Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S933426AbdCaQ7z (ORCPT ); Fri, 31 Mar 2017 12:59:55 -0400 Received: from mx2.suse.de ([195.135.220.15]:43224 "EHLO mx2.suse.de" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S933204AbdCaQ7x (ORCPT ); Fri, 31 Mar 2017 12:59:53 -0400 Subject: Re: [PATCH] arm64: dts: rk3399: add support for firefly-rk3399 board To: Kever Yang References: <1490954348-13889-1-git-send-email-kever.yang@rock-chips.com> <1860080.ebfBDdk4Fv@phil> Cc: Heiko Stuebner , linux-rockchip@lists.infradead.org, devicetree@vger.kernel.org, Jianqun Xu , linux-kernel@vger.kernel.org, Andy Yan , Rob Herring , linux-arm-kernel@lists.infradead.org, Will Deacon , Mark Rutland , Catalin Marinas , Matthias Brugger From: =?UTF-8?Q?Andreas_F=c3=a4rber?= Organization: SUSE Linux GmbH Message-ID: <9cfe8ee4-16bc-fa5a-78bc-1939d595101a@suse.de> Date: Fri, 31 Mar 2017 18:59:49 +0200 User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:45.0) Gecko/20100101 Thunderbird/45.7.0 MIME-Version: 1.0 In-Reply-To: <1860080.ebfBDdk4Fv@phil> Content-Type: text/plain; charset=windows-1252 Content-Transfer-Encoding: 8bit Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 19789 Lines: 673 Hi, Am 31.03.2017 um 14:56 schrieb Heiko Stuebner: > Hi Kever, > > Am Freitag, 31. M?rz 2017, 17:59:07 CEST schrieb Kever Yang: >> Firefly-rk3399 is a bord from T-Firefly, you can find detail about >> it here: >> http://en.t-firefly.com/en/firenow/Firefly_RK3399/ >> >> This patch add basic node for the board and make it able to bring >> up. > > This more a first glance, I didn't check every binding, but already found > some dubious ones, so in general, please make sure to only include nodes > with approved bindings. > > > [...] > >> arch/arm64/boot/dts/rockchip/Makefile | 1 + >> arch/arm64/boot/dts/rockchip/rk3399-firefly.dts | 772 ++++++++++++++++++++++++ > > please provide a binding addition for the board in a separate patch as well. > > >> 2 files changed, 773 insertions(+) >> create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-firefly.dts >> >> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile >> index 3a86289..dd3d550 100644 >> --- a/arch/arm64/boot/dts/rockchip/Makefile >> +++ b/arch/arm64/boot/dts/rockchip/Makefile >> @@ -4,6 +4,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb >> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-px5-evb.dtb >> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb >> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb >> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-firefly.dtb > > if possible, please rebase on top of my for-next branch, as we also > have the first gru board in there now. > >> >> always := $(dtb-y) >> subdir-y := $(dts-dirs) >> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts b/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts >> new file mode 100644 >> index 0000000..686977b >> --- /dev/null >> +++ b/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts >> @@ -0,0 +1,772 @@ >> +/* >> + * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd "Ltd."? >> + * >> + * This file is dual-licensed: you can use it either under the terms >> + * of the GPL or the X11 license, at your option. Note that this dual >> + * licensing only applies to this file, and not this project as a >> + * whole. >> + * >> + * a) This file is free software; you can redistribute it and/or >> + * modify it under the terms of the GNU General Public License as >> + * published by the Free Software Foundation; either version 2 of the >> + * License, or (at your option) any later version. >> + * >> + * This file is distributed in the hope that it will be useful, >> + * but WITHOUT ANY WARRANTY; without even the implied warranty of >> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the >> + * GNU General Public License for more details. >> + * >> + * Or, alternatively, >> + * >> + * b) Permission is hereby granted, free of charge, to any person >> + * obtaining a copy of this software and associated documentation >> + * files (the "Software"), to deal in the Software without >> + * restriction, including without limitation the rights to use, >> + * copy, modify, merge, publish, distribute, sublicense, and/or >> + * sell copies of the Software, and to permit persons to whom the >> + * Software is furnished to do so, subject to the following >> + * conditions: >> + * >> + * The above copyright notice and this permission notice shall be >> + * included in all copies or substantial portions of the Software. >> + * >> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, >> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES >> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND >> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT >> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, >> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING >> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR >> + * OTHER DEALINGS IN THE SOFTWARE. This should be shorter: "SPDX-License-Identifier: GPL-2.0+ OR MIT" >> + */ >> + >> +/dts-v1/; >> +#include >> +#include "rk3399.dtsi" >> + >> +/ { >> + model = "Rockchip RK3399 Firefly Board (Linux Opensource)"; "(Linux Opensource)" is not a hardware description, please drop. >> + compatible = "rockchip,rk3399-firefly-linux", "rockchip,rk3399"; > > Just to make sure, is this really a Rockchip board? I would've expected > to see something like "firefly,firefly-rk3399" here, like on the rk3288- > variant. Not a requirement, just a question to clarify who designed the > board please :-) . +1, especially no -linux suffix please. The same device tree should in theory be usable with Linux, Android, FreeBSD or any other OS with drivers based on the official bindings. >> + >> + backlight: backlight { >> + status = "okay"; >> + compatible = "pwm-backlight"; >> + enable-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; >> + pwms = <&pwm0 0 25000 0>; >> + brightness-levels = < >> + 0 1 2 3 4 5 6 7 >> + 8 9 10 11 12 13 14 15 >> + 16 17 18 19 20 21 22 23 >> + 24 25 26 27 28 29 30 31 >> + 32 33 34 35 36 37 38 39 >> + 40 41 42 43 44 45 46 47 >> + 48 49 50 51 52 53 54 55 >> + 56 57 58 59 60 61 62 63 >> + 64 65 66 67 68 69 70 71 >> + 72 73 74 75 76 77 78 79 >> + 80 81 82 83 84 85 86 87 >> + 88 89 90 91 92 93 94 95 >> + 96 97 98 99 100 101 102 103 >> + 104 105 106 107 108 109 110 111 >> + 112 113 114 115 116 117 118 119 >> + 120 121 122 123 124 125 126 127 >> + 128 129 130 131 132 133 134 135 >> + 136 137 138 139 140 141 142 143 >> + 144 145 146 147 148 149 150 151 >> + 152 153 154 155 156 157 158 159 >> + 160 161 162 163 164 165 166 167 >> + 168 169 170 171 172 173 174 175 >> + 176 177 178 179 180 181 182 183 >> + 184 185 186 187 188 189 190 191 >> + 192 193 194 195 196 197 198 199 >> + 200 201 202 203 204 205 206 207 >> + 208 209 210 211 212 213 214 215 >> + 216 217 218 219 220 221 222 223 >> + 224 225 226 227 228 229 230 231 >> + 232 233 234 235 236 237 238 239 >> + 240 241 242 243 244 245 246 247 >> + 248 249 250 251 252 253 254 255>; >> + default-brightness-level = <200>; >> + }; >> + >> + clkin_gmac: external-gmac-clock { >> + compatible = "fixed-clock"; >> + clock-frequency = <125000000>; >> + clock-output-names = "clkin_gmac"; >> + #clock-cells = <0>; >> + }; >> + >> + rt5640-sound { Drop rt5640- node prefix, or is there more than one? >> + compatible = "simple-audio-card"; >> + simple-audio-card,format = "i2s"; >> + simple-audio-card,name = "rockchip,rt5640-codec"; >> + simple-audio-card,mclk-fs = <256>; >> + simple-audio-card,widgets = >> + "Microphone", "Mic Jack", >> + "Headphone", "Headphone Jack"; >> + simple-audio-card,routing = >> + "Mic Jack", "MICBIAS1", >> + "IN1P", "Mic Jack", >> + "Headphone Jack", "HPOL", >> + "Headphone Jack", "HPOR"; >> + simple-audio-card,cpu { >> + sound-dai = <&i2s1>; >> + }; >> + simple-audio-card,codec { >> + sound-dai = <&rt5640>; >> + }; Insert while lines before these two nodes for readability? >> + }; >> + >> + sdio_pwrseq: sdio-pwrseq { >> + compatible = "mmc-pwrseq-simple"; >> + clocks = <&rk808 1>; >> + clock-names = "ext_clock"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&wifi_enable_h>; >> + >> + /* >> + * On the module itself this is one of these (depending >> + * on the actual card populated): >> + * - SDIO_RESET_L_WL_REG_ON >> + * - PDN (power down when low) >> + */ >> + reset-gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; /* GPIO0_B2 */ > > Thanks to Andy's persistence, we have nice constants in the pinctrl- > binding-header now, like RK_PB2 for the above. So you can drop the > comment and use the constant instead for easier reading. > Same for other pins. > > >> + }; >> + >> + vcc3v3_pcie: vcc3v3-pcie-regulator { >> + compatible = "regulator-fixed"; >> + enable-active-high; >> + regulator-always-on; >> + regulator-boot-on; >> + gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pcie_drv>; >> + regulator-name = "vcc3v3_pcie"; >> + }; >> + >> + vcc3v3_sys: vcc3v3-sys { >> + compatible = "regulator-fixed"; >> + regulator-name = "vcc3v3_sys"; >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + }; >> + >> + vcc5v0_host: vcc5v0-host-regulator { >> + compatible = "regulator-fixed"; >> + enable-active-high; >> + gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&host_vbus_drv>; >> + regulator-name = "vcc5v0_host"; >> + regulator-always-on; >> + }; >> + >> + vcc5v0_sys: vcc5v0-sys { >> + compatible = "regulator-fixed"; >> + regulator-name = "vcc5v0_sys"; >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <5000000>; >> + regulator-max-microvolt = <5000000>; >> + }; >> + >> + vcc_phy: vcc-phy-regulator { >> + compatible = "regulator-fixed"; >> + regulator-name = "vcc_phy"; >> + regulator-always-on; >> + regulator-boot-on; >> + }; >> + >> + vdd_log: vdd-log { >> + compatible = "pwm-regulator"; >> + pwms = <&pwm2 0 25000 1>; >> + regulator-name = "vdd_log"; >> + regulator-min-microvolt = <800000>; >> + regulator-max-microvolt = <1400000>; >> + regulator-always-on; >> + regulator-boot-on; >> + >> + /* for rockchip boot on */ >> + rockchip,pwm_id= <2>; >> + rockchip,pwm_voltage = <1000000>; >> + }; >> + >> + vccadc_ref: vccadc-ref { >> + compatible = "regulator-fixed"; >> + regulator-name = "vcc1v8_sys"; >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + }; >> + >> + wireless-wlan { >> + compatible = "wlan-platdata"; >> + rockchip,grf = <&grf>; >> + wifi_chip_type = "ap6354"; >> + sdio_vref = <1800>; >> + WIFI,host_wake_irq = <&gpio0 3 GPIO_ACTIVE_HIGH>; /* GPIO0_a3 */ >> + status = "okay"; > > that is not a valid binding, am I right? ;-) > So should be dropped. ... or should be replaced by the proper binding (brcmfmac probably?). > >> + }; >> + >> + wireless-bluetooth { >> + compatible = "bluetooth-platdata"; >> + //wifi-bt-power-toggle; >> + uart_rts_gpios = <&gpio2 19 GPIO_ACTIVE_LOW>; /* GPIO2_C3 */ >> + pinctrl-names = "default", "rts_gpio"; >> + pinctrl-0 = <&uart0_rts>; >> + pinctrl-1 = <&uart0_gpios>; >> + //BT,power_gpio = <&gpio3 19 GPIO_ACTIVE_HIGH>; /* GPIOx_xx */ >> + BT,reset_gpio = <&gpio0 9 GPIO_ACTIVE_HIGH>; /* GPIO0_B1 */ >> + BT,wake_gpio = <&gpio2 26 GPIO_ACTIVE_HIGH>; /* GPIO2_D2 */ >> + BT,wake_host_irq = <&gpio0 4 GPIO_ACTIVE_HIGH>; /* GPIO0_A4 */ >> + status = "okay"; >> + }; > > same here Move to corresponding uart node? (serdev bindings) >> +}; >> + >> +&cpu_l0 { >> + cpu-supply = <&vdd_cpu_l>; >> +}; >> + >> +&cpu_l1 { >> + cpu-supply = <&vdd_cpu_l>; >> +}; >> + >> +&cpu_l2 { >> + cpu-supply = <&vdd_cpu_l>; >> +}; >> + >> +&cpu_l3 { >> + cpu-supply = <&vdd_cpu_l>; >> +}; >> + >> +&cpu_b0 { >> + cpu-supply = <&vdd_cpu_b>; >> +}; >> + >> +&cpu_b1 { >> + cpu-supply = <&vdd_cpu_b>; >> +}; >> + >> +&emmc_phy { >> + status = "okay"; >> +}; >> + >> +&gmac { >> + assigned-clocks = <&cru SCLK_RMII_SRC>; >> + assigned-clock-parents = <&clkin_gmac>; >> + clock_in_out = "input"; >> + phy-supply = <&vcc_phy>; >> + phy-mode = "rgmii"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&rgmii_pins>; >> + snps,reset-gpio = <&gpio3 15 GPIO_ACTIVE_LOW>; >> + snps,reset-active-low; >> + snps,reset-delays-us = <0 10000 50000>; >> + tx_delay = <0x28>; >> + rx_delay = <0x11>; >> + status = "okay"; >> +}; >> + >> +&i2c0 { >> + status = "okay"; >> + i2c-scl-rising-time-ns = <168>; >> + i2c-scl-falling-time-ns = <4>; >> + clock-frequency = <400000>; >> + >> + vdd_cpu_b: syr827@40 { Node name should not duplicate the model. pmic@40? >> + compatible = "silergy,syr827"; >> + reg = <0x40>; >> + vin-supply = <&vcc5v0_sys>; >> + regulator-compatible = "fan53555-reg"; >> + regulator-name = "vdd_cpu_b"; >> + regulator-min-microvolt = <712500>; >> + regulator-max-microvolt = <1500000>; >> + regulator-ramp-delay = <1000>; >> + vsel-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; >> + fcs,suspend-voltage-selector = <0>; >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-initial-state = <3>; >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + vdd_gpu: syr828@41 { Ditto. >> + compatible = "silergy,syr828"; >> + reg = <0x41>; >> + vin-supply = <&vcc5v0_sys>; >> + regulator-compatible = "fan53555-reg"; >> + regulator-name = "vdd_gpu"; >> + regulator-min-microvolt = <712500>; >> + regulator-max-microvolt = <1500000>; >> + regulator-ramp-delay = <1000>; >> + fcs,suspend-voltage-selector = <1>; >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-initial-state = <3>; >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + rk808: pmic@1b { Sort order: Any reason that 1b is after 40, 41? >> + compatible = "rockchip,rk808"; >> + reg = <0x1b>; >> + interrupt-parent = <&gpio1>; >> + interrupts = <21 IRQ_TYPE_LEVEL_LOW>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pmic_int_l>; >> + rockchip,system-power-controller; >> + wakeup-source; >> + #clock-cells = <1>; >> + clock-output-names = "xin32k", "rk808-clkout2"; >> + >> + vcc1-supply = <&vcc3v3_sys>; >> + vcc2-supply = <&vcc3v3_sys>; >> + vcc3-supply = <&vcc3v3_sys>; >> + vcc4-supply = <&vcc3v3_sys>; >> + vcc6-supply = <&vcc3v3_sys>; >> + vcc7-supply = <&vcc3v3_sys>; >> + vcc8-supply = <&vcc3v3_sys>; >> + vcc9-supply = <&vcc3v3_sys>; >> + vcc10-supply = <&vcc3v3_sys>; >> + vcc11-supply = <&vcc3v3_sys>; >> + vcc12-supply = <&vcc3v3_sys>; >> + vddio-supply = <&vcc1v8_pmu>; >> + >> + regulators { >> + vdd_center: DCDC_REG1 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <750000>; >> + regulator-max-microvolt = <1350000>; >> + regulator-ramp-delay = <6001>; >> + regulator-name = "vdd_center"; >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + vdd_cpu_l: DCDC_REG2 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <750000>; >> + regulator-max-microvolt = <1350000>; >> + regulator-ramp-delay = <6001>; >> + regulator-name = "vdd_cpu_l"; >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + vcc_ddr: DCDC_REG3 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-name = "vcc_ddr"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + }; >> + }; >> + >> + vcc_1v8: DCDC_REG4 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-name = "vcc_1v8"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + regulator-suspend-microvolt = <1800000>; >> + }; >> + }; >> + >> + vcc1v8_dvp: LDO_REG1 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-name = "vcc1v8_dvp"; >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + vcc3v0_tp: LDO_REG2 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3000000>; >> + regulator-name = "vcc3v0_tp"; >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + vcc1v8_pmu: LDO_REG3 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-name = "vcc1v8_pmu"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + regulator-suspend-microvolt = <1800000>; >> + }; >> + }; >> + >> + vcc_sd: LDO_REG4 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-name = "vcc_sd"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + regulator-suspend-microvolt = <3300000>; >> + }; >> + }; >> + >> + vcca3v0_codec: LDO_REG5 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3000000>; >> + regulator-name = "vcca3v0_codec"; >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + vcc_1v5: LDO_REG6 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <1500000>; >> + regulator-max-microvolt = <1500000>; >> + regulator-name = "vcc_1v5"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + regulator-suspend-microvolt = <1500000>; >> + }; >> + }; >> + >> + vcca1v8_codec: LDO_REG7 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-name = "vcca1v8_codec"; >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + vcc_3v0: LDO_REG8 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3000000>; >> + regulator-name = "vcc_3v0"; >> + regulator-state-mem { >> + regulator-on-in-suspend; >> + regulator-suspend-microvolt = <3000000>; >> + }; >> + }; >> + >> + vcc3v3_s3: SWITCH_REG1 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-name = "vcc3v3_s3"; >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + >> + vcc3v3_s0: SWITCH_REG2 { >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-name = "vcc3v3_s0"; >> + regulator-state-mem { >> + regulator-off-in-suspend; >> + }; >> + }; >> + }; >> + }; >> +}; >> + >> +&i2c1 { >> + status = "okay"; >> + i2c-scl-rising-time-ns = <300>; >> + i2c-scl-falling-time-ns = <15>; >> + >> + gsl3673: gsl3673@40 { Node name? >> + compatible = "GSL,GSL3673"; >> + reg = <0x40>; >> + screen_max_x = <1536>; >> + screen_max_y = <2048>; >> + irq_gpio_number = <&gpio1 20 IRQ_TYPE_LEVEL_LOW>; >> + rst_gpio_number = <&gpio4 22 GPIO_ACTIVE_HIGH>; > > Again doesn't look like a valid binding. > > >> + }; >> + >> + rt5640: rt5640@1c { Node name: codec@1c? >> + #sound-dai-cells = <0>; >> + compatible = "realtek,rt5640"; >> + reg = <0x1c>; >> + clocks = <&cru SCLK_I2S_8CH_OUT>; >> + clock-names = "mclk"; >> + realtek,in1-differential; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&rt5640_hpcon>; >> + hp-con-gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>; >> + //hp-det-gpio = <&gpio4 28 GPIO_ACTIVE_LOW>; > > don't add commented lines please > > >> + io-channels = <&saradc 4>; >> + hp-det-adc-value = <500>; >> + }; >> +}; >> + >> +&i2c3 { >> + status = "okay"; >> + i2c-scl-rising-time-ns = <450>; >> + i2c-scl-falling-time-ns = <15>; >> +}; >> + >> +&i2c4 { >> + status = "okay"; >> + i2c-scl-rising-time-ns = <600>; >> + i2c-scl-falling-time-ns = <20>; >> + >> + fusb0: fusb30x@22 { Node name? >> + compatible = "fairchild,fusb302"; > > Has this made its way into the kernel yet? Regards, Andreas -- SUSE Linux GmbH, Maxfeldstr. 5, 90409 N?rnberg, Germany GF: Felix Imend?rffer, Jane Smithard, Graham Norton HRB 21284 (AG N?rnberg)