Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1753196AbbGNHjV (ORCPT ); Tue, 14 Jul 2015 03:39:21 -0400 Received: from mail-pa0-f49.google.com ([209.85.220.49]:33988 "EHLO mail-pa0-f49.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1753115AbbGNHjQ (ORCPT ); Tue, 14 Jul 2015 03:39:16 -0400 From: Vaibhav Hiremath To: linux-i2c@vger.kernel.org Cc: wsa@the-dreams.de, robh+dt@kernel.org, robert.jarzmik@free.fr, yizhang@marvell.com, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, Vaibhav Hiremath , "Jett.Zhou" Subject: [PATCH-v4 02/11] i2c: pxa: No need to set slave addr for i2c master mode reset Date: Tue, 14 Jul 2015 13:06:41 +0530 Message-Id: <1436859410-28878-3-git-send-email-vaibhav.hiremath@linaro.org> X-Mailer: git-send-email 1.9.1 In-Reply-To: <1436859410-28878-1-git-send-email-vaibhav.hiremath@linaro.org> References: <1436859410-28878-1-git-send-email-vaibhav.hiremath@linaro.org> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 1404 Lines: 37 Normally i2c controller works as master, so slave addr is not needed, or it will impact some slave device (eg. ST NFC chip) i2c accesses, because it has the same i2c address with controller. For example, On the pxa1928 based platform, where PMIC (88pm860) is present @0x30 address on TWSI0 interface, and if we set 0x30 as a slave address in pxa1928 TWSI0 module, all the transactions towards PMIC would go for toss. Signed-off-by: Jett.Zhou Signed-off-by: Vaibhav Hiremath Acked-by: Robert Jarzmik --- drivers/i2c/busses/i2c-pxa.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/i2c/busses/i2c-pxa.c b/drivers/i2c/busses/i2c-pxa.c index f4ac8c5..023e59f 100644 --- a/drivers/i2c/busses/i2c-pxa.c +++ b/drivers/i2c/busses/i2c-pxa.c @@ -459,7 +459,7 @@ static void i2c_pxa_reset(struct pxa_i2c *i2c) writel(I2C_ISR_INIT, _ISR(i2c)); writel(readl(_ICR(i2c)) & ~ICR_UR, _ICR(i2c)); - if (i2c->reg_isar) + if (i2c->reg_isar && IS_ENABLED(CONFIG_I2C_PXA_SLAVE)) writel(i2c->slave_addr, _ISAR(i2c)); /* set control register values */ -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/