Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S932489AbcKVMDY (ORCPT ); Tue, 22 Nov 2016 07:03:24 -0500 Received: from smtp.codeaurora.org ([198.145.29.96]:47482 "EHLO smtp.codeaurora.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S932393AbcKVMDT (ORCPT ); Tue, 22 Nov 2016 07:03:19 -0500 DMARC-Filter: OpenDMARC Filter v1.3.1 smtp.codeaurora.org C12CC61517 Authentication-Results: pdx-caf-mail.web.codeaurora.org; dmarc=none header.from=codeaurora.org Authentication-Results: pdx-caf-mail.web.codeaurora.org; spf=pass smtp.mailfrom=vivek.gautam@codeaurora.org From: Vivek Gautam To: kishon@ti.com, robh+dt@kernel.org, mark.rutland@arm.com, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org Cc: srinivas.kandagatla@linaro.org, sboyd@codeaurora.org, linux-arm-msm@vger.kernel.org, Vivek Gautam Subject: [PATCH v2 4/4] phy: qcom-qmp: new qmp phy driver for qcom-chipsets Date: Tue, 22 Nov 2016 17:32:43 +0530 Message-Id: <1479816163-5260-5-git-send-email-vivek.gautam@codeaurora.org> X-Mailer: git-send-email 1.9.1 In-Reply-To: <1479816163-5260-1-git-send-email-vivek.gautam@codeaurora.org> References: <1479816163-5260-1-git-send-email-vivek.gautam@codeaurora.org> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 39423 Lines: 1222 Qualcomm SOCs have QMP phy controller that provides support to a number of controller, viz. PCIe, UFS, and USB. Add a new driver, based on generic phy framework, for this phy controller. Signed-off-by: Vivek Gautam Tested-by: Srinivas Kandagatla --- Changes since v1: - Fixed missing mutex_unlock() calls in error cases, reported by Julia Lawall. - Selecting CONFIG_RESET_CONTROLLER when this driver is enabled. - Added a boolean property to check if the phy has individual lane reset available. - Took care or EPROBE_DEFER, dev_vdbg() and other minor nits. - Removed references to non-lkml links from commit message. - Moved to use separate iomem resources for each lanes. Tx, Rx and PCS offsets per lane can now come from dt bindings. Comments not addressed in this version: -- Have not addressed Kishon's comment to move phy init table stuff to generic phy calibration bindings. The qmp phy driver has 100 odd register writes (that do phy calibration at much finer level). Incorporating all such into generic phy calibration bindings does not seem possible. One way could have been to add dt-binding for the init table as 'init-sequence'. But that is something strongly disliked by Rob and other dt maintainers. -- Have not addressed Kishon's comments to use phandle label based phy association to the consumer in order to get rid of index based PHY retrieval. This would require adding child nodes, something that we want to avoid. drivers/phy/Kconfig | 9 + drivers/phy/Makefile | 1 + drivers/phy/phy-qcom-qmp.c | 1141 ++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 1151 insertions(+) create mode 100644 drivers/phy/phy-qcom-qmp.c diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig index f1dcec1..8970d9e 100644 --- a/drivers/phy/Kconfig +++ b/drivers/phy/Kconfig @@ -430,6 +430,15 @@ config PHY_STIH407_USB Enable this support to enable the picoPHY device used by USB2 and USB3 controllers on STMicroelectronics STiH407 SoC families. +config PHY_QCOM_QMP + tristate "Qualcomm QMP PHY Driver" + depends on OF && (ARCH_QCOM || COMPILE_TEST) + select GENERIC_PHY + select RESET_CONTROLLER + help + Enable this to support the QMP PHY transceiver that is used + with controllers such as PCIe, UFS, and USB on Qualcomm chips. + config PHY_QCOM_QUSB2 tristate "Qualcomm QUSB2 PHY Driver" depends on OF && (ARCH_QCOM || COMPILE_TEST) diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index dad1682..dbe7731 100644 --- a/drivers/phy/Makefile +++ b/drivers/phy/Makefile @@ -50,6 +50,7 @@ obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o obj-$(CONFIG_PHY_XGENE) += phy-xgene.o obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o obj-$(CONFIG_PHY_QCOM_QUSB2) += phy-qcom-qusb2.o +obj-$(CONFIG_PHY_QCOM_QMP) += phy-qcom-qmp.o obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-14nm.o diff --git a/drivers/phy/phy-qcom-qmp.c b/drivers/phy/phy-qcom-qmp.c new file mode 100644 index 0000000..f85289e --- /dev/null +++ b/drivers/phy/phy-qcom-qmp.c @@ -0,0 +1,1141 @@ +/* + * Copyright (c) 2016, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +/* QMP PHY QSERDES COM registers */ +#define QSERDES_COM_BG_TIMER 0x00c +#define QSERDES_COM_SSC_EN_CENTER 0x010 +#define QSERDES_COM_SSC_ADJ_PER1 0x014 +#define QSERDES_COM_SSC_ADJ_PER2 0x018 +#define QSERDES_COM_SSC_PER1 0x01c +#define QSERDES_COM_SSC_PER2 0x020 +#define QSERDES_COM_SSC_STEP_SIZE1 0x024 +#define QSERDES_COM_SSC_STEP_SIZE2 0x028 +#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN 0x034 +#define QSERDES_COM_CLK_ENABLE1 0x038 +#define QSERDES_COM_SYS_CLK_CTRL 0x03c +#define QSERDES_COM_SYSCLK_BUF_ENABLE 0x040 +#define QSERDES_COM_PLL_IVCO 0x048 +#define QSERDES_COM_LOCK_CMP1_MODE0 0x04c +#define QSERDES_COM_LOCK_CMP2_MODE0 0x050 +#define QSERDES_COM_LOCK_CMP3_MODE0 0x054 +#define QSERDES_COM_LOCK_CMP1_MODE1 0x058 +#define QSERDES_COM_LOCK_CMP2_MODE1 0x05c +#define QSERDES_COM_LOCK_CMP3_MODE1 0x060 +#define QSERDES_COM_BG_TRIM 0x070 +#define QSERDES_COM_CLK_EP_DIV 0x074 +#define QSERDES_COM_CP_CTRL_MODE0 0x078 +#define QSERDES_COM_CP_CTRL_MODE1 0x07c +#define QSERDES_COM_PLL_RCTRL_MODE0 0x084 +#define QSERDES_COM_PLL_RCTRL_MODE1 0x088 +#define QSERDES_COM_PLL_CCTRL_MODE0 0x090 +#define QSERDES_COM_PLL_CCTRL_MODE1 0x094 +#define QSERDES_COM_SYSCLK_EN_SEL 0x0ac +#define QSERDES_COM_RESETSM_CNTRL 0x0b4 +#define QSERDES_COM_RESTRIM_CTRL 0x0bc +#define QSERDES_COM_RESCODE_DIV_NUM 0x0c4 +#define QSERDES_COM_LOCK_CMP_EN 0x0c8 +#define QSERDES_COM_LOCK_CMP_CFG 0x0cc +#define QSERDES_COM_DEC_START_MODE0 0x0d0 +#define QSERDES_COM_DEC_START_MODE1 0x0d4 +#define QSERDES_COM_DIV_FRAC_START1_MODE0 0x0dc +#define QSERDES_COM_DIV_FRAC_START2_MODE0 0x0e0 +#define QSERDES_COM_DIV_FRAC_START3_MODE0 0x0e4 +#define QSERDES_COM_DIV_FRAC_START1_MODE1 0x0e8 +#define QSERDES_COM_DIV_FRAC_START2_MODE1 0x0ec +#define QSERDES_COM_DIV_FRAC_START3_MODE1 0x0f0 +#define QSERDES_COM_INTEGLOOP_GAIN0_MODE0 0x108 +#define QSERDES_COM_INTEGLOOP_GAIN1_MODE0 0x10c +#define QSERDES_COM_INTEGLOOP_GAIN0_MODE1 0x110 +#define QSERDES_COM_INTEGLOOP_GAIN1_MODE1 0x114 +#define QSERDES_COM_VCO_TUNE_CTRL 0x124 +#define QSERDES_COM_VCO_TUNE_MAP 0x128 +#define QSERDES_COM_VCO_TUNE1_MODE0 0x12c +#define QSERDES_COM_VCO_TUNE2_MODE0 0x130 +#define QSERDES_COM_VCO_TUNE1_MODE1 0x134 +#define QSERDES_COM_VCO_TUNE2_MODE1 0x138 +#define QSERDES_COM_VCO_TUNE_TIMER1 0x144 +#define QSERDES_COM_VCO_TUNE_TIMER2 0x148 +#define QSERDES_COM_BG_CTRL 0x170 +#define QSERDES_COM_CLK_SELECT 0x174 +#define QSERDES_COM_HSCLK_SEL 0x178 +#define QSERDES_COM_CORECLK_DIV 0x184 +#define QSERDES_COM_CORE_CLK_EN 0x18c +#define QSERDES_COM_C_READY_STATUS 0x190 +#define QSERDES_COM_CMN_CONFIG 0x194 +#define QSERDES_COM_SVS_MODE_CLK_SEL 0x19c +#define QSERDES_COM_DEBUG_BUS0 0x1a0 +#define QSERDES_COM_DEBUG_BUS1 0x1a4 +#define QSERDES_COM_DEBUG_BUS2 0x1a8 +#define QSERDES_COM_DEBUG_BUS3 0x1ac +#define QSERDES_COM_DEBUG_BUS_SEL 0x1b0 +#define QSERDES_COM_CORECLK_DIV_MODE1 0x1bc + +/* QMP PHY TX registers */ +#define QSERDES_TX_RES_CODE_LANE_OFFSET 0x054 +#define QSERDES_TX_DEBUG_BUS_SEL 0x064 +#define QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN 0x068 +#define QSERDES_TX_LANE_MODE 0x094 +#define QSERDES_TX_RCV_DETECT_LVL_2 0x0ac + +/* QMP PHY RX registers */ +#define QSERDES_RX_UCDR_SO_GAIN_HALF 0x010 +#define QSERDES_RX_UCDR_SO_GAIN 0x01c +#define QSERDES_RX_UCDR_FASTLOCK_FO_GAIN 0x040 +#define QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE 0x048 +#define QSERDES_RX_RX_TERM_BW 0x090 +#define QSERDES_RX_RX_EQ_GAIN1_LSB 0x0c4 +#define QSERDES_RX_RX_EQ_GAIN1_MSB 0x0c8 +#define QSERDES_RX_RX_EQ_GAIN2_LSB 0x0cc +#define QSERDES_RX_RX_EQ_GAIN2_MSB 0x0d0 +#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2 0x0d8 +#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3 0x0dc +#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4 0x0e0 +#define QSERDES_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1 0x108 +#define QSERDES_RX_RX_OFFSET_ADAPTOR_CNTRL2 0x10c +#define QSERDES_RX_SIGDET_ENABLES 0x110 +#define QSERDES_RX_SIGDET_CNTRL 0x114 +#define QSERDES_RX_SIGDET_LVL 0x118 +#define QSERDES_RX_SIGDET_DEGLITCH_CNTRL 0x11c +#define QSERDES_RX_RX_BAND 0x120 +#define QSERDES_RX_RX_INTERFACE_MODE 0x12c + +/* QMP PHY PCS registers */ +#define QPHY_SW_RESET 0x00 +#define QPHY_POWER_DOWN_CONTROL 0x04 +#define QPHY_START_CTRL 0x08 +#define QPHY_TXDEEMPH_M6DB_V0 0x24 +#define QPHY_TXDEEMPH_M3P5DB_V0 0x28 +#define QPHY_ENDPOINT_REFCLK_DRIVE 0x54 +#define QPHY_RX_IDLE_DTCT_CNTRL 0x58 +#define QPHY_POWER_STATE_CONFIG1 0x60 +#define QPHY_POWER_STATE_CONFIG2 0x64 +#define QPHY_POWER_STATE_CONFIG4 0x6c +#define QPHY_LOCK_DETECT_CONFIG1 0x80 +#define QPHY_LOCK_DETECT_CONFIG2 0x84 +#define QPHY_LOCK_DETECT_CONFIG3 0x88 +#define QPHY_PWRUP_RESET_DLY_TIME_AUXCLK 0xa0 +#define QPHY_LP_WAKEUP_DLY_TIME_AUXCLK 0xa4 + +/* PHY_SW_RESET bit */ +#define PHY_SW_RESET BIT(0) +/* PHY_POWER_DOWN_CONTROL */ +#define PHY_SW_PWRDN BIT(0) +#define PHY_REFCLK_DRV_DSBL BIT(1) +/* PHY_START_CONTROL bits */ +#define PHY_SERDES_START BIT(0) +#define PHY_PCS_START BIT(1) +#define PHY_PLL_READY_GATE_EN BIT(3) +/* PHY_PCS_STATUS bit */ +#define MASK_PHYSTATUS BIT(6) +/* PCS_READY_STATUS bit */ +#define MASK_COM_PCS_READY BIT(0) + +#define REFCLK_STABILIZATION_DELAY_US_MIN 1000 +#define REFCLK_STABILIZATION_DELAY_US_MAX 1005 +#define PHY_READY_TIMEOUT_COUNT 10 +#define POWER_DOWN_DELAY_US_MIN 10 +#define POWER_DOWN_DELAY_US_MAX 11 + +#define MAX_PROP_NAME 32 + +struct qmp_phy_init_tbl { + unsigned int reg_offset; + unsigned int cfg_val; + /* + * register part of layout ? + * if yes, then reg_offset gives index in the reg-layout + */ + int in_layout; +}; +#define QCOM_QMP_PHY_INIT_CFG(reg, val) \ + { \ + .reg_offset = reg, \ + .cfg_val = val, \ + } +#define QCOM_QMP_PHY_INIT_CFG_L(reg, val) \ + { \ + .reg_offset = reg, \ + .cfg_val = val, \ + .in_layout = 1, \ + } + +/* set of registers with offsets different per-PHY */ +enum qphy_reg_layout { + /* Common block control registers */ + QPHY_COM_SW_RESET, + QPHY_COM_POWER_DOWN_CONTROL, + QPHY_COM_START_CONTROL, + QPHY_COM_PCS_READY_STATUS, + /* PCS registers */ + QPHY_PLL_LOCK_CHK_DLY_TIME, + QPHY_FLL_CNTRL1, + QPHY_FLL_CNTRL2, + QPHY_FLL_CNT_VAL_L, + QPHY_FLL_CNT_VAL_H_TOL, + QPHY_FLL_MAN_CODE, + QPHY_PCS_READY_STATUS, +}; + +unsigned int pciephy_regs_layout[] = { + [QPHY_COM_SW_RESET] = 0x400, + [QPHY_COM_POWER_DOWN_CONTROL] = 0x404, + [QPHY_COM_START_CONTROL] = 0x408, + [QPHY_COM_PCS_READY_STATUS] = 0x448, + [QPHY_PLL_LOCK_CHK_DLY_TIME] = 0xa8, + [QPHY_FLL_CNTRL1] = 0xc4, + [QPHY_FLL_CNTRL2] = 0xc8, + [QPHY_FLL_CNT_VAL_L] = 0xcc, + [QPHY_FLL_CNT_VAL_H_TOL] = 0xd0, + [QPHY_FLL_MAN_CODE] = 0xd4, + [QPHY_PCS_READY_STATUS] = 0x174, +}; + +unsigned int usb3phy_regs_layout[] = { + [QPHY_FLL_CNTRL1] = 0xc0, + [QPHY_FLL_CNTRL2] = 0xc4, + [QPHY_FLL_CNT_VAL_L] = 0xc8, + [QPHY_FLL_CNT_VAL_H_TOL] = 0xcc, + [QPHY_FLL_MAN_CODE] = 0xd0, + [QPHY_PCS_READY_STATUS] = 0x17c, +}; + +static struct qmp_phy_init_tbl pciephy_serdes_init_tbl[] = { + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x1c), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x33), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x06), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_EN, 0x42), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x00), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER1, 0xff), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER2, 0x1f), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x01), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x01), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x00), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_CORECLK_DIV, 0x0a), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0x09), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x03), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x55), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x55), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x00), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0x1a), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0x0a), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x33), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x02), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_BUF_ENABLE, 0x1f), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x04), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0x0b), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x00), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x01), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER1, 0x31), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER2, 0x01), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x02), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x00), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE1, 0x2f), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE2, 0x19), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_RESCODE_DIV_NUM, 0x15), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0x0f), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0x0f), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_CLK_EP_DIV, 0x19), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x00), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_RESCODE_DIV_NUM, 0x40), +}; + +static struct qmp_phy_init_tbl pciephy_tx_init_tbl[] = { + QCOM_QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45), + QCOM_QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x06), +}; + +static struct qmp_phy_init_tbl pciephy_rx_init_tbl[] = { + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_ENABLES, 0x1c), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x01), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3, 0x00), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4, 0xdb), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_RX_BAND, 0x18), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN, 0x04), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN_HALF, 0x04), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x4b), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x14), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_LVL, 0x19), +}; + +static struct qmp_phy_init_tbl pciephy_pcs_init_tbl[] = { + QCOM_QMP_PHY_INIT_CFG(QPHY_RX_IDLE_DTCT_CNTRL, 0x4c), + QCOM_QMP_PHY_INIT_CFG(QPHY_PWRUP_RESET_DLY_TIME_AUXCLK, 0x00), + QCOM_QMP_PHY_INIT_CFG(QPHY_LP_WAKEUP_DLY_TIME_AUXCLK, 0x01), + + QCOM_QMP_PHY_INIT_CFG_L(QPHY_PLL_LOCK_CHK_DLY_TIME, 0x05), + + QCOM_QMP_PHY_INIT_CFG(QPHY_ENDPOINT_REFCLK_DRIVE, 0x05), + QCOM_QMP_PHY_INIT_CFG(QPHY_POWER_DOWN_CONTROL, 0x02), + QCOM_QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG4, 0x00), + QCOM_QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG1, 0xa3), + QCOM_QMP_PHY_INIT_CFG(QPHY_TXDEEMPH_M3P5DB_V0, 0x0e), +}; + +static struct qmp_phy_init_tbl usb3phy_serdes_init_tbl[] = { + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x14), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x08), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x30), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x06), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x01), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x00), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0x0f), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0x0f), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x04), + /* PLL and Loop filter settings */ + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x55), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x55), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x03), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0x0b), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_CTRL, 0x00), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0x15), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0x34), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x00), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x00), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_CFG, 0x00), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x00), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0x0a), + /* SSC settings */ + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x01), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER1, 0x31), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER2, 0x01), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x00), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x00), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE1, 0xde), + QCOM_QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE2, 0x07), +}; + +static struct qmp_phy_init_tbl usb3phy_tx_init_tbl[] = { + QCOM_QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45), + QCOM_QMP_PHY_INIT_CFG(QSERDES_TX_RCV_DETECT_LVL_2, 0x12), + QCOM_QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x06), +}; + +static struct qmp_phy_init_tbl usb3phy_rx_init_tbl[] = { + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN, 0x04), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x02), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4c), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4, 0xbb), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_CNTRL, 0x03), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_LVL, 0x18), + QCOM_QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x16), +}; + +static struct qmp_phy_init_tbl usb3phy_pcs_init_tbl[] = { + /* FLL settings */ + QCOM_QMP_PHY_INIT_CFG_L(QPHY_FLL_CNTRL2, 0x03), + QCOM_QMP_PHY_INIT_CFG_L(QPHY_FLL_CNTRL1, 0x02), + QCOM_QMP_PHY_INIT_CFG_L(QPHY_FLL_CNT_VAL_L, 0x09), + QCOM_QMP_PHY_INIT_CFG_L(QPHY_FLL_CNT_VAL_H_TOL, 0x42), + QCOM_QMP_PHY_INIT_CFG_L(QPHY_FLL_MAN_CODE, 0x85), + + /* Lock Det settings */ + QCOM_QMP_PHY_INIT_CFG(QPHY_LOCK_DETECT_CONFIG1, 0xd1), + QCOM_QMP_PHY_INIT_CFG(QPHY_LOCK_DETECT_CONFIG2, 0x1f), + QCOM_QMP_PHY_INIT_CFG(QPHY_LOCK_DETECT_CONFIG3, 0x47), + QCOM_QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG2, 0x08), +}; + +/** + * struct qmp_phy_init_cfg:- per-PHY init config. + */ +struct qmp_phy_init_cfg { + /* phy-type - PCIE/UFS/USB */ + unsigned int type; + /* number of lanes provided by phy */ + int nlanes; + + /* Initialization sequence for PHY blocks - Serdes, tx, rx, pcs */ + struct qmp_phy_init_tbl *phy_init_serdes_tbl; + int phy_init_serdes_tbl_sz; + struct qmp_phy_init_tbl *phy_init_tx_tbl; + int phy_init_tx_tbl_sz; + struct qmp_phy_init_tbl *phy_init_rx_tbl; + int phy_init_rx_tbl_sz; + struct qmp_phy_init_tbl *phy_init_pcs_tbl; + int phy_init_pcs_tbl_sz; + + /* array of registers with different offsets */ + unsigned int *regs; + + unsigned int mask_start_ctrl; + unsigned int mask_pwr_dn_ctrl; + /* true, if PHY has a separate PHY_COM_CNTRL block */ + bool has_phy_com_ctrl; + /* true, if PHY has a reset for individual lanes */ + bool has_lane_rst; +}; + +/** + * struct qmp_phy_desc:- per-lane phy-descriptor. + * + * @phy: pointer to generic phy + * @tx: pointer to iomapped memory space for PHY's tx + * @rx: pointer to iomapped memory space for PHY's rx + * @pcs: pointer to iomapped memory space for PHY's pcs + * @pipe_clk: pointer to pipe lock + * @index: lane index + * @qphy: pointer to QMP phy to which this lane belongs + * @lane_rst: pointer to lane's reset controller + */ +struct qmp_phy_desc { + struct phy *phy; + void __iomem *tx; + void __iomem *rx; + void __iomem *pcs; + struct clk *pipe_clk; + unsigned int index; + struct qcom_qmp_phy *qphy; + struct reset_control *lane_rst; +}; + +/** + * struct qcom_qmp_phy:- structure holding QMP PHY attributes. + * + * @dev: pointer to device + * @serdes: pointer to iomapped memory space for phy's serdes + * + * @aux_clk: pointer to phy core clock + * @cfg_ahb_clk: pointer to AHB2PHY interface clock + * @ref_clk: pointer to reference clock + * @ref_clk_src: pointer to source to reference clock + * + * @vdda_phy: vdd supply to the phy core block + * @vdda_pll: 1.8V vdd supply to ref_clk block + * @vddp_ref_clk: vdd supply to specific ref_clk block (Optional) + * + * @phy_rst: Pointer to phy reset control + * @phycom_rst: Pointer to phy common reset control + * @phycfg_rst: Pointer to phy ahb cfg reset control (Optional) + * + * @cfg: pointer to init config for each phys + * @phys: array of pointer to per-lane phy descriptors + * @phy_mutex: mutex lock for PHY common block initialization + * @init_count: Phy common block initialization count + */ +struct qcom_qmp_phy { + struct device *dev; + void __iomem *serdes; + + struct clk *aux_clk; + struct clk *cfg_ahb_clk; + struct clk *ref_clk; + struct clk *ref_clk_src; + + struct regulator *vdda_phy; + struct regulator *vdda_pll; + struct regulator *vddp_ref_clk; + + struct reset_control *phy_rst; + struct reset_control *phycom_rst; + struct reset_control *phycfg_rst; + + const struct qmp_phy_init_cfg *cfg; + struct qmp_phy_desc **phys; + + struct mutex phy_mutex; + int init_count; +}; + +static inline void qphy_setbits(void __iomem *reg, u32 val) +{ + u32 reg_val; + + reg_val = readl_relaxed(reg); + reg_val |= val; + writel_relaxed(reg_val, reg); +} + +static inline void qphy_clrbits(void __iomem *reg, u32 val) +{ + u32 reg_val; + + reg_val = readl_relaxed(reg); + reg_val &= ~val; + writel_relaxed(reg_val, reg); +} + +const struct qmp_phy_init_cfg msm8996_pciephy_init_cfg = { + .type = PHY_TYPE_PCIE, + .nlanes = 3, + + .phy_init_serdes_tbl = pciephy_serdes_init_tbl, + .phy_init_serdes_tbl_sz = ARRAY_SIZE(pciephy_serdes_init_tbl), + .phy_init_tx_tbl = pciephy_tx_init_tbl, + .phy_init_tx_tbl_sz = ARRAY_SIZE(pciephy_tx_init_tbl), + .phy_init_rx_tbl = pciephy_rx_init_tbl, + .phy_init_rx_tbl_sz = ARRAY_SIZE(pciephy_rx_init_tbl), + .phy_init_pcs_tbl = pciephy_pcs_init_tbl, + .phy_init_pcs_tbl_sz = ARRAY_SIZE(pciephy_pcs_init_tbl), + .regs = pciephy_regs_layout, + .mask_start_ctrl = (PHY_PCS_START | PHY_PLL_READY_GATE_EN), + .mask_pwr_dn_ctrl = (PHY_SW_PWRDN | PHY_REFCLK_DRV_DSBL), + + .has_phy_com_ctrl = true, + .has_lane_rst = true, +}; + +const struct qmp_phy_init_cfg msm8996_usb3phy_init_cfg = { + .type = PHY_TYPE_USB3, + .nlanes = 1, + + .phy_init_serdes_tbl = usb3phy_serdes_init_tbl, + .phy_init_serdes_tbl_sz = ARRAY_SIZE(usb3phy_serdes_init_tbl), + .phy_init_tx_tbl = usb3phy_tx_init_tbl, + .phy_init_tx_tbl_sz = ARRAY_SIZE(usb3phy_tx_init_tbl), + .phy_init_rx_tbl = usb3phy_rx_init_tbl, + .phy_init_rx_tbl_sz = ARRAY_SIZE(usb3phy_rx_init_tbl), + .phy_init_pcs_tbl = usb3phy_pcs_init_tbl, + .phy_init_pcs_tbl_sz = ARRAY_SIZE(usb3phy_pcs_init_tbl), + .regs = usb3phy_regs_layout, + .mask_start_ctrl = (PHY_SERDES_START | PHY_PCS_START), + .mask_pwr_dn_ctrl = PHY_SW_PWRDN, +}; + +static void qcom_qmp_phy_configure(void __iomem *base, + unsigned int *regs_layout, + struct qmp_phy_init_tbl init_tbl[], + int init_tbl_sz) +{ + int i; + + for (i = 0; i < init_tbl_sz; i++) { + if (init_tbl[i].in_layout) + writel_relaxed(init_tbl[i].cfg_val, + base + regs_layout[init_tbl[i].reg_offset]); + else + writel_relaxed(init_tbl[i].cfg_val, + base + init_tbl[i].reg_offset); + } + + /* flush buffered writes */ + mb(); +} + +static int qcom_qmp_phy_poweron(struct phy *phy) +{ + struct qmp_phy_desc *phydesc = phy_get_drvdata(phy); + struct qcom_qmp_phy *qphy = phydesc->qphy; + int ret; + + dev_vdbg(&phy->dev, "Powering on QMP phy\n"); + + ret = regulator_enable(qphy->vdda_phy); + if (ret) { + dev_err(qphy->dev, "%s: vdda-phy enable failed, err=%d\n", + __func__, ret); + return ret; + } + + ret = regulator_enable(qphy->vdda_pll); + if (ret) { + dev_err(qphy->dev, "%s: vdda-pll enable failed, err=%d\n", + __func__, ret); + goto err_vdda_pll; + } + + if (qphy->vddp_ref_clk) { + ret = regulator_enable(qphy->vddp_ref_clk); + if (ret) { + dev_err(qphy->dev, "%s: vdda-ref-clk enable failed, err=%d\n", + __func__, ret); + goto err_vddp_refclk; + } + } + + clk_prepare_enable(qphy->ref_clk_src); + clk_prepare_enable(qphy->ref_clk); + clk_prepare_enable(phydesc->pipe_clk); + + return 0; + +err_vddp_refclk: + regulator_disable(qphy->vdda_pll); +err_vdda_pll: + regulator_disable(qphy->vdda_phy); + return ret; +} + +static int qcom_qmp_phy_poweroff(struct phy *phy) +{ + struct qmp_phy_desc *phydesc = phy_get_drvdata(phy); + struct qcom_qmp_phy *qphy = phydesc->qphy; + + clk_disable_unprepare(qphy->ref_clk_src); + clk_disable_unprepare(qphy->ref_clk); + clk_disable_unprepare(phydesc->pipe_clk); + + if (qphy->vddp_ref_clk) + regulator_disable(qphy->vddp_ref_clk); + + regulator_disable(qphy->vdda_pll); + regulator_disable(qphy->vdda_phy); + + return 0; +} + +static int qcom_qmp_phy_is_ready(struct qcom_qmp_phy *qphy, + void __iomem *pcs_status, u32 mask) +{ + unsigned int init_timeout; + + init_timeout = PHY_READY_TIMEOUT_COUNT; + do { + if (readl_relaxed(pcs_status) & mask) + break; + + usleep_range(REFCLK_STABILIZATION_DELAY_US_MIN, + REFCLK_STABILIZATION_DELAY_US_MAX); + } while (--init_timeout); + + if (!init_timeout) + return -EBUSY; + + return 0; +} + +static int qcom_qmp_phy_com_init(struct qcom_qmp_phy *qphy) +{ + const struct qmp_phy_init_cfg *cfg = qphy->cfg; + void __iomem *serdes = qphy->serdes; + int ret; + + mutex_lock(&qphy->phy_mutex); + if (qphy->init_count++) { + mutex_unlock(&qphy->phy_mutex); + return 0; + } + + ret = reset_control_deassert(qphy->phy_rst); + if (ret) { + dev_err(qphy->dev, "phy reset deassert failed\n"); + goto err; + } + + ret = reset_control_deassert(qphy->phycom_rst); + if (ret) { + dev_err(qphy->dev, "common reset deassert failed\n"); + goto err_phycom_rst; + } + + if (qphy->phycfg_rst) { + ret = reset_control_deassert(qphy->phycfg_rst); + if (ret) { + dev_err(qphy->dev, "common reset deassert failed\n"); + goto err_phycfg_rst; + } + } + + if (cfg->has_phy_com_ctrl) { + qphy_setbits(serdes + cfg->regs[QPHY_COM_POWER_DOWN_CONTROL], + PHY_SW_PWRDN); + /* Make sure that above write is completed */ + mb(); + } + + /* Serdes configuration */ + qcom_qmp_phy_configure(serdes, cfg->regs, cfg->phy_init_serdes_tbl, + cfg->phy_init_serdes_tbl_sz); + + if (cfg->has_phy_com_ctrl) { + qphy_clrbits(serdes + cfg->regs[QPHY_COM_SW_RESET], + PHY_SW_RESET); + qphy_setbits(serdes + cfg->regs[QPHY_COM_START_CONTROL], + PHY_SERDES_START | PHY_PCS_START); + /* Make sure that above write is completed */ + mb(); + + ret = qcom_qmp_phy_is_ready(qphy, serdes + + cfg->regs[QPHY_COM_PCS_READY_STATUS], + MASK_COM_PCS_READY); + if (ret) { + dev_err(qphy->dev, + "common control block init timed-out\n"); + goto err_phy_comctrl; + } + } + + mutex_unlock(&qphy->phy_mutex); + + return 0; + +err_phy_comctrl: + if (qphy->phycfg_rst) + reset_control_assert(qphy->phycfg_rst); +err_phycfg_rst: + reset_control_assert(qphy->phycom_rst); +err_phycom_rst: + reset_control_assert(qphy->phy_rst); +err: + mutex_unlock(&qphy->phy_mutex); + return ret; +} + +static int qcom_qmp_phy_com_exit(struct qcom_qmp_phy *qphy) +{ + const struct qmp_phy_init_cfg *cfg = qphy->cfg; + void __iomem *serdes = qphy->serdes; + + mutex_lock(&qphy->phy_mutex); + if (--qphy->init_count) { + mutex_unlock(&qphy->phy_mutex); + return 0; + } + + if (cfg->has_phy_com_ctrl) { + qphy_setbits(serdes + cfg->regs[QPHY_COM_START_CONTROL], + PHY_SERDES_START | PHY_PCS_START); + qphy_clrbits(serdes + cfg->regs[QPHY_COM_SW_RESET], + PHY_SW_RESET); + qphy_setbits(serdes + cfg->regs[QPHY_COM_POWER_DOWN_CONTROL], + PHY_SW_PWRDN); + + /* Make sure that above writes are completed */ + mb(); + } + + reset_control_assert(qphy->phy_rst); + reset_control_assert(qphy->phycom_rst); + if (qphy->phycfg_rst) + reset_control_assert(qphy->phycfg_rst); + + mutex_unlock(&qphy->phy_mutex); + + return 0; +} + +/* PHY Initialization */ +static int qcom_qmp_phy_init(struct phy *phy) +{ + struct qmp_phy_desc *phydesc = phy_get_drvdata(phy); + struct qcom_qmp_phy *qphy = phydesc->qphy; + const struct qmp_phy_init_cfg *cfg = qphy->cfg; + void __iomem *tx = phydesc->tx; + void __iomem *rx = phydesc->rx; + void __iomem *pcs = phydesc->pcs; + int ret; + + dev_vdbg(qphy->dev, "Initializing QMP phy\n"); + + /* enable interface clocks to program phy */ + clk_prepare_enable(qphy->aux_clk); + clk_prepare_enable(qphy->cfg_ahb_clk); + + ret = qcom_qmp_phy_com_init(qphy); + if (ret) + goto err; + + if (phydesc->lane_rst) { + ret = reset_control_deassert(phydesc->lane_rst); + if (ret) { + dev_err(qphy->dev, "lane<%d> reset deassert failed\n", + phydesc->index); + goto err_lane_rst; + } + } + + /* Tx, Rx, and PCS configurations */ + qcom_qmp_phy_configure(tx, cfg->regs, cfg->phy_init_tx_tbl, + cfg->phy_init_tx_tbl_sz); + qcom_qmp_phy_configure(rx, cfg->regs, cfg->phy_init_rx_tbl, + cfg->phy_init_rx_tbl_sz); + qcom_qmp_phy_configure(pcs, cfg->regs, cfg->phy_init_pcs_tbl, + cfg->phy_init_pcs_tbl_sz); + + /* + * Pull out PHY from POWER DOWN state: + * This is active low enable signal to power-down PHY. + */ + qphy_setbits(pcs + QPHY_POWER_DOWN_CONTROL, cfg->mask_pwr_dn_ctrl); + /* XXX: 10 us delay; given in PCIE phy programming guide only */ + usleep_range(POWER_DOWN_DELAY_US_MIN, POWER_DOWN_DELAY_US_MAX); + + /* start SerDes and Phy-Coding-Sublayer */ + qphy_setbits(pcs + QPHY_START_CTRL, cfg->mask_start_ctrl); + + /* Pull PHY out of reset state */ + qphy_clrbits(pcs + QPHY_SW_RESET, PHY_SW_RESET); + /* Make sure that above writes are completed */ + mb(); + + ret = qcom_qmp_phy_is_ready(qphy, pcs + + cfg->regs[QPHY_PCS_READY_STATUS], + MASK_PHYSTATUS); + if (ret) { + dev_err(qphy->dev, "phy initialization timed-out\n"); + goto err_pcs_ready; + } + + return 0; + +err_pcs_ready: + if (phydesc->lane_rst) + reset_control_assert(phydesc->lane_rst); +err_lane_rst: + qcom_qmp_phy_com_exit(qphy); +err: + clk_disable_unprepare(qphy->cfg_ahb_clk); + clk_disable_unprepare(qphy->aux_clk); + return ret; +} + +static int qcom_qmp_phy_exit(struct phy *phy) +{ + struct qmp_phy_desc *phydesc = phy_get_drvdata(phy); + struct qcom_qmp_phy *qphy = phydesc->qphy; + const struct qmp_phy_init_cfg *cfg = qphy->cfg; + + /* PHY reset */ + qphy_setbits(phydesc->pcs + QPHY_SW_RESET, PHY_SW_RESET); + + /* stop SerDes and Phy-Coding-Sublayer */ + qphy_clrbits(phydesc->pcs + QPHY_START_CTRL, cfg->mask_start_ctrl); + + /* Put PHY into POWER DOWN state: active low */ + qphy_clrbits(phydesc->pcs + QPHY_POWER_DOWN_CONTROL, + cfg->mask_pwr_dn_ctrl); + + /* Make sure that above writes are completed */ + mb(); + + if (phydesc->lane_rst) + reset_control_assert(phydesc->lane_rst); + + qcom_qmp_phy_com_exit(qphy); + + clk_disable_unprepare(qphy->aux_clk); + clk_disable_unprepare(qphy->cfg_ahb_clk); + + return 0; +} + + +static int qcom_qmp_phy_regulator_init(struct device *dev) +{ + struct qcom_qmp_phy *qphy = dev_get_drvdata(dev); + int ret; + + qphy->vdda_phy = devm_regulator_get(dev, "vdda-phy"); + if (IS_ERR(qphy->vdda_phy)) { + ret = PTR_ERR(qphy->vdda_phy); + if (ret != -EPROBE_DEFER) + dev_err(dev, "failed to get vdda-phy, %d\n", ret); + return ret; + } + + qphy->vdda_pll = devm_regulator_get(dev, "vdda-pll"); + if (IS_ERR(qphy->vdda_pll)) { + ret = PTR_ERR(qphy->vdda_pll); + if (ret != -EPROBE_DEFER) + dev_err(dev, "failed to get vdda-pll, %d\n", ret); + return ret; + } + + /* optional regulator */ + qphy->vddp_ref_clk = devm_regulator_get(dev, "vddp-ref-clk"); + if (IS_ERR(qphy->vddp_ref_clk)) { + ret = PTR_ERR(qphy->vddp_ref_clk); + if (ret != -EPROBE_DEFER) { + dev_dbg(dev, "failed to get vddp-ref-clk, %d\n", ret); + qphy->vddp_ref_clk = NULL; + } else { + return ret; + } + } + + return 0; +} + +static int qcom_qmp_phy_clk_init(struct device *dev) +{ + struct qcom_qmp_phy *qphy = dev_get_drvdata(dev); + int ret; + + qphy->aux_clk = devm_clk_get(dev, "aux"); + if (IS_ERR(qphy->aux_clk)) { + ret = PTR_ERR(qphy->aux_clk); + if (ret != -EPROBE_DEFER) + dev_err(dev, "failed to get aux_clk\n"); + return ret; + } + + qphy->cfg_ahb_clk = devm_clk_get(dev, "cfg_ahb"); + if (IS_ERR(qphy->cfg_ahb_clk)) { + ret = PTR_ERR(qphy->cfg_ahb_clk); + if (ret != -EPROBE_DEFER) + dev_err(dev, "failed to get cfg_ahb_clk\n"); + return ret; + } + + qphy->ref_clk_src = devm_clk_get(dev, "ref_clk_src"); + if (IS_ERR(qphy->ref_clk_src)) { + ret = PTR_ERR(qphy->ref_clk_src); + if (ret != -EPROBE_DEFER) + dev_err(dev, "failed to get ref_clk_src\n"); + return ret; + } + + qphy->ref_clk = devm_clk_get(dev, "ref_clk"); + if (IS_ERR(qphy->ref_clk)) { + ret = PTR_ERR(qphy->ref_clk); + if (ret != -EPROBE_DEFER) + dev_err(dev, "failed to get ref_clk\n"); + return ret; + } + + return 0; +} + +static struct phy *qcom_qmp_phy_xlate(struct device *dev, + struct of_phandle_args *args) +{ + struct qcom_qmp_phy *qphy = dev_get_drvdata(dev); + int i; + + if (WARN_ON(args->args[0] >= qphy->cfg->nlanes)) + return ERR_PTR(-ENODEV); + + for (i = 0; i < qphy->cfg->nlanes; i++) { + if (qphy->phys[i]->index == args->args[0]) + break; + } + + if (i == qphy->cfg->nlanes) + return ERR_PTR(-ENODEV); + + return qphy->phys[i]->phy; +} + +static const struct phy_ops qcom_qmp_phy_gen_ops = { + .init = qcom_qmp_phy_init, + .exit = qcom_qmp_phy_exit, + .power_on = qcom_qmp_phy_poweron, + .power_off = qcom_qmp_phy_poweroff, + .owner = THIS_MODULE, +}; + +static const struct of_device_id qcom_qmp_phy_of_match_table[] = { + { + .compatible = "qcom,msm8996-qmp-pcie-phy", + .data = &msm8996_pciephy_init_cfg, + }, { + .compatible = "qcom,msm8996-qmp-usb3-phy", + .data = &msm8996_usb3phy_init_cfg, + }, + { }, +}; +MODULE_DEVICE_TABLE(of, qcom_qmp_phy_of_match_table); + +static int qcom_qmp_phy_probe(struct platform_device *pdev) +{ + struct qcom_qmp_phy *qphy; + struct device *dev = &pdev->dev; + struct phy_provider *phy_provider; + struct resource *res; + const struct of_device_id *match; + void __iomem *base; + int ret = 0; + int id; + + qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL); + if (!qphy) + return -ENOMEM; + + qphy->dev = dev; + dev_set_drvdata(dev, qphy); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + base = devm_ioremap_resource(dev, res); + if (IS_ERR(base)) + return PTR_ERR(base); + + /* per PHY serdes; usually located at base address */ + qphy->serdes = base; + + mutex_init(&qphy->phy_mutex); + + /* Get the specific init parameters of QMP phy */ + match = of_match_node(qcom_qmp_phy_of_match_table, dev->of_node); + qphy->cfg = match->data; + + ret = qcom_qmp_phy_clk_init(dev); + if (ret) { + dev_err(dev, "clock init failed\n"); + return ret; + } + + ret = qcom_qmp_phy_regulator_init(dev); + if (ret) { + dev_err(dev, "regulator init failed\n"); + return ret; + } + + qphy->phy_rst = devm_reset_control_get(dev, "phy"); + if (IS_ERR(qphy->phy_rst)) { + dev_err(dev, "failed to get phy core reset\n"); + return PTR_ERR(qphy->phy_rst); + } + + qphy->phycom_rst = devm_reset_control_get(dev, "common"); + if (IS_ERR(qphy->phycom_rst)) { + dev_err(dev, "failed to get phy common reset\n"); + return PTR_ERR(qphy->phycom_rst); + } + + qphy->phycfg_rst = devm_reset_control_get(dev, "cfg"); + if (IS_ERR(qphy->phycfg_rst)) { + dev_dbg(dev, "failed to get phy ahb cfg reset\n"); + qphy->phycfg_rst = NULL; + } + + qphy->phys = devm_kcalloc(dev, qphy->cfg->nlanes, + sizeof(*qphy->phys), GFP_KERNEL); + if (!qphy->phys) + return -ENOMEM; + + for (id = 0; id < qphy->cfg->nlanes; id++) { + struct phy *generic_phy; + struct qmp_phy_desc *phy_desc; + char prop_name[MAX_PROP_NAME]; + unsigned int lane_offsets[3]; + + /* mem resources from index 1 to N for N number of lanes */ + res = platform_get_resource(pdev, IORESOURCE_MEM, id + 1); + base = devm_ioremap_resource(dev, res); + if (IS_ERR(base)) + return PTR_ERR(base); + + phy_desc = devm_kzalloc(dev, sizeof(*phy_desc), GFP_KERNEL); + if (!phy_desc) + return -ENOMEM; + + /* + * read offsets to Tx, Rx, and PCS blocks into a u32 array: + * ------------------------------------ + * | tx offset | rx offset | pcs offset | + * ------------------------------------ + */ + ret = of_property_read_u32_array(dev->of_node, "lane-offsets", + lane_offsets, 3); + if (ret) { + dev_err(dev, + "failed to get tx/rx/pcs offsets for lane%d\n", + id); + return ret; + } + + phy_desc->tx = base + lane_offsets[0]; + phy_desc->rx = base + lane_offsets[1]; + phy_desc->pcs = base + lane_offsets[2]; + + /* + * Get PHY's Pipe clock, if any; USB3 and PCIe are PIPE3 + * based phys, so they essentially have pipe clock. So, + * we return error in case phy is USB3 or PIPE type. + * Otherwise, we initialize pipe clock to NULL for + * all phys that don't need this. + */ + memset(&prop_name, 0, sizeof(prop_name)); + snprintf(prop_name, MAX_PROP_NAME, "pipe%d", id); + phy_desc->pipe_clk = devm_clk_get(dev, prop_name); + if (IS_ERR(phy_desc->pipe_clk)) { + if (qphy->cfg->type == PHY_TYPE_PCIE || + qphy->cfg->type == PHY_TYPE_USB3) { + ret = PTR_ERR(phy_desc->pipe_clk); + if (ret != -EPROBE_DEFER) + dev_err(dev, + "failed to get lane%d pipe_clk\n", id); + return ret; + } else { + phy_desc->pipe_clk = NULL; + } + } + + /* Get lane reset, if any */ + if (qphy->cfg->has_lane_rst) { + memset(&prop_name, 0, sizeof(prop_name)); + snprintf(prop_name, MAX_PROP_NAME, "lane%d", id); + phy_desc->lane_rst = devm_reset_control_get(dev, + prop_name); + if (IS_ERR(phy_desc->lane_rst)) { + dev_err(dev, "failed to get lane%d reset\n", + id); + return PTR_ERR(phy_desc->lane_rst); + } + } + + generic_phy = devm_phy_create(dev, NULL, &qcom_qmp_phy_gen_ops); + if (IS_ERR(generic_phy)) { + ret = PTR_ERR(generic_phy); + dev_err(dev, "failed to create qphy %d\n", ret); + return ret; + } + + phy_desc->phy = generic_phy; + phy_desc->index = id; + phy_desc->qphy = qphy; + phy_set_drvdata(generic_phy, phy_desc); + qphy->phys[id] = phy_desc; + } + + phy_provider = devm_of_phy_provider_register(dev, qcom_qmp_phy_xlate); + if (IS_ERR(phy_provider)) { + ret = PTR_ERR(phy_provider); + dev_err(dev, "failed to register qphy %d\n", ret); + } + + return ret; +} + +static struct platform_driver qcom_qmp_phy_driver = { + .probe = qcom_qmp_phy_probe, + .driver = { + .name = "qcom_qmp_phy", + .of_match_table = of_match_ptr(qcom_qmp_phy_of_match_table), + }, +}; + +module_platform_driver(qcom_qmp_phy_driver); + +MODULE_AUTHOR("Vivek Gautam "); +MODULE_DESCRIPTION("Qualcomm QMP PHY driver"); +MODULE_LICENSE("GPL v2"); -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project