Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1754768AbbFKQUH (ORCPT ); Thu, 11 Jun 2015 12:20:07 -0400 Received: from eusmtp01.atmel.com ([212.144.249.242]:10083 "EHLO eusmtp01.atmel.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752741AbbFKQUC (ORCPT ); Thu, 11 Jun 2015 12:20:02 -0400 From: Cyrille Pitchen To: , , , , , , , CC: , , , , , , , , Cyrille Pitchen Subject: [PATCH linux-next v2 0/4] tty/serial: at91: add support to FIFOs Date: Thu, 11 Jun 2015 18:20:13 +0200 Message-ID: X-Mailer: git-send-email 1.8.2.2 MIME-Version: 1.0 Content-Type: text/plain Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 2772 Lines: 57 ChangeLog v2: - remove "atmel,rts-high-threshold" and "atmel,rts-low-threshold" from new DT properties. For now these two thresholds are set once for all during the probe but a later patch might allow to configure them at run time. - reword the commit message of the DT property patch to better explain why we have chosen to introduce the new property "atmel,fifo-size". - add a missing chunk in the FIFO patch: as the commit message explains, we need to use 8bit accesses when dealing with the Transmit/Receive Holding Registers. v1: This series of patches add support to FIFOs which will be introduced with Atmel sama5d2x SoC. FIFOs allow to reduce the number of I/O access. Indeed depending on the data size and the USART mode, FIFOs work in either single or multiple data. For multiple data, up to 4 data can be written into the Transmit Holding Register or read from the Receive Holding Register in a single word access. Also the RX FIFO allows to reduce the risk of receive overrun and data loss, especially when the DMA controller is not used. Finally, when the hardware handshake mode is selected, the RTS line can now be controlled by two thresholds on the RX FIFO. When FIFO level (the number of data available to be read) crosses the high threshold, the RTS line is set to high level telling the peer that it should stop sending new data. Data are read from the RX FIFO and when the FIFO level crosses the low threshold, the RTS is set back to low level telling the remote peer that it can send data again. This new feature resolves a long time hardware limitation where the RTS line was directly controlled by a PDC signal. There is no equivalent of that signal for the DMA controller so for all SoCs without PDC for USART there was no mean to control the RTS line properly: once the hardware handshake mode selected, the RTS line remains high level. Next SoCs with FIFOs will be able to use the hardware handshake mode thanks to the RX FIFO. Cyrille Pitchen (4): ARM: at91/dt: add a new DT property to support FIFOs on Atmel USARTs tty/serial: at91: fix some macro definitions to fit coding style tty/serial: at91: add support to FIFOs tty/serial: at91: use 32bit writes into TX FIFO when DMA is enabled .../devicetree/bindings/serial/atmel-usart.txt | 3 + drivers/tty/serial/atmel_serial.c | 193 +++++++++++++---- include/linux/atmel_serial.h | 240 ++++++++++++--------- 3 files changed, 293 insertions(+), 143 deletions(-) -- 1.8.2.2 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/