > + "Invalid device family (%d)\n", dev->family); > + return -EINVAL; > + } > > return 0; > } > @@ -482,7 +666,7 @@ static int kvaser_usb_get_card_info(struct kvaser_usb *dev) > return err; > > dev->nchannels = msg.u.cardinfo.nchannels; > - if (dev->nchannels > MAX_NET_DEVICES) > + if (dev->nchannels > dev->max_channels) > return -EINVAL; IMHO, you can keep MAX_NET_DEVICES here. > > return 0; > @@ -496,8 +680,10 @@ static void kvaser_usb_tx_acknowledge(const struct kvaser_usb *dev, > struct kvaser_usb_net_priv *priv; > struct sk_buff *skb; > struct can_frame *cf; > - u8 channel = msg->u.tx_acknowledge.channel; > - u8 tid = msg->u.tx_acknowledge.tid; > + u8 channel, tid; > + > + channel = msg->u.tx_acknowledge_header.channel; > + tid = msg->u.tx_acknowledge_header.tid; > > if (channel >= dev->nchannels) { > dev_err(dev->udev->dev.parent, > @@ -615,37 +801,83 @@ static void kvaser_usb_unlink_tx_urbs(struct kvaser_usb_net_priv *priv) > priv->tx_contexts[i].echo_index = MAX_TX_URBS; > } > > -static void kvaser_usb_rx_error(const struct kvaser_usb *dev, > - const struct kvaser_msg *msg) > +static void kvaser_report_error_event(const struct kvaser_usb *dev, > + struct kvaser_error_summary *es); > + > +/* > + * Report error to userspace iff the controller's errors counter has > + * increased, or we're the only channel seeing the bus error state. > + * > + * As reported by USBCAN sheets, "the CAN controller has difficulties > + * to tell whether an error frame arrived on channel 1 or on channel 2." > + * Thus, error counters are compared with their earlier values to > + * determine which channel was responsible for the error event. > + */ > +static void usbcan_report_error_if_applicable(const struct kvaser_usb *dev, > + struct kvaser_error_summary *es) > { > - struct can_frame *cf; > - struct sk_buff *skb; > - struct net_device_stats *stats; > struct kvaser_usb_net_priv *priv; > - unsigned int new_state; > - u8 channel, status, txerr, rxerr, error_factor; > + int old_tx_err_count, old_rx_err_count, channel, report_error; > + > + channel = es->channel; > + if (channel >= dev->nchannels) { > + dev_err(dev->udev->dev.parent, > + "Invalid channel number (%d)\n", channel); > + return; > + } > + > + priv = dev->nets[channel]; > + old_tx_err_count = priv->bec.txerr; > + old_rx_err_count = priv->bec.rxerr; > + > + report_error = 0; > + if (es->txerr > old_tx_err_count) { > + es->usbcan.error_state |= USBCAN_ERROR_STATE_TX_ERROR; > + report_error = 1; > + } > + if (es->rxerr > old_rx_err_count) { > + es->usbcan.error_state |= USBCAN_ERROR_STATE_RX_ERROR; > + report_error = 1; > + } > + if ((es->status & M16C_STATE_BUS_ERROR) && > + !(es->usbcan.other_ch_status & M16C_STATE_BUS_ERROR)) { > + es->usbcan.error_state |= USBCAN_ERROR_STATE_BUSERROR; > + report_error = 1; > + } > + > + if (report_error) > + kvaser_report_error_event(dev, es); > +} > + > +/* > + * Extract error summary from a Leaf-based device error message > + */ > +static void leaf_extract_error_from_msg(const struct kvaser_usb *dev, > + const struct kvaser_msg *msg) > +{ > + struct kvaser_error_summary es = { 0, }; > > switch (msg->id) { > case CMD_CAN_ERROR_EVENT: > - channel = msg->u.error_event.channel; > - status = msg->u.error_event.status; > - txerr = msg->u.error_event.tx_errors_count; > - rxerr = msg->u.error_event.rx_errors_count; > - error_factor = msg->u.error_event.error_factor; > + es.channel = msg->u.leaf.error_event.channel; > + es.status = msg->u.leaf.error_event.status; > + es.txerr = msg->u.leaf.error_event.tx_errors_count; > + es.rxerr = msg->u.leaf.error_event.rx_errors_count; > + es.leaf.error_factor = msg->u.leaf.error_event.error_factor; > break; > - case CMD_LOG_MESSAGE: > - channel = msg->u.log_message.channel; > - status = msg->u.log_message.data[0]; > - txerr = msg->u.log_message.data[2]; > - rxerr = msg->u.log_message.data[3]; > - error_factor = msg->u.log_message.data[1]; > + case LEAF_CMD_LOG_MESSAGE: > + es.channel = msg->u.leaf.log_message.channel; > + es.status = msg->u.leaf.log_message.data[0]; > + es.txerr = msg->u.leaf.log_message.data[2]; > + es.rxerr = msg->u.leaf.log_message.data[3]; > + es.leaf.error_factor = msg->u.leaf.log_message.data[1]; > break; > case CMD_CHIP_STATE_EVENT: > - channel = msg->u.chip_state_event.channel; > - status = msg->u.chip_state_event.status; > - txerr = msg->u.chip_state_event.tx_errors_count; > - rxerr = msg->u.chip_state_event.rx_errors_count; > - error_factor = 0; > + es.channel = msg->u.leaf.chip_state_event.channel; > + es.status = msg->u.leaf.chip_state_event.status; > + es.txerr = msg->u.leaf.chip_state_event.tx_errors_count; > + es.rxerr = msg->u.leaf.chip_state_event.rx_errors_count; > + es.leaf.error_factor = 0; > break; > default: > dev_err(dev->udev->dev.parent, "Invalid msg id (%d)\n", > @@ -653,16 +885,92 @@ static void kvaser_usb_rx_error(const struct kvaser_usb *dev, > return; > } > > - if (channel >= dev->nchannels) { > + kvaser_report_error_event(dev, &es); > +} > + > +/* > + * Extract summary from a USBCANII-based device error message. > + */ > +static void usbcan_extract_error_from_msg(const struct kvaser_usb *dev, > + const struct kvaser_msg *msg) > +{ > + struct kvaser_error_summary es = { 0, }; > + > + switch (msg->id) { > + > + /* Sometimes errors are sent as unsolicited chip state events */ > + case CMD_CHIP_STATE_EVENT: > + es.channel = msg->u.usbcan.chip_state_event.channel; > + es.status = msg->u.usbcan.chip_state_event.status; > + es.txerr = msg->u.usbcan.chip_state_event.tx_errors_count; > + es.rxerr = msg->u.usbcan.chip_state_event.rx_errors_count; > + usbcan_report_error_if_applicable(dev, &es); > + break; > + > + case CMD_CAN_ERROR_EVENT: > + es.channel = 0; > + es.status = msg->u.usbcan.error_event.status_ch0; > + es.txerr = msg->u.usbcan.error_event.tx_errors_count_ch0; > + es.rxerr = msg->u.usbcan.error_event.rx_errors_count_ch0; > + es.usbcan.other_ch_status = > + msg->u.usbcan.error_event.status_ch1; > + usbcan_report_error_if_applicable(dev, &es); > + > + /* For error events, the USBCAN firmware does not support > + * more than 2 channels: ch0, and ch1. */ > + if (dev->nchannels > 1) { > + es.channel = 1; > + es.status = msg->u.usbcan.error_event.status_ch1; > + es.txerr = msg->u.usbcan.error_event.tx_errors_count_ch1; > + es.rxerr = msg->u.usbcan.error_event.rx_errors_count_ch1; > + es.usbcan.other_ch_status = > + msg->u.usbcan.error_event.status_ch0; > + usbcan_report_error_if_applicable(dev, &es); > + } > + break; > + > + default: > + dev_err(dev->udev->dev.parent, "Invalid msg id (%d)\n", > + msg->id); > + } > +} > + > +static void kvaser_usb_rx_error(const struct kvaser_usb *dev, > + const struct kvaser_msg *msg) > +{ > + switch (dev->family) { > + case KVASER_LEAF: > + leaf_extract_error_from_msg(dev, msg); > + break; > + case KVASER_USBCAN: > + usbcan_extract_error_from_msg(dev, msg); > + break; > + default: > dev_err(dev->udev->dev.parent, > - "Invalid channel number (%d)\n", channel); > + "Invalid device family (%d)\n", dev->family); > return; > } > +} > > - priv = dev->nets[channel]; > +static void kvaser_report_error_event(const struct kvaser_usb *dev, > + struct kvaser_error_summary *es) > +{ > + struct can_frame *cf; > + struct sk_buff *skb; > + struct net_device_stats *stats; > + struct kvaser_usb_net_priv *priv; > + unsigned int new_state; > + > + if (es->channel >= dev->nchannels) { > + dev_err(dev->udev->dev.parent, > + "Invalid channel number (%d)\n", es->channel); > + return; > + } > + > + priv = dev->nets[es->channel]; > stats = &priv->netdev->stats; > > - if (status & M16C_STATE_BUS_RESET) { > + if (es->status & M16C_STATE_BUS_RESET) { > kvaser_usb_unlink_tx_urbs(priv); > return; > } > @@ -675,9 +983,9 @@ static void kvaser_usb_rx_error(const struct kvaser_usb *dev, > > new_state = priv->can.state; > > - netdev_dbg(priv->netdev, "Error status: 0x%02x\n", status); > + netdev_dbg(priv->netdev, "Error status: 0x%02x\n", es->status); > > - if (status & M16C_STATE_BUS_OFF) { > + if (es->status & M16C_STATE_BUS_OFF) { > cf->can_id |= CAN_ERR_BUSOFF; > > priv->can.can_stats.bus_off++; > @@ -687,12 +995,12 @@ static void kvaser_usb_rx_error(const struct kvaser_usb *dev, > netif_carrier_off(priv->netdev); > > new_state = CAN_STATE_BUS_OFF; > - } else if (status & M16C_STATE_BUS_PASSIVE) { > + } else if (es->status & M16C_STATE_BUS_PASSIVE) { > if (priv->can.state != CAN_STATE_ERROR_PASSIVE) { > cf->can_id |= CAN_ERR_CRTL; > > - if (txerr || rxerr) > - cf->data[1] = (txerr > rxerr) > + if (es->txerr || es->rxerr) > + cf->data[1] = (es->txerr > es->rxerr) > ? CAN_ERR_CRTL_TX_PASSIVE > : CAN_ERR_CRTL_RX_PASSIVE; > else > @@ -703,13 +1011,11 @@ static void kvaser_usb_rx_error(const struct kvaser_usb *dev, > } > > new_state = CAN_STATE_ERROR_PASSIVE; > - } > - > - if (status == M16C_STATE_BUS_ERROR) { > + } else if (es->status & M16C_STATE_BUS_ERROR) { > if ((priv->can.state < CAN_STATE_ERROR_WARNING) && > - ((txerr >= 96) || (rxerr >= 96))) { > + ((es->txerr >= 96) || (es->rxerr >= 96))) { > cf->can_id |= CAN_ERR_CRTL; > - cf->data[1] = (txerr > rxerr) > + cf->data[1] = (es->txerr > es->rxerr) > ? CAN_ERR_CRTL_TX_WARNING > : CAN_ERR_CRTL_RX_WARNING; > > @@ -723,7 +1029,7 @@ static void kvaser_usb_rx_error(const struct kvaser_usb *dev, > } > } > > - if (!status) { > + if (!es->status) { > cf->can_id |= CAN_ERR_PROT; > cf->data[2] = CAN_ERR_PROT_ACTIVE; > > @@ -739,34 +1045,52 @@ static void kvaser_usb_rx_error(const struct kvaser_usb *dev, > priv->can.can_stats.restarts++; > } > > - if (error_factor) { > - priv->can.can_stats.bus_error++; > - stats->rx_errors++; > - > - cf->can_id |= CAN_ERR_BUSERROR | CAN_ERR_PROT; > - > - if (error_factor & M16C_EF_ACKE) > - cf->data[3] |= (CAN_ERR_PROT_LOC_ACK); > - if (error_factor & M16C_EF_CRCE) > - cf->data[3] |= (CAN_ERR_PROT_LOC_CRC_SEQ | > - CAN_ERR_PROT_LOC_CRC_DEL); > - if (error_factor & M16C_EF_FORME) > - cf->data[2] |= CAN_ERR_PROT_FORM; > - if (error_factor & M16C_EF_STFE) > - cf->data[2] |= CAN_ERR_PROT_STUFF; > - if (error_factor & M16C_EF_BITE0) > - cf->data[2] |= CAN_ERR_PROT_BIT0; > - if (error_factor & M16C_EF_BITE1) > - cf->data[2] |= CAN_ERR_PROT_BIT1; > - if (error_factor & M16C_EF_TRE) > - cf->data[2] |= CAN_ERR_PROT_TX; > + switch (dev->family) { > + case KVASER_LEAF: > + if (es->leaf.error_factor) { > + priv->can.can_stats.bus_error++; > + stats->rx_errors++; > + > + cf->can_id |= CAN_ERR_BUSERROR | CAN_ERR_PROT; > + > + if (es->leaf.error_factor & M16C_EF_ACKE) > + cf->data[3] |= (CAN_ERR_PROT_LOC_ACK); > + if (es->leaf.error_factor & M16C_EF_CRCE) > + cf->data[3] |= (CAN_ERR_PROT_LOC_CRC_SEQ | > + CAN_ERR_PROT_LOC_CRC_DEL); > + if (es->leaf.error_factor & M16C_EF_FORME) > + cf->data[2] |= CAN_ERR_PROT_FORM; > + if (es->leaf.error_factor & M16C_EF_STFE) > + cf->data[2] |= CAN_ERR_PROT_STUFF; > + if (es->leaf.error_factor & M16C_EF_BITE0) > + cf->data[2] |= CAN_ERR_PROT_BIT0; > + if (es->leaf.error_factor & M16C_EF_BITE1) > + cf->data[2] |= CAN_ERR_PROT_BIT1; > + if (es->leaf.error_factor & M16C_EF_TRE) > + cf->data[2] |= CAN_ERR_PROT_TX; > + } > + break; > + case KVASER_USBCAN: > + if (es->usbcan.error_state & USBCAN_ERROR_STATE_TX_ERROR) > + stats->tx_errors++; > + if (es->usbcan.error_state & USBCAN_ERROR_STATE_RX_ERROR) > + stats->rx_errors++; > + if (es->usbcan.error_state & USBCAN_ERROR_STATE_BUSERROR) { > + priv->can.can_stats.bus_error++; > + cf->can_id |= CAN_ERR_BUSERROR; > + } > + break; > + default: > + dev_err(dev->udev->dev.parent, > + "Invalid device family (%d)\n", dev->family); > + goto err; > } > > - cf->data[6] = txerr; > - cf->data[7] = rxerr; > + cf->data[6] = es->txerr; > + cf->data[7] = es->rxerr; > > - priv->bec.txerr = txerr; > - priv->bec.rxerr = rxerr; > + priv->bec.txerr = es->txerr; > + priv->bec.rxerr = es->rxerr; > > priv->can.state = new_state; > > @@ -774,6 +1098,11 @@ static void kvaser_usb_rx_error(const struct kvaser_usb *dev, > > stats->rx_packets++; > stats->rx_bytes += cf->can_dlc; > + > + return; > + > +err: > + dev_kfree_skb(skb); > } > > static void kvaser_usb_rx_can_err(const struct kvaser_usb_net_priv *priv, > @@ -783,16 +1112,16 @@ static void kvaser_usb_rx_can_err(const struct kvaser_usb_net_priv *priv, > struct sk_buff *skb; > struct net_device_stats *stats = &priv->netdev->stats; > > - if (msg->u.rx_can.flag & (MSG_FLAG_ERROR_FRAME | > + if (msg->u.rx_can_header.flag & (MSG_FLAG_ERROR_FRAME | > MSG_FLAG_NERR)) { > netdev_err(priv->netdev, "Unknow error (flags: 0x%02x)\n", > - msg->u.rx_can.flag); > + msg->u.rx_can_header.flag); > > stats->rx_errors++; > return; > } > > - if (msg->u.rx_can.flag & MSG_FLAG_OVERRUN) { > + if (msg->u.rx_can_header.flag & MSG_FLAG_OVERRUN) { > skb = alloc_can_err_skb(priv->netdev, &cf); > if (!skb) { > stats->rx_dropped++; > @@ -819,7 +1148,8 @@ static void kvaser_usb_rx_can_msg(const struct kvaser_usb *dev, > struct can_frame *cf; > struct sk_buff *skb; > struct net_device_stats *stats; > - u8 channel = msg->u.rx_can.channel; > + u8 channel = msg->u.rx_can_header.channel; > + const u8 *rx_msg; > > if (channel >= dev->nchannels) { > dev_err(dev->udev->dev.parent, > @@ -830,19 +1160,32 @@ static void kvaser_usb_rx_can_msg(const struct kvaser_usb *dev, > priv = dev->nets[channel]; > stats = &priv->netdev->stats; > > - if ((msg->u.rx_can.flag & MSG_FLAG_ERROR_FRAME) && > - (msg->id == CMD_LOG_MESSAGE)) { > + if ((msg->u.rx_can_header.flag & MSG_FLAG_ERROR_FRAME) && > + (dev->family == KVASER_LEAF && msg->id == LEAF_CMD_LOG_MESSAGE)) { > kvaser_usb_rx_error(dev, msg); > return; > - } else if (msg->u.rx_can.flag & (MSG_FLAG_ERROR_FRAME | > - MSG_FLAG_NERR | > - MSG_FLAG_OVERRUN)) { > + } else if (msg->u.rx_can_header.flag & (MSG_FLAG_ERROR_FRAME | > + MSG_FLAG_NERR | > + MSG_FLAG_OVERRUN)) { > kvaser_usb_rx_can_err(priv, msg); > return; > - } else if (msg->u.rx_can.flag & ~MSG_FLAG_REMOTE_FRAME) { > + } else if (msg->u.rx_can_header.flag & ~MSG_FLAG_REMOTE_FRAME) { > netdev_warn(priv->netdev, > "Unhandled frame (flags: 0x%02x)", > - msg->u.rx_can.flag); > + msg->u.rx_can_header.flag); > + return; > + } > + > + switch (dev->family) { > + case KVASER_LEAF: > + rx_msg = msg->u.leaf.rx_can.msg; > + break; > + case KVASER_USBCAN: > + rx_msg = msg->u.usbcan.rx_can.msg; > + break; > + default: > + dev_err(dev->udev->dev.parent, > + "Invalid device family (%d)\n", dev->family); > return; > } > > @@ -852,38 +1195,37 @@ static void kvaser_usb_rx_can_msg(const struct kvaser_usb *dev, > return; > } > > - if (msg->id == CMD_LOG_MESSAGE) { > - cf->can_id = le32_to_cpu(msg->u.log_message.id); > + if (dev->family == KVASER_LEAF && msg->id == LEAF_CMD_LOG_MESSAGE) { > + cf->can_id = le32_to_cpu(msg->u.leaf.log_message.id); > if (cf->can_id & KVASER_EXTENDED_FRAME) > cf->can_id &= CAN_EFF_MASK | CAN_EFF_FLAG; > else > cf->can_id &= CAN_SFF_MASK; > > - cf->can_dlc = get_can_dlc(msg->u.log_message.dlc); > + cf->can_dlc = get_can_dlc(msg->u.leaf.log_message.dlc); > > - if (msg->u.log_message.flags & MSG_FLAG_REMOTE_FRAME) > + if (msg->u.leaf.log_message.flags & MSG_FLAG_REMOTE_FRAME) > cf->can_id |= CAN_RTR_FLAG; > else > - memcpy(cf->data, &msg->u.log_message.data, > + memcpy(cf->data, &msg->u.leaf.log_message.data, > cf->can_dlc); > } else { > - cf->can_id = ((msg->u.rx_can.msg[0] & 0x1f) << 6) | > - (msg->u.rx_can.msg[1] & 0x3f); > + cf->can_id = ((rx_msg[0] & 0x1f) << 6) | (rx_msg[1] & 0x3f); > > if (msg->id == CMD_RX_EXT_MESSAGE) { > cf->can_id <<= 18; > - cf->can_id |= ((msg->u.rx_can.msg[2] & 0x0f) << 14) | > - ((msg->u.rx_can.msg[3] & 0xff) << 6) | > - (msg->u.rx_can.msg[4] & 0x3f); > + cf->can_id |= ((rx_msg[2] & 0x0f) << 14) | > + ((rx_msg[3] & 0xff) << 6) | > + (rx_msg[4] & 0x3f); > cf->can_id |= CAN_EFF_FLAG; > } > > - cf->can_dlc = get_can_dlc(msg->u.rx_can.msg[5]); > + cf->can_dlc = get_can_dlc(rx_msg[5]); > > - if (msg->u.rx_can.flag & MSG_FLAG_REMOTE_FRAME) > + if (msg->u.rx_can_header.flag & MSG_FLAG_REMOTE_FRAME) > cf->can_id |= CAN_RTR_FLAG; > else > - memcpy(cf->data, &msg->u.rx_can.msg[6], > + memcpy(cf->data, &rx_msg[6], > cf->can_dlc); > } > > @@ -947,7 +1289,12 @@ static void kvaser_usb_handle_message(const struct kvaser_usb *dev, > > case CMD_RX_STD_MESSAGE: > case CMD_RX_EXT_MESSAGE: > - case CMD_LOG_MESSAGE: > + kvaser_usb_rx_can_msg(dev, msg); > + break; > + > + case LEAF_CMD_LOG_MESSAGE: > + if (dev->family != KVASER_LEAF) > + goto warn; > kvaser_usb_rx_can_msg(dev, msg); > break; > > @@ -960,8 +1307,14 @@ static void kvaser_usb_handle_message(const struct kvaser_usb *dev, > kvaser_usb_tx_acknowledge(dev, msg); > break; > > + /* Ignored messages */ > + case USBCAN_CMD_CLOCK_OVERFLOW_EVENT: > + if (dev->family != KVASER_USBCAN) > + goto warn; > + break; > + > default: > - dev_warn(dev->udev->dev.parent, > +warn: dev_warn(dev->udev->dev.parent, > "Unhandled message (%d)\n", msg->id); > break; > } > @@ -1181,7 +1534,7 @@ static void kvaser_usb_unlink_all_urbs(struct kvaser_usb *dev) > dev->rxbuf[i], > dev->rxbuf_dma[i]); > > - for (i = 0; i < MAX_NET_DEVICES; i++) { > + for (i = 0; i < dev->max_channels; i++) { here too... or replace it by nchannels. > struct kvaser_usb_net_priv *priv = dev->nets[i]; > > if (priv) > @@ -1286,6 +1639,7 @@ static netdev_tx_t kvaser_usb_start_xmit(struct sk_buff *skb, > struct kvaser_msg *msg; > int i, err; > int ret = NETDEV_TX_OK; > + uint8_t *msg_tx_can_flags; > bool kfree_skb_on_error = true; > > if (can_dropped_invalid_skb(netdev, skb)) > @@ -1306,9 +1660,23 @@ static netdev_tx_t kvaser_usb_start_xmit(struct sk_buff *skb, > > msg = buf; > msg->len = MSG_HEADER_LEN + sizeof(struct kvaser_msg_tx_can); > - msg->u.tx_can.flags = 0; > msg->u.tx_can.channel = priv->channel; > > + switch (dev->family) { > + case KVASER_LEAF: > + msg_tx_can_flags = &msg->u.tx_can.leaf.flags; > + break; > + case KVASER_USBCAN: > + msg_tx_can_flags = &msg->u.tx_can.usbcan.flags; > + break; > + default: > + dev_err(dev->udev->dev.parent, > + "Invalid device family (%d)\n", dev->family); > + goto releasebuf; > + } > + > + *msg_tx_can_flags = 0; > + > if (cf->can_id & CAN_EFF_FLAG) { > msg->id = CMD_TX_EXT_MESSAGE; > msg->u.tx_can.msg[0] = (cf->can_id >> 24) & 0x1f; > @@ -1326,7 +1694,7 @@ static netdev_tx_t kvaser_usb_start_xmit(struct sk_buff *skb, > memcpy(&msg->u.tx_can.msg[6], cf->data, cf->can_dlc); > > if (cf->can_id & CAN_RTR_FLAG) > - msg->u.tx_can.flags |= MSG_FLAG_REMOTE_FRAME; > + *msg_tx_can_flags |= MSG_FLAG_REMOTE_FRAME; > > for (i = 0; i < ARRAY_SIZE(priv->tx_contexts); i++) { > if (priv->tx_contexts[i].echo_index == MAX_TX_URBS) { > @@ -1596,6 +1964,18 @@ static int kvaser_usb_probe(struct usb_interface *intf, > if (!dev) > return -ENOMEM; > > + if (LEAF_PRODUCT_ID(id->idProduct)) { > + dev->family = KVASER_LEAF; > + dev->max_channels = LEAF_MAX_NET_DEVICES; > + } else if (USBCAN_PRODUCT_ID(id->idProduct)) { > + dev->family = KVASER_USBCAN; > + dev->max_channels = USBCAN_MAX_NET_DEVICES; > + } else { > + dev_err(&intf->dev, "Product ID (%d) does not belong to any " > + "known Kvaser USB family", id->idProduct); > + return -ENODEV; > + } Is it really required to keep max_channels in the kvaser_usb structure? If I looked correctly, you use this variable as a replacement for MAX_NET_DEVICES in the code and MAX_NET_DEVICES is only used in probe and disconnect functions. I think it can even be replaced by nchannels in the disconnect path. So I also think that it don't need to be in the kvaser_usb structure. > + > err = kvaser_usb_get_endpoints(intf, &dev->bulk_in, &dev->bulk_out); > if (err) { > dev_err(&intf->dev, "Cannot get usb endpoint(s)"); > @@ -1608,7 +1988,7 @@ static int kvaser_usb_probe(struct usb_interface *intf, > > usb_set_intfdata(intf, dev); > > - for (i = 0; i < MAX_NET_DEVICES; i++) > + for (i = 0; i < dev->max_channels; i++) > kvaser_usb_send_simple_msg(dev, CMD_RESET_CHIP, i); Someone reported me that recent leaf firmwares go in trouble when you send a command for a channel that does not exist. Instead of max_channels, you can use nchannels here and move the reset command in the kvaser_usb_init_one() function. I've a patch for this but It is not tested yet. I'll send it next week-end after I did some tests. > > err = kvaser_usb_get_software_info(dev); Thank you, -- Olivier -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/