Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S965069AbbLHORc (ORCPT ); Tue, 8 Dec 2015 09:17:32 -0500 Received: from down.free-electrons.com ([37.187.137.238]:38938 "EHLO mail.free-electrons.com" rhost-flags-OK-OK-OK-FAIL) by vger.kernel.org with ESMTP id S964904AbbLHORa (ORCPT ); Tue, 8 Dec 2015 09:17:30 -0500 Date: Tue, 8 Dec 2015 15:17:17 +0100 From: Boris Brezillon To: Harvey Hunt Cc: , devicetree@vger.kernel.org, Zubair Lutfullah Kakakhel , linux-kernel@vger.kernel.org, Alex Smith , Brian Norris , David Woodhouse Subject: Re: [PATCH v9 1/3] dt-bindings: binding for jz4780-{nand,bch} Message-ID: <20151208151717.6197165d@bbrezillon> In-Reply-To: <1449144142-24004-2-git-send-email-harvey.hunt@imgtec.com> References: <1449144142-24004-1-git-send-email-harvey.hunt@imgtec.com> <1449144142-24004-2-git-send-email-harvey.hunt@imgtec.com> X-Mailer: Claws Mail 3.11.1 (GTK+ 2.24.27; x86_64-pc-linux-gnu) MIME-Version: 1.0 Content-Type: text/plain; charset=US-ASCII Content-Transfer-Encoding: 7bit Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 5158 Lines: 161 On Thu, 3 Dec 2015 12:02:20 +0000 Harvey Hunt wrote: > From: Alex Smith > > Add DT bindings for NAND devices connected to the NEMC on JZ4780 SoCs, > as well as the hardware BCH controller, used by the jz4780_{nand,bch} > drivers. > > Signed-off-by: Alex Smith > Cc: Zubair Lutfullah Kakakhel > Cc: David Woodhouse > Cc: Brian Norris > Cc: linux-mtd@lists.infradead.org > Cc: devicetree@vger.kernel.org > Cc: linux-kernel@vger.kernel.org > Signed-off-by: Harvey Hunt FWIW: Reviewed-by: Boris Brezillon > --- > v8 -> v9: > - Document that partitions are represented as a child node of a NAND chip. > > v7 -> v8: > - Describe how NAND chips are now child nodes of the NAND controller. > > v6 -> v7: > - Add nand-ecc-mode to DT bindings. > - Add nand-on-flash-bbt to DT bindings. > > v5 -> v6: > - No change. > > v4 -> v5: > - Rename ingenic,bch-device to ingenic,bch-controller to fit with > existing convention. > > v3 -> v4: > - No change > > v2 -> v3: > - Rebase to 4.0-rc6 > - Changed ingenic,ecc-size to common nand-ecc-step-size > - Changed ingenic,ecc-strength to common nand-ecc-strength > - Changed ingenic,busy-gpio to common rb-gpios > - Changed ingenic,wp-gpio to common wp-gpios > > v1 -> v2: > - Rebase to 4.0-rc3 > > .../bindings/mtd/ingenic,jz4780-nand.txt | 86 ++++++++++++++++++++++ > 1 file changed, 86 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt > > diff --git a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt > new file mode 100644 > index 0000000..29ea585 > --- /dev/null > +++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt > @@ -0,0 +1,86 @@ > +* Ingenic JZ4780 NAND/BCH > + > +This file documents the device tree bindings for NAND flash devices on the > +JZ4780. NAND devices are connected to the NEMC controller (described in > +memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must > +be children of the NEMC node. > + > +Required NAND controller device properties: > +- compatible: Should be set to "ingenic,jz4780-nand". > +- reg: For each bank with a NAND chip attached, should specify a bank number, > + an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank). > + > +Optional NAND controller device properties: > +- ingenic,bch-controller: To make use of the hardware BCH controller, this > + property must contain a phandle for the BCH controller node. The required > + properties for this node are described below. If this is not specified, > + software BCH will be used instead. > + > +Optional children nodes: > +- Individual NAND chips are children of the NAND controller node. > + > +Required children node properties: > +- reg: An integer ranging from 1 to 6 representing the CS line to use. > + > +Optional children node properties: > +- nand-ecc-step-size: ECC block size in bytes. > +- nand-ecc-strength: ECC strength (max number of correctable bits). > +- nand-ecc-mode: String, operation mode of the NAND ecc mode. "hw" by default > +- nand-on-flash-bbt: boolean to enable on flash bbt option, if not present false > +- rb-gpios: GPIO specifier for the busy pin. > +- wp-gpios: GPIO specifier for the write protect pin. > + > +Optional child node of NAND chip nodes: > +- partitions: see Documentation/devicetree/bindings/mtd/partition.txt > + > +Example: > + > +nemc: nemc@13410000 { > + ... > + > + nandc: nand-controller@1 { > + compatible = "ingenic,jz4780-nand"; > + reg = <1 0 0x1000000>; /* Bank 1 */ > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + ingenic,bch-controller = <&bch>; > + > + nand@1 { > + reg = <1>; > + > + nand-ecc-step-size = <1024>; > + nand-ecc-strength = <24>; > + nand-ecc-mode = "hw"; > + nand-on-flash-bbt; > + > + rb-gpios = <&gpa 20 GPIO_ACTIVE_LOW>; > + wp-gpios = <&gpf 22 GPIO_ACTIVE_LOW>; > + > + partitions { > + #address-cells = <2>; > + #size-cells = <2>; > + ... > + } > + }; > + }; > +}; > + > +The BCH controller is a separate SoC component used for error correction on > +NAND devices. The following is a description of the device properties for a > +BCH controller. > + > +Required BCH properties: > +- compatible: Should be set to "ingenic,jz4780-bch". > +- reg: Should specify the BCH controller registers location and length. > +- clocks: Clock for the BCH controller. > + > +Example: > + > +bch: bch@134d0000 { > + compatible = "ingenic,jz4780-bch"; > + reg = <0x134d0000 0x10000>; > + > + clocks = <&cgu JZ4780_CLK_BCH>; > +}; -- Boris Brezillon, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/