Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1751794AbbHRH4J (ORCPT ); Tue, 18 Aug 2015 03:56:09 -0400 Received: from mail-pa0-f43.google.com ([209.85.220.43]:32994 "EHLO mail-pa0-f43.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751083AbbHRH4H (ORCPT ); Tue, 18 Aug 2015 03:56:07 -0400 From: Tomer Barletz To: linux-usb@vger.kernel.org Cc: mathias.nyman@intel.com, gregkh@linuxfoundation.org, linux-kernel@vger.kernel.org, Tomer Barletz Subject: [PATCH] usb: Move xhci_pme_quirk() behind an #ifdef CONFIG_PM, as it is not used when it's not defined Date: Tue, 18 Aug 2015 00:55:37 -0700 Message-Id: <1439884537-8615-1-git-send-email-barletz@gmail.com> X-Mailer: git-send-email 2.4.3 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 3892 Lines: 121 Signed-off-by: Tomer Barletz --- drivers/usb/host/xhci-pci.c | 90 ++++++++++++++++++++++----------------------- 1 file changed, 45 insertions(+), 45 deletions(-) diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index 5590eac..c79d336 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -180,51 +180,6 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci) "QUIRK: Resetting on resume"); } -/* - * In some Intel xHCI controllers, in order to get D3 working, - * through a vendor specific SSIC CONFIG register at offset 0x883c, - * SSIC PORT need to be marked as "unused" before putting xHCI - * into D3. After D3 exit, the SSIC port need to be marked as "used". - * Without this change, xHCI might not enter D3 state. - * Make sure PME works on some Intel xHCI controllers by writing 1 to clear - * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4 - */ -static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend) -{ - struct xhci_hcd *xhci = hcd_to_xhci(hcd); - struct pci_dev *pdev = to_pci_dev(hcd->self.controller); - u32 val; - void __iomem *reg; - - if (pdev->vendor == PCI_VENDOR_ID_INTEL && - pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) { - - reg = (void __iomem *) xhci->cap_regs + PORT2_SSIC_CONFIG_REG2; - - /* Notify SSIC that SSIC profile programming is not done */ - val = readl(reg) & ~PROG_DONE; - writel(val, reg); - - /* Mark SSIC port as unused(suspend) or used(resume) */ - val = readl(reg); - if (suspend) - val |= SSIC_PORT_UNUSED; - else - val &= ~SSIC_PORT_UNUSED; - writel(val, reg); - - /* Notify SSIC that SSIC profile programming is done */ - val = readl(reg) | PROG_DONE; - writel(val, reg); - readl(reg); - } - - reg = (void __iomem *) xhci->cap_regs + 0x80a4; - val = readl(reg); - writel(val | BIT(28), reg); - readl(reg); -} - #ifdef CONFIG_ACPI static void xhci_pme_acpi_rtd3_enable(struct pci_dev *dev) { @@ -345,6 +300,51 @@ static void xhci_pci_remove(struct pci_dev *dev) } #ifdef CONFIG_PM +/* + * In some Intel xHCI controllers, in order to get D3 working, + * through a vendor specific SSIC CONFIG register at offset 0x883c, + * SSIC PORT need to be marked as "unused" before putting xHCI + * into D3. After D3 exit, the SSIC port need to be marked as "used". + * Without this change, xHCI might not enter D3 state. + * Make sure PME works on some Intel xHCI controllers by writing 1 to clear + * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4 + */ +static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend) +{ + struct xhci_hcd *xhci = hcd_to_xhci(hcd); + struct pci_dev *pdev = to_pci_dev(hcd->self.controller); + u32 val; + void __iomem *reg; + + if (pdev->vendor == PCI_VENDOR_ID_INTEL && + pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) { + + reg = (void __iomem *) xhci->cap_regs + PORT2_SSIC_CONFIG_REG2; + + /* Notify SSIC that SSIC profile programming is not done */ + val = readl(reg) & ~PROG_DONE; + writel(val, reg); + + /* Mark SSIC port as unused(suspend) or used(resume) */ + val = readl(reg); + if (suspend) + val |= SSIC_PORT_UNUSED; + else + val &= ~SSIC_PORT_UNUSED; + writel(val, reg); + + /* Notify SSIC that SSIC profile programming is done */ + val = readl(reg) | PROG_DONE; + writel(val, reg); + readl(reg); + } + + reg = (void __iomem *) xhci->cap_regs + 0x80a4; + val = readl(reg); + writel(val | BIT(28), reg); + readl(reg); +} + static int xhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup) { struct xhci_hcd *xhci = hcd_to_xhci(hcd); -- 2.4.3 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/