Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1753549AbbGTMZv (ORCPT ); Mon, 20 Jul 2015 08:25:51 -0400 Received: from eusmtp01.atmel.com ([212.144.249.243]:19585 "EHLO eusmtp01.atmel.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752193AbbGTMZt (ORCPT ); Mon, 20 Jul 2015 08:25:49 -0400 Message-ID: <55ACE886.1060206@atmel.com> Date: Mon, 20 Jul 2015 14:24:38 +0200 From: Nicolas Ferre Organization: atmel User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:31.0) Gecko/20100101 Thunderbird/31.7.0 MIME-Version: 1.0 To: Cyrille Pitchen , , , , , , , CC: , , , , , , , Subject: Re: [PATCH v4 3/5] tty/serial: at91: remove bunch of macros to access UART registers References: <89084496e1f1f189335d945167aa5327ee36a4a0.1435842688.git.cyrille.pitchen@atmel.com> In-Reply-To: <89084496e1f1f189335d945167aa5327ee36a4a0.1435842688.git.cyrille.pitchen@atmel.com> Content-Type: text/plain; charset="windows-1252" Content-Transfer-Encoding: 8bit X-Originating-IP: [10.161.30.18] Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 32513 Lines: 871 Le 02/07/2015 15:18, Cyrille Pitchen a ?crit : > This patch replaces the UART_PUT_*, resp. UART_GET_*, macros by > atmel_uart_writel(), resp. atmel_uart_readl(), inline function calls. > > Signed-off-by: Cyrille Pitchen Ok with this move: Acked-by: Nicolas Ferre > --- > drivers/tty/serial/atmel_serial.c | 313 +++++++++++++++++++------------------- > 1 file changed, 159 insertions(+), 154 deletions(-) > > diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c > index 2a8f528153e7..e7c337de31d1 100644 > --- a/drivers/tty/serial/atmel_serial.c > +++ b/drivers/tty/serial/atmel_serial.c > @@ -88,37 +88,6 @@ static void atmel_stop_rx(struct uart_port *port); > > #define ATMEL_ISR_PASS_LIMIT 256 > > -/* UART registers. CR is write-only, hence no GET macro */ > -#define UART_PUT_CR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_CR) > -#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR) > -#define UART_PUT_MR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_MR) > -#define UART_PUT_IER(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IER) > -#define UART_PUT_IDR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IDR) > -#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR) > -#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR) > -#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR) > -#define UART_PUT_CHAR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_THR) > -#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR) > -#define UART_PUT_BRGR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR) > -#define UART_PUT_RTOR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR) > -#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR) > -#define UART_GET_IP_NAME(port) __raw_readl((port)->membase + ATMEL_US_NAME) > -#define UART_GET_IP_VERSION(port) __raw_readl((port)->membase + ATMEL_US_VERSION) > - > - /* PDC registers */ > -#define UART_PUT_PTCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR) > -#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR) > - > -#define UART_PUT_RPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR) > -#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR) > -#define UART_PUT_RCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR) > -#define UART_PUT_RNPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR) > -#define UART_PUT_RNCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR) > - > -#define UART_PUT_TPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR) > -#define UART_PUT_TCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR) > -#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR) > - > struct atmel_dma_buffer { > unsigned char *buf; > dma_addr_t dma_addr; > @@ -212,6 +181,16 @@ to_atmel_uart_port(struct uart_port *uart) > return container_of(uart, struct atmel_uart_port, uart); > } > > +static inline u32 atmel_uart_readl(struct uart_port *port, u32 reg) > +{ > + return __raw_readl(port->membase + reg); > +} > + > +static inline void atmel_uart_writel(struct uart_port *port, u32 reg, u32 value) > +{ > + __raw_writel(value, port->membase + reg); > +} > + > #ifdef CONFIG_SERIAL_ATMEL_PDC > static bool atmel_use_pdc_rx(struct uart_port *port) > { > @@ -257,7 +236,7 @@ static unsigned int atmel_get_lines_status(struct uart_port *port) > struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); > unsigned int status, ret = 0; > > - status = UART_GET_CSR(port); > + status = atmel_uart_readl(port, ATMEL_US_CSR); > > mctrl_gpio_get(atmel_port->gpios, &ret); > > @@ -304,9 +283,9 @@ static int atmel_config_rs485(struct uart_port *port, > unsigned int mode; > > /* Disable interrupts */ > - UART_PUT_IDR(port, atmel_port->tx_done_mask); > + atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask); > > - mode = UART_GET_MR(port); > + mode = atmel_uart_readl(port, ATMEL_US_MR); > > /* Resetting serial mode to RS232 (0x0) */ > mode &= ~ATMEL_US_USMODE; > @@ -316,7 +295,8 @@ static int atmel_config_rs485(struct uart_port *port, > if (rs485conf->flags & SER_RS485_ENABLED) { > dev_dbg(port->dev, "Setting UART to RS485\n"); > atmel_port->tx_done_mask = ATMEL_US_TXEMPTY; > - UART_PUT_TTGR(port, rs485conf->delay_rts_after_send); > + atmel_uart_writel(port, ATMEL_US_TTGR, > + rs485conf->delay_rts_after_send); > mode |= ATMEL_US_USMODE_RS485; > } else { > dev_dbg(port->dev, "Setting UART to RS232\n"); > @@ -326,10 +306,10 @@ static int atmel_config_rs485(struct uart_port *port, > else > atmel_port->tx_done_mask = ATMEL_US_TXRDY; > } > - UART_PUT_MR(port, mode); > + atmel_uart_writel(port, ATMEL_US_MR, mode); > > /* Enable interrupts */ > - UART_PUT_IER(port, atmel_port->tx_done_mask); > + atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask); > > return 0; > } > @@ -339,7 +319,9 @@ static int atmel_config_rs485(struct uart_port *port, > */ > static u_int atmel_tx_empty(struct uart_port *port) > { > - return (UART_GET_CSR(port) & ATMEL_US_TXEMPTY) ? TIOCSER_TEMT : 0; > + return (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXEMPTY) ? > + TIOCSER_TEMT : > + 0; > } > > /* > @@ -348,13 +330,14 @@ static u_int atmel_tx_empty(struct uart_port *port) > static void atmel_set_mctrl(struct uart_port *port, u_int mctrl) > { > unsigned int control = 0; > - unsigned int mode = UART_GET_MR(port); > + unsigned int mode = atmel_uart_readl(port, ATMEL_US_MR); > unsigned int rts_paused, rts_ready; > struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); > > /* override mode to RS485 if needed, otherwise keep the current mode */ > if (port->rs485.flags & SER_RS485_ENABLED) { > - UART_PUT_TTGR(port, port->rs485.delay_rts_after_send); > + atmel_uart_writel(port, ATMEL_US_TTGR, > + port->rs485.delay_rts_after_send); > mode &= ~ATMEL_US_USMODE; > mode |= ATMEL_US_USMODE_RS485; > } > @@ -384,7 +367,7 @@ static void atmel_set_mctrl(struct uart_port *port, u_int mctrl) > else > control |= ATMEL_US_DTRDIS; > > - UART_PUT_CR(port, control); > + atmel_uart_writel(port, ATMEL_US_CR, control); > > mctrl_gpio_set(atmel_port->gpios, mctrl); > > @@ -395,7 +378,7 @@ static void atmel_set_mctrl(struct uart_port *port, u_int mctrl) > else > mode |= ATMEL_US_CHMODE_NORMAL; > > - UART_PUT_MR(port, mode); > + atmel_uart_writel(port, ATMEL_US_MR, mode); > } > > /* > @@ -406,7 +389,7 @@ static u_int atmel_get_mctrl(struct uart_port *port) > struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); > unsigned int ret = 0, status; > > - status = UART_GET_CSR(port); > + status = atmel_uart_readl(port, ATMEL_US_CSR); > > /* > * The control signals are active low. > @@ -432,10 +415,10 @@ static void atmel_stop_tx(struct uart_port *port) > > if (atmel_use_pdc_tx(port)) { > /* disable PDC transmit */ > - UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS); > + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS); > } > /* Disable interrupts */ > - UART_PUT_IDR(port, atmel_port->tx_done_mask); > + atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask); > > if ((port->rs485.flags & SER_RS485_ENABLED) && > !(port->rs485.flags & SER_RS485_RX_DURING_TX)) > @@ -450,7 +433,7 @@ static void atmel_start_tx(struct uart_port *port) > struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); > > if (atmel_use_pdc_tx(port)) { > - if (UART_GET_PTSR(port) & ATMEL_PDC_TXTEN) > + if (atmel_uart_readl(port, ATMEL_PDC_PTSR) & ATMEL_PDC_TXTEN) > /* The transmitter is already running. Yes, we > really need this.*/ > return; > @@ -460,10 +443,10 @@ static void atmel_start_tx(struct uart_port *port) > atmel_stop_rx(port); > > /* re-enable PDC transmit */ > - UART_PUT_PTCR(port, ATMEL_PDC_TXTEN); > + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); > } > /* Enable interrupts */ > - UART_PUT_IER(port, atmel_port->tx_done_mask); > + atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask); > } > > /* > @@ -471,17 +454,19 @@ static void atmel_start_tx(struct uart_port *port) > */ > static void atmel_start_rx(struct uart_port *port) > { > - UART_PUT_CR(port, ATMEL_US_RSTSTA); /* reset status and receiver */ > + /* reset status and receiver */ > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); > > - UART_PUT_CR(port, ATMEL_US_RXEN); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXEN); > > if (atmel_use_pdc_rx(port)) { > /* enable PDC controller */ > - UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT | > - port->read_status_mask); > - UART_PUT_PTCR(port, ATMEL_PDC_RXTEN); > + atmel_uart_writel(port, ATMEL_US_IER, > + ATMEL_US_ENDRX | ATMEL_US_TIMEOUT | > + port->read_status_mask); > + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN); > } else { > - UART_PUT_IER(port, ATMEL_US_RXRDY); > + atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY); > } > } > > @@ -490,15 +475,16 @@ static void atmel_start_rx(struct uart_port *port) > */ > static void atmel_stop_rx(struct uart_port *port) > { > - UART_PUT_CR(port, ATMEL_US_RXDIS); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXDIS); > > if (atmel_use_pdc_rx(port)) { > /* disable PDC receive */ > - UART_PUT_PTCR(port, ATMEL_PDC_RXTDIS); > - UART_PUT_IDR(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT | > - port->read_status_mask); > + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS); > + atmel_uart_writel(port, ATMEL_US_IDR, > + ATMEL_US_ENDRX | ATMEL_US_TIMEOUT | > + port->read_status_mask); > } else { > - UART_PUT_IDR(port, ATMEL_US_RXRDY); > + atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXRDY); > } > } > > @@ -538,7 +524,7 @@ static void atmel_enable_ms(struct uart_port *port) > else > ier |= ATMEL_US_DCDIC; > > - UART_PUT_IER(port, ier); > + atmel_uart_writel(port, ATMEL_US_IER, ier); > } > > /* > @@ -577,7 +563,7 @@ static void atmel_disable_ms(struct uart_port *port) > else > idr |= ATMEL_US_DCDIC; > > - UART_PUT_IDR(port, idr); > + atmel_uart_writel(port, ATMEL_US_IDR, idr); > } > > /* > @@ -586,9 +572,11 @@ static void atmel_disable_ms(struct uart_port *port) > static void atmel_break_ctl(struct uart_port *port, int break_state) > { > if (break_state != 0) > - UART_PUT_CR(port, ATMEL_US_STTBRK); /* start break */ > + /* start break */ > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTBRK); > else > - UART_PUT_CR(port, ATMEL_US_STPBRK); /* stop break */ > + /* stop break */ > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STPBRK); > } > > /* > @@ -622,7 +610,7 @@ atmel_buffer_rx_char(struct uart_port *port, unsigned int status, > static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status) > { > /* clear error */ > - UART_PUT_CR(port, ATMEL_US_RSTSTA); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); > > if (status & ATMEL_US_RXBRK) { > /* ignore side-effect */ > @@ -645,9 +633,9 @@ static void atmel_rx_chars(struct uart_port *port) > struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); > unsigned int status, ch; > > - status = UART_GET_CSR(port); > + status = atmel_uart_readl(port, ATMEL_US_CSR); > while (status & ATMEL_US_RXRDY) { > - ch = UART_GET_CHAR(port); > + ch = atmel_uart_readl(port, ATMEL_US_RHR); > > /* > * note that the error handling code is > @@ -658,12 +646,13 @@ static void atmel_rx_chars(struct uart_port *port) > || atmel_port->break_active)) { > > /* clear error */ > - UART_PUT_CR(port, ATMEL_US_RSTSTA); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); > > if (status & ATMEL_US_RXBRK > && !atmel_port->break_active) { > atmel_port->break_active = 1; > - UART_PUT_IER(port, ATMEL_US_RXBRK); > + atmel_uart_writel(port, ATMEL_US_IER, > + ATMEL_US_RXBRK); > } else { > /* > * This is either the end-of-break > @@ -672,14 +661,15 @@ static void atmel_rx_chars(struct uart_port *port) > * being set. In both cases, the next > * RXBRK will indicate start-of-break. > */ > - UART_PUT_IDR(port, ATMEL_US_RXBRK); > + atmel_uart_writel(port, ATMEL_US_IDR, > + ATMEL_US_RXBRK); > status &= ~ATMEL_US_RXBRK; > atmel_port->break_active = 0; > } > } > > atmel_buffer_rx_char(port, status, ch); > - status = UART_GET_CSR(port); > + status = atmel_uart_readl(port, ATMEL_US_CSR); > } > > tasklet_schedule(&atmel_port->tasklet); > @@ -694,16 +684,18 @@ static void atmel_tx_chars(struct uart_port *port) > struct circ_buf *xmit = &port->state->xmit; > struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); > > - if (port->x_char && UART_GET_CSR(port) & atmel_port->tx_done_mask) { > - UART_PUT_CHAR(port, port->x_char); > + if (port->x_char && > + (atmel_uart_readl(port, ATMEL_US_CSR) & atmel_port->tx_done_mask)) { > + atmel_uart_writel(port, ATMEL_US_THR, port->x_char); > port->icount.tx++; > port->x_char = 0; > } > if (uart_circ_empty(xmit) || uart_tx_stopped(port)) > return; > > - while (UART_GET_CSR(port) & atmel_port->tx_done_mask) { > - UART_PUT_CHAR(port, xmit->buf[xmit->tail]); > + while (atmel_uart_readl(port, ATMEL_US_CSR) & > + atmel_port->tx_done_mask) { > + atmel_uart_writel(port, ATMEL_US_THR, xmit->buf[xmit->tail]); > xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); > port->icount.tx++; > if (uart_circ_empty(xmit)) > @@ -715,7 +707,8 @@ static void atmel_tx_chars(struct uart_port *port) > > if (!uart_circ_empty(xmit)) > /* Enable interrupts */ > - UART_PUT_IER(port, atmel_port->tx_done_mask); > + atmel_uart_writel(port, ATMEL_US_IER, > + atmel_port->tx_done_mask); > } > > static void atmel_complete_tx_dma(void *arg) > @@ -935,14 +928,14 @@ static void atmel_rx_from_dma(struct uart_port *port) > > > /* Reset the UART timeout early so that we don't miss one */ > - UART_PUT_CR(port, ATMEL_US_STTTO); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); > dmastat = dmaengine_tx_status(chan, > atmel_port->cookie_rx, > &state); > /* Restart a new tasklet if DMA status is error */ > if (dmastat == DMA_ERROR) { > dev_dbg(port->dev, "Get residue error, restart tasklet\n"); > - UART_PUT_IER(port, ATMEL_US_TIMEOUT); > + atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT); > tasklet_schedule(&atmel_port->tasklet); > return; > } > @@ -1008,7 +1001,7 @@ static void atmel_rx_from_dma(struct uart_port *port) > tty_flip_buffer_push(tport); > spin_lock(&port->lock); > > - UART_PUT_IER(port, ATMEL_US_TIMEOUT); > + atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT); > } > > static int atmel_prepare_rx_dma(struct uart_port *port) > @@ -1118,8 +1111,8 @@ atmel_handle_receive(struct uart_port *port, unsigned int pending) > * the moment. > */ > if (pending & (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)) { > - UART_PUT_IDR(port, (ATMEL_US_ENDRX > - | ATMEL_US_TIMEOUT)); > + atmel_uart_writel(port, ATMEL_US_IDR, > + (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)); > tasklet_schedule(&atmel_port->tasklet); > } > > @@ -1130,7 +1123,8 @@ atmel_handle_receive(struct uart_port *port, unsigned int pending) > > if (atmel_use_dma_rx(port)) { > if (pending & ATMEL_US_TIMEOUT) { > - UART_PUT_IDR(port, ATMEL_US_TIMEOUT); > + atmel_uart_writel(port, ATMEL_US_IDR, > + ATMEL_US_TIMEOUT); > tasklet_schedule(&atmel_port->tasklet); > } > } > @@ -1143,8 +1137,8 @@ atmel_handle_receive(struct uart_port *port, unsigned int pending) > * End of break detected. If it came along with a > * character, atmel_rx_chars will handle it. > */ > - UART_PUT_CR(port, ATMEL_US_RSTSTA); > - UART_PUT_IDR(port, ATMEL_US_RXBRK); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); > + atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXBRK); > atmel_port->break_active = 0; > } > } > @@ -1159,7 +1153,8 @@ atmel_handle_transmit(struct uart_port *port, unsigned int pending) > > if (pending & atmel_port->tx_done_mask) { > /* Either PDC or interrupt transmission */ > - UART_PUT_IDR(port, atmel_port->tx_done_mask); > + atmel_uart_writel(port, ATMEL_US_IDR, > + atmel_port->tx_done_mask); > tasklet_schedule(&atmel_port->tasklet); > } > } > @@ -1197,7 +1192,7 @@ static irqreturn_t atmel_interrupt(int irq, void *dev_id) > > do { > status = atmel_get_lines_status(port); > - mask = UART_GET_IMR(port); > + mask = atmel_uart_readl(port, ATMEL_US_IMR); > pending = status & mask; > if (!gpio_handled) { > /* > @@ -1223,7 +1218,7 @@ static irqreturn_t atmel_interrupt(int irq, void *dev_id) > if (atmel_port->suspended) { > atmel_port->pending |= pending; > atmel_port->pending_status = status; > - UART_PUT_IDR(port, mask); > + atmel_uart_writel(port, ATMEL_US_IDR, mask); > pm_system_wakeup(); > break; > } > @@ -1260,7 +1255,7 @@ static void atmel_tx_pdc(struct uart_port *port) > int count; > > /* nothing left to transmit? */ > - if (UART_GET_TCR(port)) > + if (atmel_uart_readl(port, ATMEL_PDC_TCR)) > return; > > xmit->tail += pdc->ofs; > @@ -1272,7 +1267,7 @@ static void atmel_tx_pdc(struct uart_port *port) > /* more to transmit - setup next transfer */ > > /* disable PDC transmit */ > - UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS); > + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS); > > if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) { > dma_sync_single_for_device(port->dev, > @@ -1283,12 +1278,14 @@ static void atmel_tx_pdc(struct uart_port *port) > count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); > pdc->ofs = count; > > - UART_PUT_TPR(port, pdc->dma_addr + xmit->tail); > - UART_PUT_TCR(port, count); > + atmel_uart_writel(port, ATMEL_PDC_TPR, > + pdc->dma_addr + xmit->tail); > + atmel_uart_writel(port, ATMEL_PDC_TCR, count); > /* re-enable PDC transmit */ > - UART_PUT_PTCR(port, ATMEL_PDC_TXTEN); > + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); > /* Enable interrupts */ > - UART_PUT_IER(port, atmel_port->tx_done_mask); > + atmel_uart_writel(port, ATMEL_US_IER, > + atmel_port->tx_done_mask); > } else { > if ((port->rs485.flags & SER_RS485_ENABLED) && > !(port->rs485.flags & SER_RS485_RX_DURING_TX)) { > @@ -1414,10 +1411,10 @@ static void atmel_rx_from_pdc(struct uart_port *port) > > do { > /* Reset the UART timeout early so that we don't miss one */ > - UART_PUT_CR(port, ATMEL_US_STTTO); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); > > pdc = &atmel_port->pdc_rx[rx_idx]; > - head = UART_GET_RPR(port) - pdc->dma_addr; > + head = atmel_uart_readl(port, ATMEL_PDC_RPR) - pdc->dma_addr; > tail = pdc->ofs; > > /* If the PDC has switched buffers, RPR won't contain > @@ -1460,8 +1457,8 @@ static void atmel_rx_from_pdc(struct uart_port *port) > */ > if (head >= pdc->dma_size) { > pdc->ofs = 0; > - UART_PUT_RNPR(port, pdc->dma_addr); > - UART_PUT_RNCR(port, pdc->dma_size); > + atmel_uart_writel(port, ATMEL_PDC_RNPR, pdc->dma_addr); > + atmel_uart_writel(port, ATMEL_PDC_RNCR, pdc->dma_size); > > rx_idx = !rx_idx; > atmel_port->pdc_rx_idx = rx_idx; > @@ -1476,7 +1473,8 @@ static void atmel_rx_from_pdc(struct uart_port *port) > tty_flip_buffer_push(tport); > spin_lock(&port->lock); > > - UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT); > + atmel_uart_writel(port, ATMEL_US_IER, > + ATMEL_US_ENDRX | ATMEL_US_TIMEOUT); > } > > static int atmel_prepare_rx_pdc(struct uart_port *port) > @@ -1509,11 +1507,12 @@ static int atmel_prepare_rx_pdc(struct uart_port *port) > > atmel_port->pdc_rx_idx = 0; > > - UART_PUT_RPR(port, atmel_port->pdc_rx[0].dma_addr); > - UART_PUT_RCR(port, PDC_BUFFER_SIZE); > + atmel_uart_writel(port, ATMEL_PDC_RPR, atmel_port->pdc_rx[0].dma_addr); > + atmel_uart_writel(port, ATMEL_PDC_RCR, PDC_BUFFER_SIZE); > > - UART_PUT_RNPR(port, atmel_port->pdc_rx[1].dma_addr); > - UART_PUT_RNCR(port, PDC_BUFFER_SIZE); > + atmel_uart_writel(port, ATMEL_PDC_RNPR, > + atmel_port->pdc_rx[1].dma_addr); > + atmel_uart_writel(port, ATMEL_PDC_RNCR, PDC_BUFFER_SIZE); > > return 0; > } > @@ -1667,7 +1666,7 @@ static void atmel_set_ops(struct uart_port *port) > static void atmel_get_ip_name(struct uart_port *port) > { > struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); > - int name = UART_GET_IP_NAME(port); > + int name = atmel_uart_readl(port, ATMEL_US_NAME); > u32 version; > int usart, uart; > /* usart and uart ascii */ > @@ -1684,7 +1683,7 @@ static void atmel_get_ip_name(struct uart_port *port) > atmel_port->is_usart = false; > } else { > /* fallback for older SoCs: use version field */ > - version = UART_GET_IP_VERSION(port); > + version = atmel_uart_readl(port, ATMEL_US_VERSION); > switch (version) { > case 0x302: > case 0x10213: > @@ -1756,7 +1755,7 @@ static int atmel_startup(struct uart_port *port) > * request_irq() is called we could get stuck trying to > * handle an unexpected interrupt > */ > - UART_PUT_IDR(port, -1); > + atmel_uart_writel(port, ATMEL_US_IDR, -1); > atmel_port->ms_irq_enabled = false; > > /* > @@ -1804,9 +1803,9 @@ static int atmel_startup(struct uart_port *port) > /* > * Finally, enable the serial port > */ > - UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); > /* enable xmit & rcvr */ > - UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN); > > setup_timer(&atmel_port->uart_timer, > atmel_uart_timer_callback, > @@ -1819,13 +1818,14 @@ static int atmel_startup(struct uart_port *port) > jiffies + uart_poll_timeout(port)); > /* set USART timeout */ > } else { > - UART_PUT_RTOR(port, PDC_RX_TIMEOUT); > - UART_PUT_CR(port, ATMEL_US_STTTO); > + atmel_uart_writel(port, ATMEL_US_RTOR, PDC_RX_TIMEOUT); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); > > - UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT); > + atmel_uart_writel(port, ATMEL_US_IER, > + ATMEL_US_ENDRX | ATMEL_US_TIMEOUT); > } > /* enable PDC controller */ > - UART_PUT_PTCR(port, ATMEL_PDC_RXTEN); > + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN); > } else if (atmel_use_dma_rx(port)) { > /* set UART timeout */ > if (!atmel_port->is_usart) { > @@ -1833,14 +1833,15 @@ static int atmel_startup(struct uart_port *port) > jiffies + uart_poll_timeout(port)); > /* set USART timeout */ > } else { > - UART_PUT_RTOR(port, PDC_RX_TIMEOUT); > - UART_PUT_CR(port, ATMEL_US_STTTO); > + atmel_uart_writel(port, ATMEL_US_RTOR, PDC_RX_TIMEOUT); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); > > - UART_PUT_IER(port, ATMEL_US_TIMEOUT); > + atmel_uart_writel(port, ATMEL_US_IER, > + ATMEL_US_TIMEOUT); > } > } else { > /* enable receive only */ > - UART_PUT_IER(port, ATMEL_US_RXRDY); > + atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY); > } > > return 0; > @@ -1860,7 +1861,7 @@ static void atmel_flush_buffer(struct uart_port *port) > struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); > > if (atmel_use_pdc_tx(port)) { > - UART_PUT_TCR(port, 0); > + atmel_uart_writel(port, ATMEL_PDC_TCR, 0); > atmel_port->pdc_tx.ofs = 0; > } > } > @@ -1892,8 +1893,8 @@ static void atmel_shutdown(struct uart_port *port) > atmel_stop_rx(port); > atmel_stop_tx(port); > > - UART_PUT_CR(port, ATMEL_US_RSTSTA); > - UART_PUT_IDR(port, -1); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); > + atmel_uart_writel(port, ATMEL_US_IDR, -1); > > > /* > @@ -1938,12 +1939,12 @@ static void atmel_serial_pm(struct uart_port *port, unsigned int state, > clk_prepare_enable(atmel_port->clk); > > /* re-enable interrupts if we disabled some on suspend */ > - UART_PUT_IER(port, atmel_port->backup_imr); > + atmel_uart_writel(port, ATMEL_US_IER, atmel_port->backup_imr); > break; > case 3: > /* Back up the interrupt mask and disable all interrupts */ > - atmel_port->backup_imr = UART_GET_IMR(port); > - UART_PUT_IDR(port, -1); > + atmel_port->backup_imr = atmel_uart_readl(port, ATMEL_US_IMR); > + atmel_uart_writel(port, ATMEL_US_IDR, -1); > > /* > * Disable the peripheral clock for this serial port. > @@ -1966,7 +1967,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios, > unsigned int old_mode, mode, imr, quot, baud; > > /* save the current mode register */ > - mode = old_mode = UART_GET_MR(port); > + mode = old_mode = atmel_uart_readl(port, ATMEL_US_MR); > > /* reset the mode, clock divisor, parity, stop bits and data size */ > mode &= ~(ATMEL_US_USCLKS | ATMEL_US_CHRL | ATMEL_US_NBSTOP | > @@ -2025,7 +2026,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios, > > if (atmel_use_pdc_rx(port)) > /* need to enable error interrupts */ > - UART_PUT_IER(port, port->read_status_mask); > + atmel_uart_writel(port, ATMEL_US_IER, port->read_status_mask); > > /* > * Characters to ignore > @@ -2052,15 +2053,16 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios, > * transmitter is empty if requested by the caller, so there's > * no need to wait for it here. > */ > - imr = UART_GET_IMR(port); > - UART_PUT_IDR(port, -1); > + imr = atmel_uart_readl(port, ATMEL_US_IMR); > + atmel_uart_writel(port, ATMEL_US_IDR, -1); > > /* disable receiver and transmitter */ > - UART_PUT_CR(port, ATMEL_US_TXDIS | ATMEL_US_RXDIS); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXDIS); > > /* mode */ > if (port->rs485.flags & SER_RS485_ENABLED) { > - UART_PUT_TTGR(port, port->rs485.delay_rts_after_send); > + atmel_uart_writel(port, ATMEL_US_TTGR, > + port->rs485.delay_rts_after_send); > mode |= ATMEL_US_USMODE_RS485; > } else if (termios->c_cflag & CRTSCTS) { > /* RS232 with hardware handshake (RTS/CTS) */ > @@ -2071,7 +2073,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios, > } > > /* set the mode, clock divisor, parity, stop bits and data size */ > - UART_PUT_MR(port, mode); > + atmel_uart_writel(port, ATMEL_US_MR, mode); > > /* > * when switching the mode, set the RTS line state according to the > @@ -2088,16 +2090,16 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios, > rts_state = ATMEL_US_RTSEN; > } > > - UART_PUT_CR(port, rts_state); > + atmel_uart_writel(port, ATMEL_US_CR, rts_state); > } > > /* set the baud rate */ > - UART_PUT_BRGR(port, quot); > - UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); > - UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN); > + atmel_uart_writel(port, ATMEL_US_BRGR, quot); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN); > > /* restore interrupts */ > - UART_PUT_IER(port, imr); > + atmel_uart_writel(port, ATMEL_US_IER, imr); > > /* CTS flow-control and modem-status interrupts */ > if (UART_ENABLE_MS(port, termios->c_cflag)) > @@ -2208,18 +2210,18 @@ static int atmel_verify_port(struct uart_port *port, struct serial_struct *ser) > #ifdef CONFIG_CONSOLE_POLL > static int atmel_poll_get_char(struct uart_port *port) > { > - while (!(UART_GET_CSR(port) & ATMEL_US_RXRDY)) > + while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_RXRDY)) > cpu_relax(); > > - return UART_GET_CHAR(port); > + return atmel_uart_readl(port, ATMEL_US_RHR); > } > > static void atmel_poll_put_char(struct uart_port *port, unsigned char ch) > { > - while (!(UART_GET_CSR(port) & ATMEL_US_TXRDY)) > + while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY)) > cpu_relax(); > > - UART_PUT_CHAR(port, ch); > + atmel_uart_writel(port, ATMEL_US_THR, ch); > } > #endif > > @@ -2324,9 +2326,9 @@ struct platform_device *atmel_default_console_device; /* the serial console devi > #ifdef CONFIG_SERIAL_ATMEL_CONSOLE > static void atmel_console_putchar(struct uart_port *port, int ch) > { > - while (!(UART_GET_CSR(port) & ATMEL_US_TXRDY)) > + while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY)) > cpu_relax(); > - UART_PUT_CHAR(port, ch); > + atmel_uart_writel(port, ATMEL_US_THR, ch); > } > > /* > @@ -2342,12 +2344,13 @@ static void atmel_console_write(struct console *co, const char *s, u_int count) > /* > * First, save IMR and then disable interrupts > */ > - imr = UART_GET_IMR(port); > - UART_PUT_IDR(port, ATMEL_US_RXRDY | atmel_port->tx_done_mask); > + imr = atmel_uart_readl(port, ATMEL_US_IMR); > + atmel_uart_writel(port, ATMEL_US_IDR, > + ATMEL_US_RXRDY | atmel_port->tx_done_mask); > > /* Store PDC transmit status and disable it */ > - pdc_tx = UART_GET_PTSR(port) & ATMEL_PDC_TXTEN; > - UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS); > + pdc_tx = atmel_uart_readl(port, ATMEL_PDC_PTSR) & ATMEL_PDC_TXTEN; > + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS); > > uart_console_write(port, s, count, atmel_console_putchar); > > @@ -2356,15 +2359,15 @@ static void atmel_console_write(struct console *co, const char *s, u_int count) > * and restore IMR > */ > do { > - status = UART_GET_CSR(port); > + status = atmel_uart_readl(port, ATMEL_US_CSR); > } while (!(status & ATMEL_US_TXRDY)); > > /* Restore PDC transmit status */ > if (pdc_tx) > - UART_PUT_PTCR(port, ATMEL_PDC_TXTEN); > + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); > > /* set interrupts back the way they were */ > - UART_PUT_IER(port, imr); > + atmel_uart_writel(port, ATMEL_US_IER, imr); > } > > /* > @@ -2380,17 +2383,17 @@ static void __init atmel_console_get_options(struct uart_port *port, int *baud, > * If the baud rate generator isn't running, the port wasn't > * initialized by the boot loader. > */ > - quot = UART_GET_BRGR(port) & ATMEL_US_CD; > + quot = atmel_uart_readl(port, ATMEL_US_BRGR) & ATMEL_US_CD; > if (!quot) > return; > > - mr = UART_GET_MR(port) & ATMEL_US_CHRL; > + mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_CHRL; > if (mr == ATMEL_US_CHRL_8) > *bits = 8; > else > *bits = 7; > > - mr = UART_GET_MR(port) & ATMEL_US_PAR; > + mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_PAR; > if (mr == ATMEL_US_PAR_EVEN) > *parity = 'e'; > else if (mr == ATMEL_US_PAR_ODD) > @@ -2423,9 +2426,9 @@ static int __init atmel_console_setup(struct console *co, char *options) > if (ret) > return ret; > > - UART_PUT_IDR(port, -1); > - UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); > - UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN); > + atmel_uart_writel(port, ATMEL_US_IDR, -1); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); > + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN); > > if (options) > uart_parse_options(options, &baud, &parity, &bits, &flow); > @@ -2532,7 +2535,8 @@ static int atmel_serial_suspend(struct platform_device *pdev, > > if (atmel_is_console_port(port) && console_suspend_enabled) { > /* Drain the TX shifter */ > - while (!(UART_GET_CSR(port) & ATMEL_US_TXEMPTY)) > + while (!(atmel_uart_readl(port, ATMEL_US_CSR) & > + ATMEL_US_TXEMPTY)) > cpu_relax(); > } > > @@ -2684,8 +2688,9 @@ static int atmel_serial_probe(struct platform_device *pdev) > clk_prepare_enable(port->clk); > > if (rs485_enabled) { > - UART_PUT_MR(&port->uart, ATMEL_US_USMODE_NORMAL); > - UART_PUT_CR(&port->uart, ATMEL_US_RTSEN); > + atmel_uart_writel(&port->uart, ATMEL_US_MR, > + ATMEL_US_USMODE_NORMAL); > + atmel_uart_writel(&port->uart, ATMEL_US_CR, ATMEL_US_RTSEN); > } > > /* > -- Nicolas Ferre -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/