Return-Path: <linux-kernel-owner@vger.kernel.org>
Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand
	id S1754301AbbKLQTu (ORCPT <rfc822;w@1wt.eu>);
	Thu, 12 Nov 2015 11:19:50 -0500
Received: from smtp2-g21.free.fr ([212.27.42.2]:43139 "EHLO smtp2-g21.free.fr"
	rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP
	id S1751769AbbKLQTs (ORCPT <rfc822;linux-kernel@vger.kernel.org>);
	Thu, 12 Nov 2015 11:19:48 -0500
Subject: Re: [PATCH v5] net: ethernet: add driver for Aurora VLSI NB8800
 Ethernet controller
To: Mans Rullgard <mans@mansr.com>
Cc: linux-kernel@vger.kernel.org, netdev@vger.kernel.org,
        Florian Fainelli <f.fainelli@gmail.com>,
        Daniel Mack <daniel@zonque.org>,
        "David S. Miller" <davem@davemloft.net>,
        Fabio Estevam <festevam@gmail.com>
References: <1447172063-27234-1-git-send-email-mans@mansr.com>
 <564241BF.4020700@free.fr> <yw1xbnb1r70r.fsf@unicorn.mansr.com>
 <5644953C.8000800@free.fr> <yw1xfv0bmhz3.fsf@unicorn.mansr.com>
From: Mason <slash.tmp@free.fr>
Message-ID: <5644BC1B.1000109@free.fr>
Date: Thu, 12 Nov 2015 17:19:39 +0100
User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:41.0) Gecko/20100101
 Firefox/41.0 SeaMonkey/2.38
MIME-Version: 1.0
In-Reply-To: <yw1xfv0bmhz3.fsf@unicorn.mansr.com>
Content-Type: text/plain; charset=ISO-8859-1
Content-Transfer-Encoding: 8bit
Sender: linux-kernel-owner@vger.kernel.org
List-ID: <linux-kernel.vger.kernel.org>
X-Mailing-List: linux-kernel@vger.kernel.org
Content-Length: 3099
Lines: 94

[ CCing a few knowledgeable people ]

Despite the subject, this is about an Atheros 8035 PHY :-)

On 12/11/2015 15:04, M?ns Rullg?rd wrote:

> Mason wrote:
> 
>> BTW, you're not using the PHY IRQ, right? I think I remember you saying
>> it didn't work reliably?
> 
> It doesn't seem to be wired up on any of my boards, or there's some
> magic required to activate it that I'm unaware of.

Weird. The board schematics for the 1172 show Tango ETH0_MDINT# pin
properly connected to AR8035 INT pin (pin 20).

<Thinking out loud>

http://www.redeszone.net/app/uploads/2014/04/AR8035.pdf

INT pin 20
I/O, D, PD
Interrupt Signal to System; default OD-gate, needs an external
10Kohm pull-up, active low; can be configured to I/O by register,
active high.


4.1.17 Interrupt Enable
Offset: 0x12
Mode: Read/Write
Hardware Reset: 0


Strange... it looks like AT803X_INER and AT803X_INTR_ENABLE refer to
the same "Interrupt Enable" register?

In fact, AT803X_INER_INIT == 0xec00 makes sense for register 0x12:
link success/fail, speed/duplex changed, autoneg error

Looks like at803x_config_intr() is used for 8031, but not for 8035...

Relevant commit:
77a9939426f7a "phy/at8031: enable at8031 to work on interrupt mode"

If I add .config_intr and .ack_interrupt to the 8035 struct, then I get
(also added some traces)

[    0.883517] *** at803x_config_intr: ENABLE
[    1.576108] *** at803x_config_intr: DISABLE
[    1.580467] *** at803x_config_intr: ENABLE
[    1.584959] *** at803x_config_intr: DISABLE
[    1.589297] *** at803x_config_intr: ENABLE
[    4.321722] *** at803x_config_intr: DISABLE
[    4.326054] *** at803x_config_intr: ENABLE
[    4.330489] nb8800 26000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    4.338335] *** at803x_config_intr: ENABLE

(Are all the ENABLE/DISABLE events expected?)

And if I unplug/replug the Ethernet cable,

[   71.903051] *** at803x_config_intr: DISABLE
[   71.907410] *** at803x_config_intr: ENABLE
[   71.912232] nb8800 26000.ethernet eth0: Link is Down
[   71.917309] *** at803x_config_intr: ENABLE
[   78.008972] *** at803x_config_intr: DISABLE
[   78.013375] *** at803x_config_intr: ENABLE
[   78.017797] nb8800 26000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   78.025702] *** at803x_config_intr: ENABLE

(Are all the ENABLE/DISABLE events expected there too?)

# cat /proc/interrupts 
            CPU0       CPU1       
 18:        107          0      irq0   1 Level     serial
 54:          5          0      irq0  37 Edge      phy_interrupt
 55:       4953          0      irq0  38 Level     eth0
211:       1147        254       GIC  29 Edge      twd


Questions:

Can't at803x_ack_interrupt() just return phy_read(phydev, AT803X_INSR);
Can at803x_config_intr() be used with the 8035
What about AT803X_INER/AT803X_INTR_ENABLE and AT803X_INSR/AT803X_INTR_STATUS

Regards.

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/