Subject: Re: [PATCH v2 1/2] dt/bindings/usb: Add bindings for PIC32 MUSB
 driver.
To: Rob Herring <robh@kernel.org>
References: <460027775-20729-2-git-send-email-purna.mandal@microchip.com>
 <1460032381-32677-1-git-send-email-purna.mandal@microchip.com>
 <20160411151022.GA6187@rob-hp-laptop>
CC: <linux-kernel@vger.kernel.org>, <linux-usb@vger.kernel.org>,
        Joshua Henderson <digitalpeer@digitalpeer.com>,
        <devicetree@vger.kernel.org>, Kumar Gala <galak@codeaurora.org>,
        Ian Campbell <ijc+devicetree@hellion.org.uk>,
        Pawel Moll <pawel.moll@arm.com>, Mark Rutland <mark.rutland@arm.com>
From: Purna Chandra Mandal <purna.mandal@microchip.com>
Message-ID: <570CCAA8.2000102@microchip.com>
Date: Tue, 12 Apr 2016 15:45:04 +0530
User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:38.0) Gecko/20100101
 Thunderbird/38.4.0
MIME-Version: 1.0
In-Reply-To: <20160411151022.GA6187@rob-hp-laptop>
Content-Type: text/plain; charset="windows-1252"
Content-Transfer-Encoding: 7bit
Sender: linux-kernel-owner@vger.kernel.org
Content-Length: 4107
Lines: 106

On 04/11/2016 08:40 PM, Rob Herring wrote:

> On Thu, Apr 07, 2016 at 06:02:59PM +0530, Purna Chandra Mandal wrote:
>> Document devicetree binding for the USB controller
>> and USB Phy found on Microchip PIC32 class devices.
>>
>> Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
>>
>> ---
>>
>> Changes in v2: None
>>
>>  .../bindings/usb/microchip,pic32-musb.txt          | 67 ++++++++++++++++++++++
>>  1 file changed, 67 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/usb/microchip,pic32-musb.txt
>>
>> diff --git a/Documentation/devicetree/bindings/usb/microchip,pic32-musb.txt b/Documentation/devicetree/bindings/usb/microchip,pic32-musb.txt
>> new file mode 100644
>> index 0000000..e1cec9d
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/usb/microchip,pic32-musb.txt
>> @@ -0,0 +1,67 @@
>> +Microchip PIC32 MUSB DRC/OTG controller
>> +-------------------------------------------
>> +
>> +Required properties:
>> + - compatible       : should be "microchip,pic32mzda-usb".
>> + - reg              : offset and length of "MUSB Core Registers" and
>> +                      "USB Clock & Reset Registers".
>> + - reg-names        : should be "mc", and "usbcr" in order
>> + - clocks           : clock specifier for the musb controller clock
>> + - clock-names      : should be "usb_clk"
>> + - interrupts       : interrupt number for MUSB Core General interrupt
>> +                      and DMA interrupt
>> + - interrupt-names  : must be "mc" and "dma" in order.
>> + - phys             : phy specifier for the otg phy.
>> + - dr_mode          : should be one of "host", "peripheral" or "otg".
>> + - mentor,multipoint: Should be "1" indicating the musb controller supports
>> +                      multipoint. This is MUSB configuration-specific setting.
>> + - mentor,num-eps   : Specifies the number of endpoints. This is also a
>> +                      MUSB configuration-specific setting. Should be set to "8".
>> + - mentor,ram-bits  : Specifies the ram address size. Should be set to "11".
>> + - mentor,power     : Should be "500". This signifies the controller can supply
>> +                      up to 500mA when operating in host mode.
>> + - phys             : phandle of the USB phy.
>> + - usb_overcurrent  : phandle to MUSB over-current note. It should have
>> +                      interrupt number for over-current detection logic.
> This node is only an interrupt? Then you should use interrupts-extended 
> and make this interrupt the 3rd one. interrupts-extended will let you 
> have different interrupt parents for each irq.

Will use 'interrupts-extended' instead.

>> +
>> +Optional properties:
>> + - microchip,fifo-mode: Specifies layout of internal SRAM for end-point fifos.
>> +                        Should be 0 (default) or 1.
> Make this a boolean.

ack.

>> +
>> +Example:
>> +	aliases {
>> +		usb1 = &usb1;
>> +		phy1 = &usb1_phy;
>> +	};
>> +
>> +	usb1: hsusb1_core@1f8e3000 {
>> +		compatible = "microchip,pic32mzda-usb";
>> +		reg = <0x1f8e3000 0x1000>,
>> +		      <0x1f884000 0x1000>;
>> +		reg-names = "mc", "usbcr";
>> +		interrupts = <132 IRQ_TYPE_EDGE_RISING>,
>> +			     <133 IRQ_TYPE_LEVEL_HIGH>;
>> +		interrupt-names = "mc", "dma";
>> +		dr_mode = "host";
>> +		mentor,multipoint = <1>;
>> +		mentor,num-eps = <8>;
>> +		mentor,ram-bits = <11>;
>> +		mentor,power = <500>;
>> +		phys = <&usb1_phy>;
>> +		clocks = <&rootclk PB5CLK>;
>> +		clock-names = "usb_clk";
>> +		usb_overcurrent = <&usb1_overcurrent>;
>> +	};
>> +
>> +	usb1_phy: hsusb1_phy@1f8e4000 {
>> +		compatible = "usb-nop-xceiv";
>> +		reg = <0x1f8e4000 0x1000>;
>> +		clocks = <&rootclk UPLLCLK>;
>> +		clock-names = "main_clk";
>> +		clock-frequency = <24000000>;
>> +	};
>> +
>> +	usb1_overcurrent: hsusb1_oc@0 {
>> +		interrupt-parent = <&gpio1>;
>> +		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
>> +	};
>> -- 
>> 1.8.3.1
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe devicetree" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at  http://vger.kernel.org/majordomo-info.html