Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S932084AbbKBF0i (ORCPT ); Mon, 2 Nov 2015 00:26:38 -0500 Received: from arroyo.ext.ti.com ([192.94.94.40]:44556 "EHLO arroyo.ext.ti.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752931AbbKBF0e (ORCPT ); Mon, 2 Nov 2015 00:26:34 -0500 From: Milo Kim To: , , CC: Milo Kim , Guenter Roeck , Jean Delvare , Subject: [PATCH RESEND 14/16] hwmon: add TI LMU hardware fault monitoring driver Date: Mon, 2 Nov 2015 14:24:33 +0900 Message-ID: <1446441875-1256-15-git-send-email-milo.kim@ti.com> X-Mailer: git-send-email 1.9.5.msysgit.0 In-Reply-To: <1446441875-1256-1-git-send-email-milo.kim@ti.com> References: <1446441875-1256-1-git-send-email-milo.kim@ti.com> MIME-Version: 1.0 Content-Type: text/plain Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 13300 Lines: 481 LM3633 and LM3697 are TI LMU MFD device. Those device have hardware monitoring feature which detects opened or shorted circuit case. Attributes ---------- Two attributes are registered. open_fault: check backlight output channel is opened or not short_fault: check backlight output channel is shorted or not With register R/W operations, LMU HWMON driver checks the status of backlight output channels. LM3633 and LM3697 have same sequence to check channels, so common functions are used. Operations ---------- Two devices have common control flow but register addresses are different. The structure, 'ti_lmu_reg' is used for device configuration. HWMON notifier -------------- After LMU HWMON operation is done, backlight device should be reinitialized. LMU HWMON driver notifies an event as soon as the monitoring is done. Then, LM3633 and LM3697 backlight driver handles this event. Cc: Guenter Roeck Cc: Jean Delvare Cc: Lee Jones Cc: devicetree@vger.kernel.org Cc: lm-sensors@lm-sensors.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Milo Kim --- drivers/hwmon/Kconfig | 10 ++ drivers/hwmon/Makefile | 1 + drivers/hwmon/ti-lmu-hwmon.c | 393 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 404 insertions(+) create mode 100644 drivers/hwmon/ti-lmu-hwmon.c diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index e13c902..989e1fa 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -1483,6 +1483,16 @@ config SENSORS_THMC50 This driver can also be built as a module. If so, the module will be called thmc50. +config SENSORS_TI_LMU + tristate "Texas Instruments LMU Hardware Fault Monitoring Driver" + depends on MFD_TI_LMU + help + Say Y here to include support for the TI LMU opened and shorted + circuit fault detection. + + This driver can also be built as a module. If so the module + will be called ti-lmu-hwmon. + config SENSORS_TMP102 tristate "Texas Instruments TMP102" depends on I2C diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 9e0f3dd..de11b74 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -143,6 +143,7 @@ obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o obj-$(CONFIG_SENSORS_AMC6821) += amc6821.o obj-$(CONFIG_SENSORS_TC74) += tc74.o obj-$(CONFIG_SENSORS_THMC50) += thmc50.o +obj-$(CONFIG_SENSORS_TI_LMU) += ti-lmu-hwmon.o obj-$(CONFIG_SENSORS_TMP102) += tmp102.o obj-$(CONFIG_SENSORS_TMP103) += tmp103.o obj-$(CONFIG_SENSORS_TMP401) += tmp401.o diff --git a/drivers/hwmon/ti-lmu-hwmon.c b/drivers/hwmon/ti-lmu-hwmon.c new file mode 100644 index 0000000..c297cf9 --- /dev/null +++ b/drivers/hwmon/ti-lmu-hwmon.c @@ -0,0 +1,393 @@ +/* + * TI LMU(Lighting Management Unit) Hardware Fault Monitoring Driver + * + * Copyright 2015 Texas Instruments + * + * Author: Milo Kim + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define LMU_BANK_MASK(n) (~BIT(n) & 0x07) +#define LMU_BL_MAX_CHANNELS 3 +#define LMU_DEFAULT_BANK 0 +#define LMU_DELAY_STARTUP 500 +#define LMU_DELAY_FEEDBACK 5 +#define LMU_ENABLE_FEEDBACK (BIT(0) | BIT(1) | BIT(2)) +#define LMU_MAX_BRIGHTNESS 0xFF +#define LMU_NO_RAMP 0 + +enum ti_lmu_hwmon_id { + LMU_HWMON_OPEN, + LMU_HWMON_SHORT, +}; + +/** + * struct ti_lmu_reg + * + * @monitor: Enable monitoring register + * @bank: Bank configuration register + * @ramp: Ramp(speed) configuration register + * @imax: Current limit setting register + * @feedback: Feedback enable register + * @brightness: Brightness register + * @enable: Bank enable register + * @open_fault: Detect opened circuit status register + * @short_fault: Detect shorted circuit status register + * + * To detect hardware fault, several registers are used. + * Device specific register addresses are configured in this structure. + */ +struct ti_lmu_reg { + u8 monitor; + u8 bank; + u8 ramp; + u8 imax; + u8 feedback; + u8 brightness; + u8 enable; + u8 open_fault; + u8 short_fault; +}; + +struct ti_lmu_hwmon { + struct ti_lmu *lmu; + struct device *dev; /* hwmon dev */ + const struct ti_lmu_reg *regs; +}; + +struct ti_lmu_hwmon_data { + const char *name; + const struct attribute_group **groups; + const struct ti_lmu_reg *regs; +}; + +static void ti_lmu_hwmon_reset_device(struct ti_lmu_hwmon *hwmon) +{ + unsigned int en_gpio = hwmon->lmu->en_gpio; + + /* POR(power on reset) by enable pin control */ + gpio_set_value(en_gpio, 0); + msleep(LMU_DELAY_STARTUP); + + gpio_set_value(en_gpio, 1); + msleep(LMU_DELAY_STARTUP); +} + +static int ti_lmu_hwmon_enable_monitoring(struct ti_lmu_hwmon *hwmon, + enum ti_lmu_hwmon_id id) +{ + struct ti_lmu *lmu = hwmon->lmu; + u8 reg = hwmon->regs->monitor; + + if (id == LMU_HWMON_OPEN) + return ti_lmu_write_byte(lmu, reg, BIT(0)); + else if (id == LMU_HWMON_SHORT) + return ti_lmu_write_byte(lmu, reg, BIT(1)); + else + return -EINVAL; +} + +static int ti_lmu_hwmon_assign_bank(struct ti_lmu_hwmon *hwmon, u8 val) +{ + return ti_lmu_write_byte(hwmon->lmu, hwmon->regs->bank, val); +} + +static int ti_lmu_hwmon_channel_config(struct ti_lmu_hwmon *hwmon) +{ + struct ti_lmu *lmu = hwmon->lmu; + const struct ti_lmu_reg *reg = hwmon->regs; + int ret; + + /* Set ramp time to the fatest setting */ + ret = ti_lmu_write_byte(lmu, reg->ramp, LMU_NO_RAMP); + if (ret) + return ret; + + /* Set max current to 20mA */ + ret = ti_lmu_write_byte(lmu, reg->imax, LMU_IMAX_20mA); + if (ret) + return ret; + + /* Enable feedback */ + ret = ti_lmu_write_byte(lmu, reg->feedback, LMU_ENABLE_FEEDBACK); + if (ret) + return ret; + + /* Set max brightness */ + ret = ti_lmu_write_byte(lmu, reg->brightness, LMU_MAX_BRIGHTNESS); + if (ret) + return ret; + + /* Enable a bank */ + ret = ti_lmu_write_byte(lmu, reg->enable, 1); + if (ret) + return ret; + + /* Wait until device completes fault detection */ + msleep(LMU_DELAY_FEEDBACK); + + return 0; +} + +static int ti_lmu_hwmon_get_open_fault_result(struct ti_lmu_hwmon *hwmon, + char *result) +{ + int ret, channel, len, offset = 0; + u8 status = 0; + + ret = ti_lmu_read_byte(hwmon->lmu, hwmon->regs->open_fault, &status); + if (ret) + return ret; + + for (channel = 0; channel < LMU_BL_MAX_CHANNELS; channel++) { + if (BIT(channel) & status) + len = sprintf(&result[offset], "Channel %d is opened\n", + channel); + else + len = sprintf(&result[offset], "Channel %d works\n", + channel); + + offset += len; + } + + return 0; +} + +static ssize_t ti_lmu_hwmon_get_short_fault_result(struct ti_lmu_hwmon *hwmon, + char *buf, int channel) +{ + int ret; + u8 status = 0; + + ret = ti_lmu_read_byte(hwmon->lmu, hwmon->regs->short_fault, &status); + if (ret) + return ret; + + if (BIT(channel) & status) + return sprintf(buf, "Channel %d is shorted\n", channel); + else + return sprintf(buf, "Channel %d works\n", channel); +} + +static int ti_lmu_hwmon_disable_all_banks(struct ti_lmu_hwmon *hwmon) +{ + return ti_lmu_write_byte(hwmon->lmu, hwmon->regs->enable, 0); +} + +static int ti_lmu_hwmon_notifier_call_chain(struct ti_lmu_hwmon *hwmon) +{ + int ret; + + ti_lmu_hwmon_reset_device(hwmon); + + ret = blocking_notifier_call_chain(&hwmon->lmu->notifier, + LMU_EVENT_HWMON_DONE, NULL); + if (ret == NOTIFY_OK || ret == NOTIFY_DONE) + return 0; + else + return -EINVAL; +} + +static ssize_t ti_lmu_hwmon_open_fault_show(struct device *dev, + struct device_attribute *attr, + char *buffer) +{ + struct ti_lmu_hwmon *hwmon = dev_get_drvdata(dev); + char result[100]; + int ret; + + /* Device should be reset prior to fault detection */ + ti_lmu_hwmon_reset_device(hwmon); + + ret = ti_lmu_hwmon_enable_monitoring(hwmon, LMU_HWMON_OPEN); + if (ret) + return ret; + + ret = ti_lmu_hwmon_assign_bank(hwmon, LMU_DEFAULT_BANK); + if (ret) + return ret; + + ret = ti_lmu_hwmon_channel_config(hwmon); + if (ret) + return ret; + + memset(result, 0, sizeof(result)); + ret = ti_lmu_hwmon_get_open_fault_result(hwmon, result); + if (ret) + return ret; + + /* Notify an event */ + ret = ti_lmu_hwmon_notifier_call_chain(hwmon); + if (ret) + dev_warn(dev, "Notify hwmon err\n"); + + return snprintf(buffer, PAGE_SIZE, "%s\n", result); +} + +static ssize_t ti_lmu_hwmon_short_fault_show(struct device *dev, + struct device_attribute *attr, + char *buffer) +{ + struct ti_lmu_hwmon *hwmon = dev_get_drvdata(dev); + int ret, i, len, offset = 0; + char result[100]; + + /* Device should be reset prior to fault detection */ + ti_lmu_hwmon_reset_device(hwmon); + + ret = ti_lmu_hwmon_enable_monitoring(hwmon, LMU_HWMON_SHORT); + if (ret) + return ret; + + memset(result, 0, sizeof(result)); + + /* Shorted circuit detection is done by checking the bank one by one */ + for (i = 0; i < LMU_BL_MAX_CHANNELS; i++) { + ret = ti_lmu_hwmon_assign_bank(hwmon, LMU_BANK_MASK(i)); + if (ret) + return ret; + + ret = ti_lmu_hwmon_channel_config(hwmon); + if (ret) + return ret; + + len = ti_lmu_hwmon_get_short_fault_result(hwmon, + &result[offset], i); + if (len < 0) + return len; + + offset += len; + + ret = ti_lmu_hwmon_disable_all_banks(hwmon); + if (ret) + return ret; + } + + /* Notify an event */ + ret = ti_lmu_hwmon_notifier_call_chain(hwmon); + if (ret) + dev_warn(dev, "Notify hwmon err\n"); + + return snprintf(buffer, PAGE_SIZE, "%s\n", result); +} + +static DEVICE_ATTR(open_fault, S_IRUGO, ti_lmu_hwmon_open_fault_show, NULL); +static DEVICE_ATTR(short_fault, S_IRUGO, ti_lmu_hwmon_short_fault_show, NULL); + +static struct attribute *ti_lmu_hwmon_attrs[] = { + &dev_attr_open_fault.attr, + &dev_attr_short_fault.attr, + NULL, +}; +ATTRIBUTE_GROUPS(ti_lmu_hwmon); + +/* + * Operations are dependent on the device. + * Device registers configuration is required. + */ +static const struct ti_lmu_reg lm3633_regs = { + .monitor = LM3633_REG_MONITOR_ENABLE, + .bank = LM3633_REG_HVLED_OUTPUT_CFG, + .ramp = LM3633_REG_BL0_RAMPUP, + .imax = LM3633_REG_IMAX_HVLED_A, + .feedback = LM3633_REG_BL_FEEDBACK_ENABLE, + .brightness = LM3633_REG_BRT_HVLED_A_MSB, + .enable = LM3633_REG_ENABLE, + .open_fault = LM3633_REG_BL_OPEN_FAULT_STATUS, + .short_fault = LM3633_REG_BL_SHORT_FAULT_STATUS, +}; + +static const struct ti_lmu_reg lm3697_regs = { + .monitor = LM3697_REG_MONITOR_ENABLE, + .bank = LM3697_REG_HVLED_OUTPUT_CFG, + .ramp = LM3697_REG_BL0_RAMPUP, + .imax = LM3697_REG_IMAX_A, + .feedback = LM3697_REG_FEEDBACK_ENABLE, + .brightness = LM3697_REG_BRT_A_MSB, + .enable = LM3697_REG_ENABLE, + .open_fault = LM3697_REG_OPEN_FAULT_STATUS, + .short_fault = LM3697_REG_SHORT_FAULT_STATUS, +}; + +static const struct ti_lmu_hwmon_data lm3633_hwmon_data = { + .name = "lm3633_fault_status", + .groups = ti_lmu_hwmon_groups, + .regs = &lm3633_regs, +}; + +static const struct ti_lmu_hwmon_data lm3697_hwmon_data = { + .name = "lm3697_fault_status", + .groups = ti_lmu_hwmon_groups, + .regs = &lm3697_regs, +}; + +static const struct of_device_id ti_lmu_hwmon_of_match[] = { + { .compatible = "ti,lm3633-hwmon", .data = &lm3633_hwmon_data }, + { .compatible = "ti,lm3697-hwmon", .data = &lm3697_hwmon_data }, + { } +}; +MODULE_DEVICE_TABLE(of, ti_lmu_hwmon_of_match); + +static int ti_lmu_hwmon_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct ti_lmu *lmu = dev_get_drvdata(dev->parent); + const struct of_device_id *match; + struct ti_lmu_hwmon *hwmon; + const struct ti_lmu_hwmon_data *data; + + match = of_match_device(ti_lmu_hwmon_of_match, dev); + if (!match) + return -ENODEV; + + /* To monitor hardware fault, enable pin control should be required. */ + if (!gpio_is_valid(lmu->en_gpio)) + return -EINVAL; + + hwmon = devm_kzalloc(dev, sizeof(*hwmon), GFP_KERNEL); + if (!hwmon) + return -ENOMEM; + + /* + * Get device specific data(name, groups and registers) from + * of_match table. + */ + data = (struct ti_lmu_hwmon_data *)match->data; + hwmon->lmu = lmu; + hwmon->regs = data->regs; + + hwmon->dev = devm_hwmon_device_register_with_groups(dev, data->name, + hwmon, data->groups); + + return PTR_ERR_OR_ZERO(hwmon->dev); +} + +static struct platform_driver ti_lmu_hwmon_driver = { + .probe = ti_lmu_hwmon_probe, + .driver = { + .name = "ti-lmu-hwmon", + .of_match_table = ti_lmu_hwmon_of_match, + }, +}; + +module_platform_driver(ti_lmu_hwmon_driver); + +MODULE_DESCRIPTION("TI LMU Hardware Fault Monitoring Driver"); +MODULE_AUTHOR("Milo Kim"); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("platform:ti-lmu-hwmon"); -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/