From: Peter Chen <peter.chen@nxp.com>
To: <gregkh@linuxfoundation.org>, <stern@rowland.harvard.edu>,
        <ulf.hansson@linaro.org>, <broonie@kernel.org>, <sre@kernel.org>,
        <robh+dt@kernel.org>, <shawnguo@kernel.org>, <rjw@rjwysocki.net>,
        <dbaryshkov@gmail.com>
CC: <heiko@sntech.de>, <linux-arm-kernel@lists.infradead.org>,
        <p.zabel@pengutronix.de>, <devicetree@vger.kernel.org>,
        <pawel.moll@arm.com>, <mark.rutland@arm.com>,
        <linux-usb@vger.kernel.org>, <arnd@arndb.de>, <s.hauer@pengutronix.de>,
        <mail@maciej.szmigiero.name>, <troy.kisky@boundarydevices.com>,
        <festevam@gmail.com>, <oscar@naiandei.net>, <stephen.boyd@linaro.org>,
        <linux-pm@vger.kernel.org>, <stillcompiling@gmail.com>,
        <linux-kernel@vger.kernel.org>, <mka@chromium.org>,
        <vaibhav.hiremath@linaro.org>, <gary.bisson@boundarydevices.com>,
        Peter Chen <peter.chen@nxp.com>
Subject: [PATCH v9 8/8] ARM: dts: imx6q-evi: Fix onboard hub reset line
Date: Tue, 8 Nov 2016 10:51:12 +0800
Message-ID: <1478573472-29516-9-git-send-email-peter.chen@nxp.com>
In-Reply-To: <1478573472-29516-1-git-send-email-peter.chen@nxp.com>
References: <1478573472-29516-1-git-send-email-peter.chen@nxp.com>
MIME-Version: 1.0
Content-Type: text/plain
SpamDiagnosticOutput: 1:99
SpamDiagnosticMetadata: NSPM
X-MS-Exchange-CrossTenant-OriginalArrivalTime: 08 Nov 2016 02:52:23.0521
 (UTC)
X-MS-Exchange-CrossTenant-Id: 5afe0b00-7697-4969-b663-5eab37d5f47e
X-MS-Exchange-CrossTenant-OriginalAttributedTenantConnectingIp: TenantId=5afe0b00-7697-4969-b663-5eab37d5f47e;Ip=[192.88.168.50];Helo=[tx30smr01.am.freescale.net]
X-MS-Exchange-CrossTenant-FromEntityHeader: HybridOnPrem
X-MS-Exchange-Transport-CrossTenantHeadersStamped: CY4PR03MB2743
Sender: linux-kernel-owner@vger.kernel.org
List-ID: <linux-kernel.vger.kernel.org>
X-Mailing-List: linux-kernel@vger.kernel.org
Content-Length: 1837
Lines: 70

From: Joshua Clayton <stillcompiling@gmail.com>

Previously the onboard hub was made to work by treating its
reset gpio as a regulator enable.
Get rid of that kludge now that pwseq has added reset gpio support
Move pin muxing the hub reset pin into the usbh1 group

Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
---
 arch/arm/boot/dts/imx6q-evi.dts | 25 +++++++------------------
 1 file changed, 7 insertions(+), 18 deletions(-)

diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts
index 6de21ff..3277a06 100644
--- a/arch/arm/boot/dts/imx6q-evi.dts
+++ b/arch/arm/boot/dts/imx6q-evi.dts
@@ -54,18 +54,6 @@
 		reg = <0x10000000 0x40000000>;
 	};
 
-	reg_usbh1_vbus: regulator-usbhubreset {
-		compatible = "regulator-fixed";
-		regulator-name = "usbh1_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		enable-active-high;
-		startup-delay-us = <2>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usbh1_hubreset>;
-		gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
-	};
-
 	reg_usb_otg_vbus: regulator-usbotgvbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg_vbus";
@@ -207,12 +195,18 @@
 };
 
 &usbh1 {
-	vbus-supply = <&reg_usbh1_vbus>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbh1>;
 	dr_mode = "host";
 	disable-over-current;
 	status = "okay";
+
+	usb2415host: hub@1 {
+		compatible = "usb424,2513";
+		reg = <1>;
+		reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+		reset-duration-us = <3000>;
+	};
 };
 
 &usbotg {
@@ -471,11 +465,6 @@
 			MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0
 			/* usbh1_b OC */
 			MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
-		>;
-	};
-
-	pinctrl_usbh1_hubreset: usbh1hubresetgrp {
-		fsl,pins = <
 			MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
 		>;
 	};
-- 
2.7.4