From: Chris Zhong <zyw@rock-chips.com>
To: linux-rockchip@lists.infradead.org, thierry.reding@gmail.com
Cc: Chris Zhong <zyw@rock-chips.com>, David Airlie <airlied@linux.ie>,
        linux-kernel@vger.kernel.org, dri-devel@lists.freedesktop.org
Subject: [PATCH v3 2/2] drm/panel: add innolux,p079zca panel driver
Date: Wed, 22 Mar 2017 09:53:07 +0800
Message-Id: <1490147587-4382-2-git-send-email-zyw@rock-chips.com>
In-Reply-To: <1490147587-4382-1-git-send-email-zyw@rock-chips.com>
References: <1490147587-4382-1-git-send-email-zyw@rock-chips.com>
Sender: linux-kernel-owner@vger.kernel.org
Content-Length: 10488
Lines: 408

Support Innolux P079ZCA 7.85" 768x1024 TFT LCD panel, it is a MIPI DSI
panel.

Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
---

Changes in v3:
- printk err after regulator_disable(innolux->supply)

Changes in v2:
- add some error check
- always use Low power mode to send commend
- add comments for all the sleep
- use DRM_DEV_ERROR instead of dev_err

 drivers/gpu/drm/panel/Kconfig                 |  11 +
 drivers/gpu/drm/panel/Makefile                |   1 +
 drivers/gpu/drm/panel/panel-innolux-p079zca.c | 345 ++++++++++++++++++++++++++
 3 files changed, 357 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-innolux-p079zca.c

diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index 62aba97..99dd010 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -18,6 +18,17 @@ config DRM_PANEL_SIMPLE
 	  that it can be automatically turned off when the panel goes into a
 	  low power state.
 
+config DRM_PANEL_INNOLUX_P079ZCA
+	tristate "Innolux P079ZCA panel"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	depends on BACKLIGHT_CLASS_DEVICE
+	help
+	  Say Y here if you want to enable support for Innolux P079ZCA
+	  TFT-LCD modules. The panel has a 1024x768 resolution and uses
+	  24 bit RGB per pixel. It provides a MIPI DSI interface to
+	  the host and has a built-in LED backlight.
+
 config DRM_PANEL_JDI_LT070ME05000
 	tristate "JDI LT070ME05000 WUXGA DSI panel"
 	depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index a5c7ec0..bda2aa4 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -1,4 +1,5 @@
 obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o
+obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o
 obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o
 obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o
 obj-$(CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00) += panel-panasonic-vvx10f034n00.o
diff --git a/drivers/gpu/drm/panel/panel-innolux-p079zca.c b/drivers/gpu/drm/panel/panel-innolux-p079zca.c
new file mode 100644
index 0000000..9f3423a0
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-innolux-p079zca.c
@@ -0,0 +1,345 @@
+/*
+ * Copyright (c) 2017, Fuzhou Rockchip Electronics Co., Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/backlight.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regulator/consumer.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_panel.h>
+
+#include <video/mipi_display.h>
+
+struct innolux_panel {
+	struct drm_panel base;
+	struct mipi_dsi_device *link;
+
+	struct backlight_device *backlight;
+	struct regulator *supply;
+	struct gpio_desc *enable_gpio;
+
+	bool prepared;
+	bool enabled;
+};
+
+static inline struct innolux_panel *to_innolux_panel(struct drm_panel *panel)
+{
+	return container_of(panel, struct innolux_panel, base);
+}
+
+static int innolux_panel_disable(struct drm_panel *panel)
+{
+	struct innolux_panel *innolux = to_innolux_panel(panel);
+	int err;
+
+	if (!innolux->enabled)
+		return 0;
+
+	if (innolux->backlight) {
+		innolux->backlight->props.power = FB_BLANK_POWERDOWN;
+		backlight_update_status(innolux->backlight);
+	}
+
+	err = mipi_dsi_dcs_set_display_off(innolux->link);
+	if (err < 0)
+		DRM_DEV_ERROR(panel->dev, "failed to set display off: %d\n",
+			      err);
+
+	innolux->enabled = false;
+
+	return 0;
+}
+
+static int innolux_panel_unprepare(struct drm_panel *panel)
+{
+	struct innolux_panel *innolux = to_innolux_panel(panel);
+	int err;
+
+	if (!innolux->prepared)
+		return 0;
+
+	err = mipi_dsi_dcs_enter_sleep_mode(innolux->link);
+	if (err < 0) {
+		DRM_DEV_ERROR(panel->dev, "failed to enter sleep mode: %d\n",
+			      err);
+		return err;
+	}
+
+	gpiod_set_value_cansleep(innolux->enable_gpio, 0);
+
+	/* T8: 80ms - 1000ms */
+	msleep(80);
+
+	err = regulator_disable(innolux->supply);
+	if (err < 0)
+		return err;
+
+	innolux->prepared = false;
+
+	return 0;
+}
+
+static int innolux_panel_prepare(struct drm_panel *panel)
+{
+	struct innolux_panel *innolux = to_innolux_panel(panel);
+	int err, regulator_err;
+
+	if (innolux->prepared)
+		return 0;
+
+	gpiod_set_value_cansleep(innolux->enable_gpio, 0);
+
+	err = regulator_enable(innolux->supply);
+	if (err < 0)
+		return err;
+
+	/* T2: 15ms - 1000ms */
+	usleep_range(15000, 16000);
+
+	gpiod_set_value_cansleep(innolux->enable_gpio, 1);
+
+	/* T4: 15ms - 1000ms */
+	usleep_range(15000, 16000);
+
+	err = mipi_dsi_dcs_exit_sleep_mode(innolux->link);
+	if (err < 0) {
+		DRM_DEV_ERROR(panel->dev, "failed to exit sleep mode: %d\n",
+			      err);
+		goto poweroff;
+	}
+
+	/* T6: 120ms - 1000ms*/
+	msleep(120);
+
+	err = mipi_dsi_dcs_set_display_on(innolux->link);
+	if (err < 0) {
+		DRM_DEV_ERROR(panel->dev, "failed to set display on: %d\n",
+			      err);
+		goto poweroff;
+	}
+
+	/* T7: 5ms */
+	usleep_range(5000, 6000);
+
+	innolux->prepared = true;
+
+	return 0;
+
+poweroff:
+	regulator_err = regulator_disable(innolux->supply);
+	if (regulator_err)
+		DRM_DEV_ERROR(panel->dev, "failed to disable regulator: %d\n",
+			      regulator_err);
+
+	gpiod_set_value_cansleep(innolux->enable_gpio, 0);
+	return err;
+}
+
+static int innolux_panel_enable(struct drm_panel *panel)
+{
+	struct innolux_panel *innolux = to_innolux_panel(panel);
+	int ret;
+
+	if (innolux->enabled)
+		return 0;
+
+	if (innolux->backlight) {
+		innolux->backlight->props.power = FB_BLANK_UNBLANK;
+		ret = backlight_update_status(innolux->backlight);
+		if (ret) {
+			DRM_DEV_ERROR(panel->drm->dev,
+				      "Failed to enable backlight %d\n", ret);
+			return ret;
+		}
+	}
+
+	innolux->enabled = true;
+
+	return 0;
+}
+
+static const struct drm_display_mode default_mode = {
+	.clock = 56900,
+	.hdisplay = 768,
+	.hsync_start = 768 + 40,
+	.hsync_end = 768 + 40 + 40,
+	.htotal = 768 + 40 + 40 + 40,
+	.vdisplay = 1024,
+	.vsync_start = 1024 + 20,
+	.vsync_end = 1024 + 20 + 4,
+	.vtotal = 1024 + 20 + 4 + 20,
+	.vrefresh = 60,
+};
+
+static int innolux_panel_get_modes(struct drm_panel *panel)
+{
+	struct drm_display_mode *mode;
+
+	mode = drm_mode_duplicate(panel->drm, &default_mode);
+	if (!mode) {
+		DRM_DEV_ERROR(panel->drm->dev, "failed to add mode %ux%ux@%u\n",
+			      default_mode.hdisplay, default_mode.vdisplay,
+			      default_mode.vrefresh);
+		return -ENOMEM;
+	}
+
+	drm_mode_set_name(mode);
+
+	drm_mode_probed_add(panel->connector, mode);
+
+	panel->connector->display_info.width_mm = 120;
+	panel->connector->display_info.height_mm = 160;
+
+	return 1;
+}
+
+static const struct drm_panel_funcs innolux_panel_funcs = {
+	.disable = innolux_panel_disable,
+	.unprepare = innolux_panel_unprepare,
+	.prepare = innolux_panel_prepare,
+	.enable = innolux_panel_enable,
+	.get_modes = innolux_panel_get_modes,
+};
+
+static const struct of_device_id innolux_of_match[] = {
+	{ .compatible = "innolux,p079zca", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, innolux_of_match);
+
+static int innolux_panel_add(struct innolux_panel *innolux)
+{
+	struct device *dev = &innolux->link->dev;
+	struct device_node *np;
+	int err;
+
+	innolux->supply = devm_regulator_get(dev, "power");
+	if (IS_ERR(innolux->supply))
+		return PTR_ERR(innolux->supply);
+
+	innolux->enable_gpio = devm_gpiod_get_optional(dev, "enable",
+						       GPIOD_OUT_HIGH);
+	if (IS_ERR(innolux->enable_gpio)) {
+		err = PTR_ERR(innolux->enable_gpio);
+		dev_dbg(dev, "failed to get enable gpio: %d\n", err);
+		innolux->enable_gpio = NULL;
+	}
+
+	np = of_parse_phandle(dev->of_node, "backlight", 0);
+	if (np) {
+		innolux->backlight = of_find_backlight_by_node(np);
+		of_node_put(np);
+
+		if (!innolux->backlight)
+			return -EPROBE_DEFER;
+	}
+
+	drm_panel_init(&innolux->base);
+	innolux->base.funcs = &innolux_panel_funcs;
+	innolux->base.dev = &innolux->link->dev;
+
+	err = drm_panel_add(&innolux->base);
+	if (err < 0)
+		goto put_backlight;
+
+	return 0;
+
+put_backlight:
+	if (innolux->backlight)
+		put_device(&innolux->backlight->dev);
+
+	return err;
+}
+
+static void innolux_panel_del(struct innolux_panel *innolux)
+{
+	if (innolux->base.dev)
+		drm_panel_remove(&innolux->base);
+
+	if (innolux->backlight)
+		put_device(&innolux->backlight->dev);
+}
+
+static int innolux_panel_probe(struct mipi_dsi_device *dsi)
+{
+	struct innolux_panel *innolux;
+	int err;
+
+	dsi->lanes = 4;
+	dsi->format = MIPI_DSI_FMT_RGB888;
+	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE |
+			  MIPI_DSI_MODE_LPM;
+
+	innolux = devm_kzalloc(&dsi->dev, sizeof(*innolux), GFP_KERNEL);
+	if (!innolux)
+		return -ENOMEM;
+
+	mipi_dsi_set_drvdata(dsi, innolux);
+
+	innolux->link = dsi;
+
+	err = innolux_panel_add(innolux);
+	if (err < 0)
+		return err;
+
+	err = mipi_dsi_attach(dsi);
+	return err;
+}
+
+static int innolux_panel_remove(struct mipi_dsi_device *dsi)
+{
+	struct innolux_panel *innolux = mipi_dsi_get_drvdata(dsi);
+	int err;
+
+	err = innolux_panel_unprepare(&innolux->base);
+	if (err < 0)
+		DRM_DEV_ERROR(&dsi->dev, "failed to unprepare panel: %d\n",
+			      err);
+
+	err = innolux_panel_disable(&innolux->base);
+	if (err < 0)
+		DRM_DEV_ERROR(&dsi->dev, "failed to disable panel: %d\n", err);
+
+	err = mipi_dsi_detach(dsi);
+	if (err < 0)
+		DRM_DEV_ERROR(&dsi->dev, "failed to detach from DSI host: %d\n",
+			      err);
+
+	drm_panel_detach(&innolux->base);
+	innolux_panel_del(innolux);
+
+	return 0;
+}
+
+static void innolux_panel_shutdown(struct mipi_dsi_device *dsi)
+{
+	struct innolux_panel *innolux = mipi_dsi_get_drvdata(dsi);
+
+	innolux_panel_unprepare(&innolux->base);
+	innolux_panel_disable(&innolux->base);
+}
+
+static struct mipi_dsi_driver innolux_panel_driver = {
+	.driver = {
+		.name = "panel-innolux-p079zca",
+		.of_match_table = innolux_of_match,
+	},
+	.probe = innolux_panel_probe,
+	.remove = innolux_panel_remove,
+	.shutdown = innolux_panel_shutdown,
+};
+module_mipi_dsi_driver(innolux_panel_driver);
+
+MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
+MODULE_DESCRIPTION("Innolux P079ZCA panel driver");
+MODULE_LICENSE("GPL v2");
-- 
2.6.3