Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1752608AbcL1XDa (ORCPT ); Wed, 28 Dec 2016 18:03:30 -0500 Received: from mail-pg0-f44.google.com ([74.125.83.44]:36059 "EHLO mail-pg0-f44.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752105AbcL1W5S (ORCPT ); Wed, 28 Dec 2016 17:57:18 -0500 From: Stephen Boyd To: linux-usb@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org, Andy Gross , Bjorn Andersson , Neil Armstrong , Arnd Bergmann , Felipe Balbi , Peter Chen , Greg Kroah-Hartman , devicetree@vger.kernel.org Subject: [PATCH v6 03/25] usb: ulpi: Support device discovery via DT Date: Wed, 28 Dec 2016 14:56:49 -0800 Message-Id: <20161228225711.698-4-stephen.boyd@linaro.org> X-Mailer: git-send-email 2.10.0.297.gf6727b0 In-Reply-To: <20161228225711.698-1-stephen.boyd@linaro.org> References: <20161228225711.698-1-stephen.boyd@linaro.org> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 7180 Lines: 227 The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman Acked-by: Heikki Krogerus Cc: Acked-by: Rob Herring Signed-off-by: Stephen Boyd --- Documentation/devicetree/bindings/usb/ulpi.txt | 20 +++++++ drivers/usb/common/ulpi.c | 79 ++++++++++++++++++++++++-- 2 files changed, 93 insertions(+), 6 deletions(-) create mode 100644 Documentation/devicetree/bindings/usb/ulpi.txt diff --git a/Documentation/devicetree/bindings/usb/ulpi.txt b/Documentation/devicetree/bindings/usb/ulpi.txt new file mode 100644 index 000000000000..ca179dc4bd50 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ulpi.txt @@ -0,0 +1,20 @@ +ULPI bus binding +---------------- + +Phys that are behind a ULPI connection can be described with the following +binding. The host controller shall have a "ulpi" named node as a child, and +that node shall have one enabled node underneath it representing the ulpi +device on the bus. + +EXAMPLE +------- + +usb { + compatible = "vendor,usb-controller"; + + ulpi { + phy { + compatible = "vendor,phy"; + }; + }; +}; diff --git a/drivers/usb/common/ulpi.c b/drivers/usb/common/ulpi.c index 8b317702d761..c9480d77810c 100644 --- a/drivers/usb/common/ulpi.c +++ b/drivers/usb/common/ulpi.c @@ -16,6 +16,9 @@ #include #include #include +#include +#include +#include /* -------------------------------------------------------------------------- */ @@ -39,6 +42,10 @@ static int ulpi_match(struct device *dev, struct device_driver *driver) struct ulpi *ulpi = to_ulpi_dev(dev); const struct ulpi_device_id *id; + /* Some ULPI devices don't have a vendor id so rely on OF match */ + if (ulpi->id.vendor == 0) + return of_driver_match_device(dev, driver); + for (id = drv->id_table; id->vendor; id++) if (id->vendor == ulpi->id.vendor && id->product == ulpi->id.product) @@ -50,6 +57,11 @@ static int ulpi_match(struct device *dev, struct device_driver *driver) static int ulpi_uevent(struct device *dev, struct kobj_uevent_env *env) { struct ulpi *ulpi = to_ulpi_dev(dev); + int ret; + + ret = of_device_uevent_modalias(dev, env); + if (ret != -ENODEV) + return ret; if (add_uevent_var(env, "MODALIAS=ulpi:v%04xp%04x", ulpi->id.vendor, ulpi->id.product)) @@ -60,6 +72,11 @@ static int ulpi_uevent(struct device *dev, struct kobj_uevent_env *env) static int ulpi_probe(struct device *dev) { struct ulpi_driver *drv = to_ulpi_driver(dev->driver); + int ret; + + ret = of_clk_set_defaults(dev->of_node, false); + if (ret < 0) + return ret; return drv->probe(to_ulpi_dev(dev)); } @@ -87,8 +104,13 @@ static struct bus_type ulpi_bus = { static ssize_t modalias_show(struct device *dev, struct device_attribute *attr, char *buf) { + int len; struct ulpi *ulpi = to_ulpi_dev(dev); + len = of_device_get_modalias(dev, buf, PAGE_SIZE - 1); + if (len != -ENODEV) + return len; + return sprintf(buf, "ulpi:v%04xp%04x\n", ulpi->id.vendor, ulpi->id.product); } @@ -153,23 +175,45 @@ EXPORT_SYMBOL_GPL(ulpi_unregister_driver); /* -------------------------------------------------------------------------- */ -static int ulpi_register(struct device *dev, struct ulpi *ulpi) +static int ulpi_of_register(struct ulpi *ulpi) { - int ret; + struct device_node *np = NULL, *child; + struct device *parent; + + /* Find a ulpi bus underneath the parent or the grandparent */ + parent = ulpi->dev.parent; + if (parent->of_node) + np = of_find_node_by_name(parent->of_node, "ulpi"); + else if (parent->parent && parent->parent->of_node) + np = of_find_node_by_name(parent->parent->of_node, "ulpi"); + if (!np) + return 0; + + child = of_get_next_available_child(np, NULL); + of_node_put(np); + if (!child) + return -EINVAL; - ulpi->dev.parent = dev; /* needed early for ops */ + ulpi->dev.of_node = child; + + return 0; +} + +static int ulpi_read_id(struct ulpi *ulpi) +{ + int ret; /* Test the interface */ ret = ulpi_write(ulpi, ULPI_SCRATCH, 0xaa); if (ret < 0) - return ret; + goto err; ret = ulpi_read(ulpi, ULPI_SCRATCH); if (ret < 0) return ret; if (ret != 0xaa) - return -ENODEV; + goto err; ulpi->id.vendor = ulpi_read(ulpi, ULPI_VENDOR_ID_LOW); ulpi->id.vendor |= ulpi_read(ulpi, ULPI_VENDOR_ID_HIGH) << 8; @@ -177,13 +221,35 @@ static int ulpi_register(struct device *dev, struct ulpi *ulpi) ulpi->id.product = ulpi_read(ulpi, ULPI_PRODUCT_ID_LOW); ulpi->id.product |= ulpi_read(ulpi, ULPI_PRODUCT_ID_HIGH) << 8; + /* Some ULPI devices don't have a vendor id so rely on OF match */ + if (ulpi->id.vendor == 0) + goto err; + + request_module("ulpi:v%04xp%04x", ulpi->id.vendor, ulpi->id.product); + return 0; +err: + of_device_request_module(&ulpi->dev); + return 0; +} + +static int ulpi_register(struct device *dev, struct ulpi *ulpi) +{ + int ret; + + ulpi->dev.parent = dev; /* needed early for ops */ ulpi->dev.bus = &ulpi_bus; ulpi->dev.type = &ulpi_dev_type; dev_set_name(&ulpi->dev, "%s.ulpi", dev_name(dev)); ACPI_COMPANION_SET(&ulpi->dev, ACPI_COMPANION(dev)); - request_module("ulpi:v%04xp%04x", ulpi->id.vendor, ulpi->id.product); + ret = ulpi_of_register(ulpi); + if (ret) + return ret; + + ret = ulpi_read_id(ulpi); + if (ret) + return ret; ret = device_register(&ulpi->dev); if (ret) @@ -234,6 +300,7 @@ EXPORT_SYMBOL_GPL(ulpi_register_interface); */ void ulpi_unregister_interface(struct ulpi *ulpi) { + of_node_put(ulpi->dev.of_node); device_unregister(&ulpi->dev); } EXPORT_SYMBOL_GPL(ulpi_unregister_interface); -- 2.10.0.297.gf6727b0