Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1752396AbbKOVg0 (ORCPT ); Sun, 15 Nov 2015 16:36:26 -0500 Received: from ns.gsystem.sk ([62.176.172.50]:47261 "EHLO gsystem.sk" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751351AbbKOVgY (ORCPT ); Sun, 15 Nov 2015 16:36:24 -0500 From: Ondrej Zary To: netdev@vger.kernel.org Cc: Francois Romieu , David Miller , Kernel development list Subject: [PATCH 1/2 v2] dl2k: Add support for IP1000A-based cards Date: Sun, 15 Nov 2015 22:36:11 +0100 Message-Id: <1447623372-29031-1-git-send-email-linux@rainbow-software.org> X-Mailer: git-send-email 1.7.10.4 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 7314 Lines: 225 Add support for IP1000A chips to dl2k driver. IP1000A chip looks like a TC9020 with integrated PHY. This allows IP1000A chips to work reliably because the ipg driver is buggy - it loses packets under load and then completely stops transmitting data. Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps: vendor=0x13f0 device=0x1023 (rev 0x41) subsystem vendor=0x1043 device=0x8180 MAC address registers access needed to be changed from 8-bit to 16-bit because 8-bit does not work on IP1000A. 8-bit access is not even allowed in the TC9020 datasheet (although it worked). 16-bit access works on both. Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably a rebranded TC9020): vendor=0x1186 device=0x4000 (rev 0x0c) subsystem vendor=0x1186 device=0x4000 Signed-off-by: Ondrej Zary --- drivers/net/ethernet/dlink/Kconfig | 5 ++-- drivers/net/ethernet/dlink/dl2k.c | 55 ++++++++++++++++++++++++++++++++++-- drivers/net/ethernet/dlink/dl2k.h | 15 +++++++++- 3 files changed, 69 insertions(+), 6 deletions(-) diff --git a/drivers/net/ethernet/dlink/Kconfig b/drivers/net/ethernet/dlink/Kconfig index f6e858d..ebdc832 100644 --- a/drivers/net/ethernet/dlink/Kconfig +++ b/drivers/net/ethernet/dlink/Kconfig @@ -17,15 +17,16 @@ config NET_VENDOR_DLINK if NET_VENDOR_DLINK config DL2K - tristate "DL2000/TC902x-based Gigabit Ethernet support" + tristate "DL2000/TC902x/IP1000A-based Gigabit Ethernet support" depends on PCI select CRC32 ---help--- - This driver supports DL2000/TC902x-based Gigabit ethernet cards, + This driver supports DL2000/TC902x/IP1000A-based Gigabit ethernet cards, which includes D-Link DGE-550T Gigabit Ethernet Adapter. D-Link DL2000-based Gigabit Ethernet Adapter. Sundance/Tamarack TC902x Gigabit Ethernet Adapter. + ICPlus IP1000A-based cards To compile this driver as a module, choose M here: the module will be called dl2k. diff --git a/drivers/net/ethernet/dlink/dl2k.c b/drivers/net/ethernet/dlink/dl2k.c index cf0a5fc..ccca479 100644 --- a/drivers/net/ethernet/dlink/dl2k.c +++ b/drivers/net/ethernet/dlink/dl2k.c @@ -253,6 +253,19 @@ rio_probe1 (struct pci_dev *pdev, const struct pci_device_id *ent) if (err) goto err_out_unmap_rx; + if (np->chip_id == CHIP_IP1000A && + (np->pdev->revision == 0x40 || np->pdev->revision == 0x41)) { + /* PHY magic taken from ipg driver, undocumented registers */ + mii_write(dev, np->phy_addr, 31, 0x0001); + mii_write(dev, np->phy_addr, 27, 0x01e0); + mii_write(dev, np->phy_addr, 31, 0x0002); + mii_write(dev, np->phy_addr, 27, 0xeb8e); + mii_write(dev, np->phy_addr, 31, 0x0000); + mii_write(dev, np->phy_addr, 30, 0x005e); + /* advertise 1000BASE-T half & full duplex, prefer MASTER */ + mii_write(dev, np->phy_addr, MII_CTRL1000, 0x0700); + } + /* Fiber device? */ np->phy_media = (dr16(ASICCtrl) & PhyMedia) ? 1 : 0; np->link_status = 0; @@ -361,6 +374,11 @@ parse_eeprom (struct net_device *dev) for (i = 0; i < 6; i++) dev->dev_addr[i] = psrom->mac_addr[i]; + if (np->chip_id == CHIP_IP1000A) { + np->led_mode = psrom->led_mode; + return 0; + } + if (np->pdev->vendor != PCI_VENDOR_ID_DLINK) { return 0; } @@ -406,6 +424,28 @@ parse_eeprom (struct net_device *dev) return 0; } +static void rio_set_led_mode(struct net_device *dev) +{ + struct netdev_private *np = netdev_priv(dev); + void __iomem *ioaddr = np->ioaddr; + u32 mode; + + if (np->chip_id != CHIP_IP1000A) + return; + + mode = dr32(ASICCtrl); + mode &= ~(IPG_AC_LED_MODE_BIT_1 | IPG_AC_LED_MODE | IPG_AC_LED_SPEED); + + if (np->led_mode & 0x01) + mode |= IPG_AC_LED_MODE; + if (np->led_mode & 0x02) + mode |= IPG_AC_LED_MODE_BIT_1; + if (np->led_mode & 0x08) + mode |= IPG_AC_LED_SPEED; + + dw32(ASICCtrl, mode); +} + static int rio_open (struct net_device *dev) { @@ -424,6 +464,8 @@ rio_open (struct net_device *dev) GlobalReset | DMAReset | FIFOReset | NetworkReset | HostReset); mdelay(10); + rio_set_led_mode(dev); + /* DebugCtrl bit 4, 5, 9 must set */ dw32(DebugCtrl, dr32(DebugCtrl) | 0x0230); @@ -433,9 +475,13 @@ rio_open (struct net_device *dev) alloc_list (dev); - /* Get station address */ - for (i = 0; i < 6; i++) - dw8(StationAddr0 + i, dev->dev_addr[i]); + /* Set station address */ + /* 16 or 32-bit access is required by TC9020 datasheet but 8-bit works + * too. However, it doesn't work on IP1000A so we use 16-bit access. + */ + for (i = 0; i < 3; i++) + dw16(StationAddr0 + 2 * i, + cpu_to_le16(((u16 *)dev->dev_addr)[i])); set_multicast (dev); if (np->coalesce) { @@ -780,6 +826,7 @@ tx_error (struct net_device *dev, int tx_status) break; mdelay (1); } + rio_set_led_mode(dev); rio_free_tx (dev, 1); /* Reset TFDListPtr */ dw32(TFDListPtr0, np->tx_ring_dma + @@ -799,6 +846,7 @@ tx_error (struct net_device *dev, int tx_status) break; mdelay (1); } + rio_set_led_mode(dev); /* Let TxStartThresh stay default value */ } /* Maximum Collisions */ @@ -965,6 +1013,7 @@ rio_error (struct net_device *dev, int int_status) dev->name, int_status); dw16(ASICCtrl + 2, GlobalReset | HostReset); mdelay (500); + rio_set_led_mode(dev); } } diff --git a/drivers/net/ethernet/dlink/dl2k.h b/drivers/net/ethernet/dlink/dl2k.h index 23c07b0..8f4f612 100644 --- a/drivers/net/ethernet/dlink/dl2k.h +++ b/drivers/net/ethernet/dlink/dl2k.h @@ -211,6 +211,10 @@ enum ASICCtrl_HiWord_bits { ResetBusy = 0x0400, }; +#define IPG_AC_LED_MODE BIT(14) +#define IPG_AC_LED_SPEED BIT(27) +#define IPG_AC_LED_MODE_BIT_1 BIT(29) + /* Transmit Frame Control bits */ enum TFC_bits { DwordAlign = 0x00000000, @@ -332,7 +336,10 @@ typedef struct t_SROM { u16 asic_ctrl; /* 0x02 */ u16 sub_vendor_id; /* 0x04 */ u16 sub_system_id; /* 0x06 */ - u16 reserved1[12]; /* 0x08-0x1f */ + u16 pci_base_1; /* 0x08 (IP1000A only) */ + u16 pci_base_2; /* 0x0a (IP1000A only) */ + u16 led_mode; /* 0x0c (IP1000A only) */ + u16 reserved1[9]; /* 0x0e-0x1f */ u8 mac_addr[6]; /* 0x20-0x25 */ u8 reserved2[10]; /* 0x26-0x2f */ u8 sib[204]; /* 0x30-0xfb */ @@ -397,6 +404,7 @@ struct netdev_private { u16 advertising; /* NWay media advertisement */ u16 negotiate; /* Negotiated media */ int phy_addr; /* PHY addresses. */ + u16 led_mode; /* LED mode read from EEPROM (IP1000A only) */ }; /* The station address location in the EEPROM. */ @@ -407,10 +415,15 @@ struct netdev_private { class_mask of the class are honored during the comparison. driver_data Data private to the driver. */ +#define CHIP_IP1000A 1 static const struct pci_device_id rio_pci_tbl[] = { {0x1186, 0x4000, PCI_ANY_ID, PCI_ANY_ID, }, {0x13f0, 0x1021, PCI_ANY_ID, PCI_ANY_ID, }, + { PCI_VDEVICE(SUNDANCE, 0x1023), CHIP_IP1000A }, + { PCI_VDEVICE(SUNDANCE, 0x2021), CHIP_IP1000A }, + { PCI_VDEVICE(DLINK, 0x9021), CHIP_IP1000A }, + { PCI_VDEVICE(DLINK, 0x4020), CHIP_IP1000A }, { } }; MODULE_DEVICE_TABLE (pci, rio_pci_tbl); -- Ondrej Zary -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/