Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1754866AbbBJWQB (ORCPT ); Tue, 10 Feb 2015 17:16:01 -0500 Received: from mail-gw1-out.broadcom.com ([216.31.210.62]:37763 "EHLO mail-gw1-out.broadcom.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1754740AbbBJWPD (ORCPT ); Tue, 10 Feb 2015 17:15:03 -0500 X-IronPort-AV: E=Sophos;i="5.09,553,1418112000"; d="scan'208";a="56980527" From: Ray Jui To: Linus Walleij , Alexandre Courbot , Rob Herring , Pawel Moll , Mark Rutland , Ian Campbell , Kumar Gala , "Grant Likely" , Christian Daudt , Matt Porter , Florian Fainelli , Russell King , Joe Perches , "Arnd Bergmann" CC: Scott Branden , Dmitry Torokhov , Anatol Pomazau , , , , , , "Ray Jui" Subject: [PATCH v9 2/4] pinctrl: cygnus: add gpio/pinconf driver Date: Tue, 10 Feb 2015 14:16:22 -0800 Message-ID: <1423606584-21795-3-git-send-email-rjui@broadcom.com> X-Mailer: git-send-email 1.7.9.5 In-Reply-To: <1423606584-21795-1-git-send-email-rjui@broadcom.com> References: <1423606584-21795-1-git-send-email-rjui@broadcom.com> MIME-Version: 1.0 Content-Type: text/plain Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 27416 Lines: 983 This adds the initial support of the Broadcom Cygnus GPIO/PINCONF driver that supports all 3 GPIO controllers on Cygnus including the ASIU GPIO controller, the chipCommonG GPIO controller, and the always-on GPIO controller. Basic PINCONF configurations such as bias pull up/down, and drive strength are also supported in this driver. Pins from the ASIU GPIO controller can be individually muxed to GPIO function, through interaction with the Cygnus IOMUX controller Signed-off-by: Ray Jui Reviewed-by: Scott Branden --- drivers/pinctrl/bcm/Kconfig | 22 + drivers/pinctrl/bcm/Makefile | 1 + drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c | 908 +++++++++++++++++++++++++++++ 3 files changed, 931 insertions(+) create mode 100644 drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c diff --git a/drivers/pinctrl/bcm/Kconfig b/drivers/pinctrl/bcm/Kconfig index eb13201..cd11d4d 100644 --- a/drivers/pinctrl/bcm/Kconfig +++ b/drivers/pinctrl/bcm/Kconfig @@ -20,6 +20,28 @@ config PINCTRL_BCM2835 select PINMUX select PINCONF +config PINCTRL_CYGNUS_GPIO + bool "Broadcom Cygnus GPIO (with PINCONF) driver" + depends on OF_GPIO && ARCH_BCM_CYGNUS + select GPIOLIB_IRQCHIP + select PINCONF + select GENERIC_PINCONF + default ARCH_BCM_CYGNUS + help + Say yes here to enable the Broadcom Cygnus GPIO driver. + + The Broadcom Cygnus SoC has 3 GPIO controllers including the ASIU + GPIO controller (ASIU), the chipCommonG GPIO controller (CCM), and + the always-ON GPIO controller (CRMU/AON). All 3 GPIO controllers are + supported by this driver. + + All 3 Cygnus GPIO controllers support basic PINCONF functions such + as bias pull up, pull down, and drive strength configurations, when + these pins are muxed to GPIO. + + Pins from the ASIU GPIO can be individually muxed to GPIO function, + through interaction with the Cygnus IOMUX controller. + config PINCTRL_CYGNUS_MUX bool "Broadcom Cygnus IOMUX driver" depends on (ARCH_BCM_CYGNUS || COMPILE_TEST) diff --git a/drivers/pinctrl/bcm/Makefile b/drivers/pinctrl/bcm/Makefile index bb6beb6..2b2f70e 100644 --- a/drivers/pinctrl/bcm/Makefile +++ b/drivers/pinctrl/bcm/Makefile @@ -2,4 +2,5 @@ obj-$(CONFIG_PINCTRL_BCM281XX) += pinctrl-bcm281xx.o obj-$(CONFIG_PINCTRL_BCM2835) += pinctrl-bcm2835.o +obj-$(CONFIG_PINCTRL_CYGNUS_GPIO) += pinctrl-cygnus-gpio.o obj-$(CONFIG_PINCTRL_CYGNUS_MUX) += pinctrl-cygnus-mux.o diff --git a/drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c b/drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c new file mode 100644 index 0000000..f2e5aec --- /dev/null +++ b/drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c @@ -0,0 +1,908 @@ +/* + * Copyright (C) 2014-2015 Broadcom Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation version 2. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * This file contains the Broadcom Cygnus GPIO driver that supports 3 + * GPIO controllers on Cygnus including the ASIU GPIO controller, the + * chipCommonG GPIO controller, and the always-on GPIO controller. Basic + * PINCONF such as bias pull up/down, and drive strength are also supported + * in this driver. + * + * Pins from the ASIU GPIO can be individually muxed to GPIO function, + * through the interaction with the Cygnus IOMUX controller + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "../pinctrl-utils.h" + +#define CYGNUS_GPIO_DATA_IN_OFFSET 0x00 +#define CYGNUS_GPIO_DATA_OUT_OFFSET 0x04 +#define CYGNUS_GPIO_OUT_EN_OFFSET 0x08 +#define CYGNUS_GPIO_IN_TYPE_OFFSET 0x0c +#define CYGNUS_GPIO_INT_DE_OFFSET 0x10 +#define CYGNUS_GPIO_INT_EDGE_OFFSET 0x14 +#define CYGNUS_GPIO_INT_MSK_OFFSET 0x18 +#define CYGNUS_GPIO_INT_STAT_OFFSET 0x1c +#define CYGNUS_GPIO_INT_MSTAT_OFFSET 0x20 +#define CYGNUS_GPIO_INT_CLR_OFFSET 0x24 +#define CYGNUS_GPIO_PAD_RES_OFFSET 0x34 +#define CYGNUS_GPIO_RES_EN_OFFSET 0x38 + +/* drive strength control for ASIU GPIO */ +#define CYGNUS_GPIO_ASIU_DRV0_CTRL_OFFSET 0x58 + +/* drive strength control for CCM/CRMU (AON) GPIO */ +#define CYGNUS_GPIO_DRV0_CTRL_OFFSET 0x00 + +#define GPIO_BANK_SIZE 0x200 +#define NGPIOS_PER_BANK 32 +#define GPIO_BANK(pin) ((pin) / NGPIOS_PER_BANK) + +#define CYGNUS_GPIO_REG(pin, reg) (GPIO_BANK(pin) * GPIO_BANK_SIZE + (reg)) +#define CYGNUS_GPIO_SHIFT(pin) ((pin) % NGPIOS_PER_BANK) + +#define GPIO_DRV_STRENGTH_BIT_SHIFT 20 +#define GPIO_DRV_STRENGTH_BITS 3 +#define GPIO_DRV_STRENGTH_BIT_MASK ((1 << GPIO_DRV_STRENGTH_BITS) - 1) + +/* + * Cygnus GPIO core + * + * @dev: pointer to device + * @base: I/O register base for Cygnus GPIO controller + * @io_ctrl: I/O register base for certain type of Cygnus GPIO controller that + * has the PINCONF support implemented outside of the GPIO block + * @lock: lock to protect access to I/O registers + * @gc: GPIO chip + * @num_banks: number of GPIO banks, each bank supports up to 32 GPIOs + * @pinmux_is_supported: flag to indicate this GPIO controller contains pins + * that can be individually muxed to GPIO + * @pctl: pointer to pinctrl_dev + * @pctldesc: pinctrl descriptor + */ +struct cygnus_gpio { + struct device *dev; + + void __iomem *base; + void __iomem *io_ctrl; + + spinlock_t lock; + + struct gpio_chip gc; + unsigned num_banks; + + bool pinmux_is_supported; + + struct pinctrl_dev *pctl; + struct pinctrl_desc pctldesc; +}; + +static struct cygnus_gpio *to_cygnus_gpio(struct gpio_chip *gc) +{ + return container_of(gc, struct cygnus_gpio, gc); +} + +/* + * Mapping from PINCONF pins to GPIO pins is 1-to-1 + */ +static unsigned cygnus_pin_to_gpio(unsigned pin) +{ + return pin; +} + +static u32 cygnus_readl(struct cygnus_gpio *chip, unsigned int offset) +{ + return readl(chip->base + offset); +} + +static void cygnus_writel(struct cygnus_gpio *chip, unsigned int offset, + u32 val) +{ + writel(val, chip->base + offset); +} + +/** + * cygnus_set_bit - set or clear one bit (corresponding to the GPIO pin) in a + * Cygnus GPIO register + * + * @cygnus_gpio: Cygnus GPIO device + * @reg: register offset + * @gpio: GPIO pin + * @set: set or clear. 1 - set; 0 -clear + */ +static void cygnus_set_bit(struct cygnus_gpio *chip, unsigned int reg, + unsigned gpio, int set) +{ + unsigned int offset = CYGNUS_GPIO_REG(gpio, reg); + unsigned int shift = CYGNUS_GPIO_SHIFT(gpio); + u32 val; + + val = cygnus_readl(chip, offset); + if (set) + val |= BIT(shift); + else + val &= ~BIT(shift); + cygnus_writel(chip, offset, val); +} + +static int cygnus_get_bit(struct cygnus_gpio *chip, unsigned int reg, + unsigned gpio) +{ + unsigned int offset = CYGNUS_GPIO_REG(gpio, reg); + unsigned int shift = CYGNUS_GPIO_SHIFT(gpio); + u32 val; + + val = cygnus_readl(chip, offset) & BIT(shift); + if (val) + return 1; + else + return 0; +} + +static void cygnus_gpio_irq_handler(unsigned int irq, struct irq_desc *desc) +{ + struct gpio_chip *gc = irq_desc_get_handler_data(desc); + struct cygnus_gpio *chip = to_cygnus_gpio(gc); + struct irq_chip *irq_chip = irq_desc_get_chip(desc); + int i, bit; + + chained_irq_enter(irq_chip, desc); + + /* go through the entire GPIO banks and handle all interrupts */ + for (i = 0; i < chip->num_banks; i++) { + unsigned long val = cygnus_readl(chip, + (i * GPIO_BANK_SIZE) + + CYGNUS_GPIO_INT_MSTAT_OFFSET); + + for_each_set_bit(bit, &val, NGPIOS_PER_BANK) { + unsigned pin = NGPIOS_PER_BANK * i + bit; + int child_irq = irq_find_mapping(gc->irqdomain, pin); + + /* + * Clear the interrupt before invoking the + * handler, so we do not leave any window + */ + cygnus_writel(chip, (i * GPIO_BANK_SIZE) + + CYGNUS_GPIO_INT_CLR_OFFSET, BIT(bit)); + + generic_handle_irq(child_irq); + } + } + + chained_irq_exit(irq_chip, desc); +} + + +static void cygnus_gpio_irq_ack(struct irq_data *d) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct cygnus_gpio *chip = to_cygnus_gpio(gc); + unsigned gpio = d->hwirq; + unsigned int offset = CYGNUS_GPIO_REG(gpio, + CYGNUS_GPIO_INT_CLR_OFFSET); + unsigned int shift = CYGNUS_GPIO_SHIFT(gpio); + u32 val = BIT(shift); + + cygnus_writel(chip, offset, val); +} + +/** + * cygnus_gpio_irq_set_mask - mask/unmask a GPIO interrupt + * + * @d: IRQ chip data + * @mask: mask/unmask GPIO interrupt. 0 - mask (disable); 1 - unmask (enable) + */ +static void cygnus_gpio_irq_set_mask(struct irq_data *d, int mask) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct cygnus_gpio *chip = to_cygnus_gpio(gc); + unsigned gpio = d->hwirq; + + cygnus_set_bit(chip, CYGNUS_GPIO_INT_MSK_OFFSET, gpio, mask); +} + +static void cygnus_gpio_irq_mask(struct irq_data *d) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct cygnus_gpio *chip = to_cygnus_gpio(gc); + unsigned long flags; + + spin_lock_irqsave(&chip->lock, flags); + cygnus_gpio_irq_set_mask(d, 0); + spin_unlock_irqrestore(&chip->lock, flags); +} + +static void cygnus_gpio_irq_unmask(struct irq_data *d) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct cygnus_gpio *chip = to_cygnus_gpio(gc); + unsigned long flags; + + spin_lock_irqsave(&chip->lock, flags); + cygnus_gpio_irq_set_mask(d, 1); + spin_unlock_irqrestore(&chip->lock, flags); +} + +static int cygnus_gpio_irq_set_type(struct irq_data *d, unsigned int type) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct cygnus_gpio *chip = to_cygnus_gpio(gc); + unsigned gpio = d->hwirq; + int int_type = 0, dual_edge = 0, edge_lvl = 0; + unsigned long flags; + + switch (type & IRQ_TYPE_SENSE_MASK) { + case IRQ_TYPE_EDGE_RISING: + edge_lvl = 1; + break; + + case IRQ_TYPE_EDGE_FALLING: + break; + + case IRQ_TYPE_EDGE_BOTH: + dual_edge = 1; + break; + + case IRQ_TYPE_LEVEL_HIGH: + int_type = 1; + edge_lvl = 1; + break; + + case IRQ_TYPE_LEVEL_LOW: + int_type = 1; + break; + + default: + dev_err(chip->dev, "invalid GPIO IRQ type 0x%x\n", + type); + return -EINVAL; + } + + spin_lock_irqsave(&chip->lock, flags); + cygnus_set_bit(chip, CYGNUS_GPIO_IN_TYPE_OFFSET, gpio, int_type); + cygnus_set_bit(chip, CYGNUS_GPIO_INT_DE_OFFSET, gpio, dual_edge); + cygnus_set_bit(chip, CYGNUS_GPIO_INT_EDGE_OFFSET, gpio, + edge_lvl); + spin_unlock_irqrestore(&chip->lock, flags); + + dev_dbg(chip->dev, + "gpio:%u set int_type:%d dual_edge:%d edge_lvl:%d\n", + gpio, int_type, dual_edge, edge_lvl); + + return 0; +} + +static struct irq_chip cygnus_gpio_irq_chip = { + .name = "bcm-cygnus-gpio", + .irq_ack = cygnus_gpio_irq_ack, + .irq_mask = cygnus_gpio_irq_mask, + .irq_unmask = cygnus_gpio_irq_unmask, + .irq_set_type = cygnus_gpio_irq_set_type, +}; + +/* + * Request the Cygnus IOMUX pinmux controller to mux individual pins to GPIO + */ +static int cygnus_gpio_request(struct gpio_chip *gc, unsigned offset) +{ + struct cygnus_gpio *chip = to_cygnus_gpio(gc); + unsigned gpio = gc->base + offset; + + /* not all Cygnus GPIO pins can be muxed individually */ + if (!chip->pinmux_is_supported) + return 0; + + return pinctrl_request_gpio(gpio); +} + +static void cygnus_gpio_free(struct gpio_chip *gc, unsigned offset) +{ + struct cygnus_gpio *chip = to_cygnus_gpio(gc); + unsigned gpio = gc->base + offset; + + if (!chip->pinmux_is_supported) + return; + + pinctrl_free_gpio(gpio); +} + +static int cygnus_gpio_direction_input(struct gpio_chip *gc, unsigned gpio) +{ + struct cygnus_gpio *chip = to_cygnus_gpio(gc); + unsigned long flags; + + spin_lock_irqsave(&chip->lock, flags); + cygnus_set_bit(chip, CYGNUS_GPIO_OUT_EN_OFFSET, gpio, 0); + spin_unlock_irqrestore(&chip->lock, flags); + + dev_dbg(chip->dev, "gpio:%u set input\n", gpio); + + return 0; +} + +static int cygnus_gpio_direction_output(struct gpio_chip *gc, unsigned gpio, + int value) +{ + struct cygnus_gpio *chip = to_cygnus_gpio(gc); + unsigned long flags; + + spin_lock_irqsave(&chip->lock, flags); + cygnus_set_bit(chip, CYGNUS_GPIO_OUT_EN_OFFSET, gpio, 1); + cygnus_set_bit(chip, CYGNUS_GPIO_DATA_OUT_OFFSET, gpio, value); + spin_unlock_irqrestore(&chip->lock, flags); + + dev_dbg(chip->dev, "gpio:%u set output, value:%d\n", gpio, value); + + return 0; +} + +static void cygnus_gpio_set(struct gpio_chip *gc, unsigned gpio, int value) +{ + struct cygnus_gpio *chip = to_cygnus_gpio(gc); + unsigned long flags; + + spin_lock_irqsave(&chip->lock, flags); + cygnus_set_bit(chip, CYGNUS_GPIO_DATA_OUT_OFFSET, gpio, value); + spin_unlock_irqrestore(&chip->lock, flags); + + dev_dbg(chip->dev, "gpio:%u set, value:%d\n", gpio, value); +} + +static int cygnus_gpio_get(struct gpio_chip *gc, unsigned gpio) +{ + struct cygnus_gpio *chip = to_cygnus_gpio(gc); + unsigned int offset = CYGNUS_GPIO_REG(gpio, + CYGNUS_GPIO_DATA_IN_OFFSET); + unsigned int shift = CYGNUS_GPIO_SHIFT(gpio); + + return !!(cygnus_readl(chip, offset) & BIT(shift)); +} + +static int cygnus_get_groups_count(struct pinctrl_dev *pctldev) +{ + return 1; +} + +/* + * Only one group: "gpio_grp", since this local pinctrl device only performs + * GPIO specific PINCONF configurations + */ +static const char *cygnus_get_group_name(struct pinctrl_dev *pctldev, + unsigned selector) +{ + return "gpio_grp"; +} + +static const struct pinctrl_ops cygnus_pctrl_ops = { + .get_groups_count = cygnus_get_groups_count, + .get_group_name = cygnus_get_group_name, + .dt_node_to_map = pinconf_generic_dt_node_to_map_pin, + .dt_free_map = pinctrl_utils_dt_free_map, +}; + +static int cygnus_gpio_set_pull(struct cygnus_gpio *chip, unsigned gpio, + int disable, int pull_up) +{ + unsigned long flags; + + spin_lock_irqsave(&chip->lock, flags); + + if (disable) { + cygnus_set_bit(chip, CYGNUS_GPIO_RES_EN_OFFSET, gpio, 0); + } else { + cygnus_set_bit(chip, CYGNUS_GPIO_PAD_RES_OFFSET, gpio, + pull_up); + cygnus_set_bit(chip, CYGNUS_GPIO_RES_EN_OFFSET, gpio, 1); + } + + spin_unlock_irqrestore(&chip->lock, flags); + + dev_dbg(chip->dev, "gpio:%u set pullup:%d\n", gpio, pull_up); + + return 0; +} + +static void cygnus_gpio_get_pull(struct cygnus_gpio *chip, unsigned gpio, + int *disable, int *pull_up) +{ + unsigned long flags; + + spin_lock_irqsave(&chip->lock, flags); + *disable = !cygnus_get_bit(chip, CYGNUS_GPIO_RES_EN_OFFSET, gpio); + *pull_up = cygnus_get_bit(chip, CYGNUS_GPIO_PAD_RES_OFFSET, gpio); + spin_unlock_irqrestore(&chip->lock, flags); +} + +static int cygnus_gpio_set_strength(struct cygnus_gpio *chip, unsigned gpio, + unsigned strength) +{ + void __iomem *base; + unsigned int i, offset, shift; + u32 val; + unsigned long flags; + + /* make sure drive strength is supported */ + if (strength < 2 || strength > 16 || (strength % 2)) + return -ENOTSUPP; + + if (chip->io_ctrl) { + base = chip->io_ctrl; + offset = CYGNUS_GPIO_DRV0_CTRL_OFFSET; + } else { + base = chip->base; + offset = CYGNUS_GPIO_REG(gpio, + CYGNUS_GPIO_ASIU_DRV0_CTRL_OFFSET); + } + + shift = CYGNUS_GPIO_SHIFT(gpio); + + dev_dbg(chip->dev, "gpio:%u set drive strength:%d mA\n", gpio, + strength); + + spin_lock_irqsave(&chip->lock, flags); + strength = (strength / 2) - 1; + for (i = 0; i < GPIO_DRV_STRENGTH_BITS; i++) { + val = readl(base + offset); + val &= ~BIT(shift); + val |= ((strength >> i) & 0x1) << shift; + writel(val, base + offset); + offset += 4; + } + spin_unlock_irqrestore(&chip->lock, flags); + + return 0; +} + +static int cygnus_gpio_get_strength(struct cygnus_gpio *chip, unsigned gpio, + u16 *strength) +{ + void __iomem *base; + unsigned int i, offset, shift; + u32 val; + unsigned long flags; + + if (chip->io_ctrl) { + base = chip->io_ctrl; + offset = CYGNUS_GPIO_DRV0_CTRL_OFFSET; + } else { + base = chip->base; + offset = CYGNUS_GPIO_REG(gpio, + CYGNUS_GPIO_ASIU_DRV0_CTRL_OFFSET); + } + + shift = CYGNUS_GPIO_SHIFT(gpio); + + spin_lock_irqsave(&chip->lock, flags); + *strength = 0; + for (i = 0; i < GPIO_DRV_STRENGTH_BITS; i++) { + val = readl(base + offset) & BIT(shift); + val >>= shift; + *strength += (val << i); + offset += 4; + } + + /* convert to mA */ + *strength = (*strength + 1) * 2; + spin_unlock_irqrestore(&chip->lock, flags); + + return 0; +} + +static int cygnus_pin_config_get(struct pinctrl_dev *pctldev, unsigned pin, + unsigned long *config) +{ + struct cygnus_gpio *chip = pinctrl_dev_get_drvdata(pctldev); + enum pin_config_param param = pinconf_to_config_param(*config); + unsigned gpio = cygnus_pin_to_gpio(pin); + u16 arg; + int disable, pull_up, ret; + + switch (param) { + case PIN_CONFIG_BIAS_DISABLE: + cygnus_gpio_get_pull(chip, gpio, &disable, &pull_up); + if (disable) + return 0; + else + return -EINVAL; + + case PIN_CONFIG_BIAS_PULL_UP: + cygnus_gpio_get_pull(chip, gpio, &disable, &pull_up); + if (!disable && pull_up) + return 0; + else + return -EINVAL; + + case PIN_CONFIG_BIAS_PULL_DOWN: + cygnus_gpio_get_pull(chip, gpio, &disable, &pull_up); + if (!disable && !pull_up) + return 0; + else + return -EINVAL; + + case PIN_CONFIG_DRIVE_STRENGTH: + ret = cygnus_gpio_get_strength(chip, gpio, &arg); + if (ret) + return ret; + else + *config = pinconf_to_config_packed(param, arg); + + return 0; + + default: + return -ENOTSUPP; + } + + return -ENOTSUPP; +} + +static int cygnus_pin_config_set(struct pinctrl_dev *pctldev, unsigned pin, + unsigned long *configs, unsigned num_configs) +{ + struct cygnus_gpio *chip = pinctrl_dev_get_drvdata(pctldev); + enum pin_config_param param; + u16 arg; + unsigned i, gpio = cygnus_pin_to_gpio(pin); + int ret = -ENOTSUPP; + + for (i = 0; i < num_configs; i++) { + param = pinconf_to_config_param(configs[i]); + arg = pinconf_to_config_argument(configs[i]); + + switch (param) { + case PIN_CONFIG_BIAS_DISABLE: + ret = cygnus_gpio_set_pull(chip, gpio, 1, 0); + if (ret < 0) + goto out; + break; + + case PIN_CONFIG_BIAS_PULL_UP: + ret = cygnus_gpio_set_pull(chip, gpio, 0, 1); + if (ret < 0) + goto out; + break; + + case PIN_CONFIG_BIAS_PULL_DOWN: + ret = cygnus_gpio_set_pull(chip, gpio, 0, 0); + if (ret < 0) + goto out; + break; + + case PIN_CONFIG_DRIVE_STRENGTH: + ret = cygnus_gpio_set_strength(chip, gpio, arg); + if (ret < 0) + goto out; + break; + + default: + dev_err(chip->dev, "invalid configuration\n"); + return -ENOTSUPP; + } + } /* for each config */ + +out: + return ret; +} + +static const struct pinconf_ops cygnus_pconf_ops = { + .is_generic = true, + .pin_config_get = cygnus_pin_config_get, + .pin_config_set = cygnus_pin_config_set, +}; + +/* + * Map a GPIO in the local gpio_chip pin space to a pin in the Cygnus IOMUX + * pinctrl pin space + */ +struct cygnus_gpio_pin_range { + unsigned offset; + unsigned pin_base; + unsigned num_pins; +}; + +#define CYGNUS_PINRANGE(o, p, n) { .offset = o, .pin_base = p, .num_pins = n } + +/* + * Pin mapping table for mapping local GPIO pins to Cygnus IOMUX pinctrl pins + */ +static const struct cygnus_gpio_pin_range cygnus_gpio_pintable[] = { + CYGNUS_PINRANGE(0, 42, 1), + CYGNUS_PINRANGE(1, 44, 3), + CYGNUS_PINRANGE(4, 48, 1), + CYGNUS_PINRANGE(5, 50, 3), + CYGNUS_PINRANGE(8, 126, 1), + CYGNUS_PINRANGE(9, 155, 1), + CYGNUS_PINRANGE(10, 152, 1), + CYGNUS_PINRANGE(11, 154, 1), + CYGNUS_PINRANGE(12, 153, 1), + CYGNUS_PINRANGE(13, 127, 3), + CYGNUS_PINRANGE(16, 140, 1), + CYGNUS_PINRANGE(17, 145, 7), + CYGNUS_PINRANGE(24, 130, 10), + CYGNUS_PINRANGE(34, 141, 4), + CYGNUS_PINRANGE(38, 54, 1), + CYGNUS_PINRANGE(39, 56, 3), + CYGNUS_PINRANGE(42, 60, 3), + CYGNUS_PINRANGE(45, 64, 3), + CYGNUS_PINRANGE(48, 68, 2), + CYGNUS_PINRANGE(50, 84, 6), + CYGNUS_PINRANGE(56, 94, 6), + CYGNUS_PINRANGE(62, 72, 1), + CYGNUS_PINRANGE(63, 70, 1), + CYGNUS_PINRANGE(64, 80, 1), + CYGNUS_PINRANGE(65, 74, 3), + CYGNUS_PINRANGE(68, 78, 1), + CYGNUS_PINRANGE(69, 82, 1), + CYGNUS_PINRANGE(70, 156, 17), + CYGNUS_PINRANGE(87, 104, 12), + CYGNUS_PINRANGE(99, 102, 2), + CYGNUS_PINRANGE(101, 90, 4), + CYGNUS_PINRANGE(105, 116, 10), + CYGNUS_PINRANGE(123, 11, 1), + CYGNUS_PINRANGE(124, 38, 4), + CYGNUS_PINRANGE(128, 43, 1), + CYGNUS_PINRANGE(129, 47, 1), + CYGNUS_PINRANGE(130, 49, 1), + CYGNUS_PINRANGE(131, 53, 1), + CYGNUS_PINRANGE(132, 55, 1), + CYGNUS_PINRANGE(133, 59, 1), + CYGNUS_PINRANGE(134, 63, 1), + CYGNUS_PINRANGE(135, 67, 1), + CYGNUS_PINRANGE(136, 71, 1), + CYGNUS_PINRANGE(137, 73, 1), + CYGNUS_PINRANGE(138, 77, 1), + CYGNUS_PINRANGE(139, 79, 1), + CYGNUS_PINRANGE(140, 81, 1), + CYGNUS_PINRANGE(141, 83, 1), + CYGNUS_PINRANGE(142, 10, 1) +}; + +/* + * The Cygnus IOMUX controller mainly supports group based mux configuration, + * but certain pins can be muxed to GPIO individually. Only the ASIU GPIO + * controller can support this, so it's an optional configuration + * + * Return -ENODEV means no support and that's fine + */ +static int cygnus_gpio_pinmux_add_range(struct cygnus_gpio *chip) +{ + struct device_node *node = chip->dev->of_node; + struct device_node *pinmux_node; + struct platform_device *pinmux_pdev; + struct gpio_chip *gc = &chip->gc; + int i, ret = 0; + + /* parse DT to find the phandle to the pinmux controller */ + pinmux_node = of_parse_phandle(node, "pinmux", 0); + if (!pinmux_node) + return -ENODEV; + + pinmux_pdev = of_find_device_by_node(pinmux_node); + /* no longer need the pinmux node */ + of_node_put(pinmux_node); + if (!pinmux_pdev) { + dev_err(chip->dev, "failed to get pinmux device\n"); + return -EINVAL; + } + + /* now need to create the mapping between local GPIO and PINMUX pins */ + for (i = 0; i < ARRAY_SIZE(cygnus_gpio_pintable); i++) { + ret = gpiochip_add_pin_range(gc, dev_name(&pinmux_pdev->dev), + cygnus_gpio_pintable[i].offset, + cygnus_gpio_pintable[i].pin_base, + cygnus_gpio_pintable[i].num_pins); + if (ret) { + dev_err(chip->dev, "unable to add GPIO pin range\n"); + goto err_put_device; + } + } + + chip->pinmux_is_supported = (ret == 0); + + /* no need for pinmux_pdev device reference anymore */ + put_device(&pinmux_pdev->dev); + return 0; + +err_put_device: + put_device(&pinmux_pdev->dev); + gpiochip_remove_pin_ranges(gc); + return ret; +} + +static void cygnus_gpio_pinmux_remove_range(struct cygnus_gpio *chip) +{ + struct gpio_chip *gc = &chip->gc; + + if (chip->pinmux_is_supported) + gpiochip_remove_pin_ranges(gc); +} + +/* + * Cygnus GPIO controller supports some PINCONF related configurations such as + * pull up, pull down, and drive strength, when the pin is configured to GPIO + * + * Here a local pinctrl device is created with simple 1-to-1 pin mapping to the + * local GPIO pins + */ +static int cygnus_gpio_register_pinconf(struct cygnus_gpio *chip) +{ + struct pinctrl_desc *pctldesc = &chip->pctldesc; + struct pinctrl_pin_desc *pins; + struct gpio_chip *gc = &chip->gc; + int i; + + pins = devm_kcalloc(chip->dev, gc->ngpio, sizeof(*pins), GFP_KERNEL); + if (!pins) + return -ENOMEM; + + for (i = 0; i < gc->ngpio; i++) { + pins[i].number = i; + pins[i].name = devm_kasprintf(chip->dev, GFP_KERNEL, + "gpio-%d", i); + if (!pins[i].name) + return -ENOMEM; + } + + pctldesc->name = dev_name(chip->dev); + pctldesc->pctlops = &cygnus_pctrl_ops; + pctldesc->pins = pins; + pctldesc->npins = gc->ngpio; + pctldesc->confops = &cygnus_pconf_ops; + + chip->pctl = pinctrl_register(pctldesc, chip->dev, chip); + if (!chip->pctl) { + dev_err(chip->dev, "unable to register pinctrl device\n"); + return -EINVAL; + } + + return 0; +} + +static void cygnus_gpio_unregister_pinconf(struct cygnus_gpio *chip) +{ + if (chip->pctl) + pinctrl_unregister(chip->pctl); +} + +static const struct of_device_id cygnus_gpio_of_match[] = { + { .compatible = "brcm,cygnus-gpio" }, + { } +}; +MODULE_DEVICE_TABLE(of, cygnus_gpio_of_match); + +static int cygnus_gpio_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct resource *res; + struct cygnus_gpio *chip; + struct gpio_chip *gc; + u32 ngpios; + int irq, ret; + + chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL); + if (!chip) + return -ENOMEM; + + chip->dev = dev; + platform_set_drvdata(pdev, chip); + + if (of_property_read_u32(dev->of_node, "ngpios", &ngpios)) { + dev_err(dev, "missing ngpios DT property\n"); + return -ENODEV; + } + chip->num_banks = (ngpios + NGPIOS_PER_BANK - 1) / NGPIOS_PER_BANK; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + chip->base = devm_ioremap_resource(dev, res); + if (IS_ERR(chip->base)) { + dev_err(dev, "unable to map I/O memory\n"); + return PTR_ERR(chip->base); + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); + if (res) { + chip->io_ctrl = devm_ioremap_resource(dev, res); + if (IS_ERR(chip->io_ctrl)) { + dev_err(dev, "unable to map I/O memory\n"); + return PTR_ERR(chip->io_ctrl); + } + } + + spin_lock_init(&chip->lock); + + gc = &chip->gc; + gc->base = -1; + gc->ngpio = ngpios; + gc->label = dev_name(dev); + gc->dev = dev; + gc->of_node = dev->of_node; + gc->request = cygnus_gpio_request; + gc->free = cygnus_gpio_free; + gc->direction_input = cygnus_gpio_direction_input; + gc->direction_output = cygnus_gpio_direction_output; + gc->set = cygnus_gpio_set; + gc->get = cygnus_gpio_get; + + ret = gpiochip_add(gc); + if (ret < 0) { + dev_err(dev, "unable to add GPIO chip\n"); + return ret; + } + + ret = cygnus_gpio_pinmux_add_range(chip); + if (ret && ret != -ENODEV) { + dev_err(dev, "unable to add GPIO pin range\n"); + goto err_rm_gpiochip; + } + + ret = cygnus_gpio_register_pinconf(chip); + if (ret) { + dev_err(dev, "unable to register pinconf\n"); + goto err_rm_range; + } + + /* optional GPIO interrupt support */ + irq = platform_get_irq(pdev, 0); + if (irq) { + ret = gpiochip_irqchip_add(gc, &cygnus_gpio_irq_chip, 0, + handle_simple_irq, IRQ_TYPE_NONE); + if (ret) { + dev_err(dev, "no GPIO irqchip\n"); + goto err_unregister_pinconf; + } + + gpiochip_set_chained_irqchip(gc, &cygnus_gpio_irq_chip, irq, + cygnus_gpio_irq_handler); + } + + return 0; + +err_unregister_pinconf: + cygnus_gpio_unregister_pinconf(chip); + +err_rm_range: + cygnus_gpio_pinmux_remove_range(chip); + +err_rm_gpiochip: + gpiochip_remove(gc); + + return ret; +} + +static struct platform_driver cygnus_gpio_driver = { + .driver = { + .name = "cygnus-gpio", + .of_match_table = cygnus_gpio_of_match, + }, + .probe = cygnus_gpio_probe, +}; + +static int __init cygnus_gpio_init(void) +{ + return platform_driver_probe(&cygnus_gpio_driver, cygnus_gpio_probe); +} +arch_initcall_sync(cygnus_gpio_init); + +MODULE_AUTHOR("Ray Jui "); +MODULE_DESCRIPTION("Broadcom Cygnus GPIO Driver"); +MODULE_LICENSE("GPL v2"); -- 1.7.9.5 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/