Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id ; Sun, 5 Jan 2003 11:46:08 -0500 Received: (majordomo@vger.kernel.org) by vger.kernel.org id ; Sun, 5 Jan 2003 11:46:08 -0500 Received: from ulima.unil.ch ([130.223.144.143]:14521 "EHLO ulima.unil.ch") by vger.kernel.org with ESMTP id ; Sun, 5 Jan 2003 11:46:06 -0500 Date: Sun, 5 Jan 2003 17:54:41 +0100 From: Gregoire Favre To: linux-kernel@vger.kernel.org Subject: 2.5.54 problem with IDE ICH4 and aic7xxx Message-ID: <20030105165441.GA8215@ulima.unil.ch> Mime-Version: 1.0 Content-Type: text/plain; charset=iso-8859-1 Content-Disposition: inline Content-Transfer-Encoding: 8bit User-Agent: Mutt/1.4i Sender: linux-kernel-owner@vger.kernel.org X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 4992 Lines: 110 Hello, I have put whole dmesg, .config, lspci, ver_linux, /proc/interrupts, /proc/ide/piix, /proc/partitions, /proc/scsi/aic7xxx/0, /proc/scsi/aic7xxx/1, /proc/scsi/scsi under http://ulima.unil.ch/greg/linux/2.5.54/ One could also find patch-2.5.45-mouse that I used such that my mouse work (wireless one, reverse patch), and other patch I have applied are the ones from linux-dvb : cvs -d :pserver:anonymous@linuxtv.org:/cvs/linuxtv co dvb-kernel But I get the same result without those patches ;-) I got an MSI Max2-BLR which has an onboard IDE Raid that isn't acticated in the BIOS (if I turn it on, it doesn't change anything at all... Under 2.4.20 it boots perfectly... What I found really strange is the time my IDE take to boot. More than five minutes for thoses lines : Linux video capture interface: v1.00 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH4: IDE controller at PCI slot 00:1f.1 ICH4: chipset revision 1 ICH4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio hda: IC35L120AVVA07-0, ATA DISK drive hda: bad special flag: 0x03 hda: tagged command queueing enabled, command queue depth 8 ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: SONY DVD RW DRU-500A, ATAPI CD/DVD-ROM drive hdd: IOMEGA ZIP 250 ATAPI, ATAPI FLOPPY drive ide1 at 0x170-0x177,0x376 on irq 15 hda: host protected area => 1 hda: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=239340/16/63, UDMA(100) /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 > hdc: ATAPI 16X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 ide-floppy driver 0.99.newide hdd: 244766kB, 489532 blocks, 512 sector size hdd: 244736kB, 239/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm hdd: The disk reports a capacity of 250640384 bytes, but the drive only handles 250 609664 hdd: The disk reports a capacity of 250640384 bytes, but the drive only handles 250 609664 /dev/ide/host0/bus1/target1/lun0: unknown partition table /dev/ide/host0/bus1/target1/lun0: unknown partition table Which is imediatly followed by: aic7xxx: PCI Device 3:3:0 failed memory mapped test. Using PIO. scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.25 aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs (scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 15, 16bit) (scsi1:A:1:0): refuses WIDE negotiation. Using 8bit transfers (scsi0:A:15): 160.000MB/s transfers (80.000MHz DT, offset 63, 16bit) Vendor: IBM Model: DDRS-39130D Rev: DC1B Type: Direct-Access ANSI SCSI revision: 02 scsi0:A:0:0: Tagged Queuing enabled. Depth 253 Vendor: SEAGATE Model: ST336706LW Rev: 0108 Type: Direct-Access ANSI SCSI revision: 03 scsi0:A:15:0: Tagged Queuing enabled. Depth 253 scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.25 aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs (scsi1:A:1): 10.000MB/s transfers (10.000MHz, offset 15) (scsi1:A:2): 10.000MB/s transfers (10.000MHz, offset 8) (scsi1:A:3): 10.000MB/s transfers (10.000MHz, offset 8) Vendor: TOSHIBA Model: DVD-ROM SD-M1201 Rev: 1R04 Type: CD-ROM ANSI SCSI revision: 02 Vendor: PLEXTOR Model: CD-R PX-R820T Rev: 1.08 Type: CD-ROM ANSI SCSI revision: 02 Vendor: PLEXTOR Model: CD-R PX-R820T Rev: 1.08 Type: CD-ROM ANSI SCSI revision: 02 SCSI device sda: drive cache: write through SCSI device sda: 17850000 512-byte hdwr sectors (9139 MB) /dev/scsi/host0/bus0/target0/lun0: p1 p2 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 SCSI device sdb: drive cache: write back SCSI device sdb: 71687370 512-byte hdwr sectors (36704 MB) /dev/scsi/host0/bus0/target15/lun0: p1 p2 Attached scsi disk sdb at scsi0, channel 0, id 15, lun 0 sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray Attached scsi CD-ROM sr0 at scsi1, channel 0, id 1, lun 0 sr1: scsi3-mmc drive: 20x/20x writer cd/rw xa/form2 cdda tray Attached scsi CD-ROM sr1 at scsi1, channel 0, id 2, lun 0 sr2: scsi3-mmc drive: 20x/20x writer cd/rw xa/form2 cdda tray Attached scsi CD-ROM sr2 at scsi1, channel 0, id 3, lun 0 device class 'input': registering Should I do something different? Thank you very much and have a great day ;-) Gr?goire ________________________________________________________________ http://ulima.unil.ch/greg ICQ:16624071 mailto:greg@ulima.unil.ch - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/