Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S932079AbbKJQIg (ORCPT ); Tue, 10 Nov 2015 11:08:36 -0500 Received: from mail-wm0-f43.google.com ([74.125.82.43]:37024 "EHLO mail-wm0-f43.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1754392AbbKJQHz (ORCPT ); Tue, 10 Nov 2015 11:07:55 -0500 From: Marc Titinger To: jic23@kernel.org, knaack.h@gmx.de, lars@metafoo.de, pmeerw@pmeerw.net Cc: linux-iio@vger.kernel.org, linux-kernel@vger.kernel.org, mturquette@baylibre.com, bcousson@baylibre.com, ptitiano@baylibre.com, Marc Titinger Subject: [RFC 1/4] iio: ina2xx: add direct IO support for TI INA2xx Power Monitors Date: Tue, 10 Nov 2015 17:07:30 +0100 Message-Id: <1447171653-12756-2-git-send-email-mtitinger@baylibre.com> X-Mailer: git-send-email 1.9.1 In-Reply-To: <1447171653-12756-1-git-send-email-mtitinger@baylibre.com> References: <1447171653-12756-1-git-send-email-mtitinger@baylibre.com> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 12865 Lines: 481 Basic support or direct IO raw read, with averaging attribute. Values are RAW, INT_PLUS_MICRO (Volt/Ampere/Watt). IIO context has 1 devices: iio:device0: ina226 4 channels found: power3: (input) 1 channel-specific attributes found: attr 0: raw value: 1.150000 voltage0: (input) 1 channel-specific attributes found: attr 0: raw value: 0.000003 voltage1: (input) 1 channel-specific attributes found: attr 0: raw value: 4.277500 current2: (input) 1 channel-specific attributes found: attr 0: raw value: 0.268000 2 device-specific attributes found: attr 0: in_calibscale value: 10000 attr 1: in_mean_raw value: 4 Signed-off-by: Marc Titinger --- drivers/iio/adc/Kconfig | 9 + drivers/iio/adc/Makefile | 1 + drivers/iio/adc/ina2xx-iio.c | 404 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 414 insertions(+) create mode 100644 drivers/iio/adc/ina2xx-iio.c diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig index eb0cd89..b648051 100644 --- a/drivers/iio/adc/Kconfig +++ b/drivers/iio/adc/Kconfig @@ -10,6 +10,15 @@ config AD_SIGMA_DELTA select IIO_BUFFER select IIO_TRIGGERED_BUFFER +config INA2XX_IIO + tristate "Texas Instruments INA2xx Power Monitors IIO driver" + depends on I2C + help + Say yes here to build support for TI INA2xx familly Power Monitors. + + Note that this is not the existing hwmon interface for this device. + + config AD7266 tristate "Analog Devices AD7265/AD7266 ADC driver" depends on SPI_MASTER diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile index a096210..e6a844a 100644 --- a/drivers/iio/adc/Makefile +++ b/drivers/iio/adc/Makefile @@ -5,6 +5,7 @@ # When adding new entries keep the list in alphabetical order obj-$(CONFIG_AD_SIGMA_DELTA) += ad_sigma_delta.o obj-$(CONFIG_AD7266) += ad7266.o +obj-$(CONFIG_INA2XX_IIO) += ina2xx-iio.o obj-$(CONFIG_AD7291) += ad7291.o obj-$(CONFIG_AD7298) += ad7298.o obj-$(CONFIG_AD7923) += ad7923.o diff --git a/drivers/iio/adc/ina2xx-iio.c b/drivers/iio/adc/ina2xx-iio.c new file mode 100644 index 0000000..257d8d5 --- /dev/null +++ b/drivers/iio/adc/ina2xx-iio.c @@ -0,0 +1,404 @@ +/* + * INA2XX Current and Power Monitors + * + * Copyright 2015 Baylibre SAS. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Based on linux/drivers/iio/adc/ad7291.c + * Copyright 2010-2011 Analog Devices Inc. + * + * Based on linux/drivers/hwmon/ina2xx.c + * Copyright 2012 Lothar Felten + * + * Licensed under the GPL-2 or later. + */ +#include +#include +#include +#include +#include + +#include + +/* + * INA2XX registers definition + */ +/* common register definitions */ +#define INA2XX_CONFIG 0x00 +#define INA2XX_SHUNT_VOLTAGE 0x01 /* readonly */ +#define INA2XX_BUS_VOLTAGE 0x02 /* readonly */ +#define INA2XX_POWER 0x03 /* readonly */ +#define INA2XX_CURRENT 0x04 /* readonly */ +#define INA2XX_CALIBRATION 0x05 + +/* register count */ +#define INA219_REGISTERS 6 +#define INA226_REGISTERS 8 +#define INA2XX_MAX_REGISTERS 8 + +/* settings - depend on use case */ +#define INA219_CONFIG_DEFAULT 0x399F /* PGA=8 */ +#define INA226_CONFIG_DEFAULT 0x4327 +#define INA226_DEFAULT_AVG 4 + +#define INA2XX_RSHUNT_DEFAULT 10000 + +/* bit mask for reading the averaging setting in the configuration register */ +#define INA226_AVG_RD_MASK 0x0E00 +#define INA226_READ_AVG(reg) (((reg) & INA226_AVG_RD_MASK) >> 9) +#define INA226_SHIFT_AVG(val) ((val) << 9) + +static struct regmap_config ina2xx_regmap_config = { + .reg_bits = 8, + .val_bits = 16, +}; + +enum ina2xx_ids { ina219, ina226 }; + +struct ina2xx_config { + u16 config_default; + int calibration_factor; + int registers; + int shunt_div; + int bus_voltage_shift; + int bus_voltage_lsb; /* uV */ + int power_lsb; /* uW */ +}; + +struct ina2xx_chip_info { + struct iio_dev *indio_dev; + const struct ina2xx_config *config; + struct mutex state_lock; + long rshunt; + int avg; + int freq; + int period_us; + struct regmap *regmap; +}; + +static const struct ina2xx_config ina2xx_config[] = { + [ina219] = { + .config_default = INA219_CONFIG_DEFAULT, + .calibration_factor = 40960000, + .registers = INA219_REGISTERS, + .shunt_div = 100, + .bus_voltage_shift = 3, + .bus_voltage_lsb = 4000, + .power_lsb = 20000, + }, + [ina226] = { + .config_default = INA226_CONFIG_DEFAULT, + .calibration_factor = 5120000, + .registers = INA226_REGISTERS, + .shunt_div = 400, + .bus_voltage_shift = 0, + .bus_voltage_lsb = 1250, + .power_lsb = 25000, + }, +}; + +static int ina2xx_get_value(struct ina2xx_chip_info *chip, u8 reg, + unsigned int regval, int *val, int *uval) +{ + *val = 0; + + switch (reg) { + case INA2XX_SHUNT_VOLTAGE: + /* signed register */ + *uval = DIV_ROUND_CLOSEST((s16) regval, + chip->config->shunt_div); + *val = *uval/1000000; + *uval = *uval - *val*1000000; + return IIO_VAL_INT_PLUS_MICRO; + + case INA2XX_BUS_VOLTAGE: + *uval = (regval >> chip->config->bus_voltage_shift) + * chip->config->bus_voltage_lsb; + *val = *uval/1000000; + *uval = *uval - *val*1000000; + return IIO_VAL_INT_PLUS_MICRO; + + case INA2XX_POWER: + *uval = regval * chip->config->power_lsb; + *val = *uval/1000000; + *uval = *uval - *val*1000000; + return IIO_VAL_INT_PLUS_MICRO; + + case INA2XX_CURRENT: + /* signed register, LSB=1mA (selected), in mA */ + *uval = (s16) regval * 1000; + return IIO_VAL_INT_PLUS_MICRO; + + case INA2XX_CALIBRATION: + *val = DIV_ROUND_CLOSEST(chip->config->calibration_factor, + regval); + return IIO_VAL_INT; + + default: + /* programmer goofed */ + WARN_ON_ONCE(1); + } + return -EINVAL; +} + +static int ina2xx_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, long mask) +{ + int ret; + struct ina2xx_chip_info *chip = iio_priv(indio_dev); + unsigned int regval; + + switch (mask) { + case IIO_CHAN_INFO_RAW: + ret = regmap_read(chip->regmap, chan->address, ®val); + if (ret < 0) + return ret; + + return ina2xx_get_value(chip, chan->address, regval, val, val2); + + case IIO_CHAN_INFO_AVERAGE_RAW: + *val = chip->avg; + return IIO_VAL_INT; + + case IIO_CHAN_INFO_CALIBSCALE: + ret = regmap_read(chip->regmap, INA2XX_CALIBRATION, ®val); + if (ret < 0) + return ret; + + return ina2xx_get_value(chip, INA2XX_CALIBRATION, regval, + val, val2); + + default: + return -EINVAL; + } + + return 0; +} + +static int ina2xx_calibrate(struct ina2xx_chip_info *chip) +{ + u16 val = DIV_ROUND_CLOSEST(chip->config->calibration_factor, + chip->rshunt); + + return regmap_write(chip->regmap, INA2XX_CALIBRATION, val); +} + + +/* + * Available averaging rates for ina226. The indices correspond with + * the bit values expected by the chip (according to the ina226 datasheet, + * table 3 AVG bit settings, found at + * http://www.ti.com/lit/ds/symlink/ina226.pdf. + */ +static const int ina226_avg_tab[] = { 1, 4, 16, 64, 128, 256, 512, 1024 }; + +static unsigned int ina226_set_average(struct ina2xx_chip_info *chip, + unsigned int val, + unsigned int *config) +{ + int bits; + + if (val > 1024 || val < 1) + return -EINVAL; + + bits = find_closest(val, ina226_avg_tab, + ARRAY_SIZE(ina226_avg_tab)); + + chip->avg = ina226_avg_tab[bits]; + + *config &= ~INA226_AVG_RD_MASK; + *config |= INA226_SHIFT_AVG(bits) & INA226_AVG_RD_MASK; + + return 0; +} + +static int ina2xx_write_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int val, int val2, long mask) +{ + struct ina2xx_chip_info *chip = iio_priv(indio_dev); + int ret = 0; + unsigned int config, tmp; + + mutex_lock(&chip->state_lock); + + ret = regmap_read(chip->regmap, INA2XX_CONFIG, &config); + if (ret < 0) + goto _err; + + tmp = config; + + switch (mask) { + case IIO_CHAN_INFO_AVERAGE_RAW: + + ret = ina226_set_average(chip, val, &tmp); + break; + + default: + ret = -EINVAL; + } + + if (!ret && (tmp != config)) + ret = regmap_write(chip->regmap, INA2XX_CONFIG, config); +_err: + mutex_unlock(&chip->state_lock); + + return ret; +} + +#define INA2XX_CHAN(_type, _index, _address) { \ + .type = _type, \ + .address = _address, \ + .indexed = 1, \ + .channel = (_index), \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_dir = BIT(IIO_CHAN_INFO_AVERAGE_RAW) | \ + BIT(IIO_CHAN_INFO_CALIBSCALE), \ + .scan_index = (_index), \ + .scan_type = { \ + .sign = 'u', \ + .realbits = 16, \ + .storagebits = 16, \ + .shift = 0, \ + .endianness = IIO_BE, \ + } \ +} + +static const struct iio_chan_spec ina2xx_channels[] = { + INA2XX_CHAN(IIO_VOLTAGE, 0, INA2XX_SHUNT_VOLTAGE), + INA2XX_CHAN(IIO_VOLTAGE, 1, INA2XX_BUS_VOLTAGE), + INA2XX_CHAN(IIO_CURRENT, 2, INA2XX_CURRENT), + INA2XX_CHAN(IIO_POWER, 3, INA2XX_POWER), + IIO_CHAN_SOFT_TIMESTAMP(4), +}; + +static const struct iio_info ina2xx_info = { + .read_raw = &ina2xx_read_raw, + .write_raw = &ina2xx_write_raw, + .driver_module = THIS_MODULE, +}; + +/* +* Initialize the configuration and calibration registers. +*/ +static int ina2xx_init(struct ina2xx_chip_info *chip, unsigned int config) +{ + int ret = regmap_write(chip->regmap, INA2XX_CONFIG, config); + + if (ret < 0) + return ret; + /* + * Set current LSB to 1mA, shunt is in uOhms + * (equation 13 in datasheet). + */ + return ina2xx_calibrate(chip); +} + +static int ina2xx_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct ina2xx_chip_info *chip; + struct iio_dev *indio_dev; + int ret; + unsigned int val; + + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*chip)); + if (!indio_dev) + return -ENOMEM; + + chip = iio_priv(indio_dev); + chip->indio_dev = indio_dev; + + /* set the device type */ + chip->config = &ina2xx_config[id->driver_data]; + + if (of_property_read_u32(client->dev.of_node, + "shunt-resistor", &val) < 0) { + struct ina2xx_platform_data *pdata = + dev_get_platdata(&client->dev); + + if (pdata) + val = pdata->shunt_uohms; + else + val = INA2XX_RSHUNT_DEFAULT; + } + + if (val <= 0 || val > chip->config->calibration_factor) + return -ENODEV; + + chip->rshunt = val; + + ina2xx_regmap_config.max_register = chip->config->registers; + + mutex_init(&chip->state_lock); + + /* this is only used for device removal purposes */ + i2c_set_clientdata(client, indio_dev); + + indio_dev->name = id->name; + indio_dev->channels = ina2xx_channels; + indio_dev->num_channels = ARRAY_SIZE(ina2xx_channels); + + indio_dev->dev.parent = &client->dev; + indio_dev->info = &ina2xx_info; + indio_dev->modes = INDIO_DIRECT_MODE; + + chip->regmap = devm_regmap_init_i2c(client, &ina2xx_regmap_config); + if (IS_ERR(chip->regmap)) { + dev_err(&client->dev, "failed to allocate register map\n"); + return PTR_ERR(chip->regmap); + } + + /* Patch the current config register with default. */ + val = chip->config->config_default; + if (id->driver_data == ina226) + ina226_set_average(chip, INA226_DEFAULT_AVG, &val); + + ret = ina2xx_init(chip, val); + if (ret < 0) { + dev_err(&client->dev, "error configuring the device: %d\n", + ret); + return -ENODEV; + } + + return iio_device_register(indio_dev); +} + +static int ina2xx_remove(struct i2c_client *client) +{ + struct iio_dev *indio_dev = i2c_get_clientdata(client); + + iio_device_unregister(indio_dev); + + return 0; +} + +static const struct i2c_device_id ina2xx_id[] = { + {"ina219", ina219}, + {"ina220", ina219}, + {"ina226", ina226}, + {"ina230", ina226}, + {"ina231", ina226}, + {} +}; + +MODULE_DEVICE_TABLE(i2c, ina2xx_id); + +static struct i2c_driver ina2xx_driver = { + .driver = { + .name = KBUILD_MODNAME, + }, + .probe = ina2xx_probe, + .remove = ina2xx_remove, + .id_table = ina2xx_id, +}; + +module_i2c_driver(ina2xx_driver); + +MODULE_AUTHOR("Marc Titinger "); +MODULE_DESCRIPTION("Texas Instruments INA2XX ADC driver"); +MODULE_LICENSE("GPL v2"); -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/