Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S934621AbbGHJme (ORCPT ); Wed, 8 Jul 2015 05:42:34 -0400 Received: from mailgw01.mediatek.com ([210.61.82.183]:37741 "EHLO mailgw01.mediatek.com" rhost-flags-OK-FAIL-OK-FAIL) by vger.kernel.org with ESMTP id S933686AbbGHJlc (ORCPT ); Wed, 8 Jul 2015 05:41:32 -0400 X-Listener-Flag: 11101 From: Chunfeng Yun To: Mathias Nyman CC: Rob Herring , Mark Rutland , Matthias Brugger , Felipe Balbi , Chunfeng Yun , Sascha Hauer , , , , Roger Quadros , , Subject: [PATCH v2 3/5] usb: phy: add usb3.0 phy driver for mt65xx SoCs Date: Wed, 8 Jul 2015 17:41:05 +0800 Message-ID: <1436348468-4126-4-git-send-email-chunfeng.yun@mediatek.com> X-Mailer: git-send-email 1.8.1.1.dirty In-Reply-To: <1436348468-4126-1-git-send-email-chunfeng.yun@mediatek.com> References: <1436348468-4126-1-git-send-email-chunfeng.yun@mediatek.com> MIME-Version: 1.0 Content-Type: text/plain X-MTK: N Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 27474 Lines: 911 Signed-off-by: Chunfeng Yun --- drivers/usb/phy/Kconfig | 10 + drivers/usb/phy/Makefile | 1 + drivers/usb/phy/phy-mt65xx-usb3.c | 856 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 867 insertions(+) create mode 100644 drivers/usb/phy/phy-mt65xx-usb3.c diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig index 869c0cfcad..66ded00 100644 --- a/drivers/usb/phy/Kconfig +++ b/drivers/usb/phy/Kconfig @@ -152,6 +152,16 @@ config USB_MSM_OTG This driver is not supported on boards like trout which has an external PHY. +config USB_MT65XX_USB3_PHY + tristate "Mediatek USB3.0 PHY controller Driver" + depends on ARCH_MEDIATEK || COMPILE_TEST + select USB_PHY + help + Say 'Y' here to add support for Mediatek USB3.0 PHY driver + for mt65xx SoCs. it supports two usb2.0 ports and + one usb3.0 port. + To compile this driver as a module, choose M here + config USB_MV_OTG tristate "Marvell USB OTG support" depends on USB_EHCI_MV && USB_MV_UDC && PM diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile index e36ab1d..414ef57 100644 --- a/drivers/usb/phy/Makefile +++ b/drivers/usb/phy/Makefile @@ -20,6 +20,7 @@ obj-$(CONFIG_USB_EHCI_TEGRA) += phy-tegra-usb.o obj-$(CONFIG_USB_GPIO_VBUS) += phy-gpio-vbus-usb.o obj-$(CONFIG_USB_ISP1301) += phy-isp1301.o obj-$(CONFIG_USB_MSM_OTG) += phy-msm-usb.o +obj-$(CONFIG_USB_MT65XX_USB3_PHY) += phy-mt65xx-usb3.o obj-$(CONFIG_USB_MV_OTG) += phy-mv-usb.o obj-$(CONFIG_USB_MXS_PHY) += phy-mxs-usb.o obj-$(CONFIG_USB_RCAR_PHY) += phy-rcar-usb.o diff --git a/drivers/usb/phy/phy-mt65xx-usb3.c b/drivers/usb/phy/phy-mt65xx-usb3.c new file mode 100644 index 0000000..38ee6f3 --- /dev/null +++ b/drivers/usb/phy/phy-mt65xx-usb3.c @@ -0,0 +1,856 @@ +/* + * Copyright (c) 2015 MediaTek Inc. + * Author: Chunfeng.Yun + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* + * relative to MAC base address + */ +#define SSUSB_USB3_MAC_CSR_BASE (0x1400) +#define SSUSB_USB3_SYS_CSR_BASE (0x1400) +#define SSUSB_USB2_CSR_BASE (0x2400) + +/* + * for sifslv1 register + * relative to USB3_SIF_BASE base address + */ +#define SSUSB_SIFSLV_IPPC_BASE (0x700) + +/* + * for sifslv2 register + * relative to USB3_SIF_BASE base address + */ +#define SSUSB_SIFSLV_U2PHY_COM_BASE (0x10800) +#define SSUSB_SIFSLV_U3PHYD_BASE (0x10900) +#define SSUSB_SIFSLV_U2FREQ_BASE (0x10f00) +#define SSUSB_USB30_PHYA_SIV_B_BASE (0x10b00) +#define SSUSB_SIFSLV_U3PHYA_DA_BASE (0x10c00) +#define SSUSB_SIFSLV_SPLLC (0x10000) + +/*port1 refs. +0x800(refer to port0)*/ +#define U3P_PORT_OFFSET (0x800) /*based on port0 */ +#define U3P_PHY_BASE(index) ((U3P_PORT_OFFSET) * (index)) + +#define U3P_IP_PW_CTRL0 (SSUSB_SIFSLV_IPPC_BASE + 0x0000) +#define CTRL0_IP_SW_RST (0x1 << 0) + +#define U3P_IP_PW_CTRL1 (SSUSB_SIFSLV_IPPC_BASE + 0x0004) +#define CTRL1_IP_HOST_PDN (0x1 << 0) + +#define U3P_IP_PW_CTRL2 (SSUSB_SIFSLV_IPPC_BASE + 0x0008) +#define CTRL2_IP_DEV_PDN (0x1 << 0) + +#define U3P_IP_PW_STS1 (SSUSB_SIFSLV_IPPC_BASE + 0x0010) +#define STS1_IP_SLEEP_STS (0x1 << 30) +#define STS1_U3_MAC_RST (0x1 << 16) +#define STS1_SYS125_RST (0x1 << 10) +#define STS1_REF_RST (0x1 << 8) +#define STS1_SYSPLL_STABLE (0x1 << 0) + +#define U3P_IP_PW_STS2 (SSUSB_SIFSLV_IPPC_BASE + 0x0014) +#define STS2_U2_MAC_RST (0x1 << 0) + +#define U3P_IP_XHCI_CAP (SSUSB_SIFSLV_IPPC_BASE + 0x0024) +#define CAP_U3_PORT_NUM(p) ((p) & 0xff) +#define CAP_U2_PORT_NUM(p) (((p) >> 8) & 0xff) + +#define U3P_U3_CTRL_0P (SSUSB_SIFSLV_IPPC_BASE + 0x0030) +#define CTRL_U3_PORT_HOST_SEL (0x1 << 2) +#define CTRL_U3_PORT_PDN (0x1 << 1) +#define CTRL_U3_PORT_DIS (0x1 << 0) + +#define U3P_U2_CTRL_0P (SSUSB_SIFSLV_IPPC_BASE + 0x0050) +#define CTRL_U2_PORT_HOST_SEL (0x1 << 2) +#define CTRL_U2_PORT_PDN (0x1 << 1) +#define CTRL_U2_PORT_DIS (0x1 << 0) + +#define U3P_U3_CTRL(p) (U3P_U3_CTRL_0P + ((p) * 0x08)) +#define U3P_U2_CTRL(p) (U3P_U2_CTRL_0P + ((p) * 0x08)) + +#define U3P_USBPHYACR0 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000) +#define PA0_RG_U2PLL_FORCE_ON (0x1 << 15) + +#define U3P_USBPHYACR2 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008) +#define PA2_RG_SIF_U2PLL_FORCE_EN (0x1 << 18) + +#define U3P_USBPHYACR5 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014) +#define PA5_RG_U2_HSTX_SRCTRL (0x7 << 12) +#define PA5_RG_U2_HSTX_SRCTRL_VAL(x) ((0x7 & (x)) << 12) +#define PA5_RG_U2_HS_100U_U3_EN (0x1 << 11) + +#define U3P_USBPHYACR6 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018) +#define PA6_RG_U2_ISO_EN (0x1 << 31) +#define PA6_RG_U2_BC11_SW_EN (0x1 << 23) +#define PA6_RG_U2_OTG_VBUSCMP_EN (0x1 << 20) + +#define U3P_U2PHYACR4 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020) +#define P2C_RG_USB20_GPIO_CTL (0x1 << 9) +#define P2C_USB20_GPIO_MODE (0x1 << 8) +#define P2C_U2_GPIO_CTR_MSK (P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE) + +#define U3D_U2PHYDCR0 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060) +#define P2C_RG_SIF_U2PLL_FORCE_ON (0x1 << 24) + +#define U3P_U2PHYDTM0 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068) +#define P2C_FORCE_UART_EN (0x1 << 26) +#define P2C_FORCE_DATAIN (0x1 << 23) +#define P2C_FORCE_DM_PULLDOWN (0x1 << 21) +#define P2C_FORCE_DP_PULLDOWN (0x1 << 20) +#define P2C_FORCE_XCVRSEL (0x1 << 19) +#define P2C_FORCE_SUSPENDM (0x1 << 18) +#define P2C_FORCE_TERMSEL (0x1 << 17) +#define P2C_RG_DATAIN (0xf << 10) +#define P2C_RG_DATAIN_VAL(x) ((0xf & (x)) << 10) +#define P2C_RG_DMPULLDOWN (0x1 << 7) +#define P2C_RG_DPPULLDOWN (0x1 << 6) +#define P2C_RG_XCVRSEL (0x3 << 4) +#define P2C_RG_XCVRSEL_VAL(x) ((0x3 & (x)) << 4) +#define P2C_RG_SUSPENDM (0x1 << 3) +#define P2C_RG_TERMSEL (0x1 << 2) +#define P2C_DTM0_PART_MASK \ + (P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \ + P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \ + P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \ + P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL) + +#define U3P_U2PHYDTM1 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C) +#define P2C_RG_UART_EN (0x1 << 16) +#define P2C_RG_VBUSVALID (0x1 << 5) +#define P2C_RG_SESSEND (0x1 << 4) +#define P2C_RG_AVALID (0x1 << 2) + +#define U3P_U3_PHYA_REG0 (SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000) +#define P3A_RG_U3_VUSB10_ON (1 << 5) + +#define U3P_U3_PHYA_REG6 (SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018) +#define P3A_RG_TX_EIDLE_CM (0xf << 28) +#define P3A_RG_TX_EIDLE_CM_VAL(x) ((0xf & (x)) << 28) + +#define U3P_U3_PHYA_REG9 (SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024) +#define P3A_RG_RX_DAC_MUX (0x1f << 1) +#define P3A_RG_RX_DAC_MUX_VAL(x) ((0x1f & (x)) << 1) + +#define U3P_U3PHYA_DA_REG0 (SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0) +#define P3A_RG_XTAL_EXT_EN_U3 (0x3 << 10) +#define P3A_RG_XTAL_EXT_EN_U3_VAL(x) ((0x3 & (x)) << 10) + +#define U3P_PHYD_CDR1 (SSUSB_SIFSLV_U3PHYD_BASE + 0x5c) +#define P3D_RG_CDR_BIR_LTD1 (0x1f << 24) +#define P3D_RG_CDR_BIR_LTD1_VAL(x) ((0x1f & (x)) << 24) +#define P3D_RG_CDR_BIR_LTD0 (0x1f << 8) +#define P3D_RG_CDR_BIR_LTD0_VAL(x) ((0x1f & (x)) << 8) + +#define U3P_XTALCTL3 (SSUSB_SIFSLV_SPLLC + 0x18) +#define XC3_RG_U3_XTAL_RX_PWD (0x1 << 9) +#define XC3_RG_U3_FRC_XTAL_RX_PWD (0x1 << 8) + +#define U3P_UX_EXIT_LFPS_PARAM (SSUSB_USB3_MAC_CSR_BASE + 0x00A0) +#define RX_UX_EXIT_REF (0xff << 8) +#define RX_UX_EXIT_REF_VAL (0x3 << 8) + +#define U3P_REF_CLK_PARAM (SSUSB_USB3_MAC_CSR_BASE + 0x00B0) +#define REF_CLK_1000NS (0xff << 0) +#define REF_CLK_VAL_DEF (0xa << 0) + +#define U3P_LINK_PM_TIMER (SSUSB_USB3_SYS_CSR_BASE + 0x0208) +#define PM_LC_TIMEOUT (0xf << 0) +#define PM_LC_TIMEOUT_VAL (0x3 << 0) + +#define U3P_TIMING_PULSE_CTRL (SSUSB_USB3_SYS_CSR_BASE + 0x02B4) +#define U3T_CNT_1US (0xff << 0) +#define U3T_CNT_1US_VAL (0x3f << 0) /* 62.5MHz: 63 */ + +#define U3P_U2_TIMING_PARAM (SSUSB_USB2_CSR_BASE + 0x0040) +#define U2T_VAL_1US (0xff << 0) +#define U2T_VAL_1US_VAL (0x3f << 0) /* 62.5MHz: 63 */ + + +#define PERI_WK_CTRL0 0x400 +#define UWK_CTL1_1P_LS_E (0x1 << 0) +#define UWK_CTL1_1P_LS_C(x) (((x) & 0xf) << 1) +#define UWK_CTR0_0P_LS_NE (0x1 << 7) /* negedge for 0p linestate*/ +#define UWK_CTR0_0P_LS_PE (0x1 << 8) /* posedge */ + +#define PERI_WK_CTRL1 0x404 +#define UWK_CTL1_IS_P (0x1 << 6) /* polarity for ip sleep */ +#define UWK_CTL1_0P_LS_P (0x1 << 7) +#define UWK_CTL1_IDDIG_P (0x1 << 9) /* polarity */ +#define UWK_CTL1_IDDIG_E (0x1 << 10) /* enable debounce */ +#define UWK_CTL1_IDDIG_C(x) (((x) & 0xf) << 11) /* cycle debounce */ +#define UWK_CTL1_0P_LS_E (0x1 << 20) +#define UWK_CTL1_0P_LS_C(x) (((x) & 0xf) << 21) +#define UWK_CTL1_IS_E (0x1 << 25) +#define UWK_CTL1_IS_C(x) (((x) & 0xf) << 26) + +enum ssusb_wakeup_src { + SSUSB_WK_IP_SLEEP = 1, + SSUSB_WK_LINE_STATE = 2, +}; + +struct mt65xx_u3phy { + struct usb_phy phy; + struct device *dev; + void __iomem *mac_base; /* only device-mac regs, exclude xhci's */ + void __iomem *sif_base; /* include sif & sif2 */ + struct regmap *pericfg; + struct clk *wk_deb_p0; /* port0's wakeup debounce clock */ + struct clk *wk_deb_p1; + struct clk *u3phya_ref; /* reference clock of usb3 anolog phy */ + int wakeup_src; + int u2port_num; +}; + + +static void u3p_writel(void __iomem *base, u32 offset, u32 data) +{ + writel(data, base + offset); +} + +static u32 u3p_readl(void __iomem *base, u32 offset) +{ + return readl(base + offset); +} + +static void u3p_setmsk(void __iomem *base, u32 offset, u32 msk) +{ + void __iomem *addr = base + offset; + + writel((readl(addr) | msk), addr); +} + +static void u3p_clrmsk(void __iomem *base, u32 offset, u32 msk) +{ + void __iomem *addr = base + offset; + + writel((readl(addr) & ~msk), addr); +} + +static void u3p_setval(void __iomem *base, u32 offset, + u32 mask, u32 value) +{ + void __iomem *addr = base + offset; + unsigned int new_value; + + new_value = (readl(addr) & ~mask) | value; + writel(new_value, addr); +} + +static void phy_index_power_on(struct mt65xx_u3phy *u3phy, int index) +{ + void __iomem *sif_base = u3phy->sif_base + U3P_PHY_BASE(index); + + if (!index) { + /* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */ + u3p_setmsk(sif_base, U3P_U3_PHYA_REG0, P3A_RG_U3_VUSB10_ON); + /* power domain iso disable */ + u3p_clrmsk(sif_base, U3P_USBPHYACR6, PA6_RG_U2_ISO_EN); + } + + /* switch to USB function. (system register, force ip into usb mode) */ + u3p_clrmsk(sif_base, U3P_U2PHYDTM0, P2C_FORCE_UART_EN); + u3p_clrmsk(sif_base, U3P_U2PHYDTM1, P2C_RG_UART_EN); + if (!index) + u3p_clrmsk(sif_base, U3P_U2PHYACR4, P2C_U2_GPIO_CTR_MSK); + + /* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */ + u3p_clrmsk(sif_base, U3P_U2PHYDTM0, P2C_FORCE_SUSPENDM); + u3p_clrmsk(sif_base, U3P_U2PHYDTM0, + P2C_RG_XCVRSEL | P2C_RG_DATAIN | P2C_DTM0_PART_MASK); + + /* DP/DM BC1.1 path Disable */ + u3p_clrmsk(sif_base, U3P_USBPHYACR6, PA6_RG_U2_BC11_SW_EN); + /* OTG Enable */ + u3p_setmsk(sif_base, U3P_USBPHYACR6, PA6_RG_U2_OTG_VBUSCMP_EN); + u3p_setval(sif_base, U3P_U3PHYA_DA_REG0, P3A_RG_XTAL_EXT_EN_U3, + P3A_RG_XTAL_EXT_EN_U3_VAL(2)); + u3p_setval(sif_base, U3P_U3_PHYA_REG9, P3A_RG_RX_DAC_MUX, + P3A_RG_RX_DAC_MUX_VAL(4)); + + if (!index) { + u3p_setmsk(sif_base, U3P_XTALCTL3, XC3_RG_U3_XTAL_RX_PWD); + u3p_setmsk(sif_base, U3P_XTALCTL3, XC3_RG_U3_FRC_XTAL_RX_PWD); + /* [mt8173]disable Change 100uA current from SSUSB */ + u3p_clrmsk(sif_base, U3P_USBPHYACR5, PA5_RG_U2_HS_100U_U3_EN); + } + u3p_setval(sif_base, U3P_U3_PHYA_REG6, P3A_RG_TX_EIDLE_CM, + P3A_RG_TX_EIDLE_CM_VAL(0xe)); + u3p_setval(sif_base, U3P_PHYD_CDR1, P3D_RG_CDR_BIR_LTD0, + P3D_RG_CDR_BIR_LTD0_VAL(0xc)); + u3p_setval(sif_base, U3P_PHYD_CDR1, P3D_RG_CDR_BIR_LTD1, + P3D_RG_CDR_BIR_LTD1_VAL(0x3)); + + udelay(800); + u3p_setmsk(sif_base, U3P_U2PHYDTM1, P2C_RG_VBUSVALID | P2C_RG_AVALID); + u3p_clrmsk(sif_base, U3P_U2PHYDTM1, P2C_RG_SESSEND); + + /* USB 2.0 slew rate calibration */ + u3p_setval(sif_base, U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCTRL, + PA5_RG_U2_HSTX_SRCTRL_VAL(4)); + + dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index); +} + +static void phy_index_power_off(struct mt65xx_u3phy *u3phy, int index) +{ + void __iomem *sif_base = u3phy->sif_base + U3P_PHY_BASE(index); + + /* switch to USB function. (system register, force ip into usb mode) */ + u3p_clrmsk(sif_base, U3P_U2PHYDTM0, P2C_FORCE_UART_EN); + u3p_clrmsk(sif_base, U3P_U2PHYDTM1, P2C_RG_UART_EN); + if (!index) + u3p_clrmsk(sif_base, U3P_U2PHYACR4, P2C_U2_GPIO_CTR_MSK); + + u3p_setmsk(sif_base, U3P_U2PHYDTM0, P2C_FORCE_SUSPENDM); + u3p_setval(sif_base, U3P_U2PHYDTM0, + P2C_RG_XCVRSEL, P2C_RG_XCVRSEL_VAL(1)); + u3p_setval(sif_base, U3P_U2PHYDTM0, + P2C_RG_DATAIN, P2C_RG_DATAIN_VAL(0)); + u3p_setmsk(sif_base, U3P_U2PHYDTM0, P2C_DTM0_PART_MASK); + /* DP/DM BC1.1 path Disable */ + u3p_clrmsk(sif_base, U3P_USBPHYACR6, PA6_RG_U2_BC11_SW_EN); + /* OTG Disable */ + u3p_clrmsk(sif_base, U3P_USBPHYACR6, PA6_RG_U2_OTG_VBUSCMP_EN); + if (!index) { + /* Change 100uA current switch to USB2.0 */ + u3p_clrmsk(sif_base, U3P_USBPHYACR5, PA5_RG_U2_HS_100U_U3_EN); + } + udelay(800); + + /* let suspendm=0, set utmi into analog power down */ + u3p_clrmsk(sif_base, U3P_U2PHYDTM0, P2C_RG_SUSPENDM); + udelay(1); + + u3p_clrmsk(sif_base, U3P_U2PHYDTM1, P2C_RG_VBUSVALID | P2C_RG_AVALID); + u3p_setmsk(sif_base, U3P_U2PHYDTM1, P2C_RG_SESSEND); + if (!index) { + /* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */ + u3p_clrmsk(sif_base, U3P_U3_PHYA_REG0, P3A_RG_U3_VUSB10_ON); + } + dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index); +} + +static void u3phy_power_on(struct mt65xx_u3phy *u3phy) +{ + phy_index_power_on(u3phy, 0); + if (u3phy->u2port_num > 1) + phy_index_power_on(u3phy, 1); +} + +static void u3phy_power_off(struct mt65xx_u3phy *u3phy) +{ + phy_index_power_off(u3phy, 0); + if (u3phy->u2port_num > 1) + phy_index_power_off(u3phy, 1); +} + +static int check_ip_clk_status(struct mt65xx_u3phy *u3phy) +{ + int ret; + int u3_port_num; + int u2_port_num; + u32 xhci_cap; + u32 val; + void __iomem *sif_base = u3phy->sif_base; + + xhci_cap = u3p_readl(sif_base, U3P_IP_XHCI_CAP); + u3_port_num = CAP_U3_PORT_NUM(xhci_cap); + u2_port_num = CAP_U2_PORT_NUM(xhci_cap); + + ret = readl_poll_timeout(sif_base + U3P_IP_PW_STS1, val, + (val & STS1_SYSPLL_STABLE), 100, 10000); + if (ret) { + dev_err(u3phy->dev, "sypll is not stable!!!\n"); + return ret; + } + + ret = readl_poll_timeout(sif_base + U3P_IP_PW_STS1, val, + (val & STS1_REF_RST), 100, 10000); + if (ret) { + dev_err(u3phy->dev, "ref_clk is still active!!!\n"); + return ret; + } + + ret = readl_poll_timeout(sif_base + U3P_IP_PW_STS1, val, + (val & STS1_SYS125_RST), 100, 10000); + if (ret) { + dev_err(u3phy->dev, "sys125_ck is still active!!!\n"); + return ret; + } + + if (u3_port_num) { + ret = readl_poll_timeout(sif_base + U3P_IP_PW_STS1, val, + (val & STS1_U3_MAC_RST), 100, 10000); + if (ret) { + dev_err(u3phy->dev, "mac3_mac_ck is still active!!!\n"); + return ret; + } + } + + if (u2_port_num) { + ret = readl_poll_timeout(sif_base + U3P_IP_PW_STS2, val, + (val & STS2_U2_MAC_RST), 100, 10000); + if (ret) { + dev_err(u3phy->dev, "mac2_sys_ck is still active!!!\n"); + return ret; + } + } + + return 0; +} + +static int u3phy_ports_enable(struct mt65xx_u3phy *u3phy) +{ + int i; + u32 temp; + int u3_port_num; + int u2_port_num; + void __iomem *sif_base = u3phy->sif_base; + + temp = u3p_readl(sif_base, U3P_IP_XHCI_CAP); + u3_port_num = CAP_U3_PORT_NUM(temp); + u2_port_num = CAP_U2_PORT_NUM(temp); + dev_dbg(u3phy->dev, "%s u2p:%d, u3p:%d\n", + __func__, u2_port_num, u3_port_num); + + /* power on host ip */ + u3p_clrmsk(sif_base, U3P_IP_PW_CTRL1, CTRL1_IP_HOST_PDN); + + /* power on and enable all u3 ports */ + for (i = 0; i < u3_port_num; i++) { + temp = u3p_readl(sif_base, U3P_U3_CTRL(i)); + temp &= ~(CTRL_U3_PORT_PDN | CTRL_U3_PORT_DIS); + temp |= CTRL_U3_PORT_HOST_SEL; + u3p_writel(sif_base, U3P_U3_CTRL(i), temp); + } + + /* power on and enable all u2 ports */ + for (i = 0; i < u2_port_num; i++) { + temp = u3p_readl(sif_base, U3P_U2_CTRL(i)); + temp &= ~(CTRL_U2_PORT_PDN | CTRL_U2_PORT_DIS); + temp |= CTRL_U2_PORT_HOST_SEL; + u3p_writel(sif_base, U3P_U2_CTRL(i), temp); + } + return check_ip_clk_status(u3phy); +} + +static int u3phy_ports_disable(struct mt65xx_u3phy *u3phy) +{ + int i; + u32 temp; + int ret; + int u3_port_num; + int u2_port_num; + void __iomem *sif_base = u3phy->sif_base; + + temp = u3p_readl(sif_base, U3P_IP_XHCI_CAP); + u3_port_num = CAP_U3_PORT_NUM(temp); + u2_port_num = CAP_U2_PORT_NUM(temp); + dev_dbg(u3phy->dev, "%s u2p:%d, u3p:%d\n", + __func__, u2_port_num, u3_port_num); + + /* power on and enable all u3 ports */ + for (i = 0; i < u3_port_num; i++) { + temp = u3p_readl(sif_base, U3P_U3_CTRL(i)); + temp |= CTRL_U3_PORT_PDN; + u3p_writel(sif_base, U3P_U3_CTRL(i), temp); + } + + /* power on and enable all u2 ports */ + for (i = 0; i < u2_port_num; i++) { + temp = u3p_readl(sif_base, U3P_U2_CTRL(i)); + temp |= CTRL_U2_PORT_PDN; + u3p_writel(sif_base, U3P_U2_CTRL(i), temp); + } + + /* power off host ip */ + u3p_setmsk(sif_base, U3P_IP_PW_CTRL1, CTRL1_IP_HOST_PDN); + u3p_setmsk(sif_base, U3P_IP_PW_CTRL2, CTRL2_IP_DEV_PDN); + + ret = readl_poll_timeout(sif_base + U3P_IP_PW_STS1, temp, + (temp & STS1_IP_SLEEP_STS), 100, 100000); + if (ret) { + dev_err(u3phy->dev, "ip sleep failed!!!\n"); + return ret; + } + return 0; +} + +static void u3phy_timing_init(struct mt65xx_u3phy *u3phy) +{ + void __iomem *mbase = u3phy->mac_base; + int u3_port_num; + u32 temp; + + temp = u3p_readl(u3phy->sif_base, U3P_IP_XHCI_CAP); + u3_port_num = CAP_U3_PORT_NUM(temp); + + if (u3_port_num) { + /* set MAC reference clock speed */ + u3p_setval(mbase, U3P_UX_EXIT_LFPS_PARAM, + RX_UX_EXIT_REF, RX_UX_EXIT_REF_VAL); + /* set REF_CLK */ + u3p_setval(mbase, U3P_REF_CLK_PARAM, + REF_CLK_1000NS, REF_CLK_VAL_DEF); + /* set SYS_CLK */ + u3p_setval(mbase, U3P_TIMING_PULSE_CTRL, + U3T_CNT_1US, U3T_CNT_1US_VAL); + /* set LINK_PM_TIMER=3 */ + u3p_setval(mbase, U3P_LINK_PM_TIMER, + PM_LC_TIMEOUT, PM_LC_TIMEOUT_VAL); + } + u3p_setval(mbase, U3P_U2_TIMING_PARAM, U2T_VAL_1US, U2T_VAL_1US_VAL); +} + +static int u3phy_clks_enable(struct mt65xx_u3phy *u3phy) +{ + int ret; + + ret = clk_prepare_enable(u3phy->u3phya_ref); + if (ret) { + dev_err(u3phy->dev, "failed to enable u3phya_ref\n"); + goto u3phya_ref_err; + } + ret = clk_prepare_enable(u3phy->wk_deb_p0); + if (ret) { + dev_err(u3phy->dev, "failed to enable wk_deb_p0\n"); + goto usb_p0_err; + } + if (u3phy->u2port_num > 1) { + ret = clk_prepare_enable(u3phy->wk_deb_p1); + if (ret) { + dev_err(u3phy->dev, "failed to enable wk_deb_p1\n"); + goto usb_p1_err; + } + } + udelay(50); + + return 0; + +usb_p1_err: + clk_disable_unprepare(u3phy->wk_deb_p0); +usb_p0_err: + clk_disable_unprepare(u3phy->u3phya_ref); +u3phya_ref_err: + return -EINVAL; +} + +static void u3phy_clks_disable(struct mt65xx_u3phy *u3phy) +{ + if (u3phy->u2port_num > 1) + clk_disable_unprepare(u3phy->wk_deb_p1); + clk_disable_unprepare(u3phy->wk_deb_p0); + clk_disable_unprepare(u3phy->u3phya_ref); +} + +/* only clocks can be turn off for ip-sleep wakeup mode */ +static void usb_wakeup_ip_sleep_en(struct mt65xx_u3phy *u3phy) +{ + u32 tmp; + struct regmap *pericfg = u3phy->pericfg; + + regmap_read(pericfg, PERI_WK_CTRL1, &tmp); + tmp &= ~UWK_CTL1_IS_P; + tmp &= ~(UWK_CTL1_IS_C(0xf)); + tmp |= UWK_CTL1_IS_C(0x8); + regmap_write(pericfg, PERI_WK_CTRL1, tmp); + regmap_write(pericfg, PERI_WK_CTRL1, tmp | UWK_CTL1_IS_E); + + regmap_read(pericfg, PERI_WK_CTRL1, &tmp); + dev_dbg(u3phy->dev, "%s(): WK_CTRL1[P6,E25,C26:29]=%#x\n", __func__, + tmp); +} + +static void usb_wakeup_ip_sleep_dis(struct mt65xx_u3phy *u3phy) +{ + u32 tmp; + + regmap_read(u3phy->pericfg, PERI_WK_CTRL1, &tmp); + tmp &= ~UWK_CTL1_IS_E; + regmap_write(u3phy->pericfg, PERI_WK_CTRL1, tmp); +} + +/* +* for line-state wakeup mode, phy's power should not power-down +* and only support cable plug in/out +*/ +static void usb_wakeup_line_state_en(struct mt65xx_u3phy *u3phy) +{ + u32 tmp; + struct regmap *pericfg = u3phy->pericfg; + + /* line-state of u2-port0 */ + regmap_read(pericfg, PERI_WK_CTRL1, &tmp); + tmp &= ~UWK_CTL1_0P_LS_P; + tmp &= ~(UWK_CTL1_0P_LS_C(0xf)); + tmp |= UWK_CTL1_0P_LS_C(0x8); + regmap_write(pericfg, PERI_WK_CTRL1, tmp); + regmap_read(pericfg, PERI_WK_CTRL1, &tmp); + regmap_write(pericfg, PERI_WK_CTRL1, tmp | UWK_CTL1_0P_LS_E); + + /* line-state of u2-port1 if support */ + if (u3phy->u2port_num > 1) { + regmap_read(pericfg, PERI_WK_CTRL0, &tmp); + tmp &= ~(UWK_CTL1_1P_LS_C(0xf)); + tmp |= UWK_CTL1_1P_LS_C(0x8); + regmap_write(pericfg, PERI_WK_CTRL0, tmp); + regmap_write(pericfg, PERI_WK_CTRL0, tmp | UWK_CTL1_1P_LS_E); + } +} + +static void usb_wakeup_line_state_dis(struct mt65xx_u3phy *u3phy) +{ + u32 tmp; + struct regmap *pericfg = u3phy->pericfg; + + regmap_read(pericfg, PERI_WK_CTRL1, &tmp); + tmp &= ~UWK_CTL1_0P_LS_E; + regmap_write(pericfg, PERI_WK_CTRL1, tmp); + + if (u3phy->u2port_num > 1) { + regmap_read(pericfg, PERI_WK_CTRL0, &tmp); + tmp &= ~UWK_CTL1_1P_LS_E; + regmap_write(pericfg, PERI_WK_CTRL0, tmp); + } +} + +static void usb_wakeup_enable(struct mt65xx_u3phy *u3phy) +{ + if (u3phy->wakeup_src == SSUSB_WK_IP_SLEEP) + usb_wakeup_ip_sleep_en(u3phy); + else if (u3phy->wakeup_src == SSUSB_WK_LINE_STATE) + usb_wakeup_line_state_en(u3phy); +} + +static void usb_wakeup_disable(struct mt65xx_u3phy *u3phy) +{ + if (u3phy->wakeup_src == SSUSB_WK_IP_SLEEP) + usb_wakeup_ip_sleep_dis(u3phy); + else if (u3phy->wakeup_src == SSUSB_WK_LINE_STATE) + usb_wakeup_line_state_dis(u3phy); +} + +static int mt65xx_u3phy_init(struct usb_phy *phy) +{ + struct mt65xx_u3phy *u3phy; + int ret; + + u3phy = container_of(phy, struct mt65xx_u3phy, phy); + dev_dbg(u3phy->dev, "%s+\n", __func__); + + ret = pm_runtime_get_sync(u3phy->dev); + if (ret < 0) + goto pm_err; + + ret = u3phy_clks_enable(u3phy); + if (ret) { + dev_err(u3phy->dev, "failed to enable clks\n"); + goto clks_err; + } + + /* reset whole ip */ + u3p_setmsk(u3phy->sif_base, U3P_IP_PW_CTRL0, CTRL0_IP_SW_RST); + u3p_clrmsk(u3phy->sif_base, U3P_IP_PW_CTRL0, CTRL0_IP_SW_RST); + + ret = u3phy_ports_enable(u3phy); + if (ret) { + dev_err(u3phy->dev, "failed to enable ports\n"); + goto port_err; + } + u3phy_timing_init(u3phy); + u3phy_power_on(u3phy); + msleep(40); + + return 0; + +port_err: + u3phy_clks_disable(u3phy); +clks_err: + pm_runtime_put_sync(u3phy->dev); +pm_err: + return ret; +} + + +static void mt65xx_u3phy_shutdown(struct usb_phy *phy) +{ + struct mt65xx_u3phy *u3phy; + + u3phy = container_of(phy, struct mt65xx_u3phy, phy); + u3phy_power_off(u3phy); + u3phy_clks_disable(u3phy); + pm_runtime_put_sync(u3phy->dev); +} + + +static int mt65xx_u3phy_suspend(struct usb_phy *x, int suspend) +{ + struct mt65xx_u3phy *u3phy = container_of(x, struct mt65xx_u3phy, phy); + + if (suspend) { + u3phy_ports_disable(u3phy); + u3phy_power_off(u3phy); + u3phy_clks_disable(u3phy); + usb_wakeup_enable(u3phy); + } else { + usb_wakeup_disable(u3phy); + u3phy_clks_enable(u3phy); + u3phy_power_on(u3phy); + u3phy_ports_enable(u3phy); + } + return 0; +} + + +static const struct of_device_id mt65xx_u3phy_id_table[] = { + { .compatible = "mediatek,mt8173-u3phy",}, + { }, +}; +MODULE_DEVICE_TABLE(of, mt65xx_u3phy_id_table); + + +static int mt65xx_u3phy_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + struct resource *mac_res; + struct resource *sif_res; + struct mt65xx_u3phy *u3phy; + int retval = -ENOMEM; + + u3phy = devm_kzalloc(&pdev->dev, sizeof(*u3phy), GFP_KERNEL); + if (!u3phy) + goto err; + + u3phy->dev = &pdev->dev; + + mac_res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + u3phy->mac_base = devm_ioremap_resource(dev, mac_res); + if (IS_ERR(u3phy->mac_base)) { + dev_err(dev, "failed to remap mac regs\n"); + retval = PTR_ERR(u3phy->mac_base); + goto err; + } + + sif_res = platform_get_resource(pdev, IORESOURCE_MEM, 1); + u3phy->sif_base = devm_ioremap_resource(dev, sif_res); + if (IS_ERR(u3phy->sif_base)) { + dev_err(dev, "failed to remap sif regs\n"); + retval = PTR_ERR(u3phy->sif_base); + goto err; + } + + of_property_read_u32(np, "u2port-num", &u3phy->u2port_num); + of_property_read_u32(np, "wakeup-src", &u3phy->wakeup_src); + + u3phy->u3phya_ref = devm_clk_get(dev, "u3phya_ref"); + if (IS_ERR(u3phy->u3phya_ref)) { + dev_err(dev, "error to get u3phya_ref\n"); + retval = PTR_ERR(u3phy->u3phya_ref); + goto err; + } + + u3phy->wk_deb_p0 = devm_clk_get(u3phy->dev, "wakeup_deb_p0"); + if (IS_ERR(u3phy->wk_deb_p0)) { + dev_err(dev, "error to get wakeup_deb_p0\n"); + retval = PTR_ERR(u3phy->wk_deb_p0); + goto err; + } + + if (u3phy->u2port_num > 1) { + u3phy->wk_deb_p1 = devm_clk_get(u3phy->dev, "wakeup_deb_p1"); + if (IS_ERR(u3phy->wk_deb_p1)) { + dev_err(dev, "error to get wakeup_deb_p1\n"); + retval = PTR_ERR(u3phy->wk_deb_p1); + goto err; + } + } + + u3phy->pericfg = syscon_regmap_lookup_by_phandle(np, "usb-wakeup-ctrl"); + if (IS_ERR(u3phy->pericfg)) { + dev_err(dev, "cannot get pericfg regs\n"); + retval = PTR_ERR(u3phy->pericfg); + goto err; + } + + device_init_wakeup(dev, 1); + pm_runtime_enable(dev); + u3phy->phy.dev = u3phy->dev; + u3phy->phy.label = "mt65xx-usb3phy"; + u3phy->phy.type = USB_PHY_TYPE_USB3; + u3phy->phy.init = mt65xx_u3phy_init; + u3phy->phy.shutdown = mt65xx_u3phy_shutdown; + u3phy->phy.set_suspend = mt65xx_u3phy_suspend; + + platform_set_drvdata(pdev, u3phy); + retval = usb_add_phy_dev(&u3phy->phy); + if (retval) { + dev_err(dev, "failed to add phy\n"); + goto add_phy_err; + } + + return 0; + +add_phy_err: + pm_runtime_disable(dev); +err: + return retval; +} + +static int mt65xx_u3phy_remove(struct platform_device *pdev) +{ + struct mt65xx_u3phy *u3phy = platform_get_drvdata(pdev); + + mt65xx_u3phy_shutdown(&u3phy->phy); + device_init_wakeup(&pdev->dev, 0); + pm_runtime_disable(&pdev->dev); + usb_remove_phy(&u3phy->phy); + + return 0; +} + +static struct platform_driver mt65xx_u3phy_driver = { + .probe = mt65xx_u3phy_probe, + .remove = mt65xx_u3phy_remove, + .driver = { + .name = "mt65xx-u3phy", + .of_match_table = mt65xx_u3phy_id_table, + }, +}; + +module_platform_driver(mt65xx_u3phy_driver); + +MODULE_DESCRIPTION("Mt65xx USB PHY driver"); +MODULE_LICENSE("GPL v2"); -- 1.8.1.1.dirty -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/