Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1755288AbcKYPqJ (ORCPT ); Fri, 25 Nov 2016 10:46:09 -0500 Received: from smtpfb1-g21.free.fr ([212.27.42.9]:46545 "EHLO smtpfb1-g21.free.fr" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1754935AbcKYPqD (ORCPT ); Fri, 25 Nov 2016 10:46:03 -0500 Subject: Re: Tearing down DMA transfer setup after DMA client has finished To: Mans Rullgard Cc: Vinod Koul , dmaengine@vger.kernel.org, Linus Walleij , Dan Williams , LKML , Linux ARM , Jon Mason , Mark Brown , Lars-Peter Clausen , Lee Jones , Laurent Pinchart , Arnd Bergmann , Maxime Ripard , Dave Jiang , Peter Ujfalusi , Bartlomiej Zolnierkiewicz References: <58356EA8.2010806@free.fr> <20161125045549.GC2698@localhost> <092f44ee-4560-be17-25f7-00948dba3cfa@free.fr> <28bb9925-d0d7-9261-27fb-aa79345a19f1@free.fr> From: Mason Message-ID: Date: Fri, 25 Nov 2016 16:35:17 +0100 User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:49.0) Gecko/20100101 Firefox/49.0 SeaMonkey/2.46 MIME-Version: 1.0 In-Reply-To: Content-Type: text/plain; charset=ISO-8859-15 Content-Transfer-Encoding: 8bit Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 3696 Lines: 95 On 25/11/2016 15:37, M?ns Rullg?rd wrote: > Mason writes: > >> On 25/11/2016 14:11, M?ns Rullg?rd wrote: >> >>> Mason writes: >>> >>>> It seems there is a disconnect between what Linux expects - an IRQ >>>> when the transfer is complete - and the quirks of this HW :-( >>>> >>>> On this system, there are MBUS "agents" connected via a "switch box". >>>> An agent fires an IRQ when it has dealt with its *half* of the transfer. >>>> >>>> SOURCE_AGENT <---> SBOX <---> DESTINATION_AGENT >>>> >>>> Here are the steps for a transfer, in the general case: >>>> >>>> 1) setup the sbox to connect SOURCE TO DEST >>>> 2) configure source to send N bytes >>>> 3) configure dest to receive N bytes >>>> >>>> When SOURCE_AGENT has sent N bytes, it fires an IRQ >>>> When DEST_AGENT has received N bytes, it fires an IRQ >>>> The sbox connection can be torn down only when the destination >>>> agent has received all bytes. >>>> (And the twist is that some agents do not have an IRQ line.) >>>> >>>> The system provides 3 RAM-to-sbox agents (read channels) >>>> and 3 sbox-to-RAM agents (write channels). >>>> >>>> The NAND Flash controller read and write agents do not have >>>> IRQ lines. >>>> >>>> So for a NAND-to-memory transfer (read from device) >>>> - nothing happens when the NFC has finished sending N bytes to the sbox >>>> - the write channel fires an IRQ when it has received N bytes >>>> >>>> In that case, one IRQ fires when the transfer is complete, >>>> like Linux expects. >>>> >>>> For a memory-to-NAND transfer (write to device) >>>> - the read channel fires an IRQ when it has sent N bytes >>>> - the NFC driver is supposed to poll the NFC to determine >>>> when the controller has finished writing N bytes >>>> >>>> In that case, the IRQ does not indicate that the transfer >>>> is complete, merely that the sending half has finished >>>> its part. >>> >>> When does your NAND controller signal completion? When it has received >>> the DMA data, or only when it has finished the actual write operation? >> >> The NAND controller provides a STATUS register. >> Bit 31 is the CMD_READY bit. >> This bit goes to 0 when the controller is busy, and to 1 >> when the controller is ready to accept the next command. >> >> The NFC driver is doing: >> >> res = wait_for_completion_timeout(&tx_done, HZ); >> if (res > 0) >> err = readl_poll_timeout(addr, val, val & CMD_READY, 0, 1000); >> >> So basically, sleep until the memory agent IRQ falls, >> then spin until the controller is idle. > > This doesn't answer my question. Waiting for the entire operation to > finish isn't necessary. The dma driver only needs to wait until all the > data has been received by the nand controller, not until the controller > is completely finished with the command. Does the nand controller > provide an indication for completion of the dma independently of the > progress of the write command? The dma glue Sigma added to the > Designware sata controller does this. I called the HW dev. He told me the NFC block does not have buffers to store the incoming data; so they remain in the MBUS FIFOs until the NFC consumes them, i.e. when it has finished writing them to a NAND chip, which could take a "long time" when writing to a slow chip. So the answer to your question is: "the NAND controller signals completion only when it has finished the actual write operation." >> Did you see that adding a 10 ?s delay at the start of >> tangox_dma_pchan_detach() makes the system no longer >> fail (passes an mtd_speedtest). > > Yes, but maybe that's much longer than is actually necessary. I could instrument my spin loop to record how long we had to wait between the IRQ and CMD_READY. Regards.