Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1758193AbcKCP0Y (ORCPT ); Thu, 3 Nov 2016 11:26:24 -0400 Received: from mail-wm0-f52.google.com ([74.125.82.52]:37536 "EHLO mail-wm0-f52.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1757869AbcKCP0U (ORCPT ); Thu, 3 Nov 2016 11:26:20 -0400 From: Alexandre Bailon To: david@lechnology.com, b-liu@ti.com, balbi@kernel.org Cc: kishon@ti.com, khilman@baylibre.com, linux-kernel@vger.kernel.org, linux-usb@vger.kernel.org, nsekhar@ti.com, Alexandre Bailon Subject: [PATCH v3 3/5] dt/bindings: Add a new property to DA8xx USB PHY Date: Thu, 3 Nov 2016 16:26:03 +0100 Message-Id: <1478186765-19840-4-git-send-email-abailon@baylibre.com> X-Mailer: git-send-email 2.7.3 In-Reply-To: <1478186765-19840-1-git-send-email-abailon@baylibre.com> References: <1478186765-19840-1-git-send-email-abailon@baylibre.com> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 1776 Lines: 39 The USB PHY is able to operate in OTG, host or peripheral. Some board may be wired to work act only as host or peripheral. In such case, the dr_mode property of controller must be set to host or peripheral. But doing that will also configure the PHY in host or peripheral mode whereas OTG is able to detect which role the USB controller should take. The PHY's host or peripheral mode are actually only useful when hardware doesn't allow OTG to detect it's role. Add the usb20_force_mode property to force the PHY to operate in host or peripheral mode. When usb20_force_mode is used, dr_mode should also be configured to host or peripheral. The controller uses dr_mode to configure itself, but the phy use it to get the mode to use to configure the PHY mode. Signed-off-by: Alexandre Bailon --- Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt index c26478b..9fc87fb 100644 --- a/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt +++ b/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt @@ -4,6 +4,11 @@ Required properties: - compatible: must be "ti,da830-usb-phy". - #phy-cells: must be 1. +Optional properties: +- usb20-force-mode: Force the phy to operate in same mode than the USB OTG controller. + It should only be defined if the hardware is not capable correctly + detect the role of USB by using VBUS and ID pin. + This device controls the PHY for both the USB 1.1 OHCI and USB 2.0 OTG controllers on DA8xx SoCs. Consumers of this device should use index 0 for the USB 2.0 phy device and index 1 for the USB 1.1 phy device. -- 2.7.3