Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S933891AbcKILIN (ORCPT ); Wed, 9 Nov 2016 06:08:13 -0500 Received: from mail.linuxfoundation.org ([140.211.169.12]:54994 "EHLO mail.linuxfoundation.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S932859AbcKILII (ORCPT ); Wed, 9 Nov 2016 06:08:08 -0500 From: Greg Kroah-Hartman To: linux-kernel@vger.kernel.org Cc: Greg Kroah-Hartman , stable@vger.kernel.org, Daniel Lezcano , Ulf Hansson , Linus Walleij , Olof Johansson Subject: [PATCH 4.8 073/138] ARM: dts: fix the SD card on the Snowball Date: Wed, 9 Nov 2016 11:45:56 +0100 Message-Id: <20161109102848.189213036@linuxfoundation.org> X-Mailer: git-send-email 2.10.2 In-Reply-To: <20161109102844.808685475@linuxfoundation.org> References: <20161109102844.808685475@linuxfoundation.org> User-Agent: quilt/0.64 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 2683 Lines: 79 4.8-stable review patch. If anyone has any objections, please let me know. ------------------ From: Linus Walleij commit 1b283eea6228880b765bc40fe4e555416437ce58 upstream. This fixes a very annoying regression on the Snowball SD card that has been around for a while. It turns out that the device tree does not configure the direction pins properly, nor sets up the pins for the voltage converter properly at boot. Unless all things are correctly set up, the feedback clock will not work, and makes the driver spew messages in the console (but it works, very slowly): root@Ux500:/ mount /dev/mmcblk0p2 /mnt/ [ 9.953460] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer! [ 9.960296] mmcblk0: error -110 sending status command, retrying [ 9.966461] mmcblk0: error -110 sending status command, retrying [ 9.972534] mmcblk0: error -110 sending status command, aborting Fix this by rectifying the device tree to correspond to that of the Ux500 HREF boards plus the DAT31DIR setting that is unique for the Snowball, and things start working smoothly. Add in the SDR12 and SDR25 modes which this host can do without any problems. I don't know if this has ever been correct, sadly. It works after this patch. Reported-by: Daniel Lezcano Cc: Ulf Hansson Signed-off-by: Linus Walleij Signed-off-by: Olof Johansson Signed-off-by: Greg Kroah-Hartman --- arch/arm/boot/dts/ste-snowball.dts | 15 +++++++++++++-- 1 file changed, 13 insertions(+), 2 deletions(-) --- a/arch/arm/boot/dts/ste-snowball.dts +++ b/arch/arm/boot/dts/ste-snowball.dts @@ -239,14 +239,25 @@ arm,primecell-periphid = <0x10480180>; max-frequency = <100000000>; bus-width = <4>; + cap-sd-highspeed; cap-mmc-highspeed; + sd-uhs-sdr12; + sd-uhs-sdr25; + /* All direction control is used */ + st,sig-dir-cmd; + st,sig-dir-dat0; + st,sig-dir-dat2; + st,sig-dir-dat31; + st,sig-pin-fbclk; + full-pwr-cycle; vmmc-supply = <&ab8500_ldo_aux3_reg>; vqmmc-supply = <&vmmci>; pinctrl-names = "default", "sleep"; pinctrl-0 = <&sdi0_default_mode>; pinctrl-1 = <&sdi0_sleep_mode>; - cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>; // 218 + /* GPIO218 MMC_CD */ + cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>; status = "okay"; }; @@ -549,7 +560,7 @@ /* VMMCI level-shifter enable */ snowball_cfg3 { pins = "GPIO217_AH12"; - ste,config = <&gpio_out_lo>; + ste,config = <&gpio_out_hi>; }; /* VMMCI level-shifter voltage select */ snowball_cfg4 {