Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id ; Mon, 17 Feb 2003 09:29:49 -0500 Received: (majordomo@vger.kernel.org) by vger.kernel.org id ; Mon, 17 Feb 2003 09:12:05 -0500 Received: from chii.cinet.co.jp ([61.197.228.217]:28032 "EHLO yuzuki.cinet.co.jp") by vger.kernel.org with ESMTP id ; Mon, 17 Feb 2003 09:07:49 -0500 Date: Mon, 17 Feb 2003 23:15:52 +0900 From: Osamu Tomita To: Linux Kernel Mailing List Cc: Jeff Garzik , Alan Cox , "'Christoph Hellwig'" Subject: [PATCHSET] PC-9800 subarch. support for 2.5.61 (16/26) NIC Message-ID: <20030217141552.GP4799@yuzuki.cinet.co.jp> References: <20030217134333.GA4734@yuzuki.cinet.co.jp> Mime-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Disposition: inline In-Reply-To: <20030217134333.GA4734@yuzuki.cinet.co.jp> User-Agent: Mutt/1.4i Sender: linux-kernel-owner@vger.kernel.org X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 47478 Lines: 1616 This is patchset to support NEC PC-9800 subarchitecture against 2.5.61 (16/26). C-bus(PC98's legacy bus like ISA) network cards support. diff -Nru linux-2.5.61/drivers/net/3c509.c linux98-2.5.61/drivers/net/3c509.c --- linux-2.5.61/drivers/net/3c509.c 2003-02-15 08:51:09.000000000 +0900 +++ linux98-2.5.61/drivers/net/3c509.c 2003-02-15 14:38:08.000000000 +0900 @@ -56,6 +56,10 @@ v1.19b 08Nov2002 Marc Zyngier - Introduce driver model for EISA cards. */ +/* + FIXES for PC-9800: + Shu Iwanaga: 3c569B(PC-9801 C-bus) support +*/ #define DRV_NAME "3c509" #define DRV_VERSION "1.19b" @@ -257,7 +261,7 @@ }; #endif /* CONFIG_MCA */ -#ifdef __ISAPNP__ +#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800) static struct isapnp_device_id el3_isapnp_adapters[] __initdata = { { ISAPNP_ANY_ID, ISAPNP_ANY_ID, ISAPNP_VENDOR('T', 'C', 'M'), ISAPNP_FUNCTION(0x5090), @@ -350,7 +354,7 @@ if (lp->pmdev) pm_unregister(lp->pmdev); #endif -#ifdef __ISAPNP__ +#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800) if (lp->type == EL3_PNP) pnp_device_detach(to_pnp_dev(lp->dev)); #endif @@ -368,12 +372,12 @@ int ioaddr, irq, if_port; u16 phys_addr[3]; static int current_tag; -#ifdef __ISAPNP__ +#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800) static int pnp_cards; struct pnp_dev *idev = NULL; #endif /* __ISAPNP__ */ -#ifdef __ISAPNP__ +#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800) if (nopnp == 1) goto no_pnp; @@ -421,6 +425,9 @@ no_pnp: #endif /* __ISAPNP__ */ +#ifdef CONFIG_X86_PC9800 + id_port = 0x71d0; +#else /* Select an open I/O location at 0x1*0 to do contention select. */ for ( ; id_port < 0x200; id_port += 0x10) { if (check_region(id_port, 1)) @@ -435,6 +442,7 @@ printk(" WARNING: No I/O port available for 3c509 activation.\n"); return -ENODEV; } +#endif /* CONFIG_X86_PC9800 */ /* Next check for all ISA bus boards by sending the ID sequence to the ID_PORT. We find cards past the first by setting the 'current_tag' on cards as they are found. Cards with their tag set will not @@ -465,7 +473,7 @@ phys_addr[i] = htons(id_read_eeprom(i)); } -#ifdef __ISAPNP__ +#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800) if (nopnp == 0) { /* The ISA PnP 3c509 cards respond to the ID sequence. This check is needed in order not to register them twice. */ @@ -490,9 +498,19 @@ { unsigned int iobase = id_read_eeprom(8); if_port = iobase >> 14; +#ifdef CONFIG_X86_PC9800 + ioaddr = 0x40d0 + ((iobase & 0x1f) << 8); +#else ioaddr = 0x200 + ((iobase & 0x1f) << 4); +#endif } irq = id_read_eeprom(9) >> 12; +#ifdef CONFIG_X86_PC9800 + if (irq == 7) + irq = 6; + else if (irq == 15) + irq = 13; +#endif if (!(dev = init_etherdev(NULL, sizeof(struct el3_private)))) return -ENOMEM; @@ -522,7 +540,11 @@ outb(0xd0 + ++current_tag, id_port); /* Activate the adaptor at the EEPROM location. */ +#ifdef CONFIG_X86_PC9800 + outb((ioaddr >> 8) | 0xe0, id_port); +#else outb((ioaddr >> 4) | 0xe0, id_port); +#endif EL3WINDOW(0); if (inw(ioaddr) != 0x6d50) { @@ -534,7 +556,7 @@ /* Free the interrupt so that some other card can use it. */ outw(0x0f00, ioaddr + WN0_IRQ); -#ifdef __ISAPNP__ +#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800) found: /* PNP jumps here... */ #endif /* __ISAPNP__ */ @@ -543,7 +565,7 @@ dev->irq = irq; dev->if_port = if_port; lp = dev->priv; -#ifdef __ISAPNP__ +#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800) lp->dev = &idev->dev; #endif @@ -1388,6 +1410,12 @@ outw(0x0001, ioaddr + 4); /* Set the IRQ line. */ +#ifdef CONFIG_X86_PC9800 + if (dev->irq == 6) + dev->irq = 7; + else if (dev->irq == 13) + dev->irq = 15; +#endif outw((dev->irq << 12) | 0x0f00, ioaddr + WN0_IRQ); /* Set the station address in window 2 each time opened. */ @@ -1550,7 +1578,7 @@ MODULE_PARM_DESC(irq, "IRQ number(s) (assigned)"); MODULE_PARM_DESC(xcvr,"tranceiver(s) (0=internal, 1=external)"); MODULE_PARM_DESC(max_interrupt_work, "maximum events handled per interrupt"); -#ifdef __ISAPNP__ +#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800) MODULE_PARM(nopnp, "i"); MODULE_PARM_DESC(nopnp, "disable ISA PnP support (0-1)"); MODULE_DEVICE_TABLE(isapnp, el3_isapnp_adapters); diff -Nru linux-2.5.42/drivers/net/8390.h linux98-2.5.42/drivers/net/8390.h --- linux-2.5.42/drivers/net/8390.h 2002-10-12 13:22:14.000000000 +0900 +++ linux98-2.5.42/drivers/net/8390.h 2002-10-15 23:03:22.000000000 +0900 @@ -123,7 +123,8 @@ #define inb_p(port) in_8(port) #define outb_p(val,port) out_8(port,val) -#elif defined(CONFIG_ARM_ETHERH) || defined(CONFIG_ARM_ETHERH_MODULE) +#elif defined(CONFIG_ARM_ETHERH) || defined(CONFIG_ARM_ETHERH_MODULE) || \ + defined(CONFIG_NET_CBUS) #define EI_SHIFT(x) (ei_local->reg_offset[x]) #else #define EI_SHIFT(x) (x) diff -Nru linux-2.5.61/drivers/net/Kconfig linux98-2.5.61/drivers/net/Kconfig --- linux-2.5.61/drivers/net/Kconfig 2003-02-15 08:52:31.000000000 +0900 +++ linux98-2.5.61/drivers/net/Kconfig 2003-02-15 14:24:25.000000000 +0900 @@ -662,7 +662,7 @@ as . config EL3 - tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support" + tristate "3c509/3c529 (MCA)/3c569B (98)/3c579 \"EtherLink III\" support" depends on NET_VENDOR_3COM && (ISA || EISA || MCA) ---help--- If you have a network (Ethernet) card belonging to the 3Com @@ -931,7 +931,7 @@ source "drivers/net/tulip/Kconfig" config AT1700 - tristate "AT1700/1720 support (EXPERIMENTAL)" + tristate "AT1700/1720/RE1000Plus(C-Bus) support (EXPERIMENTAL)" depends on NET_ETHERNET && (ISA || MCA) && EXPERIMENTAL ---help--- If you have a network (Ethernet) card of this type, say Y and read @@ -977,7 +977,7 @@ config NET_ISA bool "Other ISA cards" - depends on NET_ETHERNET && ISA + depends on NET_ETHERNET && ISA && !X86_PC9800 ---help--- If your network (Ethernet) card hasn't been mentioned yet and its bus system (that's the way the cards talks to the other components @@ -1175,6 +1175,55 @@ the Ethernet-HOWTO, available from . +config NET_CBUS + bool "NEC PC-9800 C-bus cards" + depends on NET_ETHERNET && ISA && X86_PC9800 + ---help--- + If your network (Ethernet) card hasn't been mentioned yet and its + bus system (that's the way the cards talks to the other components + of your computer) is NEC PC-9800 C-Bus, say Y. + +config NE2K_CBUS + tristate "Most NE2000-based Ethernet support" + depends on NET_CBUS + +config NE2K_CBUS_EGY98 + bool "Melco EGY-98 support" + depends on NE2K_CBUS + +config NE2K_CBUS_LGY98 + bool "Melco LGY-98 support" + depends on NE2K_CBUS + +config NE2K_CBUS_ICM + bool "ICM IF-27xxET support" + depends on NE2K_CBUS + +config NE2K_CBUS_IOLA98 + bool "I-O DATA LA-98 support" + depends on NE2K_CBUS + +config NE2K_CBUS_CNET98EL + bool "Contec C-NET(98)E/L support" + depends on NE2K_CBUS + +config NE2K_CBUS_CNET98EL_IO_BASE + hex "C-NET(98)E/L I/O base address (0xaaed or 0x55ed)" + depends on NE2K_CBUS_CNET98EL + default "0xaaed" + +config NE2K_CBUS_ATLA98 + bool "Allied Telesis LA-98 Support" + depends on NE2K_CBUS + +config NE2K_CBUS_BDN + bool "ELECOM Laneed LD-BDN[123]A Support" + depends on NE2K_CBUS + +config NE2K_CBUS_NEC108 + bool "NEC PC-9801-108 Support" + depends on NE2K_CBUS + config SKMC tristate "SKnet MCA support" depends on NET_ETHERNET && MCA diff -Nru linux-2.5.61/drivers/net/Makefile linux98-2.5.61/drivers/net/Makefile --- linux-2.5.61/drivers/net/Makefile 2003-02-15 08:51:25.000000000 +0900 +++ linux98-2.5.61/drivers/net/Makefile 2003-02-15 14:24:25.000000000 +0900 @@ -86,6 +86,7 @@ obj-$(CONFIG_WD80x3) += wd.o 8390.o obj-$(CONFIG_EL2) += 3c503.o 8390.o obj-$(CONFIG_NE2000) += ne.o 8390.o +obj-$(CONFIG_NE2K_CBUS) += ne.o 8390.o obj-$(CONFIG_NE2_MCA) += ne2.o 8390.o obj-$(CONFIG_HPLAN) += hp.o 8390.o obj-$(CONFIG_HPLAN_PLUS) += hp-plus.o 8390.o diff -Nru linux-2.5.42/drivers/net/Makefile.lib linux98-2.5.42/drivers/net/Makefile.lib --- linux-2.5.42/drivers/net/Makefile.lib 2002-10-12 13:22:18.000000000 +0900 +++ linux98-2.5.42/drivers/net/Makefile.lib 2002-10-15 23:03:22.000000000 +0900 @@ -19,6 +19,7 @@ obj-$(CONFIG_MACMACE) += crc32.o obj-$(CONFIG_MIPS_AU1000_ENET) += crc32.o obj-$(CONFIG_NATSEMI) += crc32.o +obj-$(CONFIG_NE2K_CBUS) += crc32.o obj-$(CONFIG_PCMCIA_FMVJ18X) += crc32.o obj-$(CONFIG_PCMCIA_SMC91C92) += crc32.o obj-$(CONFIG_PCMCIA_XIRTULIP) += crc32.o diff -Nru linux-2.5.61/drivers/net/Space.c linux98-2.5.61/drivers/net/Space.c --- linux-2.5.61/drivers/net/Space.c 2003-02-15 08:51:12.000000000 +0900 +++ linux98-2.5.61/drivers/net/Space.c 2003-02-15 14:24:25.000000000 +0900 @@ -233,7 +233,7 @@ #ifdef CONFIG_E2100 /* Cabletron E21xx series. */ {e2100_probe, 0}, #endif -#ifdef CONFIG_NE2000 /* ISA (use ne2k-pci for PCI cards) */ +#if defined(CONFIG_NE2000) || defined(CONFIG_NE2K_CBUS) /* ISA & PC-9800 CBUS (use ne2k-pci for PCI cards) */ {ne_probe, 0}, #endif #ifdef CONFIG_LANCE /* ISA/VLB (use pcnet32 for PCI cards) */ diff -Nru linux-2.5.57/drivers/net/at1700.c linux98-2.5.57/drivers/net/at1700.c --- linux-2.5.57/drivers/net/at1700.c 2003-01-14 09:31:51.000000000 +0900 +++ linux98-2.5.57/drivers/net/at1700.c 2003-01-14 09:55:53.000000000 +0900 @@ -34,6 +34,10 @@ only is it difficult to detect, it also moves around in I/O space in response to inb()s from other device probes! */ +/* + 99/03/03 Allied Telesis RE1000 Plus support by T.Hagawa + 99/12/30 port to 2.3.35 by K.Takai +*/ #include #include @@ -76,10 +80,17 @@ * ISA */ +#ifndef CONFIG_X86_PC9800 static int at1700_probe_list[] __initdata = { 0x260, 0x280, 0x2a0, 0x240, 0x340, 0x320, 0x380, 0x300, 0 }; +#else /* CONFIG_X86_PC9800 */ +static int at1700_probe_list[] __initdata = { + 0x1d6, 0x1d8, 0x1da, 0x1d4, 0xd4, 0xd2, 0xd8, 0xd0, 0 +}; + +#endif /* CONFIG_X86_PC9800 */ /* * MCA */ @@ -122,6 +133,7 @@ /* Offsets from the base address. */ +#ifndef CONFIG_X86_PC9800 #define STATUS 0 #define TX_STATUS 0 #define RX_STATUS 1 @@ -136,6 +148,7 @@ #define TX_START 10 #define COL16CNTL 11 /* Controll Reg for 16 collisions */ #define MODE13 13 +#define RX_CTRL 14 /* Configuration registers only on the '865A/B chips. */ #define EEPROM_Ctrl 16 #define EEPROM_Data 17 @@ -144,8 +157,39 @@ #define IOCONFIG 18 /* Either read the jumper, or move the I/O. */ #define IOCONFIG1 19 #define SAPROM 20 /* The station address PROM, if no EEPROM. */ +#define MODE24 24 #define RESET 31 /* Write to reset some parts of the chip. */ #define AT1700_IO_EXTENT 32 +#define PORT_OFFSET(o) (o) +#else /* CONFIG_X86_PC9800 */ +#define STATUS (0x0000) +#define TX_STATUS (0x0000) +#define RX_STATUS (0x0001) +#define TX_INTR (0x0200)/* Bit-mapped interrupt enable registers. */ +#define RX_INTR (0x0201) +#define TX_MODE (0x0400) +#define RX_MODE (0x0401) +#define CONFIG_0 (0x0600)/* Misc. configuration settings. */ +#define CONFIG_1 (0x0601) +/* Run-time register bank 2 definitions. */ +#define DATAPORT (0x0800)/* Word-wide DMA or programmed-I/O dataport. */ +#define TX_START (0x0a00) +#define COL16CNTL (0x0a01)/* Controll Reg for 16 collisions */ +#define MODE13 (0x0c01) +#define RX_CTRL (0x0e00) +/* Configuration registers only on the '865A/B chips. */ +#define EEPROM_Ctrl (0x1000) +#define EEPROM_Data (0x1200) +#define CARDSTATUS 16 /* FMV-18x Card Status */ +#define CARDSTATUS1 17 /* FMV-18x Card Status */ +#define IOCONFIG (0x1400)/* Either read the jumper, or move the I/O. */ +#define IOCONFIG1 (0x1600) +#define SAPROM 20 /* The station address PROM, if no EEPROM. */ +#define MODE24 (0x1800)/* The station address PROM, if no EEPROM. */ +#define RESET (0x1e01)/* Write to reset some parts of the chip. */ +#define PORT_OFFSET(o) ({ int _o_ = (o); (_o_ & ~1) * 0x100 + (_o_ & 1); }) +#endif /* CONFIG_X86_PC9800 */ + #define TX_TIMEOUT 10 @@ -225,8 +269,20 @@ int slot, ret = -ENODEV; struct net_local *lp; +#ifndef CONFIG_X86_PC9800 if (!request_region(ioaddr, AT1700_IO_EXTENT, dev->name)) return -EBUSY; +#else + for (i = 0; i < 0x2000; i += 0x0200) { + if (!request_region(ioaddr + i, 2, dev->name)) { + while (i > 0) { + i -= 0x0200; + release_region(ioaddr + i, 2); + } + return -EBUSY; + } + } +#endif /* Resetting the chip doesn't reset the ISA interface, so don't bother. That means we have to be careful with the register values we probe for. @@ -317,10 +373,17 @@ /* Reset the internal state machines. */ outb(0, ioaddr + RESET); - if (is_at1700) + if (is_at1700) { +#ifndef CONFIG_X86_PC9800 irq = at1700_irqmap[(read_eeprom(ioaddr, 12)&0x04) | (read_eeprom(ioaddr, 0)>>14)]; - else { +#else + { + char re1000plus_irqmap[4] = {3, 5, 6, 12}; + irq = re1000plus_irqmap[inb(ioaddr + IOCONFIG1) >> 6]; + } +#endif + } else { /* Check PnP mode for FMV-183/184/183A/184A. */ /* This PnP routine is very poor. IO and IRQ should be known. */ if (inb(ioaddr + CARDSTATUS1) & 0x20) { @@ -392,18 +455,22 @@ /* Set the station address in bank zero. */ outb(0x00, ioaddr + CONFIG_1); for (i = 0; i < 6; i++) - outb(dev->dev_addr[i], ioaddr + 8 + i); + outb(dev->dev_addr[i], ioaddr + PORT_OFFSET(8 + i)); /* Switch to bank 1 and set the multicast table to accept none. */ outb(0x04, ioaddr + CONFIG_1); for (i = 0; i < 8; i++) - outb(0x00, ioaddr + 8 + i); + outb(0x00, ioaddr + PORT_OFFSET(8 + i)); /* Switch to bank 2 */ /* Lock our I/O address, and set manual processing mode for 16 collisions. */ outb(0x08, ioaddr + CONFIG_1); +#ifndef CONFIG_X86_PC9800 outb(dev->if_port, ioaddr + MODE13); +#else + outb(0, ioaddr + MODE13); +#endif outb(0x00, ioaddr + COL16CNTL); if (net_debug) @@ -447,7 +514,12 @@ kfree(dev->priv); dev->priv = NULL; err_out: +#ifndef CONFIG_X86_PC9800 release_region(ioaddr, AT1700_IO_EXTENT); +#else + for (i = 0; i < 0x2000; i += 0x0200) + release_region(ioaddr + i, 2); +#endif return ret; } @@ -459,7 +531,11 @@ #define EE_DATA_READ 0x80 /* EEPROM chip data out, in reg. 17. */ /* Delay between EEPROM clock transitions. */ +#ifndef CONFIG_X86_PC9800 #define eeprom_delay() do { } while (0) +#else +#define eeprom_delay() __asm__ ("out%B0 %%al,%0" :: "N"(0x5f)) +#endif /* The EEPROM commands include the alway-set leading bit. */ #define EE_WRITE_CMD (5 << 6) @@ -542,12 +618,12 @@ inw (ioaddr + STATUS), inb (ioaddr + TX_STATUS) & 0x80 ? "IRQ conflict" : "network cable problem"); printk ("%s: timeout registers: %04x %04x %04x %04x %04x %04x %04x %04x.\n", - dev->name, inw (ioaddr + 0), inw (ioaddr + 2), inw (ioaddr + 4), - inw (ioaddr + 6), inw (ioaddr + 8), inw (ioaddr + 10), - inw (ioaddr + 12), inw (ioaddr + 14)); + dev->name, inw(ioaddr + TX_STATUS), inw(ioaddr + TX_INTR), inw(ioaddr + TX_MODE), + inw(ioaddr + CONFIG_0), inw(ioaddr + DATAPORT), inw(ioaddr + TX_START), + inw(ioaddr + MODE13 - 1), inw(ioaddr + RX_CTRL)); lp->stats.tx_errors++; /* ToDo: We should try to restart the adaptor... */ - outw (0xffff, ioaddr + 24); + outw(0xffff, ioaddr + MODE24); outw (0xffff, ioaddr + TX_STATUS); outb (0x5a, ioaddr + CONFIG_0); outb (0xe8, ioaddr + CONFIG_1); @@ -704,7 +780,7 @@ dev->name, inb(ioaddr + RX_MODE), status); #ifndef final_version if (status == 0) { - outb(0x05, ioaddr + 14); + outb(0x05, ioaddr + RX_CTRL); break; } #endif @@ -724,7 +800,7 @@ dev->name, pkt_len); /* Prime the FIFO and then flush the packet. */ inw(ioaddr + DATAPORT); inw(ioaddr + DATAPORT); - outb(0x05, ioaddr + 14); + outb(0x05, ioaddr + RX_CTRL); lp->stats.rx_errors++; break; } @@ -734,7 +810,7 @@ dev->name, pkt_len); /* Prime the FIFO and then flush the packet. */ inw(ioaddr + DATAPORT); inw(ioaddr + DATAPORT); - outb(0x05, ioaddr + 14); + outb(0x05, ioaddr + RX_CTRL); lp->stats.rx_dropped++; break; } @@ -761,7 +837,7 @@ if ((inb(ioaddr + RX_MODE) & 0x40) == 0x40) break; inw(ioaddr + DATAPORT); /* dummy status read */ - outb(0x05, ioaddr + 14); + outb(0x05, ioaddr + RX_CTRL); } if (net_debug > 5) @@ -851,7 +927,7 @@ /* Switch to bank 1 and set the multicast table. */ outw((saved_bank & ~0x0C00) | 0x0480, ioaddr + CONFIG_0); for (i = 0; i < 8; i++) - outb(mc_filter[i], ioaddr + 8 + i); + outb(mc_filter[i], ioaddr + PORT_OFFSET(8 + i)); memcpy(lp->mc_filter, mc_filter, sizeof(mc_filter)); outw(saved_bank, ioaddr + CONFIG_0); } @@ -861,7 +937,12 @@ #ifdef MODULE static struct net_device dev_at1700; +#ifndef CONFIG_X86_PC9800 static int io = 0x260; +#else +static int io = 0xd0; +#endif + static int irq; MODULE_PARM(io, "i"); @@ -901,7 +982,15 @@ /* If we don't do this, we can't re-insmod it later. */ free_irq(dev_at1700.irq, NULL); +#ifndef CONFIG_X86_PC9800 release_region(dev_at1700.base_addr, AT1700_IO_EXTENT); +#else + { + int i; + for (i = 0; i < 0x2000; i += 0x200) + release_region(dev_at1700.base_addr + i, 2); + } +#endif } #endif /* MODULE */ MODULE_LICENSE("GPL"); diff -Nru linux-2.5.61/drivers/net/ne.c linux98-2.5.61/drivers/net/ne.c --- linux-2.5.61/drivers/net/ne.c 2003-02-15 08:51:42.000000000 +0900 +++ linux98-2.5.61/drivers/net/ne.c 2003-02-16 11:49:42.000000000 +0900 @@ -109,6 +109,10 @@ {"PCM-4823", "PCM-4823", {0x00, 0xc0, 0x6c}}, /* Broken Advantech MoBo */ {"REALTEK", "RTL8019", {0x00, 0x00, 0xe8}}, /* no-name with Realtek chip */ {"LCS-8834", "LCS-8836", {0x04, 0x04, 0x37}}, /* ShinyNet (SET) */ + {"LA/T-98?", "LA/T-98", {0x00, 0xa0, 0xb0}}, /* I/O Data */ + {"EGY-98?", "EGY-98", {0x00, 0x40, 0x26}}, /* Melco EGY98 */ + {"ICM?", "ICM-27xx-ET", {0x00, 0x80, 0xc8}}, /* ICM IF-27xx-ET */ + {"CNET-98/EL?", "CNET(98)E/L", {0x00, 0x80, 0x4C}}, /* Contec CNET-98/EL */ {0,} }; #endif @@ -116,9 +120,10 @@ /* ---- No user-serviceable parts below ---- */ #define NE_BASE (dev->base_addr) -#define NE_CMD 0x00 -#define NE_DATAPORT 0x10 /* NatSemi-defined port window offset. */ -#define NE_RESET 0x1f /* Issue a read to reset, a write to clear. */ +#define NE_CMD EI_SHIFT(0x00) +#define NE_DATAPORT EI_SHIFT(0x10) /* NatSemi-defined port window offset. */ +#define NE_RESET EI_SHIFT(0x1f) /* Issue a read to reset, a write to clear. */ + #define NE_IO_EXTENT 0x20 #define NE1SM_START_PG 0x20 /* First page of TX buffer */ @@ -126,9 +131,15 @@ #define NESM_START_PG 0x40 /* First page of TX buffer */ #define NESM_STOP_PG 0x80 /* Last page +1 of RX ring */ +#ifdef CONFIG_NET_CBUS +#include "ne2k_cbus.h" +#endif + int ne_probe(struct net_device *dev); static int ne_probe1(struct net_device *dev, int ioaddr); +#ifndef CONFIG_NET_CBUS static int ne_probe_isapnp(struct net_device *dev); +#endif static int ne_open(struct net_device *dev); static int ne_close(struct net_device *dev); @@ -163,6 +174,8 @@ E2010 starts at 0x100 and ends at 0x4000. E2010-x starts at 0x100 and ends at 0xffff. */ +#ifndef CONFIG_NET_CBUS + int __init ne_probe(struct net_device *dev) { unsigned int base_addr = dev->base_addr; @@ -236,6 +249,116 @@ return -ENODEV; } +#else /* CONFIG_NET_CBUS */ + +int __init ne_probe(struct net_device *dev) +{ + unsigned int base_addr = dev->base_addr; + + SET_MODULE_OWNER(dev); + + if (ei_debug > 2) + printk(KERN_DEBUG "ne_probe(): entered.\n"); + + /* If CONFIG_NET_CBUS, + we need dev->priv->reg_offset BEFORE to probe */ + if (ne2k_cbus_init(dev) != 0) { + return -ENOMEM; + } + + /* First check any supplied i/o locations. User knows best. */ + if (base_addr > 0) { + int result; + const struct ne2k_cbus_hwinfo *hw = ne2k_cbus_get_hwinfo((int)(dev->mem_start & NE2K_CBUS_HARDWARE_TYPE_MASK)); + + if (ei_debug > 2) + printk(KERN_DEBUG "ne_probe(): call ne_probe_cbus(base_addr=0x%x)\n", base_addr); + + result = ne_probe_cbus(dev, hw, base_addr); + if (result != 0) + ne2k_cbus_destroy(dev); + + return result; + } + + if (ei_debug > 2) + printk(KERN_DEBUG "ne_probe(): base_addr is not specified.\n"); + +#ifndef MODULE + /* Last resort. The semi-risky C-Bus auto-probe. */ + if (ei_debug > 2) + printk(KERN_DEBUG "ne_probe(): auto-probe start.\n"); + + { + const struct ne2k_cbus_hwinfo *hw = ne2k_cbus_get_hwinfo((int)(dev->mem_start & NE2K_CBUS_HARDWARE_TYPE_MASK)); + + if (hw && hw->hwtype) { + const unsigned short *plist; + for (plist = hw->portlist; *plist; plist++) { + const struct ne2k_cbus_region *rlist; + for (rlist = hw->regionlist; rlist->range; rlist++) { + if (check_region(*plist+rlist->start, rlist->range)) + break; + } + if (rlist->range) { + /* check_region() failed */ + continue; /* try next base port */ + } + /* check_region() succeeded */ + if (ne_probe_cbus(dev,hw,*plist) == 0) + return 0; + } + } else { + for (hw = &ne2k_cbus_hwinfo_list[0]; hw->hwtype; hw++) { + const unsigned short *plist; + for(plist=hw->portlist; *plist; plist++){ + const struct ne2k_cbus_region *rlist; + + for (rlist = hw->regionlist; rlist->range; rlist++) { + if (check_region(*plist+rlist->start, rlist->range)) + break; + } + if (rlist->range) { + /* check_region() failed */ + continue; /* try next base port */ + } + /* check_region() succeeded */ + if (ne_probe_cbus(dev,hw,*plist) == 0) + return 0; + } + } + } + } +#endif + + ne2k_cbus_destroy(dev); + + return -ENODEV; +} + +static int __init ne_probe_cbus(struct net_device *dev, const struct ne2k_cbus_hwinfo *hw, int ioaddr) +{ + if (ei_debug > 2) + printk(KERN_DEBUG "ne_probe_cbus(): entered. (called from %p)\n", + __builtin_return_address(0)); + + if (hw && hw->hwtype) { + ne2k_cbus_set_hwtype(dev, hw, ioaddr); + return ne_probe1(dev, ioaddr); + } else { + /* auto detect */ + + printk(KERN_DEBUG "ne_probe_cbus(): try to determine hardware types.\n"); + for (hw = &ne2k_cbus_hwinfo_list[0]; hw->hwtype; hw++) { + ne2k_cbus_set_hwtype(dev, hw, ioaddr); + if (ne_probe1(dev, ioaddr)==0) + return 0; + } + } + return ENODEV; +} +#endif /* !CONFIG_NET_CBUS */ + static int __init ne_probe1(struct net_device *dev, int ioaddr) { int i; @@ -243,30 +366,62 @@ int wordlength = 2; const char *name = NULL; int start_page, stop_page; - int neX000, ctron, copam, bad_card; + int neX000, bad_card; +#ifndef CONFIG_NET_CBUS + int ctron, copam; +#endif int reg0, ret; static unsigned version_printed; +#ifdef CONFIG_NET_CBUS + const struct ne2k_cbus_hwinfo *hw = ne2k_cbus_get_hwinfo((int)(dev->mem_start & NE2K_CBUS_HARDWARE_TYPE_MASK)); + struct ei_device *ei_local = (struct ei_device *)(dev->priv); +#endif + +#ifdef CONFIG_NE2K_CBUS_CNET98EL + if (hw->hwtype == NE2K_CBUS_HARDWARE_TYPE_CNET98EL) { + outb_p(0, CONFIG_NE2K_CBUS_CNET98EL_IO_BASE); + /* udelay(5000); */ + outb_p(1, CONFIG_NE2K_CBUS_CNET98EL_IO_BASE); + /* udelay(5000); */ + outb_p((ioaddr & 0xf000) >> 8 | 0x08 | 0x01, CONFIG_NE2K_CBUS_CNET98EL_IO_BASE + 2); + /* udelay(5000); */ + } +#endif +#ifndef CONFIG_NET_CBUS if (!request_region(ioaddr, NE_IO_EXTENT, dev->name)) return -EBUSY; +#else /* CONFIG_NET_CBUS */ + { + const struct ne2k_cbus_region *rlist; + for (rlist = hw->regionlist; rlist->range; rlist++) { + if (!request_region(ioaddr + rlist->start, + rlist->range, dev->name)) + return -EBUSY; + } + } +#endif /* !CONFIG_NET_CBUS */ - reg0 = inb_p(ioaddr); + reg0 = inb_p(ioaddr + EI_SHIFT(0)); if (reg0 == 0xFF) { ret = -ENODEV; goto err_out; } /* Do a preliminary verification that we have a 8390. */ +#ifdef CONFIG_NE2K_CBUS_CNET98EL + if (hw->hwtype != NE2K_CBUS_HARDWARE_TYPE_CNET98EL) +#endif { int regd; outb_p(E8390_NODMA+E8390_PAGE1+E8390_STOP, ioaddr + E8390_CMD); - regd = inb_p(ioaddr + 0x0d); - outb_p(0xff, ioaddr + 0x0d); + regd = inb_p(ioaddr + EI_SHIFT(0x0d)); + outb_p(0xff, ioaddr + EI_SHIFT(0x0d)); outb_p(E8390_NODMA+E8390_PAGE0, ioaddr + E8390_CMD); inb_p(ioaddr + EN0_COUNTER0); /* Clear the counter by reading. */ if (inb_p(ioaddr + EN0_COUNTER0) != 0) { outb_p(reg0, ioaddr); - outb_p(regd, ioaddr + 0x0d); /* Restore the old values. */ + outb_p(regd, ioaddr + EI_SHIFT(0x0d)); /* Restore the old values. */ ret = -ENODEV; goto err_out; } @@ -290,6 +445,11 @@ { unsigned long reset_start_time = jiffies; +#ifdef CONFIG_NET_CBUS + /* derived from CNET98EL-patch for bad clones */ + outb_p(E8390_NODMA | E8390_STOP, ioaddr+E8390_CMD); +#endif + /* DON'T change these to inb_p/outb_p or reset will fail on clones. */ outb(inb(ioaddr + NE_RESET), ioaddr + NE_RESET); @@ -308,15 +468,86 @@ outb_p(0xff, ioaddr + EN0_ISR); /* Ack all intr. */ } +#ifdef CONFIG_NE2K_CBUS_CNET98EL + if (hw->hwtype == NE2K_CBUS_HARDWARE_TYPE_CNET98EL) { + static const char pat[32] ="AbcdeFghijKlmnoPqrstUvwxyZ789012"; + char buf[32]; + int maxwait = 200; + + if (ei_debug > 2) { + printk(" [CNET98EL-specific initialize..."); + } + outb_p(E8390_NODMA | E8390_STOP, ioaddr+E8390_CMD); /* 0x20|0x1 */ + i=inb(ioaddr); + if ((i & ~0x2) != (0x20 | 0x01)) + return ENODEV; + if ((inb(ioaddr + 0x7) & 0x80) != 0x80) + return ENODEV; + outb_p(E8390_RXOFF, ioaddr+EN0_RXCR); /* out(ioaddr+0xc, 0x20) */ + /* outb_p(ENDCFG_WTS|ENDCFG_FT1|ENDCFG_LS, ioaddr+EN0_DCFG); */ + outb_p(ENDCFG_WTS|0x48, ioaddr+EN0_DCFG); /* 0x49 */ + outb_p(CNET98EL_START_PG, ioaddr+EN0_STARTPG); + outb_p(CNET98EL_STOP_PG, ioaddr+EN0_STOPPG); + if (ei_debug > 2) { + printk("memory check"); + } + for (i = 0; i < 65536; i += 1024) { + if (ei_debug > 2) { + printk(" %04x",i); + } + ne2k_cbus_writemem(dev,ioaddr, i, pat, 32); + while (((inb(ioaddr + EN0_ISR) & ENISR_RDC) != ENISR_RDC) && --maxwait) + ; + ne2k_cbus_readmem(dev, ioaddr, i, buf, 32); + if (memcmp(pat, buf, 32)) { + if (ei_debug > 2) { + printk(" failed."); + } + break; + } + } + if (i != 16384) { + if (ei_debug > 2) { + printk("] "); + } + printk("memory failure at %x\n", i); + return ENODEV; + } + if (ei_debug > 2) { + printk(" good..."); + } + if (!dev->irq) { + if (ei_debug > 2) { + printk("] "); + } + printk("IRQ must be specified for C-NET(98)E/L. probe failed.\n"); + return ENODEV; + } + outb((dev->irq>5) ? (dev->irq&4):(dev->irq>>1), ioaddr + (0x2 | 0x400)); + outb(0x7e, ioaddr + (0x4 | 0x400)); + ne2k_cbus_readmem(dev, ioaddr, 16384, SA_prom, 32); + outb(0xff, ioaddr + EN0_ISR); + if (ei_debug > 2) { + printk("done]"); + } + } else +#endif /* CONFIG_NE2K_CBUS_CNET98EL */ /* Read the 16 bytes of station address PROM. We must first initialize registers, similar to NS8390_init(eifdev, 0). We can't reliably read the SAPROM address without this. (I learned the hard way!). */ { - struct {unsigned char value, offset; } program_seq[] = + struct {unsigned char value; unsigned short offset;} program_seq[] = { {E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/ +#ifndef CONFIG_NET_CBUS {0x48, EN0_DCFG}, /* Set byte-wide (0x48) access. */ +#else + /* NEC PC-9800: some board can only handle word-wide access? */ + {0x48 | ENDCFG_WTS, EN0_DCFG}, /* Set word-wide (0x48) access. */ + {16384 / 256, EN0_STARTPG}, + {32768 / 256, EN0_STOPPG}, +#endif {0x00, EN0_RCNTLO}, /* Clear the count regs. */ {0x00, EN0_RCNTHI}, {0x00, EN0_IMR}, /* Mask completion irq. */ @@ -332,29 +563,42 @@ for (i = 0; i < sizeof(program_seq)/sizeof(program_seq[0]); i++) outb_p(program_seq[i].value, ioaddr + program_seq[i].offset); - - } +#ifndef CONFIG_NET_CBUS for(i = 0; i < 32 /*sizeof(SA_prom)*/; i+=2) { SA_prom[i] = inb(ioaddr + NE_DATAPORT); SA_prom[i+1] = inb(ioaddr + NE_DATAPORT); if (SA_prom[i] != SA_prom[i+1]) wordlength = 1; } +#else + insw(ioaddr + NE_DATAPORT, SA_prom, 32 >> 1); +#endif + + } if (wordlength == 2) { for (i = 0; i < 16; i++) SA_prom[i] = SA_prom[i+i]; +#ifndef CONFIG_NET_CBUS /* We must set the 8390 for word mode. */ outb_p(0x49, ioaddr + EN0_DCFG); +#endif start_page = NESM_START_PG; stop_page = NESM_STOP_PG; +#ifdef CONFIG_NE2K_CBUS_CNET98EL + if (hw->hwtype == NE2K_CBUS_HARDWARE_TYPE_CNET98EL) { + start_page = CNET98EL_START_PG; + stop_page = CNET98EL_STOP_PG; + } +#endif } else { start_page = NE1SM_START_PG; stop_page = NE1SM_STOP_PG; } neX000 = (SA_prom[14] == 0x57 && SA_prom[15] == 0x57); +#ifndef CONFIG_NET_CBUS ctron = (SA_prom[0] == 0x00 && SA_prom[1] == 0x00 && SA_prom[2] == 0x1d); copam = (SA_prom[14] == 0x49 && SA_prom[15] == 0x00); @@ -368,6 +612,11 @@ start_page = 0x01; stop_page = (wordlength == 2) ? 0x40 : 0x20; } +#else + if (neX000) { + name = "C-Bus-NE2K-compat"; + } +#endif else { #ifdef SUPPORT_NE_BAD_CLONES @@ -414,10 +663,18 @@ dev->irq = probe_irq_off(cookie); if (ei_debug > 2) printk(" autoirq is %d\n", dev->irq); - } else if (dev->irq == 2) + } else +#ifndef CONFIG_X86_PC9800 + if (dev->irq == 2) /* Fixup for users that don't know that IRQ 2 is really IRQ 9, or don't know which one to set. */ dev->irq = 9; +#else + if (dev->irq == 7) + /* Fixup for users that don't know that IRQ 7 is really IRQ 11, + or don't know which one to set. */ + dev->irq = 11; +#endif if (! dev->irq) { printk(" failed to detect IRQ line.\n"); @@ -448,8 +705,13 @@ dev->dev_addr[i] = SA_prom[i]; } +#ifndef CONFIG_NET_CBUS printk("\n%s: %s found at %#x, using IRQ %d.\n", dev->name, name, ioaddr, dev->irq); +#else + printk("\n%s: %s found at %#x, hardware type %d(%s), using IRQ %d.\n", + dev->name, name, ioaddr, hw->hwtype, hw->hwident, dev->irq); +#endif ei_status.name = name; ei_status.tx_start_page = start_page; @@ -473,10 +735,23 @@ return 0; err_out_kfree: +#ifndef CONFIG_NET_CBUS kfree(dev->priv); dev->priv = NULL; +#else + ne2k_cbus_destroy(dev); +#endif err_out: +#ifndef CONFIG_NET_CBUS release_region(ioaddr, NE_IO_EXTENT); +#else + { + const struct ne2k_cbus_region *rlist; + for (rlist = hw->regionlist; rlist->range; rlist++) { + release_region(ioaddr + rlist->start, rlist->range); + } + } +#endif return ret; } @@ -500,10 +775,18 @@ static void ne_reset_8390(struct net_device *dev) { unsigned long reset_start_time = jiffies; +#ifdef CONFIG_NET_CBUS + struct ei_device *ei_local = (struct ei_device *)(dev->priv); +#endif if (ei_debug > 1) printk(KERN_DEBUG "resetting the 8390 t=%ld...", jiffies); +#ifdef CONFIG_NET_CBUS + /* derived from CNET98EL-patch for bad clones... */ + outb_p(E8390_NODMA | E8390_STOP, NE_BASE + E8390_CMD); /* 0x20 | 0x1 */ +#endif + /* DON'T change these to inb_p/outb_p or reset will fail on clones. */ outb(inb(NE_BASE + NE_RESET), NE_BASE + NE_RESET); @@ -526,6 +809,9 @@ static void ne_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page) { int nic_base = dev->base_addr; +#ifdef CONFIG_NET_CBUS + struct ei_device *ei_local = (struct ei_device *)(dev->priv); +#endif /* This *shouldn't* happen. If it does, it's the last thing you'll see */ @@ -568,6 +854,9 @@ #endif int nic_base = dev->base_addr; char *buf = skb->data; +#ifdef CONFIG_NET_CBUS + struct ei_device *ei_local = (struct ei_device *)(dev->priv); +#endif /* This *shouldn't* happen. If it does, it's the last thing you'll see */ if (ei_status.dmaing) @@ -578,6 +867,12 @@ return; } ei_status.dmaing |= 0x01; + +#ifdef CONFIG_NET_CBUS + /* round up count to a word (derived from ICM-patch) */ + count = (count + 1) & ~1; +#endif + outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, nic_base+ NE_CMD); outb_p(count & 0xff, nic_base + EN0_RCNTLO); outb_p(count >> 8, nic_base + EN0_RCNTHI); @@ -635,6 +930,9 @@ #ifdef NE_SANITY_CHECK int retries = 0; #endif +#ifdef CONFIG_NET_CBUS + struct ei_device *ei_local = (struct ei_device *)(dev->priv); +#endif /* Round the count up for word writes. Do we need to do this? What effect will an odd byte count have on the 8390? @@ -738,13 +1036,22 @@ static int io[MAX_NE_CARDS]; static int irq[MAX_NE_CARDS]; static int bad[MAX_NE_CARDS]; /* 0xbad = bad sig or no reset ack */ +#ifdef CONFIG_NET_CBUS +static int hwtype[MAX_NE_CARDS] = { 0, }; /* board type */ +#endif MODULE_PARM(io, "1-" __MODULE_STRING(MAX_NE_CARDS) "i"); MODULE_PARM(irq, "1-" __MODULE_STRING(MAX_NE_CARDS) "i"); MODULE_PARM(bad, "1-" __MODULE_STRING(MAX_NE_CARDS) "i"); +#ifdef CONFIG_NET_CBUS +MODULE_PARM(hwtype, "1-" __MODULE_STRING(MAX_NE_CARDS) "i"); +#endif MODULE_PARM_DESC(io, "I/O base address(es),required"); MODULE_PARM_DESC(irq, "IRQ number(s)"); MODULE_PARM_DESC(bad, "Accept card(s) with bad signatures"); +#ifdef CONFIG_NET_CBUS +MODULE_PARM_DESC(hwtype, "Board type of PC-9800 C-Bus NIC"); +#endif MODULE_DESCRIPTION("NE1000/NE2000 ISA/PnP Ethernet driver"); MODULE_LICENSE("GPL"); @@ -762,6 +1069,9 @@ dev->irq = irq[this_dev]; dev->mem_end = bad[this_dev]; dev->base_addr = io[this_dev]; +#ifdef CONFIG_NET_CBUS + dev->mem_start = hwtype[this_dev]; +#endif dev->init = ne_probe; if (register_netdev(dev) == 0) { found++; @@ -791,9 +1101,23 @@ if (idev) pnp_device_detach(idev); free_irq(dev->irq, dev); +#ifndef CONFIG_NET_CBUS release_region(dev->base_addr, NE_IO_EXTENT); +#else /* CONFIG_NET_CBUS */ + { + const struct ne2k_cbus_hwinfo *hw = ne2k_cbus_get_hwinfo((int)(dev->mem_start & NE2K_CBUS_HARDWARE_TYPE_MASK)); + const struct ne2k_cbus_region *rlist; + for (rlist = hw->regionlist; rlist->range; rlist++) { + release_region(dev->base_addr + rlist->start, rlist->range); + } + } +#endif /* !CONFIG_NET_CBUS */ unregister_netdev(dev); +#ifndef CONFIG_NET_CBUS kfree(priv); +#else + ne2k_cbus_destroy(dev); +#endif } } } diff -Nru linux-2.5.50/drivers/net/ne2k_cbus.h linux98-2.5.50/drivers/net/ne2k_cbus.h --- linux-2.5.42/drivers/net/ne2k_cbus.h 1970-01-01 09:00:00.000000000 +0900 +++ linux98-2.5.42/drivers/net/ne2k_cbus.h 2002-12-15 10:56:15.000000000 +0900 @@ -0,0 +1,481 @@ +/* ne2k_cbus.h: + vender-specific information definition for NEC PC-9800 + C-bus Ethernet Cards + Used in ne.c + + (C)1998,1999 KITAGWA Takurou & Linux/98 project +*/ + +#include + +#undef NE_RESET +#define NE_RESET EI_SHIFT(0x11) /* Issue a read to reset, a write to clear. */ + +#ifdef CONFIG_NE2K_CBUS_CNET98EL +#ifndef CONFIG_NE2K_CBUS_CNET98EL_IO_BASE +#warning CONFIG_NE2K_CBUS_CNET98EL_IO_BASE is not defined(config error?) +#warning use 0xaaed as default +#define CONFIG_NE2K_CBUS_CNET98EL_IO_BASE 0xaaed /* or 0x55ed */ +#endif +#define CNET98EL_START_PG 0x00 +#define CNET98EL_STOP_PG 0x40 +#endif + +/* Hardware type definition (derived from *BSD) */ +#define NE2K_CBUS_HARDWARE_TYPE_MASK 0xff + +/* 0: reserved for auto-detect */ +/* 1: (not tested) + Allied Telesis CentreCom LA-98-T */ +#define NE2K_CBUS_HARDWARE_TYPE_ATLA98 1 +/* 2: (not tested) + ELECOM Laneed + LD-BDN[123]A + PLANET SMART COM 98 EN-2298-C + MACNICA ME98 */ +#define NE2K_CBUS_HARDWARE_TYPE_BDN 2 +/* 3: + Melco EGY-98 + Contec C-NET(98)E*A/L*A,C-NET(98)P */ +#define NE2K_CBUS_HARDWARE_TYPE_EGY98 3 +/* 4: + Melco LGY-98,IND-SP,IND-SS + MACNICA NE2098 */ +#define NE2K_CBUS_HARDWARE_TYPE_LGY98 4 +/* 5: + ICM DT-ET-25,DT-ET-T5,IF-2766ET,IF-2771ET + PLANET SMART COM 98 EN-2298-T,EN-2298P-T + D-Link DE-298PT,DE-298PCAT + ELECOM Laneed LD-98P */ +#define NE2K_CBUS_HARDWARE_TYPE_ICM 5 +/* 6: (reserved for SIC-98, which is not supported in this driver.) */ +/* 7: (unused in *BSD?) + + +*/ +#define NE2K_CBUS_HARDWARE_TYPE_NE2K 7 +/* 8: + NEC PC-9801-108 */ +#define NE2K_CBUS_HARDWARE_TYPE_NEC108 8 +/* 9: + I-O DATA LA-98,LA/T-98 */ +#define NE2K_CBUS_HARDWARE_TYPE_IOLA98 9 +/* 10: (reserved for C-NET(98), which is not supported in this driver.) */ +/* 11: + Contec C-NET(98)E,L */ +#define NE2K_CBUS_HARDWARE_TYPE_CNET98EL 11 + +#define NE2K_CBUS_HARDWARE_TYPE_MAX 11 + +/* HARDWARE TYPE ID 12-31: reserved */ + +struct ne2k_cbus_offsetinfo { + unsigned short skip; + unsigned short offset8; /* +0x8 - +0xf */ + unsigned short offset10; /* +0x10 */ + unsigned short offset1f; /* +0x1f */ +}; + +struct ne2k_cbus_region { + unsigned short start; + short range; +}; + +struct ne2k_cbus_hwinfo { + const unsigned short hwtype; + const unsigned char *hwident; +#ifndef MODULE + const unsigned short *portlist; +#endif + const struct ne2k_cbus_offsetinfo *offsetinfo; + const struct ne2k_cbus_region *regionlist; +}; + +#ifdef CONFIG_NE2K_CBUS_ATLA98 +#ifndef MODULE +static unsigned short atla98_portlist[] __initdata = { + 0xd0, + 0 +}; +#endif +#define atla98_offsetinfo ne2k_offsetinfo +#define atla98_regionlist ne2k_regionlist +#endif /* CONFIG_NE2K_CBUS_ATLA98 */ + +#ifdef CONFIG_NE2K_CBUS_BDN +#ifndef MODULE +static unsigned short bdn_portlist[] __initdata = { + 0xd0, + 0 +}; +#endif +static struct ne2k_cbus_offsetinfo bdn_offsetinfo __initdata = { +#if 0 + /* comes from FreeBSD(98) ed98.h */ + 0x1000, 0x8000, 0x100, 0xc200 /* ??? */ +#else + /* comes from NetBSD/pc98 if_ne_isa.c */ + 0x1000, 0x8000, 0x100, 0x7f00 /* ??? */ +#endif +}; +static struct ne2k_cbus_region bdn_regionlist[] __initdata = { + {0x0, 1}, {0x1000, 1}, {0x2000, 1}, {0x3000,1}, + {0x4000, 1}, {0x5000, 1}, {0x6000, 1}, {0x7000, 1}, + {0x8000, 1}, {0x9000, 1}, {0xa000, 1}, {0xb000, 1}, + {0xc000, 1}, {0xd000, 1}, {0xe000, 1}, {0xf000, 1}, + {0x100, 1}, {0x7f00, 1}, + {0x0, 0} +}; +#endif /* CONFIG_NE2K_CBUS_BDN */ + +#ifdef CONFIG_NE2K_CBUS_EGY98 +#ifndef MODULE +static unsigned short egy98_portlist[] __initdata = { + 0xd0, + 0 +}; +#endif +static struct ne2k_cbus_offsetinfo egy98_offsetinfo __initdata = { + 0x02, 0x100, 0x200, 0x300 +}; +static struct ne2k_cbus_region egy98_regionlist[] __initdata = { + {0x0, 1}, {0x2, 1}, {0x4, 1}, {0x6, 1}, + {0x8, 1}, {0xa, 1}, {0xc, 1}, {0xe, 1}, + {0x100, 1}, {0x102, 1}, {0x104, 1}, {0x106, 1}, + {0x108, 1}, {0x10a, 1}, {0x10c, 1}, {0x10e, 1}, + {0x200, 1}, {0x300, 1}, + {0x0, 0} +}; +#endif /* CONFIG_NE2K_CBUS_EGY98 */ + +#ifdef CONFIG_NE2K_CBUS_LGY98 +#ifndef MODULE +static unsigned short lgy98_portlist[] __initdata = { + 0xd0, 0x10d0, 0x20d0, 0x30d0, 0x40d0, 0x50d0, 0x60d0, 0x70d0, + 0 +}; +#endif +static struct ne2k_cbus_offsetinfo lgy98_offsetinfo __initdata = { + 0x01, 0x08, 0x200, 0x300 +}; +static struct ne2k_cbus_region lgy98_regionlist[] __initdata = { + {0x0, 16}, {0x200, 1}, {0x300, 1}, + {0x0, 0} +}; +#endif /* CONFIG_NE2K_CBUS_LGY98 */ + +#ifdef CONFIG_NE2K_CBUS_ICM +#ifndef MODULE +static unsigned short icm_portlist[] __initdata = { + /* ICM */ + 0x56d0, + /* LD-98PT */ + 0x46d0, 0x66d0, 0x76d0, 0x86d0, 0x96d0, 0xa6d0, 0xb6d0, 0xc6d0, + 0 +}; +#endif +static struct ne2k_cbus_offsetinfo icm_offsetinfo __initdata = { + 0x01, 0x08, 0x100, 0x10f +}; +static struct ne2k_cbus_region icm_regionlist[] __initdata = { + {0x0, 16}, {0x100, 16}, + {0x0, 0} +}; +#endif /* CONFIG_NE2K_CBUS_ICM */ + +#if defined(CONFIG_NE2K_CBUS_NE2K) && !defined(MODULE) +static unsigned short ne2k_portlist[] __initdata = { + 0xd0, 0x300, 0x280, 0x320, 0x340, 0x360, 0x380, + 0 +}; +#endif +#if defined(CONFIG_NE2K_CBUS_NE2K) || defined(CONFIG_NE2K_CBUS_ATLA98) +static struct ne2k_cbus_offsetinfo ne2k_offsetinfo __initdata = { + 0x01, 0x08, 0x10, 0x1f +}; +static struct ne2k_cbus_region ne2k_regionlist[] __initdata = { + {0x0, 32}, + {0x0, 0} +}; +#endif + +#ifdef CONFIG_NE2K_CBUS_NEC108 +#ifndef MODULE +static unsigned short nec108_portlist[] __initdata = { + 0x770, 0x2770, 0x4770, 0x6770, + 0 +}; +#endif +static struct ne2k_cbus_offsetinfo nec108_offsetinfo __initdata = { + 0x02, 0x1000, 0x888, 0x88a +}; +static struct ne2k_cbus_region nec108_regionlist[] __initdata = { + {0x0, 1}, {0x2, 1}, {0x4, 1}, {0x6, 1}, + {0x8, 1}, {0xa, 1}, {0xc, 1}, {0xe, 1}, + {0x1000, 1}, {0x1002, 1}, {0x1004, 1}, {0x1006, 1}, + {0x1008, 1}, {0x100a, 1}, {0x100c, 1}, {0x100e, 1}, + {0x888, 1}, {0x88a, 1}, {0x88c, 1}, {0x88e, 1}, + {0x0, 0} +}; +#endif + +#ifdef CONFIG_NE2K_CBUS_IOLA98 +#ifndef MODULE +static unsigned short iola98_portlist[] __initdata = { + 0xd0, 0xd2, 0xd4, 0xd6, 0xd8, 0xda, 0xdc, 0xde, + 0 +}; +#endif +static struct ne2k_cbus_offsetinfo iola98_offsetinfo __initdata = { + 0x1000, 0x8000, 0x100, 0xf100 +}; +static struct ne2k_cbus_region iola98_regionlist[] __initdata = { + {0x0, 1}, {0x1000, 1}, {0x2000, 1}, {0x3000, 1}, + {0x4000, 1}, {0x5000, 1}, {0x6000, 1}, {0x7000, 1}, + {0x8000, 1}, {0x9000, 1}, {0xa000, 1}, {0xb000, 1}, + {0xc000, 1}, {0xd000, 1}, {0xe000, 1}, {0xf000, 1}, + {0x100, 1}, {0xf100, 1}, + {0x0,0} +}; +#endif /* CONFIG_NE2K_CBUS_IOLA98 */ + +#ifdef CONFIG_NE2K_CBUS_CNET98EL +#ifndef MODULE +static unsigned short cnet98el_portlist[] __initdata = { + 0x3d0, 0x13d0, 0x23d0, 0x33d0, 0x43d0, 0x53d0, 0x60d0, 0x70d0, + 0 +}; +#endif +static struct ne2k_cbus_offsetinfo cnet98el_offsetinfo __initdata = { + 0x01, 0x08, 0x40e, 0x400 +}; +static struct ne2k_cbus_region cnet98el_regionlist[] __initdata = { + {0x0, 16}, {0x400, 16}, + {0x0, 0} +}; +#endif + + +/* port information table (for ne.c initialize/probe process) */ + +static struct ne2k_cbus_hwinfo ne2k_cbus_hwinfo_list[] __initdata = { +#ifdef CONFIG_NE2K_CBUS_ATLA98 +/* NOT TESTED */ + { + NE2K_CBUS_HARDWARE_TYPE_ATLA98, + "LA-98-T", +#ifndef MODULE + atla98_portlist, +#endif + &atla98_offsetinfo, atla98_regionlist + }, +#endif +#ifdef CONFIG_NE2K_CBUS_BDN +/* NOT TESTED */ + { + NE2K_CBUS_HARDWARE_TYPE_BDN, + "LD-BDN[123]A", +#ifndef MODULE + bdn_portlist, +#endif + &bdn_offsetinfo, bdn_regionlist + }, +#endif +#ifdef CONFIG_NE2K_CBUS_ICM + { + NE2K_CBUS_HARDWARE_TYPE_ICM, + "IF-27xxET", +#ifndef MODULE + icm_portlist, +#endif + &icm_offsetinfo, icm_regionlist + }, +#endif +#ifdef CONFIG_NE2K_CBUS_NE2K + { + NE2K_CBUS_HARDWARE_TYPE_NE2K, + "NE2000 compat.", +#ifndef MODULE + ne2k_portlist, +#endif + &ne2k_offsetinfo, ne2k_regionlist + }, +#endif +#ifdef CONFIG_NE2K_CBUS_NEC108 + { + NE2K_CBUS_HARDWARE_TYPE_NEC108, + "PC-9801-108", +#ifndef MODULE + nec108_portlist, +#endif + &nec108_offsetinfo, nec108_regionlist + }, +#endif +#ifdef CONFIG_NE2K_CBUS_IOLA98 + { + NE2K_CBUS_HARDWARE_TYPE_IOLA98, + "LA-98", +#ifndef MODULE + iola98_portlist, +#endif + &iola98_offsetinfo, iola98_regionlist + }, +#endif +#ifdef CONFIG_NE2K_CBUS_CNET98EL + { + NE2K_CBUS_HARDWARE_TYPE_CNET98EL, + "C-NET(98)E/L", +#ifndef MODULE + cnet98el_portlist, +#endif + &cnet98el_offsetinfo, cnet98el_regionlist + }, +#endif +/* NOTE: LGY98 must be probed before EGY98, or system stalled!? */ +#ifdef CONFIG_NE2K_CBUS_LGY98 + { + NE2K_CBUS_HARDWARE_TYPE_LGY98, + "LGY-98", +#ifndef MODULE + lgy98_portlist, +#endif + &lgy98_offsetinfo, lgy98_regionlist + }, +#endif +#ifdef CONFIG_NE2K_CBUS_EGY98 + { + NE2K_CBUS_HARDWARE_TYPE_EGY98, + "EGY-98", +#ifndef MODULE + egy98_portlist, +#endif + &egy98_offsetinfo, egy98_regionlist + }, +#endif + { + 0, + "unsupported hardware", +#ifndef MODULE + NULL, +#endif + NULL, NULL + } +}; + +static int __init ne2k_cbus_init(struct net_device *dev) +{ + struct ei_device *ei_local; + if (dev->priv == NULL) { + ei_local = kmalloc(sizeof(struct ei_device), GFP_KERNEL); + if (ei_local == NULL) + return -ENOMEM; + memset(ei_local, 0, sizeof(struct ei_device)); + ei_local->reg_offset = kmalloc(sizeof(typeof(*ei_local->reg_offset))*18, GFP_KERNEL); + if (ei_local->reg_offset == NULL) { + kfree(ei_local); + return -ENOMEM; + } + spin_lock_init(&ei_local->page_lock); + dev->priv = ei_local; + } + return 0; +} + +static void ne2k_cbus_destroy(struct net_device *dev) +{ + struct ei_device *ei_local = (struct ei_device *)(dev->priv); + if (ei_local != NULL) { + if (ei_local->reg_offset) + kfree(ei_local->reg_offset); + kfree(dev->priv); + dev->priv = NULL; + } +} + +static const struct ne2k_cbus_hwinfo * __init ne2k_cbus_get_hwinfo(int hwtype) +{ + const struct ne2k_cbus_hwinfo *hw; + + for (hw = &ne2k_cbus_hwinfo_list[0]; hw->hwtype; hw++) { + if (hw->hwtype == hwtype) break; + } + return hw; +} + +static void __init ne2k_cbus_set_hwtype(struct net_device *dev, const struct ne2k_cbus_hwinfo *hw, int ioaddr) +{ + struct ei_device *ei_local = (struct ei_device *)(dev->priv); + int i; + int hwtype_old = dev->mem_start & NE2K_CBUS_HARDWARE_TYPE_MASK; + + if (!ei_local) + panic("Gieee! ei_local == NULL!! (from %p)", + __builtin_return_address(0)); + + dev->mem_start &= ~NE2K_CBUS_HARDWARE_TYPE_MASK; + dev->mem_start |= hw->hwtype & NE2K_CBUS_HARDWARE_TYPE_MASK; + + if (ei_debug > 2) { + printk(KERN_DEBUG "hwtype changed: %d -> %d\n",hwtype_old,(int)(dev->mem_start & NE2K_CBUS_HARDWARE_TYPE_MASK)); + } + + if (hw->offsetinfo) { + for (i = 0; i < 8; i++) { + ei_local->reg_offset[i] = hw->offsetinfo->skip * i; + } + for (i = 8; i < 16; i++) { + ei_local->reg_offset[i] = + hw->offsetinfo->skip*(i-8) + hw->offsetinfo->offset8; + } +#ifdef CONFIG_NE2K_CBUS_NEC108 + if (hw->hwtype == NE2K_CBUS_HARDWARE_TYPE_NEC108) { + int adj = (ioaddr & 0xf000) /2; + ei_local->reg_offset[16] = + (hw->offsetinfo->offset10 | adj) - ioaddr; + ei_local->reg_offset[17] = + (hw->offsetinfo->offset1f | adj) - ioaddr; + } else { +#endif /* CONFIG_NE2K_CBUS_NEC108 */ + ei_local->reg_offset[16] = hw->offsetinfo->offset10; + ei_local->reg_offset[17] = hw->offsetinfo->offset1f; +#ifdef CONFIG_NE2K_CBUS_NEC108 + } +#endif + } else { + /* make dummmy offset list */ + for (i = 0; i < 16; i++) { + ei_local->reg_offset[i] = i; + } + ei_local->reg_offset[16] = 0x10; + ei_local->reg_offset[17] = 0x1f; + } +} + +#if defined(CONFIG_NE2K_CBUS_ICM) || defined(CONFIG_NE2K_CBUS_CNET98EL) +static void __init ne2k_cbus_readmem(struct net_device *dev, int ioaddr, unsigned short memaddr, char *buf, unsigned short len) +{ + struct ei_device *ei_local = (struct ei_device *)(dev->priv); + outb_p(E8390_NODMA | E8390_START, ioaddr+E8390_CMD); + outb_p(len & 0xff, ioaddr+EN0_RCNTLO); + outb_p(len >> 8, ioaddr+EN0_RCNTHI); + outb_p(memaddr & 0xff, ioaddr+EN0_RSARLO); + outb_p(memaddr >> 8, ioaddr+EN0_RSARHI); + outb_p(E8390_RREAD | E8390_START, ioaddr+E8390_CMD); + insw(ioaddr+NE_DATAPORT, buf, len >> 1); +} +static void __init ne2k_cbus_writemem(struct net_device *dev, int ioaddr, unsigned short memaddr, const char *buf, unsigned short len) +{ + struct ei_device *ei_local = (struct ei_device *)(dev->priv); + outb_p(E8390_NODMA | E8390_START, ioaddr+E8390_CMD); + outb_p(ENISR_RDC, ioaddr+EN0_ISR); + outb_p(len & 0xff, ioaddr+EN0_RCNTLO); + outb_p(len >> 8, ioaddr+EN0_RCNTHI); + outb_p(memaddr & 0xff, ioaddr+EN0_RSARLO); + outb_p(memaddr >> 8, ioaddr+EN0_RSARHI); + outb_p(E8390_RWRITE | E8390_START, ioaddr+E8390_CMD); + outsw(ioaddr+NE_DATAPORT, buf, len >> 1); +} +#endif + +static int ne_probe_cbus(struct net_device *dev, const struct ne2k_cbus_hwinfo *hw, int ioaddr); +/* End of ne2k_cbus.h */ - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/