Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S932354AbbBZTBt (ORCPT ); Thu, 26 Feb 2015 14:01:49 -0500 Received: from foss.arm.com ([217.140.101.70]:41754 "EHLO foss.arm.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S932213AbbBZTBo (ORCPT ); Thu, 26 Feb 2015 14:01:44 -0500 From: Javi Merino To: edubezval@gmail.com, rui.zhang@intel.com Cc: linux-pm@vger.kernel.org, linux-kernel@vger.kernel.org, punit.agrawal@arm.com, broonie@kernel.org, tixy@linaro.org, Javi Merino Subject: [PATCH v2 4/7] thermal: introduce the Power Allocator governor Date: Thu, 26 Feb 2015 19:00:30 +0000 Message-Id: <1424977233-15965-5-git-send-email-javi.merino@arm.com> X-Mailer: git-send-email 1.9.1 In-Reply-To: <1424977233-15965-1-git-send-email-javi.merino@arm.com> References: <1424977233-15965-1-git-send-email-javi.merino@arm.com> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 34362 Lines: 997 The power allocator governor is a thermal governor that controls system and device power allocation to control temperature. Conceptually, the implementation divides the sustainable power of a thermal zone among all the heat sources in that zone. This governor relies on "power actors", entities that represent heat sources. They can report current and maximum power consumption and can set a given maximum power consumption, usually via a cooling device. The governor uses a Proportional Integral Derivative (PID) controller driven by the temperature of the thermal zone. The output of the controller is a power budget that is then allocated to each power actor that can have bearing on the temperature we are trying to control. It decides how much power to give each cooling device based on the performance they are requesting. The PID controller ensures that the total power budget does not exceed the control temperature. Cc: Zhang Rui Cc: Eduardo Valentin Signed-off-by: Punit Agrawal Signed-off-by: Javi Merino --- Documentation/thermal/power_allocator.txt | 247 ++++++++++++++ drivers/thermal/Kconfig | 15 + drivers/thermal/Makefile | 1 + drivers/thermal/power_allocator.c | 515 ++++++++++++++++++++++++++++++ drivers/thermal/thermal_core.c | 9 +- drivers/thermal/thermal_core.h | 8 + include/linux/thermal.h | 37 ++- 7 files changed, 825 insertions(+), 7 deletions(-) create mode 100644 Documentation/thermal/power_allocator.txt create mode 100644 drivers/thermal/power_allocator.c diff --git a/Documentation/thermal/power_allocator.txt b/Documentation/thermal/power_allocator.txt new file mode 100644 index 000000000000..c3797b529991 --- /dev/null +++ b/Documentation/thermal/power_allocator.txt @@ -0,0 +1,247 @@ +Power allocator governor tunables +================================= + +Trip points +----------- + +The governor requires the following two passive trip points: + +1. "switch on" trip point: temperature above which the governor + control loop starts operating. This is the first passive trip + point of the thermal zone. + +2. "desired temperature" trip point: it should be higher than the + "switch on" trip point. This the target temperature the governor + is controlling for. This is the last passive trip point of the + thermal zone. + +PID Controller +-------------- + +The power allocator governor implements a +Proportional-Integral-Derivative controller (PID controller) with +temperature as the control input and power as the controlled output: + + P_max = k_p * e + k_i * err_integral + k_d * diff_err + sustainable_power + +where + e = desired_temperature - current_temperature + err_integral is the sum of previous errors + diff_err = e - previous_error + +It is similar to the one depicted below: + + k_d + | +current_temp | + | v + | +----------+ +---+ + | +----->| diff_err |-->| X |------+ + | | +----------+ +---+ | + | | | tdp actor + | | k_i | | get_requested_power() + | | | | | | | + | | | | | | | ... + v | v v v v v + +---+ | +-------+ +---+ +---+ +---+ +----------+ + | S |-------+----->| sum e |----->| X |--->| S |-->| S |-->|power | + +---+ | +-------+ +---+ +---+ +---+ |allocation| + ^ | ^ +----------+ + | | | | | + | | +---+ | | | + | +------->| X |-------------------+ v v + | +---+ granted performance +desired_temperature ^ + | + | + k_po/k_pu + +Sustainable power +----------------- + +An estimate of the sustainable dissipatable power (in mW) should be +provided while registering the thermal zone. This estimates the +sustained power that can be dissipated at the desired control +temperature. This is the maximum sustained power for allocation at +the desired maximum temperature. The actual sustained power can vary +for a number of reasons. The closed loop controller will take care of +variations such as environmental conditions, and some factors related +to the speed-grade of the silicon. `sustainable_power` is therefore +simply an estimate, and may be tuned to affect the aggressiveness of +the thermal ramp. For reference, the sustainable power of a 4" phone +is typically 2000mW, while on a 10" tablet is around 4500mW (may vary +depending on screen size). + +If you are using device tree, do add it as a property of the +thermal-zone. For example: + + thermal-zones { + soc_thermal { + polling-delay = <1000>; + polling-delay-passive = <100>; + sustainable-power = <2500>; + ... + +Instead, if the thermal zone is registered from the platform code, pass a +`thermal_zone_params` that has a `sustainable_power`. If no +`thermal_zone_params` were being passed, then something like below +will suffice: + + static const struct thermal_zone_params tz_params = { + .sustainable_power = 3500, + }; + +and then pass `tz_params` as the 5th parameter to +`thermal_zone_device_register()` + +k_po and k_pu +------------- + +The implementation of the PID controller in the power allocator +thermal governor allows the configuration of two proportional term +constants: `k_po` and `k_pu`. `k_po` is the proportional term +constant during temperature overshoot periods (current temperature is +above "desired temperature" trip point). Conversely, `k_pu` is the +proportional term constant during temperature undershoot periods +(current temperature below "desired temperature" trip point). + +These controls are intended as the primary mechanism for configuring +the permitted thermal "ramp" of the system. For instance, a lower +`k_pu` value will provide a slower ramp, at the cost of capping +available capacity at a low temperature. On the other hand, a high +value of `k_pu` will result in the governor granting very high power +whilst temperature is low, and may lead to temperature overshooting. + +The default value for `k_pu` is: + + 2 * sustainable_power / (desired_temperature - switch_on_temp) + +This means that at `switch_on_temp` the output of the controller's +proportional term will be 2 * `sustainable_power`. The default value +for `k_po` is: + + sustainable_power / (desired_temperature - switch_on_temp) + +Focusing on the proportional and feed forward values of the PID +controller equation we have: + + P_max = k_p * e + sustainable_power + +The proportional term is proportional to the difference between the +desired temperature and the current one. When the current temperature +is the desired one, then the proportional component is zero and +`P_max` = `sustainable_power`. That is, the system should operate in +thermal equilibrium under constant load. `sustainable_power` is only +an estimate, which is the reason for closed-loop control such as this. + +Expanding `k_pu` we get: + P_max = 2 * sustainable_power * (T_set - T) / (T_set - T_on) + + sustainable_power + +where + T_set is the desired temperature + T is the current temperature + T_on is the switch on temperature + +When the current temperature is the switch_on temperature, the above +formula becomes: + + P_max = 2 * sustainable_power * (T_set - T_on) / (T_set - T_on) + + sustainable_power = 2 * sustainable_power + sustainable_power = + 3 * sustainable_power + +Therefore, the proportional term alone linearly decreases power from +3 * `sustainable_power` to `sustainable_power` as the temperature +rises from the switch on temperature to the desired temperature. + +k_i and integral_cutoff +----------------------- + +`k_i` configures the PID loop's integral term constant. This term +allows the PID controller to compensate for long term drift and for +the quantized nature of the output control: cooling devices can't set +the exact power that the governor requests. When the temperature +error is below `integral_cutoff`, errors are accumulated in the +integral term. This term is then multiplied by `k_i` and the result +added to the output of the controller. Typically `k_i` is set low (1 +or 2) and `integral_cutoff` is 0. + +k_d +--- + +`k_d` configures the PID loop's derivative term constant. It's +recommended to leave it as the default: 0. + +Cooling device power API +======================== + +Cooling devices controlled by this governor must supply the additional +"power" API in their `cooling_device_ops`. It consists on three ops: + +1. int get_requested_power(struct thermal_cooling_device *cdev, + struct thermal_zone_device *tz, u32 *power); +@cdev: The `struct thermal_cooling_device` pointer +@tz: thermal zone in which we are currently operating +@power: pointer in which to store the calculated power + +`get_requested_power()` calculates the power requested by the device +in milliwatts and stores it in @power . It should return 0 on +success, -E* on failure. This is currently used by the power +allocator governor to calculate how much power to give to each cooling +device. + +2. int state2power(struct thermal_cooling_device *cdev, struct + thermal_zone_device *tz, unsigned long state, u32 *power); +@cdev: The `struct thermal_cooling_device` pointer +@tz: thermal zone in which we are currently operating +@state: A cooling device state +@power: pointer in which to store the equivalent power + +Convert cooling device state @state into power consumption in +milliwatts and store it in @power. It should return 0 on success, -E* +on failure. This is currently used by thermal core to calculate the +maximum power that an actor can consume. + +3. int power2state(struct thermal_cooling_device *cdev, u32 power, + unsigned long *state); +@cdev: The `struct thermal_cooling_device` pointer +@power: power in milliwatts +@state: pointer in which to store the resulting state + +Calculate a cooling device state that would make the device consume at +most @power mW and store it in @state. It should return 0 on success, +-E* on failure. This is currently used by the thermal core to convert +a given power set by the power allocator governor to a state that the +cooling device can set. It is a function because this conversion may +depend on external factors that may change so this function should the +best conversion given "current circumstances". + +Cooling device weights +---------------------- + +Weights are a mechanism to bias the allocation among cooling +devices. They express the relative power efficiency of different +cooling devices. Higher weight can be used to express higher power +efficiency. Weighting is relative such that if each cooling device +has a weight of one they are considered equal. This is particularly +useful in heterogeneous systems where two cooling devices may perform +the same kind of compute, but with different efficiency. For example, +a system with two different types of processors. + +If the thermal zone is registered using +`thermal_zone_device_register()` (i.e., platform code), then weights +are passed as part of the thermal zone's `thermal_bind_parameters`. +If the platform is registered using device tree, then they are passed +as the `contribution` property of each map in the `cooling-maps` node. + +Limitations of the power allocator governor +=========================================== + +The power allocator governor's PID controller works best if there is a +periodic tick. If you have a driver that calls +`thermal_zone_device_update()` (or anything that ends up calling the +governor's `throttle()` function) repetitively, the governor response +won't be very good. Note that this is not particular to this +governor, step-wise will also misbehave if you call its throttle() +faster than the normal thermal framework tick (due to interrupts for +example) as it will overreact. diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig index 30aee81e9f5b..a1b43eab0a70 100644 --- a/drivers/thermal/Kconfig +++ b/drivers/thermal/Kconfig @@ -71,6 +71,14 @@ config THERMAL_DEFAULT_GOV_USER_SPACE Select this if you want to let the user space manage the platform thermals. +config THERMAL_DEFAULT_GOV_POWER_ALLOCATOR + bool "power_allocator" + select THERMAL_GOV_POWER_ALLOCATOR + help + Select this if you want to control temperature based on + system and device power allocation. This governor can only + operate on cooling devices that implement the power API. + endchoice config THERMAL_GOV_FAIR_SHARE @@ -99,6 +107,13 @@ config THERMAL_GOV_USER_SPACE help Enable this to let the user space manage the platform thermals. +config THERMAL_GOV_POWER_ALLOCATOR + bool "Power allocator thermal governor" + select THERMAL_POWER_ACTOR + help + Enable this to manage platform thermals by dynamically + allocating and limiting power to devices. + config CPU_THERMAL bool "generic cpu cooling support" depends on CPU_FREQ diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile index 1fe86652cfb6..b1783cf37ed2 100644 --- a/drivers/thermal/Makefile +++ b/drivers/thermal/Makefile @@ -14,6 +14,7 @@ thermal_sys-$(CONFIG_THERMAL_GOV_FAIR_SHARE) += fair_share.o thermal_sys-$(CONFIG_THERMAL_GOV_BANG_BANG) += gov_bang_bang.o thermal_sys-$(CONFIG_THERMAL_GOV_STEP_WISE) += step_wise.o thermal_sys-$(CONFIG_THERMAL_GOV_USER_SPACE) += user_space.o +thermal_sys-$(CONFIG_THERMAL_GOV_POWER_ALLOCATOR) += power_allocator.o # cpufreq cooling thermal_sys-$(CONFIG_CPU_THERMAL) += cpu_cooling.o diff --git a/drivers/thermal/power_allocator.c b/drivers/thermal/power_allocator.c new file mode 100644 index 000000000000..bfea8d35c0a2 --- /dev/null +++ b/drivers/thermal/power_allocator.c @@ -0,0 +1,515 @@ +/* + * A power allocator to manage temperature + * + * Copyright (C) 2014 ARM Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#define pr_fmt(fmt) "Power allocator: " fmt + +#include +#include +#include + +#include "thermal_core.h" + +#define FRAC_BITS 10 +#define int_to_frac(x) ((x) << FRAC_BITS) +#define frac_to_int(x) ((x) >> FRAC_BITS) + +/** + * mul_frac() - multiply two fixed-point numbers + * @x: first multiplicand + * @y: second multiplicand + * + * Return: the result of multiplying two fixed-point numbers. The + * result is also a fixed-point number. + */ +static inline s64 mul_frac(s64 x, s64 y) +{ + return (x * y) >> FRAC_BITS; +} + +/** + * div_frac() - divide two fixed-point numbers + * @x: the dividend + * @y: the divisor + * + * Return: the result of dividing two fixed-point numbers. The + * result is also a fixed-point number. + */ +static inline s64 div_frac(s64 x, s64 y) +{ + return div_s64(x << FRAC_BITS, y); +} + +/** + * struct power_allocator_params - parameters for the power allocator governor + * @err_integral: accumulated error in the PID controller. + * @prev_err: error in the previous iteration of the PID controller. + * Used to calculate the derivative term. + * @trip_switch_on: first passive trip point of the thermal zone. The + * governor switches on when this trip point is crossed. + * @trip_max_desired_temperature: last passive trip point of the thermal + * zone. The temperature we are + * controlling for. + */ +struct power_allocator_params { + s64 err_integral; + s32 prev_err; + int trip_switch_on; + int trip_max_desired_temperature; +}; + +/** + * pid_controller() - PID controller + * @tz: thermal zone we are operating in + * @current_temp: the current temperature in millicelsius + * @control_temp: the target temperature in millicelsius + * @max_allocatable_power: maximum allocatable power for this thermal zone + * + * This PID controller increases the available power budget so that the + * temperature of the thermal zone gets as close as possible to + * @control_temp and limits the power if it exceeds it. k_po is the + * proportional term when we are overshooting, k_pu is the + * proportional term when we are undershooting. integral_cutoff is a + * threshold below which we stop accumulating the error. The + * accumulated error is only valid if the requested power will make + * the system warmer. If the system is mostly idle, there's no point + * in accumulating positive error. + * + * Return: The power budget for the next period. + */ +static u32 pid_controller(struct thermal_zone_device *tz, + unsigned long current_temp, + unsigned long control_temp, + u32 max_allocatable_power) +{ + s64 p, i, d, power_range; + s32 err, max_power_frac; + struct power_allocator_params *params = tz->governor_data; + + max_power_frac = int_to_frac(max_allocatable_power); + + err = ((s32)control_temp - (s32)current_temp); + err = int_to_frac(err); + + /* Calculate the proportional term */ + p = mul_frac(err < 0 ? tz->tzp->k_po : tz->tzp->k_pu, err); + + /* + * Calculate the integral term + * + * if the error is less than cut off allow integration (but + * the integral is limited to max power) + */ + i = mul_frac(tz->tzp->k_i, params->err_integral); + + if (err < int_to_frac(tz->tzp->integral_cutoff)) { + s64 i_next = i + mul_frac(tz->tzp->k_i, err); + + if (abs64(i_next) < max_power_frac) { + i = i_next; + params->err_integral += err; + } + } + + /* + * Calculate the derivative term + * + * We do err - prev_err, so with a positive k_d, a decreasing + * error (i.e. driving closer to the line) results in less + * power being applied, slowing down the controller) + */ + d = mul_frac(tz->tzp->k_d, err - params->prev_err); + d = div_frac(d, tz->passive_delay); + params->prev_err = err; + + power_range = p + i + d; + + /* feed-forward the known sustainable dissipatable power */ + power_range = tz->tzp->sustainable_power + frac_to_int(power_range); + + return clamp(power_range, (s64)0, (s64)max_allocatable_power); +} + +/** + * divvy_up_power() - divvy the allocated power between the actors + * @req_power: each actor's requested power + * @max_power: each actor's maximum available power + * @num_actors: size of the @req_power, @max_power and @granted_power's array + * @total_req_power: sum of @req_power + * @power_range: total allocated power + * @granted_power: output array: each actor's granted power + * + * This function divides the total allocated power (@power_range) + * fairly between the actors. It first tries to give each actor a + * share of the @power_range according to how much power it requested + * compared to the rest of the actors. For example, if only one actor + * requests power, then it receives all the @power_range. If + * three actors each requests 1mW, each receives a third of the + * @power_range. + * + * If any actor received more than their maximum power, then that + * surplus is re-divvied among the actors based on how far they are + * from their respective maximums. + * + * Granted power for each actor is written to @granted_power, which + * should've been allocated by the calling function. + */ +static void divvy_up_power(u32 *req_power, u32 *max_power, int num_actors, + u32 total_req_power, u32 power_range, + u32 *granted_power) +{ + u32 extra_power, capped_extra_power, extra_actor_power[num_actors]; + int i; + + /* + * Prevent division by 0 if none of the actors request power. + */ + if (!total_req_power) + total_req_power = 1; + + capped_extra_power = 0; + extra_power = 0; + for (i = 0; i < num_actors; i++) { + u64 req_range = req_power[i] * power_range; + + granted_power[i] = div_u64(req_range, total_req_power); + + if (granted_power[i] > max_power[i]) { + extra_power += granted_power[i] - max_power[i]; + granted_power[i] = max_power[i]; + } + + extra_actor_power[i] = max_power[i] - granted_power[i]; + capped_extra_power += extra_actor_power[i]; + } + + if (!extra_power) + return; + + /* + * Re-divvy the reclaimed extra among actors based on + * how far they are from the max + */ + extra_power = min(extra_power, capped_extra_power); + if (capped_extra_power > 0) + for (i = 0; i < num_actors; i++) + granted_power[i] += (extra_actor_power[i] * + extra_power) / capped_extra_power; +} + +static int allocate_power(struct thermal_zone_device *tz, + unsigned long current_temp, + unsigned long control_temp) +{ + struct thermal_instance *instance; + struct power_allocator_params *params = tz->governor_data; + u32 *req_power, *max_power, *granted_power; + u32 total_req_power, max_allocatable_power; + u32 power_range; + int i, num_actors, total_weight, ret = 0; + int trip_max_desired_temperature = params->trip_max_desired_temperature; + + mutex_lock(&tz->lock); + + num_actors = 0; + total_weight = 0; + list_for_each_entry(instance, &tz->thermal_instances, tz_node) { + if ((instance->trip == trip_max_desired_temperature) && + cdev_is_power_actor(instance->cdev)) { + num_actors++; + total_weight += instance->weight; + } + } + + /* + * We need to allocate three arrays of the same size: + * req_power, max_power and granted_power. They are going to + * be needed until this function returns. Allocate them all + * in one go to simplify the allocation and deallocation + * logic. + */ + BUILD_BUG_ON(sizeof(*req_power) != sizeof(*max_power)); + BUILD_BUG_ON(sizeof(*req_power) != sizeof(*granted_power)); + req_power = devm_kcalloc(&tz->device, num_actors * 3, + sizeof(*req_power), GFP_KERNEL); + if (!req_power) { + ret = -ENOMEM; + goto unlock; + } + + max_power = &req_power[num_actors]; + granted_power = &req_power[2 * num_actors]; + + i = 0; + total_req_power = 0; + max_allocatable_power = 0; + + list_for_each_entry(instance, &tz->thermal_instances, tz_node) { + int weight; + struct thermal_cooling_device *cdev = instance->cdev; + + if (instance->trip != trip_max_desired_temperature) + continue; + + if (!cdev_is_power_actor(cdev)) + continue; + + if (cdev->ops->get_requested_power(cdev, tz, &req_power[i])) + continue; + + if (!total_weight) + weight = 1 << FRAC_BITS; + else + weight = instance->weight; + + req_power[i] = frac_to_int(weight * req_power[i]); + + if (power_actor_get_max_power(cdev, tz, &max_power[i])) + continue; + + total_req_power += req_power[i]; + max_allocatable_power += max_power[i]; + + i++; + } + + power_range = pid_controller(tz, current_temp, control_temp, + max_allocatable_power); + + divvy_up_power(req_power, max_power, num_actors, total_req_power, + power_range, granted_power); + + i = 0; + list_for_each_entry(instance, &tz->thermal_instances, tz_node) { + if (instance->trip != trip_max_desired_temperature) + continue; + + if (!cdev_is_power_actor(instance->cdev)) + continue; + + power_actor_set_power(instance->cdev, instance, + granted_power[i]); + + i++; + } + + devm_kfree(&tz->device, req_power); +unlock: + mutex_unlock(&tz->lock); + + return ret; +} + +static int get_governor_trips(struct thermal_zone_device *tz, + struct power_allocator_params *params) +{ + int i, ret, last_passive; + bool found_first_passive; + + found_first_passive = false; + last_passive = -1; + ret = -EINVAL; + + for (i = 0; i < tz->trips; i++) { + enum thermal_trip_type type; + + ret = tz->ops->get_trip_type(tz, i, &type); + if (ret) + return ret; + + if (!found_first_passive) { + if (type == THERMAL_TRIP_PASSIVE) { + params->trip_switch_on = i; + found_first_passive = true; + } + } else if (type == THERMAL_TRIP_PASSIVE) { + last_passive = i; + } else { + break; + } + } + + if (last_passive != -1) { + params->trip_max_desired_temperature = last_passive; + ret = 0; + } else { + ret = -EINVAL; + } + + return ret; +} + +static void reset_pid_controller(struct power_allocator_params *params) +{ + params->err_integral = 0; + params->prev_err = 0; +} + +static void allow_maximum_power(struct thermal_zone_device *tz) +{ + struct thermal_instance *instance; + struct power_allocator_params *params = tz->governor_data; + + list_for_each_entry(instance, &tz->thermal_instances, tz_node) { + if ((instance->trip != params->trip_max_desired_temperature) || + (!cdev_is_power_actor(instance->cdev))) + continue; + + instance->target = 0; + instance->cdev->updated = false; + thermal_cdev_update(instance->cdev); + } +} + +/** + * power_allocator_bind() - bind the power_allocator governor to a thermal zone + * @tz: thermal zone to bind it to + * + * Check that the thermal zone is valid for this governor, that is, it + * has two thermal trips. If so, initialize the PID controller + * parameters and bind it to the thermal zone. + * + * Return: 0 on success, -EINVAL if the trips were invalid or -ENOMEM + * if we ran out of memory. + */ +static int power_allocator_bind(struct thermal_zone_device *tz) +{ + int ret; + struct power_allocator_params *params; + unsigned long switch_on_temp, control_temp; + u32 temperature_threshold; + + if (!tz->tzp || !tz->tzp->sustainable_power) { + dev_err(&tz->device, + "power_allocator: missing sustainable_power\n"); + return -EINVAL; + } + + params = devm_kzalloc(&tz->device, sizeof(*params), GFP_KERNEL); + if (!params) + return -ENOMEM; + + ret = get_governor_trips(tz, params); + if (ret) { + dev_err(&tz->device, + "thermal zone %s has wrong trip setup for power allocator\n", + tz->type); + goto free; + } + + ret = tz->ops->get_trip_temp(tz, params->trip_switch_on, + &switch_on_temp); + if (ret) + goto free; + + ret = tz->ops->get_trip_temp(tz, params->trip_max_desired_temperature, + &control_temp); + if (ret) + goto free; + + temperature_threshold = control_temp - switch_on_temp; + + tz->tzp->k_po = tz->tzp->k_po ?: + int_to_frac(tz->tzp->sustainable_power) / temperature_threshold; + tz->tzp->k_pu = tz->tzp->k_pu ?: + int_to_frac(2 * tz->tzp->sustainable_power) / + temperature_threshold; + tz->tzp->k_i = tz->tzp->k_i ?: int_to_frac(10) / 1000; + /* + * The default for k_d and integral_cutoff is 0, so we can + * leave them as they are. + */ + + reset_pid_controller(params); + + tz->governor_data = params; + + return 0; + +free: + devm_kfree(&tz->device, params); + return ret; +} + +static void power_allocator_unbind(struct thermal_zone_device *tz) +{ + dev_dbg(&tz->device, "Unbinding from thermal zone %d\n", tz->id); + devm_kfree(&tz->device, tz->governor_data); + tz->governor_data = NULL; +} + +static int power_allocator_throttle(struct thermal_zone_device *tz, int trip) +{ + int ret; + unsigned long switch_on_temp, control_temp, current_temp; + struct power_allocator_params *params = tz->governor_data; + + /* + * We get called for every trip point but we only need to do + * our calculations once + */ + if (trip != params->trip_max_desired_temperature) + return 0; + + ret = thermal_zone_get_temp(tz, ¤t_temp); + if (ret) { + dev_warn(&tz->device, "Failed to get temperature: %d\n", ret); + return ret; + } + + ret = tz->ops->get_trip_temp(tz, params->trip_switch_on, + &switch_on_temp); + if (ret) { + dev_warn(&tz->device, + "Failed to get switch on temperature: %d\n", ret); + return ret; + } + + if (current_temp < switch_on_temp) { + tz->passive = 0; + reset_pid_controller(params); + allow_maximum_power(tz); + return 0; + } + + tz->passive = 1; + + ret = tz->ops->get_trip_temp(tz, params->trip_max_desired_temperature, + &control_temp); + if (ret) { + dev_warn(&tz->device, + "Failed to get the maximum desired temperature: %d\n", + ret); + return ret; + } + + return allocate_power(tz, current_temp, control_temp); +} + +static struct thermal_governor thermal_gov_power_allocator = { + .name = "power_allocator", + .bind_to_tz = power_allocator_bind, + .unbind_from_tz = power_allocator_unbind, + .throttle = power_allocator_throttle, +}; + +int thermal_gov_power_allocator_register(void) +{ + return thermal_register_governor(&thermal_gov_power_allocator); +} + +void thermal_gov_power_allocator_unregister(void) +{ + thermal_unregister_governor(&thermal_gov_power_allocator); +} diff --git a/drivers/thermal/thermal_core.c b/drivers/thermal/thermal_core.c index 82f1cca9c8ce..df9ba3bf55dc 100644 --- a/drivers/thermal/thermal_core.c +++ b/drivers/thermal/thermal_core.c @@ -1617,7 +1617,7 @@ static void remove_trip_attrs(struct thermal_zone_device *tz) struct thermal_zone_device *thermal_zone_device_register(const char *type, int trips, int mask, void *devdata, struct thermal_zone_device_ops *ops, - const struct thermal_zone_params *tzp, + struct thermal_zone_params *tzp, int passive_delay, int polling_delay) { struct thermal_zone_device *tz; @@ -1969,7 +1969,11 @@ static int __init thermal_register_governors(void) if (result) return result; - return thermal_gov_user_space_register(); + result = thermal_gov_user_space_register(); + if (result) + return result; + + return thermal_gov_power_allocator_register(); } static void thermal_unregister_governors(void) @@ -1978,6 +1982,7 @@ static void thermal_unregister_governors(void) thermal_gov_fair_share_unregister(); thermal_gov_bang_bang_unregister(); thermal_gov_user_space_unregister(); + thermal_gov_power_allocator_unregister(); } static int __init thermal_init(void) diff --git a/drivers/thermal/thermal_core.h b/drivers/thermal/thermal_core.h index faebe881f062..8a6624488cc5 100644 --- a/drivers/thermal/thermal_core.h +++ b/drivers/thermal/thermal_core.h @@ -88,6 +88,14 @@ static inline int thermal_gov_user_space_register(void) { return 0; } static inline void thermal_gov_user_space_unregister(void) {} #endif /* CONFIG_THERMAL_GOV_USER_SPACE */ +#ifdef CONFIG_THERMAL_GOV_POWER_ALLOCATOR +int thermal_gov_power_allocator_register(void); +void thermal_gov_power_allocator_unregister(void); +#else +static inline int thermal_gov_power_allocator_register(void) { return 0; } +static inline void thermal_gov_power_allocator_unregister(void) {} +#endif /* CONFIG_THERMAL_GOV_POWER_ALLOCATOR */ + /* device tree support */ #ifdef CONFIG_THERMAL_OF int of_parse_thermal_zones(void); diff --git a/include/linux/thermal.h b/include/linux/thermal.h index d69b1806f430..f8f503cd50a6 100644 --- a/include/linux/thermal.h +++ b/include/linux/thermal.h @@ -59,6 +59,8 @@ #define DEFAULT_THERMAL_GOVERNOR "fair_share" #elif defined(CONFIG_THERMAL_DEFAULT_GOV_USER_SPACE) #define DEFAULT_THERMAL_GOVERNOR "user_space" +#elif defined(CONFIG_THERMAL_DEFAULT_GOV_POWER_ALLOCATOR) +#define DEFAULT_THERMAL_GOVERNOR "power_allocator" #endif struct thermal_zone_device; @@ -154,8 +156,7 @@ struct thermal_attr { * @devdata: private pointer for device private data * @trips: number of trip points the thermal zone supports * @passive_delay: number of milliseconds to wait between polls when - * performing passive cooling. Currenty only used by the - * step-wise governor + * performing passive cooling. * @polling_delay: number of milliseconds to wait between polls when * checking whether trip points have been crossed (0 for * interrupt driven systems) @@ -165,7 +166,6 @@ struct thermal_attr { * @last_temperature: previous temperature read * @emul_temperature: emulated temperature when using CONFIG_THERMAL_EMULATION * @passive: 1 if you've crossed a passive trip point, 0 otherwise. - * Currenty only used by the step-wise governor. * @forced_passive: If > 0, temperature at which to switch on all ACPI * processor cooling devices. Currently only used by the * step-wise governor. @@ -197,7 +197,7 @@ struct thermal_zone_device { int passive; unsigned int forced_passive; struct thermal_zone_device_ops *ops; - const struct thermal_zone_params *tzp; + struct thermal_zone_params *tzp; struct thermal_governor *governor; void *governor_data; struct list_head thermal_instances; @@ -275,6 +275,33 @@ struct thermal_zone_params { int num_tbps; /* Number of tbp entries */ struct thermal_bind_params *tbp; + + /* + * Sustainable power (heat) that this thermal zone can dissipate in + * mW + */ + u32 sustainable_power; + + /* + * Proportional parameter of the PID controller when + * overshooting (i.e., when temperature is below the target) + */ + s32 k_po; + + /* + * Proportional parameter of the PID controller when + * undershooting + */ + s32 k_pu; + + /* Integral parameter of the PID controller */ + s32 k_i; + + /* Derivative parameter of the PID controller */ + s32 k_d; + + /* threshold below which the error is no longer accumulated */ + s32 integral_cutoff; }; struct thermal_genl_event { @@ -349,7 +376,7 @@ int power_actor_set_power(struct thermal_cooling_device *, struct thermal_instance *, u32); struct thermal_zone_device *thermal_zone_device_register(const char *, int, int, void *, struct thermal_zone_device_ops *, - const struct thermal_zone_params *, int, int); + struct thermal_zone_params *, int, int); void thermal_zone_device_unregister(struct thermal_zone_device *); int thermal_zone_bind_cooling_device(struct thermal_zone_device *, int, -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/