Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1753310AbcDSJF5 (ORCPT ); Tue, 19 Apr 2016 05:05:57 -0400 Received: from comal.ext.ti.com ([198.47.26.152]:46021 "EHLO comal.ext.ti.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752308AbcDSJFy convert rfc822-to-8bit (ORCPT ); Tue, 19 Apr 2016 05:05:54 -0400 From: "Reizer, Eyal" To: Arnd Bergmann CC: Kalle Valo , Eyal Reizer , "linux-wireless@vger.kernel.org" , "netdev@vger.kernel.org" , "linux-kernel@vger.kernel.org" , "devicetree@vger.kernel.org" , "linux-spi@vger.kernel.org" Subject: RE: [PATCHv2] wlcore: spi: add wl18xx support Thread-Topic: [PATCHv2] wlcore: spi: add wl18xx support Thread-Index: AQHRkvs3tFwJpRa2nU+to3p0n+8ju5+C0KzggAvWT4CAAJzFUIAAeeSAgAFQdyA= Date: Tue, 19 Apr 2016 09:05:45 +0000 Message-ID: <8665E2433BC68541A24DFFCA87B70F5B360C0745@DFRE01.ent.ti.com> References: <1460273570-12298-1-git-send-email-eyalr@ti.com> <14313437.cDJIgY3kzo@wuerfel> <8665E2433BC68541A24DFFCA87B70F5B360BF614@DFRE01.ent.ti.com> <1463330011.BhWEcYYuGD@wuerfel> In-Reply-To: <1463330011.BhWEcYYuGD@wuerfel> Accept-Language: en-US Content-Language: en-US X-MS-Has-Attach: X-MS-TNEF-Correlator: x-originating-ip: [10.167.188.42] x-exclaimer-md-config: f9c360f5-3d1e-4c3c-8703-f45bf52eff6b Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 8BIT MIME-Version: 1.0 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 2544 Lines: 63 Arnd, > > > > > > > > - all wilink family needs special init command for entering wspi mode. > > > > extra clock cycles should be sent after the spi init command while the > > > > cs pin is high. > > > > - switch to controling the cs pin from the spi driver for achieveing the > > > > above. > > > > - the selected cs gpio is read from the spi device-tree node using the > > > > cs-gpios field and setup as a gpio. > > > > - See the example below for specifying the cs gpio using the cs-gpios > entry > > > > &spi0 { > > > > ... > > > > cs-gpios = <&gpio0 5 0>; > > > > ... > > > > wlcore: wlcore@0 { > > > > compatible = "ti,wl1835"; > > > > ... > > > > ... > > > > }; > > > > }; > > > > > > > > Signed-off-by: Eyal Reizer > > > > > > I don't think this can work in general: not all SPI hosts uses GPIOs > > > for controlling CS, so the logic can't work, and it's also a > > > layering violation for the driver to look at the parent. > > > > > > I would suggest fixing this using a new API function from the SPI > > > core, if we don't already have a generic way to do it. > > > > > Originally this is what I have done until I was pointed to the generic > > cs-gpio mechanism in the SPI core. > > It is a generic mechanism already in the SPI core driver. > > See: Documentation/devicetree/bindings/spi/spi-bus.txt > > The cs-gpios property is documented as optional, it defines how you should > list the gpios if CS is implemented using gpio, but not all hardware does it like > this. > > > It is also part of the generic spi.h (include/Linux/spi/spi.h), > > already part of " struct spi_device" So it seemed redundant adding > > another mechanism for implementing the same. > > Platform that interact with a wilink need to use it, and platforms > > that don't have this capability will probably not interact with a wilink device > using SPI. > > The cs_gpio field in spi_device belongs to the spi host controller, no other > slave driver uses it. > > I wasn't asking for a duplication of this mechanism, but an interface to use it > properly. Internally, the spi core uses the spi_set_cs() function to pick a CS. > Find a way to use that rather than reimplementing it incorrectly. > Understood. As this special CS manipulation is unique to wspi (wilink spi) I think the best option is to move this gpio allocation into wlcore_spi as a new device tree entry used only by this driver. If you agree I will submit a v3. Best Regards, Eyal